RCP2
Slider
Type
Mini
Standard
Controllers
Integrated
Rod
Type
RCP2
ROBO Cylinder
RCP2-GRSS
Model
Specification
Items
RCP2
Series
GRSS
ROBO Cylinder, 2-Finger Gripper, Mini Slider Type, Actuator Width 42mm, Pulse Motor
I
Type
Encoder type
20P
Motor type
30
8
Deceleration Ratio
Stroke
I: Incremental
20P: Pulse motor, 30:1/30
8: 8mm
deceleration (4mm per side)
* T he Simple absolute 20  size
ratio
encoder is also
considered type "I".
* See page Pre-47 for details on the model descriptions.
Applicable controller
Cable length
P1: PCON-PL/PO/SE
PSEL
P3:PCON-CA
PMEC/PSEP
MSEP
N:None
Options
NM: Non-motor end
FB: Flange bracket
SB: Shaft bracket
P: 1m
S: 3m
M: 5m
X:Custom Length
„„Gripping Force vs. Current Limit
The gripping (pushing) force can be adjusted freely
Mini
within the range of current limits of 20% to 70%.
Standard
L1
Controllers
Integrated
Table/
Arm/
Flat Type
L2
* Operate with the L1 distance up to 40mm.
* The gripping force value in the graph below is when both
L1 and L2 are at 0 mm. (For gripping force reference per
L1 distance, see page A-87.)
The gripping force value is the sum of gripping forces of
both fingers.
Mini
Standard
16
Gripper/
Rotary
Type
Gripping force (N)
14
Appendix
P.5
Linear
Servo
Type
SplashProof
Type
8
6
4
2
0
(1) The maximum opening/closing speed indicates the operating speed on one side. The relative operating speed
is twice this value.
(2) The maximum gripping force is the sum of the gripping forces of both fingers, at a gripping point where there
is no offset or overhang distance. The work piece weight that can be actually moved depends on the friction
coefficient between the gripper fingers and the work piece, as well as on the shape of the work piece. As a rough
guide, a work piece's weight should not exceed 1/10 to 1/20 of the gripping force. (See page A-86 for details.)
(3) The rated acceleration while moving is 0.3G.
Cleanroom
Type
12
10
0
10
20
30
40
50
Current Limit (% ratio)
* Please note that, when gripping (pushing), the speed is fixed at
5mm/s.
Actuator Specifications
„„Lead and Payload
„„ Stroke and Max. Opening/Closing Speed
Model number
Deceleration Ratio
Maximum Gripping
Force (N)
RCP2-GRSS-I-20P-30-8- ➀ - ➁ - ➂
30
14
(7 per side)
Stroke
Stroke
(mm)
8
(4 per side)
Stroke
8
(mm)
Deceleration ratio
78
(per side)
30
(Unit: mm/s)
Cable Length
Stroke
(mm)
Standard price
8
—
Type
Standard
(Robot Cables)
Special length
Servo
Motor
(24V)
Servo
Motor
(200V)
70
* The gripping force graph above shows reference numbers.
Please allow margins up to ± 15%.
Code explanation ➀ Applicable Controller ➁ Cable length ➂ Options
Pulse
Motor
60
Cable symbol
P (1m)
S (3m)
M (5m)
X06 (6m) ~ X10 (10m)
X11 (11m) ~ X15 (15m)
X16 (16m) ~ X20 (20m)
Standard price
—
—
—
—
—
—
* The standard cable is the motor-encoder integrated robot cable.
* See page A-59 for cables for maintenance.
Actuator Specifications
 Options
Name
Non-motor end specification
Flange bracket
Shaft bracket
Linear
Servo
Motor
373
RCP2-GRSS
Option code
NM
FB
SB
See page
➝ A-52
➝ A-43
➝ A-55
Standard price
—
—
—
Item
Description
Drive System
Positioning repeatability
Backlash
Lost motion
Guide
Allowable static load moment
Weight
Ambient operating temperature, humidity
Worm gear + helical gear + helical rack
±0.01mm
0.2mm or less per side (constantly pressed out by a spring)
0.05mm or less per side
Linear guide
Ma: 0.5 N·m, Mb: 0.5 N·m, Mc: 1.5 N·m
0.2kg
0 to 40oC, 85% RH or less (Non-condensing)
RCP2
ROBO Cylinder
Dimensional Drawings
www.intelligentactuator.com
CAD drawings can be downloaded
from the website.
2D
CAD
Appendix
P.15
*The opening side of the slider is the home position.
(*1) Connect the motor-encoder integrated cable here. See page A-59 for details on cables.
Slider
Type
Mini
Standard
Controllers
Integrated
2-ø3 +0.03
depth 3
0
17
(same for opposite side)
Rod
Type
17
8.5
8-M3 dapth 5
4
43
Mini
(same for opposite side)
Cable joint
connector*1
Standard
2-3 +0.05
depth 3
0
Controllers
Integrated
24
2-ø3h7 ( - 0.010 )
71
(same for opposite side)
0
1.5
Table/
Arm/
Flat Type
9
ø3 +0.03
depth 3
0
Standard
34
35
Gripper/
Rotary
Type
17
MAX 13.5
MIN 5.5
0
4
8.5
47
9 - 0.05
8-M3 depth 5
4
13.9
Mini
2
4.2
5
42
2-M3 depth 4
2-ø3 +0.03
depth 3
0
Secure at least 100
(same for opposite side)
4-M3 depth 5
(same for opposite side)
2-3
+0.05
0
Linear
Servo
Type
3 +0.05
depth 3
0
depth 3
(same for opposite side)
Cleanroom
Type
Weight (kg)
0.2
SplashProof
Type
Applicable Controllers
RCP2 series actuators can be operated with the controllers indicated below. Select the type according to your intended application.
Name
External
view
Model number
Features
Maximum number of
positioning points
AC100V
AC200V
PMEC-C-20PI- -2-
Easy-to-use controller, even for beginners
PSEP-C-20PI- -2-0
Simple controller operable with the same
signal as a solenoid valve
Solenoid valve multi-axis type
PIO specification
MSEP-C- -~- -2-0
Positioner type based on PIO control,
allowing up to 8 axes to be connected
Solenoid valve multi-axis type
Network specification
MSEP-C- -~- -0-0
Field network-ready positioner type,
allowing up to 8 axes to be connected
256 points
Positioner type
High-output specification
PCON-CA-20PI- -2-0
Equipped with a high-output driver
Positioner type based on PIO control
512 points
Pulse-train type
High-output specification
PCON-CA-20PI-PL-2-0
Equipped with a high-output driver
Pulse-train input type
(—)
Field network type
High-output specification
PCON-CA-20PI- -0-0
Equipped with a high-output driver
Supporting 7 major field networks
768 points
Pulse Train Input Type
(Differential Line Driver)
PCON-PL-20PI- -2-0
Pulse train input type with differential line
driver support
Pulse Train Input Type
(Open Collector)
PCON-PO-20PI- -2-0
Pulse train input type with open collector
support
Serial Communication Type
PCON-SE-20PI-N-0-0
Dedicated Serial Communication
PSEL-CS-1-20PI- -2-0
Programmed operation is possible.
Can operate up to 2 axes
Solenoid Valve Type
Program
Control Type
* This is for the single-axis PSEL.
*
* indicates number of axes (1 to 8). *
Input
power
3 points
Power-supply Standard Reference
capacity
price
page
Refer to
P541
—
➝ P537
Refer to
P555
—
➝ P547
Refer to
P572
—
➝ P563
—
DC24V
Refer to
P618
—
Pulse
Motor
➝ P607
—
Servo
Motor
(24V)
—
(—)
Refer to
P628
64 points
1,500 points
—
➝ P623
—
Refer to
P671
indicates I/O type (NP/PN).
* indicates power supply voltage (1: 100V / 2: 100~240V).
indicates field network specification symbol. *  indicates N (NPN specification) or P (PNP specification) symbol.
RCP2-GRSS
—
Servo
Motor
(200V)
➝ P665
Linear
Servo
Motor
374
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement