Yamaha | NS-333 | manual | Yamaha NS-333 User manual

05HO2CIG6WGUFC[(GDTWCT[2/
OWNER'S MANUAL
NS-333
UGRT
Speaker System
Thank you for selecting a YAMAHA speaker system.
.
PRECAUTIONS
PLACING THE SPEAKERS
Read these precautions carefully before using your
speakers.
Place the speakers on a sturdy, vibration-free surface, on a
well-built stand.
• To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
• Install the speakers in a cool, dry, clean place - away
from windows, heat sources, sources of excessive
vibration, dust, moisture and cold. Avoid sources of
humming (transformers, motors). To prevent fire or
electrical shock, do not expose the speakers to rain or
water.
• To prevent the enclosure from warping or discoloring,
do not place the speakers where they will be exposed to
direct sunlight or excessive humidity.
• Do not place the following objects on the speakers:
Glass, china, etc.
If glass etc. falls by vibrations and breaks, it may
cause bodily injury.
A burning candle etc.
If the candle falls by vibrations, it may cause fire and
bodily injury.
A vessel with water in it
If the vessel falls by vibrations and water spills, it may
cause damage to the speakers, and/or you may get an
electric shock.
• Do not place the speakers where foreign objects such as
water drips might fall. It might cause a fire, damage to
the speakers, and/or bodily injury.
• Do not place the speakers where they are liable to be
knocked over or struck by falling objects. Stable
placement will also ensure better sound performance.
• Placing the speakers on the same shelf or rack as the
turntable can result in feedback.
• Any time you note distortion, reduce the volume control
on your amplifier to a lower setting. Never allow your
amplifier to be driven into “clipping”. Otherwise the
speakers may be damaged.
• When using an amplifier with a rated output power
higher than the nominal input power of the speakers,
care should be taken never to exceed the speakers’
maximum input.
• Do not attempt to clean the speakers with chemical solvents as
this might damage the finish. Use a clean, dry cloth.
• Do not attempt to modify or fix the speakers. Contact
qualified YAMAHA service personnel when any service
is needed. The cabinet should never be opened for any
reasons.
• Secure placement or installation is the owner’s
responsibility. YAMAHA shall not be liable for any
accident caused by improper placement or
installation of speakers.
■Using as 2ch stereo speakers
Better stereo images will be obtained when the speakers
are slightly angled in towards the listeners.
■Using as main speakers in a multi channel
system
Position the speakers on both sides of the TV. The
positioning of speakers is important, because it controls the
whole sound quality of a multi channel system. Set up the
speakers on the basis of your listening position by
following the owner’s manual supplied with your
amplifier.
■Using as front or rear effect speakers
Mount the speakers on a wall or place the speakers on a
shelf. Determine the best position by following the owner’s
manual supplied with your amplifier.
Main (R)
Main (L)
Subwoofer
Center
NS-333
This speaker features a magnetically shielded design, but there is
still a chance that placing it too close to a TV set might impair
picture color. Should this happen, move the speaker away from the
TV set.
1
English
Note
05HO2CIG6WGUFC[(GDTWCT[2/
■To mount the speaker on a wall by using
the attached mounting bracket
Fasten screws into a firm wall or wall support as shown in
the figure, and hang the holes of the mounting bracket on
the protruding screws.
* Make sure that the screws are securely caught by the
narrow parts of the holes.
Tapping screw (3.5–4 mm)
(Available at the hardware
store)
Connections
• Connect the screw-type input terminals at the rear of the
speaker to the speaker output terminals of the amplifier
(or receiver) with the speaker cable.
• Connect the (+) terminals on the amplifier (or receiver)
and the speaker using one side of the cable. Connect the
(–) terminals on both components using the other side of
the cable.
• Connect the speaker to the center terminals of the
amplifier (or receiver) making sure not to reverse the
polarity (+, –). If the speaker is connected with reversed
polarity, the sound will be unnatural and lack bass.
■How to Connect:
3 mm
Min.
20 mm
1 Remove the insulation coating at the extremity of each
speaker cable by twisting the coating off.
Wall/ Wall Support
WARNING
• This speaker weighs 5.0 kg (11 lbs.). Do not mount it
on thin plywood or a wall with soft surface material.
If mounted, the screws may come out of the flimsy
surface and the speaker may fall. This damages the
speaker or causes personal injury.
• Do not install the speaker to a wall with nails,
adhesives, or any other unstable hardware. Longterm use and vibrations may cause it to fall.
• To avoid accidents resulting from tripping over loose
speaker cable, fix it to the wall.
2 Loosen the terminal knob.
3 Insert the bare wire.
4 Tighten the knob and secure the cable. Test the
firmness of the connection by pulling lightly on the
cable at the terminal.
Note
Do not let the bare speaker wires touch each other as this could
damage the speaker or the amplifier, or both of them.
[Using a Banana Plug]
CONNECTIONS TO YOUR AMPLIFIER
2
Before making connections, make sure that
the amplifier is switched off.
1
Loosen
Tighten
Banana Plug
3
Black (-)
Red (+)
Speaker (R)
Speaker (L)
1 Remove the cover by pulling it toward you.
2 Tighten the terminal knob.
3 Simply insert the banana plug into the terminal.
SPEAKERS
R
Speakers output
terminals of the
amplifier
L
A
+
–
–
B
Amprifier or
Receiver
2
+
05HO2CIG6WGUFC[(GDTWCT[2/
REMOVING THE FRONT COVER
The front cover is fastened to the enclosure at four points
and can be removed if desired. To remove the cover, hold
on to both sides and slowly pull straight away from the
speaker. To reattach, line up the four pegs on the inside
surface of the cover with the four corresponding holes on
the speaker and push gently.
Note
SPECIFICATIONS
Type ...............2-way acoustic suspecsion speaker system
magnetic shielding type
Driver .......................................... 13 cm (5") cone woofer
2.5 cm (1") balanced dome tweeter
Frequency response.................................. 65 Hz – 35 kHz
Nominal impedance ...............................................6 ohms
Nominal input power ................................................60 W
Maximum input power............................................150 W
Sensitivity.................................................87 dB/2.83 V/m
Crossover frequency ................................................3 kHz
Dimensions (W x H x D) ...200 mm x 320 mm x 213 mm
(7.9"x 12.6" x 8.4")
Weight........................................................... 5 kg (11 lbs)
• Specifications subject to change without notice due to
product improvements.
• Care should be taken not to exceed the input power
values noted above.
When the cover is removed, take care not to touch the speaker
units with your hands or to exert excessive force with tools.
English
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising