I.D. AL - FLASH MPX SD - interactive video player - User manual
Flash MPX SD
MANUAL
® Waves System
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
Table of contents
A - Safety instructions
B - Product information
1 - Product presentation
2 - Installation
3 - Operating mode
4 - First use
5 - Input modes
6 - RS485 serial link protocol
Annexe A - Specifications, functions, type of memory storage
Annexe B : Infrared remote control
1
3
4
5
6
7
9
12
13
14
ID-AL products are exclusively manufactured by Waves System
LA VILLE EN BOIS - 44830 BOUAYE - FRANCE
Sales and information: +33 2 40 78 22 44
E-mail : [email protected] - Web site: http://www.id-al.com
Technical department : [email protected]
Technical support :
For a detailed list of the technical support options, we suggest you to visit our site
www.id-al.com.
Information in this manual is subject to change without notice and do not represent any commitment from
Waves System. The equipment described in this manual is supplied under condition of the terms of
license specifying the legal use conditions. This manual can’t be reproduced or used, in whole or in part,
in any form and by any mean, for other use than private, without the written permission from Waves
System.
ID-AL is a trademarks of Waves System.
® Waves System
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
CAUTION! DO NOT EXPOSE TO HUMIDITY & DUST!
Unplug the power supply cable before any servicing
FOR YOUR SAFETY, PLEASE READ THE USER’S GUIDE CAREFULLY BEFORE OPERATING
YOUR PLAYER.
A. SAFETY INSTRUCTIONS
A.1 CE marking
The CE marking is found on the nameplate, at the rear side of the device. It certifies the conformance
of the device with the low voltage CE Directive, according to the EN 55022 standard, and the
Electromagnetic Compatibility Directive 61000-4-x.
A.2 Directives
• The requirements related to the electromagnetic compatibility and low voltages directive are met.
A.3 Overview
• The user manual is an integral part of the product. It must always be kept handy & close by. Proper
usage conforming to the product intended purpose involves strict compliance with the instructions
given in this manual.
In the event of return of the equipment, the user manual should be handed over to the new purchaser.
The staff should receive instructions concerning the proper usage of the device.
• Only usage of genuine parts ensures perfect safety for the user and correct operation of the
device. Moreover, only accessories mentioned in the technical documentation or explicitly approved
by the manufacturer must be used. In the event of usage of accessories or consumable products
from other brands, the manufacturer cannot stand guarantee for the correct and safe operation of
the device.
• Damages caused through usage of accessories or consumable products from other brands will not
entail right to any benefit under the terms of warranty.
• The manufacturer will be liable for the safety, reliability and functioning of the product as long as the
assembly, settings, modifications, extensions and repairs have been carried out by the manufacturer
or a company approved by the manufacturer and if the device is used in accordance with the instructions mentioned in this manual.
• The player complies with the technical safety standards in force at the date of print of this manual.
All rights reserved for the electrical diagrams, procedures, names and devices mentioned herein.
• Any reproduction of the technical documentation, even partially, without the written authorization
from Waves System is prohibited.
A.4 General Safety instructions
This device has been shipped out from our facilities in perfect working condition. In order to preserve
these conditions, for safety and to avoid any risk of accidental bodily injury, the user must
imperatively follow the safety instructions and read the ‘Caution!’ messages included in this manual.
This device, made by Waves System, has been designed in a way that practically eliminates any risk if
it is used in accordance to its intended purpose. Nevertheless, with a concern for safety, we would like
to draw your attention to the following instructions:
• When using the device, comply with all local rules and regulations in force. Any modification or
® Waves System
-1-
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
conversion of the device automatically entails loss of the homologation. The operation of a modified
device is liable to a penalty. In the interest of occupational safety, the operator and the user are held
responsible for complying with the regulations.
• Keep the original packing for a possible product re-shipment. Also ensure to keep the packing material
out of children's reach. Only this original packing ensures optimal protection for the product during
transportation. If a product reshipment appears to be necessary during the guarantee period, Waves
System is not liable for any ensuing damages arising during the transportation and attributable to a
defective packing.
• This device is used to broadcast audio files. It should be used only by persons whose training or
knowledge ensures proper handling.
• Before every use, the operator must check that the device is in perfect working condition.
• This product must not be used in places where there is a potential explosion risk. Besides, it must
neither be used in an environment favouring combustion nor in a humid or excessively hot or cold
location.
A.5 Safety instructions against risks due to electric currents
• The device must be connected to a grounded AC power outlet or a European standard outlet installed
as per good professional practices.
• Before connecting the device, check that the power supply voltage and frequency match the
specifications indicated on the device.
• Before powering, check that the device and cables are not damaged. Damaged cables and connections
must immediately be replaced.
• Never allow the power cords to come in contact with other cables. Handle the power supply cable as
well as all other cables connected to the mains with extreme care.
• Always connect the plug-in connector in the end. Ensure that the On/Off switch is in 'Off' position
before connecting the device to the mains. The mains outlet must remain accessible after the installation.
• Check the device and its power supply cable from time to time. Disconnect the device from the mains
when it is no longer used or for the purpose of maintenance.
• Handle the power cord by using the plug-in connector only. Never remove the plug-in connector by
pulling the power cord.
• Electrical connection, repairs and maintenance must be carried out by qualified personnel.
• Do not switch on or switch off the device within a short span of time as this will reduce equipment life.
® Waves System
-2-
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
A.6 - Terms of use:
• This product has been designed for indoors use only.
• If this device has been exposed to very high temperature fluctuations (e.g.: after transportation), do not
connect it immediately. The condensation formed inside the device could damage it. Allow the device to
attain ambient temperature before connecting it.
• Do not shake the device, avoid sudden movements during its installation or handling.
• When selecting the spot for installation of the player, ensure that it is not exposed to a high source of
heat, humidity or dust. There should not be any cables lying around as they might jeopardise your &
others safety.
B. PRODUCT INFORMATION
B.1 Correct usage
The player is used to broadcast audio/video files automatically.
Correct usage involves compliance with the instructions given in this manual as well as with the
requirements concerning installation.
B.2 Incorrect usage
Any other usage or usage beyond the scope of this application is considered as incorrect usage. The
manufacturer shall not be liable for the damages ensuing from it. The user shall bear full responsibility for
the risks incurred.
B.3 Delivery details
Flash MPX SD player
External power supply
Remote control
User's manual
B.4 Specifications
Audio/video Player model : Flash MPX SD
Nominal electrical values of the power supply connection
Voltage (V) 100 to 240
Frequency (Hz) 50-60
For details see Annex A
B.5 Installation
The device must be installed in a dust free area.
Do not install the device directly against a wall. To avoid overheating, the ventilation openings
must not be blocked. Take care to leave an empty space above the ventilation slits.
B.6 Electrical connection
Before activation, check whether the mains voltage matches with the voltage indicated on the rating
plate.
® Waves System
-3-
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
1 - Product presentation
The Flash MPX SD is an Audio/Vidéo player. The files are stored on an USB stick, SD card or Compact
Flash. This standalone player can read files automatically when switch on.
Using the trigger input, you can play the selected files.
With the RS485 link, you will send command to the player. (select folder, play, stop ...)
Flash MPX SD is used in digital signage market or integration projects for museums, exhibitions, retail,
theme parks & tourist attractions…
® Waves System
-4-
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
2 - INSTALLATION
7
6
5
4
1 - On/Off switch
2 - Compact Flash connector
3 - SD card connector
4 - USB connector
5 - LEDs
6 - Infrared sensor
7 - Speaker volume output
3
2
1
8 - PSU connector
9 - RS485 serial link
10 - VGA video output
11 - Composite video output
12 - Line audio output
13 - Trigger input
14 - Speaker output
8
9
10
RS485
serial
11
12
13
14
Audio
3 (up to 7)
contacts
Speakers
PSU 12V
Video
Digital input :
- For 3 input, direct link (see picture at left)
- For 7 input, you need to combine the input
with few diodes (see picture at right)
® Waves System
-5-
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
3 - First use
Connect the Flash MPX SD on a video display and insert a media (USB stick, SD card, CF) with few mpeg
video files. Connect the PSU and switch on. You can see your video. If no media is detected, you will see
a jpeg background image.
Compact Flash
SD Card
USB flash memory
Welcome page with no media.
® Waves System
-6-
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
4 - Quick Start
The Flash MPX SD plays from :
- USB falsh memory
- SD card or Compact Flash memory
Don’t use name over 8 characters. No space
NO
my video file.mpg
MY VIDEO FOLDER
-> YES
-> myfile.mpg
-> VIDEO
Please, don’t use Apple MAC to copy the files on the memory. Do not use MAC to create the «playlist.txt»
file. Name «playlist.txt» using lower case letters. Do not use capital letters. This file is required only if you
want to play video using push buttons. The playlist.txt is a file that relates (lists) video files to certain
inputs. The purpose of this playlist is to create “software input” so that each file can be associated
How to play file when switch on (autoplay mode) ?
1 - Copy at least one file at root of the media.
Example :
flower.mpg
sea.mpg
boat.mpg
Note : Flash MPX SD don’t read file inside sub folder.
How to start files from inputs ?
1 - At least one file at root of the media
2 - The «playlist.txt» file with the information about triggers input.
3 - A folder including the files to play
Example of a media :
File : «playlist.txt»
010000=file1.mpg
020000=file2.vob
040000=file3.mp3
Input number
® Waves System
-7-
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
myvideo.mpg
playlist.txt
\TRIG
\file1.mpg
\file2.vob
\file3.mp3
->
->
->
->
->
->
play in loop when switch on
config file
Folder with files to play
Play file1.mpg with input 1)
Play file2.mpg with input 2)
Play file3.mpg with input 3)
Explanation :
- When switch on, Flash MPX SD play «myvideo.mpg» in loop.
- With a contact on input 1, Flash MPX SD play «file1.mpg» and return to the root file «myvideo.mpg»
- With a contact on input 2, Flash MPX SD play «file2.mpg» and return to the root file «myvideo.mpg»
- With a contact on input 3, Flash MPX SD play «file3.mpg» and return to the root file «myvideo.mpg»
® Waves System
-8-
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
5 - Input modes
5.1 - Standard mode
playlist.txt is a text file that contains the Flash MPX SD setup and instruction on how you want the input
(push button) to play the files that are located inside the file folder.
example : 010000=file1.mpg
●
The first 2 numbers are for input
Example : 010000=file1.mpg
You can combine the 3 inputs to create up to 7 inputs (binary).
01 : Contact 1
02 : Contact 2
03 : Contact 3
04 : Contact 4
05 : Contact 5
06 : Contact 6
07 : Contact 7
-> Input 1 + 2
-> Input 1 + 4
-> Input 2 + 4
-> Input 1 + 2+ 4
You can create up to 59 lines from 00xxxxxx to 59xxxxxx and use the jump function.
Example :
030000=flower.mpg
060000=boat.mpg
590000=car.mpg
●
-> Input 3
-> Input 6
-> Jump to line 59
Third number is not used.
Example : 010000=file1.mpg
Reserved for a future use. Must be to 0
●
Fourth number is for interrupt.
Example : 010000=file1.mpg
0 : play the file with interrupt
1 : play the file NO interrupt
●
Fifth and sixth numbers are for “what to do” OR “where to go” after playing a file.
Example : 010000=file1.mpg
010000=fichier1.mpg
010005=fichier1.mpg
010026=fichier1.mpg
® Waves System
-> 00 : Play the files at root
-> Jump to line 05xxxx
-> Jump to line 26xxxx
-9-
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
Example of «playlist.txt» file
010000=file1.mpg
020012=file2.vob
030112=file3.mpg
040026=file4.mpg
120100=filexx.vob
260000=fileyy.mpg
-> Play file «file1.mpg» when input 1 is triggered and return to root
-> Play file «file2.vob» when input 2 is triggered and jump to line 12*
-> Play file «file3.mpg» when input 3 (1+2) is triggered and jump to line 12**
-> Play file «file4.mpg» when input 4 is triggered and jump to line 26*
-> Play file «fichierxx.vob» and return to root**
-> Play file «fichieryy.mpg» and return to root*
* : File can be interrupted
** : File can not be nterrupted
Special codes :
- Code «00»
010000=file1.mpg
After read «file1.mpg», Flash MPX SD return to the root and read the files
- Code «99»
010099=file1.mpg
Flash MPX SD stop and wait a new command. Display a black screen.
- Code «98»
010098=file1.mpg
File «file1.mpg» is read in loop
® Waves System
- 10 -
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
Annexe A - Specifications
• Power supply : 12V DC
• Size :
Width : 160mm - Height : 28mm
Depth without connector : 135mm
• Connectors :
- Audio/Vidéo :
1 x VGA Sub D 15 pins
1 x Video CVBS / composite output - RCA
1 x Audio output - RCA
1 x Speaker output - Screw terminal
- Infrared remote control
- Media :
1 x USB - type A - USB 1.1 and 2.0 compatible
1 x SD card connector
1 x Compact Flash connector
Functions
Video output :
• PAL/576p - 720x576 (4:3 and 16:9) - Composite out
• NTSC/480p - 720x480 (4:3 and 16:9) - Composite out
• VGA 640x480 - VGA out
Format :
• .vob (DVD) .mpg (MPeg 2)
• .jpg (still images)
• .mp3 (up to 320kbps) .wav (16 bits / 44.1 and 48 kHz)
Don’t use video file over 9 Mbit/s.
Storage
• SD card : SD/SDHC
• Compact Flash
• USB memory flash compatible USB 1.1 and USB 2.0
® Waves System
- 13 -
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
Annexe B - Télécommande infrarouge
Le lecteur peut être commandé par une télécommande infrarouge car il intègre un capteur accessible à
l’avant de la carte.
Key
Function
Power
Title
INFO
Mute
1
2
3
4
5
6
7
8
9
0
Repeat
Time seek
TV mode
Home
Menu
Slow
Setup
Zoom
Vol +
Vol Up Arrow
Down Arrow
Left Arrow
Right Arrow
OK
Audio
Subtitle
Resume
Angle
Pause
Return
Stop
Rwd
Fwd
Prev
Next
ON/OFF
file list (2 steps)
Time remaining
Mute
Input 1
Input 2
Input 3
Input 4
Input 5
Input 6
Input 7
Input 8
Input 9
Input 0
Repeat mode
Slow 3/4x, 1/2x, 1/4x, 1/8x, 1/16x
Setup Menu
Volume +
Volume Up
Down
Left
Right
OK / PLAY
Play/Pause
Play image by image
Stop
Rewind
Fast forward
Previous file
Next file
® Waves System
- 14 -
V 1.0 - 2011
I.D. AL - FLASH MPX SD - interactive video player - User manual
http://www
.id-al.com
http://www.id-al.com
® Waves System
V 1.0 - 2011
">
