Series 1620 – Single and Dual Pressure Switches Bulletin E-51

Series 1620 – Single and Dual Pressure Switches Bulletin E-51
Bulletin E-51
Series 1620 – Single and Dual Pressure Switches
®
Specifications - Installation and Operating Instructions
8-7/8
[225.43]
2X Ø9/32 [Ø7.14]
MOUNTING HOLE
7-3/4
[196.85]
1-1/2
[38.10]
Ø7/8 [Ø22.23]
OPENING FOR 1/2
CONDUIT
CONNECTION
11/16 [17.46]
1-17/64 [32.15]
Series 1620 Pressure Switch
INSTALLATION
1. Switch is normally calibrated for mounting in the vertical position with pressure
and electrical connections pointing down. If other mounting is desired, it should be
specified when ordering.
2. Two lugs with 9/32˝ diameter holes, 180 degrees apart on an 8-1/4˝ diameter circle
are provided.
3. The location selected should be free from excessive vibration and ambient
temperatures should not be above 130°.
OPERATION
1. General – Differential pressure acting on the power diaphragm rotates a channel,
compressing a calibrated spring. The rotation of the channel actuates a snap switch
when the set-point is reached, opening one set of electrical contacts and closing the
other.
2. Pressure Connections – Two 1/8˝ NPT female connections are provided. Make
appropriate connections as follows:
A. Differential Pressure – Connect tubing from source of greater pressure to high
pressure port and from lower source to low pressure port.
B. Positive Pressure (above atmospheric) – Connect tubing from pressure source to
high pressure port. Leave low pressure port vented to atmosphere.
C. Negative Pressure (vacuum) – Connect tubing from vacuum source to low pressure port. Leave high pressure port vented to atmosphere.
Note: When installing switch per paragraphs B or C in dusty environments, we recommend use of optional A-331 filter vent plug in the unused port. This will keep excess dirt from collecting inside switch.
3. Electrical Connections – Make wire connections for normally open or normally
closed operation to appropriate screw terminals on snap switch.
ADJUSTMENT
1. If switch has been furnished pre-set, mount it vertically or horizontally as specified.
Shifting the position of the switch will alter the set point. Because the set-point may
shift in transit it should be checked before placing it in service.
2. The effective area of either side of the power diaphragm is changed by the effect of
the sealing diaphragm. Thus, the actuating differential pressure setting must be made
with the total pressure for the service intended imposed on both sides of the diaphragm.
For example, a switch set to close a circuit at a differential pressure increase to 1˝ of
water with a total pressure of 1 PSIG will vary from the 1˝ of water setting if the total
pressure is increased to 2 PSIG. Also, a two or three percent variation will be noted if
a switch set for vacuum or below atmospheric pressure is used for pressure or above
atmospheric pressure control.
3. To establish the set-point, use a manometer or pressure gage in an appropriate
range and of known accuracy. Apply pressure slowly to allow equalization in all
branches of the system. Keep tubing lengths as short as possible.
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.
8-1/4
[209.55]
5-15/64
[132.95]
2X 45°
2X R4-5/16
[109.54]
3-1/64
[76.60]
4-9/32 [108.74]
3
[76.20]
1/8 FEMALE
NPT LOW PRESSURE
CONNECTION
SPECIFICATIONS
Service: Air and non-combustible,
compatible gases.
Wetted Materials: Consult factory.
Temperature Limits: -30 to 130°F
(-34.4 to 54.4°C).
Pressure Limits: Max. 50 in. w.c. (12.44
kPa) continuous, 2 psig (13.79 kPa)
surge.
Switch Type: 1626, Single-pole doublethrow (SPDT); 1627, two Single-pole
double-throw (SPDT) .
Repeatability: ±1%.
Electrical Rating: 15 A @ 120-480 VAC,
60 Hz. Resistive, 1/8 HP @ 125 VAC,1/4
HP @ 250 VAC, 60 Hz.
22.5°
1/8 FEMALE NPT
HIGH PRESSURE
CONNECTION
Electrical Connections: 3 screw type,
common, normally open and normally
closed.
Process Connections: 1/8˝ female NPT.
Mounting Orientation: Diaphragm in
vertical position. Consult factory for other
position orientations.
Set Point Adjustment: Screw
Adjustment.
Weight: Model 1626, 3 Ib, 9.8 oz (1.64
kg); Model 1627, 3 Ib, 11.8 oz (1.69 kg).
Agency Approvals: CE.
MODEL 1626, ALSO MODEL 1627 DUAL SWITCHES: OPERATING
RANGES, DEAD BANDS AND RATINGS.
Model (1626 Operating Approximate
Adj. Diff. Between
Dead Band
shown, 1627 Range
Set Points
similar)
in w.c.
Min.
Max.
(1627 only)
1626-1
.15 to 1.5 .10
.20
0.5
1626-5
.5 to 6.0
.15
.35
1.2
1626-10
2.0 to 11
.25
.65
2.3
1626-20
8.0 to 24
.50
1.20
5.0
Add –EXPL for explosion proof housing;
Add –WP for weather proof housing
4. Model 1626 – The set-point is changed by turning the adjusting nut clockwise to
increase and counter-clockwise to decrease. Model 1627 – The set-point of snap
switch No. 2 is established first using the adjusting nut as with the 1626 series. Next,
set snap switch No. 1 by turning the adjusting screw under the switch roller. Recheck
switch No. 2 and correct as necessary. If switch No. 2 needs re-adjustment a final
check of switch No. 1 should be made. The settings of the two switches affect one
another and both should be checked any time either is changed.
MAINTENANCE
No unusual precautions are required. Care should be taken to keep the switch
reasonably dry and free from dust or dirt. No lubrication required.
CAUTION: For use with air or compatible gases only.
Phone: 219/879-8000
www.dwyer-inst.com
Fax: 219/872-9057
e-mail: [email protected]
SERIES 1620 – DIMENSIONS
SEALING DIAPHRAGM
CALIBRATED RANGE SPRING
ADJUSTING NUT
ADJUSTING NUT
SEALING DIAPHRAGM
CALIBRATED RANGE SPRING
ADJUSTING NUT
ADJUSTING NUT
SNAP SWITCH
SNAP SWITCH
ADJUSTING SCREW
ADJUSTING SCREW
POWER DIAPHRAGM
POWER DIAPHRAGM
1/8 NPT FEMALE
1/8 NPT FEMALE
SHOWN WITH: ONE SINGLE POLE DOUBLE THROW SWITCHES
SHOWN WITH: TWO SINGLE POLE DOUBLE THROW SWITCHES
OPTIONAL ENCLOSURES
Weatherproof Housing
Note: Pressure and electrical connections must face down when mounted.
1-1/4
(31.75)
2-21/64
(59.13)
1/8 FEMALE NPT
LOW PRESSURE
CONNECTION
1-5/16
(33.34)
7
(177.80)
TYP
8-13/16
(223.82)
1/8 FEMALE NPT
HIGH PRESSURE
CONNECTION
1/2 FEMALE NPT
ELECTRICAL CONNECTION
1/2 (12.70)
CLEARANCE
FOR COVER
REMOVAL
9-9/16 (242.89)
10-1/2 (266.70)
11-5/8 (295.28)
3-5/64 (78.18)
4-57/64
(124.22)
Explosion-proof Housing
Class I, Groups C & D; Class II, Groups E, F & G; Class III
Warning: To reduce the risk of ignition of the hazardous atmosphere, conduit seals must be installed within 18˝ of this enclosure.
Disconnect enclosure from supply circuit before opening. Keep assembly tight during operation.
Ø7/16 (11.11) MOUNTING
HOLE TYP 4 PLACES
BREATHER
11
(279.40)
6
2-1/8 (152.40)
(53.98)
12-1/8
(307.98)
5-1/2
(139.70) 13-5/8
(346.08)
3-1/2
(88.90)
3/4 FEMALE NPT
ELECTRICAL
CONNECTION
1/8 FEMALE NPT
HIGH PRESSURE
CONNECTION
DRAIN
10-3/4 (273.05)
12 (304.80)
1/8 FEMALE NPT
LOW PRESSURE
CONNECTION
1-3/4 (44.45)
CLEARANCE FOR
COVER REMOVAL
©Copyright 2015 Dwyer Instruments, Inc.
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.
3/4
3-1/2 (19.05)
(88.90)
8-1/4
(209.55)
Printed in U.S.A. 10/15
FR# 440199-00 Rev. 6
Phone: 219/879-8000
www.dwyer-inst.com
Fax: 219/872-9057
e-mail: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement