Catalogue Sheet: PREP Series

Catalogue Sheet: PREP Series
Project/Location:
Contractor:
Premier™ Series
Date:
Thermoplastic Pictogram
Combination Unit
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
The PremierTM Series of combination units (unit equipment and
pictogram exit sign) are designed to complement designer’s look and
ease of installation with performance and cost-competitiveness.
• O ne-pack combination of battery unit and Pictogram Sign,
a compact and contemporary design
Supply and install the Emergi-Lite® Premier™ Series combination
of unit equipment and pictogram exit sign. The unit frame and
face plates shall be made of injection-molded thermoplastic.
The faceplates shall feature a uniformly illuminated legend. The
light source shall be long-life white light-emitting diodes (LED).
The unit shall be equipped with two emergency heads with tool-less
adjustable swivels and long-life MR-16 LED lamps of
V and
W. Each lamp shall be protected by a snap-on, shock-absorbent,
transparent polycarbonate cover.
• D urable injection-molded thermoplastic housing with
push-to-snap design
• Available in single or double face configurations both with
means for ceiling mounting
The AC input voltage shall be standard 120/347VAC 60Hz. The unit
shall be equipped with a test switch and a green pilot light, located on
the face plate above the pictogram legend. The battery charger shall
be driven by a micro-controller. All electronic circuitry (charger, LED
driver, signage LED’s) shall be installed on a single printed circuit
board PCB. The unit equipped with self-testing / self-diagnostic
features shall automatically self test for one minute every 30 days,
10 minutes in the 6th month and 30 minutes annually. When a fault
is detected, the bi-color pilot-light shall turn from green to red and
shall flash following a particular code. The code description shall
be displayed on a label next to the pilot light to identify the failure
type: battery, charger circuitry, LED lamps for signage, or emergency
lights.
• Supplied standard with two (single face) or three pictogram films
(universal face) for direction selection
• Two MR16 LED or halogen lamps, shielded by a clear
polycarbonate cover
• Twin LED lights provide up to 89 feet of egress illumination on a
6-foot wide path
• S ealed, maintenance-free, Lead-Calcium or
Nickel-Metal-Hydride batteries
• Remote load capacity: one unit equipment with LED remote lights
covers up to 712 feet (217m) of egress illumination
• Remote load capacity up to 92W when using LED lamp option
The combination unit shall meet or exceed the standard CSA C22.2
No.141-10.
• Dual voltage input: 120/347VAC or 120/277VAC
• Comes standard with non-audible auto-diagnostics
The Pictogram combo unit shall be Emergi-Lite ® Model:
.
• Optional vandal-resistant shield with tamper-proof screws
• Certified CSA C22.2 No.141
WIRE GUARDS
• O ptional: Nexus® Compatible
460.0078-E
Wall Mount
PREMIER™ FAMILY
Premier™ Exit Series
Premier™ Combo Series
Premier™ Battery Series
P. 55
P. 56-57
P. 116-117
POWER CONSUMPTION
MODEL
Pictogram Sign Module
L2
L5
AC SPECS
120/347VAC
Less than 4W
120/347VAC
0.12/0.04 A
L5A
H5A
H10A
120/347VAC
0.24/0.08 A
WATTAGE CAPACITY
30MIN
1H00
1H30
2H00
4H00
-
-
-
-
-
25
15
12
8
-
50
30
24
16
8
50
30
24
16
8
50
36
24
18
9
100
72
48
36
18
58
Project/Location:
Contractor:
Premier™ Series
Date:
Thermoplastic Pictogram
Combination Unit
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
11-1/4” [28.7 cm]
12-3/8” [31.5 cm]
4-7/8” [12.3 cm]
< PICTO
LEFT FROM HERE
PICTO
STRAIGHT FROM HERE
PICTO >
RIGHT FROM HERE
17” [43.2 cm]
3-3/8” [8.5 cm]
ORDERING INFORMATION
SERIES
COLOUR
VOLTAGE
POWERPACK
PREP1= single
face
ceiling
or wall
mount
PREP2= double
face
ceiling
mount
PREP1N= single
face
wall
mount
(less
canopy)
PREPU= universal,
2 faces
backplate
and
canopy
W= factory
white
B= black
2= 120/277VAC
3= 120/347VAC
-L2= 6V-25W
LeadCalcium
-L5= 6V-50W
LeadCalcium
-L5A= 12V-50W
LeadCalcium
-H5A= 12V-50W
NiMH
-H10A= 12V-100W
NiMH
CHARGER TYPE
Blank= autodiagnostics,
non audible
U= a
uto-diagnostics,
audible
NEX= NEXUS® system
interface
NEXRF= wireless
NEXUS®
system
interface
OPTIONS
Blank= no options
D3= time delay (15 minutes)
TP= tamper-proof screws*
VRTP1= polycarbonate
shield with tamperproof screws,
single face*
VRTP2= polycarbonate
shield with tamperproof screws,
double face*
*091957-E= t amper-proof bit
(sold seperately)
*VRTP1 & VRTP2 not available
with PREPU.
EXAMPLE: PRE1W3-L2/2MI
59
# OF
HEADS
HEAD STYLE/
WATTAGE
/0= no
heads
/2= two
heads
LA= MR16 LED,
6V-4W
LG= MR16 LED,
12V-4W
LI= MR16 LED,
12V-5W
LJ= MR16 LED,
12V-6W
MI= MR16
halogen,
6V-6W
MJ= MR16
halogen,
6V-10W
MO= MR16
halogen,
12V-10W
MK= MR16
halogen,
12V-12W
MG= MR16
halogen,
12V-20W
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement