Monogram ZV54I Owner`s manual

Monogram ZV54I Owner`s manual
Installation
Instructions
If you have questions, call 800.GE.CARES or visit our website at: monogram.com
Island Vent Hoods
Models:
ZV42I
ZV54I
Installation Instructions
WARNING:
BEFORE YOU BEGIN
TO REDUCE THE
RISK OF FIRE, ELECTRICAL SHOCK OR
INJURY, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have any questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power
off at the service panel and lock service panel to
prevent power from being switched on accidentally.
If the service panel cannot be locked, fasten a tag or
prominent warning label to the panel.
Read these instructions completely and
carefully.
• IMPORTANT – Save these instructions for local
inspector’s use.
• IMPORTANT – Observe all governing codes and
•
•
•
•
•
•
ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions for
future reference.
Skill Level – Installation of this vent hood requires
basic mechanical and electrical skills.
Completion time – 1 to 3 hours.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the Warranty.
AVERTISSEMENT
POUR RÉDUIRE LE RISQUE D’INCENDIE, DE
CHOC ÉLECTRIQUE OU DE BLESSURES, IL
FAUT OBSERVER LES REGLES SUIVANTES:
A. Utiliser cet appareil uniquement de la maniére
prévue par le fabricant. En cas de question,
consulter le fabricant.
B. Avant toute intervention ou nettoyage, couper
l’alimentation électrique au disjoncteur et verrouiller
le panneau du disjoncteur pour éviter la mise sous
tension accidentelle. S’il n’est pas possible de
verrouiller le panneau du disconcteur, attacher un
placard ou une étiquette trés visible au panneau.
• For general ventilating use only. Do not use to exhaust
hazardous or explosive materials or vapors.
• Structural framing, installation work and electrical
wiring must be done by qualified person(s) in
accordance with all applicable codes and
standards including fire-rated construction.
• Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow
the heating equipment manufacturer’s guideline and
safety standards such as those published by the
National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code
authorities.
• Local codes vary. Installation electrical connections
and grounding must comply with applicable codes.
In the absence of local codes, the vent should be
installed in accordance with National Electrical
Code ANSI/NFPA 70-1990 or latest edition.
CAUTION:
Due to the weight and size of these vent
hoods and to reduce the risk of personal injury or
damage to the product, THREE PEOPLE ARE REQUIRED
FOR PROPER INSTALLATION.
PRUDENCE
À cause du poids et des dimensions du ces
hottes et pour réduire les risques de blessures ou de
dommages du produit, IL FAUT TROIS PERSONNES
POUR FAIRE UNE INSTALLATION CORRECTE.
WARNING:
To reduce the risk of fire or electrical shock,
do not use this range hood with any external solid-state
speed control device. Any such alteration from original
factory wiring could result in damage to the unit and/or
create an electrical safety hazard.
AVERTISSEMENT
CAUTION: To reduce risk of fire
Pour réduire le risque d’incendie ou de
choc électrique, il ne faut pas utiliser cette hotte avec
un régulateur de vitesse électronique externe. Toute
modification de ce type du branchement d’usine peute
endommager l’appareil ou créer un risque de choc
électrique.
and to properly exhaust air, be sure to duct
air outside – Do not vent exhaust air into
spaces within walls or ceilings or into attics, crawl
spaces, or garages.
PRUDENCE
Il faut prendre
soin d’installer un conduit vers l’extérieur
pour réduire le risque d’incendie et pouvoir
évacuer l’air correctement. Il ne faut pas évacuer
l’air correctement. Il ne faut pas évacuer l’air dans
l’espace entre les parois d’un mur, un plafond ou un
grenier, un espace sanitaire ou un garage.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCTWORK.
2
Design Information
CONTENTS
Design Information
Product Dimensions ......................................................................3
Duct Cover Accessories ..............................................................4
Product Clearances ......................................................................4
Installation Instructions
Step 1, Construct Ceiling Support ......................................10–12
Step 2, Mount Template..............................................................13
Step 3, Size and Install Ductwork ............................................13
Step 4, Install Support Frame and Duct Covers ....................14
Step 5, Install Duct Transition and Damper ..........................15
Step 6, Install Hood to Support ................................................15
Step 7, Connect Duct ................................................................15
Step 8, Connect Electrical..........................................................16
Step 9, Install the Motor ............................................................16
Step 10, Slide Duct Cover Down ..............................................17
Step 11, Install Filters ..................................................................17
Step 12, Install Rods....................................................................17
Step 13, Install Supplied Duct Cover, Top Cover....................18
Step 14, Finalize Installation ......................................................18
Step 15, Installation Checklist ..................................................19
Advance Planning
Ductwork Planning ......................................................................5
Ceiling Framing for Support ........................................................5
Accessory Frames and Duct Covers ........................................5
Power Supply ................................................................................5
Installation Height ........................................................................6
Duct Fittings .................................................................................. 7
Installation Preparation
Tools and Materials Required ....................................................8
Remove the Packaging ................................................................8
Parts, Hardware, Accessory Packages ..................................9
42” HOOD DIMENSIONS
54” HOOD DIMENSIONS
Model ZV42I
Model ZV54I
14”
27-1/2"
16”
32-1/4"
25-3/4”
34"
33”
46"
20”
20"
24”
24"
31-3/4”
31-1/2"
36-1/4"
36-1/4”
42”
42"
Supplied duct covers dimensions: 16"W x 12"D x 9"H
54”
54"
Supplied duct covers dimensions: 20-1/4"W x 12"D x 5"H
These vent hoods are supplied with a support frame and
decorative duct cover for ceiling heights of 7’11" to 8’5".
The hood installation height is determined by the ceiling
height. Accessories are available to reach ceiling
heights from 8’6" to 10’4".
3
Design Information
PRODUCT CLEARANCES
DUCT COVER ACCESSORIES
*Height
to Ceiling
20" For ZV42I
24" For ZV54I
30" Min.
36" Max.
36" Min.
ZV42I
* 9" for ceiling heights 7’11" to 8’5" using the supplied
support frame and duct cover.
Order ZX42DC10 for ceiling heights of 8"6" to 10’4".
These vent hoods must be installed 30" min. to 36" max.
above the cooking surface. Exact installation height is
determined by ceiling height. The cooking surface
should be at least 36” above the floor.
ZV54I
* 5" for ceiling heights 7’11" to 8’5" using the supplied
support frame and duct cover.
Order ZX54DC10 for ceiling heights of 8"6" to 10’4".
IMPORTANT: Clearances may vary due to type of
cooking product and local codes. Check with local
inspectors to be sure standard is applicable.
• When installing these Island Hoods above a
Monogram Professional Range or Cooktop,
installation clearance must be at least 30".
These accessories include telescoping support
frames and decorative covers. Order the accessory
for your model at the same time as the vent hood and
have on site before installation begins.
4
Advance Planning
ADVANCE PLANNING
POWER SUPPLY
Ductwork Planning
• These vent hoods are equipped for 10” round
ductwork.
• Determine the exact location of the vent hood.
• Plan the route for venting exhaust to the outdoors.
• Use the shortest and straightest duct route possible.
For satisfactory performance, duct run should not
exceed 150 ft. equivalent length for any duct
configurations.
• Refer to “Duct Fittings” chart to compute the
maximum permissible length for duct runs to the
outdoors.
• Use rigid metal ductwork only.
• Install a roof cap with damper at the exterior opening.
Order the cap and any transitions needed in advance.
IMPORTANT - (Please read carefully)
Ceiling Framing for Adequate Support
• These vent hoods are heavy. Adequate structural
support must be provided. The ceiling structure must
be capable of supporting the weight of the hood and
any inadvertent user contact loads (approximately 300
pounds). The hood support frame will be supported by
2 x 4 cross framing.
Electrical Supply
This vent hood must be supplied with 120V, 60Hz,
and connected to an individual, properly grounded
branch circuit, and protected by a 15 or 20 amp
circuit breaker or time delay fuse.
• Wiring must be 2 wire with ground.
• If the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
• Route house wiring in the ceiling, as close to the
installation location as possible. Allow additional
length from ceiling joists to reach the junction box
on the bottom of the hood support frame.
• Connect the wiring to the house wiring in accordance
with local codes.
Grounding Instructions
The grounding conductor must be connected to
a ground metal, permanent wiring system, or an
equipment-grounding terminal or lead on the hood.
WARNING:
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED.
ATTENTION – POUR DES
RAISONS DE SÉCURITÉ, CET APPAREIL
DOIT ÊTRE CORRECTEMENT MIS À LA TERRE.
Remove house fuse or open circuit breaker before
beginning installation.
Do not use an extension cord or adapter plug with
this appliance. Follow National Electrical Code or
prevailing local codes and ordinances.
Accessory Frames and Duct Covers
• All models are shipped with a support frame and duct
covers for ceilings heights of 7’11" to 8’5".
• Optional accessories include telescoping support
frames and duct covers to reach 8’6” and up to
10’4” ceiling heights.
• Optional accessories must be ordered with the hood
and be on site before final framing and wall finishing.
Mounting the hood without a support frame
The distance between the cooking surface and the
bottom of the hood must be 30" to 36". In situations
where the ceiling is low, the hoods may be secured
directly to the ceiling without the supplied frame.
Use the bottom of the supplied support frame as a
template to locate the mounting holes in the top of the
hood. Use shims on the ceiling joists or cross framing
in the mounting hole locations. This will allow the
mounting screws to engage the recessed keyhole
slots in the top of the hood. See Step 2.
WARNING:
The improper
connection of equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative if
you are in doubt whether the appliance is properly
grounded.
AVERTISSEMENT
Le mauvais branchement du fil de mise
à la terre peut causer un choc électrique. En cas
de doute, consulter un électricien qualifié ou un
technicien pour déterminer si l’appareil est à la terre.
5
Advance Planning
INSTALLATION HEIGHT REQUIREMENTS
Actual
Ceiling
Height
• These vent hoods must be installed 30" min. and 36" max.
above the cooking surface – regardless of the ceiling
height. Therefore, installation height of the hood depends
on the exact ceiling height of the kitchen.
• Accessories are available for ceiling heights 8’6" and up
to 10’4".
10’4"
10’3"
10’2"
10’1"
10’
9’11"
9’10"
9’9"
9’8"
9’7"
9’6"
9’5"
9’4"
9’3"
9’2"
9’1"
9’
8’11"
8’10"
8’9"
8’8"
8’7"
8’6"
8’5"
8’4"
8’3"
8’2"
8’1"
8’
7’11"
Example: Hood installation height with 8 ft. ceilings.
8 ft. Ceiling
8 ft. Ceiling
9"
Supplied
Duct
Cover
5"
Supplied
Duct
Cover
31"
31"
ZV54I
ZV42I
• Both models are shipped with a support frame and duct
cover for 7’11" to 8’5" ceilings.
• If the ceiling height is 7’11", the installation height above
the cooking surface will be 30".
• If the ceiling height is 8’5", the hood installation height
will be 36".
DETERMINE INSTALLATION HEIGHT
1. Measure the exact ceiling height.
2. Review the chart to determine the range of hood
installation heights that can be accomplished
with or without an accessory kit.
30"
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Model ZV42I
Chimney Length at
Hood Installation Height
31" 32" 33" 34" 35" 36"
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
10’4"
10’3"
10’2"
10’1"
10’
9’11"
9’10"
9’9"
9’8"
9’7"
9’6"
9’5"
9’4"
9’3"
9’2"
9’1"
9’
8’11"
8’10"
8’9"
8’8"
8’7"
8’6"
8’5"
8’4"
8’3"
8’2"
8’1"
8’
7’11"
20" for ZV42I
24" for ZV54I
30" Min. and 36" Max.
Ceiling
Height
36"
to
Countertop
ACCESSORIES
ZX42DC10 – Optional Accessory for ZV42I.
ZX54DC10 – Optional Accessory for ZV54I.
Accessories for ceiling heights of 8’6" to 10’4".
Includes telescoping support frames and duct
covers.
6
Order
ZX42DC10
Use Long
Support
and
Duct Cover
Order
ZX42DC10
Use Short
Support
and
Duct Cover
9
9
Use
Supplied
Support
and
Duct Cover
9
9
9
9
9
Model ZV54I
Actual
Chimney Length at
Ceiling
Hood Installation Height
Height 30" 31" 32" 33" 34" 35" 36"
Duct Cover
Duct
Cover
Kit
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
5
5
5
5
5
5
5
Duct
Cover
Kit
Order
ZX54DC10
Use Long
Support
and
Duct Cover
Order
ZX54DC10
Use Short
Support
and
Duct Cover
Use
Supplied
Support
and
Duct Cover
Advance Planning
DUCT FITTINGS
Use this chart to compute maximum
permissible lengths for duct runs to
outdoors.
For best results, use 10" diameter duct.
Note: Do not exceed maximum permissible
equivalent lengths!
Equivalent Quantity Total
Length*
Used
Length
Duct Piece
10" round
to 8" round
Round,
straight
1 ft.
(per foot
length)
90° elbow
8" Dia. 52 ft.
10" Dia. 24 ft.
45° elbow
8" Dia. 31 ft.
10" Dia. 14 ft.
Round
wall cap
with damper
8" Dia. 99 ft.
10" Dia. 41 ft.
Round
roof cap
8" Dia. 136 ft.
10" Dia. 56 ft.
Maximum recommended duct
length for these hoods: 150 feet
Flexible ducting:
If flexible metal ducting is used, all
the equivalent feet values in the table
should be doubled. The flexible metal
duct should be straight and smooth
and extended as much as possible.
Do NOT use flexible plastic ducting.
5 ft.
Note: Any home ventilation system, such as a ventilation
hood, may interrupt the proper flow of combustion air and
exhaust required by fireplaces, gas furnaces, gas water
heaters and other naturally vented systems. To minimize
the chance of interruption of such naturally vented systems,
follow the heating equipment manufacturer’s guidelines and
safety standards such as those published by NFPA and
ASHRAE.
Total Duct Run
Hoods Are Equipped
For 10" Round Duct
*Hoods are supplied with a 10"
round transition. A locally
supplied transition is required
for other sizes.
Note: Outlet on top of hood is
8-1/8" x 8".
* Actual length of straight duct plus duct fitting
equivalent. Equivalent length of duct pieces are
based on actual tests conducted by GE Evaluation
Engineering and reflect requirements for good
venting performance with any ventilation hood.
7
Installation Preparation
TOOLS AND MATERIALS REQUIRED
7/16" Pivoting
hex socket with 4"
and 6" extensions
(NOT SUPPLIED)
Duct tape
Hammer
Wire cutter/stripper
Key Hole Saw
Pencil and tape measure
Electric or battery operated drill
and 3/16", bits, Phillips and Flat
Blade Screwdriver bits.
10" round metal
duct, length to
suit installation.
Safety glasses
Wire nuts
Spirit level
Flashlight
Saber saw
or Sawsall
Phillips and flat blade
screwdrivers
Strain relief for
junction cover.
Step ladder
120V 60Hz. 15 or 20 Amp,
2-wire with ground. Properly
grounded branch circuit.
Pliers
Carpenter’s square
Metal Snips
• Carefully, lay the hood on its side. A support frame is
secured to the inside top of the hood. Remove the
attachment screws at the outside top. Discard screws.
• Grasp the support
frame inside the
hood with both
hands and
carefully rotate out
of the opening.
Be careful not to
scratch the hood.
REMOVE THE PACKAGING
• Remove the parts packages and packing materials.
• Lift the hood out of the box.
IMPORTANT: Lift the hood by grasping
the outside edges of the exhaust opening on the top.
Parts
Parts
Parts
Hood
Motor
Mounted
on Skid
Shipping Carton
• The hood motor is shipped secured to the skid with 4
screws. Locate and remove 2 screws on each side of
the motor. Discard the shipping skid and screws.
• Place the hood on a protective surface to prevent
scratches and damage to the stainless steel finish.
8
Installation Preparation
PARTS PROVIDED
Locate the parts packed with the hood.
Allen Wrench
Transition with Damper
Support frame for 8 ft. ceiling
with 4 large pan head screws
installed on the bottom corners.
Implement rods with standoffs
2-piece decorative duct cover
Duct collar
Decorative top cover
2 Filters (3 with 54" hood)
2 Grease trays (3 with 54" hood)
HARDWARE PACKAGE
ACCESSORY PACKAGE
Locate and check
contents. Screws
shown actual size.
Check accessory package.
Select the taller set for 9’6" to 10’4" ceilings.
Select the shorter set for 8’6" to 9’6" ceilings.
Discard unused set.
Screws A
4 (7/16")
hex head
wood
screws
2 Sets of Duct Covers
Screws B
2 (1/8" x 1-1/2")
Phillips
pan head
screws.
2 Support Frames
with 8 height
adjustment
screws
Screws D
2 small
Phillips
head
screws
2 Templates
Screws C
8 blunt point
Phillips
screws
Screw F
Blower safety screw and lock washer,
Phillips head M 6 x 16.
Note: Hardware appearance may vary slightly.
4 Attachment Screws
Screws E
2 Phillips
head wood
screws
9
Installation Instructions
STEP 1 CONSTRUCT CEILING SUPPORT
Plan the Location of the Hood and Ductwork
• Use a plumb bob to check the location. The
countertop/cooktop below the hood must be centered
with the hood.
• The hood should extend beyond the front and rear edge
of the cooking appliance.
• The duct in the ceiling must be centered over the
cooktop.
Ceiling
Ceiling
Hood
Ducting
Centerline
Hood
Ducting
Centerline
Front
Front
15-7/8"
18-1/8"
36-1/4"
31-3/4"
Align With
Center of
Cooktop
Align With
Center of
Cooktop
Cooktop
Cooktop
Countertop
Countertop
54" Hood Side View
42" Hood Side View
Ceiling Support Structure
• At the hood location, install 2 x 4 cross framing between
ceiling joists as shown. (2x4’s are required to support the
weight of the hood.)
12-3/4” (42” Hood)
17” (54” Hood) Install
Cross-Framing
Symmetrically About
Duct/Cooktop Centerline
EXAMPLE A
16” Joist
Spacing
• Arrange cross framing in the ceiling to suit the existing
structure.
• Your ceiling joists will be like one of the following
examples.
8 5/8”
10” Duct
2x4 Cross
Framing
Front
of
Hood
Align duct
to center of
Cooktop
Top View – Ceiling Joists Parallel to Front of Hood
10
Cooktop
Outline
Installation Instructions
STEP 1 CONSTRUCT CEILING SUPPORT
CONTINUED
12-3/4” (42” Hood)
17” (54” Hood)
Install CrossFraming
Symmetrically About
Duct/Cooktop
Centerline
EXAMPLE B
16” Joist
Spacing
8 5/8”
2x4 Cross
Framing
10” Duct
Front
of
Hood
Align duct
to center of
Cooktop
Cooktop
Outline
Top View – Ceiling Joists Run Perpendicular to Front of Hood
EXAMPLE C
12-3/4” (42” Hood)
17” (54” Hood) Install Cross-Framing
Symmetrically About Duct/Cooktop
Centerline
2x4 Cross
Framing
8 5/8”
10” Duct
16” Joist
Spacing
Front
of
Hood
Align duct
to center of
Cooktop
Cooktop
Outline
Top View – Ceiling Joists at Angle with Front of Hood
11
Installation Instructions
STEP 1 CONSTRUCT CEILING SUPPORT
CONTINUED
• Secure each 2 x 4 block with at least four (4), #10 wood
screws, 3” long (not supplied). Use 8 wood screws
total for the two supports.
2x 4 Min.
Cross Framing
• The cross framing must be accurately aligned to
assure correct positioning of the hood.
• The cross framing must be level in all directions.
Check with a spirit level and adjust if necessary.
Ceiling
Joist
8-5/8"
IMPORTANT: The ceiling structure must be capable of
supporting the weight of the hood (approximately 300
pounds) and any inadvertent user contact loads. The
hood support frame will be supported by the 2 x 4
cross framing.
17"
(54" Hood)
12-3/4"
(42" Hood)
Height
Adjustment
Screw Holes
Ductwork
• Use the shortest and straightest duct route possible.
For satisfactory performance, duct run should not
exceed 150 feet equivalent length for any duct
configuration.
• Refer to “Duct Fittings” chart to compute the maximum
permissible length for duct runs to the outdoors.
• This vent hood must use 10” round rigid duct.
• Install the house ductwork to run horizontally between
ceiling joists or straight up through the roof.
Ceiling Joint
10"
Duct
2x4
Vent Straight Up
Through The Ceiling
Finish the Ceiling
• Finish the ceiling surface. Be sure to mark location of
the ceiling joists and cross framing. Check to be sure
the ceiling is level, use shims if necessary.
12
Installation Instructions
STEP 2 MOUNT TEMPLATE
• Select the template for your hood size.
• Align the template with the marks on the ceiling and
tape in place.
– Be sure the template is oriented correctly,
with the front of the hood.
• Use a plumb to check to be sure the mounting
holes will provide parallel alignment with the
countertop below.
• Center punch all hole locations.
• Drill pilot holes in the 4 screw locations. Use a
3/16” bit and drill approximately 1-1/2” deep.
• Drive 4 Hex head wood screws (Screws A) into
the center of the ceiling joists and cross framing.
Leave a 1/4" gap to allow the screw head to
engage the keyhole slots on the support frames.
• Cut the 10-1/2" duct opening through the sheet
rock.
1/4" Gap
Screws A
STEP 3 SIZE AND INSTALL DUCTWORK
• Measure from house duct flange to bottom of
support frame. Subtract 4-3/8" for clearance to the
bottom of the support frame.
• Cut the 10” duct length to size.
• Secure duct to house ducting with sheet metal screws.
• Seal all connections with duct tape.
• Attach the duct collar loosely, about 1" from the bottom
of the duct using Screws B.
House
Duct
Duct
Duct
Length
Duct
Collar
Screws B
13
4-3/8" Clearance
to Bottom of Frame
Installation Instructions
STEP 4 INSTALL ACCESSORY (OR SUPPLIED) SUPPORT AND DUCT COVERS
Install Small Pan Head
Screws on Each Side
Top Duct
Cover
Install
Safety Screw
on Each Side
Screws D
Bottom Duct
Cover
Adjust
Frame to
nstallation
Height
Install Stop
Screw
Screws E
Stop Screw
Storage Location
Install supplied support frame OR telescoping
accessory frame
CAUTION:
The stop screw
must be installed. Failure to do so could result in
personal injury or damage to the duct cover. The stop
screw will prevent the lower duct from sliding down
while completing the installation.
• Hang the supplied support frame or telescoping
accessory frame to the ceiling joists and cross framing
on the 4 hex head screws by engaging the keyhole slots
on the frame.
• Check to be sure the support frame is level, vertically
and horizontally.
• Tighten the hex head screws securely.
• Install safety screws, (Screws E) on each side of the
frame.
PRUDENCE
Il faut mettre en place la vis de butée afin d’éviter des
blessures ou d’endommager l’enceinte du conduit. La vis
de butée empêche l’enceinte inférieure du conduit de
descendre pendant l’installation.
Adjust telescoping accessory frame to length
• Remove the 8 frame adjustment screws. Adjust the
lower support up or down to the pre-determined length.
Reinstall and securely tighten the 8 adjustment screws.
• Slide the top (inner) accessory duct cover up and over
the frame. Secure the duct cover to the frame as shown
using Screws D.
• Locate and remove the safety stop screw. Slide bottom
duct cover up and over the top duct cover. Align bottom
duct screw hole to the hole in the frame. Hold the duct
cover in place while installing screw.
Secure house wiring
• Route house wiring through the ceiling and pull a length
to reach the hood junction box, approximately 6” below
the support. Tape to the right side of the support frame.
IMPORTANT: Again, check to be sure the support is
level in both directions. There is no way to level the hood
after the hood is secured to the frame.
14
Installation Instructions
STEP 5 INSTALL DUCT TRANSITION
WITH DAMPER
STEP 6 INSTALL HOOD
Note: THREE PEOPLE ARE REQUIRED TO
COMPLETE THIS INSTALLATION!
Bumper Pads
Duct
Transition
1/4" Gap
Attachment
Screws
Attachment
Keyholes
Screws C
IMPORTANT: Remove shipping tape from damper and
check that damper moves freely.
• Place the transition piece over the hood exhaust and
secure with 4 Screws C provided.
• Use duct tape to seal the connection. Check to be
sure the damper moves freely.
• Back out the hanging screws on the bottom of the
support frame to a 1/4" gap.
• Lift the hood up to the support frame. Carefully align
the hood keyhole to the screws on the support frame.
Slide the hood to engage the keyhole slots.
• Tighten the screws.
Install
2 Safety
Screws
Screws C
• Install safety screws into the top of the hood as
shown.
• Check hood level in both directions.
STEP 7 CONNECT DUCT
• Loosen duct collar and slide
down to cover gap between
transition and house duct.
Tighten collar
screws and tape all joints.
• Seal all connections with duct
tape.
Slide Duct
Collar Down
to Cover Gap
Note: Do not drive screws through this duct
connection. Doing so will prevent proper damper
operation.
15
Installation Instructions
STEP 8 CONNECT ELECTRICAL
Verify that power is turned off at the source.
• Install strain relief onto the knockout of the junction
box.
• Insert house wiring through strain relief and tighten.
• Use wire nuts to connect incoming ground to green,
white to white and black to black.
• Push wires into junction box and replace cover. Be sure
wires are not pinched.
WARNING:
If house wiring is not
2-wire with a ground wire, a ground must be provided
by the installer. When house wiring is aluminum, be
sure to use UL approved anti-oxidant compound and
aluminum-to-copper connectors.
ATTENTION – Si le câblage de la
maison n’est pas du type à deux fils avec un fil de
terre, l’installateur doit fournir un circuit de terre.
Quand les fils de la maison sont en aluminium, il
prendre soin d’utiliser de la pâte antioxidation
approuvée par UL et des connecteurs pour
l’aluminium-cuivre.
STEP 9 INSTALL THE MOTOR
Top
IMPORTANT: Connector
ends are designed to
mate only one way.
Match flat and round
connectors as shown.
Outlet
Attachment
Slot
Spring
Clip
Attachment Screw
and Washer
Screw F
Attachment
Slot
Spring
Clip
Junction Box
• From the inside of the hood, slip motor into the
attachment slot on the left.
• Rotate motor upwards until it snaps into the spring
clip on the right.
• Secure the motor to the hood with the machine
screw and lock washer (Screw is marked with red
paint.)
• Plug blower cable into the connector on the blower.
• Plug cable at the top of the hood into the junction box
connector. Route cable so it won’t be pinched or
damaged when the duct cover is lowered.
16
Installation Instructions
STEP 10
SLIDE DUCT COVER
DOWN
STEP 12 INSTALL RODS
• Use a flat blade screwdriver to install stand-offs into
the bottom of the hood.
• Align implement rod to stand-offs with the screw hole
towards the inside of the hood. Secure the rod to the
stand-offs with the supplied Allen wrench.
• Follow the same procedure on the opposite side.
SKIP THIS STEP IF USING THE SUPPLIED DUCT
COVER
• Hold the duct cover in place and remove the
temporary stop screw. Return the screw to the
storage location for future use.
• Slide the lower duct cover down onto the hood.
Slide
Duct
Cover
Down
Remove
Stop
Screw
Screw
Stand-offs
Into Hood
Stop Screw
Storage Location
Use Allen
Wrench to
Secure Rod
to Stand-offs
STEP 11 INSTALL FILTERS
• Place filter drip trays into the rear of the hood.
• Insert the filter into the upper opening and drop into
the trays.
• To remove the filters, grasp the knobs and push the
filter up and lift out.
17
Installation Instructions
STEP 14 FINALIZE INSTALLATION
STEP 13 INSTALL SUPPLIED DUCT
COVER AND TOP COVER
• Check all lamps to assure tightness in sockets.
• Turn power on at the circuit breaker.
• Refer to the Owner’s Manual for operating and
cleaning instructions.
Install Duct
Cover Screw
on Each Side
Screws D
• Install the supplied 2-piece duct cover over the
support frame (if using supplied frame). Snap ends
together.
• Secure duct covers to support frame with 2
Screws D.
• For a more finished appearance, a top cover is
supplied and should be installed whenever the top of
the hood is visible.
TIP: Place pieces
of tape over ends
of the cover to
prevent scratching
the duct cover.
Remove tape
before installing
screws.
Tape
Tabs
• Engage tabs into slots on each side at the top of the
hood. The covers should lay flat in the impression on
top of the hood.
Top Cover
Screws C
Install Screws
Front and Back
• Install 2 Screws C to secure the cover to the hood at
the front and back.
18
Installation Instructions
STEP 15 INSTALLATION CHECKLIST
Check Blower Safety Screw
■ Ensure that blower safety screw is securely tightened.
See page 16, Step 9. If screw is missing, order
replacement parts bag.
Check appearance and installation
■ Use a spirit level to check that the hood is level.
Review installation instructions to determine source
of problem.
■ Top covers (if used) should lay flat in the recess on
top of the hood. Make sure side tabs are engaged in
slots and the cover is secured with two screws.
Check Operating Sound and Proper Air-Flow
■ Turn blower to each speed setting and listen for rattles
and vibration. You should notice an audible difference
at each speed setting.
■ Clean the hood surfaces and all filters. See the
Owner’s Manual for cleaning instructions. They
should be free of construction debris such as
sawdust.
■ Check for foreign material in transition.
■ Check that blower screen is not damaged or pushed
into the blower impeller.
■ The damper should move freely. Listen for opening and
closing while turning the unit on and off.
■ Check that the damper is not damaged, does not
vibrate and that damper bumper pads are in place.
Order a damper replacement assembly if needed.
■ Check that ductwork is 10" round. If duct type is not
rigid and less than 10" round, inform the consumer that
performance will be reduced.
Check Lighting Function
■ Check that power cable is plugged into the junction
box on top of the hood.
■ Turn halogen lamps to each setting. Note change in
brightness at different settings.
■ Check that each lamp bezel is secure. Turn to the right
to tighten. Order replacement lamp bezel and socket
assemblies if needed.
19
Note: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram® local service in your area, call
1.800.444.1845.
Note: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
GE Consumer & Industrial
Pub. No. 49-80209-3
01-08 JR
Appliances
General Electric Company
Louisville, KY 40225
ge.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement