Quick Reference Guide (Download PDF, 1M)

Quick Reference Guide (Download PDF, 1M)
2014 Infiniti Q60
1276473_14a_Q60_Convertible_QRG_062113.indd 2
Quick Reference Guide
6/21/13 3:30 PM
Behind
steering
wheel
01
02 Behind
steering
wheel
03
04
05
17
06
Behind
07 steering
wheel
08
09
Behind
11 12 13 steering
10
Behind
steering
wheel
18
wheel
14
Behind
steering
wheel
15
16
19
20
21
22
21
01 INSTRUMENT BRIGHTNESS CONTROL*
12 TRUNK RELEASE SWITCH
02 TRIP COMPUTER SWITCHES
13 rear sonar system switch*
03 HEADLIGHT AND TURN SIGNAL CONTROL
14 TILT AND TELESCOPIC STEERING COLUMN*
04 LOW TIRE PRESSURE WARNING LIGHT
15 INTELLIGENT KEY PORT
05 vehicle information display
16 HOOD RELEASE*
06 WINDSHIELD WIPER and WASHER SWITCH
17 CONTROL PANEL DISPLAY
07 TRIP A/B RESET BUTTON*
18 AUDIO SYSTEM
08 STEERING WHEEL SWITCHES FOR
AUDIO* / BLUETOOTH®
19 AUTOMATIC CLIMATE CONTROLS
09 CRUISE CONTROL
10 PUSH BUTTON IGNITION SWITCH
11 VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH*
20 FRONT PASSENGER AIR BAG STATUS LIGHT*
21 CLIMATE CONTROLLED SEAT SWITCHes*
ARD TOP OPEN / CLOSE SWITCH
22 H
(Convertible models)
*See your Owner’s Manual for information.
1276473_14a_Q60_Convertible_QRG_062113.indd 3
6/21/13 3:30 PM
table of contents
essential information
Tire Pressure Monitoring System (TPMS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Loose Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Fuel-Filler Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Automatic Power Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Accessing the Front Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
first drive features
INFINITI Intelligent Key System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Trunk Lid Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Seat Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Automatic Drive Positioner (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . 6
Seat Belt Guide (Convertible models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Passenger Rear Seat Entry/Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Outside Mirror Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Starting/Stopping the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Headlight Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Windshield Wiper and Washer Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Automatic Climate Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FM/AM/SiriusXM Satellite Radio With CD/DVD Player
(with Navigation System) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . 11
USB/iPod® Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Conventional (Fixed Speed) Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . 12
Intelligent Cruise Control (ICC) System (if so equipped) . . . . . . . . . . . . . . 13
Opening/Closing the Hard Top (Convertible models) . . . . . . . . . . . . . . . . . 14
system guide
Trip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Bluetooth® Hands-free Phone System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
System Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Bluetooth® System with Navigation (if so equipped) . . . . . . . . . . . . . . . 16
Bluetooth® System without Navigation (if so equipped) . . . . . . . . . . . . 18
Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DVD Player (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
HomeLink® Universal Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
• A cellular telephone should not be used for any purpose while
driving so full attention may be given to vehicle operation.
• Always wear your seat belt.
• Supplemental air bags do not replace proper seat belt usage.
• Children 12 and under should always ride in the rear seat
properly secured in child restraints or seat belts according to
their age and weight.
• Do not drink and drive.
For more information, refer to the “Safety –– Seats, seat belts and
supplemental restraint system (section 1)”, “Monitor, climate,
audio, phone and voice recognition systems (section 4)” and the
“Starting and driving (section 5)” of your Owner’s Manual.
Additional information about your vehicle is also available
in your Owner’s Manual, Navigation System Owner’s Manual
and at www.InfinitiUSA.com.
1276473_14a_Q60_Convertible_QRG_062113.indd 4
To view detailed
instructional videos, go to
www.infinitiownersinfo.mobi/2014/q60
or snap this barcode with an
appropriate barcode reader.
6/21/13 3:30 PM
essent i al i n f o r m a t i o n
Tire Pressure Monitoring System (TPMS)
A Check tire pressure warning message will
appear in the vehicle information display 01 and
the low tire pressure warning light 02 will illuminate
when one or more tires are low on pressure and air
is needed.
01
•The tire pressures should be checked when
the tires are cold. The tires are considered cold
after the vehicle has been parked for 3 hours
or more or driven less than 1 mi (1.6 km) at
moderate speeds.
After tire pressures are adjusted, drive the vehicle
at speeds above 16 MPH (25 km/h). The CHECK
TIRE PRESSURE warning message and low tire
pressure warning light will disappear.
02
When the low tire pressure warning light flashes for 1 minute and then remains on, the TPMS
is not functioning properly. Have the system checked by an INFINITI retailer.
Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the
outside temperature. Low outside temperature can lower the temperature of the air inside
the tire, which can cause a lower tire inflation pressure. This may cause the low tire pressure
warning light to illuminate. If the warning light illuminates, check the tire pressure in your tires.
• Check the tire pressure (including the spare tire) often and always prior to long distance trips.
The Tire and Loading Information label contains valuable information. Please refer to section
9, “Technical and consumer information”, in your Owner’s Manual for the location of the Tire
and Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and
the“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.01
Loose Fuel Cap
A LOOSE FUEL CAP warning message will appear in
the vehicle information display 01 when the fuel-filler
cap is not tightened correctly.
To tighten, turn the cap clockwise until a single click
is heard.
01
The warning message will disappear when the vehicle
detects the fuel-filler cap is properly tightened and the
reset button 02 is pressed for about 1 second.
If the cap is not properly tightened, the Malfunction
Indicator Light
may illuminate.
For more information, refer to the “Instruments and controls (section 2)” and
the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
02
2
1276473_14a_Q60_Convertible_QRG_062113.indd 2
6/21/13 3:30 PM
Fuel-Filler Door
The fuel-filler door is located on the passenger’s side of
the vehicle.
Unlock the fuel-filler door using one of the following
operations, then push and release the left side of the
door to open.
•Push the door handle request switch while
carrying the INFINITI Intelligent Key with you.
• Press the UNLOCK button on the Intelligent Key.
• Push the power door lock switch to the UNLOCK position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Automatic Power Windows
Your power windows have an automatic adjusting
function to ensure windows close completely to help
seal against wind noise and weather leaks.
When the front doors are being opened, the windows
automatically lower slightly to avoid contact between
the windows and the side roof panels.
If your vehicle’s battery is discharged or
disconnected, your power window automatic
function will not operate.
Refer to your Owner’s Manual for information to
initialize your power window system.
If the power window functions do not operate
properly after initializing the system, have your
vehicle checked by an INFINITI retailer.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
Accessing the Front Cup Holders
To open the cup holders, push the lid 01 down
and release.
01
The flap 02 will fold down when inserting a
large container.
For more information, refer to the “Instruments and controls (section 2)” of
your Owner’s Manual.
02
3
1276473_14a_Q60_Convertible_QRG_062113.indd 3
6/21/13 3:30 PM
f i rst dr i v e f e a t u r e s
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or
unlock the vehicle, open the trunk and start the engine.
It is important to make sure the Intelligent Key is
with you (that is, in your pocket or purse).
01
The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.
To lock the vehicle, push either door handle request
switch 01 once or press the button 02 on the key fob.
To unlock the vehicle, perform one of the following procedures:
•Push either door handle request switch 01 once; the
corresponding door will unlock. Push the door handle
request switch 01 again within 1 minute; all other doors
will unlock, or
02
03
•Press the button 03 on the key fob to unlock the driver’s
side door. Press the button again; all other doors will unlock.
04
To release the trunk lid, press the HOLD button 04 for more than
1 second. Lift the trunk lid to access the trunk.
05
To retract the hard top (Convertible models), push and hold the
door handle request switch 01 until the hard top is fully open.
The Intelligent Key can also be used to activate the panic alarm by pressing and holding the
button 05 for more than 1 second. Once activated, the panic alarm and headlights will
stay on for a period of time.
INFINITI INTELLIGENT KEY BATTERY DISCHARGE
If the battery in the Intelligent Key is almost
discharged, the guide light 06 of the Intelligent
Key port blinks and the Intelligent Key battery
discharge indicator 07 is displayed in the vehicle
information display.
To start the engine under these circumstances, insert
the Intelligent Key into the key port with the buttons
facing upward and the key ring end toward you until
it latches into place. Then push the ignition switch to
start the engine.
06
07
To remove the Intelligent Key from the port, push the
ignition switch to turn the engine off and then pull the
Intelligent Key out of the port.
The Intelligent Key port does not charge the Intelligent Key battery. If you see the low battery
indicator 07 , replace the battery in the Intelligent Key.
Do not insert the mechanical key or any other objects into the key port because it will
damage the key port.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
4
1276473_14a_Q60_Convertible_QRG_062113.indd 4
6/21/13 3:31 PM
Trunk Lid Release
Use one of the following methods to open the trunk:
Push the trunk open request switch 01 for more
than one second while carrying the INFINITI
Intelligent Key with you.
01
Press the trunk button HOLD on the Intelligent Key for
more than one second.
Push down on the trunk lid release switch 02
located on the instrument panel to the left of the
steering wheel.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
02
Seat Adjustments
To slide the seat forward or backward, push the
01 forward or backward.
control switch
To recline the seatback, push the switch
forward or backward.
02
SEAT LIFTER
01
02
To adjust the angle of the front seat cushion or height
of the seat, push the front or rear end of the switch
01 up or down.
03
POWER LUMBAR SUPPORT (driver’s seat)
To adjust the seat lumbar support, push the front or back end of the switch
03 .
For more information, refer to the “Safety –– Seats, seat belts and supplemental restraint system (section 1)” of your
Owner’s Manual.
5
1276473_14a_Q60_Convertible_QRG_062113.indd 5
6/21/13 3:31 PM
f i rst dr i v e f e a t u r e s
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner memory.
Follow these procedures to set the memory positions:
•Confirm the shift lever is in the P (PARK) position
(automatic transmissions) or the parking brake is applied (manual transmissions).
• Push the ignition switch to the ON position.
•Adjust the driver’s seat, steering column and outside mirrors to the desired positions using
the adjusting switches for each feature.
•Push the SET switch and within 5 seconds, push the memory switch (1 or 2) for at least 1 second.
•The indicator light on the memory switch you select will illuminate for approximately 5 seconds.
• The driver’s seat, steering column and outside mirror positions are now set to your preference.
These memorized positions can also be linked to your INFINITI Intelligent Key.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Seat Belt Guide (Convertible models)
Unsnap the seat belt guide 01 to allow rear seat
passengers easier access.
Before fastening the seat belt, ensure the seat belt is
inserted into the seat belt guide and the snaps are
securely fastened.
When using the seat belt guide, do not allow the seat
belt to twist so that it will retract correctly.
01
For more information, refer to the “Safety –– Seats, seat belts and supplemental restraint system (section 1)” of your Owner’s Manual.
Passenger Rear Seat Entry/Exit
For ease in entering and exiting the rear passenger
areas of the vehicle, perform the following steps:
1.Release the front seatbelt guide and seat belt.
(Convertible models)
2.Pull the seatback lever 01 upward to fold the
front seatback forward. Make sure that the front
seatback is completely folded.
01
02
Convertible
02
01
3.To slide the front seat forward, firmly push
Coupe
the seatback button 02 . The front seat will
move forward.
To stop the front seat from sliding, press the seatback button 02 again.
To return the front seat to its original position:
1. Push or pull the seatback backward until it locks in place.
2. Press the seatback button 02 to slide the front seat backward.
For more information, refer to the “Safety –– Seats, seat belts and supplemental restraint system (section 1)” of your
Owner’s Manual.
6
1276473_14a_Q60_Convertible_QRG_062113.indd 6
6/21/13 3:31 PM
Outside Mirror Control Switch
To select the right or left side mirror, turn the control
switch 01 right or left.
To adjust the mirror angle, move the control switch
01 up, down, right or left.
01
To prevent accidentally moving the mirror, turn and
set the switch to the middle (neutral) position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Starting/Stopping the Engine
AUTOMATIC TRANSMISSION (if so equipped)
It is important to make sure the INFINITI Intelligent
Key is with you (that is, in your pocket or purse).
Depress the brake pedal.
•If the brake pedal is not depressed, pushing the
ignition switch once enters the ACC mode.
•If the ignition switch is pushed a second time, the
vehicle will enter the ON mode.
Press the ignition switch START/STOP button to start
the engine.
MANUAL TRANSMISSION (if so equipped)
Depress the brake pedal.
•If the brake pedal is not depressed, pushing the ignition switch once enters the ACC mode.
• If the ignition switch is pushed a second time, the vehicle will enter the ON mode.
Move the shift lever to N (NEUTRAL).
Depress the clutch pedal to the floor.
Press the ignition switch START/STOP button.
TURNING THE ENGINE OFF
For an automatic transmission, move the shift lever to the P (PARK) position, apply the
parking brake and push the ignition switch.
For a manual transmission, apply the foot brake, place the vehicle in 1st gear, apply the
parking brake and push the ignition switch.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
7
1276473_14a_Q60_Convertible_QRG_062113.indd 7
6/21/13 3:31 PM
f i rst dr i v e f e a t u r e s
Headlight Control Switch
HEADLIGHT CONTROL
Turn the headlight control switch to the
position 01 to turn on the front parking, side
marker, tail, license plate and instrument panel
lights. Turn the switch to the position 02 to turn on
the headlights.
03
01
02
AUTOLIGHT SYSTEM
The autolight system will automatically turn the headlights on when it is dark and off when
it is light. The system will keep the headlights on for a period of time after you turn the
ignition off and all doors are closed.
To activate the autolight system, turn the headlight control switch to the AUTO position 03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
01 or
control switch to the OFF,
position 02 .
HIGH BEAM SELECT
Push the headlight control switch forward 04 to
select the high beam function. The blue indicator
light
illuminates in the instrument panel. Pull
the headlight switch back to the original position to
select the low beam. The blue indicator light goes off.
04
05
Pull and release the headlight control switch 05 to
flash the headlight high beams on and off.
FOG LIGHT SWITCH
The headlights must be in the auto, or the low
selected for the fog lights to operate.
beams
Turn the switch (inside collar) to the
to turn the fog lights on.
position 06
06
Turn the switch (inside collar) to the OFF position to
turn the fog lights off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
8
1276473_14a_Q60_Convertible_QRG_062113.indd 8
6/21/13 3:31 PM
Windshield Wiper and Washer Switch
Move the lever to the following positions to operate
the windshield wipers:
03
MIST 01
01 Mist (MIST) - One sweep operation of the wipers.
02 Intermittent (INT) - Wipers operate intermittently
and vary in accordance with vehicle speed. The
intermittent operation speed can be adjusted
by twisting the time control ring 03 toward you to
decrease wiper delay.
OFF
INT 02
LO 04
HI 05
04 Low (LO) - Wipers operate at a continuous
low-speed.
05 High (HI) - Wipers operate at a continuous
high-speed.
06 Pull the lever toward you to activate the washer.
The wipers will operate several times.
06
RAIN-SENSING AUTO WIPER SYSTEM (if so equipped)
The rain-sensing auto wiper system can automatically turn on the wipers and adjust the
wiper speed depending on the rainfall and the vehicle speed.
To set the rain-sensing auto wiper system, push the lever down to the AUTO (if so equipped)
position 02 . The wiper will sweep once while the ignition switch is in the ON position.
The rain sensor sensitivity level can be adjusted by turning the time control ring 03 toward
the front (high sensitivity) or toward the rear (low sensitivity).
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
08
04
05
03
01
09
02
06
07
Automatic Climate Controls
01 AUTO BUTTON/DRIVER’S SIDE TEMPERATURE CONTROL DIAL
The auto mode may be used year-round. Press the AUTO button to turn the system on
and the system will automatically control the inside temperature (automatic cooling and
or dehumidified heating), air flow distribution and fan speed.
Turn the driver’s side temperature control dial to the left for cooler air or right for warmer air.
02 DUAL BUTTON/PASSENGER’S SIDE TEMPERATURE CONTROL DIAL
Press the DUAL button to turn the passenger’s side temperature controls on or off. This
will allow the passenger’s side temperature to be adjusted independently from the
driver’s side by turning the passenger’s side temperature control dial.
Turn the passenger’s side temperature control dial left for cooler air or right for warmer air.
9
1276473_14a_Q60_Convertible_QRG_062113.indd 9
6/21/13 3:31 PM
f i rst dr i v e f e a t u r e s
03 FAN SPEED CONTROL BUTTONS
To manually adjust the fan speed, press the top
button to increase the fan speed or
press the bottom
button to decrease the fan speed.
04 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Press the defroster control button
to turn the system on. The A/C automatically turns
on when the defroster mode is selected. This feature removes humidity from the air.
Turn the temperature control dial 01 to set the desired temperature.
To defrost the front and side windows, set the temperature controls and fan speed
controls to their maximum settings.
05 MODE BUTTON
Press the MODE button to cycle through the following air flow outlets:
Air flows from the center and side vents.
Air flows from the center, side and foot vents.
Air flows mainly from the foot vents.
Air flows from the defroster and foot vents.
06 DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS
Push the rear window defroster switch
This function automatically turns off after approximately 15 minutes.
to turn the system on or off.
07 INTAKE AIR CONTROL BUTTON
AIR RECIRCULATION
Press the intake air control button to recirculate interior air inside the vehicle. The
indicator light on the
side will come on. This system is used to avoid outside odors
and helps to adjust the inside vehicle temperature more effectively.
The air recirculation mode cannot be activated when the air conditioner is in the front
defrosting mode
or front defrost and foot vent mode .
.
OUTSIDE AIR CIRCULATION
Press the intake air control button to draw outside air into the passenger compartment.
The indicator light on the
side will come on.
AUTOMATIC INTAKE AIR CONTROL
In the auto mode, the intake air will be controlled automatically. To manually control the
intake air, press the intake air control button. To return to the automatic control mode,
press the intake air control button for about 2 seconds.
08 A/C BUTTON
Press the A/C button to turn the air conditioner system on or off. This system helps cool
and dehumidify the air inside the cabin and defog the windows.
09 OFF BUTTON
Press the OFF button to turn the climate control system off.
For more information, refer to the “Instruments and controls (section 2)” and the “Monitor, climate, audio, phone and voice
recognition systems (section 4)” of your Owner’s Manual.
10
1276473_14a_Q60_Convertible_QRG_062113.indd 10
6/21/13 3:31 PM
05
02
01
03
04
FM/AM/SiriusXM* Satellite Radio with CD/DVD Player
(with Navigation System) (if so equipped)
01 VOLUME/ON•OFF CONTROL KNOB
Press the VOL/ON•OFF control knob to turn the system on or off. Turn the knob right or
left to increase or decrease the volume.
02 SEEK•CAT AND TRACK BUTTONS
To scan quickly through each broadcasting station, press the SEEK•CAT button or the
TRACK button to stop at the previous or next broadcast station.
For SiriusXM Satellite Radio, press the SEEK•CAT button or the TRACK button to switch to the first channel of the previous or next category.
Press the SEEK•CAT button or the TRACK button to change tracks on a CD.
Press and hold the SEEK•CAT button or the TRACK button to fast forward or rewind a
track on a CD.
03 TUNE/FOLDER/AUDIO CONTROL KNOB
To manually tune the radio, turn the TUNE/FOLDER/AUDIO knob left or right.
04 STATION PRESET BUTTONS
Twelve stations can be set for the FM band, six for the AM band and eighteen for
SiriusXM Satellite Radio.
To store a station in a preset, you must first select a radio band by pressing the AM•FM/
SAT button 05 , then tune to the desired AM, FM or SiriusXM Satellite Radio station.
Then press and hold the desired station preset button (1-6) until the preset number is
updated on the display and the sound is briefly muted. The channel indicator will then
display and the sound will resume. Programming is now complete.
To retrieve a previously set station, select the radio band where the preset was stored,
then press the corresponding station select button (1-6).
*SiriusXM Satellite Radio is only available on vehicles equipped with optional SiriusXM Satellite Radio subscription service.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your
Owner’s Manual.
11
1276473_14a_Q60_Convertible_QRG_062113.indd 11
6/21/13 3:31 PM
f i rst dr i v e f e a t u r e s
USB/iPod® Interface
The USB jack 01 is located in the center console under
the arm rest.
When a compatible USB memory device or iPod®
is plugged into the USB jack, compatible
audio and video files stored on the device
can be played through the vehicle’s audio
system and front display.
01
For more information, refer to the “Monitor, climate, audio, phone
and voice recognition systems (section 4)” of your Owner’s Manual.
Conventional (Fixed Speed) Cruise Control
The cruise control system enables you to set a
constant cruising speed once the vehicle has
reached 25 mph(40 km/h).
04
02
The system will automatically maintain the set speed
until you tap the brake pedal, accelerate, cancel or
turn the system off.
To activate the cruise control, push the ON/OFF
switch 01 . The CRUISE indicator light in the
instrument panel will illuminate.
03
01
To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/
SET switch 02 and release. The CRUISE SET indicator light in the instrument panel will
illuminate. Take your foot off the accelerator pedal. Your vehicle will maintain the set speed.
To reset at a faster cruising speed, push and hold the ACCEL/RES switch 03 . When the
vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the COAST/SET switch 02 . Release the
switch when the vehicle slows to the desired speed.
To cancel the preset speed, tap the brake pedal or push the CANCEL switch 04 .
To turn off cruise control, push the ON/OFF switch 01 . The CRUISE indicator light in the
instrument panel will turn off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
12
1276473_14a_Q60_Convertible_QRG_062113.indd 12
6/21/13 3:31 PM
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
To set Vehicle-To-Vehicle Distance Control mode,
press the ON/OFF button 01 for less than 1.5 seconds.
The CRUISE indicator light 02 will illuminate.
08
07
03
Accelerate to the desired speed.
Push down on the COAST/SET switch 03 and release
it. Cruise control will be set to the desired speed.
Press the distance button 04 repeatedly to change
the set distance between long, middle, and short.
04
When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed indicator
lights will illuminate 05 in set mode.
When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance, and set
vehicle speed indicator lights will illuminate 06 in
set mode.
01
02
05
To reset at a faster cruising speed, push up and hold the ACCEL/RES
switch 07 . When the vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push down and hold the COAST/SET
switch 03 . Release the switch when the vehicle slows to the desired speed.
06
To cancel the preset speed, push the CANCEL switch 08 or tap the brake pedal. The set
vehicle speed indicator 05 will go out.
To turn off cruise control, press the ON/OFF button 01 . The CRUISE indicator light 02 ,
in the instrument panel will turn off.
To set conventional (fixed speed) cruise control mode:
While cruise control is off, press the ON/OFF button 01 and hold it down for more than 1.5
seconds. The CRUISE indicator light will illuminate.
Accelerate to the desired speed.
Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.
Cruise control should be set to the desired speed.
To switch between the two cruise control modes:
When one of the two cruise modes is in use, you must turn the system off, and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
13
1276473_14a_Q60_Convertible_QRG_062113.indd 13
6/21/13 3:31 PM
f i rst dr i v e f e a t u r e s
Opening/Closing the Hard Top (Convertible models)
Before opening or closing the retractable hard top, refer to
your Owner’s Manual for detailed warnings and cautions
regarding hard top operation.
The trunk area must be absolutely empty or it may result
in damage to the hard top.
Preparing to Lower the Hard Top
1.The vehicle must be on a level surface when operating
the hard top.
2.Make sure that the trunk area is absolutely empty.
3.Pull up on the strap to open the trunk room partition.
4.Secure the partition hooks into holders until they latch.
If the trunk room partition hooks are not latched in the
holders, the hard top cannot be operated and
the CHECK SEPARATOR indicator will illuminate
on the vehicle information display located
between the tachometer and speedometer.
5.Securely close the trunk before operating the hard top.
Hard Top Operation
1.Move the shift lever to the P (Park) position
(automatic transmission) or move the shift lever to
the N (Neutral) position (manual transmission) and
apply the parking brake.
2. Start the engine.
3.Press the hard top operating switch, located on the
center console, to OPEN or CLOSE and hold until the
top is fully positioned.
4.The ROOF OPEN or ROOF CLOSED indicator will display when the hard top is fully positioned.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
14
1276473_14a_Q60_Convertible_QRG_062113.indd 14
6/21/13 3:31 PM
s y s t em guide
Trip Computer
W
hen the
button 01 is pressed, the following modes
will appear on the vehicle information display 02 :
• MPG – Displays the current fuel consumption.
01
•
MPG/MPH – Displays the average fuel consumption
and speed since the last reset.
03
•
TIME/MILES – Displays the elapsed time and total
distance the vehicle has been driven since the
last reset.
•
RANGE – Displays the estimated distance to empty
(dte) the vehicle can be driven before refueling.
02
•
OUTSIDE TEMP – Displays the exterior air temperature
including a low temperature warning feature.
•
SETTING – Allows you to set reminders for alerts
and maintenance intervals or change the language and units used in the system.
— Press the
button 03 to cycle through the various setting modes.
— Press the
button 01 to choose the selected mode.
• WARNING – This is availabe when a warning is present.
Press the
button 03 for approximately 1 second to reset the currently displayed
trip odometer to zero.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
Bluetooth® Hands-free Phone System
A
cellular telephone should not be used
while driving so full attention may be given to
vehicle operation.*
Bluetooth® Controls
SYSTEM OPERATING TIPS
T he “Help” command can be used to hear a list of
available commands at any time.
Reduce background noise as much as possible by
closing windows and pointing HVAC vents away
from the ceiling.
Say commands after the tone, or press the
button or the
to say a command at any time.
Speak naturally without long pauses and without
raising your voice.
Microphone
*Some jurisdictions prohibit the use of cellular telephones while driving.
1276473_14a_Q60_Convertible_QRG_062113.indd 15
15
6/21/13 3:32 PM
syste m g ui d e
When speaking Phonebook names, please be aware some phones require the last name
to be spoken before the first name. For example, “Michael Smith” may be spoken as
“Smith Michael”.
T o cancel a voice recognition session, simply wait 5 seconds, say “Cancel” or “Quit”, or
press and hold the button for 5 seconds.
To increase or decrease the volume of the voice prompts, push the volume control switches
or on the steering wheel or turn the VOL/ON•OFF control knob on the audio system
while the system is responding.
I f the Voice Recognition system does not recognize your voice commands, train the system
using the Speaker Adaptation Mode. See your Owner’s Manual for detailed information.
For more detailed information and instructions, refer to your cellular phone Owner’s Manual
and visit www.InfinitiUSA.com/Bluetooth.
Bluetooth® System with Navigation (if so equipped)
CONNECTING PROCEDURE
The vehicle must be stationary when connecting
the phone.
1.Press the phone button on the instrument panel or
the button on the steering wheel and select the
“Connect Phone” key.
2. I nitiate connecting from the phone.
• T he connecting procedure varies according to each
cellular phone model. For detailed connecting
instructions and a list of compatible phones,
please visit www.InfinitiUSA.com/bluetooth.
• W
hen prompted for a PIN code, enter “1234”
from the handset. (The PIN code is assigned
by INFINITI and cannot be changed).
3.When the connecting is complete, the screen will
return to the Phone menu display.
16
1276473_14a_Q60_Convertible_QRG_062113.indd 16
6/21/13 3:32 PM
PHONEBOOK SETUP
D
epending on your cell phone, the system may automatically download your cell phone’s
entire phonebook to the vehicle’s Bluetooth system.
I f the phonebook does not download automatically, the vehicle phonebook may be set for up
to 40 entries.
To manually download entries:
1.Press the
button and select the “Quick Dial” key.
2.S
elect the “Add New” key at the top of the display.
There are different methods to input a phone
number. Select one of the following options:
•
“Copy from Call History” to save a number from
the Outgoing, Incoming or Missed Calls lists.
•“Copy from the Phonebook” to save a number
that has been downloaded from your handset to
the vehicle.
•“Enter Number by Keypad” to input the number
and name manually.
MAKING A CALL
To make a call, follow this procedure:
1.Press the button on the steering wheel. The “Phone”
menu will appear on the control panel display.
2.Select the “Quick Dial”, “Call History”, “Phonebook”
or “Dial Number” key.
3. Select the desired entry from the list.
4. Select “Call” to start dialing the number.
RECEIVING/ENDING A CALL
T o accept the call, press the button on the steering
wheel or touch the “Answer” key. To reject the call,
touch the “Reject Call” key.
T o hang-up, press the
“Hang Up” key.
button or touch the
17
1276473_14a_Q60_Convertible_QRG_062113.indd 17
6/21/13 3:32 PM
syste m g ui d e
Bluetooth® System without Navigation (if so equipped)
PAIRING PROCEDURE
1.Press the
button on the steering wheel. The
system announces the available commands.
2.Say “Connect Phone”. The system acknowledges
the command and announces the next set of
available commands.
3.Say “Add Phone”. The system acknowledges the
command and asks you to initiate connecting from
the phone handset.
4.Initiate pairing from the phone.
•The connecting procedure varies according to each cellular phone model. For detailed
connecting instructions and a list of compatible phones, please visit
www.InfinitiUSA.com/bluetooth.
•When prompted for a PIN code, enter “1234” from the handset. (The PIN code is
assigned by INFINITI and cannot be changed.)
5.Say the name of the phone when the system asks you to provide one. You can give the
phone a name of your choice.
PHONEBOOK REGISTRATION
W
hen the cellular phone is connected to the in-vehicle module, the data stored in the
cellular phone such as phonebook, outgoing call logs, incoming call logs and missed call
logs is automatically transferred and registered to the system.
T he availability of this function depends on each cellular phone. The copying procedure
also varies according to each cellular phone. See your cellular phone Owner’s Manual for
more information.
Up to 1,000 phone numbers per registered cellular phone can be stored in the phonebook.
MAKING A CALL
1. Press the
button on the steering wheel. A tone will sound.
2.Say “Call”. The system acknowledges the command and announces the next set of
available commands.
3.Say the registered person’s name. The system acknowledges the command and
announces the next set of available commands.
4.Say “Yes”. The system acknowledges the command and makes the call.
RECEIVING/ENDING A CALL
T o accept the call, press the
button.
To hang-up, press the
button on the steering wheel. To reject the call, press the
button.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your Owner’s
Manual or please visit www.InfinitiUSA.com/bluetooth.
18
1276473_14a_Q60_Convertible_QRG_062113.indd 18
6/21/13 3:32 PM
01
02
04
09
03
06
05
07
10
08
11
12
13
Navigation System (if so equipped)
Your Navigation System can calculate a route from the current location to a preferred
destination. The real-time map display and turn-by-turn voice guidance will lead you along
the route.
The Navigation System will continually update your vehicle’s position. If you have deviated
from the original route, it will recalculate the route from your current location.
01 Touch screen display.
02 STATUS – Press multiple times to display audio information, the air conditioner status, fuel
economy or navigation directions.
03 Destination (DEST) – Press to enter a destination.
04 ZOOM OUT – Press to view a wider area.
05 ROUTE – Press to access guidance control functions such as guidance cancellation, route
priority or waypoint setting on the route.
06 Infiniti Controller
• ENTER – Press the ENTER button to select the highlighted item on the screen.
•Center Dial – Turn the dial to highlight an item on the screen, adjust a setting or adjust the
map scale.
•Slide the controller (push upward/downward/leftward/rightward) to select an item on the
screen, to adjust a setting or scroll the map in 8 directions.
07 Information (INFO) – Press to display the vehicle, traffic (if so equipped), weather (if so
equipped) or voice recognition information.
1276473_14a_Q60_Convertible_QRG_062113.indd 19
19
6/21/13 3:32 PM
syste m g ui d e
08 – Press to switch between the day screen (bright) and the night screen (dark). Press an
hold the button to turn the display off. Press again to turn the display on.
09 ZOOM IN – Press to view the map in detail.
10 MAP – Press to display the map. While following a programmed route, press multiple times
to change the type of route information.
11 SETTING – Press to access the system settings.
12 BACK – Press to return to the previous screen. In a settings screen, this button can also
be used to apply the setting. In a character input screen, this button can also delete the
characters that have been entered.
13 VOICE – Press to hear the current voice guidance for a programmed route.
For more information, please refer to your Navigation System Owner’s Manual.
DVD Player (if so equipped)
With this DVD player, you can play video files via a
DVD or CD from the front display.
To view movies on the front display, stop the vehicle
in a safe location, move the shift lever to the P
(PARK) position and apply the parking brake.
To reduce driver distraction, movies will not be
shown on the front display while the vehicle is in
any drive position.
For more information, refer to the “Monitor, climate, audio, phone and voice
recognition systems (section 4)” of your Owner’s Manual.
20
1276473_14a_Q60_Convertible_QRG_062113.indd 20
6/21/13 3:32 PM
Homelink®
HomeLink® Universal Transceiver
The HomeLink® system can learn and consolidate the functions of up to 3 different
hand-held transmitters, operating items such as garage doors, property gates, outdoor and
indoor lights or alarm systems.
To program the Homelink® Universal Transceiver:
•Position the handheld transceiver 1-3 in (26-76 mm) away from the Homelink® surface,
keeping the Homelink® indicator light in view.
•Press and hold the desired Homelink® button and the handheld transmitter button
simultaneously until the Homelink® indicator light flashes slowly and then rapidly.
•Both buttons may be released when the indicator light flashes rapidly.
To verify the programing is complete, press and hold the Homelink® and observe the
indicator light:
•A solid continuous light indicates the programing is complete and the Homelink®
button will activate your device.
•A blinking light that turns to a solid continuous light after 2 seconds indicates
additional steps are required to complete the programing.
An additional person may make the remaining steps easier. To complete the
programing process:
•At the receiver of the device that you are programing to the Homelink®, press and
release the “learn” or “smart” button (the name may vary by manufacturer but it is
usually located near where the hanging antenna wire is attached to the unit). You have
approximately 30 seconds to initiate the following step.
•Press and hold the programmed Homelink® button for 2 seconds and release.
Repeat the previous 2 steps up to 3 times to complete the programming process.
Homelink® should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink® website at
www.homelink.com or call 1-800-355-3515.
21
1276473_14a_Q60_Convertible_QRG_062113.indd 21
6/21/13 3:32 PM
Printing: July 2013 (07) / QR14E GV36U0 / Printed in USA
To view detailed instructional videos,
go to www.infinitiownersinfo.mobi/2014/q60
or snap this barcode with an appropriate
barcode reader.
This Quick Reference Guide is intended to provide an overview of some of the unique features
of your new vehicle. See your Owner’s Manual, which contains important safety warnings and
information about the operation and maintenance of your vehicle, for complete details. Nissan
North America, Inc. reserves the right to make changes, at any time, without prior notice, in prices,
colors, materials, equipment, specifications, and models and to discontinue models or equipment.
Due to continuous product development and other pre- and post-production factors, actual vehicle,
materials and specifications may vary. Some vehicles are shown with optional equipment. See
the actual vehicle for complete accuracy. Specifications, options and accessories may differ in
Hawaii, U.S. territories and other countries. For additional information on availability, options or
accessories, see your INFINITI retailer or contact Nissan North America, Inc.
1276473_14a_Q60_Convertible_QRG_062113.indd 1
6/21/13 3:30 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement