Controlling other equipment Chapter 10 Using the remote control with other

Controlling other equipment  Chapter 10 Using the remote control with other
10
Controlling other equipment
Chapter 10
Controlling other equipment
Using the remote control with other
components
The supplied remote control can operate not only this
receiver, but also your TV, DVD player and other
components, once you’ve programmed it with the
appropriate preset code.
RECEIVER
The default preset codes are shown in the table.
1
SLEEP
DVD
STB
DVR/TV
VIDEO
FRONT
FM/AM
AV DIRECT
When you select an input (DVD, STB, DVR/TV, VIDEO,
FRONT or FM/AM), you change both the receiver’s input
source and the remote control mode (see also Remote
Direct function on page 43). Some buttons on the remote
have different functions depending on the current mode
of the remote.
The TV CONTROL buttons are dedicated to controlling
the TV. They will always control the TV no matter what
operation mode the remote is in.
SOURCE
RECEIVER
INPUT
LEVEL
TEST TONE
AUTO
Preset
code
Component
(manufacturer)
DVD
020
DVD (Pioneer)
STB
200
STB (Pioneer)
DVR/TV
466
DVD recorder
(Pioneer)
VIDEO
600
TV (Pioneer)
FRONT
100
LD (Pioneer)
FM/AM
n/a
(built-in tuner)
TV CONTROL
600
TV (Pioneer)
CH SELECT
STEREO
SURROUND
ADVANCED
SURROUND
SOUND
MODE
DIALOG
SIGNAL
SELECT
3
MUTE
MASTER
VOLUME
SYSTEM
SETUP
MCACC
SETUP
TUNE
DTV MENU
TOP MENU
T.EDIT
MENU
ST
ST
ENTER
GUIDE
SEARCH
SUBTITLE
AUDIO
TUNE
DIMMER
SBch MODE
EON RETURN
Input/control mode
select button
2
B
DISPLAY
C
BAND
CLASS
D
A
MPX
E
RF ATT
D.ACCESS
4
DISC
ENTER
10
TV CONTROL
CHANNEL
INPUT
CHANNEL
VOLUME
5
RECEIVER
1 SOURCE
According to the current remote mode, switches an
external component on or into standby.
2 Input/control mode select buttons
Changes the receiver input and also the mode of the
remote control.
3 Receiver control buttons
Buttons used only for controlling receiver functions.
4 Buttons for controlling other components
The function of a particular button varies according to the
remote control mode and the type of component being
controlled. (Some buttons also control receiver
functions.)
5 TV CONTROL buttons
Dedicated buttons for controlling your TV.
42
En
Controlling other equipment
10
Recalling preset codes
• See Preset code list on page 47 for the components
and manufacturers available.
• The preset codes cover a wide variety of equipment,
however, there may be some models from a
particular manufacturer that do not work with any of
the available codes.
SOURCE
RECEIVER
RECEIVER
SLEEP
DVD
STB
DVR/TV
VIDEO
FRONT
FM/AM
AV DIRECT
INPUT
LEVEL
TEST TONE
AUTO
CH SELECT
• With some components, not all functions are
controllable by this remote.
SURROUND
STEREO
SOUND
MODE
SIGNAL
SELECT
MUTE
MASTER
VOLUME
• Refer to VCR / DVD / LD player and DVD recorder
controls on page 45 and Cable TV / satellite TV / digital
TV / TV controls on page 46 for detailed information on
the function of individual buttons.
SYSTEM
SETUP
ROOM
SETUP
TUNE
DTV MENU
TOP MENU
T.EDIT
MENU
ST
ST
ENTER
GUIDE
SEARCH
SUBTITLE
AUDIO
TUNE
VIRTUAL SB
EON RETURN
B
DISPLAY
C
DIMMER
BAND
CLASS
D
A
MPX
E
English
Note
The following steps show you how to recall preset codes
for each input and for the TV CONTROL buttons.
RF ATT
D.ACCESS
DISC
ENTER
10
Remote Direct function
• Default setting: All inputs – ON
TV CONTROL
CHANNEL
INPUT
CHANNEL
VOLUME
RECEIVER
1 Press RECEIVER and number button ‘1’ at the
same time.
The LED starts blinking.
• To cancel the preset mode at any time press
RECEIVER.
• The remote control will also return to the previous
mode after one minute of inactivity.
2 Press the input select button you want to preset.
Select DVD, DVR/TV, FRONT, STB, or VIDEO.
• To preset the TV CONTROL buttons, press TV
CONTROL .
The LED stops blinking and remains lit.
3 Use the number buttons to enter a 3 digit setup
code.
See Preset code list on page 47 for a list of all the codes of
different types of equipment.
On the default setting, when you press an input select
button (DVD, DVR/TV, etc.), both the receiver input
source and the remote control change to the selected
function.
When an input select button is set to OFF, pressing that
button changes the function of the remote control only.
This can be useful when you want to operate one
component without interrupting playback of another.
When set to OFF, use the INPUT button to change the
input source of the receiver.
1 Press RECEIVER and number button ‘4’ at the
same time.
2 Press the input select button you want to set the
remote direct mode for.
Select DVD, DVR/TV, FRONT, STB, or VIDEO. (You can’t
select FM/AM).
3 Press ‘1’ to set the remote direct mode to ON or
‘2’ to set to OFF.
4
Press RECEIVER to finish.
The LED starts blinking again.
After entering a code, a power on/off command is
transmitted by the remote. If the component you want to
control can be switched on/off by remote, it should now
switch on/off.
If the other component fails to switch on/off, try another
preset code if there is one available.
4 Repeat process to assign preset codes for as
many components as you want.
43
En
10
Controlling other equipment
Multi Operation
If you have a number of Pioneer components in your
system, you can take advantage of the Multi Operation
feature of this receiver’s remote control. This switches on
the source component, this receiver, your TV and sets the
receiver’s input function to the correct source.
Before Multi Operation will work correctly, you must
setup the remote to work with your TV and other
components using the correct preset codes (see
Recalling preset codes on page 43).
SOURCE
RECEIVER
SLEEP
DVD
STB
VIDEO
FRONT
LEVEL
TEST TONE
AUTO
STEREO
SURROUND
DVR/TV
FM/AM
CH SELECT
ADVANCED
SURROUND
• Press and hold RECEIVER then press an input
select button (DVD, DVR/TV, STB, VIDEO, FRONT or
FM/AM).
• Note that pressing the FM/AM button does not
cause the TV to switch on.
System Off function
The System Off function allows you to switch off all the
Pioneer components in your AV system at the same time.
• Press RECEIVER and RECEIVER at the same
time.
The receiver and all Pioneer AV components within the
range of the remote control should switch into standby.
Note
• There are a few Pioneer components that do not
respond to the Multi Operation and/or System Off
commands.
Resetting all remote control settings
This restores all presets to the factory defaults. See Using
the remote control with other components on page 42 for
the default remote settings.
• Press RECEIVER and number button ‘0’ (zero) at
the same time. Keep them pressed for about 3
seconds.
The LED on the remote control blinks three times
indicating all the preset codes and the Remote Direct
setting have been reset to the factory defaults.
44
En
Controlling other equipment
10
VCR / DVD / LD player and DVD recorder controls
Button(s)
Function
Components
SOURCE
Press to switch the components between standby and on.
VCR/DVD/LD/DVD-recorder
Press to return to the start of the current track or chapter.
VCR/DVD/LD/DVD-recorder
Press to advance to the next track or chapter. Repeated presses skips VCR/DVD/LD/DVD-recorder
to the start of the following tracks or chapters.
Pause playback or recording
VCR/DVD/LD/DVD-recorder
Hold down for fast-forward playback
VCR/DVD/LD/DVD-recorder
Hold down for fast-reverse playback
VCR/DVD/LD/DVD-recorder
Start playback
VCR/DVD/LD/DVD-recorder
Stop playback (on some models, pressing this when the disc is already VCR/DVD/LD/DVD-recorder
stopped will cause the disc tray to open)
DISC (ENTER)
Use as ENTER
VCR/DVD/LD/DVD-recorder
Press to change the search mode
DVD
Press to display the setup screen (or disc navigator)
DVD-recorder
Press to switch sides of a disc
LD
Use as +10 button when entering numbers
VCR/DVD/LD/DVD-recorder
Press to clear a numeric entry
DVD/DVD-recorder
+10
Number buttons
VCR/DVD/LD/DVD-recorder
Use to directly access tracks, etc. on a program source
Method 1: For numbers 1–9, use the number buttons. For numbers 10
and over, use the +10 button, e.g., +10, +10, 3 for 23.
Method 2: Use the number buttons followed by ENTER, e.g., 2, 3,
ENTER for 23.
Start recording. To prevent accidental recording, these buttons must VCR/DVD-recorder
be pressed together.
MENU
Display menus concerning the current DVD or DVR you’re using
DVD/DVD-recorder
DTV MENU/TOP
MENU
Display the top menu of the current DVD or DVR you’re using
DVD/LD/DVD-recorder
RETURN
Use to go back to the previous menu page
DVD/DVD-recorder
AUDIO
Change the audio track of discs with more than one audio track
DVD/LD/DVD-recorder
SUBTITLE
Display/change the subtitle language on multilingual DVDs
DVD/DVD-recorder
& ENTER
Navigate DVD menus/options
DVD/DVD-recorder
CHANNEL +/–
Use to select channels
VCR/DVD-recorder
ENTER + Press to start recording
DVD-recorder with HDD
ENTER + Press to stop recording
DVD-recorder with HDD
ENTER + Press to switch from DVD/CD to HDD playback mode
DVD-recorder with HDD
ENTER + Press to switch from HDD to DVD/CD playback mode
DVD-recorder with HDD
English
This remote control can control these components after
entering the proper codes (see Using the remote control
with other components on page 42).
45
En
Controlling other equipment
10
Cable TV / satellite TV / digital TV / TV controls
This remote can control these components after entering
the proper codes or teaching the receiver the commands
(see Using the remote control with other components on
page 42).
Button(s)
Function
Components
TV Press to switch between standby and on.
Cable TV/Satellite TV/DTV/TV
INPUT SELECT
Press to switch the TV input
TV
CHANNEL +/–
Use to select channels
Cable TV/Satellite TV/DTV/TV
VOLUME +/–
Use to adjust the TV volume
TV
MENU
Press to display menu screen
Cable TV/Satellite TV/TV
DTV MENU/TOP
MENU
Press to display DTV menu
DTV
RETURN
Use to go back to the previous menu page
Cable TV/Satellite TV/TV/DTV
GUIDE
Use as GUIDE button for navigation
DTV
AUDIO
Use to switch DTV audio channels
DTV
A / Press to select closed captioning
Satellite TV/DTV
Press for information on current program
DTV
Use to move back a page in the menu
Cable TV
B / RED
Satellite TV/DTV
Use to move forward a page in the menu
Cable TV
E / BLUE
Satellite TV/DTV
C / GREEN
Satellite TV/DTV
D / YELLOW
Satellite TV/DTV
+10
Use as +10 button when entering numbers
Cable TV/Satellite TV/TV/DTV
Press to clear a numeric entry
Cable TV/Satellite TV/TV/DTV
DISC (ENTER)
Use as ENTER
Cable TV/Satellite TV/TV/DTV
Number buttons
Cable TV/Satellite TV/TV
Use to directly access TV channels
Method 1: For numbers 1–9, use the number buttons. For numbers 10
and over, use the +10 button, e.g., +10, +10, 3 for 23.
Method 2: Use the number buttons followed by ENTER, e.g., 2, 3,
ENTER for 23.
& ENTER
Press to select or adjust and navigate items on the menu screen
Note
• Depending on the maker and individual model, there
are some buttons that may not be able operate some
equipment or may operate it in a different way.
46
En
Cable TV/Satellite TV/TV
Controlling other equipment
10
DVD player
TV
VCR
Manufacturer
Code
Manufacturer
Code
Manufacturer
Code
PIONEER
000, 003, 008, 020,
111
007
003, 010
014
012
004
013
003
013
009, 011
005
006
002
016 (video game)
015
001
014
PIONEER
ALBA
BUSH
FISHER
FUJITSU
FUNAI
GOLDSTAR
GRANDIENTE
GRUNDIG
HITACHI
ITT
JVC
MITSUBISHI
NOKIA
PANASONIC
PHILIPS
RCA
SALORA
SAMSUNG
SANYO
SHARP
SONY
TANDY
TELEFUNKEN
THOMSON
TOSHIBA
600, 651, 231
639
647
635, 638
648
640
650
657
631, 653
606, 633, 634, 654
642
613
609
632, 652
608, 622
607, 656
618
643
644, 646
645
602
604
641
637
636
605
PIONEER
AIWA
AKAI
ALBA
BAIRD
BUSH
GOLDSTAR
GRADIENTE
GRUNDIG
HITACHI
JVC
MAGNAVOX
MATSU
MITSUBISHI
PANASONIC
SANYO
SHARP
SONY
400, 443
446
442
447, 452
450
448
650
441
453, 454, 455
406
407, 428
414
445
609
408, 432
444
402
416, 417, 457, 458,
459 (digital video)
451
449
405
AKAI
DENON
GOLDSTAR
HITACHI
JVC
LOEWE
PANASONIC
PHILIPS
RCA
SAMSUNG
SHARP
SONY
SONY
THOMSON
TOSHIBA
ZENITH
DVD recorder
Manufacturer
Code
PIONEER
PANASONIC
TOSHIBA
456, 466, 467, 468
465
464
LD player
STB (satellite/CATV)
Manufacturer
Code
PIONEER
DENON
HITACHI
MITSUBISHI
PHILIPS
RADIOLA
SONY
TELEFUNKEN
100, 111(DVD/LD)
110
109
100
104
104
101, 102
100
Manufacturer
Code
PIONEER
JERROLD
SA
ZENITH
200, 204, 231, 700
716
706, 708
717
TELEFUNKEN
THOMSON
TOSHIBA
English
Preset code list
Note
• There are cases where only
certain functions may be
controllable after assigning the
proper preset code, or the codes
for the manufacturer in the list
will not work with the particular
model you are using.
• See page 42 for the default
preset codes.
Digital STB
Manufacturer
Code
PIONEER
200, 204
47
En
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement