B A DL205 E C

B A DL205 E C
DL205 ERROR CODES
APPENDIX
B
In This Appendix...
Error Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B–2
Appendix B: Error Codes
1
B
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
DL205 Error Code
Description
E003
SOFTWARE
TIME-OUT
If the program scan time exceeds the time allotted to the watchdog timer, this error will
occur. SP51 will be on and the error code will be stored in V7755. To correct this problem
add RSTWT instructions in FOR NEXT loops and subroutines or use AUX 55 to extend the
time allotted to the watchdog timer.
E041
CPU BATTERY LOW
The CPU battery is low and should be replaced. SP43 will be on and the error code will be
stored in V7757.
E099
PROGRAM
MEMORY EXCEEDED
If the compiled program length exceeds the amount of available CPU RAM this error will
occur. SP52 will be on and the error code will be stored in V7755. Reduce the size of the
application program.
E104
WRITE FAILED
A write to the CPU was not successful. Disconnect the power, remove the CPU, and make
sure the EEPROM is not write protected. If the EEPROM is not write protected, make sure
the EEPROM is installed correctly. If both conditions are OK, replace the CPU.
E151
BAD COMMAND
E155
RAM FAILURE
A parity error has occurred in the application program. SP44 will be on and the error code
will be stored in V7755. This problem may possibly be due to electrical noise. Clear the
memory and download the program again. Correct any grounding problems. If the error
returns replace the EEPROM or the CPU.
A checksum error has occurred in the system RAM. SP44 will be on and the error code will
be stored in V7755. This problem may possibly be due to a low battery, electrical noise or a
CPU RAM failure. Clear the memory and download the program again. Correct any
grounding problems. If the error returns replace the CPU.
E202
MISSING I/O
MODULE
An I/O module has failed to communicate with the CPU or is missing from the base. SP45
will be on and the error code will be stored in V7756. Run AUX42 to determine the slot and
base location of the module reporting the error.
E210
POWER FAULT
A short duration power drop-out occurred on the main power line supplying power to the
base.
E250
COMMUNICATION FAILURE
IN THE I/O CHAIN
A failure has occurred in the local I/O system. The problem could be in the base I/O bus or
the base power supply. SP45 will be on and the error code will be stored in V7755. Run
AUX42 to determine the base location reporting the error.
E252
NEW I/O CFG
This error occurs when the auto configuration check is turned on in the CPU and the actual
I/O configuration has changed either by moving modules in a base or changing types of
modules in a base. You can return the modules to the original position/types or run AUX45
to accept the new configuration. SP47 will be on and the error code will be stored in V7755.
E262
I/O OUT OF RANGE
An out of range I/O address has been encountered in the application program. Correct the
invalid address in the program. SP45 will be on and the error code will be stored in V7755.
E312
HP COMM
ERROR 2
A data error was encountered during communications with the CPU. Clear the error and
retry the request. If the error continues check the cabling between the two devices, replace
the handheld programmer, then if necessary replace the CPU. SP46 will be on and the error
code will be stored in V7756.
B–2
DL205 User Manual, 4th Edition, Rev. B
Appendix B: Error Codes
DL205 Error Code
Description
E313
HP COMM
ERROR 3
An address error was encountered during communications with the CPU. Clear the error and
retry the request. If the error continues, check the cabling between the two devices; replace
the handheld programmer; then, if necessary, replace the CPU.
SP46 will be on and the error code will be stored in V7756.
E316
HP COMM ERROR 6
A mode error was encountered during communications with the CPU. Clear the error and
retry the request. If the error continues, replace the handheld programmer; then if necessary,
replace the CPU. SP46 will be on and the error code will be stored in V7756.
E320
HP COMM TIME-OUT
The CPU did not respond to the handheld programmer communication request. Check to
ensure cabling is correct and not defective. Power cycle the system; If the error continues,
replace the CPU first and then the handheld programmer, if necessary.
E321
COMM ERROR
A data error was encountered during communication with the CPU. Check to insure cabling
is correct and not defective. Power cycle the system and, if the error continues, replace the
CPU first and then the handheld programmer, if necessary.
E4**
NO PROGRAM
A syntax error exists in the application program. The most common is a missing END
statement. Run AUX21 to determine which one of the E4** series of errors is being flagged.
SP52 will be on and the error code will be stored in V7755.
E401
MISSING END STATEMENT
All application programs must terminate with an END statement. Enter the END statement in
appropriate location in your program. SP52 will be on and the error code will be stored in
V7755.
E402
MISSING LBL
A GOTO, GTS, MOVMC or LDLBL instruction was used without the appropriate label. Refer
to the programming manual for details on these instructions.
SP52 will be on and the error code will be stored in V7755.
E403
MISSING RET (DL240 ONLY)
A subroutine in the program does not end with the RET instruction.
SP52 will be on and the error code will be stored in V7755.
E404
MISSING FOR
(DL240, DL250-1, DL260)
A NEXT instruction does not have the corresponding FOR instruction.
SP52 will be on and the error code will be stored in V7755.
E405
MISSING NEXT
(DL240/250–1/260)
A FOR instruction does not have the corresponding NEXT instruction.
SP52 will be on and the error code will be stored in V7755.
E406
MISSING IRT
An interrupt routine in the program does not end with the IRT instruction.
SP52 will be on and the error code will be stored in V7755.
E412
SBR/LBL>64
(DL240/250–1/260)
There is greater than 64 SBR, LBL or DLBL instructions in the program. This error is also
returned if there is greater than 128 GTS or GOTO instructions used in the program.
SP52 will be on and the error code will be stored in V7755.
DL205 User Manual, 4th Edition, Rev. B
1
B
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
B–3
Appendix B: DL205 Error Codes
1
B
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
DL205 Error Code
Description
E413
FOR/NEXT>64
(DL240/250–1/260)
There is greater than 64 FOR/NEXT loops in the application program. SP52 will be on and
the error code will be stored in V7755.
E421
DUPLICATE STAGE
REFERENCE
Two or more SG or ISG labels exist in the application program with the same number. A
unique number must be allowed for each Stage and Initial Stage. SP52 will be on and the
error code will be stored in V7755.
E422
DUPLICATE
SBR/LBL REFERENCE
Two or more SBR or LBL instructions exist in the application program with the same
number. A unique number must be allowed for each Subroutine and Label. SP52 will be on
and the error code will be stored in V7755.
E423
NESTED LOOPS
(DL240/250–1/260)
Nested loops (programming one FOR/NEXT loop inside of another) is not allowed in the
DL240/250–1/260 series. SP52 will be on and the error code will be stored in V7755.
E431
INVALID ISG/SG
ADDRESS
An ISG or SG must not be programmed after the end statement such as in a subroutine.
SP52 will be on and the error code will be stored in V7755.
E432
INVALID JUMP
(GOTO) ADDRESS
(DL240/250–1/260)
E433
INVALID SBR
ADDRESS
(DL240/250–1/260)
E435
INVALID RT
ADDRESS
(DL240/250–1/260)
An LBL that corresponds to a GOTO instruction must not be programmed after the end
statement such as in a subroutine. SP52 will be on and the error code will be stored in
V7755.
An SBR must be programmed after the end statement, not in the main body of the program
or in an interrupt routine. SP52 will be on and the error code will be stored in V7755.
An RT must be programmed after the end statement, not in the main body of the program or
in an interrupt routine. SP52 will be on and the error code will be stored in V7755.
E436
INVALID INT
ADDRESS
An INT must be programmed after the end statement, not in the main body of the program.
SP52 will be on and the error code will be stored in V7755.
E438
INVALID IRT
ADDRESS
An IRT must be programmed after the end statement, not in the main body of the program.
SP52 will be on and the error code will be stored in V7755.
E440
INVALID DATA
ADDRESS
Either the DLBL instruction has been programmed in the main program area (not after the
END statement), or the DLBL instruction is on a rung containing input contact(s).
E441
ACON/NCON
(DL240/250–1/260)
An ACON or NCON must be programmed after the end statement, not in the main body of
the program. SP52 will be on and the error code will be stored in V7755.
B–4
DL205 User Manual, 4th Edition, Rev. B
Appendix B: DL205 Error Codes
DL205 Error Codes
Description
E451
BAD MLS/MLR
MLS instructions must be numbered in ascending order from top to bottom.
E452
X AS COIL
An X data type is being used as a coil output.
E453
MISSING T/C
A timer or counter contact is being used where the associated timer or counter does not
exist.
E454
BAD TMRA
One of the contacts is missing from a TMRA instruction.
E455
BAD CNT
One of the contacts is missing from a CNT or UDC instruction.
E456
BAD SR
One of the contacts is missing from the SR instruction.
E461
STACK OVERFLOW
More than nine levels of logic have been stored on the stack.
Check the use of OR STR and AND STR instructions.
E462
STACK
UNDERFLOW
An unmatched number of logic levels have been stored on the stack.
Ensure the number of AND STR and OR STR instructions match the number of STR
instructions.
E463
LOGIC ERROR
A STR instruction was not used to begin a rung of ladder logic.
E464
MISSING CKT
A rung of ladder logic is not terminated properly.
E471
DUPLICATE COIL
REFERENCE
Two or more OUT instructions reference the same I/O point.
E472
DUPLICATE TMR
REFERENCE
Two or more TMR instructions reference the same number.
DL205 User Manual, 4th Edition, Rev. B
1
B
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
B–5
Appendix B: DL205 Error Codes
1
B
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
DL205 Error Code
Description
E473
DUPLICATE CNT
REFERENCE
Two or more CNT instructions reference the same number.
E480
INVALID CV
ADDRESS
The CV instruction is used in a subroutine or program interrupt routine.
The CV instruction may only be used in the main program area (before the END statement).
E481
CONFLICTING
INSTRUCTIONS
An instruction exists between convergence stages.
E482
MAX. CV
INSTRUCTIONS
EXCEEDED
Number of CV instructions exceeds 17.
E483
INVALID CVJMP
ADDRESS
CVJMP has been used in a subroutine or a program interrupt routine.
E484
MISSING CV
INSTRUCTION
CVJMP is not preceded by the CV instruction.
A CVJMP must immediately follow the CV instruction.
E485
NO CVJMP
A CVJMP instruction is not placed between the CV and the SG, ISG, BLK, BEND, END
instruction.
E486
INVALID BCALL
ADDRESS
A BCALL is used in a subroutine or a program interrupt routine.
The BCALL instruction may only be used in the main program area (before the END
statement).
E487
MISSING BLK
INSTRUCTION
The BCALL instruction is not followed by a BLK instruction.
E488
INVALID BLK
ADDRESS
The BLK instruction is used in a subroutine or a program interrupt.
Another BLK instruction is used between the BCALL and the BEND instructions.
E489
DUPLICATED CR
REFERENCE
The control relay used for the BLK instruction is being used as an output elsewhere.
E490
MISSING SG
INSTRUCTION
The BLK instruction is not immediately followed by the SG instruction.
B–6
DL205 User Manual, 4th Edition, Rev. B
Appendix B: DL205 Error Codes
DL205 Error Code
Description
E491
INVALID ISG
INSTRUCTION
ADDRESS
There is an ISG instruction between the BLK and BEND instructions.
E492
INVALID BEND
ADDRESS
The BEND instruction is used in a subroutine or a program interrupt routine.
The BEND instruction is not followed by a BLK instruction.
E493
MISSING REQUIRED
INSTRUCTION
A [CV, SG, ISG, BLK, BEND] instruction must immediately follow the BEND instruction.
E494
MISSING BEND
INSTRUCTION
The BLK instruction is not followed by a BEND instruction.
E499
PRINT
INSTRUCTION
Invalid PRINT instruct usage.
Quotations and/or spaces were not entered or entered incorrectly.
E501
BAD ENTRY
An invalid keystroke or series of keystrokes was entered into the handheld programmer.
E502
BAD ADDRESS
An invalid or out of range address was entered into the handheld programmer.
E503
BAD COMMAND
An invalid instruction was entered into the handheld programmer.
E504
BAD REF/VAL
An invalid value or reference number was entered with an instruction.
E505
INVALID
INSTRUCTION
An invalid instruction was entered into the handheld programmer.
E506
INVALID
OPERATION
An invalid operation was attempted by the handheld programmer.
E520
BAD OP–RUN
An operation which is invalid in the RUN mode was attempted by the handheld programmer.
DL205 User Manual, 4th Edition, Rev. B
1
B
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
B–7
Appendix B: DL205 Error Codes
1
B
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
DL205 Error Code
Description
E521
BAD OP–TRUN
An operation which is invalid in the TEST RUN mode was attempted by the handheld
programmer.
E523
BAD OP–TPGM
An operation which is invalid in the TEST PROGRAM mode was attempted by the handheld
programmer.
E524
BAD OP–PGM
An operation which is invalid in the PROGRAM mode was attempted by the handheld
programmer.
E525
MODE SWITCH
(DL240/250–1/260)
An operation was attempted by the handheld programmer while the CPU mode switch was
in a position other than the TERM position.
E526
OFF LINE
The handheld programmer is in the OFFLINE mode.
To change to the ONLINE mode use the MODE key.
E527
ON LINE
The handheld programmer is in the ONLINE mode.
To change to the OFFLINE mode use the MODE key.
E528
CPU MODE
The operation attempted is not allowed during a Run Time Edit.
E540
CPU LOCKED
The CPU has been password locked. To unlock the CPU use AUX82 with the password.
E541
WRONG
PASSWORD
The password used to unlock the CPU with AUX82 was incorrect.
E542
PASSWORD RESET
The CPU powered up with an invalid password and reset the password to 00000000.
A password may be re-entered using AUX81.
E601
MEMORY FULL
Attempted to enter an instruction which required more memory than is available in the CPU.
E602
INSTRUCTION
MISSING
A search function was performed and the instruction was not found.
E604
REFERENCE
MISSING
A search function was performed and the reference was not found.
B–8
DL205 User Manual, 4th Edition, Rev. B
Appendix B: DL205 Error Codes
DL205 Error Code
Description
E610
BAD I/O TYPE
The application program has referenced an I/O module as the incorrect type of module.
E620
OUT OF MEMORY
An attempt to transfer more data between the CPU and handheld programmer than the
receiving device can hold.
DV-1000: mismatch between MOVMC and LBL instructions.
E621
EEPROM NOT
BLANK
An attempt to write to a non-blank EEPROM was made.
Erase the EEPROM and then retry the write.
E622
NO HPP EEPROM
A data transfer was attempted with no EEPROM (or possibly a faulty EEPROM) installed in
the handheld programmer.
E623
SYSTEM EEPROM
A function was requested with an EEPROM which contains system information only.
E624
V-MEMORY ONLY
A function was requested with an EEPROM which contains V-memory data only.
E625
PROGRAM ONLY
A function was requested with an EEPROM which contains program data only.
E627
BAD WRITE
An attempt to write to a write protected or faulty EEPROM was made.
Check the write protect jumper and replace the EEPROM if necessary.
E628
EEPROM TYPE ERROR
The wrong size EEPROM is being used.
The DL230 and DL240 CPUs use different size EEPROMs.
E640
COMPARE ERROR
A compare between the EEPROM and the CPU was found to be in error.
E650
HPP SYSTEM ERROR
A system error has occurred in the handheld programmer.
Power cycle the handheld programmer.
If the error returns, replace the handheld programmer.
E651
HPP ROM ERROR
A ROM error has occurred in the handheld programmer.
Power cycle the handheld programmer.
If the error returns, replace the handheld programmer.
E652
HPP RAM ERROR
A RAM error has occurred in the handheld programmer.
Power cycle the handheld programmer.
If the error returns, replace the handheld programmer.
DL205 User Manual, 4th Edition, Rev. B
1
B
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
B–9
Appendix B: DL205 Error Codes
Notes
1
B
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
B–10
DL205 User Manual, 4th Edition, Rev. B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement