Delfield F15PC72N Installation manual

Delfield F15PC72N Installation manual
International F5 and F15 Series
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment!
Notify carrier of damage! Inspect all components immediately.
F5 and F15 SERIES
Drop-In and Serview Display Cases
CAUTION
Important Information
Read Before Use
Please Save These Instructions!
September 2013
International F5 & F15 Series Service and Installation Manual
Important Warning And Safety Information
WARNING
Read This Manual Thoroughly Before Operating, Installing, Or Performing Maintenance On The Equipment.
WARNING
Failure To Follow Instructions In This Manual Can Cause Property Damage, Injury Or Death.
WARNING
Do Not Store Or Use Gasoline Or Other Flammable Vapors Or Liquids In The Vicinity Of This Or Any Other
Appliance.
WARNING
Unless All Cover And Access Panels Are In Place And Properly Secured, Do Not Operate This Equipment.
WARNING
This Appliance Is Not Intended For Use By Persons Who Lack Experience Or Knowledge, Unless They Have
Been Given Supervision Or Instruction Concerning Use Of The Appliance By A Person Responsible For Their
Safety.
WARNING
This Appliance Is Not To Be Played With.
Warning
Do Not Clean With Water Jet.
WARNING
Do Not Use Electrical Appliances Inside The Food Storage Compartment Of This Appliance.
CAUTION
Observe the following:
2
•
Minimum clearances must be maintained from all walls and combustible materials.
•
Keep the equipment area free and clear of combustible material.
•
Allow adequate clearance for air openings.
•
Operate equipment only on the type of electricity indicated on the specification plate.
•
Unplug the unit before making any repairs.
•
Retain this manual for future reference.
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
International F5 & F15 Series Service and Installation Manual
Contents
Receiving & Inspecting Equipment....................................................3
Serial Number Location.....................................................................4
Warranty Information.........................................................................4
Regulatory Certifications....................................................................4
Specifications................................................................................ 5-6
Installation..................................................................................... 7-8
Shelf Installation................................................................................9
Display Lock Operation......................................................................9
Operation...........................................................................................9
Temperature Control Settings...........................................................10
Pressure Control Settings................................................................10
Maintenance.............................................................................. 11-12
Condenser Air Flow.........................................................................13
Sliding Door....................................................................................14
Replacement Parts..................................................................... 14-17
Wiring Diagram................................................................................18
Standard Labor Guidelines...............................................................19
Receiving And Inspecting The Equipment
Even though most equipment is shipped crated, care should be
taken during unloading so the equipment is not damaged while
being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
2. If damaged, open and inspect the contents with the
carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally as
well as in written form.
4. Request an inspection by the shipping company of the
damaged equipment. This should be done within 10 days
from receipt of the equipment.
5. Check the lower portion of the unit to be sure legs or
casters are not bent.
6. Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines
are secure and base is still intact.
7. Freight carriers can supply the necessary damage forms
upon request.
8. Retain all crating material until an inspection has been
made or waived.
Uncrating the Equipment
First cut and remove the banding from around the crate.
Remove the front of the crate material, use of some tools will
be required. If the unit is on legs remove the top of the crate
as well and lift the unit off the skid. If the unit is on casters it
can be "rolled" off the skid.
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
3
International F5 & F15 Series Service and Installation Manual
Serial Number Location
The serial number on all self-contained F5 Series units is
located near the condensing unit. On all remote F5 Series
units the serial number is located on the drop-in frame.
The serial number on all self-contained F15 Series units is
located behind the compressor housing. On all remote F15
Series units the serial number is located behind the six inch
panel in the base.
Always have the serial number of your unit available when calling
for parts or service. A complete list of authorized Delfield parts
depots is available at www.delfield.com.
©2013 The Delfield Company. All rights reserved. Reproduction without
written permission is prohibited.
SERIAL #
MODEL #
INSTALLATION DATE:
Warranty Information
Visit http://www.delfield.com/minisite/service/warranty_info to:
• Register your product for warranty.
• Verify warranty information.
• View and download a copy of your warranty.
Regulatory Certifications
Models are certified by:
National Sanitation Foundation (NSF)
Technical Inspection Association
European Conformity
4
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
International F5 & F15 Series Service and Installation Manual
Export F5 Series Specifications
24” (61cm) Deep Self-Contained Drop-In Refrigerated Display Cases
Storage
capacity FT3/L
Volts/Hertz/
Phase
F5MC48N-E
18.07/512
F5SC48N-E
System
Cabinet Load Capacity BTU/
BTU/Hour
Hour
Amps
Max. Lamp
Watts
230-240/
50/1
6.0
25
1215
18.97/537
230-240/
50/1
6.0
25
F5PC48N-E
18.97/537
230-240/
50/1
6.0
F5MC72N-E
28.05/794
230-240/
50/1
F5SC72N-E
28.05/794
F5PC72N-E
29.47/834
Model
H.P.
R404A Charge,
OZ.
Temp Class
2970
1/2
32
N
1867
2970
1/2
32
N
25
1945
2970
1/2
32
N
6.0
40
1783
5821
3/4
48
N
230-240/
50/1
6.0
40
2791
5821
3/4
48
N
230-240/
50/1
6.0
40
2884
5821
3/4
48
N
H.P.
R404A Charge,
OZ.
Temp Class
30” (76.2cm) Deep Self-Contained Drop-In Refrigerated Display Cases
Storage
capacity FT3/L
Volts/Hertz/
Phase
F5MC48D-E
23.88/676
F5SC48D-E
System
Cabinet Load Capacity BTU/
BTU/Hour
Hour
Amps
Max. Lamp
Watts
230-240/
50/1
6.0
25
1282
2970
1/2
32
N
24.78/787
230-240/
50/1
6.0
25
1934
2970
1/2
32
N
F5PC48D-E
24.78/787
230-240/
50/1
6.0
25
2012
2970
1/2
32
N
F5MC72D-E
37.07/1050
230-240/
50/1
6.0
40
1870
5821
3/4
48
N
F5SC72D-E
37.07/1050
230-240/
50/1
6.0
40
2878
5821
3/4
48
N
F5PC72D-E
38.49/1090
230-240/
50/1
6.0
40
2971
5821
3/4
48
N
Model
M = Mirror Back • P = Pass Thru • S = See Thru • C = Self-Contained • N = Narrow • D = Deep 30”
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
5
International F5 & F15 Series Service and Installation Manual
Export F15 Series Specifications
24” (61cm) Deep Self-Contained Serview Refrigerated Display Cases
Shelf Capacity
FT2/CM2
Display/Base
Storage
Capacity FT3/L
Display/Base
Volts/Hertz/
Phase
F15MC48N-E
18.78/17447
3.4/3159
18.07/512
9.11/258
230-240/
50/1
6.0
25
1569
F15SC48N-E
21.05/19556
3.4/3159
18.97/537
9.11/2.58
230-240/
50/1
6.0
25
F15PC48N-E
21.05/19556
3.4/3159
18.97/537
9.11/258
230-240/
50/1
6.0
F15MC72N-E
29.28/27202
7.9/7339
28.05/794
18.10/513
230-240/
50/1
F15SC72N-E
32.58/30547
7.9/7339
29.47/834
18.10/513
F15PC72N-E
32.88/30547
7.9/7339
29.47/834
18.10/513
Model
H.P.
R404A
Charge,
OZ.
Temp
Class
8146
3/4
48
N
2221
8146
3/4
48
N
25
2299
8146
3/4
48
N
6.0
40
2361
9422
3/4
48
N
230-240/
50/1
6.0
40
3369
9422
3/4
48
N
230-240/
50/1
6.0
40
3462
9422
3/4
48
N
H.P.
R404A
Charge,
OZ.
Temp
Class
Amps
System
Max. Lamp Cabinet Load Capacity
Watts
BTU/Hour
BTU/Hour
30” (76.2cm) Deep Self-Contained Serview Refrigerated Display Cases
Shelf Capacity
FT2/CM2
Display/Base
Storage
Capacity FT3/L
Display/Base
Volts/Hertz/
Phase
F15MC48D-E
18.78/17447
3.4/3159
23.88/676
9.11/258
230-240/
50/1
6.0
25
1636
8146
3/4
48
N
F15SC48D-E
21.05/19556
3.4/3159
24.78/787
9.11/258
230-240/
50/1
6.0
25
2288
8146
3/4
48
N
F15PC48D-E
21.05/19556
3.4/3159
24.78/787
9.11/258
230-240/
50/1
6.0
25
2366
8146
3/4
48
N
F15MC72D-E
29.28/27202
7.9/7339
37.07/1050
18.10/513
230-240/
50/1
6.0
40
2448
9422
3/4
48
N
F15SC72D-E
32.58/30547
7.9/7339
38.49/1090
18.10/513
230-240/
50/1
6.0
40
3456
9422
3/4
48
N
F15PC72D-E
32.88/30547
7.9/7339
38.49/1090
18.10/513
230-240/
50/1
6.0
40
3549
9422
3/4
48
N
Model
Amps
System
Max. Lamp Cabinet Load Capacity
Watts
BTU/Hour
BTU/Hour
M = Mirror Back • P = Pass Thru • S = See Thru • C = Self-Contained • N = Narrow • D = Deep 30”
6
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
International F5 & F15 Series Service and Installation Manual
Installation: Self-Contained F5 Series
Location
Units represented in this manual are for indoor use only. All
self-contained units were tested at the factory to assure proper
operation. The unit should not be installed directly next to high
heat generating equipment (ranges, griddles, etc.). Be sure the
location chosen has a counter strong enough to support the
total weight of the cabinet and contents. A fully loaded model
may weigh as much as 2,000 pounds! Reinforce the counter as
necessary to provide for maximum loading.
These units are installed by “dropping” them into the counter
from above. The counter cutout sizes are as follows:
48” wide units — 18.62" x 23.62" (47.3 cm x 60.0 cm)
72” wide units — 18.62" x 32.62" (47.3 cm x 82.9 cm)
Self-contained F5 Series units require airflow to the
compressor. Two louvers are provided with each unit and
should be installed as illustrated on page 13.
Unit is designed to maintain 36°F (2°C) to 40°F (4°C) interior
cabinet temperature at 55% or lower ambient relative humidity.
Plumbing
Self-contained models are standard with a condensate
evaporator. If, for some reason, a unit does not have a
condensate evaporator, or the evaporator fails, the unit’s
drain must have an outlet to an appropriate drainage area or
container.
Moisture collecting from improper drainage
can create a slippery surface on the floor
and a hazard to employees. It is the owner’s
CAUTION
responsibility to provide a container or outlet
for drainage.
Electrical connection
Refer to the amperage data on the specification pages, the
serial tag, your local code or the National Electrical Code to
be sure the unit is connected to the proper power source. A
protected circuit of the correct voltage and amperage must be
run for con­nec­tion of the line cord, or permanent connection
to the unit.
Self-contained units have an ON/OFF switch in the junction
box. Simply turn the switch to ON to begin operation.
The power switch should be turned to OFF and
the unit disconnected from the power source
whenever performing service or maintenance
functions.
Installation: Remote F5 Series
1.75"
(4cm)
Cutout
3.00" X 12.00" (8cm X 30cm)
Centered Front To Back
0.25" (0.6cm) From End
3.75"
(10cm)
C
R
J= Junction Box
R= Refrigeration Lines,
0.25" Liquid,
0.37" Suction
D= 0.50" I.D. Drain
D
J
3.75"
(10cm)
Front Of Unit
Typical Mechanical Access (Plan View)
All F5 Models
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
7
International F5 & F15 Series Service and Installation Manual
Installation: Self-Contained F15 Series
Location
Plumbing
Units represented in this manual are for indoor use only. Be
sure the location chosen has a floor strong enough to support
the total weight of the cabinet and contents. A fully loaded model
may weigh as much as 3,000 pounds! Reinforce the floor as
necessary to provide for maximum loading.
For the most efficient refrigeration, be sure to provide good air
circulation inside and out. Don’t pack the refrigerator so full
that air cannot circulate. Be sure that the exterior of the unit has
access to ample air. Avoid hot corners and locations near stoves
and ovens.
Self-contained models are standard with a condensate
evaporator. If your unit does not have a condensate evap­o­ra­tor,
or the evaporator fails, the unit’s drain must have an outlet to an
appropriate drainage area or container.
Moisture collecting from improper drainage can
create a slippery surface on the floor and a hazard
to employees. It is the owner’s responsibility to
CAUTION
provide a container or outlet for drainage.
Unit is designed to maintain 36°F (2°C) to 40°F (4°C) interior
cabinet temperature at 55% or lower ambient relative humidity.
Leveling
A level cabinet looks better and will perform better because
the drain pan will drain properly, the doors will line up with
the frames properly and the cabinet will not be subject to
undue strain. Units come standard with adjustable legs and
bullet feet to make leveling easier. If your unit has casters,
install in a stable condition with the front casters locked before
operating.
Electrical connection
Refer to the amperage data on the specification pages, the serial
tag, your local code or the National Electrical Code to be sure the
unit is connected to the proper power source. A protected circuit
of the correct voltage and amperage must be run for con­nec­tion
of the line cord, or permanent connection to the unit.
Self-contained units have an ON/OFF switch located directly
behind the louvered panel covering the compressor section.
Simply turn the switch to ON to begin operation.
The power switch should be turned to OFF and
the unit disconnected from the power source
whenever performing service or maintenance
functions.
Installation: Remote F15 Series
30.00"
76cm
1.75"
4cm
D
3.75"
10cm
1.00"
2.5cm
C
R
D
J
3.75"
10cm
Front Of Unit
Typical Mechanical Access (Plan View)
All F15 Models
8
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
J= Junction Box
R= Refrigeration Lines,
0.25" Liquid,
0.37" Suction
D= 0.50" I.D. Drain
International F5 & F15 Series Service and Installation Manual
Shelf Installation
Display Lock Operation
Display cases come with four epoxy coated wire shelves that
are adjustable in 3-3/4" increments.
Maximum weight for shelves is 75 pounds.
Overloading shelves can damage equipment or
CAUTION
cause bodily injury.
At the factory, the keys are taped to the display case. Follow the
directions below to lock and unlock the display case.
To lock: Line up key ridge with red dot.
Insert key and rotate one-half turn.
Remove key and push lock bolt in.
To open:Line up ridge with red dot.
Insert key and rotate key one-half turn.
Remove key.
Operation
After turning the ON/OFF switch to ON the unit’s com­pres­sor
will begin operating. Delfield display cases are designed to
maintain an operational temperature of 36°F to 40°F (2°C to
4°C) in both the display (F5 and F15 Series) and storage areas
(F15 Series only).
Located on the operator side at the top right is an ON/OFF
switch for the display lights.
The display temperature control is located in the fan shroud. The
F15 base thermostat is located in the mechanical compartment.
Use the knob to adjust the temperature, adjustments should
be made gradually. Several small adjustments will be more
effective than one large adjustment. It may take an hour or
longer to realize the temperature change depending on the
application and location of the unit.
Continuous opening and closing of the doors will hinder the
unit’s ability to maintain operational tem­per­a­tures.
If humidity is above 55%, condensation on the glass
will be present.
F15 Refrigerated Base Evaporator Fan Operation
When the refrigerator is initially powered up or immediately
following a power outage the unit will begin cooling after a 3-6
minute delay. During normal operation the evaporator fan pulses
independently of the compressor as dictated by the controller
as follows:
1. During the cooling mode, compressor and evaporator fan
run simultaneously.
2. During the compressor off mode, evaporator fan pulses
three minutes on and three minutes off.
3. During an actual defrost event other than the off-cycle
defrost, compressor stays off but the evaporator fan runs
continuously.
Cooling Cycle
Compressor On
Compressor Off
Defrost Cycle
Compressor Off
Evap Fan Evap Fan Evap Fan Evap Fan Evap Fan Evap Fan
On
Off
On
Off
On
Off
X
Cycles On 3-Min,
Off 3-Min
X
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
9
International F5 & F15 Series Service and Installation Manual
Display Temperature Control Settings
The display temperature control is located on the evaporator
assembly on the ceiling of the display case. It is field
adjustable and does not require a service agent. The factory
setting is 2.5. Set toward 1 for higher temperatures and
toward 7 for lower temperatures.
Please make small incremental adjustments if
a temperature adjustment is necessary. It may
take an hour or longer to realize the temperature
change depending on the application and location
of the unit.
Contact the service department at Delfield +1
(989) 773-7981 or your local service agent
for additional assistance. Delfield is not
responsible for charges incurred while adjusting
the thermostat.
Base Temperature Control Settings
The base temperature control is located in the machine
compartment. It is field adjustable and does not require a
service agent. The factory setting is 2.5. Set toward 1 for
higher temperatures and toward 7 for lower temperatures.
Please make small incremental adjustments if
a temperature adjustment is necessary. It may
take an hour or longer to realize the temperature
change depending on the application and location
of the unit.
Contact the service department at Delfield +1
(989) 773-7981 or your local service agent
for additional assistance. Delfield is not
responsible for charges incurred while adjusting
the thermostat.
Pressure Control Settings
Low pressure cut in at 20 psi.
Low pressure cut out at 5 psi.
Differential setting of 15 psi.
10
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
International F5 & F15 Series Service and Installation Manual
Maintenance
Door Gasket Maintenance
Door gaskets require regular cleaning to prevent mold and
mildew build up and also to retain the elasticity of the gasket.
Gasket cleaning can be done with the use of warm soapy water.
Avoid full strength cleaning products on gaskets as this can
cause them to become brittle and crack. Never use sharp tools
or knives to scrape or clean the gasket. Gaskets can be easily
replaced and do not require the use of tools or an authorized
service person. The gaskets are “Dart” style and can be pulled
out of the groove in the door and new gaskets can be “pressed”
back into place.
Drain Maintenance - Base
Each unit has a drain located inside the unit that removes
the condensation from the evaporator coil and routes it to an
external condensate evaporator pan. Each drain can become
loose or disconnected during normal use. If you notice water
accumulation on the inside of the unit be sure the drain tube
is connected to the evaporator drain pan. If water is collecting
underneath the unit make sure the end of the drain tube is in
the condensate evaporator in the machine compartment. The
leveling of the unit is important as the units are designed to
drain properly when level. Be sure all drain lines are free of
obstructions.
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
Cleaning solutions need to be alkaline based or non-chloride
cleaners. Any cleaner containing chlorides will damage
the protective film of the stainless steel. Chlorides are also
commonly found in hard water, salts, and household and
industrial cleaners. If cleaners containing chlorides are used be
sure to rinse repeatedly and dry thoroughly. Routine cleaning
of stainless steel can be done with soap and water. Extreme
stains or grease should be cleaned with a non-abrasive cleaner
and plastic scrub pad. Always rub with the grain of the steel.
There are stainless steel cleaners available which can restore
and preserve the finish of the steels protective layer. Early signs
of stainless steel breakdown are small pits and cracks. If this
has begun, clean thoroughly and start to apply stainless steel
cleaners in attempt to restore the passivity of the steel.
CAUTION
Do not throw items into the display case. Failure
to follow these recommendations could result in
damage to the interior or blower coil. Overloading,
restricting the airflow, and continuous opening and
closing of the doors will hamper the units ability to
maintain operational temperature.
Caster Maintenance
Wipe casters with a damp cloth monthly to prevent corrosion.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service, maintenance functions or
cleaning the refrigerated area.
Refrigerators
The interior and exterior can be cleaned using soap and warm
water. If this isn’t sufficient, try ammonia and water or a
nonabrasive liquid cleaner. When cleaning the exterior, always
rub with the “grain” of the stainless steel to avoid marring the
finish. Do not use an abrasive cleaner because it will scratch the
stainless steel and can damage the breaker strips and gaskets.
Stainless Steel Care and Cleaning
To prevent discoloration or rust on stainless steel several
important steps need to be taken. First, we need to understand
the properties of stainless steel. Stainless steel contains 7080% iron, which will rust. It also contains 12-30% chromium,
which forms an invisible passive film over the steel's surface,
which acts as a shield against corrosion. As long as the
protective layer is intact, the metal is still stainless. If the film
is broken or contaminated, outside elements can begin to
breakdown the steel and begin to form discoloration or rust.
Proper cleaning of stainless steel requires soft cloths or plastic
scouring pads.
Never use an acid based cleaning solution! Many
food products have an acidic content, which can
deteriorate the finish. Be sure to clean the stainless
steel surfaces of ALL food products. Common items
include, tomatoes, peppers and other vegetables.
Cleaning the Condenser Coil
In order to maintain proper refrigeration performance, the
condenser fins must be cleaned of dust, dirt and grease
regularly. It is recommended that this be done at least every
three months. If conditions are such that the condenser is totally
blocked in three months, the frequency of cleaning should be
increased. Clean the condenser with a vacuum cleaner or stiff
brush. If extremely dirty, a commercially available condenser
cleaner may be required.
Failure to maintain a clean condenser coil can initially cause high
temperatures and excessive run times. Continuous operation
with a dirty or clogged condenser coil can result in compressor
failure. Neglecting the condenser coil cleaning procedures will
void any warranties associated with the compressor and cost
to replace the compressor.
CAUTION
Never use a high-pressure water wash for this
cleaning procedure as water can damage the
electrical components located near or at the
condenser coil.
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
11
International F5 & F15 Series Service and Installation Manual
Maintenance, continued
Doors/Hinges
Over time and with heavy use the doors hinges may become
loose. If this happens tighten the screws that mount the hinge
brackets to the frame of the unit. Loose or sagging doors can
cause the hinges to pull out of the frame, which may damage
both the doors and the hinges. In some cases this may require
qualified service agents or maintenance personnel to perform
repairs.
Do not place hot pans on/against the blue ABS liner.
Do not throw items into the storage area. Failure
to follow these recommendations could result in
damage to the interior of the cabinet or to the blower
coil. Overloading the storage area, restricting the
airflow, and continuous opening and closing of the
doors and drawers will hamper the units ability to
maintain operational temperature.
Preventing blower coil corrosion
To help prevent corrosion of the blower coil, store all acidic
items, such as pickles and tomatoes, in sealable containers.
Immediately wipe up all spills.
Cleaning the condensate evaporator (remote models only)
The stainless steel condensate evaporator pan should be
cleaned every six months. Use a vacuum cleaner or damp cloth
to remove dust that may have accumulated. This will prevent
corrosion of the stainless steel.
12
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
International F5 & F15 Series Service and Installation Manual
Condenser Air Flow: F5
F5 units are designed to be operated with two supplied louvered
panels for proper air flow. Failure to provide the proper air flow
will void the warranty. Louver cut-outs are 22" by 11" (55.9cm
by 27.9cm) typical. Cut-outs are to begin a maximum of
4.00" (10.2cm) from the counter-top. Proper installation must
provide for air flow to and from the condensing unit. Install as
shown below.
48" Wide Units Air Flow Detail
Discharge Air
Louver
Cond.
Louver
Fresh Air
72" Wide Units Air Flow Detail
An “air duct” should be constructed from the air-intake louver to the condenser. This is
recommended to prevent recirculation of discharge air.
DisCharge
Air
11.00"
28cm
22.00"
56cm
Cond.
Discharge air louver may be located further from fresh air louver or on the opposite side of
counter.
22.00"
12.00"
56cm
30cm
Louver Minimum
Cutout Distance
Between
Louvers
Fresh
Air
Duct
Top
View
22.00"
56cm
Louver
Cutout
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
13
International F5 & F15 Series Service and Installation Manual
Sliding Door
All Delfield F5 Series and F15 Series display cases feature
a sliding door assembly. A typical sliding door assembly is
shown in the illustration at right.
Maintenance
Frequent, regular cleaning with a mild soap and water solution
will keep the tracks free of foreign matter and will insure many
years of service.
The glass may be cleaned with one of the many commercial
glass cleaners currently available.
If it becomes necessary to replace a sliding door as­sem­bly
or a glass panel, have your unit’s model and serial numbers
available when you call Delfield’s Service and Parts Department
at (800) 733-8829. Indicate that your unit has the sliding door
assembly when you call.
Standard With Door Lock
Sliding Door Removal
Open the door almost completely. Firmly grasp both sides of
the door. Lift the door up and move it until it enters a notch
and can be lifted higher. Tilt the bottom out without removing
the top. Use the top to gently return the spring to the closed
position. Remove the door from the top track.
Sliding Door Reinstall
There is a notch in the top inside corner of the door. Put the
spring in the door's notch and move the spring to the open
position. Put the top into the track and find the notch where the
door can be lifted higher. Set bottom of the door into the track.
See-thru Panel
Replacement Parts
48" Units
72" Units
Part #
Description
Part #
Description
3234636
Bearing, roller, single
3234637
Bearing, roller, double
3234808
Gasket, bumper, 31 13/16"
3234808
Gasket, bumper, 31 13/16"
3234809
Gasket, wiper strip, 30 3/8"
3234809
Gasket, wiper strip, 30 3/8"
3234810
Spring, 17" gold
3233946
Spring, 30" gold
3234803
Track, bottom, 43 7/16"
3234805
Track, bottom, 67 7/16"
3234800
Track top, 44 7/16"
3234802
Track top, 68 7/16"
3455397
See thru panel
3455399
See thru panel
3237549
Replacement lock, units 2007 and after
3237549
Replacement lock, units 2007 and after
3233986
Replacement lock, units prior to 2007
3233986
Replacement lock, units prior to 2007
Note: Pass-thru units have two sets of sliding display doors, see-through and mirror-back units have one set.
14
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
International F5 & F15 Series Service and Installation Manual
Condensing Unit Assembly 1/2 H.P. F5 48" Models
5
Key
1
2
3
4
6
4
1
3
2
7
5
6
7
8
9
8
9
Part Number
000-BN5-003O
3516554
2160019
2162721
Danfoss
#117U5017
Danfoss
#117U6011
3527045
000-998-0032
3516322
039-231-0031
3516455
Description
Assembly, 1/2HP Condenser, Med
Condenser fan blade
Condenser fan guard
Condenser fan motor, 230V
Start Capacitor
Start Relay
Compressor, SC12MLX, 220/50
Hi pressure assembly, 13A, 220
Filter Drier
Pan, Condensate
Condenser coil
Condensing Unit Assembly 3/4 H.P. F15 Models, F5 72" Models
4
2
3
1
Key
Delfield Part #
Description
-
000-BN5-003P
Condensing Unit Assembly, 230-240V
1
026-C58-0032
Shroud, 3/4 HP condenser coil
2
2160019
Guard, fan, condenser, upright
3516433
Blade, fan 25º, 10”, CW, upright
2162721
Motor, fan, 230-240V
3
000-998-0032
Hi Pressure Assembly
4
3527010
Compressor, 3/4HP, 230-240V
5
3516322
Filter dryer, (2) inlet, .25”
6
3516360
Tank, receiver
7
3516456
Coil, condenser, 3/4 HP
5
6
7
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
15
International F5 & F15 Series Service and Installation Manual
Fluorescent Light Fixture
7
1
Key
Part#
Description
-
000-406-0039
Complete assembly, 60"
000-406-0037
Complete assembly, 36”
000-406-0038
Complete assembly, 48”
1
313-146-0032
cap, end, top mtg, pigtail, -rem.
2
313-146-0033
cap, end, top mtg, blank, -rem.
3
376-A0M-0055
diffuser, fluor. light, 36”
376-A0M-0056
diffuser, fluor. light, 48"
376-A0M-0057
diffuser, fluor. light, 60"
2193907
lamp, fluorescent, 36”
2193908
lamp, fluorescent, 48”
2193909
lamp, fluorescent, 60"
5
2193939
lamp holder, left
6
2193940
lamp holder, right
7
9321266
screw, #8-32 x .50
8
2183613
pigtail, male, 3.5”, rem. ballast
9
9321010
nut, hex, starlock, s/s, #6-32
-
2194992
Ballast, rapid start 36” lamp
8
9
2
5
4
7
4
6
3
Base Door Assembly
1
5
4
Key Part#
Description
-
000-187-0066
complete door assy., right, 19”, 18.75” x 25.72”
000-187-0067
complete door assy., left, 19”, 18.75” x 25.72”
000-187-0068
complete door assy., right, 24”, 23.75” x 25.72”
000-187-0069
complete door assy., left, 24”, 23.75” x 25.72”
000-187-006A
complete door assy., right, 27”, 26.75” x 25.72”
000-187-006B
complete door assy., left, 27”, 26.75” x 25.72”
000-187-006C
complete door assy., right, 32”, 31.75” x 25.72”
000-187-006D
complete door assy., left, 32”, 31.75” x 25.72”
1701183
gasket, door, 19”
1701184
gasket, door, 24”
1701185
gasket, door, 27”
1701186
gasket, door, 32”
3234072
hinge, door, top/LH, bottom/RH
3
1
4
5
3
2
16
4
3234073
hinge, door, top/RH, bottom/LH
5
3234391
hinge, cabinet, L-shaped
6
9321107
bushing, nylon, hinge pin
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
International F5 & F15 Series Service and Installation Manual
F15 Base Evaporator Assembly
1
4
2
3
6
5
9
8
7
Key
1
2
3
4
5
6
7
8
9
-
Part Number
000-248-0033
2160024
2160025
3516095
030-232-0003
MCP00140
030-233-0001
000-BNH-0030
030-234-0003
030-233-0002
2184317
2194808
2194809
Description
Coil Assembly, R404A, Ref
Guard, fan, 4.7"
Fan, axiel, 230V
Coil, evaporator
Back, evaporator, enclosure
Expansion valve, 1/4, R-404a
Side, coil, angled, Rt
Drip pan, evaporator
Front, coil
Side, coil, angled, Lt
Harness, coil
Probe, Defrost, Danfoss, Control
Probe, Temp, Sensor, Danfoss
F15 Dual Pressure Control Assy.
Key
1
2
1
2
Part Number
Varies per destination
Varies per destination
Varies per destination
Description
Dual pressure control
Control
Rocker switch
Miscellaneous Replacement Parts
Part Number
Display Cases
3516172
031-264-0000
3516090
3516091
2193942
3516173
2184063
2195301
2162692
039-304-0030
000-BBO-0030
PMK00011
000-BBO-0032
MCP00142
MCP00141
MCP00158
2194400
3516135
2194536
3516084
F15 Base
Varies per
destination
3234645
Description
Blade, fan, Lexan, clear
Bracket, fan motor, blower coil
Coil, evaporator, 48”
Coil, evaporator, 72”
Control, pressure, low
Fan Guard
Harness, elec., power to ballasts
Line Filter
Motor, fan, 240V
Pan, drip, evap coil, 42” with flat bottom
Pan, drip, evap coil, 42” w/ recessed drain
Pan, drip, evap coil, 72” with flat bottom
Pan, drip, evap coil, 72” w/ recessed drain
Solenoid coil 240V
Solenoid valve, 240V
Solenoid valve connector
Switch, rocker, 240V
Thermometer, hanging, 4”
Thermostat, in-39.5D/out-22.5D
Valve, expansion, 1/2 ton, R404A
Cord/plug assembly
Leg, 6” with mount plate (4 used on 48” —
6 used on 72”)
Louver, 18”, 17.94 x 26.34
356-303-0031
Mirror Glass
3455418
Mirror, glass, top, 72”
Shelving & Misc. Parts — Serview Bases
3234290
Shelf support, plastic, plug 1”
3977984
Shelf, wire, 19” door, 14.38 x 25.25
3977998
Shelf, wire, 24” door, 19.38 x 25.25
3978014
Shelf, wire, 27” door, 22.56 x 25.25
3977983
Shelf, wire, 32” door, 27.38 x 25.25
9321132
Stud, wall side, for shelf support, 1/4x1.50
9321040
Stud, coil side, for shelf support
Shelving for Mirror Back Display Cases
3977993
Shelf, wire, 15.75” x 43.25” (M)
3978061
Shelf, wire, 15.75” x 67.25” (M)
3978025
Shelf, wire, 21.75” x 43.25” (M)
3978062
Shelf, wire, 21.75” x 67.25” (M)
Shelving for See Thru & Pass Thru Display Cases
3978026
Shelf, wire, 17.75” x 43.25” (S&P)
3978063
Shelf, wire, 17.75” x 67.25” (S&P)
3978027
Shelf, wire, 23.75” x 43.25” (S&P)
3978064
Shelf, wire, 23.75” x 67.25” (S&P)
(M) = Mirror Back • (S&P) = See Thru & Pass Thru
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
17
International F5 & F15 Series Service and Installation Manual
Wiring Diagram: Self-Contained F5 & F15 Series
N
18
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
International F5 & F15 Series Service and Installation Manual
Standard Labor Guidelines To Repair Or Replace Parts On Delfield Equipment
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
• A maximum of 1-hour is allowed to diagnose a defective component.
• A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed. Actual travel to be charged.
• Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or correcting and
end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work Authorization from Delfield.
You must submit the number with the service claim.
• Actual repair time will be paid at or below guidline.
• Parts on the critcal stock list must be air freighted at the expense of the service agent.
Labor Up To 1-Hour Is Allowed To Replace
• Infinite Switch
• Contactor/Relay
• Door Jamb Switch
• Transformer
• Solenoid Coil
• Evaporator/Condenser Fan Motor and Blade
• Hi-limit/Thermal Protector Switch
• Circulating Fan Motor and Blade
• Fan Delay/Defrost Termination Switch
• Digital Control
• Compressor Start Components and Overload Protector
• Water Level Sensor/Probe
• Defrost Timer
• Door Hinges, Locks, and Gaskets
• Thermostat
• Condensate Element
• Thermometer
• Springs/Lowerator
• Gear Motor
Labor Up To 2 Hours To Replace
• Drawer Tracks/Cartridges
• Defrost Element
• Pressure Control
• Heating Element
• Solenoid Valve
• Locate/Repair Leak
Labor Up To3 Hours To Replace
• EPR or CPR Valve
• Condenser or Evaporator Coil
• Expansion Valve
• Cap Tube
Labor Up To 4 Hours To Replace
• Compressor
-- This includes recovery of refrigerant and leak check.
-- $55.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings, solder,
brazing rod, nitrogen, or similar fees).
Refrigerants
• R22 A maximum of $4.00/lb. or 25¢/oz. will be reimbursed.
• R134A A maximum of $7.00/lb. or 44¢/oz. will be reimbursed.
• R404A A maximum of $16.00/lb. or $1.00/oz. will be reimbursed.
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
19
Covington, TN
Mt. Pleasant, MI
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous customer
service reps by having your model number and serial number available at the time
of your call (800) 733-8829.
Model:________________________ S/N: _______________________
Installation Date:________________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com
Register your Delfield warranty
online. Go to www.delfield.com
under the service tab to complete.
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2013 The Delfield Company. All rights reserved. Printed in the U.S.A.
DM5_15int 09/13
XXXXXXX
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement