or email [email protected]
7W LED Energy Saver
Bulkhead Light
Model: LEDBHR7W – Silver
1
1. General Information
Parts Included:
• Luminaire unit.
• Instruction manual. Please keep safe for future reference.
• Accessory pack.
Tools & Parts Needed:
• Electric drill and bits.
• Terminal or electricians screw driver.
• Flat and Philips screw driver.
• Wire cutters.
2. Selecting the Location:
The unit is for outdoor use. The unit must be mounted on a non-flammable surface as a fixed luminaire, and is not suitable for portable use.
The unit can get very hot during use. Ensure the unit has cooled before handling. Ensure adequate ventilation space is allowed between the unit and any object above, in front, or to either side of the unit. Suggested space is 0.5m above, 0.3m to either side, and 1.0m in front.
2
3. Installation
After choosing a suitable location (see previous section) install the unit as follows:
*** IMPORTANT ***
Switch off electricity at the fuse box by removing the relevant fuse or switching off the circuit breaker before proceeding with the installation.
We recommend that this unit be fitted by a qualified electrician. Install in accordance with wiring and current building regulations.
Please read the instructions carefully.
The unit is suitable for connection to a 230V AC 50Hz electricity supply.
It is suggested that 3 core round flexible cable of 1mm 2 gauge is used.
An isolating switch should be installed to switch the power to the unit ON/OFF.
Remove the front of the unit, by undoing the 4 Philips screws.
Remove the bezel, and the lens (with gasket). The mounting holes should now be visible. Mark the position of the mounting holes on the wall, and drill the holes for the wall plugs. Undo the cable gland sufficiently to allow the cable to be pushed through from the back.
Leave enough slack to allow for wiring, re-tighten the cable gland, and screw the unit to the wall using the screws and seals provided.
It is important to use the seals to maintain the IP rating.
Connect the earth wire to the earth terminal on the back case, and live and neutral to the two way terminal block. Secure the cable using the cable clamp.
Reposition the lens over the unit, taking care to ensure the gasket is in place. Put the bezel over the lens, and re-tighten the 4 Philips screws.
3
4. Connection
Live (brown)
Neutral (blue)
Earth (green/yellow)
Ensure all connections are secure.
L
N
5. Operation
Turn the power to the isolating switch on. Use the isolating switch to turn the unit on, and it will illuminate.
6. Technical Speciļ¬ cations
Energy effi ciency
Energy usage
Class A
8.4KwH/1000H
4
Lamp beam angle
Power supply
Lamp type
Environmental protection
EC directives
Dimensions
Mounting hole centres
120 degrees
The lamps are not replaceable in this product
230 V AC 50 Hz
7W LED which is the equivalent of 40W halogen lamp.
IP65
Conforms to current EC directives
135mm x 135mm x 59mm
88mm
If you experience problems, do not immediately return the unit to the store.
Telephone the Timeguard Customer Helpline 020 8450 0515
Qualifi ed Customer Support Co-ordinators will be on-line to assist in resolving your query.
3 Year Guarantee
In the unlikely event of this product becoming faulty due to defective material or manufacture, within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For years 2 to 3 or any difficulty in the first year, telephone our helpline on 020 8450 0515.
Note: a proof of purchase is required in all cases. For all eligible replacements (where agreed by Timeguard) the customer is responsible for all shipping/postage charges outside of the UK. All shipping costs are to be paid in advance before a replacement is sent.
For assistance with this product please contact:
HELPLINE
020 8450 0515 or email [email protected]
5
For a product brochure please contact:
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Offi ce: 020 8452 1112 or email [email protected]
67-058-508 (Iss.1)