M962544-YYY0A | M962457-YYY0A | M952430-0070A | M913207-0070A | M922872-0070A | M962458-0070A | A919661-0020A | M964395-0070A | 7038.101.002 | 2064101P.YYY | M962090-0070A | A911836-0070A | M962430-0070A | American Standard 7038.101, M964370-YYY0A, M964368-0070A, M964369-YYY0A, M907315-YYY0A, M918511-0070A, M951483-0070A, M950269-YYY0A, A917514-0070A, M917136-0070A, M922882-0070A, M922380-0070A, M952425-YYY0A, M964371-YYY0A Installation instructions

Installation

Instructions

TROPIC™

7038.101

MONOBLOCK LAVATORY

FAUCET with Speed Connect™ Drain

Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on

American Standard faucets.

Speed Connect™ Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the first time, every time.

Certified to comply with ANSI A112.18.1

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

M965446 REV. 1.3

Recommended tools

Screwdriver Channel Locks Adjustable Wrench

1

INSTALL FAUCET CAUTION

Installation with ESCUTCHEON PLATE: Seat SEAL (1) into groove in FAUCET BASE (2).

Fig. A. Apply a light bead of plumbers putty to underside of ESCUTCHEON (3) if mounting surface is uneven.

Place ESCUTCHEON (3) onto sink or mounting surface. Fig. A. Feed FAUCET SUPPLIES (4), MOUNTING STUD (5), DRAIN CABLE

ASSEMBLY (6) and SPRAY HOSE (10, 10a) through ESCUTCHEON with PUTTY

PLATE (3) and mounting hole of lavatory or mounting surface. Fig. A.

Installation less ESCUTCHEON: Seat SEAL (1) into groove in

FAUCET BASE (2). Fig. B.

Fig. B. Feed FAUCET SUPPLIES (4), MOUNTING

STUD (5), DRAIN CABLE ASSEMBLY (6) and

SPRAY HOSE (10, 10a) through mounting hole of lavatory or mounting surface.

Fig.

A.

Fig. A & B. From below, push GASKET (7) with RETAINING WASHER (8) onto

MOUNTING STUD (5). Install MOUNTING

NUT (9) onto MOUNTING STUD (5). Fig. B.

2

GROOVE

(FAUCET

BASE)

MOUNTING

SURFACE

Adjust Faucet so that it is centered.

Tighten MOUNTING NUT (9) to complete faucet mounting. Fig. A & B.

2

GROOVE

(FAUCET

BASE)

MOUNTING

SURFACE

5

4

1

7, 8

9

3

Fig.

B.

5

6

7, 8

9

10a

10

6

4

1

PUTTY

IF REQUIRED

10a

10

1

2

POP-UP DRAIN

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under

DRAIN POP-UP (3).

Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig.

B.

Fig.

A.

1

3

2

3

REMOVE FLANGE

Thread FLANGE (1) counter-clockwise and remove

FLANGE (1) and FOAM GASKET (2) from drain body. Fig.

A.

Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against

LOCKNUT (3). Fig.

B.

Fig.

A.

1

2

4

3

Fig.

B.

Fig.

B.

DRAIN

BODY

4

4

INSTALL DRAIN FROM

BELOW FIXTURE

From under side of SINK install DRAIN BODY (1) up through drain outlet.

Note: No plumber’s putty or caulk is required.

The CABLE ATTACHMENT

POINT (2) must face towards the rear of the SINK.

Install FOAM GASKET (3) and

FLANGE (4) onto drain body from above SINK and tighten

FLANGE (4) firmly.

4

3

REAR OF SINK

DRAIN

OUTLET

1

2

5

TIGHTEN LOCKNUT

Tighten LOCKNUT (1) firmly with Adjustable

Wrench or Channel Locks.

6

FLANGE GASKET AND POP-UP KNOB

Check DRAIN FLANGE in SINK to ensure that

WHITE FOAM GASKET (3) is fully compressed and not visible. Fig. A.

POP-UP KNOB (1) must be fully down. Fig. B.

Fig.

A.

WHITE FOAM

GASKET

NOT VISIBLE

DRAIN

FLANGE

Fig.

B. DOWN

1

1

M965446 REV. 1.3

2

7

ATTACH CABLE CONNECTOR

Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A.

Your new POP-UP DRAIN installation is now complete. Fig. B.

Note: Tailpeice on pop-up drain is 1-1/4” O.D.

Fig.

B.

Fig.

A.

1

Fig.

B.

2

1-1/4” O.D.

8

CHECK OPERATION OF POP-UP

Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.

Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.

1

2

9

MAKE WATER SUPPLY and SPRAY HOSE CONNECTIONS

Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.

Connection on fitting supplies are 3/8" compression. Connect left SUPPLY (1) to Hot (Marked with a Red Band) and right supply to COLD (2) wall supply.

Faucet supplies are 20" long from faucet base.

Note: If additional supply length is required, installer must purchase additional parts separately.

Important: If SUPPLY HOSES (1, 2) are to long, loop as illustrated to avoid kinking.

From under mounting surface connnect FLEXIBLE INLET

TUBE (3) to HOSE END (4) and tighten with wrenches.

Install the WEIGHT (5) onto HOSE (6) 2 inches above the loop on the side of the pull-out hose. Rotate the WEIGHT

HALVES (5) together and secure with SCREW (7).

Connect 1-1/4" O.D. tailpiece on POP-UP DRAIN to waste outlet.

1

RED

BAND

HOT

7

2" ABOVE LOOP

6

3

3

4

2

BLUE

BAND

3/8" COMPRESSION

COLD

5

M965446 REV. 1.3

10

TEST INSTALLED FITTING

With HANDLE (1) in OFF position, turn on WATER

SUPPLIES (2) and check all connections for leaks.

Remove AERATOR (3) with KEY (6) provided.

Operate HANDLE (1) to flush water lines thoroughly.

Replace AERATOR (3).

CHECK DRAIN CONNECTIONS

Operate POP-UP KNOB (4) and fill lavatory with water.

Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.

Release POP-UP KNOB (4) down and check all drain connections and "P" trap for leaks. Tighten if necessary.

4

WASTE

OUTLET

1

ON

HOT

OFF

COLD

5

3

6

11

SERVICE CAUTION Turn off hot and cold water supplies before beginning.

To remove or replace cartridge:

Turn valve to OFF position.

Pull out INDEX (1).

Loosen SET SCREW (2). Pull off HANDLE (3).

Pull off CAP (4).

Remove CARTRIDGE SCREWS (5).

Pull out CARTRIDGE (6).

Inspect CARTRIDGE (6) and O-RING (7) for debris and clean if necessary.

3

Clean MANIFOLD (8) and rinse clean.

Reinstall CARTRIDGE (6) and O-RING (7) onto MANIFOLD (8).

Reinstall CARTRIDGE SCREWS (5), CAP (4) and HANDLE ASSEMBLY (3).

If spout drips, operate handle several times from OFF to ON and HOT to

COLD position. Do not force.

To lock spout into place

Unscrew the SET SCREW (9) from underneath the spout and replace with the SCREW (10) in the plastic bag provided while spout is in place.

Switch SCREWS again to allow spout to pull out.

2

8

“P” TRAP

2

2

4

1

2.5mm HEX KEY

5

6

7

9

10

12

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

M965446 REV. 1.3

4

Speed Connect™ Drain

Troubleshooting Guide

If sink does not hold water even though Stopper is in the “down” position:

• Follow CABLE ADJUSTMENT PROCEDURE.

If Stopper does not raise up fully or sink drains too slowly:

• Follow CABLE ADJUSTMENT PROCEDURE.

If you need to remove the Stopper:

• Follow STOPPER REMOVAL PROCEDURE.

If you would like the ability to remove your Stopper simply by lifting it out of the drain:

• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.

CABLE ADJUSTMENT PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as

“Cam” in the illustration. Fig. B.

Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the

Stopper should be in the UP position. Fig. B, C.

Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.

Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the

Drain Body Connection (2) and hand-tighten. Fig. A.

Fig.

A. Fig.

B. Fig.

C. DOWN

CAM 1

RE-ATTACH

CAM CAP STOPPER

LIFT-KNOB

DISCONNECT

2

STOPPER REMOVAL PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B.

Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.

Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.

The Stopper can now be removed by lifting it out of the Drain. Fig. F.

Fig.

D. Fig.

E.

REMOVE

CAM

Fig.

F.

REMOVE

CAM CAP

M965446 REV. 1.3

5

STOPPER INSTALLATION PROCEDURE

The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable).

Locked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G.

To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the

Sink and the American Standard logo is facing front. Rotate

Stopper slightly if necessary so that the Stopper slides all the way down.Fig. G.

Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J.

Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig. K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

Troubling Shooting Guide to complete installation. Stopper will be in “Locked” mode and not be removable.

LOGO

LOOP TOWARD

REAR OF SINK

DRAIN

Locked Mode

(Vandal Proof)

Fig.

G.

Unlocked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. H.

To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the

Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.

Fig.

H.

Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J.

Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig. K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

“Troublingshooting Guide” to complete installation. Stopper will be in “Unlocked” mode and removable.

LOGO

Fig.

180˚

LOOP TOWARD

FRONT OF SINK

DRAIN

Unlocked Mode

H.

Fig.

J. Fig.

K.

INSTALL

CAM CAP

M965446 REV. 1.3

6

M964368-0070A

BUTTON/SCREW KIT

(RED/BLUE)

M964369-YYY0A

BUTTON/SCREW KIT

M950269-YYY0A

SPRAY HOSE

ASSEMBLY

A917514-0070A

SET SCREW

(UNFIXED SPOUT)

M917136-0070A

SET SCREW

(FIXED SPOUT)

M922882-0070A

AERATOR

M922380-0070A

AERATOR KEY

M962090-0070A

MOUNTING KIT

M965446 REV. 1.3

M964370-YYY0A

HANDLE KIT

TROPIC™

MONOBLOCK LAVATORY

FAUCET with Speed Connect™ Drain

MODEL NUMBER

7038.101

M907315-YYY0A

COVER

M918511-0070A

CARTRIDGE SCREWS

M951483-0070A

CARTRIDGE

Replace the "YYY" with appropriate finish code

CHROME

SATIN NICKEL

002

295

M964371-YYY0A

POP-UP ROD ASSEMBLY

A911836-0070A

SEAL

2064101P.YYY

ESCUTCHEON AND

PUTTY PLATE

M952425-YYY0A

DRAIN ASSEMBLY

M962544-YYY0A

STOPPER

ASSEMBLY

M952430-0070A

CABLE ASSEMBLY

M962457-YYY0A

FLANGE

ASSEMBLY

M922872-0070A

CAM SEAT INSERT

M962430-0070A

CAM ASSEMBLY

M913207-0070A

TAILPIECE INSERT

M964395-0070A

WEIGHT KIT

A919661-0020A

TAILPIECE

M962458-0070A

DRAIN MOUNTING KIT

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1-800 442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-1200

Product names listed herein are trademarks of American Standard Inc.

© AS America, Inc. 2013

7

8