06p4598
Install the server in
the rack, if required
®
xSeries 220
Installation Guide
Install options:
• Drives
• Microprocessors
• Adapters
• Memory
Cable the server
and options
Welcome. . .
Thank you for buying an
IBM xSeries server.
This server Installation Guide
contains information for setting
up and configuring your server.
Start the server
Did the server
start correctly?
No
Yes
For detailed information
about your server, view the
User's Reference on the
Documentation CD.
You can also find the most
current information about your
server on the IBM Web site at:
http://www.ibm.com/pc/support
Use ServerGuide™
to setup and
configure hardware
Did configuration
complete?
Go to the Server Support
flow chart
No
Yes
Use
ServerGuide to
install operating
system?
Yes
Use ServerGuide to
install applications,
such as IBM systems
management software
and IBM ServeRAID
programs
System is ready to use.
Go to the Server Support
flow chart to register
and profile your server.
No
Go to the Web for Instructions,
http://www.ibm.com/pc/support
Server Support
Server working
properly?
Yes
Register and profile your server
After you register and profile, you will be able to:
• Diagnose problems using the IBM Online Assistant
• Participate in the IBM discussion forum
• Receive e-mail notifications of technical updates
related to your profiled products
No
Check all cables for loose connections
and verify that all optional devices you
installed are on the ServerProven list.
You can view the ServerProven list at:
Register at: http://www.ibm.com/pc/register
Profile at: http://www.ibm.com/pc/support
http://www.ibm.com/pc/compat
Problem
solved?
Yes
No
You can view a list of
IBM Help Center phone numbers at:
http://www.ibm.com/pc/support
Use the troubleshooting
information provided with
your server to determine
the cause of the problem
and the action to take.
Problem
solved?
Yes
No
Flash the latest levels of BIOS,
service processor, diagnostics,
and RAID code.
You can download this code at:
http://www.ibm.com/pc/support
Yes
Problem
solved?
No
Phone an
IBM Help Center
IBM® xSeries 220
IBM
Installation Guide
SC06-P459-80
NOTE
Before using this information and the product it supports, be sure to read the general information in
“Appendix A. Product warranties and notices,” on page 49.
First Edition (October 2000)
© Copyright International Business Machines Corporation 2000. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with
IBM Corp.
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Chapter 4.Configuring your server . . . . . 39
Using the ServerGuide CDs . . . . . . . . . . . . . . . . . . . . . . . 39
Handling static sensitive devices . . . . . . xi
Chapter 1.Introduction . . . . . . . . . . . . . . . . 1
Features and specifications . . . . . . . . . . . . . . . . . . . . . . . .
Notices used in this book . . . . . . . . . . . . . . . . . . . . . . . . . .
Major components of the xSeries 220 server . . . . . . . . . .
System board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System board option connectors . . . . . . . . . . . . . . . . .
System board internal cable connectors . . . . . . . . . . .
System board external port connectors . . . . . . . . . . .
System board jumpers and switches . . . . . . . . . . . . .
2
3
3
4
4
5
5
6
Chapter 2.Installing options . . . . . . . . . . . . 9
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
System reliability considerations . . . . . . . . . . . . . . . . . 9
Removing the side cover . . . . . . . . . . . . . . . . . . . . . . . . . 10
Removing the support bracket assembly. . . . . . . . . . . . 10
Working with adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adapter considerations . . . . . . . . . . . . . . . . . . . . . . . . 13
Installing an adapter . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing memory modules . . . . . . . . . . . . . . . . . . . . . . 16
Internal drive bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Preinstallation steps (all bays) . . . . . . . . . . . . . . . . . . . . . 19
Installing a drive in bay 1, 2, 3, or 4 . . . . . . . . . . . . . . . . 20
Installing a hard disk drive . . . . . . . . . . . . . . . . . . . . . . . 22
Installing a non-hot-swap hard disk drive in bay 5, 6, or 7
22
Installing a hot-swap hard disk drive in bay 5, 6, or 7. 23
Installing a microprocessor . . . . . . . . . . . . . . . . . . . . . . . 26
Installing the cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cabling the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Chapter 3.Server power, controls, and
indicators . . . . . . . . . . . . . . . . . . . . . . . . . 35
Turning on the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Turning off the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Server controls and indicators. . . . . . . . . . . . . . . . . . . . . 37
© Copyright IBM Corp. 2000
iii
Chapter 5.Solving problems . . . . . . . . . . . 41
Diagnostic tools overview . . . . . . . . . . . . . . . . . . . . . . . .
POST beep code descriptions. . . . . . . . . . . . . . . . . . . . . .
POST error messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ServerGuide startup problems . . . . . . . . . . . . . . . . . . . .
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
42
43
44
45
Appendix A. Product warranties and
notices . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Warranty Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
IBM Statement of Limited Warranty for United States,
Puerto Rico, and Canada (Part 1 - General Terms) . 49
IBM Statement of Warranty Worldwide except United
States, Puerto Rico, and Canada (Part 1 – General
Terms). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Part 2 - Worldwide Country-Unique Terms . . . . . . . 55
Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Edition notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Processing date data . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Electronic emission notices . . . . . . . . . . . . . . . . . . . . . . . 60
Federal Communications Commission (FCC)
Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Industry Canada Class A emission compliance
statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Australia and New Zealand Class A statement. . . . 61
United Kingdom telecommunications safety
requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
European Union EMC Directive conformance
statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Taiwan electrical emission statement . . . . . . . . . . . . 62
Japanese Voluntary Control Council for Interference
(VCCI) statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Power cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
iv
IBM® xSeries 220: Installation Guide
Safety
Before installing this product, read the Safety Information book.
Antes de instalar este produto, leia o Manual de Informações sobre Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs hæftet med sikkerhedsforskrifter, før du installerer dette produkt.
Lue Safety Information -kirjanen, ennen kuin asennat tämän tuotteen.
Avant de procéder à l'installation de ce produit, lisez le manuel Safety Information.
Vor Beginn der Installation die Broschüre mit Sicherheitshinweisen lesen.
Przed zainstalowaniem tego produktu należy przeczytać broszurę Informacje Dotyczące
Bezpieczeństwa.
Prima di installare questo prodotto, leggere l'opuscolo contenente le informazioni
sulla sicurezza.
© Copyright IBM Corp. 2000
v
Lees voordat u dit product installeert eerst het boekje met veiligheidsvoorschriften.
Les heftet om sikkerhetsinformasjon (Safety Information) før du installerer dette
produktet.
Antes de instalar este produto, leia o folheto Informações sobre Segurança.
Перед установкой продукта прочтите брошюру по технике безопасности
(Safety Information).
Pred inštaláciou tohto produktu si pre ítajte Informa nú brožúrku o bezpe nosti.
Preden namestite ta izdelek, preberite knjižico Varnostne informacije.
Antes de instalar este producto, lea la Información de Seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Installálás el tt olvassa el a Biztonsági el írások kézikönyvét !
vi
IBM® xSeries 220: Installation Guide
Statement 1
Danger
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
•
Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical storm.
•
Connect all power cords to a properly wired and grounded electrical outlet.
•
Connect to properly wired outlets any equipment that will be attached to
this product.
•
When possible, use one hand only to connect or disconnect signal cables.
•
Never turn on any equipment when there is evidence of fire, water, or
structural damage.
•
Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless instructed
otherwise in the installation and configuration procedures.
•
Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.
To connect:
To disconnect:
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
2. First, remove power cords from outlets.
3. Attach signal cables to connectors.
3. Remove signal cables from connectors.
4. Attach power cords to outlets.
4. Remove all cables from devices.
5. Turn device ON.
vii
Statement 2
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has a
module containing a lithium battery, replace it only with the same module type
made by the same manufacturer. The battery contains lithium and can explode if
not properly used, handled, or disposed of.
Do not:
•
Throw or immerse into water.
•
Heat to more than 100 C (212 F)
•
Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Statement 3
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
•
Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
•
Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
Danger
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note
the following. Laser radiation when open. Do not stare into the beam, do not view
directly with optical instruments, and avoid direct exposure to the beam.
viii
IBM® xSeries 220: Installation Guide
Statement 4
≥18 kg (39.7 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
CAUTION:
Use safe practices when lifting.
Statement 5
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current from
the device, ensure that all power cords are disconnected from the power source.
2
1
ix
x
IBM® xSeries 220: Installation Guide
Handling static sensitive devices
Attention: Static electricity can damage electronic devices and your system. To avoid
damage, keep static sensitive devices in their static-protective bag until you are ready
to install them.
To reduce the possibility of electrostatic discharge, observe the following precautions:
•
Limit your movement. Movement can cause static electricity to build up around
you.
•
Handle the device carefully, holding it by its edges or its frame.
•
Do not touch solder joints, pins, or exposed printed circuitry.
•
Do not leave the device where others can handle and possibly damage the
device.
•
While the device is still in its anti-static package, touch it to an unpainted metal
part of the system unit for at least two seconds. (This drains static electricity
from the package and from your body.)
•
Remove the device from its package and install it directly into your system unit
without setting it down. If it is necessary to set the device down, place it on its
static-protective package. (If your device is an adapter, place it component side
up.) Do not place the device on your system unit cover or on a metal table.
•
Take additional care when handling devices during cold weather, as heating
reduces indoor humidity and increases static electricity.
© Copyright IBM Corp. 2000
xi
xii
IBM® xSeries 220: Installation Guide
Chapter 1. Introduction
Thank you for purchasing an IBM®
xSeries 220 server. This Installation Guide
provides the information that is needed to:
•
Set up and cable your server
•
Start and configure your server
•
Install your network operating system (NOS)
Packaged with the Installation Guide are software CDs that help you to configure
hardware, install device drivers, and install the network operating system.
Also included is an IBM xSeries Documentation CD, which provides detailed
information about your server.
Your server comes with a limited warranty and IBM Server Start Up Support. If you
have access to the World Wide Web, you can obtain up-to-date information about
your xSeries 220 model and other IBM server products at the following World Wide
Web address: http://www.ibm.com/eserver/xseries
To install your server in a rack, refer to the Tower-to-Rack Conversion Kit manual and
the Rack Installation Instructions that are provided with your optional rack hardware
for complete installation and removal instructions.
Record your product information in this table.
Product name
_____________________________________________
Machine type
_____________________________________________
Model number
_____________________________________________
Serial number
_____________________________________________
Key:
Serial number
(tower model only) __________________________
Manufacturer
(tower model only) __________________________
Phone number
(tower model only) __________________________
The server serial number is located on labels on the rear of the server and on the front
of the server below the bezel.
Note:
© Copyright IBM Corp. 2000
Your server keys cannot be duplicated by locksmiths. If you lose them, order
replacement keys from the key manufacturer. The key serial number and
telephone number of the manufacturer are on a tag that is attached to the
keys.
1
Features and specifications
Table 1 provides a summary of the features and specifications for your xSeries 220
server.
Microprocessor:
Video:
Environment:
•
Intel® Pentium® III
microprocessor with MMX™
technology and SIMD
extensions
•
S3 video controller (integrated
on system board)
•
•
Compatible with SVGA and
VGA
•
256 KB* ECC, level-2 cache
(min.)
•
8 MB SDRAM video memory
•
133 MHz front-side bus (FSB)
Size:
•
Support for up to two
microprocessors
•
Height: 470 mm (18.5 in.)
•
Depth: 508 mm (20 in.)
Memory:
•
Width: 165 mm (6.5 in.)
•
Standard: 128 MB*
•
•
Maximum: 4 GB*
Weight: approximately 19.5 Kg
(43 lb.) when fully configured
or 15.9 Kg (35 lb.) minimum
•
Type: 133 MHz, ECC, SDRAM,
registered DIMMs
Integrated functions:
Slots: 4 dual in-line
•
Ultra160 SCSI low voltage
differential (LVD) controller
•
One 10BASE-T/100BASE-TX
Intel Ethernet controller on the
system board
•
Drives standard:
•
Diskette: 1.44 MB
•
CD-ROM: 48X IDE
•
Supports hot-swap SCSI hard
disk drives (some models)
Expansion bays:
•
Server off: 10º to 43º C (50.0º
to 109.4º F). Maximum
altitude: 2133 m (6998.0 ft)
Humidity:
—
Server on: 8% to 80%
—
Server off: 8% to 80%
Heat output:
Approximate heat output in British
thermal units (Btu) per hour
•
Minimum configuration: 341 Btu
(100 watts)
•
Maximum configuration: 1604
Btu (470 watts)
Two Universal Serial Bus
(USB) ports
Electrical input:
•
Sine-wave input (50-60 Hz)
required
•
Input voltage low range:
Two 3.5-in. bays (one diskette
drive installed)
•
Mouse port
•
IDE controller port
Video port
Three 3.5-in. slim bays available •
in drive cage (some models
have a hard disk drive installed) Acoustical noise emissions:
•
Sound power, idling: 5.9 bel
PCI expansion slots:
maximum
•
One 330 watt autosensing (115-230 V
ac)
—
•
•
Power supply:
Server on: 10º to 32º C (50.0º
to 89.6º F). Altitude: 914 m
(2998.7 ft) to 2133 m (6998.0
ft)
Parallel port
Keyboard port
Two 33 MHz/32-bit
—
Two serial ports
•
•
Server on: 10º to 35º C (50.0º
to 95.0º F). Altitude: 0 to 914
m (2998.7 ft)
•
Two 5.25-in. bays (one CD-ROM
drive installed)
Three 33 MHz/64-bit
—
•
•
•
Air temperature:
•
Sound power, operating: 6.1
bel maximum
•
•
—
Minimum: 100 V ac
—
Maximum: 127 V ac
Input voltage high range:
—
Minimum: 200 V ac
—
Maximum: 240 V ac
Input kilovolt-amperes (kVA),
approximately:
—
Minimum: 0.08 kVA
—
Maximum: 0.52 kVA
Table 1. Features and specifications
*KB equals approximately 1000 bytes. MB equals approximately 1000000 bytes. GB
equals approximately 1000000000 bytes.
2
IBM® xSeries 220: Installation Guide
Notices used in this book
The caution and danger notices also appear in the multilingual Safety Information book
provided on the IBM xSeries Documentation CD that comes with your xSeries product.
Each notice is numbered for easy reference to the corresponding notices in the safety
book.
The following types of notices are used in this book:
•
Note: These notices provide important tips, guidance, or advice.
•
Important: These notices provide information or advice that might help you
avoid inconvenient or problem situations.
•
Attention: These notices indicate possible damage to programs, devices, or data.
An attention notice is placed just before the instruction or situation in which
damage could occur.
•
Caution: These notices indicate situations that can be potentially hazardous to
you. A caution notice is placed just before the description of a potentially
hazardous procedure step or situation.
•
Danger: These notices indicate situations that can be potentially lethal or
extremely hazardous to you. A danger notice is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
Major components of the xSeries 220 server
The orange color on components and labels in your server identifies hot-swap
components. This means that you can install or remove the component while the
system is running, provided that your system is configured to support this function.
For information about installing or removing a hot-swap component, see “Chapter 2.
Installing options,” on page 9.
The blue color on components and labels indicates touch points where a component
can be gripped, a latch moved, and so on.
Notes:
1. You must turn off the server before touching these touch points.
2. The illustrations in this document might differ slightly from your hardware.
The following illustration shows the locations of major components in your server.
Chapter 1. Introduction
3
Microprocessor
Rear adapter
retaining bracket
EMC shields
Filler
panels
Memory modules
Drive cage
Front adapter
support bracket
Support bracket assembly
Cover
System board
The illustrations in the following sections show the components on the system board.
System board option connectors
The following illustration identifies system-board connectors for user-installable
options.
Microprocessor 2
(U11)
Microprocessor 1
(U12)
Voltage regulator
module
(VRM) 2 (J12)
Voltage regulator
module
(VRM) 1 (J42)
DIMM 1
(J19)
DIMM 2
(J21)
DIMM 3
(J23)
DIMM 4
(J26)
PCI 1
(J29)
PCI 2
(J31)
Battery
(BH1)
PCI 5 (J40)
PCI 4 (J39)
PCI 3 (J35)
4
IBM® xSeries 220: Installation Guide
System
management
(J32)
Notes:
1. If your server and operating system support system-management functions and,
if the optional system-management adapter is installed in your server, the systemmanagement connector (J32) is dedicated for use by the system-management
adapter.
2. The system-management adapter is also known as the service processor.
System board internal cable connectors
The following illustration identifies system-board connectors for internal cables.
Microprocessor
fan 2 (J2)
Microprocessor
fan 1 (J3)
Fan 2
power
(J18)
Main power
(J1)
Diskette
drive (J27)
2
DASD I C
(J43)
Fan 1
power (J10)
IDE (J30)
Fan 3 power
(J22) (not used)
Wake on LAN
(J20)
SCSI channel
(J41)
System board external port connectors
The following illustration identifies system-board connectors for external devices.
Keyboard/mouse
USB
Serial A
Parallel
Serial B
Ethernet
Video
Chapter 1. Introduction
5
Note:
For information on adding external small computer system interface (SCSI)
devices to your server, refer to the User’s Reference on the IBM xSeries
Documentation CD.
System board jumpers and switches
The following illustration identifies the jumpers and switches on the system board.
Switch block
Flash ROM
page-swap
jumper (J38)
System board jumper blocks
Any jumper blocks on the system board that are not shown in the illustration are
reserved. For normal operation of the system, no jumpers should be installed on any
of the jumper blocks. Refer to the User’s Reference on the IBM xSeries Documentation CD
for information about the flash read-only memory (ROM) page-swap jumper.
System board switch block
The switch block contains microswitches 1 through 8. As pictured in this illustration,
switch 8 is at the right of the switch block, and switch 1 is at the left.
6
IBM® xSeries 220: Installation Guide
The following table describes the function for each switch. The default setting is Off
for all switches in the switch block.
Switch
number
8
Switch
description
Power-on password-override switch.
When toggled to the side that is opposite the default position, bypasses
the power-on password, if one is set.
7
Reserved.
6
Reserved.
5
Force power on.
4
Reserved.
3
Reserved.
2
Reserved.
1
Reserved.
Table 2. Switches 1 through 8
Chapter 1. Introduction
7
8
IBM® xSeries 220: Installation Guide
Chapter 2. Installing options
This chapter provides the basic information that is needed to install hardware options
in your server. If you need more detailed installation information, refer to the User’s
Reference on the IBM xSeries Documentation CD.
Before you begin
Before you begin to install options in your server, read the following information:
•
Become familiar with the safety and handling guidelines under “Handling static
sensitive devices” on page xi, and read the safety statements in “Safety” on page
v. These guidelines will help you work safely while working with your server or
options.
•
Make sure that you have an adequate number of properly grounded electrical
outlets for your server, monitor, and any other options that you intend to install.
•
Back up all important data before you make changes to disk drives.
•
Have a small, flat-blade screwdriver available.
•
For a list of supported options for your server, refer to
http://www.ibm.com/pc/compat on the World Wide Web.
System reliability considerations
To help ensure proper cooling and system reliability, make sure that:
•
Each of the drive bays has either a drive or a filler panel installed.
•
The cover is in place during normal operation, or is removed for no longer than
30 minutes while the server is operating.
•
There is space around the server to allow the server cooling system to work
properly. Leave about 127 mm (5 in.) of space around the front and rear of the
server.
•
Cables for optional adapters are routed according to the instructions that are
provided with the adapters.
•
A failed fan is replaced within one hour.
© Copyright IBM Corp. 2000
9
Removing the side cover
The following information describes how to remove the side cover.
Note:
The illustrations in this document might differ slightly from your hardware.
Cover-release
latch
Key lock
To remove the left-side cover from the server, do the following:
1. Review the information in “Before you begin” on page 9.
2. Turn off the server and all attached devices, and disconnect all external cables and
power cords.
3. If necessary, unlock the server cover.
4. Pull out on the cover-release latch at the rear of the server; then, slide the cover
toward the rear of the server and remove it.
Attention: For proper cooling and airflow, replace the cover before turning on the
server. Operating the server for extended periods of time (over 30 minutes) with
the cover removed might damage server components.
5. For a tower model, rotate the stabilizing feet on the bottom of the server, and
place the server on its side to install or remove components.
Removing the support bracket assembly
When working with some options such as hard disk drives and microprocessors, you
must first remove the support bracket assembly to access the location of the option.
The support bracket assembly consists of a support bracket, an air baffle, and a fan.
10
IBM® xSeries 220: Installation Guide
To remove the support bracket assembly, do the following:
1. Review the safety precautions in “Safety” on page v.
2. Turn off the server and peripheral devices and disconnect all external cables and
power cords.
3. Remove the cover (see “Removing the side cover” on page 10 for details).
4. If your server is a non-hot-swap model, continue with step 6.
5. If your server is a hot-swap model, press down on the latches on either side of
connector J42, and remove the voltage regulator module (VRM) from connector
J42. (See “System board option connectors” on page 4 for connector locations.)
Note:
Remember to reinstall this VRM after you reinstall the support bracket
assembly.
6. Disconnect the fan cable (connector J10) from the system board. (See “System
board internal cable connectors” on page 5 for connector locations.)
Note:
Remember to reconnect this cable after you reinstall the support bracket
assembly.
7. Carefully pull up on the end of the support bracket assembly that is closer to the
rear of the server; then, rotate and lift the support bracket assembly out of the
server.
8. Store the support bracket assembly in a safe place.
Chapter 2. Installing options
11
Working with adapters
You can install up to five peripheral component interconnect (PCI) adapters in the PCI
slots on the system board.
Your server comes with an integrated video controller. When you install a video
adapter, the server BIOS automatically disables the integrated video controller.
The following illustration shows the location of the 33 MHz PCI expansion slots.
Note:
The illustrations in this document might differ slightly from your hardware.
PCI slot 1 32-bit
33 MHz (J29)
PCI slot 2 32-bit
33 MHz (J31)
PCI slot 3 64-bit
33 MHz (J35)
PCI slot 4 64-bit
33 MHz (J39)
PCI slot 5 64-bit
33 MHz (J40)
12
IBM® xSeries 220: Installation Guide
Adapter considerations
Before you install adapters, review the following:
•
Locate the documentation that comes with the adapter and follow those
instructions in addition to the instructions given in this chapter. If you need to
change switch or jumper settings on your adapter, follow the instructions that
come with the adapter.
•
You can install full-length adapters in all expansion slots.
•
You can install a 32-bit adapter in any of the PCI slots, but you might want to
install it in a 32-bit slot and use the 64-bit slots for 64-bit adapters.
•
Your server supports 5.0V and universal PCI adapters; it does not support 3.3V
adapters.
•
Your server uses a rotational interrupt technique to configure PCI adapters.
Because of this technique, you can install a variety of PCI adapters that currently
do not support sharing of PCI interrupts.
•
The server has two PCI buses. PCI slots 1 and 2 are on PCI bus A, and PCI slots
3, 4, and 5 are on PCI bus B.
Note:
PCI bus A is sometimes referred to as bus 0; PCI bus B is sometimes
referred to as bus 1.
The system scans PCI slots 1 through 5 to assign system resources; then, the
system starts (boots) the PCI devices in the following order: PCI slots 1 and 2,
system board SCSI devices, and then PCI slots 3 through 5.
•
If you plan to use the Wake on LAN (WOL) function in the server, you must
install a Wake on LAN-enabled network interface card (NIC adapter) in PCI slot
1, and install the Wake on LAN cable that comes with the Wake on LAN adapter
to connect this adapter to the system board. You must use a Wake on LANenabled adapter as identified in the xSeries 220 ServerProven list at
http://www.ibm.com/pc/compat/. Only PCI slot 1 supports a Wake on LANenabled adapter. For additional information on the Wake on LAN function,
adapter, and cables, refer to the documentation that comes with the Wake on
LAN adapter.
•
If you plan to use the optional system-management adapter function in the
server, you must install the optional system-management adapter in PCI slot 2.
Only PCI slot 2 supports the optional system-management adapter. For
additional information on the optional system-management adapter, refer to the
documentation that comes with the adapter.
Chapter 2. Installing options
13
Installing an adapter
Note:
The illustrations in this document might differ slightly from your hardware.
Expansion-slot
cover
Rear adapter
retaining
bracket
Adapter
Front adapter
support
bracket
Attention: When you handle electrostatic discharge (ESD) sensitive devices, take
precautions to avoid damage from static electricity. For details on handling these
devices, see “Handling static sensitive devices” on page xi.
To install an adapter, do the following:
1. Review the safety precautions in “Safety” on page v.
2. Turn off the server and peripheral devices and disconnect all external cables and
power cords.
3. Remove the cover (see “Removing the side cover” on page 10 for details).
4. Carefully remove the support bracket assembly from the server (see “Removing
the support bracket assembly” on page 10). Store the cover and the support
bracket assembly in a safe place.
5. Determine which expansion slot you will use for the adapter.
Note:
Check the instructions that come with the adapter for any requirements
or restrictions.
6. Remove the rear adapter retaining bracket from the server. If you are installing a
full-length adapter, rotate the front adapter support bracket to the open
(unlocked) position.
7. Remove the expansion-slot cover. Store it in a safe place for future use.
Attention: Expansion-slot covers must be installed on all vacant slots. This
maintains the electronic emission characteristics of the system and ensures proper
cooling of system components.
14
IBM® xSeries 220: Installation Guide
8. Refer to the documentation that comes with your adapter for any cabling
instructions. It might be easier for you to route cables before you install the
adapter.
9. Remove the adapter from the static-protective package.
Attention: Avoid touching the components and gold-edge connectors on the
adapter.
10. Place the adapter, component-side up, on a flat, static-protective surface.
11. Set any jumpers or switches as described by the adapter manufacturer.
12. Install the adapter:
a. Carefully grasp the adapter by its top edge or upper corners, and align it with
the expansion slot on the system board.
b. Press the adapter firmly into the expansion slot.
Attention: When you install an adapter in the server, be sure that it is
completely and correctly seated in the system-board connector before you
apply power. Incomplete insertion might cause damage to the system board
or the adapter.
c. When the adapter is fully seated, release the front adapter support bracket by
pushing inward on the latch. Make sure that the front adapter support
bracket holds the adapter securely in place.
d. If you opened the front adapter support bracket, rotate it to the closed
(locked) position; then, reinstall the rear adapter retaining bracket in the
server.
13. Connect any needed cables to the adapter.
Attention: Route cables so that they do not block the flow of air from the fans.
The following illustration shows how to reroute the SCSI cable. If you install a
ServeRAID™ adapter and intend to use it with hot-swap, hard disk internal
drives, remove the cable from the internal SCSI connector (J41) on the system
board and connect it to the ServeRAID adapter.
Note:
You can also install a ServeRAID adapter in non-hot-swap models;
however, non-hot-swap models do not support hot-swap hard disk
drives.
Chapter 2. Installing options
15
SCSI cable
ServeRAID
adapter
SCSI connector
(J41)
14. If you have other options to install or remove, do so now; otherwise, replace the
support bracket assembly and the side cover (see “Installing the cover” on page
31 for details).
Note:
If your server is a hot-swap model, reinstall the VRM in connector J42
after you reinstall the support bracket assembly.
15. Reconnect the external cables and power cords; then, turn on the server.
Installing memory modules
Your server comes with a dual in-line memory module (DIMM) that is installed on the
system board in DIMM slot 1 (connector J19).
Notes:
1. When installing additional memory modules, install the second memory module
in the connector labeled DIMM3 (J23), the third in DIMM2 (J21), and the fourth in
DIMM4 (J26). (See the following illustration for memory-connector locations.)
2. Your xSeries 220 server supports 128 MB, 256 MB, 512MB, and 1GB DIMMs. Your
server supports a maximum of 4GB of system memory. See the ServerProven list
at http://www.ibm.com/pc/us/compat for a list of memory modules for use
with your server.
3. Installing or removing DIMMs changes the configuration information in the
server. Therefore, after installing or removing a DIMM, you must save the new
configuration information by using the Configuration/Setup Utility program.
When you restart the server, the system displays a message that indicates that the
memory configuration has changed. Start the Configuration/Setup Utility
program and select Save Settings. Refer to the User’s Reference on the IBM xSeries
Documentation CD for more information.
16
IBM® xSeries 220: Installation Guide
Note:
The illustrations in this document might differ slightly from your hardware.
DIMM 1
DIMM connector 1
DIMM 2
DIMM connector 2
DIMM connector 3
DIMM connector 4
Attention: When you handle electrostatic discharge (ESD) sensitive devices, take
precautions to avoid damage from static electricity. For details on handling these
devices, see “Handling static sensitive devices” on page xi.
To install a DIMM, do the following:
1. Review the safety precautions in “Safety” on page v.
2. Turn off the server, and remove the power cords.
3. Remove the cover (see “Removing the side cover” on page 10 for details).
4. Select the connector in which to install the DIMM.
5. Touch the static-protective package containing the DIMM to any unpainted metal
surface on the server. Then, remove the DIMM from the package.
Attention: To avoid breaking the retaining clips or damaging the DIMM
connectors, handle the clips gently.
6. Install the DIMM:
a. Open the retaining clips on the connector.
b. Turn the DIMM so that the pins align correctly with the connector.
c. Insert the DIMM into the connector by pressing on one edge of the DIMM
and then on the other edge of the DIMM. Ensure that you press the DIMM
straight into the connector.
d. Make sure that the retaining clips are in the closed position. If a gap exists
between the DIMM and the retaining clips, the DIMM has not been properly
installed. In this case, open the retaining clips and remove the DIMM; then,
reinsert the DIMM.
7. If you have other options to install or remove, do so now.
8. Replace the cover (see “Installing the cover” on page 31 for details).
9. Reconnect the power cords, and turn on the server.
Chapter 2. Installing options
17
Internal drive bays
Internal drives are installed in bays. The bays of the xSeries 220 are in the front of the
server, as shown in the following illustration.
Note:
The illustrations in this document might differ slightly from your hardware.
Bay 1
Bay 2
Bay 3
Bay4
Bay 5
Bay 6
Bay 7
To remove or install a drive, you must turn off the server first, unless you are
removing or installing a hot-swap hard disk drive. Diskette drives, tape drives, and
CD-ROM drives are removable-media drives. You can install removable-media drives
in bays 1, 2, 3, and 4. You can install SCSI hard disk drives in bays 4, 5, 6, and 7.
•
Your server comes with a 3.5-inch, 1.44 MB diskette drive in bay 3, an integrated
drive electronics (IDE) CD-ROM drive in bay 1, and a hard disk drive in bay 7
(in some models).
•
The xSeries 220 server supports five 3.5-inch drives; however, the server
supports only one diskette drive.
•
The diskette drive uses 1 MB and 2 MB diskettes. For optimum use, format 1 MB
diskettes to 720 KB and format 2 MB diskettes to 1.44 MB.
•
The xSeries 220 server supports two 5.25-inch drives and four SCSI hard disk
drives. The server does not support IDE hard disk drives. Some models support
hot-swap hard disk drives. Other models support only non-hot-swap hard disk
drives. Refer to the documentation that comes with your server for additional
information.
Your server supports four 1-inch (26 mm) slim, 3.5-inch SCSI hard disk drives in
the hard disk drive bays (4, 5, 6, and 7). You can install four non-hot-swap hard
disk drives in the models that have the standard non-hot-swap drive cage. You
can install three hot-swap hard disk drives and one non-hot-swap hard disk
drive in the models that come with the hot-swap drive cage. Both the non-hot-
18
IBM® xSeries 220: Installation Guide
swap and hot-swap drive cages hold a maximum of three hard disk drives. The
drive cages comprise bays 5, 6, and 7.
•
Bay 2 comes without a device installed. This bay is for a 5.25-inch, half-high,
removable-media drive, such as a tape backup drive.
•
Bay 4 is for a 3.5-inch, slim, removable-media drive or SCSI hard disk drive.
Note:
The electromagnetic interference (EMI) integrity and cooling of the server are
both protected by having bays 1 through 4 covered or occupied. When you
install a drive, save the filler panel from the bay, in case you later remove the
drive and do not replace it with another.
Preinstallation steps (all bays)
Before you install drives in your server, verify that you have all the cables and any
other equipment specified in the documentation that comes with the drive. You might
also need to perform certain preinstallation activities. Some of the steps are required
only during the initial installation of an option.
1. Read “Safety” on page v, “Handling static sensitive devices” on page xi, and the
documentation that comes with your drive.
2. Choose the bay in which you want to install the drive.
3. Check the instructions that come with the drive to see if you need to set any
switches or jumpers on the drive.
Chapter 2. Installing options
19
Installing a drive in bay 1, 2, 3, or 4
EMC shield
Filler panel
To install a drive in bay 1, 2, 3, or 4, do the following:
1. Read the information in “Preinstallation steps (all bays)” on page 19.
2. Turn off the server and peripheral devices; then, remove the side cover (see
“Removing the side cover” on page 10 for details).
3. Insert a screwdriver into the slot on the right side of the filler panel, and remove
the filler panel from the server.
4. Insert a screwdriver into the slots on the front of the EMC shield, and remove the
EMC shield from the bay.
5. If the drive is a laser product, observe the following safety precaution.
20
IBM® xSeries 220: Installation Guide
Statement 3
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
•
Do not remove the covers. Removing the covers of the laser product
could result in exposure to hazardous laser radiation. There are no
serviceable parts inside the device.
•
Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode.
Note the following. Laser radiation when open. Do not stare into the beam, do
not view directly with optical instruments, and avoid direct exposure to the
beam.
6. Touch the static-protective bag containing the drive to any unpainted metal
surface on the server; then, remove the drive from the bag and place it on a staticprotective surface.
7. Set any jumpers or switches on the drive according to the documentation that
comes with the drive.
8. Push the drive into the bay.
9. If the drive is an IDE device, plug one connector of the IDE cable into the back of
the drive and the other end of the cable into the IDE connector (J30) on the system
board.
If the drive is a SCSI device, plug one connector of the SCSI cable into the back of
the drive and make sure that the other end of the cable is connected to the SCSI
connector (J41) on the system board.
Note:
Ensure that you route the SCSI cable so that it does not block the airflow
to the rear of the drives or over the microprocessors.
10. Connect a power cable to the back of the drive. The connectors are keyed and can
be inserted only one way.
11. If you are installing another drive, do so now. Otherwise, continue with the next
step.
12. If you have other options to install or remove, do so now; otherwise, replace the
cover (see “Installing the cover” on page 31 for details).
Chapter 2. Installing options
21
Installing a hard disk drive
Refer to the following sections to install a hard disk drive.
Attention:
•
When you handle electrostatic discharge (ESD) sensitive devices, take
precautions to avoid damage from static electricity. For details on handling these
devices, see “Handling static sensitive devices” on page xi.
•
To maintain proper system cooling, do not operate the server for more than two
minutes without either a drive or a filler panel installed in each bay.
Notes:
1. The illustrations in this document might differ slightly from your hardware.
2. If your server has a redundant array of independent disks (RAID) adapter
installed, refer to the information provided with the RAID adapter for
information about configuring a drive.
Installing a non-hot-swap hard disk drive in bay 5, 6, or 7
22
IBM® xSeries 220: Installation Guide
Note:
You can also install a non-hot-swap hard disk drive in bay 4. See “Installing a
drive in bay 1, 2, 3, or 4” on page 20 for instructions.
To install a non-hot-swap hard disk drive in bay 5, 6, or 7, do the following:
1. Read the information in “Preinstallation steps (all bays)” on page 19.
2. Turn off the server and peripheral devices, and disconnect all external cables and
power cords; then, remove the cover (see “Removing the side cover” on page 10
for details).
3. Carefully remove the support bracket assembly from the server (see “Removing
the support bracket assembly” on page 10). Store the cover and the support
bracket assembly in a safe place.
4. Rotate the drive cage upward. If your server has a hard disk drive installed in the
drive cage, disconnect the cables from the rear of the drive.
5. Remove the plastic bag that contains the drive rails and screws from inside the
drive cage.
6. Install rails on each drive in the drive cage:
a. Pull the blue slide rails out of the plastic bag.
b. Install the screws on the sides of the drive.
c. Align the rails on the drive with the guide rails in the drive bay.
d. Push the drive into the bay until it clicks into place.
7. Reinstall the drive cage in the server. Rotate the drive cage downward until it
snaps into place.
8. Connect the server SCSI and power cables to the rear of the drives.
Note:
Ensure that you route the SCSI cable so that it does not block the airflow
to the rear of the drives or over the microprocessors.
9. If you have other options to install or remove, do so now; otherwise, replace the
support bracket assembly and the side cover (see “Installing the cover” on page
31 for details).
Note:
If your server is a hot-swap model, reinstall the VRM in connector J42
after you reinstall the support bracket assembly.
Installing a hot-swap hard disk drive in bay 5, 6, or 7
If you purchased a hot-swap model, your server contains hardware that you can use
to replace a failed hard disk drive without turning off the server. Therefore, you have
the advantage of continuing to operate your system while a hard disk drive is
removed or installed. These drives are known as hot-swap drives. If these drives are
connected to an optional controller, such as a ServeRAID controller, that supports this
function, and if one of these drives becomes defective, the ServeRAID controller can
rebuild the data from that drive onto another hot-swap drive. Refer to the information
that comes with your ServeRAID controller for details.
Each hot-swap drive has two indicator lights: the hard disk drive activity light and the
hard disk drive status light. When the green hard disk drive activity light is flashing,
the controller is accessing the hard disk drive. When this occurs, the SCSI activity light
on the front of the server also illuminates. The SCSI activity light is illustrated and
described in “Server controls and indicators” on page 37. If the amber hard disk drive
status light for a drive is lit continuously, that individual drive is faulty and requires
replacement. When the hard disk drive status light indicates a drive fault, you can
replace a hot-swap drive without turning off the server.
Note:
The hard disk drive activity light is also known as the SCSI hard disk drive
activity light.
Chapter 2. Installing options
23
Each hot-swap drive that you plan to install must be mounted in a hot-swap-drive
tray. The drive must have a single connector attachment (SCA) connector. Hot-swapdrive trays come with hot-swap drives.
The hot-swap bays connect to a SCSI backplane. This backplane is the printed circuit
board behind the bay. The backplane controls the SCSI IDs for the hot-swap drives.
The following illustration shows the hot-swap-drive backplane component locations,
as viewed from the front of the server.
Note:
The illustrations in this document might differ slightly from your hardware.
Hard disk
drive activity
light (green)
Hard disk
drive status
light (amber)
SCSI hot-swap
hard disk drive
connector
Note:
The hard disk drive activity light and hard disk drive status light on the
backplane match the hard disk drive activity light and hard disk drive status
light on the hot-swap drive.
The following illustration shows the rear connectors on the hot-swap-drive
backplane, as viewed from the rear of the server.
SCSI cable
connector
SCSI power
cable connector
2
I C cable
connector
The following illustration shows how to install a hot-swap hard disk drive in the
server. When you install hot-swap hard disk drives, install them in the following
order: bay 7, bay 6, and bay 5.
24
IBM® xSeries 220: Installation Guide
Filler panel
Drive tray
assembly
Drive tray handle
(in open position)
Attention:
•
When you handle electrostatic discharge (ESD) sensitive devices, take
precautions to avoid damage from static electricity. For details on handling these
devices, see “Handling static sensitive devices” on page xi.
•
To maintain proper system cooling, do not operate the server for more than 10
minutes without either a drive or a filler panel installed in each bay.
To install a hot-swap hard disk drive in bay 5, 6, or 7, do the following:
1. Review “Before you begin” on page 9.
2. Read the information in “Preinstallation steps (all bays)” on page 19.
Note:
You do not have to turn off the server to install hot-swap hard disk drives
in these bays.
3. Remove the filler panel from one of the empty hot-swap bays by inserting your
finger into the depression at the left side of the filler panel and pulling it away
from the server.
4. Install the hard disk drive in the hot-swap bay:
a. Ensure that the tray handle is open (that is, perpendicular to the drive).
b. Align the drive tray assembly with the guide rails in the bay.
c. Gently push the drive tray assembly into the bay until the drive stops.
d. Push the tray handle to the closed (locked) position.
e. Check the hard disk drive status light to verify that the hard disk drive is
operating properly.
If the amber hard disk drive status light for a drive is lit continuously, that
individual drive is faulty and needs to be replaced. If the green hard disk
drive activity light is flashing, the drive is being accessed.
Note:
If your server has a ServeRAID controller, you might need to reconfigure
your disk arrays after installing hard disk drives. Refer to the information
that comes with your ServeRAID controller.
5. If you have other options to install or remove, do so now.
Chapter 2. Installing options
25
Installing a microprocessor
Your server comes with one microprocessor, which is installed in microprocessor
connector U12 (the microprocessor connector that is closer to the power supply). This
is the startup (boot) microprocessor. If you install a microprocessor in microprocessor
connector U11, that one becomes the startup microprocessor, and the microprocessor
that is installed in microprocessor connector U12 is the application microprocessor.
You must also install a VRM when you install a microprocessor.
Notes:
1. The illustrations in this document might differ slightly from your server.
2. If necessary, see “System board option connectors” on page 4 for connector
locations.
Attention:
•
To avoid damage and ensure proper server operation when you install a new or
additional microprocessor, use microprocessors that have the same cache size
and type and the same clock speed. Microprocessor internal clock frequencies
and external clock frequencies must be identical. See the ServerProven list at
http://www.ibm.com/pc/compat for a list of microprocessors for use with
your server.
•
When you handle electrostatic discharge (ESD) sensitive devices, take
precautions to avoid damage from static electricity. For details on handling these
devices, see “Handling static sensitive devices” on page xi.
To install an additional microprocessor, do the following:
1. Review the safety precautions in “Safety” on page v.
2. Turn off the server and peripheral devices and disconnect all external cables and
power cords; then, remove the cover (see “Removing the side cover” on page 10
for details).
3. Carefully remove the support bracket assembly from the server (see “Removing
the support bracket assembly” on page 10). Store the cover and the support
bracket assembly in a safe place.
4. Lift the release lever on the microprocessor connector, and remove the terminator
card from the microprocessor connector.
5. Install the microprocessor:
a. Touch the static-protective package containing the new microprocessor to any
unpainted metal surface on the server; then, remove the microprocessor from
the package.
b. Orient the microprocessor over the microprocessor connector, as shown in the
following illustration. Carefully press the microprocessor into the connector.
26
IBM® xSeries 220: Installation Guide
Microprocessor 2
connector
Terminator card
Microprocessor 2
Lever
Microprocessor
orientation indicator
Attention: To avoid bending the pins, do not use excessive force when pressing
the microprocessor into the connector.
6. Press the release lever down to lock the microprocessor into place.
7. If you are installing a microprocessor that has a speed of 933 MHz or higher,
continue with step 9 on page 29.
If you are installing a microprocessor that has a speed lower than 933 MHz,
continue with step 8 on page 28.
Chapter 2. Installing options
27
8. If you are installing a microprocessor that has a speed lower than 933 MHz, install
the heat sink onto the microprocessor:
VRM 2
(J12)
Terminator card
Microprocessor 1
Microprocessor 2
VRM 1
(J42)
Heat sink
Heat-sink
retainer
a. Peel the plastic protective strip off the bottom of the heat sink. Make sure that
the square of thermal material is still on the bottom of the heat sink.
b. Align and place the heat sink on top of the microprocessor.
c. Align and place the heat-sink retainer (clip) over the heat sink; then, snap it
into place.
d. Continue with step 10 on page 29.
28
IBM® xSeries 220: Installation Guide
9. If you are installing a microprocessor that has a speed of 933 MHz or higher,
install a fan sink on the microprocessor and connect the fan-sink power cable to
the system board:
VRM 2
(J12)
Terminator card
Microprocessor
fan 1 (J2)
Microprocessor
fan 2 (J3 )
Microprocessor
VRM 1
(J42)
Fan sink
Fan-sink
retainer
a. Peel the plastic protective strip off the bottom of the fan sink. Make sure that
the square of thermal material is still on the bottom of the fan sink.
b. Align and place the fan sink on top of the microprocessor.
c. Align and place the fan-sink retainer (clip) over the fan sink.
d. Insert a small, flat-blade screwdriver into the tab on the fan-sink retainer.
e. Press down and in with the screwdriver handle to snap the fan-sink retainer
into place in the slot on the microprocessor, over the fan sink.
f. Connect the built-in fan-sink power cable to the appropriate connector on the
system board:
•
If you installed the microprocessor in connector U11, connect the fansink power cable to connector J2.
•
If you installed the microprocessor in connector U12, connect the fansink power cable to connector J3.
10. Place the terminator card in the static-protective package that your new
microprocessor was shipped in, and store it in a safe place. You will need to install
the terminator card again if you ever remove the microprocessor and do not
replace it with another microprocessor.
11. Install the VRM that is included in the microprocessor kit.
Attention: Use of other VRMs might cause your server to overheat.
a. Center the VRM over the appropriate VRM connector:
(1) If you installed the microprocessor in connector U11, press down on the
latches on either side of connector J12, and install the VRM in connector
J12.
Chapter 2. Installing options
29
(2) If you installed the microprocessor in connector U12, press down on the
latches on either side of connector J42, and install the VRM in connector
J42.
Note:
If your server is a hot-swap model, reinstall the VRM in connector J42
after you reinstall the support bracket assembly.
b. Make sure that the VRM is oriented and aligned correctly.
c. Press the VRM into the connector.
Note:
If you remove the microprocessor later, remember to install the
terminator card in the appropriate microprocessor connector and to
remove the VRM from the appropriate VRM connector. Refer to the
User’s Reference on the IBM xSeries Documentation CD for details.
12. If you have other options to install or remove, do so now; otherwise, replace the
support bracket assembly.
13. Replace the cover (see “Installing the cover” on page 31 for details).
14. Reconnect the external cables and power cords; then, turn on the server.
30
IBM® xSeries 220: Installation Guide
Installing the cover
The following information describes the cover installation procedure.
Note:
The illustrations in this document might differ slightly from your hardware.
Cover-release
latch
Key lock
Note:
If you removed the support bracket assembly after you removed the cover,
reinstall it before you install the cover.
To install the server left-side cover:
1. Clear any cables that might impede the replacement of the cover.
2. Align the bottom tabs of the side cover with the matching slots in the server
chassis; then, insert the tabs into the slots.
3. Close the cover-release latch to pull the cover forward and lock the cover in place.
4. Make sure that the stabilizing feet are rotated outward so that they properly
support the server.
5. Reconnect the external cables and cords to the server; then, plug the power cords
into electrical outlets.
Chapter 2. Installing options
31
Cabling the server
When you cable the server, ensure that you route the power, keyboard, and mouse
cables through the two plastic cable ties on the rear of the server. Route the power
cable through the upper cable tie; route the keyboard and mouse cables through the
lower cable tie.
Notes:
1. The illustrations in this document might differ slightly from your hardware.
2. Refer to the documentation that comes with your options for additional cabling
instructions. It might be easier for you to route any cables before you install
certain options.
3. To install your server in a rack, refer to the Tower-to-Rack Conversion Kit manual
and the Rack Installation Instructions that are provided with your optional rack
hardware for complete installation and removal instructions.
4. Cable identifiers are printed on the cables that come with your server and
options. Use these identifiers to connect the cables to the correct connectors. For
example, the hard disk drive cables are labeled HDD.
Cabling the rear of the server
The following illustration shows the external cable-access areas for a typical server
configuration.
Power cord
Mouse
Keyboard
USB 1
USB 2
Serial A
Parallel
Serial B
Ethernet
Video
32
IBM® xSeries 220: Installation Guide
Routing cables through the cable-management assembly
Additionally, if you install your server in a rack, ensure that you route all the cables
through the cable-management assembly on the rack (see the following illustration).
Detailed cabling instructions are given in the Tower-to-Rack Conversion Kit manual that
comes with your optional rack hardware.
Cable strap
Cable retaining
bracket
Cable strap
Cable-management
assembly
Chapter 2. Installing options
33
34
IBM® xSeries 220: Installation Guide
Chapter 3. Server power, controls, and indicators
This chapter describes how to start the server, and what the controls and indicators
mean.
Turning on the server
Turning on the server refers to the act of plugging the power cord of your server into
the power source and starting the operating system.
The server can start in any of the following ways:
•
You can press the power-control button on the front of the server to start the
server.
Notes:
1. You can install a circular disk over the power-control button to prevent
accidental manual power-off. This disk, known as the power-control button
shield, comes with your server.
2. After you plug the power cord of your server into an electrical outlet, wait
approximately 20 seconds before pressing the power-control button. During
this time, the system is initializing; therefore, the power-control button does
not respond.
•
If the server is turned on and a power failure occurs, the server will start
automatically when power is restored.
•
The Wake on LAN feature will turn on the server at the set time (when a Magic
Packet is received), provided that all of the following conditions are met:
— AC power is present.
— The server is either off or shut down from an Advanced Configuration and
Power Interface (ACPI) operating system.
— The Wake on LAN feature is enabled in the Configuration/Setup Utility
program.
— The Wake on LAN adapter is installed in PCI slot 1 and is connected to the
system board with the 3-pin auxiliary power connector.
Note:
•
© Copyright IBM Corp. 2000
For more detailed information about these features, refer to the User’s
Reference on the IBM xSeries Documentation CD.
If the optional system-management adapter is installed in the server, the systemmanagement adapter can turn on the server.
35
Turning off the server
Turning off the server refers to the act of disconnecting the server from the power
source.
You can turn off the server in any of the following ways:
Statement 5
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current from
the device, ensure that all power cords are disconnected from the power source.
2
1
•
You can press the power-control button on the front of the server. If this feature
is supported by your operating system, this starts an orderly shutdown of the
operating system, and places the server in standby mode.
Note:
•
You might need to press and hold the power-control button for more than four
seconds to cause an immediate shutdown of the server and to force the power
off. You can use this feature if the operating system stops functioning.
•
You can disconnect the server power cords from the electrical outlets to shut off
all power to the server.
Note:
36
After turning off the server, wait at least five seconds before you press
the power-control button to turn on the server again.
IBM® xSeries 220: Installation Guide
After disconnecting the power cords, wait about 15 seconds for your
system to stop running. Watch for the power-on light on the front of the
server to stop blinking.
Server controls and indicators
The following illustrations show the controls and indicators on the front of the server.
CD-ROM
eject button
CD-ROM drive
activity light
Diskette-eject
button
Diskette drive
activity light
SCSI
activity light
Power-on
light
Power-control
button
System error
light
CD-ROM eject button: Press this button to release a CD from the drive.
CD-ROM drive activity light: When this light is on, it indicates that the CD-ROM
drive is in use.
Diskette-eject button: Press this button to release a diskette from the drive.
Diskette-drive activity light: When this light is on, it indicates that the diskette drive
is in use.
SCSI activity light: When this green light is flashing, the controller is accessing a SCSI
device; for example, a hard disk drive.
Note:
Hot-swap hard disk drives also have an activity light. This light is also known
as the SCSI hard disk drive activity light.
If your server has a ServeRAID controller and this light flashes slowly (one flash per
second), the drive is being rebuilt. When the light flashes rapidly (three flashes per
second), the controller is identifying the drive.
Power-on light: When this green light is on, system power is present in the server.
Power-control button: Press this button to manually turn the server on or off.
System error light: When this amber light is on, it indicates that a system error has
occurred. An amber error light on the interior of the server, adjacent to the faulty
component, will also be on to further isolate the error. Refer to the User’s Reference on
Chapter 3. Server power, controls, and indicators
37
the IBM xSeries Documentation CD for detailed information on using the Diagnostic
LEDs.
Cover-release latch: Slide this lever to release the cover.
Cover-release
latch
Key lock
38
IBM® xSeries 220: Installation Guide
Chapter 4. Configuring your server
The ServerGuide™ CDs provide software setup tools and installation tools that are
specifically designed for your IBM server. Use these CDs during the initial installation
of your server to configure basic hardware features and to simplify your network
operating system installation. (See “Using the ServerGuide CDs” for more
information.) The ServerGuide CDs also contain a collection of application programs,
which you can install after your server is up and running.
In addition to the ServerGuide CDs, you can use the following configuration
programs to customize your server hardware:
•
Configuration/Setup Utility
The Configuration/Setup Utility program is part of the basic input/output system
(BIOS) code that comes with your server. You can use this program to configure
serial and parallel port assignments, change interrupt request (IRQ) settings,
change the drive startup sequence, set the date and time, and set passwords.
•
SCSISelect Utility
With the built-in SCSISelect Utility program, you can configure the devices that
are attached to the integrated SCSI controller. Use this program to change
default values, resolve configuration conflicts, and perform a low-level format
on a SCSI hard disk drive.
•
PXE Boot Agent Utility
The Preboot eXecution Environment (PXE) Boot Agent Utility program is part of
the BIOS code that comes with your server. You can use this program to change
network startup (boot) protocols and startup (boot) order, to select operating
system wake up support, and to set menu wait times.
•
ServeRAID programs
If you have a ServeRAID adapter installed in your server, you must use the
ServeRAID configuration program to define and configure your disk-array
subsystem before you install your operating system.
Note:
Refer to the User’s Reference on the IBM xSeries Documentation CD for detailed
instructions for using the configuration programs.
Using the ServerGuide CDs
The ServerGuide CDs provide state-of-the-art programs to detect the server model
and hardware options that are installed, configure the server hardware, provide
device drivers, and install your network operating system (NOS).
Note:
If the ServerGuide CD does not start, see “ServerGuide startup problems” on
page 44.
1. Insert the Setup and Installation CD, and restart the server.
2. Follow the on-screen instructions to:
a. Select your language.
b. Select your keyboard layout and country.
c. View the overview to learn about ServerGuide features.
© Copyright IBM Corp. 2000
39
d. View the README file to review installation tips about your NOS and
adapter.
e. Start the setup and hardware configuration programs.
f. Start the NOS installation. You will need your copy of the NOS CD.
Note:
40
IBM® xSeries 220: Installation Guide
For information on the supported NOS versions, refer to the Setup and
Installation CD label.
Chapter 5. Solving problems
This section provides basic troubleshooting information to help you resolve some
common problems that might occur while setting up your server.
If you cannot locate and correct the problem using the information in this section,
refer to the User’s Reference on the IBM xSeries Documentation CD and the "Server
Support" flowchart in the front of this booklet for additional information.
Diagnostic tools overview
The following tools are available to help you identify and resolve hardware-related
problems:
•
Beep codes and error messages
The power-on self-test (POST) generates beep codes to indicate successful test
completion or the detection of a problem.
— One beep indicates successful completion of POST.
— More than one beep indicates that POST detected a problem. Error messages
also appear during startup if POST detects a hardware-configuration
problem.
See “POST beep code descriptions” on page 42 and “POST error messages” on
page 43 for more information.
•
Troubleshooting chart
This chart lists problem symptoms and suggested steps to correct the problems.
See the “Troubleshooting chart” on page 45 for more information.
•
Event/error logs
The POST error log contains the three most recent error codes and messages that
the system generated during POST. The system event/error log contains all
error messages that are issued during POST and all system status messages from
the system-management adapter.
To view the contents of the error logs, start the Configuration/Setup Utility
program; then, select Event/Error Logs from the main menu.
•
Diagnostic programs and error messages
The server diagnostic programs are stored in upgradeable read-only memory
(ROM) on the system board. These programs are the primary method of testing
the major components of your server.
Note:
© Copyright IBM Corp. 2000
Refer to the User’s Reference on the IBM xSeries Documentation CD for
more detailed information about the diagnostic programs.
41
POST beep code descriptions
POST emits one beep to signal successful completion. If POST detects a problem
during startup, other beep codes might occur. You can use the following beep code
descriptions to help identify and resolve problems that are detected during startup.
Note:
Refer to the User’s Reference on the IBM xSeries Documentation CD for more
detailed information about the POST beep codes.
Beep code
Descriptions of the POST beep codes
No beep
Call for service.
Continuous
If no video appears, the startup microprocessor failed. Verify that the startup microprocessor is
installed correctly. If it is, replace the startup microprocessor. If the problem persists, call for service.
One short
POST completed successfully. One beep also occurs after POST if you enter an incorrect password.
Two short
Follow the instructions that appear on the screen.
Three short
POST detected a system memory error. Verify that the memory is installed correctly. If it is, replace
the failing memory module.
Repeating short
The system board might contain a failing component.
1. Verify that the keyboard and pointing devices are connected properly.
2. Ensure that nothing is resting on the keyboard.
3. Disconnect the pointing device; then, restart the server. If the problem goes away, replace the
pointing device. If the problem remains, call for service.
One long and
one short
If the video controller on the system board is being used, call for service. If you installed an optional
video adapter, replace the failing adapter
One long and
two short
A video I/O adapter ROM is not readable, or the video subsystem is defective. If you installed an
optional video adapter, replace the failing adapter. If the problem remains, call for service.
One long and
three short
The system-board video subsystem has not detected a monitor connection to the server. Ensure that
the monitor is connected to the server. If the problem persists, replace the monitor.
Two long and
two short
POST does not support the optional video adapter. Replace the optional video adapter with one that
is supported by the server, or use the integrated video controller.
All other beep
codes
1. Verify that the system memory modules are installed correctly.
2. Turn off the server.
3. Disconnect all power cords.
4. Wait 30 seconds; then, reconnect all power cords and restart the server. If the problem remains,
call for service.
Table 3. POST beep code descriptions
42
IBM® xSeries 220: Installation Guide
POST error messages
The following table provides an abbreviated list of the error messages that might
appear during POST.
Note:
POST message
Refer to the User’s Reference on the IBM xSeries Documentation CD for more
detailed information about POST error messages.
Failing device or problem found
Suggested action
129
L1 cache of a microprocessor
Check the installation of your microprocessors.
162
Change in device configuration
Verify that your optional devices are turned on and
installed correctly.
163
Time of day has not been set
Set the correct date and time.
164
Change in memory configuration
Verify that your memory is installed properly; then, restart
the server and run the Configuration/Setup Utility
program.
201
Change in memory configuration
Verify that your memory is fully seated and installed
properly.
229
L2 cache of a microprocessor
Check the installation of your microprocessors.
289
Failing DIMM was disabled
Verify that your memory is correct for your server and that
it is installed properly.
301
Keyboard and keyboard controller
Ensure that the keyboard cable is connected and nothing is
resting on the keyboard keys.
962
Parallel port configuration error
Start the Configuration/Setup program and verify that the
parallel-port setting is correct.
11xx
Serial port error
Verify that the serial cable is connected correctly.
1162
Serial port configuration conflict
Start the Configuration/Setup program and ensure that the
IRQ and I/O port assignments needed by the serial port are
available.
1601
BIOS update needed
Download and install the latest system BIOS level.
1800
PCI adapter hardware interrupt
Start the Configuration/Setup program and verify that the
interrupt resource settings are correct.
2400
Video controller and memory
Verify that the monitor is connected correctly.
00019xxx
Processor x is not functioning or
failed the built-in test
Verify that processor x is installed correctly. If the problem
remains, replace processor x.
00180xxx
A PCI adapter requested a resource
that is not available
Start the Configuration/Setup program and ensure that the
resources needed by the PCI adapter are available.
012980xx
Data for processor x
Download and install the latest system BIOS level.
01298200
Microprocessor speed mismatch
Install microprocessors with identical speeds.
I9990305
POST could not find an operating
system.
Install your operating system.
303
2462
012981xx
Table 4. Abbreviated list of POST error messages
Chapter 5. Solving problems
43
ServerGuide startup problems
Look for the symptom in the left column of the chart. Probable solutions to the
problem are in the right column.
Setup
Setup and Installation CD
will not start.
Suggested action
•
Ensure that the system is a supported server with a startable (bootable) CD-ROM
drive.
•
If the startup (boot) sequence settings have been altered, ensure that the CD-ROM is
first in the boot sequence.
•
If more than one CD-ROM drive is installed, ensure that only one drive is set as the
primary drive. Start the CD from the primary drive.
ServeRAID program
cannot view all installed
drives - or - cannot
install NOS.
•
Ensure that there are no duplicate SCSI IDs or IRQ assignments.
•
Ensure that the hard disk drive is connected properly.
The Operating System
Installation program
continuously loops.
Free up more space on the hard disk drive.
ServerGuide will not
start your NOS CD.
Ensure that the NOS CD you have is supported by ServerGuide. See the Setup and Installation
CD label for a list of NOS versions supported.
Cannot install NOS option is grayed out.
Ensure that the NOS is supported on your server. If the NOS is supported, either there is no
logical drive defined (ServeRAID systems) or the ServerGuide System Partition is not
present. Run the ServerGuide setup and configuration program, and ensure that setup is
complete.
System Updates and
Applications CD
Get "time out" or
"Unknown host" errors
44
Suggested action
Be sure you have access to the Internet through FTP directly.
IBM® xSeries 220: Installation Guide
Troubleshooting chart
Notes:
1. Refer to the User’s Reference on the IBM xSeries Documentation CD for more
detailed troubleshooting charts.
2. If you cannot find the problem in the troubleshooting charts, run the diagnostic
programs. If you have run the diagnostic test programs, or if running the tests
does not reveal the problem, call for service.
Monitor problems
The screen is blank.
Suggested action
Verify that:
1. The server power cord is plugged into the server and a working electrical
outlet.
2. The monitor cables are connected properly.
3. The monitor is turned on and the Brightness and Contrast controls are adjusted
correctly.
If the items above are correct and the screen remains blank, call for service.
Attention: In some memory configurations, the 3-3-3 beep code might sound during
POST followed by a blank screen. If this occurs and the Boot Fail Count feature in
the Start Options of the Configuration/Setup Utility is set to Enabled (its default
setting), you must restart the server three times to force the system BIOS to reset the
memory connector or bank of connectors from Disabled to Enabled.
Only the cursor appears.
Call for service.
The monitor works when you
turn on the server, but goes
blank when you start some
application programs.
Verify that:
1. The primary monitor cable is connected to the video port.
2. You installed the necessary device drivers for the applications.
If the items above are correct and the screen remains blank, call for service.
Wavy, unreadable, rolling,
distorted screen, or screen jitter.
Some IBM monitors have their own self-tests. If you suspect a problem with your
monitor, refer to the information that comes with the monitor for adjusting and
testing instructions.
If the monitor self-tests show the monitor is OK, consider the location of the
monitor. Magnetic fields around other devices (such as transformers, appliances,
fluorescent lights, and other monitors) can cause screen jitter or wavy, unreadable,
rolling, or distorted screen images. If this happens, turn off the monitor. (Moving a
color monitor while it is turned on might cause screen discoloration.) Then move the
device and the monitor at least 305 mm (12 in.) apart. Turn on the monitor.
Notes:
1. To prevent diskette drive read/write errors, be sure the distance between
monitors and diskette drives is at least 76 mm (3 in.).
2. Non-IBM monitor cables might cause unpredictable problems.
3. An enhanced monitor cable with additional shielding is available for the 9521
and 9527 monitors. For information about the enhanced monitor cable, see your
IBM reseller or IBM marketing representative.
If the problem remains, call for service.
Wrong characters appear on the
screen.
If the wrong language is displayed, update the BIOS with the correct language.
If the problem remains, call for service.
Chapter 5. Solving problems
45
Power problems
The server does not power on.
Suggested action
Verify that:
1. The power cables are properly connected to the server.
2. The electrical outlet functions properly.
3. The type of memory that is installed is correct.
4. If you just installed an option, remove it, and restart the server. If the server
now powers on, you might have installed more options than the power supply
supports.
5. The LEDs on the power supply are on.
If the problem remains, call for service.
Microprocessor problems
The server emits a continuous
tone during POST.
Suggested action
The startup (boot) microprocessor is not working properly.
Verify that the startup microprocessor is seated properly. If it is, replace the startup
microprocessor.
If the problem remains, call for service.
Memory problems
The amount of memory
displayed is less than the
amount of memory installed.
Suggested action
Verify that:
1. The memory modules are seated properly.
2. You have installed the correct type of memory.
3. If you changed the memory, you updated the memory configuration with the
Configuration/Setup Utility program.
4. All banks of memory on the DIMMs are enabled. The server might have
automatically disabled a DIMM bank when it detected a problem or a DIMM
bank could have been manually disabled.
If the above items are correct, run the memory diagnostic program. The system
might have detected a bad memory module and automatically reallocated memory
to enable you to continue to operate. If the memory tests fail, call for service or
replace the failing DIMM.
Option problems
An IBM option that was just
installed does not work.
Suggested action
Verify that:
1. The option is designed for the server. Refer to the "Server Support" flowchart
for information about obtaining ServerProven™ compatibility information
from the World Wide Web.
2. You followed the installation instructions that came with the option.
3. The option is installed correctly.
4. You have not loosened any other installed options or cables.
5. You updated the configuration information in the Configuration/Setup Utility
program. Whenever memory or an option is changed, you must update the
configuration.
If the problem remains, call for service.
46
IBM® xSeries 220: Installation Guide
Expansion enclosure problems
The SCSI expansion enclosure
used to work, but does not work
now.
Suggested action
Verify that:
1. The cables for all external SCSI options are connected correctly.
2. The last option in each SCSI chain, or the end of the SCSI cable, is terminated
correctly.
3. Any external SCSI option is turned on. You must turn on an external SCSI
option before turning on the server.
For more information, see your SCSI and expansion enclosure documentation.
System-management adapter
problems
System-management adapter
manager reports a general
monitor failure
Suggested action
Disconnect the server from all electrical sources, wait for 30 seconds, reconnect the
server to the electrical sources, and restart the server.
If a problem remains, call for service.
Chapter 5. Solving problems
47
48
IBM® xSeries 220: Installation Guide
Appendix A. Product warranties and notices
This chapter contains warranty and emission notices. It also contains trademarks and
general-information notices.
Warranty Statements
The warranty statements consist of two parts: Part 1 and Part 2. Part 1 varies by
country. Part 2 is the same for all countries. Be sure to read both the Part 1 that applies
to your country and Part 2.
•
United States, Puerto Rico, and Canada (Z125-4753-05 11/97)
(page 49, Part 1 - General Terms)
•
Worldwide except Canada, United States, and Puerto Rico (Z125-5697-01 11/97)
(“Part 1 - General Terms,” on page 52)
•
Worldwide Country-Unique Terms
(“Part 2 - Worldwide Country-Unique Terms” on page 55)
IBM Statement of Limited Warranty for United States,
Puerto Rico, and Canada (Part 1 - General Terms)
This Statement of Limited Warranty includes Part 1 - General Terms and Part 2 Country-unique Terms. The terms of Part 2 may replace or modify those of Part 1.
The warranties provided by IBM in this Statement of Limited Warranty apply only to
Machines you purchase for your use, and not for resale, from IBM or your reseller.
The term "Machine" means an IBM machine, its features, conversions, upgrades,
elements, or accessories, or any combination of them. The term "Machine" does not
include any software programs, whether pre-loaded with the Machine, installed
subsequently or otherwise. Unless IBM specifies otherwise, the following warranties
apply only in the country where you acquire the Machine. Nothing in this Statement
of Warranty affects any statutory rights of consumers that cannot be waived or limited
by contract. If you have any questions, contact IBM or your reseller.
Machine - IBM
xSeries 220
Warranty Period*
•
Canada - Parts: Three (3) years Labor: Three (3) years
•
United States and Puerto Rico - Parts: Three (3) years Labor: One (1) year
IBM will provide warranty service without charge for:
1. parts and labor during the first year of the warranty period
2. parts only, on an exchange basis, in the second and third years of the warranty
period.
IBM will charge you for any labor it provides in performance of the repair or
replacement.
© Copyright IBM Corp. 2000
49
* Contact your place of purchase for warranty service information. Some IBM Machines are
eligible for on-site warranty service depending on the country where service is performed.
The IBM Warranty for Machines
IBM warrants that each Machine 1) is free from defects in materials and workmanship
and 2) conforms to IBM’s Official Published Specifications. The warranty period for a
Machine is a specified, fixed period commencing on its Date of Installation. The date
on your sales receipt is the Date of Installation, unless IBM or your reseller informs
you otherwise.
During the warranty period IBM or your reseller, if approved by IBM to provide
warranty service, will provide repair and exchange service for the Machine, without
charge, under the type of service designated for the Machine and will manage and
install engineering changes that apply to the Machine.
If a Machine does not function as warranted during the warranty period, and IBM or
your reseller are unable to either 1) make it do so or 2) replace it with one that is at
least functionally equivalent, you may return it to your place of purchase and your
money will be refunded. The replacement may not be new, but will be in good
working order.
Extent of Warranty
The warranty does not cover the repair or exchange of a Machine resulting from
misuse, accident, modification, unsuitable physical or operating environment,
improper maintenance by you, or failure caused by a product for which IBM is not
responsible. The warranty is voided by removal or alteration of Machine or parts
identification labels.
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND REPLACE
ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION
TO JURISDICTION. SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF EXPRESS OR IMPLIED WARRANTIES, SO
THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. IN
THAT EVENT, SUCH WARRANTIES ARE LIMITED IN DURATION TO THE
WARRANTY PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.
Items Not Covered by Warranty
IBM does not warrant uninterrupted or error-free operation of a Machine.
Unless specified otherwise, IBM provides non-IBM machines WITHOUT
WARRANTIES OF ANY KIND.
Any technical or other support provided for a Machine under warranty, such as
assistance via telephone with "how-to" questions and those regarding Machine set-up
and installation, will be provided WITHOUT WARRANTIES OF ANY KIND.
Warranty Service
To obtain warranty service for the Machine, contact your reseller or IBM. In the
United States, call IBM at 1-800-772-2227. In Canada, call IBM at 1-800-565-3344. (In
Toronto, call 416-383-3344.) You may be required to present proof of purchase.
50
IBM® xSeries 220: Installation Guide
IBM or your reseller provides certain types of repair and exchange service, either at
your location or at a service center, to keep Machines in, or restore them to,
conformance with their Specifications. IBM or your reseller will inform you of the
available types of service for a Machine based on its country of installation. IBM may
repair the failing Machine or exchange it at its discretion.
When warranty service involves the exchange of a Machine or part, the item IBM or
your reseller replaces becomes its property and the replacement becomes yours. You
represent that all removed items are genuine and unaltered. The replacement may not
be new, but will be in good working order and at least functionally equivalent to the
item replaced. The replacement assumes the warranty service status of the replaced
item.
Any feature, conversion, or upgrade IBM or your reseller services must be installed on
a Machine which is 1) for certain Machines, the designated, serial-numbered Machine
and 2) at an engineering-change level compatible with the feature, conversion, or
upgrade. Many features, conversions, or upgrades involve the removal of parts and
their return to IBM. A part that replaces a removed part will assume the warranty
service status of the removed part.
Before IBM or your reseller exchanges a Machine or part, you agree to remove all
features, parts, options, alterations, and attachments not under warranty service.
You also agree to
1. ensure that the Machine is free of any legal obligations or restrictions that prevent
its exchange;
2. obtain authorization from the owner to have IBM or your reseller service a
Machine that you do not own; and
3. where applicable, before service is provided
a. follow the problem determination, problem analysis, and service request
procedures that IBM or your reseller provides,
b. secure all programs, data, and funds contained in a Machine,
c. provide IBM or your reseller with sufficient, free, and safe access to your
facilities to permit them to fulfill their obligations, and
d. inform IBM or your reseller of changes in a Machine’s location.
IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM’s
possession or 2) in transit in those cases where IBM is responsible for the
transportation charges.
Neither IBM nor your reseller is responsible for any of your confidential, proprietary
or personal information contained in a Machine which you return to IBM or your
reseller for any reason. You should remove all such information from the Machine
prior to its return.
Production Status
Each IBM Machine is manufactured from new parts, or new and used parts. In some
cases, the Machine may not be new and may have been previously installed.
Regardless of the Machine’s production status, IBM’s appropriate warranty terms
apply.
Limitation of Liability
Circumstances may arise where, because of a default on IBM’s part or other liability,
you are entitled to recover damages from IBM. In each such instance, regardless of the
basis on which you are entitled to claim damages from IBM (including fundamental
Appendix A. Product warranties and notices
51
breach, negligence, misrepresentation, or other contract or tort claim), IBM is liable for
no more than
1. damages for bodily injury (including death) and damage to real property and
tangible personal property; and
2. the amount of any other actual direct damages, up to the greater of U.S. $100,000
(or equivalent in local currency) or the charges (if recurring, 12 months’ charges
apply) for the Machine that is the subject of the claim.
This limit also applies to IBM’s suppliers and your reseller. It is the maximum for
which IBM, its suppliers, and your reseller are collectively responsible.
UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE
FOLLOWING: 1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES
(OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2) LOSS OF,
OR DAMAGE TO, YOUR RECORDS OR DATA; OR 3) SPECIAL, INCIDENTAL,
OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL
DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF IBM, ITS
SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
IBM Statement of Warranty Worldwide except United
States, Puerto Rico, and Canada (Part 1 – General
Terms)
This Statement of Warranty includes Part 1 - General Terms and Part 2 - Countryunique Terms. The terms of Part 2 may replace or modify those of Part 1.The
warranties provided by IBM in this Statement of Warranty apply only to Machines
you purchase for your use, and not for resale, from IBM or your reseller. The term
"Machine" means an IBM machine, its features, conversions, upgrades, elements, or
accessories, or any combination of them. The term "Machine" does not include any
software programs, whether pre-loaded with the Machine, installed subsequently or
otherwise. Unless IBM specifies otherwise, the following warranties apply only in the
country where you acquire the Machine. Nothing in this Statement of Warranty
affects any statutory rights of consumers that cannot be waived or limited by contract.
If you have any questions, contact IBM or your reseller.
Machine - IBM
xSeries 220
Warranty Period* - Parts: Three (3) years Labor: Three (3) years
* Contact your place of purchase for warranty service information. Some IBM Machines are
eligible for on-site warranty service depending on the country where service is performed.
The IBM Warranty for Machines
IBM warrants that each Machine 1) is free from defects in materials and workmanship
and 2) conforms to IBM’s Official Published Specifications. The warranty period for a
Machine is a specified, fixed period commencing on its Date of Installation. The date
on your sales receipt is the Date of Installation, unless IBM or your reseller informs
you otherwise.
52
IBM® xSeries 220: Installation Guide
During the warranty period IBM or your reseller, if approved by IBM to provide
warranty service, will provide repair and exchange service for the Machine, without
charge, under the type of service designated for the Machine and will manage and
install engineering changes that apply to the Machine.
If a Machine does not function as warranted during the warranty period, and IBM or
your reseller are unable to either 1) make it do so or 2) replace it with one that is at
least functionally equivalent, you may return it to your place of purchase and your
money will be refunded. The replacement may not be new, but will be in good
working order.
Extent of Warranty
The warranty does not cover the repair or exchange of a Machine resulting from
misuse, accident, modification, unsuitable physical or operating environment,
improper maintenance by you, or failure caused by a product for which IBM is not
responsible. The warranty is voided by removal or alteration of Machine or parts
identification labels.
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND REPLACE
ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION
TO JURISDICTION. SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF EXPRESS OR IMPLIED WARRANTIES, SO
THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. IN
THAT EVENT, SUCH WARRANTIES ARE LIMITED IN DURATION TO THE
WARRANTY PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.
Items Not Covered by Warranty
IBM does not warrant uninterrupted or error-free operation of a Machine.
Unless specified otherwise, IBM provides non-IBM machines WITHOUT
WARRANTIES OF ANY KIND.
Any technical or other support provided for a Machine under warranty, such as
assistance via telephone with "how-to" questions and those regarding Machine set-up
and installation, will be provided WITHOUT WARRANTIES OF ANY KIND.
Warranty Service
To obtain warranty service for the Machine, contact your reseller or IBM. You may be
required to present proof of purchase.
IBM or your reseller provides certain types of repair and exchange service, either at
your location or at a service center, to keep Machines in, or restore them to,
conformance with their Specifications. IBM or your reseller will inform you of the
available types of service for a Machine based on its country of installation. IBM may
repair the failing Machine or exchange it at its discretion.
When warranty service involves the exchange of a Machine or part, the item IBM or
your reseller replaces becomes its property and the replacement becomes yours. You
represent that all removed items are genuine and unaltered. The replacement may not
be new, but will be in good working order and at least functionally equivalent to the
item replaced. The replacement assumes the warranty service status of the replaced
item.
Appendix A. Product warranties and notices
53
Any feature, conversion, or upgrade IBM or your reseller services must be installed on
a Machine which is 1) for certain Machines, the designated, serial-numbered Machine
and 2) at an engineering-change level compatible with the feature, conversion, or
upgrade. Many features, conversions, or upgrades involve the removal of parts and
their return to IBM. A part that replaces a removed part will assume the warranty
service status of the removed part.
Before IBM or your reseller exchanges a Machine or part, you agree to remove all
features, parts, options, alterations, and attachments not under warranty service.
You also agree to
1. ensure that the Machine is free of any legal obligations or restrictions that prevent
its exchange;
2. obtain authorization from the owner to have IBM or your reseller service a
Machine that you do not own; and
3. where applicable, before service is provided
a. follow the problem determination, problem analysis, and service request
procedures that IBM or your reseller provides,
b. secure all programs, data, and funds contained in a Machine,
c. provide IBM or your reseller with sufficient, free, and safe access to your
facilities to permit them to fulfill their obligations, and
d. inform IBM or your reseller of changes in a Machine’s location.
IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM’s
possession or 2) in transit in those cases where IBM is responsible for the
transportation charges.
Neither IBM nor your reseller is responsible for any of your confidential, proprietary
or personal information contained in a Machine which you return to IBM or your
reseller for any reason. You should remove all such information from the Machine
prior to its return.
Production Status
Each IBM Machine is manufactured from new parts, or new and used parts. In some
cases, the Machine may not be new and may have been previously installed.
Regardless of the Machine’s production status, IBM’s appropriate warranty terms
apply.
Limitation of Liability
Circumstances may arise where, because of a default on IBM’s part or other liability,
you are entitled to recover damages from IBM. In each such instance, regardless of the
basis on which you are entitled to claim damages from IBM (including fundamental
breach, negligence, misrepresentation, or other contract or tort claim), IBM is liable for
no more than
1. damages for bodily injury (including death) and damage to real property and
tangible personal property; and
2. the amount of any other actual direct damages, up to the greater of U.S. $100,000
(or equivalent in local currency) or the charges (if recurring, 12 months’ charges
apply) for the Machine that is the subject of the claim.
This limit also applies to IBM’s suppliers and your reseller. It is the maximum for
which IBM, its suppliers, and your reseller are collectively responsible.
54
IBM® xSeries 220: Installation Guide
UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE
FOLLOWING: 1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES
(OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2) LOSS OF,
OR DAMAGE TO, YOUR RECORDS OR DATA; OR 3) SPECIAL, INCIDENTAL,
OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL
DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF IBM, ITS
SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Part 2 - Worldwide Country-Unique Terms
ASIA PACIFIC
AUSTRALIA: The IBM Warranty for Machines: The following paragraph is added
to this Section:
The warranties specified in this Section are in addition to any rights you may have
under the Trade Practices Act 1974 or other legislation and are only limited to the
extent permitted by the applicable legislation.
Extent of Warranty: The following replaces the first and second sentences of this
Section:
The warranty does not cover the repair or exchange of a Machine resulting from
misuse, accident, modification, unsuitable physical or operating environment,
operation in other than the Specified Operating Environment, improper maintenance
by you, or failure caused by a product for which IBM is not responsible.
Limitation of Liability: The following is added to this Section:
Where IBM is in breach of a condition or warranty implied by the Trade Practices Act
1974, IBM’s liability is limited to the repair or replacement of the goods or the supply
of equivalent goods. Where that condition or warranty relates to right to sell, quiet
possession or clear title, or the goods are of a kind ordinarily acquired for personal,
domestic or household use or consumption, then none of the limitations in this
paragraph apply.
PEOPLE’S REPUBLIC OF CHINA: Governing Law: The following is added to this
Statement:
The laws of the State of New York govern this Statement.
INDIA: Limitation of Liability: The following replaces items 1 and 2 of this Section:
1. liability for bodily injury (including death) or damage to real property and
tangible personal property will be limited to that caused by IBM’s negligence;
2. as to any other actual damage arising in any situation involving nonperformance
by IBM pursuant to, or in any way related to the subject of this Statement of
Warranty, IBM’s liability will be limited to the charge paid by you for the
individual Machine that is the subject of the claim.
NEW ZEALAND: The IBM Warranty for Machines: The following paragraph is
added to this Section:
The warranties specified in this Section are in addition to any rights you may have
under the Consumer Guarantees Act 1993 or other legislation which cannot be
excluded or limited. The Consumer Guarantees Act 1993 will not apply in respect of
any goods which IBM provides, if you require the goods for the purposes of a
business as defined in that Act.
Limitation of Liability: The following is added to this Section:
Where Machines are not acquired for the purposes of a business as defined in the
Appendix A. Product warranties and notices
55
Consumer Guarantees Act 1993, the limitations in this Section are subject to the
limitations in that Act.
EUROPE, MIDDLE EAST, AFRICA (EMEA)
The following terms apply to all EMEA countries.
The terms of this Statement of Warranty apply to Machines purchased from an IBM
reseller. If you purchased this Machine from IBM, the terms and conditions of the
applicable IBM agreement prevail over this warranty statement.
Warranty Service
If you purchased an IBM Machine in Austria, Belgium, Denmark, Estonia, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,
Netherlands, Norway, Portugal, Spain, Sweden, Switzerland or United Kingdom, you
may obtain warranty service for that Machine in any of those countries from either (1)
an IBM reseller approved to perform warranty service or (2) from IBM.
If you purchased an IBM Personal Computer Machine in Albania, Armenia, Belarus,
Bosnia and Herzegovina, Bulgaria, Croatia, Czech Republic, Georgia, Hungary,
Kazakhstan, Kirghizia, Federal Republic of Yugoslavia, Former Yugoslav Republic of
Macedonia (FYROM), Moldova, Poland, Romania, Russia, Slovak Republic, Slovenia,
or Ukraine, you may obtain warranty service for that Machine in any of those
countries from either (1) an IBM reseller approved to perform warranty service or (2)
from IBM.
The applicable laws, Country-unique terms and competent court for this Statement
are those of the country in which the warranty service is being provided. However,
the laws of Austria govern this Statement if the warranty service is provided in
Albania, Armenia, Belarus, Bosnia and Herzegovina, Bulgaria, Croatia, Czech
Republic, Federal Republic of Yugoslavia, Georgia, Hungary, Kazakhstan, Kirghizia,
Former Yugoslav Republic of Macedonia (FYROM), Moldova, Poland, Romania,
Russia, Slovak Republic, Slovenia, and Ukraine.
The following terms apply to the country specified:
EGYPT: Limitation of Liability: The following replaces item 2 in this Section:
2. as to any other actual direct damages, IBM’s liability will be limited to the total
amount you paid for the Machine that is the subject of the claim.
Applicability of suppliers and resellers (unchanged).
FRANCE: Limitation of Liability: The following replaces the second sentence of the
first paragraph of this Section:
In such instances, regardless of the basis on which you are entitled to claim damages
from IBM, IBM is liable for no more than: (items 1 and 2 unchanged).
GERMANY: The IBM Warranty for Machines: The following replaces the first
sentence of the first paragraph of this Section:
The warranty for an IBM Machine covers the functionality of the Machine for its
normal use and the Machine’s conformity to its Specifications.
The following paragraphs are added to this Section:
The minimum warranty period for Machines is six months.
In case IBM or your reseller are unable to repair an IBM Machine, you can
alternatively ask for a partial refund as far as justified by the reduced value of the
unrepaired Machine or ask for a cancellation of the respective agreement for such
Machine and get your money refunded.
Extent of Warranty: The second paragraph does not apply.
56
IBM® xSeries 220: Installation Guide
Warranty Service: The following is added to this Section:
During the warranty period, transportation for delivery of the failing Machine to IBM
will be at IBM’s expense.
Production Status: The following paragraph replaces this Section:
Each Machine is newly manufactured. It may incorporate in addition to new parts, reused parts as well.
Limitation of Liability: The following is added to this Section:
The limitations and exclusions specified in the Statement of Warranty will not apply
to damages caused by IBM with fraud or gross negligence and for express warranty.
In item 2, replace "U.S. $100,000" with "1.000.000 DEM."
The following sentence is added to the end of the first paragraph of item 2:
IBM’s liability under this item is limited to the violation of essential contractual terms
in cases of ordinary negligence.
IRELAND: Extent of Warranty: The following is added to this Section:
Except as expressly provided in these terms and conditions, all statutory conditions,
including all warranties implied, but without prejudice to the generality of the
foregoing all warranties implied by the Sale of Goods Act 1893 or the Sale of Goods
and Supply of Services Act 1980 are hereby excluded.
Limitation of Liability: The following replaces items one and two of the first
paragraph of this Section:
1. death or personal injury or physical damage to your real property solely caused by
IBM’s negligence; and 2. the amount of any other actual direct damages, up to the
greater of Irish Pounds 75,000 or 125 percent of the charges (if recurring, the 12
months’ charges apply) for the Machine that is the subject of the claim or which
otherwise gives rise to the claim.
Applicability of suppliers and resellers (unchanged).
The following paragraph is added at the end of this Section:
IBM’s entire liability and your sole remedy, whether in contract or in tort, in respect of
any default shall be limited to damages.
ITALY: Limitation of Liability: The following replaces the second sentence in the first
paragraph:
In each such instance unless otherwise provided by mandatory law, IBM is liable for
no more than: (item 1 unchanged) 2)as to any other actual damage arising in all
situations involving non-performance by IBM pursuant to, or in any way related to
the subject matter of this Statement of Warranty, IBM’s liability, will be limited to the
total amount you paid for the Machine that is the subject of the claim.
Applicability of suppliers and resellers (unchanged).
The following replaces the second paragraph of this Section:
Unless otherwise provided by mandatory law, IBM and your reseller are not liable for
any of the following: (items 1 and 2 unchanged) 3) indirect damages, even if IBM or
your reseller is informed of their possibility.
SOUTH AFRICA, NAMIBIA, BOTSWANA, LESOTHO AND SWAZILAND:
Limitation of Liability: The following is added to this Section:
IBM’s entire liability to you for actual damages arising in all situations involving
nonperformance by IBM in respect of the subject matter of this Statement of Warranty
will be limited to the charge paid by you for the individual Machine that is the subject
of your claim from IBM.
Appendix A. Product warranties and notices
57
TURKIYE: Production Status: The following replaces this Section:
IBM fulfills customer orders for IBM Machines as newly manufactured in accordance
with IBM’s production standards.
UNITED KINGDOM: Limitation of Liability: The following replaces items 1 and 2
of the first paragraph of this Section:
1. death or personal injury or physical damage to your real property solely caused by
IBM’s negligence; 2. the amount of any other actual direct damages or loss, up to the
greater of Pounds Sterling 150,000 or 125 percent of the charges (if recurring, the 12
months’ charges apply) for the Machine that is the subject of the claim or which
otherwise gives rise to the claim.
The following item is added to this paragraph:
3. breach of IBM’s obligations implied by Section 12 of the Sale of Goods Act 1979 or
Section 2 of the Supply of Goods and Services Act 1982.
Applicability of suppliers and resellers (unchanged).
The following is added to the end of this Section:
IBM’s entire liability and your sole remedy, whether in contract or in tort, in respect of
any default will be limited to damages.
NORTH AMERICA
CANADA: Warranty Service: The following is added to this section:
To obtain warranty service from IBM, call 1-800-565-3344. In Toronto, call 416-3833344.
UNITED STATES OF AMERICA: Warranty Service: The following is added to this
section:
To obtain warranty service from IBM, call 1-800-772-2227.
Notices
This section contains trademarks, electronic emission notices, and other important
information.
This publication was developed for products and services offered in the U.S.A.
IBM may not offer the products, services, or features discussed in this document in
other countries. Consult your local IBM representative for information on the
products and services currently available in your area. Any reference to an IBM
product, program, or service is not intended to state or imply that only that IBM
product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any IBM intellectual property right may be
used instead. However, it is the user’s responsibility to evaluate and verify the
operation of any non-IBM product, program, or service.
IBM may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you any
license to these patents. You can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
58
IBM® xSeries 220: Installation Guide
Edition notice
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements
and/or changes in the product(s) and/or the program(s) described in this publication
at any time without notice.
Any references in this publication to non-IBM Web sites are provided for convenience
only and do not in any manner serve as an endorsement of those Web sites. The
materials at those Web sites are not part of the materials for this IBM product, and use
of those Web sites is at your own risk.
IBM may use or distribute any of the information you supply in any way it believes
appropriate without incurring any obligation to you.
© COPYRIGHT INTERNATIONAL BUSINESS MACHINES CORPORATION,
2000. All rights reserved.
Note to U.S. Government Users - Documentation related to restricted rights - Use,
duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule
Contract with IBM Corp.
Processing date data
This IBM hardware product and IBM software products that might be packaged with
it have been designed, when used in accordance with their associated documentation,
to process date data correctly within and between the 20th and 21st centuries,
provided all other products (for example, software, hardware, and firmware) used
with these products properly exchange accurate date data with them.
IBM cannot take responsibility for the date data processing capabilities of non-IBM
products, even if those products are preinstalled or otherwise distributed by IBM.
You should contact the vendors responsible for those products directly to determine
the capabilities of their products and update them if needed. This IBM hardware
product cannot prevent errors that might occur if software, upgrades, or peripheral
devices you use or exchange data with do not process date data correctly.
The foregoing is a Year 2000 Readiness Disclosure.
Appendix A. Product warranties and notices
59
Trademarks
The following terms are trademarks of the IBM Corporation in the United States,
other countries, or both:
ServeRAID
EtherJet
ServerGuide
HelpCenter
ServerProven
IBM
Update Connector
Netfinity
Wake on LAN
Predictive Failure Analysis
xSeries
Intel, MMX, LANDesk, Pentium, Pentium II Xeon, and Pentium III Xeon are
trademarks or registered trademarks of Intel Corporation in the United States, other
countries, or both.
Microsoft, Windows, and Windows NT are trademarks or registered trademarks of
Microsoft Corporation.
Other company, product, and service names may be trademarks or service marks of
others.
Important notes
Processor speeds indicate the internal clock speed of the microprocessor; other factors
also affect application performance.
When referring to hard disk drive capacity, MB stands for 1000000 bytes and GB
stands for 1000000000 bytes. Total user-accessible capacity may vary depending on
operating environments.
Maximum internal hard disk drive capacities assume the replacement of any standard
hard disk drives and population of all hard disk drive bays with the largest currently
supported drives available from IBM.
Unless otherwise stated, IBM makes no representations or warranties with respect to
non-IBM products. Support (if any) for the non-IBM products is provided by the third
party, not IBM.
Some software may differ from its retail version (if available), and may not include
user manuals or all program functionality.
Electronic emission notices
Federal Communications Commission (FCC)
Statement
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
60
IBM® xSeries 220: Installation Guide
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Properly shielded and grounded cables and connectors must be used in order to meet
FCC emission limits. IBM is not responsible for any radio or television interference
caused by using other than recommended cables and connectors or by unauthorized
changes or modifications to this equipment. Unauthorized changes or modifications
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Industry Canada Class A emission compliance
statement
This Class A digital apparatus complies with Canadian ICES-003.
Avis de conformité à la réglementation d'Industrie Canada
Cet appareil numérique de classe A est conforme à la norme NMB-003 du Canada.
Australia and New Zealand Class A statement
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
United Kingdom telecommunications safety
requirement
Notice to Customers
This apparatus is approved under approval number NS/G/1234/J/100003 for
indirect connection to public telecommunication systems in the United Kingdom.
European Union EMC Directive conformance statement
This product is in conformity with the protection requirements of EU Council
Directive 89/336/EEC on the approximation of the laws of the Member States relating
to electromagnetic compatibility. IBM cannot accept responsibility for any failure to
satisfy the protection requirements resulting from a nonrecommended modification of
the product, including the fitting of non-IBM option cards.
This product has been tested and found to comply with the limits for Class A
Information Technology Equipment according to CISPR 22/European Standard EN
55022. The Limits for Class A equipment were derived for commercial and industrial
environments to provide reasonable protection against interference with licensed
communication equipment.
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
Appendix A. Product warranties and notices
61
Taiwan electrical emission statement
Japanese Voluntary Control Council for Interference
(VCCI) statement
Power cords
For your safety, IBM provides a power cord with a grounded attachment plug to use
with this IBM product. To avoid electrical shock, always use the power cord and plug
with a properly grounded outlet.
IBM power cords used in the United States and Canada are listed by Underwriter’s
Laboratories (UL) and certified by the Canadian Standards Association (CSA).
For units intended to be operated at 115 volts: Use a UL-listed and CSA-certified cord
set consisting of a minimum 18 AWG, Type SVT or SJT, three-conductor cord, a
maximum of 15 feet in length and a parallel blade, grounding-type attachment plug
rated 15 amperes, 125 volts.
For units intended to be operated at 230 volts (U.S. use): Use a UL-listed and CSAcertified cord set consisting of a minimum 18 AWG, Type SVT or SJT, three-conductor
cord, a maximum of 15 feet in length and a tandem blade, grounding-type attachment
plug rated 15 amperes, 250 volts.
For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a
grounding-type attachment plug. The cord set should have the appropriate safety
approvals for the country in which the equipment will be installed.
IBM power cords for a specific country or region are usually available only in that
country or region.
62
IBM® xSeries 220: Installation Guide
IBM power cord part
number
Used in these countries and regions
13F9940
Argentina, Australia, China (PRC), New Zealand, Papua New
Guinea, Paraguay, Uruguay, Western Samoa
13F9979
Afghanistan, Algeria, Andorra, Angola, Austria, Belgium, Benin,
Bulgaria, Burkina Faso, Burundi, Cameroon, Central African Rep.,
Chad, China (Macau S.A.R.), Czech Republic, Egypt, Finland,
France, French Guiana, Germany, Greece, Guinea, Hungary,
Iceland, Indonesia, Iran, Ivory Coast, Jordan, Lebanon,
Luxembourg, Malagasy, Mali, Martinique, Mauritania, Mauritius,
Monaco, Morocco, Mozambique, Netherlands, New Caledonia,
Niger, Norway, Poland, Portugal, Romania, Senegal, Slovakia,
Spain, Sudan, Sweden, Syria, Togo, Tunisia, Turkey, former USSR,
Vietnam, former Yugoslavia, Zaire, Zimbabwe
13F9997
Denmark
14F0015
Bangladesh, Burma, Pakistan, South Africa, Sri Lanka
14F0033
Antigua, Bahrain, Brunei, Channel Islands, China (Hong Kong
S.A.R.), Cyprus, Dubai, Fiji, Ghana, India, Iraq, Ireland, Kenya,
Kuwait, Malawi, Malaysia, Malta, Nepal, Nigeria, Polynesia, Qatar,
Sierra Leone, Singapore, Tanzania, Uganda, United Kingdom,
Yemen, Zambia
14F0051
Liechtenstein, Switzerland
14F0069
Chile, Ethiopia, Italy, Libya, Somalia
14F0087
Israel
1838574
Thailand
6952301
Bahamas, Barbados, Bermuda, Bolivia, Brazil, Canada, Cayman
Islands, Colombia, Costa Rica, Dominican Republic, Ecuador, El
Salvador, Guatemala, Guyana, Haiti, Honduras, Jamaica, Japan,
Korea (South), Liberia, Mexico, Netherlands Antilles, Nicaragua,
Panama, Peru, Philippines, Saudi Arabia, Suriname, Taiwan,
Trinidad (West Indies), United States of America, Venezuela
Appendix A. Product warranties and notices
63
64
IBM® xSeries 220: Installation Guide
Index
Numerics
933 MHz microprocessor
installing 29
A
acoustical noise emmisions 2
activity lights
CD-ROM drive 37
diskette drive 37
hard disk drive 23, 37
SCSI 23, 37
adapter
considerations 13
Ethernet 13
installing 13, 14
optional system-management
13
PCI 12
PCI bus 13
RAID 15, 22, 25
air baffle
removing 10
air circulation 21
B
bay
drive 18
EMC shield 20
filler panel 20
bays 1, 2, 3, and 4 20
bays 5, 6, and 7 23, 25
boot
microprocessor 26
boot block jumper 6
bus
PCI 13
C
controls and indicators 37
cooling 9
cover
installing 31
removing 10
FCC Class A notice 60
features 2
filler panel 20
D
hard disk drive
activity light 23, 37
installing 20, 23, 25
specifications 2
status light 23
heat output 2
heat sink
installing 28
removing 30
height 2
hot-swap drive
backplane 24
installing 19, 25
depth 2
DIMM
installation sequence 16
installing 17
retaining clips 17
DIMM connector
locations 17
DIMM See memory module 16
diskette
eject button 37
diskette drive
activity light 37
installing 20
specifications 2
documentation CD 1
drive
bay filler panel 20
bay locations 18
cage 23
hot-swap
installation sequence 24
installing 25
non-hot-swap 23
preinstallation 19
standard 2
E
eject button
CD-ROM 37
diskette 37
electrical input 2
electronic emission Class A notice
60
cable-management arm 33
cabling
external 32
rack model 33
RAID adapter 15
routing on back 32
SCSI device 21, 23
CD-ROM drive
activity light 37
eject button 37
installing 20
specifications 2
Class A electronic emission notice
60
colors, meaning of 3
components
color 3
location of 3
major 3
configuration
hardware, cabling for 32
Configuration/Setup Utility program 39
configuring your server 39
connectors, external 32
© Copyright IBM Corp. 2000
electrostatic discharge-sensitive devices, handling xi, 14, 17
EMC shield 20
environment
air temperature 2
humidity 2
Ethernet adapter slot 13
expansion bays
location 18
specifications 2
type 18
expansion slot cover 14
expansion slots
location 12
specifications 2
type 12
external
cabling 32
port connectors 5
F
fan sink
installing 29
removing 30
H
I
I/O ports 32
important notes 60
installation sequence
DIMMs 16
hot-swap drives 24
installing
adapter 14
fan sink 29
hard disk drive 19
heat sink 28
memory module 16
microprocessor 29
side cover 31
VRM 29
installing options 9
integrated functions 2
internal cable connectors 5
J
J41 connector 15
jumper blocks 6
jumpers and switches 6
L
LEDs
CD-ROM drive activity 37
diskette drive activity 37
front of server 37
hard disk drive activity 23, 37
hard disk drive status 23
power-on 37
SCSI activity 23, 37
system error 37
lights See LEDs 37
logs
error 41
event 41
M
major components 3
memory
65
configuration changes 16
specifications 2
memory module
installing 16
order of installation 16
specifications 2
supported 16
microprocessor
fan sink 29, 30
heat sink 28, 30
installing 26, 29
removing 30
specifications 2
startup 26
VRM 26, 29
microswitches 6
S
V
safety information
book v
electrical vii
laser viii
lifting ix
SCSI
activity light 23, 37
adapter boot option 13
cable, rerouting for ServeRAID
adapter 15
device 21
SCSISelect Utility program 39
ServeRAID adapter 15
ServeRAID Configuration program
video controller
disabling 12
specifications 2
voltage regulator module
installing 26, 29
removing 30
VRM See voltage regulator module
26, 29
N
ServerGuide CDs 39
shield
power-control button 35
shutting down the server 36
side cover
installing 31
removing 10
size, server 2
slots See expansion slots 4, 12
specifications 2
starting the server 35
static-sensitive devices, handling xi
status lights 37
stopping the server 36
support bracket
removing 10
switch block 6
switch functions 7
switches and jumpers 6
system board
connectors
internal cables 5
options 4
external port connectors 5
jumper blocks 6
switch block 6
switches and jumpers 6
system reliability 9
system-management adapter 13
39
non-hot-swap drives
installing 19
NOS See operating system 39
O
operating system, installing 39
operator information lights 37
optional
system-management
adapter 13
P
PCI
adapters 12
bus A 13
bus B 13
Ethernet adapter slot 13
expansion slots 12
system-management adapter
slot 13
population order
DIMMs 16
hot-swap drives 24
power cords 62
power supply
specifications 2
power-control button 37
power-control button shield 35
power-on light 37
problem solving 41
PXE Boot Agent Utility 39
R
RAID See adapter 15, 22, 25
reliability, system 9
removable-media drives
installing 20
removing
air baffle 10
fan sink 30
heat sink 30
microprocessor 30
side cover 10
support bracket 10
VRM 11, 30
retainer
adapter 15
retaining clips
DIMM 17
66
IBM® xSeries 220: Installation Guide
T
tape drive
installing 20
temperature
air 2
terminator card
microprocessor 26, 29
thermal material 28, 29
trademarks 60
troubleshooting 41, 45
turning off the server 36
turning on the server 35
U
U11
U12
connector 26
connector 26
United States electronic emission
Class A notice 60
United States FCC Class A notice 60
W
Wake on LAN adapter slot 13
weight 2
width 2
IBM
Part Number: 06P4598
Printed in the United States of America.
6P4598
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement