Sharp ER-A420 Instruction manual

Sharp ER-A420 Instruction manual
ER-A410/A420
ELECTRONIC CASH REGISTER
MODEL
ER-A410
ER-A420
INSTRUCTION MANUAL
The above illustration shows the model ER-A410.
N
HYO-1,4(SEC)
1
03.12.18, 6:20 PM
ER-A410/A420(SEC)HYO-2-3
03.11.4 8:19 AM
Page 2
WARNING
FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void
the user's authority to operate this equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
own expense.
CAUTION
The AC outlet shall be installed near the equipment and shall be easily
accessible.
FOR YOUR RECORDS
Please record below the model number and serial number, for easy
reference, in case of loss or theft. These numbers are located on the
right side of the unit. Space is provided for further pertinent data.
Model Number
Serial Number
Date of Purchase
Place of Purchase
ER-A410/A420(SEC)-1
03.12.22 0:12 PM
Page 1
INTRODUCTION
Thank you very much for your purchase of the SHARP Electronic Cash Register, Model ER-A410/A420.
Please read this manual carefully before operating your machine to gain a thorough understanding of the
functions and features offered by this model ECR.
Please keep this manual for future reference, it may help you if you encounter operational problems.
IMPORTANT
• Install your register in a location that is not subject to direct radiation, unusual temperature changes,
high humidity or exposed to water sources.
Installation in such locations could cause damage to the cabinet and the electrical components.
• The register should not be operated by an individual with wet hands.
The water could seep into the interior of the register and cause component failure.
• When cleaning your register, use a dry, soft cloth. Never use solvents, such as benzine and/or thinner.
The use of such chemicals will lead to discoloration or deterioration of the cabinet.
• The register plugs into any standard wall outlet (120V ±10% AC) which utilizes a dedicated ground
circuit.
Please note that other electrical devices on the same electrical circuit could cause the register to malfunction.
• If the register malfunctions, call your local dealer for service - do not try to repair the register yourself.
• For a complete electrical disconnection, the AC power cord must be removed from the wall outlet.
• Never disconnect the peripheral while the register remains plugged into the AC outlet.
PRECAUTION
This Electronic Cash Register has a built-in memory protection circuit which is supported by rechargeable
batteries.
It is important to know that all batteries will, in time, dissipate their charge even if not used. Therefore to insure
an adequate charge in the protection circuit, and to prevent any possible loss of memory during or after
installation, it is recommended that each unit be allowed to recharge for a period of 24 to 48 hours prior to and
during use by the customer.
In order to charge the batteries, the machine must be plugged in. This recharging precaution can prevent
unnecessary equipment malfunctions or service calls.
1
ER-A410/A420(SEC)-1
03.12.22 0:12 PM
Page 2
CONTENTS
INTRODUCTION ····················································································································································1
IMPORTANT ··························································································································································1
PRECAUTION························································································································································1
CONTENTS····························································································································································2
EXTERNAL VIEW OF THE ER-A410 ····················································································································7
Front view ···············································································································································7
Rear view················································································································································7
EXTERNAL VIEW OF THE ER-A420 ····················································································································8
Front view ···············································································································································8
Rear view················································································································································8
PRINTER································································································································································9
KEYBOARD ·························································································································································10
1 ER-A410 standard keyboard layout·········································································································10
2 ER-A420 standard keyboard layout·········································································································12
3 Standard key number layout····················································································································13
4 Installing the keyboard sheet (ER-A420) ·································································································14
KEYS AND SWITCHES ·······································································································································15
1 Mode switch and mode keys ···················································································································15
2 Drawer lock key ·······································································································································15
3 Cashier code entry key ····························································································································16
4 Receipt ON/OFF function ························································································································16
DISPLAYS ···························································································································································17
1 Operator display ······································································································································17
2 Customer display (Pop-up type) ··············································································································17
FOR THE OPERATOR
PRIOR TO ENTRIES ···········································································································································18
1 Preparations for entries ···························································································································18
2 Power saving mode ·································································································································19
3 Error warning ···········································································································································19
ENTRIES ······························································································································································20
1 Item entries ··············································································································································20
Single item entries ································································································································20
Repeat entries ······································································································································21
Multiplication entries ·····························································································································22
Successive multiplication entries··········································································································23
Split-pricing entries ·······························································································································24
Single item cash sale (SICS)/single item finalize (SIF) entries·····························································25
Scale entries·········································································································································26
PLU level shift (for direct PLU) ·············································································································28
PLU/UPC price level shift ·····················································································································30
Set PLU entries ····································································································································31
Link PLU/UPC entries···························································································································32
Age verification (Birthday entry) ···········································································································32
Mix-and-match entries ··························································································································33
Price inquiry (view) function (for PLU/UPC) ·························································································33
UPC learning function···························································································································34
Price change function (for UPCs) ·········································································································35
2 Displaying and printing subtotals ·············································································································37
Merchandise subtotal ···························································································································37
Taxable subtotal ···································································································································37
Including-tax subtotal (full subtotal) ······································································································37
2
ER-A410/A420(SEC)-1
03.12.22 0:12 PM
Page 3
Food stamp-eligible subtotal·················································································································37
Tray subtotal·········································································································································37
3 Finalization of transaction ························································································································38
Cash or Check tendering······················································································································38
Mixed tendering (check + cash)············································································································38
Cash or Check sale that does not need any tender entry ····································································39
Charge (credit) sale ······························································································································39
Mixed-tender sale (cash or check tendering + charge tendering) ························································39
4 Food stamp calculations ··························································································································40
Food stamp tendering···························································································································40
Food stamp status shift ························································································································41
5 Tax calculations ·······································································································································42
Automatic tax········································································································································42
Manual tax ············································································································································42
Automatic-tax delete·····························································································································43
Tax status shift ·····································································································································44
6 Guest check (PBLU) ································································································································45
New charge accounts ···························································································································45
Additional item entries ··························································································································46
Settlement ············································································································································46
Deposit entries······································································································································47
7 Auxiliary entries ·······································································································································48
Percent calculations (premium or discount) ·························································································48
Discount entries····································································································································49
Refund entries ······································································································································50
Refund sales mode·······························································································································50
Printing of non-add code numbers ·······································································································50
8 Payment treatment ··································································································································51
Currency conversion·····························································································································51
Received on account entries ················································································································52
Paid out entries·····································································································································52
No sale (exchange) ······························································································································52
Cashing a Check ··································································································································53
Bottle return ··········································································································································53
9 Automatic sequencing key (` key) entries····························································································53
CORRECTION ·····················································································································································54
1 Correction of the last entry (direct void)···································································································54
2 Correction of the next-to-last or earlier entries (indirect void)··································································54
3 Subtotal void ············································································································································55
4 Correction of incorrect entries not handled by the direct or indirect void function ···································55
CORRECTION AFTER FINALIZING A TRANSACTION (AFTER GENERATING A RECEIPT)························56
OVERRIDE ENTRIES ··········································································································································57
OVERLAPPED CASHIER ENTRY ······················································································································58
SPECIAL PRINTING FUNCTIONS······················································································································59
1 Copy receipt printing································································································································59
2 Validation printing function (Slip printer) ··································································································60
3 Printing of the employee’s arrival and departure times (Slip printer) ·······················································60
4 Printing of header and footer graphic logos·····························································································60
5 Remote printer send function ··················································································································61
TIME DISPLAY AND AUTOMATIC UPDATING OF THE DATE ········································································62
1 Time display ············································································································································62
2 Automatic updating of the date ················································································································62
FOR THE MANAGER
PRIOR TO PROGRAMMING ·······························································································································63
1 Programming keyboard layout·················································································································63
3
ER-A410/A420(SEC)-1
03.12.22 0:12 PM
Page 4
2 How to program alphanumeric characters·······························································································64
Using character keys on the keyboard ·································································································64
Entering character codes······················································································································64
PROGRAMMING ·················································································································································66
Basic instructions··································································································································66
Preparations for programming··············································································································66
Direct Programming ···········································································································································66
1 Setting the date and time·························································································································66
Date ······················································································································································66
Time······················································································································································67
2 Programming for departments ·················································································································67
Unit price ··············································································································································67
Functional selection······························································································································68
3 PLU/UPC programming ···························································································································70
Unit price ··············································································································································70
Functional selection······························································································································70
PLU/UPC assignment to departments··································································································72
4 Programming for discount keys (-) ······································································································72
Discount amount ··································································································································72
High amount lockout (HALO), sign (+/–), vendor/store coupon selection, food stamp status,
and tax status ·······································································································································73
5 Programming for percent keys (%)········································································································74
Percent rate ··········································································································································74
Sign (+/–), %item/%subtotal selection, food stamp status, and tax status ···········································74
6 Programming for conversion keys (ç) ··································································································75
Currency conversion rate ·····················································································································75
7 Programming for the r, p, and † keys ···························································································76
High amount lockout (HALO)················································································································76
8 Programming for the a, Å, ', and k keys ····················································································76
High amount lockout (HALO) and function selection············································································76
9 Programming for the automatic tax calculation function ··········································································78
The tax table (applicable to the add-on tax) ·························································································78
Job-Code-Based Programming ························································································································81
1 Setting the date and time·························································································································81
Setting the date (#2610) ·······················································································································81
Setting the time (#2611) ·······················································································································81
2 Setting the register and consecutive numbers ························································································82
Setting the register number (#2612)·····································································································82
Setting the consecutive number (#2613)······························································································82
3 Programming for the automatic tax calculation function ··········································································83
The tax table (#2710) ···························································································································83
The tax rate (#2711) ·····························································································································85
Doughnut tax exempt (for the Canadian tax system) (#2715)······························································86
4 Programming for departments ·················································································································87
Functional programming 1 (#2110) ······································································································87
Functional programming 2 (#2111) ······································································································89
A limit amount (HALO) of entry (#2112) ·······························································································90
Alphanumeric characters (#2114) ········································································································90
Unit price (#1110) ·································································································································91
Commission group assignment (#2115)·······························································································91
Group number (#2116) ·························································································································92
Age limitation (#2180)···························································································································92
Print station assignment (#2118)··········································································································93
Department key positioning (#2119)·····································································································93
5 PLU/UPC programming ···························································································································94
Department assignment (#1200, 2230) ································································································95
Unit prices (#1210) ·······························································································································96
4
ER-A410/A420(SEC)-1
6
7
8
9
10
03.12.22 0:13 PM
Page 5
Base quantity (#1211) ··························································································································96
Type of unit price entry, delete method, tare table no. and scale entry (#2210, 2231) ························97
Sign (+/–), food stamp status, and tax status (#2211, 2232)································································98
Alphanumeric characters (#2214) ········································································································99
Assigning of PLUs/UPCs to commission groups (#2215, 2235) ························································100
Age limitation (#2280, 2236)···············································································································101
Stock quantity (#1222, 1220, 1221)····································································································102
Set PLU (#2221)·································································································································103
Mix-and-match table (#2217, 2225)····································································································104
Print station to PLU/UPC assignment (#2218) ···················································································105
Delete period for non-accessed UPC code (#2029)···········································································105
Programming Non-PLU code format (#2025)·····················································································106
Link PLU/UPC link (#2220)·················································································································107
Programming of PLU levels and direct PLU keys (#2219) ·································································107
Programming for miscellaneous keys····································································································108
Programming the rate (%, ç, commission) and the discount (-) (#1310) ··································108
Currency description text programming (ç) (#2334) ·······································································109
A limit amount (HALO) of entry (-, †, r, p) (#2312) ······························································110
+/– sign, food stamp status and tax status (%, -) (#2311)····························································110
Percent entry type (%) (#2310) ········································································································112
Item % or subtotal % selection (%) (#2315) ·····················································································112
Percent rate limitation (%) (#2313)···································································································113
Vendor or store coupon selection (-) (#2316)·················································································113
Programming for the a, Å, k, CHK2 , and ' through , keys ······················································114
Functional programming (#2320) ·······································································································114
Tax delete (#2326) ·····························································································································116
High amount lockout (HALO) for check cashing, check change, and cash in drawer (#2321)···········117
High amount lockout (HALO) of entry for media keys (#2322)···························································117
Print station assignment (#2328)········································································································118
Programming of function text·················································································································119
Programming (#2314)·························································································································119
List of function texts····························································································································120
Cashier programming ····························································································································122
Cashier code (#1500) ·························································································································122
Cashier name (#1514)························································································································122
Assigning cashiers to drawers (#2510) ······························································································123
Programming various functions ·············································································································123
Programming for optional feature selection (#2616) ··········································································123
Programming the parameter of the slip printer (#2615)······································································128
Setting the time limit for THE TILL TIMERTM (#2617) ·········································································128
Scale tare table (#2618) ·····················································································································129
Programming of logo messages (#2614) ···························································································130
Selection of X1/Z1 and X2/Z2 reports to be printed in the stacked report sequence (#2620)············131
Setting the time range for hourly reports (#2619)···············································································132
Programming of power saving mode (#2689) ····················································································132
PBLU code programming (#2810)······································································································133
Functional programming for the printer (#2990) ·················································································133
Programming of error messages (#2641)···························································································134
Check validation message (#2642) ····································································································135
Slip printer’s logo message (#2643) ···································································································135
RS-232C channel assignment (#2690) ······························································································136
Barcode reader programming (#2691) ·······························································································137
Remote printer programming (#2692) ································································································138
Second remote printer programming (#3653) ····················································································138
Remote printer name programming (#3654) ······················································································139
Print format for remote printer (#3655) ·······························································································139
Chit receipt format (#3656)·················································································································140
5
ER-A410/A420(SEC)-1
03.12.22 0:13 PM
Page 6
Programming of RS-232C interface (#6110, 6111, 6112, 6113, 6115, 6220) ····································141
Programming the CAT interface (#7110, 7111, 7112, 7113, 7114, 7115)··········································142
Secret codes to control access to the PGM1 mode, X1/Z1 mode and X2/Z2 mode
(#2630, 2631, 2632) ···························································································································143
Setting the AUTO key (#2900) ···········································································································144
11 TRAINING mode ···································································································································145
12 Reading stored programs ······················································································································146
Program details and procedures for their reading ··············································································146
Sample printouts·································································································································148
13 Universal Product Code (UPC) or European Article Number (EAN) ·····················································155
UPC or EAN code·······························································································································155
Add-on code ·······································································································································156
READING (X) AND RESETTING (Z) OF SALES TOTALS···············································································157
1 Summary of reading (X) and resetting (Z) reports and the key operations to obtain the reports ··········157
2 Daily sales totals····································································································································160
General report ····································································································································160
Cashier report·····································································································································163
Hourly report·······································································································································165
Full department report ·······················································································································166
Individual group total report on department························································································166
Full group total report on department ·································································································166
PLU/UPC report (by designated range or pick up list)········································································167
PLU/UPC report by associated department ·······················································································168
PLU/UPC zero sales report ················································································································168
PLU/UPC price category report ··········································································································168
PLU/UPC stock report (by designated range or pick up list) ······························································169
Commission sales report ····················································································································169
PBLU report········································································································································169
PBLU report by cashier ······················································································································170
Transaction report ······························································································································170
Cash in drawer report ·························································································································170
X1/Z1 stacked report ··························································································································170
Deleting of non-accessed UPCs·········································································································171
3 Periodic consolidation····························································································································172
General Overview·······························································································································172
Daily net report ···································································································································173
X2/Z2 stacked report ··························································································································173
COMPULSORY CASH/CHECK DECLARATION······························································································174
OPERATOR MAINTENANCE ···························································································································176
1 In case of power failure ·························································································································176
2 In case of printer error ···························································································································176
3 Thermal printing·····································································································································176
Cautions in handling the printer··········································································································176
Cautions in handling the recording paper (thermal paper) ·································································177
4 Installing and removing the paper roll····································································································178
Recording paper specifications ··········································································································178
Installing the paper roll ·······················································································································178
Removing the paper roll ·····················································································································180
Removing a paper jam ·······················································································································181
5 Cleaning the print head ·························································································································182
6 Removing the till and the drawer ···········································································································183
7 Opening the drawer by hand ·················································································································183
8 Before calling for service ·······················································································································184
Error message table ···························································································································184
LIST OF OPTIONS ············································································································································185
SPECIFICATIONS ·············································································································································186
6
ER-A410/A420(SEC)-1
03.12.22 0:13 PM
Page 7
EXTERNAL VIEW OF THE ER-A410
Front view
Customer display (Pop-up type)
Printer cover
Receipt paper
Operator display
Journal window
Keyboard
Mode switch
Drawer lock
Drawer
RS-232C connector cover (CH1)
RS-232C connector cover (CH2)
Rear view
7
ER-A410/A420(SEC)-1
03.12.22 0:13 PM
Page 8
EXTERNAL VIEW OF THE ER-A420
Front view
Customer display (Pop-up type)
Printer cover
Receipt paper
Operator display
Journal window
Keyboard
Mode switch
Drawer lock
Drawer
RS-232C connector cover (CH1)
RS-232C connector cover (CH2)
Rear view
8
ER-A410/A420(SEC)-1
03.12.22 0:13 PM
Page 9
PRINTER
The printer is a receipt/journal dual station type thermal printer, that does not require an ink ribbon or cartridge.
The average life of the printer is approximately 5 million lines.
When removing the printer cover, lift it from the rear as
shown.
When installing the printer cover, hook it on the pawls on
the cabinet and shut it.
Caution: The paper cutter is mounted on the printer
(receipt side). Be careful not to cut yourself.
Your register is shipped with the print head release lever
held in the lifted up position by a white retainer. Be sure to
remove this retainer (see the figure at the right) and push
down the print head release lever before you use the
register.
Retainer
Take-up spool
Paper roll location
Paper chute
Print head
release lever
Print head release lever
The print head can be lifted by the green lever on the right side of the printer. Pulling the lever forward, lifts the
print head up. If the paper becomes jammed and you need to move the print head farther forward, you can pull
the lever even further toward you and proceed with the removal of the jammed paper.
Note
Do not attempt to remove the paper roll with the head in the down position. This may result in
damage to the printer and print head.
9
ER-A410/A420(SEC)-1
03.12.22 0:13 PM
Page 10
KEYBOARD
1 ER-A410 standard keyboard layout
TAX
SHIFT CONV
TAX
RECEIPT JOURNAL
@
FOR
PLU/UPC
PRICE
CHANGE
INQ
NC
FS
CL
5
10
15
20
PBLU SHIFT
FINAL TEND
FS
SLIP
RA
7
8
9
4
9
14
19
RCPT
PO
4
5
6
3
8
13
18
%
1
2
3
2
7
12
17
00
1
6
11
16
VOID RFND
0
CHK
CH
MDSE
SBTL
SBTL
CA/AT/NS
All the keys but the receipt paper feed and journal paper feed keys can be re-positioned.
If you want to change the layout, please consult your dealer.
Note
RECEIPT
Receipt paper feed key
INQ
JOURNAL
Journal paper feed key
PRICE
CHANGE
CASH
0
#
PLU/UPC inquiry key
VOID
Void key
UPC price change key
RFND
Refund key
Cashier code entry key
RA
Received-on-account 1
key
Discount 1 key
PO
Paid-out 1 key
Percent 1 key
MDSE
SBTL
Merchandise subtotal
key
Numeric keys
9
%
00
TAX
Tax key
RCPT
Receipt print key
Decimal point key
TAX
SHIFT
Tax 1 shift key
NC
New charge account
balance key
Multiplication key
FS
SHIFT
Food stamp shift key
PBLU
Previous balance key
Clear key
FS
TEND
Food stamp tendered key
FINAL
Final key
CHK
Check 1 key
CONV
Conversion 1 key
(for currency conversion)
CH
Charge 1 key
SLIP
Slip print key
SBTL
Subtotal key
@
FOR
CL
1
Department keys
20
PLU/UPC
10
CASH
#
PLU/UPC key
CA/AT/NS
Cash/Amount tendered
and No-sale key
ER-A410/A420(SEC)-1
03.12.22 0:13 PM
Page 11
Optional keys
SRVC
Service key
CONV
2
%2
L1
PLU level shift 1 thru
3 keys
Conversion 2 thru 4 keys
Percent 2 thru 4 keys
%4
CONV
4
L3
CH2
PRICE
SHIFT
Charge 2 thru 5 keys
AUTO
Automatic sequencing
1 thru 5 keys
AUTO
5
Price level shift key
2
CH5
Discount 2 thru 4 keys
CHK2
Check 2 key
4
CA2
Cash total 2 key
DEPO
Deposit entry key
000
BIRTH
Birthday date entry key
DEPO
RFND
Deposit refund key
TAX2
SHIFT
DEPT
#
Department code entry
key
TRAY
SBTL
Tray subtotal key
RA2
Received-on-account
2 key
RFND
SALE
Refund sale key
PO2
Paid-out 2 key
PRINT
Validation print key
Non-add code key
REPEAT
Repeat entry key
NON
DELETE
Non delete key
SCALE
Scale key
AMT
Amount entry key
RP
SEND
Remote printer send
key
OPEN
TARE
Open tare key
#
Attention
Note
Triple zero entry key
Tax 2 thru 4 shift keys
TAX4
SHIFT
NS
No sale key
• The CA/AT/NS is a double-function key ([Cash/Amount tendered function] and [No Sale function]).
Press the CA/AT/NS key replaces the a and n key in the following descriptions for operations.
The department and direct PLU keys can be expanded, if you require expansion of the department
or direct PLU keys, please contact your dealer.
11
ER-A410/A420(SEC)-1
03.12.22 0:13 PM
Page 12
2 ER-A420 standard keyboard layout
RECEIPT JOURNAL
73
74
75
76
77
78
79
80
81
82
L1
L2
L3
AUTO CASH
#
PRICE
SHIFT RCPT
RP
SEND
PO
@
CL
%
RA
61
62
63
64
65
66
67
68
69
70
71
72
49
50
51
52
53
54
55
56
57
58
59
60
FOR
37
38
39
40
41
42
43
44
45
46
47
48
7
8
9
RFND VOID
25
26
27
28
29
30
31
32
33
34
35
36
4
5
6
CH2 SHIFT
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
CH1 CHK
1
2
3
4
5
6
7
8
9
10
11
12
0
00
MDSE
SBTL
SBTL CA/AT
Note
TAX
All the keys but the receipt paper feed and journal paper feed keys can be re-positioned.
If you want to change the keyboard layout, please consult your dealer.
RECEIPT
Receipt paper feed key
SBTL
Subtotal key
VOID
Void key
JOURNAL
Journal paper feed key
MDSE
SBTL
Merchandise subtotal key
RFND
Refund key
Cashier code entry key
RA
Received-on-account 1
key
Discount 1 key
PO
Paid-out 1 key
Receipt print key
PRICE
SHIFT
Price level shift key
Percent 1 key
AUTO
Automatic sequencing
1 key
CASH
0
#
Numeric keys
9
RCPT
00
%
Decimal point key
@
FOR
L1
1
PLU level shift 1
thru 3 keys
Multiplication key
Direct price lookup
keys
Clear key
L3
Remote printer send key
CH1
TAX
SHIFT
Tax 1 shift key
CH2
CA/AT
Cash/Amount
tendered key
CHK
Check 1 key
Non-add code key
AMT
Amount entry key
REPEAT
Repeat entry key
SCALE
Scale key
INQ
PLU/UPC inquiry key
PRICE
CHANGE
UPC price change key
NON
DELETE
Non delete key
CL
RP
SEND
82
Charge 1 and 2 keys
Optional keys
#
12
ER-A410/A420(SEC)-1
SRVC
03.12.22 0:13 PM
Service key
Page 13
SLIP
Slip print key
TAX
Tax key
CONV
4
FS
SHIFT
Food stamp shift key
CH3
FS
TEND
Food stamp tendered
key
CONV
%2
Conversion 1 thru 4 keys
Percent 2 thru 4 keys
%4
AUTO
2
Charge 3 thru 5 keys
Automatic sequencing
2 thru 5 keys
AUTO
5
2
CH5
Discount 2 thru 4 keys
CHK2
Check 2 key
4
CA2
Cash total 2 key
DEPO
Deposit entry key
000
BIRTH
Birthday date entry key
DEPO
RFND
Deposit refund key
TAX2
SHIFT
DEPT
#
Department code entry
key
TRAY
SBTL
Tray subtotal key
RA2
Received-on-account 2
key
RFND
SALE
Refund sale key
TAX4
SHIFT
PO2
Paid-out 2 key
PRINT
Validation print key
PBLU
Previous balance key
NC
New charge account
balance key
NS
OPEN
TARE
Note
No sale key
Open tare key
PLU
UPC
FINAL
Triple zero entry key
Tax 2 thru 4 shift keys
PLU/UPC key
Final key
The department and direct PLU keys can be expanded, if you require expansion of the department
or direct PLU keys, please contact your dealer.
3 Standard key number layout
These key numbers are used for positioning of department keys and direct PLU keys. Refer to pages 93 and 107.
This layout can be changed by your dealer.
For ER-A410
005
010
015
020
004
009
014
019
003
008
013
018
002
007
012
017
001
006
011
016
13
ER-A410/A420(SEC)-1
03.12.22 0:13 PM
Page 14
For ER-A420
093
094
095
096
097
098
099
100
101
102
081
082
083
084
085
086
087
088
089
090
091
092
069
070
071
072
073
074
075
076
077
078
079
080
057
058
059
060
061
062
063
064
065
066
067
068
045
046
047
048
049
050
051
052
053
054
055
056
033
034
035
036
037
038
039
040
041
042
043
044
021
022
023
024
025
026
027
028
029
030
031
032
4 Installing the keyboard sheet (ER-A420)
Insert the keyboard sheet between the keyboard cover and the cabinet as illustrated below.
➀ Turn over the keyboard cover.
➁ Insert the keyboard sheet into a slit.
Keyboard cover
Keyboard sheet
➂ Close the keyboard cover.
Note
14
• Do not spread the keyboard cover too far as it might tear the tabs.
• Replace the keyboard sheet with a new one if by chance it gets wet. Use of a wet keyboard
sheet may cause problems.
• Be sure to use only SHARP-supplied keyboard sheets. Thick or hard sheets can make key
operations difficult.
• Place the keyboard sheet evenly under the keyboard cover.
• If you require a new keyboard sheet, please contact your dealer.
• The keyboard cover will eventually wear out. If your keyboard cover is dirty or broken, replace the
cover with a new one. For details, contact your authorized SHARP dealer.
ER-A410/A420(SEC)-1
03.12.22 0:13 PM
Page 15
KEYS AND SWITCHES
1 Mode switch and mode keys
The mode switch can be operated by inserting one of the three supplied mode keys – manager (MA),
submanager (SM), and operator (OP) keys. These keys can be inserted or removed only when the switch is in
the “REG” or “OFF” position.
• Manager key (MA)
Operative range
• Submanager key (SM)
SM
MA
• Operator key (OP)
OP
The mode switch has these settings:
OFF:
This mode locks all register operation.
No change occurs to register data.
OP X/Z: This setting allows cashiers to take X or Z reports for their sales
information. It can also be used for displaying the date/time and
printing the employee’s arrival/departure times. And it can be used to toggle receipt state “ON” and
“OFF” by pressing the q key. (This setting may be used only when your register has been
programmed for “OP X/Z mode available” in the PGM2 mode.)
REG:
For entering sales
PGM1: To program those items that need to be changed often: e.g., unit prices of departments, PLUs or
UPCs, and percentages.
PGM2: To program all PGM1 programs and those items that do not require frequent changes: e.g., date,
time, or a variety of register functions.
MGR:
For manager’s and submanager’s entries
The manager can use this mode to make entries that are not permitted to be made by cashiers – for
example, after-transaction voiding and override entries.
X1/Z1: To take the X/Z report for various daily totals.
X2/Z2: To take the X/Z report for various periodic (weekly or monthly) consolidation of totals.
2 Drawer lock key
SK1-1
This key locks and unlocks the drawer. To lock it, turn 90 degrees counterclockwise. To unlock it, turn 90
degrees clockwise.
15
ER-A410/A420(SEC)-1
03.12.22 0:13 PM
Page 16
3 Cashier code entry key
✱
✱
✱
✱
Cashier codes are available in two variants: Variant 1, in which they are displayed (“0000” to “9999”), and
Variant 2, in which they are not displayed (always “
”).
When the cashier code is assigned by the following procedure, the register prints the four-digit cashier code
(variant 2: “
”) and the cashier name both on the receipt and journal for every transaction.
✱
✱
✱
✱
Procedure
■ Sign-on
■ Sign-off
Variant 1 / Variant 2 :
To display the current cashier code
Variant 1 :
(Code is displayed.)
Variant 2 :
(Code is not displayed.)
Note
Cashier code
‹
Cashier code
‹
‹
‹
‹
All of these settings depend on how the register has been programmed. For the selection of these
settings, consult your local dealer.
4 Receipt ON/OFF function
You can disable receipt printing in the REG mode to save paper using the receipt function. To disable receipt
printing, press the q key in the OP X/Z position. This key toggles the receipt printing status ON and OFF. To
check the receipt printing status, turn the mode switch to the OP X/Z position or press the c key in the REG
mode. When the function is in the OFF status, the receipt off indicator “_” illuminates.
Note
16
Your register will print reports regardless of the receipt status. This means that the receipt roll must
be installed even when the receipt state is “OFF” when taking reports.
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 17
DISPLAYS
1 Operator display
The operator display consists of a two-line dot-matrix display (16 characters/line).
Price level / PLU level (e.g. P2L3)
Dept. name / PLU or UPC name / function text
Cashier code or mode name
Function message display area
Numeric entry display area
Receipt OFF indicator (“_”) / Stock alarm indicator (“•”)
Repeat / Sentinel mark / Power save mark
• Cashier code or mode name
The mode you are in is displayed. When a cashier is assigned, the cashier code is displayed in the REG
or OP X/Z mode. For example, “0001” is displayed when cashier 0001 is assigned.
• Repeat
The number of repeats is displayed, starting at “2” and incremental with each repeat. When you have
registered ten times, the display will show “0”. (2 ➞ 3 ......9 ➞ 0 ➞ 1 ➞ 2...)
• Sentinel mark
When amounts in the drawer reaches the amount you preprogrammed, the sentinel mark “X” is
displayed to advice you to remove the money to a safe place.
• Power save mark
When the cash register goes into the power save mode, the power save mark (decimal point) is
displayed.
• Stock alarm indicator
When the stock of the PLU or UPC which you entered is zero or negative, the alarm indicator (decimal
point) is displayed.
• Function message display area
Item labels of departments and PLU/subdepartments/UPC and function text you use, such as %1, (–)
and CASH are displayed here. For the details of function texts, please refer to pages 120 and 121.
When an amount is to be entered or entered, “AMOUNT” is displayed: When an amount is to be
entered, – – – – – – – is displayed in the numeric entry display area with “AMOUNT”. When a preset
price has been set, the price is displayed in the numeric entry display area with “AMOUNT”.
• Numeric entry display area
Numbers entered using numeric keys are displayed here.
Date and time display
Date and time appear on the display in the OP X/Z, REG, or MGR mode. In the REG or MGR mode, press
the = key to display the date and time.
Error messages
When an error occurs, the corresponding error message is displayed in the function message display area.
For the details of error messages, please refer to the “Error message table” on page 184.
2 Customer display (Pop-up type)
$
(• : Appears right below the seventh place when the item amount is displayed at scale entry.)
17
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 18
FOR THE OPERATOR
PRIOR TO ENTRIES
1 Preparations for entries
Before registrations, insert the operator key into the mode switch and turn it to the REG position and check the
following items:
Receipt and journal paper rolls
If the receipt and journal paper rolls are not set in the machine or there are low rolls, install new ones according
to section “4. Installing and removing the paper rolls” under “OPERATOR MAINTENANCE.”
Receipt ON/OFF function
You can disable receipt printing in the REG mode to save paper using the receipt function. To disable receipt
printing, press the q key in the OP X/Z position. This key toggles the receipt printing status ON and OFF.
To check the receipt printing status, turn the mode switch to the OP X/Z position or press the c key in the REG
mode. When the function is in the OFF status, the receipt off indicator “_” illuminates.
Note
Your register will print reports regardless of the receipt state. This means that the receipt roll must
be installed even when the receipt state is “OFF” when taking reports.
Cashier assignment
✱
✱
✱
✱
Prior to any item entries, cashiers must enter their cashier code into the register. The code entry may not be
necessary when the same cashier code is used in the next transaction.
Cashier codes are available in two variants: Variant 1, in which they are displayed (“0000” to “9999”), and
Variant 2, in which they are not displayed (always “
”).
When the cashier code is assigned by the following procedure, the register prints the four-digit cashier code
(variant 2: “
”) and the cashier name both on the receipt and journal for every transaction.
✱
✱
✱
✱
Note
The operation entries depend on how the register has been programmed. To determine which
selections should be considered, please consult your local dealer.
✱
✱
✱
✱
Cashier code
(“
” is printed in Variant 2.)
Cashier name
18
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 19
Procedure
■ Sign-on
■ Sign-off
Variant 1 / Variant 2 :
To display the current cashier code
Variant 1 :
(Code is displayed.)
Variant 2 :
(Code is not displayed.)
Note
Cashier code
‹
Cashier code
‹
‹
‹
‹
• If you want to enter a cashier code before every transaction, please consult your dealer.
• For the display type selection of the cashier code, “Variant 1” has been preset. For the selection of
the “Variant 2”, consult your dealer.
• The cashier can be changed during a transaction. Please consult our dealer.
2 Power saving mode
The register will enter into the power saving mode when no entries are performed based on the pre-programmed
time limit (by default, 30 minutes).
When the register goes to the power save mode, all display lights will turn off. This will be indicated by a decimal
point at the left most position of the lower line. The register will return to normal operation mode when any key is
pressed or a mode is changed with the mode key. Please note when the register is recovered by any key entry
and the initial key entry is ignored. After the recovery, you may start the key entries from the beginning.
3 Error warning
In the following examples, your register will go into an error state accompanied with a warning beep and a
corresponding error message. Clear the error state by pressing the c key and take proper action.
Please refer to the error message table on page 184.
• When you enter an over 32-digit number (entry limit overflow): Cancel the entry and re-enter a valid number.
• When you make an error in key operation: Clear the error and continue entries.
• When you make an entry beyond a programmed amount entry limit: Check to see if the entered amount is
correct. If it is correct, it be possible to make the entry in the MGR mode. Contact your manager.
• When an including-tax subtotal exceeds eight digits: Clear the subtotal by pressing the c key and press the
a, Å, k, CHK2 , or ' thru , key to finalize the transaction.
19
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 20
ENTRIES
1 Item entries
Single item entries
Procedure
Department entries (direct department entries)
Enter a unit price and press a department key. If you use a programmed unit price, press a department key only.
When using a programmed unit price
*Less than the programmed upper limit amounts
Unit price *
(max. 7 digits)
Note
Department key
When those departments for which the unit price has been programmed as zero (0) are entered,
only the sales quantity is added.
Department entries (indirect department entries)
When using a programmed unit price
Dept. code
(1–99)
à
Unit price *
(max. 7 digits)
à å
or
*Less than the programmed upper limit
amounts
When [preset only dept.] is entered.
PLU entries (indirect PLU entries)
Enter a PLU code and press the PLU/
key.
UPC
PLU/
UPC
PLU code
Note
When those PLU’s for which the unit price has been programmed as zero (0) are entered, only the
sales quantity is added.
Subdepartment (open PLU, open and preset PLU) entries
When using a programmed unit price
PLU code
PLU/
UPC
Unit price *
(max. 7 digits)
PLU entries (direct PLU entries)
When using a programmed unit price
Unit price *
(for subdept.)
20
Direct PLU key
PLU/
UPC
or
å
*Less than the programmed upper limit
amounts
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 21
UPC entries
Scan UPC code
Ä
PLU/
UPC
UPC code
(max.13 digits)
(Registration)
To cancel the learing function entry
To set “auto-delete”
Unit price
(max. 6 digits)
When the dept. key is depressed directly
NON
DELETE
(
å
Example
Key operation
1~
99
Dept. no.
(1 - 99)
c
)
DEPT
#
Print
1200 3
5
8à
5 à 680 à
PLU/
2P
UPC
PLU/
PLU/
11 P
1200
UPC
UPC
P
ô
PLU/
5012345678900 P
UPC
a
Repeat entries
You can use this function for entering a sale of two or more same items.
You can use the è key to repeat entry instead of department, å, direct PLU or
Example
Key operation
Repeated
department
entry (direct)
Repeated
department entry
(indirect)
Repeated PLU
entry
(indirect)
Repeated PLU
entry
(direct)
Repeated
subdepartment
entry
Repeated UPC
entry
Repeated
department entry
(direct) using the
repeat key
PLU/
UPC
key.
Print
200 8
8
8
5 à 680 à
à
10 P
P
P
ó
ó
60 P
500 P
P
5012345678900 P
P
600 2
è
è
a
PLU/
UPC
PLU/
UPC
PLU/
UPC
PLU/
UPC
PLU/
UPC
PLU/
UPC
PLU/
UPC
PLU/
UPC
21
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 22
Multiplication entries
Use this feature when you need to enter two or more same items.
This feature helps when you sell a large quantity of items or need to enter quantities that contain decimals.
Procedure
When using a programmed
unit price
Q’ ty
@
Unit price
Department key
Dept. code
à
Unit price
Dept. entry (direct)
à å
or
Dept. entry (indirect)
When [preset only dept.] is entered.
PLU code
PLU/
UPC
PLU code
PLU/
UPC
Unit price
PLU entry (indirect)
Unit price
Direct PLU key
Ä
UPC code
PLU/
UPC
or
å
PLU/subdept. entry (indirect)
PLU/subdept. entry (direct)
Scan UPC code
UPC entry
PLU/
UPC
• After scanning a UPC code or pressing the PLU/
UPC key, when the item does not exist in the file, the display will
show “NO RECORD”. Enter the unit price using the å key and department no. with the à key.
• Q’ty: Up to four digits integer + three digits decimal
• Unit price: Less than a programmed upper limit
• Q’ty × unit price: Up to seven digits
Example
Key operation
Department
entry (direct)
Department
entry
(indirect)
PLU entry
(indirect)
PLU entry
(direct)
Subdepartment
entry
UPC entry
Print
7 . 500 @
165 8
[email protected]
5à
250 à
15 @
PLU/
13 P
UPC
8 . 250 @
ò
[email protected]
PLU/
60 P
UPC
PLU/
100 P
UPC
[email protected]
PLU/
5012345678900 P
UPC
a
Note
22
You must use a decimal point (.) key when entering quantities that are fractional.
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 23
Successive multiplication entries
This function may be desired when you enter a sale of items sold by area (square feet).
Procedure
When using a
programmed unit price
@
Length
Width
Dept. code
@
à
Unit price
Unit price
Department key
à å
or
Dept. entry (direct)
Dept. entry (indirect)
When [preset only dept.] is entered.
PLU code
PLU/
UPC
PLU code
PLU/
UPC
Unit price
Unit price
PLU/
UPC
or
å
Direct PLU key
Ä
UPC code
PLU entry (indirect)
PLU/subdept. entry (indirect)
PLU/subdept. entry (direct)
Scan UPC code
UPC entry
PLU/
UPC
• After scanning a UPC code or pressing the PLU/
UPC key, when the item does not exist in the file, the display will
show “NO RECORD”. Enter the unit price using the å key and department no. with the à key.
• Length or width: Up to seven digits (4-digit integer + 3-digit decimal)
• Unit price: Less than a programmed upper limit
• Length × Width × Unit price: Up to seven digits
Note
• For actual use of this function, please consult your dealer.
• You must use a decimal point (.) key when entering quantities that are fractional.
Example
Key operation
Department entry
PLU entry
Subdepartment entry
UPC entry
Print
[email protected]
[email protected]
400 5
1 . 500 @
2 . 500 @
PLU/
8P
UPC
1 . 750 @
1 . 750 @
PLU/
UPC
6P
PLU/
UPC
600 P
[email protected]
[email protected]
PLU/
UPC
5099887654302 P
a
23
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 24
Split-pricing entries
You may use this function when your customer wants to purchase items normally sold in bulk.
Procedure
When using a
programmed unit price
@
Selling q’ty
Base q’ty
@
Unit price
per base q’ty
Dept. code
Department key
à
Unit price
à å
or
When [preset only dept.] is entered.
PLU code
PLU/
UPC
PLU code
PLU/
UPC
Unit price
per base q’ty
Direct PLU key
Unit price
per base q’ty
PLU/
UPC
or
å
PLU/
UPC
or
å
Ä
UPC code
Only when you use a
base q’ty programmed
for PLU code
PLU/
UPC
PLU code
PLU/
UPC
PLU code
PLU/
UPC
Unit price
per base q’ty
Direct PLU key
Unit price
per base q’ty
Ä
UPC code
PLU/
UPC
• After scanning a UPC code or pressing the PLU/
UPC key, when the item does not exist in the file, the display will
show “NO RECORD”. Enter the unit price using the å key and department no. with the à key.
• Selling quantity: Up to four digits integer + three digits decimal
• Base quantity: Up to two digits (integer)
Example
Key operation
Department
entry
PLU entry
UPC entry
Print
[email protected]
10 @
600 7
[email protected]
[email protected]
PLU/
35 P
UPC
[email protected]
[email protected]
PLU/
UPC
5045678912304 P
a
Note
24
You must use the decimal point (.) key when entering selling quantities that are fractional.
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 25
Single item cash sale (SICS)/single item finalize (SIF) entries
SICS entries
• This function is useful when a sale is for only one item and is for cash; such as a pack of cigarettes. This
function is applicable only to those departments that have been set for SICS or to their associated PLUs,
subdepartments or UPCs.
• The transaction is finalized and the drawer opens as soon as you press the department key, å key, PLU/
UPC key,
the direct PLU key or scanning a UPC code.
Example
Key operation
Print
250
For finishing
the transaction
Note
9
If an entry to a department, PLU/subdepartment or UPC set for SICS follows entries to
departments, PLUs/subdepartments or UPC not set for SICS, it does not finalize and results in a
normal sale.
SIF entries
• If an entry to a department, PLU/subdepartment or UPC set for SIF follows entries to departments,
PLUs/subdepartments or UPC not set for SIF, the transaction is finalized immediately as a cash sale.
• Like the SICS function, this function is available for single-item cash settlement.
Example
Key operation
Print
1745 8
1500
For finishing
the transaction
9
25
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 26
Scale entries
For making entries for weighed items, a scale must be connected where by the weight is automatically read from
the scale. To make refund entries, the weight is entered manually while the scale platter is empty and reads
zero.
i) Auto scale entries
Procedure
When using a
programmed unit price
When base wt. is
1 LB (or 1 KG)
Unit price
per base wt.
Dept. code
When you use a
programmed tare no.
Tare number
(1-9)
OPEN
TARE
Department
à
Unit price
à å
or
When [preset only dept.] is entered.
SCALE
Base wt.
`
Unit price
per base wt.
Dept. code
Open tare
weight
Department
à
Unit price
à å
or
When [preset only dept.] is entered.
PLU code
PLU/
UPC
PLU code
PLU/
UPC
Unit price
per base wt.
Direct PLU key
Unit price
per base wt.
PLU/
UPC
or
å
PLU/
UPC
or
å
Ä
UPC code
Only when you use a
base wt. programmed
for PLU code
PLU/
UPC
PLU code
PLU/
UPC
PLU code
PLU/
UPC
Unit price
per base wt.
Direct PLU key
Unit price
per base wt.
Ä
UPC code
PLU/
UPC
• Open tare weight: Up to 5 digits (integer + decimal)
• Net weight:
Up to 5 digits (integer + decimal)
• Base weight:
Up to 2 digits (integer)
Note
• The register can be programmed with up to nine tare tables and allows different tares to be
assigned to them.
• When the S key is pressed, the weight is automatically read from the connected scale (option)
and the net weight appears in the register display.
• When the item is programmed for “Scale compulsory”, it is not necessary to press the S key.
Example
Key operation
S 200 1
S1P
c
PLU/
UPC
26
Print
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 27
ii) Manual scale entries of refunded items
Procedure
When using a
programmed unit price
When base wt. is
1 LB (or 1 KG)
Unit price
per base wt.
Dept. code
Department
à
Unit price
à å
or
When [preset only dept.] is entered.
Net weight
Ï
SCALE
Base wt.
`
Unit price
per base wt.
Dept. code
Department
à
Unit price
à å
or
When [preset only dept.] is entered.
PLU code
PLU/
UPC
PLU code
PLU/
UPC
Unit price
per base wt.
Direct PLU key
Unit price
per base wt.
PLU/
UPC
or
å
PLU/
UPC
or
å
Ä
UPC code
Only when you use a
base wt. programmed
for PLU code
PLU/
UPC
PLU code
PLU/
UPC
PLU code
PLU/
UPC
Unit price
per base wt.
Direct PLU key
Unit price
per base wt.
Ä
UPC code
PLU/
UPC
• Net weight: Up to 5 digits (integer + decimal) which is from the customer’s receipt.
• Base weight: Up to 2 digits (integer)
Example
Key operation
Print
32 . 45 Ï S 200 1
PLU/
32 . 45 Ï S 1 P
UPC
c
27
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 28
PLU level shift (for direct PLU)
This shift can double or triple the number of PLUs on your register without adding additional direct PLU keys.
You can use direct PLUs in three levels by utilizing shift keys l, ¬, and Ò. These keys have the following
functions.
l: Shifts the PLU level from level 2 or 3 to level 1 (ordinary level).
¬: Shifts the PLU level from level 1 or 3 to level 2.
Ò: Shifts the PLU level from level 1 or 2 to level 3.
You must program your machine in the PGM2 mode to select one of the two PLU level shift modes — automatic
return mode* and lock shift mode** — and decide whether to allow PLU level shift in both the REG and MGR
modes or in the MGR mode alone.
* The automatic return mode automatically shifts the PLU level back to level 1 after a direct PLU key is pressed.
You can select whether the PLU level should return each time you enter one item or each time you finalize
one transaction.
** The lock shift mode holds the current PLU level until a PLU level shift key is pressed.
Automatic return mode
If you shift the PLU level while in the automatic return mode, press the desired PLU level shift key before
numeric entries.
Procedure
• each item
¬
Ò
Numeric entry
(Q’ty,
@
Direct PLU
)
• each transaction
¬
Ò
Numeric entry
(Q’ty,
@
Direct PLU
Payment
)
Lock shift mode
If you shift the PLU level while in the lock shift mode, press the desired PLU level shift key before numeric
entries.
Procedure
To shift the level of another PLU
l
¬
Ò
Note
28
Numeric entry
(Q’ty,
@
Direct PLU
)
If you select the automatic return mode, it is not necessary to use the l key on the keyboard, but
if you select the lock shift mode, it is necessary to use the key.
ER-A410/A420(SEC)-2
Example
03.12.22 0:13 PM
Page 29
Direct PLU1: PLU code 1 (PLU level 1), PLU code 65 (PLU level 2)
Direct PLU2: PLU code 2 (PLU level 1), PLU code 66 (PLU level 2)
• When your machine has been programmed for the automatic return mode:
Key operation
Print
1
¬1
2
1
a
• When your machine has been programmed for the lock shift mode:
Key operation
Print
l1
¬1
2
1
a
29
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 30
PLU/UPC price level shift
Two different price levels can be programmed for each PLU or UPC.
The price levels can be changed for PLU or UPC registrations.
You can shift the PLU/UPC price level (level 1 or 2) by utilizing the price level shift key ( ˘
SHIFT ).
You must program a price level shift mode (i.e. automatic return mode* or lock shift mode**) and the operating
mode to be used for the price level shift (i.e. both REG/MGR modes or MGR mode alone).
* The automatic return mode automatically shifts the PLU/UPC price level back to level 1 after a PLU/UPC shift
entry. You can select whether the price level should return each time you enter one item or each time you
finalize one transaction.
** The lock shift mode holds the current PLU/UPC price level until pressing the price level shift key.
Automatic return mode (for price level)
If your register has been programmed for the price level shift in the automatic return mode, press the price level
shift key before a numeric entry.
Procedure
(each item)
Ä
˘
Numeric entry
SHIFT
(Q’ty,
@
PLU/UPC code
PLU/
UPC
etc.)
Direct PLU
(each transaction)
˘
Ä
Numeric entry
SHIFT
(Q’ty,
@
PLU/UPC code
PLU/
UPC
Payment
etc.)
Direct PLU
Lock shift mode (for price level)
If your register has been programmed for the price level shift in the lock shift mode, press the price level shift
key before a numeric entry.
Procedure
To shift the price level of another PLU/UPC
˘
Ä
Numeric entry
SHIFT
(Q’ty,
@
PLU/UPC code
etc.)
PLU/
UPC
Direct PLU
Note
30
You can program “printing of the price level text (LEVEL 1/LEVEL 2)”. Please refer to
“Programming for optional feature selection” described in the “PROGRAMMING” section of this
manual.
ER-A410/A420(SEC)-2
Example
03.12.22 0:13 PM
Page 31
PLU price level 1: PLU 1 ($1.91), PLU 2 ($0.79)
PLU price level 2: PLU 1 ($2.00), PLU 2 ($0.99)
• When your register has been programmed for the automatic return mode (by one item):
Key operation
˘
SHIFT
Print
PLU/
1P
UPC
PLU/
1P
UPC
PLU/
2P
UPC
a
• When your register has been programmed for the lock shift mode:
Key operation
Print
1P
PLU/
1P
UPC
PLU/
2P
UPC
PLU/
UPC
˘
SHIFT
a
Set PLU entries
Operations are the same as normal PLU’s.
When a set PLU is entered, an entered or preset amount is printed as the unit price and then those PLUs linked
to the set PLU are printed automatically.
Example
Key operation
Print
p
a
Note
The unit price of the set PLU (ex. PLU 20) is the registered amount of the set PLU. The tied PLU’s
memory is updated only by the entered quantity.
31
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 32
Link PLU/UPC entries
The operation is the same as normal PLU’s/UPC’s. When this PLU/UPC is entered, the linked PLU’s amount is
included and the linked PLU’s label is printed automatically. Only the 1st PLU is affected by the status shift keys
TAX
( SHIFT
, |, «, » or ˛ key). The percent calculation is in effect for the amount of the 1st ranking PLU.
Example
When PLU 21 is linking PLU 25,26,27 as follows
Key operation
Print
PLU/
UPC
21 P
a
Age verification (Birthday entry)
The age verification function is used for prohibiting the sale of goods (departments, PLUs or UPCs) for certain
aged persons based on a registered birthday.
When a department/PLU/UPC for which a figure other than zero (01 to 99) has been programmed as the age
limitation is entered, a birthday entry must be completed.
Procedure
XXXXXX
BIRTH
Birthday (five or six digits)
Note
• A birthday entry can be performed two or more times at any point during a transaction, however
the last entered birthday remains in effect.
• You can enter the date as far back as 98 years.
[Ex.] When the current year is 2005 : you can enter the year 1907-2005.
Example
Oct. 2, 1985 (When dept. 17 is programmed as the age limitation “17”.)
Key operation
Print
100285 BIRTH
17
300 7
a
When the preset option for “Birthday print availability (#2616)” is programmed as “Allow”, the birthday date is
printed.
32
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 33
Mix-and-match entries
This function is convenient for matching several PLU/UPC items and selling them in a lump (e.g. bundle sale,
multi-packed sale, etc.). The matching q’ty and adjusted amount are assigned to a mix-and-match table. All
items that are programmed into the same table are treated as if they belong to one group.
Example
Selling on a mix-and-match basis the following items in table no. 1 to which the matching q’ty
“3” and the adjusted amount “$10.00” are assigned:
• PLU 40 (Unit price: $5.00)
• PLU 41 (Unit price: $3.00)
• PLU 42 (Unit price: $2.50)
Key operation
Print
Treated as $5.00 item ➝ /
Treated as $3.00 item ➝ !
Treated as $2.00 item ➝ @
a
Price inquiry (view) function (for PLU/UPCs)
You can use this function when you want to know the unit price of the PLU/UPC item during transaction in the
REG/MGR mode.
Procedure
Scan UPC code
The total sales amount of
the UPC is displayed.
Ä
Numeric entry
Ù
(Q'ty
`
)
UPC code
PLU/
UPC
PLU code
PLU/
UPC
Direct PLU
*1
c
å
*2
*3
(MGR mode) Unit price
å
*1: Press the c key to cancel the inquiring (view) mode.
*2: Press the å key when you want to register the unit price of the PLU/UPC displayed.
*3: You can change the unit price temporarily in the MGR mode. The unit price which is programmed in PGM
mode is not changed (Price override entry).
For the repeat entry, use the è key.
Note
Example
Key operation
Print
P
Ù
5089123456708 P
å
c
5
Price is displayed.
PLU/
UPC
PLU/
UPC
33
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 34
UPC learning function
When you enter or scan an undefined code, you are required to enter the unit price “amount” and the associated
department. The UPC code, unit price and the department entered are stored in the UPC file and is used for
future sales entries.
Note
• When there is no capacity remaining in the file, the data is not stored in the file.
• The text of the entered department is applied to the entered UPC code.
• You can use the UPC learning function in the training mode. This may be convenient to practice
when installing the scanning system.
Procedure
“NO RECORD” is displayed and
the beep sound occurs three times.
Scan an undefined UPC code
Ä
Undifined
UPC code
When the unit price is zero, or in case of
non-PLU type UPC code having price info.
or press code.
*
PLU/
UPC
Ì
Unit price
Department key
å
c
Dept. no.
à
To cancel the operation
“ENTER DEPT#”
is displayed
* Press the Ì key when you want to exempt the UPC code entered from the non-accessed UPC delete
function (deletion occurs by executing #105 in Z1 mode).
Note
For the repeat entry, use the è key.
Example
“NO RECORD” is displayed.
Key operation
Print
PLU/
5056789123404 Û
UPC
750
5
c
34
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 35
Price change function (for UPCs)
You can use this function when you need to change the unit price or associated department of a UPC item in
REG/MGR mode.
There are two methods for price changes:
1. Price change mode
You can change the preset price and/or the associated department of a UPC item without entering PGM
mode.
2. Changing a price during a transaction
When a wrong UPC price and/or associated department is found during transaction, you can correct them at
the time of the transaction. With the entry of a new price and/or associated department, the preset price
and/or associated department is automatically changed to the new price and/or associated department.
Note
For the Non-PLU type price embedded UPC-A codes and press codes, the prices in the codes
have the priority over the preset prices. So, for these codes, a changed price is valid only when the
price change is executed.
Procedure
Price change mode
“PRICE CHANGE” is displayed.
Scan UPC code
Ä
Ê
UPC code
PLU/
UPC
Changing a price during a transaction
Scan UPC code
Ä
UPC code
PLU/
UPC
Ê
“PRICE & DEPT” is displayed.
Ê
To change the unit price only
To enter 0
Unit price
c
To cancel
To change the associated dept.
directly by depressing the
corresponding key
Department key
å
Dept no.
à
To change the associated dept.
using the dept. no. entry key
35
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 36
Example
• Price change mode
Key operation
Print
Ê
PLU/
5087654321106 Û
UPC
600 Ê
• Changing a price during a transaction
Key operation
Print
PLU/
5087654321106 Û
UPC
Ê
600 Ê
c
The journal printer prints the
following format in this position.
Associated dept. no.
Note
36
• When an undefined code is entered in the price change mode, the register results in an error.
• When you press the Ê key during a transaction, the UPC entry is voided upon the 1st
depression of the Ê key, then you are allowed to enter a correct price and/or associated
department.
• When an associated department is changed, the item label for the department will be also
changed automatically to the item label of new associated department entered.
• For the repeat entry, use the è key.
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 37
2 Displaying and printing subtotals
Your register provides these five types of subtotals:
Merchandise subtotal
Press the  key at any point during a transaction. The net sale subtotal - not including tax - will appear in the
display.
Taxable subtotal
Taxable 1 subtotal
TAX
Press the SHIFT
and ı keys in this order at any point during a transaction. The sale subtotal of taxable
1 items will appear in the display.
Taxable 2 subtotal
Press the | and ı keys in this order at any point during a transaction. The sale subtotal of taxable 2
items will appear in the display.
Taxable 3 subtotal
Press the « and ı keys in this order at any point during a transaction. The sale subtotal of taxable 3
items will appear in the display.
Taxable 4 subtotal
Press the » and ı keys in this order at any point during a transaction. The sale subtotal of taxable 4
items will appear in the display.
Including-tax subtotal (full subtotal)
Press the ı key at any point during a transaction. The sale subtotal including tax will appear in the display.
Food stamp-eligible subtotal
Press the f key at any point during a transaction. The sale subtotal of items eligible for food stamp payment
will appear in the display.
Tray subtotal
Press the y key during a transaction in the REG or MGR mode.
The contents of the tray total itemizer which include tax are printed and displayed.
37
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 38
3 Finalization of transaction
Cash or Check tendering
Press the ı key to get an including-tax subtotal, enter the amount tendered by your customer, then press the
a or Å key if it is a cash tender or press the k or CHK2 key if it is a check tender. When the amount
tendered is greater than the amount of the sale, your register will show the change due amount and the text
“CHANGE”. Otherwise your register will show the text “DUE” and a deficit. Make a correct tender entry.
Example
Your customer pays $10.00 for an including-tax subtotal of $7.35.
Cash tendering
Key operation
Print
ı
1000 a
Check tendering
Key operation
Print
ı
1000 k
Mixed tendering (check + cash)
Example
Your customer pays $10.00 by check and $5.00 in cash for an including-tax subtotal of $14.56.
Key operation
ı
1000 k
500 a
38
Print
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 39
Cash or Check sale that does not need any tender entry
Enter items and press the a or Å key if it is a cash sale or press the k or
register will display the total sale amount.
Example
CHK2
key if it is a check sale. Your
Selling a $3.00 item (dept. 6) and another $7.15 item (PLU 10) for cash
Key operation
Print
300 6
PLU/
10 P
UPC
a
In the case of check sale
Charge (credit) sale
Enter items and press the corresponding charge keys (' thru ,).
Example
Selling a $25.00 item (dept. 6) and a $32.50 item (dept. 7) and accepting the payment by
charge account
Key operation
Print
2500 6
3250 7
'
Amount tendering operations (i.e., change calculations) can be achieved by the ' thru , key when it has
been preset in PGM2 job #2320.
Mixed-tender sale (cash or check tendering + charge tendering)
Example
Your customer pays $9.50 in cash and $40.00 by charge for an including-tax subtotal of
$49.50.
Key operation
Print
ı
950 a
'
Note
Press the k or CHK2 key or the ' thru , keys in place of the a key when your customer
makes payment by checks or by charge cards.
39
ER-A410/A420(SEC)-2
03.12.22 0:13 PM
Page 40
4 Food stamp calculations
Food stamp tendering
If your customer makes payment (or tendering) in food stamps, obtain the food stamp-eligible subtotal* by
pressing the f key and make a food stamp tender entry before entering a cash or check tender.
Note
The food stamp-eligible subtotal* depends upon how your register is programmed based on the
food stamp-eligibility of the automatic tax on a sale of items eligible for food stamp payment, or
whether your register is programmed to allow the automatic tax to be paid with food stamps or not
or to exempt taxation. The example below presupposes that your register has been programmed
to exempt taxation.
When the amount tendered in food stamps is greater than the food stamp-eligible subtotal:
Your register shows two change due amounts in its display.
The food stamp change due appears at the left of the display in dollars and the cash change at the right in cents.
• When you sell only items eligible for food stamp payment.
Example
Your customer purchases a $4.25 item (dept.4, taxable 1, eligible for food stamp payment)
and another $4.00 item (PLU 34, taxable 2, eligible for food stamp payment) and tenders
$10.00 food stamps for them.
Key operation
Print
425 4
34 P
UPC
To display
the food
stamp-eligible
subtotal
f
1000 f
Display shows:
Food stamp
change due
Cash change
due
Food stamp
change
Cash
change
• Mixed sale of an item eligible for food stamps and another item not eligible for food stamps
Example
Your customer purchases a $2.48 item (dept. 5, taxable 1, eligible for food stamps) and
another $5.42 item (dept. 8, nontaxable, ineligible for food stamps) and pays $5.00 in food
stamps and $5.00 in cash.
Key operation
Print
248 5
542 8
f
500 f
500 a
Display shows:
Food stamp
change due
Cash change
due
Food stamp
change
40
Cash
change
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 41
When the food stamp tender is smaller than the food stamp-eligible subtotal:
• Accept the remainder in food stamps or in cash or check. If your register is programmed to exempt taxation,
additional food stamp tender is not allowed.
Example
Your customer buys a $3.18 item (dept. 5, taxable 1, eligible for food stamps) and another
$1.24 item (dept.7, taxable 2, eligible for food stamps) and pays $4.00 in food stamps and the
remainder - $1.00 in cash.
Key operation
Print
318 5
124 7
f
To enter the
cash tendering
of the remainder
400 f
100 a
Food stamp status shift
Your machine allows you to shift the programmed food-stamp status of each department, - thru ≠, percent
key or the PLU key by pressing the ˛ key prior to those keys. After each entry is completed, the programmed
food stamp status is resumed.
Example
You sell a $2.32 item of dept. 2 (food-stamp eligible) as a food-stamp ineligible item and
another $3.18 item of PLU 86 (food-stamp ineligible) as a food-stamp eligible item and accept
$4.00 in food stamps and $2.00 in cash.
Key operation
Print
232 ˛ 2
PLU/
86 ˛ P
UPC
f
400 f
200 a
41
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 42
5 Tax calculations
Automatic tax
When your register is programmed with a tax table (or tax rate) and the tax status of an individual department
and PLU is set for taxable, it computes the automatic tax on any item that is entered directly into the department
or indirectly via a related PLU.
Example
Selling five $6.70 items (dept. 1, taxable 1) and one $7.15 item (PLU 85, taxable 2) for cash
Key operation
Print
[email protected]
670 1
PLU/
85 P
UPC
a
Manual tax
Your machine allows you to enter tax manually after item entries.
Example
Selling an $8.00 item (dept. 7) for cash with 50 cents as tax
Key operation
800 7
50 †
a
42
Print
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 43
Automatic-tax delete
You can delete the automatic tax on the taxable 1, taxable 2, taxable 3 and taxable 4 subtotal of each
transaction by pressing the † key after the subtotal is displayed.
Example
Selling a $7.25 item (dept. 1, taxable 1) and another $5.15 item (dept. 3, taxable 2) for cash
and entering the sale as a non-taxable one
Key operation
Print
725 1
515 3
\ı
†
|ı
†
a
TAX
SHIFT
If any of the media keys (i.e. cash, check or charge 1 thru charge 5) are programmed as tax delete in PGM2
mode, the tax can be deleted without using the procedures above. In this case, depressing a corresponding
media key alone will always cause the programmed tax to be deleted.
Example
When the Å key is programmed as tax delete for the same case with the above example
Key operation
Print
725 1
515 3
Å
43
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 44
Tax status shift
Your machine allows you to shift the programmed tax status of each department, - thru ≠, percent key or
TAX
the PLU key by pressing the SHIFT
, |, « and/or » keys before those keys. After each entry is completed,
the programmed tax status of each key is resumed.
Example
Selling the following items for cash with their programmed tax status reversed
• One $13.45 item of dept. 7 (non-taxable) as a taxable 1 item
• One $7.00 item of PLU 25 (non-taxable) as a taxable 1 and 2 item
• One $4.00 item of dept. 3 (taxable 2) as a non-taxable item
• Two $10.50 items of dept. 1 (taxable 1) as taxable 2 items
Key operation
Print
1345 \ 7
PLU/
UPC
25 \ | P
400 | 3
1050 \ | 1
TAX
SHIFT
TAX
SHIFT
TAX
SHIFT
1
a
Note
The entry of a multi-taxable item for PST or GST will be prohibited as follows (for Canada).
In case of; Tax 1: PST, Tax 2: PST,
Tax 3: PST, Tax 4: GST
Taxable 1 and 2 item ········· prohibited
Taxable 1 and 3 item ········· prohibited
Taxable 2 and 3 item ········· prohibited
Taxable 1 and 4 item ············· allowed
Taxable 2 and 4 item ············· allowed
Taxable 3 and 4 item ············· allowed
44
In case of; Tax 1: PST, Tax 2: PST,
Tax 3: GST, Tax 4: GST
Taxable 1 and 2 item ········· prohibited
Taxable 1 and 3 item ············· allowed
Taxable 2 and 3 item ············· allowed
Taxable 1 and 4 item ············· allowed
Taxable 2 and 4 item ············· allowed
Taxable 3 and 4 item ········· prohibited
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 45
6 Guest Check (PBLU)
This feature is used to store and recall previous or credit balances of an open charge account when a previous
balance lookup (PBLU) code is entered. The PBLU code can be 1 to 9999.
New charge accounts
For a new customer, open a new charge account by assigning a PBLU code.
Procedure
For automatic PBLU
code generation
PBLU code
(1-9999)
n
Amount
Note
[Item entries]
r or A
S
f
[Payment operations]
Ω
∏
• The PBLU code refers to a code that will be used whenever the guest check must be accessed for
re-ordering or final payment.
• Your register can be programmed to generate PBLU codes in a sequential fashion. If your register
has not been programmed to do so, each PBLU code can be entered manually.
• When the S key is pressed, the tax is not calculated.
• You can temporarily finalize a guest check by pressing the f key. This print out of the guest
check will show the current balance, including tax. The guest check, however, is still “open”. This
means you can still make additional orders to it.
Example
Key operation
Print
111 n
3500 2
2700 3
f
45
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 46
Additional item entries
For making additional guest check entries, enter the PBLU code first for automatic PB lookup.
Procedure
PBLU code
(1-9999)
u
Amount
S
f
[Item entries]
r or A
[Payment operations]
Ω
∏
Example
Key operation
Print
111 u
1400 5
1600 6
f
Settlement
Use the following procedure:
Procedure
PBLU code
(1-9999)
u
Amount
[Item entries]
r or A
[Payment operations]
Ω
∏
Example
Key operation
111 u
9410 r
8000 k
1410 c
46
Print
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 47
Deposit entries
Deposit refers to a payment on a charge account. It can be received in cash, check or by charge. You can make
the deposit entry only while in a guest check transaction. It cannot be done during handling of a tendered
amount.
A received deposit can be refunded by pressing the DEPO
RFND key. You cannot attempt to refund an amount larger
than the deposit balance.
Procedure
DEPO
Deposit
amount
DEPO
RFND
Example
k
c
'
or
or
thru
CHK2
Å
,
To record a $50.00 deposit in cash made by a customer with PBLU code 111
Key operation
Print
111 u
DEPO
5000 5
Å
S
Example
To refund a $50.00 deposit made by a customer with PBLU code 111
Key operation
Print
111 u
DEPO
5000 5
RFND
Å
S
47
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 48
7 Auxiliary entries
Percent calculations (premium or discount)
• Your register provides the percent calculation for the merchandise subtotal and item entries. You need to
specify in advance whether the register should perform the percent calculation based on the merchandise
subtotal or each item entered.
• Percentage: 0.01 to 99.99%
Percent calculation for the merchandise subtotal
Example
Selling four $1.40 items of dept. 5 and two $2.25 items of dept. 7; all these items are sold for
cash at a premium of 10%
(This example presumes that a premium of 10% has been programmed for the % key.)
Key operation
Print
[email protected]
140 5
225 7
7
Â
%
a
Percent calculation for item entries
Example
Selling for cash an $8.00 item of dept. 6 at a discount of 15% and another $5.00 item of PLU
90 at a discount of 7.5%
(This example presumes that a discount of 15% has been programmed for the § key.)
Key operation
800 6
§
PLU/
90 P
UPC
7.5§
a
48
Print
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 49
Discount entries
For discount or coupon tenderings, you may use the - thru ≠ key.
If the discount or tendered coupon is the one applicable to sales, use the vendor coupon or if it is applicable to
each department key, use the store coupon.
Discount for the merchandise subtotal
Example
Selling a $5.75 item of dept. 6 and another $7.50 item of PLU 80 for cash after subtracting the
discount amount $1.00 from the total sale amount
(This example presumes that the vendor coupon has been programmed for the – key.)
Key operation
Print
575 6
PLU/
UPC
80 P
100 –
a
Discount for item entries
Procedure
Amount
Dept. code
PLU code
UPC code
Example
Dept.
- $
thru
-
thru
thru
thru
thru
Direct PLU
$
$
$
$
à
Amount
PLU/
UPC
Amount
à å
å
or
PLU/
UPC
or
PLU/
UPC
Ä
Selling a $6.75 item of dept. 7 for cash after subtracting the coupon amount 75¢
(This example presumes that the store coupon has been programmed for the - key.)
Key operation
Print
675 7
75 -
*
Note
*
7
a
The - is entered as a modifier for the department which will be netted by the coupon amount.
Such item netting coupon entries may generally be entered at any point within a transaction. Two
lines are printed for each entry: The first is the label programmed for the - function and the
second is related department and - amount.
49
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 50
Refund entries
If a refund item is the one entered into a department, enter the amount of the refund, then press the Ï key and
the corresponding department key in this order; and if an item entered into a PLU (or UPC) is returned, enter the
UPC
corresponding PLU (or UPC) code, then press the Ï and PLU/
keys, or press the Ï and direct PLU keys
without entry of PLU code, in this order.
Example
Receiving the following items returned:
One $2.50 item of dept.6 and seven $2.10 items of PLU 13
Key operation
Print
250 Ï 6
[email protected]
PLU/
13 Ï P
UPC
a
Refund sales mode
This function is used for those item return entries relating to departments, PLUs/subdepartments and UPCs.
Pressing the ˜ key at the beginning of a transaction causes the register to enter the REFUND SALES mode.
All of the REFUND SALES mode entries are automatically handled as refund entries. This mode cannot be
finalized by check payment entry.
Example
Receiving the following items returned:
One $2.50 item of dept.6 and seven $2.10 items of PLU 13
Key operation
Print
˜
250 6
[email protected]
PLU/
13 P
UPC
a
Printing of non-add code numbers
Enter a non-add code number such as a customer’s reference number within a maximum of 16 digits and press
the = key at any point during the entry of a sale. Your register will print it at the time of entry.
Example
Selling a $15.00 item of dept. 6 by charge account to a customer whose code number is 1230
Key operation
1230 =
1500 6
'
50
Print
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 51
8 Payment treatment
Currency conversion
Your register allows payment entries of foreign currency. Pressing the ç thru $ key creates a subtotal in
foreign currency. Cash payment is the only media that can be handled after currency conversion.
Procedure
For an additional payment in foreign currency
After an entry
is completed
or
After the amount
tendered is found
smaller than the
sales amount in
a sales entry.
For direct finalization
Preset rate
*Rate
ç
"
#
$
Amount
tendered
(max. 8 digits)
c
Reentry
a
Å
Next registration
or
payment in
domestic currency
*Rate: 0.000000 to 999.999999
Note
When the amount tendered is short, the deficit is shown in domestic currency.
Example
To convert the amount owed ($69.50) into the designated foreign currency
Preset rate (1.325) - CONV 1
Key operation
Print
2300 6
4650 7
Currency
conversion
ç
Amount
tendered in
foreign currency
10000 a
Domestic
currency
Conversion rate
Foreign currency
Domestic
currency
Manual rate - CONV 4 (The $ key can be used only for the manual entry.)
Key operation
Print
2300 6
4650 7
1 . 275 $
10000 a
Conversion
rate
51
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 52
Received on account entries
Procedure
a Å
k CHK2
' ,
f
or
Amount
(max. 8 digits)
Example
r
®
or
or
thru
A customer whose reference number is 12345 tenders $48.00 by check for received on
account.
Key operation
Print
12345 =
4800 r
k
Paid out entries
Procedure
a Å
k CHK2
' ,
f
or
Amount
(max. 8 digits)
Example
p
π
or
or
thru
You pay $30.00 by check to a vendor whose code number is 6789.
Key operation
Print
6789 =
3000 p
k
No sale (exchange)
Simply press the n key without any entry. The drawer will open and the printer will print “NO SALE” on both
the journal and the receipt. If your machine is preset to print a non-add code number before pressing the n
key, a no sale entry is achieved with a non-add code number printed.
52
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 53
Cashing a Check
Enter the check amount, then press the k or
CHK2
key.
Procedure
Non-add code
number
Example
=
Check
amount
k
or CHK2
Cashing a check of a $30.00 amount
Key operation
Print
6789 =
3000 k
Bottle return
This function is used to handle the payment (paid out) for returned empty bottles or cans.
Example
You pay for ten 15¢ returned empty bottles. (This example presupposes that dept. 11 has
been programmed as bottle return department.)
Key operation
Print
10 @
15
a
9 Automatic sequencing key (` key) entries
You can achieve many different key sequences automatically with a single key depression by using the Auto
function key.
Example
Performing the transaction “Selling a $5.00 item (dept. 7) for cash” programmed for the ¡
(¡ = 500 7 a)
Key operation
Print
¡
53
ER-A410/A420(SEC)-2
03.12.22 5:41 PM
Page 54
CORRECTION
1 Correction of the last entry (direct void)
If you make an incorrect entry relating to a department, PLU/subdepartment, UPC, percentage (% through
•), deduction (- through ≠) or refund, you can correct this entry by pressing the v key immediately after
the incorrect entry.
Example
Key operation
Print
1250 6
v
PLU/
2P
UPC
v
PLU/
5012345678900 P
UPC
v
600 8
§
v
328 9
28 - 9
v
250 Ï 8
v
a
2 Correction of the next-to-last or earlier entries (indirect void)
With the v key, you can void any incorrect department, PLU/subdepartment, UPC or item refund entry made
during a transaction if you find it before finalizing the transaction (e.g. pressing the a key). This function is
applicable to department, PLU/subdepartment, UPC and item refund entries only.
For the operation, press the v key just before you press a department key, à key, direct PLU key,
just before you scan a UPC code. For the refund indirect void, press the v key after you press the
Ï key.
Example
Key operation
Print
1310 6
1755 7
PLU/
10 P
UPC
ô
PLU/
58 P
UPC
825 7
PLU/
5012345678900 P
UPC
1310 v 6
vô
PLU/
58 v P
UPC
PLU/
5012345678900 v P
UPC
a
54
PLU/
UPC
key or
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 55
3 Subtotal void
You can void an entire transaction. Once the subtotal void is executed, the transaction is aborted and the
register issues a receipt.
Example
Key operation
Print
1310 1
1755 6
PLU/
10 P
UPC
PLU/
35 P
UPC
Subtotal void
ı
v
ı
Correction of incorrect entries not handled by the direct or indirect void
4 function
Any errors found after the entry of a transaction has been completed or during an amount tendered entry, cannot
be voided. These errors must be handled by the manager.
The following steps should be observed:
1.
2.
3.
If you are in the middle of making an amount tendered entry, you must first finalize the transaction before
making corrections.
Try to make correct entries from the beginning.
Hand the incorrect receipt to your manager for its cancellation.
55
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 56
CORRECTION AFTER FINALIZING A
TRANSACTION
(AFTER GENERATING A RECEIPT)
When you need to void incorrect entries that are found after finalizing a transaction or cannot be corrected by
direct or indirect void, follow this procedure in the MGR mode.
1.
2.
3.
Turn the mode switch to the MGR position.
Press the v key to put your register in the VOID mode.
Repeat the entries that are recorded on an incorrect receipt. (All data for the incorrect receipt are removed
from register memory; the voided amounts are added to the void register totalizer.)
Incorrect receipt
Note
56
Cancellation receipt
Your machine leaves the VOID mode whenever a transaction is canceled (i.e. finalized in the VOID
mode.) To void additional transactions repeat steps 2. and 3. above.
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 57
OVERRIDE ENTRIES
Programmed limits (such as maximum amounts) for functions can be overridden by making the entry in the
MGR mode.
Procedure
1.
2.
Turn the mode switch to the MGR position.
Make the override entry.
Example
Selling a $15.00 item (dept. 2) for cash and subtracting the coupon amount $2.50 from the
sale amount (This example presumes that the register has been programmed not to allow
coupon entries over $2.00.)
Key operation
REG-mode
entries
Print
1500 2
250 – ...Error
c
Turn the mode switch
to the MGR position.
250 –
Return the mode switch
to the REG position.
a
57
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 58
OVERLAPPED CASHIER ENTRY
This function allows you to switch from one cashier to another interrupting the first cashier’s entry. The second
cashier can make a sales entry, then the first cashier may continue.
Example
Cashier 1: Entry started
Cashier 2: Cashier change (1 to 2), interruption initiated
Cashier 2: Transaction finished (2)
Cashier 1: Cashier change (2 to 1), entry restart
Note
• The overlapped cashier entry is not available while the tendering sale.
• If any cashier is still making an entry (or has not finalized the transaction yet), the machine does
not run in any mode other than REG and MGR and X/Z reports can not be performed. The error
message “CASHIER ERR.” and the corresponding cashier code(s) are displayed at this time.
Key operation
Comments
The entry by cashier 1 is started.
1. Cashier 1 is assigned.
(1‹)
100 1
360 3
3
2. Cashier 2 is assigned.
2‹
[email protected]
150 2
a
The entry by cashier 2 is started.
(The entry by cashier 1 is interrupted.)
The transaction by cashier 2 is finalized.
3. Cashier 1 is assigned.
1‹
100 1
360 3
a
58
The entry by cashier 1 is restarted.
The transaction by cashier 1 is finalized.
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 59
SPECIAL PRINTING FUNCTIONS
1 Copy receipt printing
If your customer wants a receipt after you have finalized a transaction with the receipt ON-OFF function in the
“OFF” status (no receipting), press the q key. This will make a copy receipt. Your register can also print a
copy receipt when the receipt ON-OFF function is in the “ON” status.
Note
Pressing the q key in the OP X/Z mode before registration toggles the status “ON” and “OFF”.
Example
Printing a copy receipt after making the entries shown below with the receipt ON-OFF function
in the “OFF” status
Key operation
Print
850 2
[email protected]
150 1
a
For receipting→
Print on the
journal
q
Print on the
receipt
When the receipt ON-OFF function is in the “ON” status and you press
the q key to make a second copy
When the receipt ON-OFF function is in the “ON” status,
the “ COPY ” symbol will be printed on the receipt.
59
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 60
2 Validation printing function (Slip printer)
Your register can perform validation printing when it is connected with the slip printer. For the details about the
slip printer, contact your authorized SHARP dealer.
1. Set a validation slip to the slip printer.
2. Press the ∏ key. The validation printing will start.
Note
When you make an entry for which compulsory validation printing can be overridden by performing
the following operation. If you need this function, Contact your authorized SHARP dealer.
1.
2.
Move the mode key to the MGR position.
.
∏
3 Printing of the employee’s arrival and departure times (Slip printer)
Your register can print the employee’s arrival and departure time when it is connected with the slip printer.
For the details for connecting a slip printer, please contact your authorized SHARP dealer.
For printing of the arrival and departure times, you must be in the OP X/Z mode.
Printing of arrival time
1
∏
Printing of departure time
2
∏
4 Printing of header and footer graphic logos
As an optional setting, your register can print a graphic logo on the top of each receipt (header graphic logo). If
preset to do so, a graphic logo can be printed on the bottom of each receipt (footer graphic logo) with the job
code #2616. You can also print the graphic logos with the combination of 3-line header logo message or 3-line
footer logo message. Printing only logo messages without the graphic logo is possible. Please consult your
dealer when you want to change the setting.
• Sample receipt with a header graphic logo and a footer graphic logo
Header graphic logo
Footer graphic logo
60
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 61
5 Remote printer send function
This function enables a partial order to be sent to the kitchen for preparation while the remaining order is still
being placed.
Example
Item entry
RP
SEND
Data transfer to the remote printer
Remaining items will be sent to the remote printer when the transaction is finalized.
When this function is used, the subtotal void operation is not allowed.
61
ER-A410/A420(SEC)-2
03.12.22 0:14 PM
Page 62
TIME DISPLAY AND AUTOMATIC
UPDATING OF THE DATE
1 Time display
When you need the time displayed, turn the mode switch to the OP X/Z position after the preceding transaction
or operation is finalized.
You can also display the time by pressing the = key in the REG or MGR mode.
The time display disappears as soon as you press the c key in the REG or MGR mode or begin the
subsequent entry.
Sample display of 10:25 AM
Date
Time
2 Automatic updating of the date
Once the internal clock unit is started at the correct time, it continues to run as long as the built-in battery is
charged, and updates the date (month, day, year) automatically.
62
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 63
FOR THE MANAGER
PRIOR TO PROGRAMMING
1 Programming keyboard layout
When you are in the PGM1 or PGM2 mode, the keyboard layout will be set to one of the programming layouts
as shown below.
For ER-A410
ø
(NUM) (SPACE) CASH
#
@
( )
( )
7
( )
( )
PO
( )
(%)
( )
( )
”
CL
FOR
RECEIPT JOURNAL
8
4
5
2
1
0
9
’
6
:
3
+
#
”
A
=
I
D
<
>
)
Y
V
!
R
?
Z
W
Ç
N
Pt
J
E
(
.
M
H
-
X
U
Q
L
,
;
SBTL
S
£
O
)
&
%
/
G
B
(
P
K
@
C
00
$
F
æ BACK
Æ SPACE
cl
(SHIFT-2) (SHIFT)
(DC)
Ø
CA/AT/NS
T
➞
➞
▲
▲
➞
For ER-A420
!
@
#
$
%
^
L2
DEPT
&
#
1
œ
2
3
4
5
6
7
CR2
85
912
019
+26
Q
AUTO
W
E
R
T
Y
CR1
U
I
4
O11
P18
–25
7
8
9
A
S
D
F
G
H
J
K3
L10
/ 17
=24
4
5
6
Z”
X
C
V
B
N
M2
;
:
1
2
3
(SHIFT) (DC) (SPACE) (SPACE) (SPACE) (SPACE) (SPACE) (SPACE)
,
.
0
00
Î:
Ó:
é:
?
Note
{
}
?34
<41
>48
”
”
Ñ
6
( 13
)
’27
-33
➞
RECEIPT JOURNAL
[
@
BACK
(SPACE
)
]
CL
FOR
SBTL CA/AT
• The programming keyboard sheet is transparent, allowing placement over the standard keyboard
sheet.
• The shaded area contains the character keys which are used for programming characters.
Used to enter the double-size character.
Used to change a lower-case letter/upper-case letter.
cl
Used to select a symbol.
æ
Æ
To enter the letter “ cl cl ”, press
é
cl
æ
Æ
é
To enter the upper-case letter “Æ Æ”, press
To enter the lower-case letter “æ æ”, press

/
: Used to back up the cursor for deleting.
(NUM)
: Used to enter a numeric character.
cl
æ
Æ
Ó
æ
Æ
cl
cl
cl
æ
Æ
æ
Æ
cl
æ
Æ
Ó
: Used to enter a space.
63
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 64
2 How to program alphanumeric characters
You can program alphanumeric characters for departments, PLUs, UPCs, functions, etc. while in the character
entry mode.
There are two ways for programming characters: using character keys on the keyboard and entering character
codes with the numeric keys on the keyboard.
Using character keys on the keyboard
Enter a character according to the position in the programming keyboard layout.
Entering alphanumeric characters
To enter a character, simply press a corresponding character key.
To enter a numeric character, press (NUM) key and enter a number by ten keys (0 – 9).
(NUM) ➞ 135 ➞ (NUM)
[Ex.] Entering the character “135” :
To enter a space, press the / key.
Entering double-size characters
Î
: This key toggles the double-size character mode and normal-size character mode. The default is the
normal-size character mode. The double-size character is displayed with the letter “=” (ex. =S).
[Ex.] To program the name “SHARP” in double size : Î ➞ SHARP ➞ Î
Entering lower-case letters
Ó
: You can enter a lower-case letter by using this key. Press Ó key just before you enter the lower-case
letter. This key also allows you to enter the characters/symbols shown at the upper right of keys.
[Ex.] To program the name “Sharp” : ➞ S ➞ Ó ➞ harp ➞ Ó
Entering symbols shown at the upper left of keys
é:
You can enter symbols by using this key. Press é key just before you enter the symbol.
[Ex.] To program the symbol “ cl cl ” : ➞ é ➞ cl ➞ é ➞ cl
ˆ
“( )”, “( )”, “( )”, “ ( )”, “( )”, “( )”, “( ° )”, and “( )” keys are used only in combination with a character
ˆ
¨
`
´
´´
˜
key. If the combination is unavailable, only a character key is entered. [Ex.] “Å” : ➞ (°) ➞ A
Editing text
You can edit the text you have entered by deleting characters.
 : Backs up the cursor for deleting the character or figure at the left of the cursor.
Entering character codes
Numerals, letters and symbols are programmable by entering the º key and character codes. See the
“Alphanumeric character code table” on the next page. In this way, you can program characters other than the
characters shown in the programming keyboard layout.
XXX ➞ º
Note
XXX: Character code (3 digits)
• Double-size characters can be made by entering the character code 253.
[Ex.] To program the name “SHARP” in double size
253
º
(DC)
64
083
S
º
072
H
º
065
A
º
082
º
R
080
º
P
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 65
Alphanumeric character code table
Code Character
091
Ä
092
Ö
093
Ü
094
^
095
_
096
’
097
a
098
b
099
c
100
d
101
e
102
f
103
g
104
h
105
i
106
j
107
k
108
l
109
m
110
n
111
o
112
p
113
q
114
r
115
s
116
t
117
u
118
v
119
w
120
x
121
y
122
z
123
{
124
|
125
}
126
ß
127
¢
128
!!
129
1
130
2
131
3
132
4
1/2
133
F/T
134
←
135
Code Character
136
→
137
138
139
140
141
F
142
T
↓
143
ç
144
°
145
¿
146
Ù
147
à
148
Æ
149
ø
150
Å
151
152
¤
é
153
è
154
Pt
155
i
156
Ñ
157
ò
158
£
159
¥
160
161
°
162
163
164
.
165
Á
177
Í
178
A
180
a
181
E
182
e
183
I
184
i
185
186
U
u
187
N
188
.
n.
189
190
C
191
S
C
192
.
▲
Code Character
046
.
047
/
048
0
049
1
050
2
051
3
052
4
053
5
054
6
055
7
056
8
057
9
058
:
059
;
060
<
061
=
062
>
063
?
064
@
065
A
066
B
067
C
068
D
069
E
070
F
071
G
072
H
073
I
074
J
075
K
076
L
077
M
078
N
079
O
080
P
081
Q
082
R
083
S
084
T
085
U
086
V
087
W
088
X
089
Y
090
Z
▲
Code Character
001
á
002
â
003
ê
004
î
005
ì
006
í
007
ô
008
ó
009
û
010
ú
011
œ
012
u
´´
013
ú
014
o
´´
015
ó
016
017
018
019
¨
020
021
022
023
024
025
026
027
´´
028
U
029
Ú
´´
030
O
031
Ó
032
(space)
033
!
034
”
035
#
036
$
037
%
038
&
039
’
040
(
041
)
042
043
+
044
,
045
-
Code Character
.
193
.I
194
G
195
S.
196
G
..
197
g
198
K.
199
k.
L
200
l
201
202
Z
203
D
204
d
205
C
206
c
207
P
208
209
e
210
s
211
c
212
z
213
y
214
.
u
215
n
216
217
218
r
219
224
§
225
Ø
226
227
↑
228
]
229
[
230
231
”
ä
232
ö
233
ü
234
æ
235
å
236
É
237
ñ
238
*(DC)
253
✱
✱
(DC) : Double-size character code
: The shaded character cannot be displayed (will be displayed as space).
Note
The character “ !! ” (code: 128) is displayed as “ ! ”.
65
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 66
PROGRAMMING
This chapter illustrates how to program your cash register.
Basic instructions
All the programming items can be programmed by the Job-Code-Based Programming described later.
However, your machine allows you to program some items using the Direct Programming, which does not
require you to enter the job code.
Job-Code-Based Programming
Simplified procedure :
XXX
(Job code)
@
.
Data entry
Ç
Direct Programming
Sample procedure :
Data entry
–
Ç
(Object key)
Preparations for programming
1.
2.
3.
4.
Plug your machine into a standard grounded AC outlet.
Turn the mode switch to the PGM1 or PGM2 position.
To set the mode switch to the PGM1 position, use the manager or submanager key; and to set it to the
PGM2 position, use the manager key.
Check to see whether both journal and receipt rolls are present in the machine. If they are missing, install
journal and receipt paper rolls correctly referring to the procedure in “4. Installing and removing the paper
roll” under “OPERATOR MAINTENANCE”.
Program the necessary items into your machine.
Direct Programming
1 Setting the date and time
Date
PGM 2
Enter the month (one or two digits), day (two digits), and year (four digits : 2000 – 2099) in this sequence.
Procedure
XXXXXXXX
Date (seven or eight digits)
=
Example
Key operation
Print
08262004 =
Date
66
ER-A410/A420(SEC)-3
Time
03.12.22 0:18 PM
Page 67
PGM 2
Set the time using the military time (24-hour) system. For example, when the time is set to 2:30 AM, enter 230;
and when it is set to 2:30 PM, enter 1430. The time will be printed and displayed using a real-time system. Once
you set the time, the internal clock unit will continue to run as long as the built-in battery is alive and update the
date (day, month, year) properly.
Procedure
XXXX
Time (max. four digits)
=
Example
Key operation
Print
1430 =
Time
2 Programming for departments
Your machine is equipped with 20 (ER-A410)/10 (ER-A420) standard departments and a maximum of 99
departments. Your machine allows you to perform the following programming for each department.
Unit price
PGM 1
PGM 2
Procedure
To program any dept.
To program zero
1
Unit price (max. 6 digits)
Dept. code (1 – 99)
à
99
·
Unit price (max. 6 digits)
Ç
ı
To program zero
To program the next sequential dept.
Example
Key operation
Print
1000 1
Ç
Unit price
67
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Functional selection
Page 68
PGM 2
Procedure
To program any dept.
To set all zeros
@
*1 ABCDEFGHIJKLMNOP
Dept. code (1 – 99)
à
1
99
·
*1 ABCDEFGHIJKLMNOP
Ç
@
To set all zeros
To program the next sequential dept.
*1
Item:
A
Group number
B
Commission group number
C
Sign (plus/minus)
Plus
Minus
Ineligible
Eligible
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Non-compulsory
Compulsory
D
Food stamp status
E
Tax 4 status
F
Tax 3 status
G
Tax 2 status
H
Tax 1 status
I
Item validation printing
J
K
Tare table number
Scale entry
L
Registration type
M
Department type
N
Type of unit price entry
O
P
Significant digit for HALO
Number of zeros to follow the significant digit for HALO
Note
68
Selection:
Inhibit
Enable
Compulsory
Normal
SICS (Single Item Cash Sale)
SIF (Single Item Finalization)
Normal department
Hash department
Bottle return department
Inhibit department key
Open only
Preset only
Open and preset
Entry:
0 thru 9
0 thru 9
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1 thru 9
0
1
2
0
1
2
0
1
2
0
1
2
3
1 thru 9
0 thru 7
Group number
You can assign a department to a maximum of nine groups. This programming enables you to take
group sales reports.
Commission group number
A commission group number (0–9, 0: non commission) can be assigned to each department.
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 69
Sign (plus/minus)
• Assign a plus sign to departments for normal sales transactions.
• Assign a minus sign to departments for minus transactions.
Food stamp status
• Assign a food stamp status (food stamp eligible or food stamp ineligible) to each department.
Tax status (taxable 1 thru 4/non-taxable)
• When an entry of a taxable department is made in a transaction, tax is automatically computed
according to the associated tax table or rate.
• Tax 4 is prohibited if you use the food stamp function.
Item validation printing
If item entries must be validated, program corresponding departments for compulsory validation
printing.
Tare table number
Tare table number associated with scale entry (1 thru 9).
Scale entry
Program a department for scale entry when your store requires items to be sold by weight and are
placed on a scale connected to the register.
Registration type
• If an entry of a department programmed for SICS is made first, the sale will be finalized as soon
as the department key is pressed. If the entry is made after entering a department not
programmed for SICS, the sale will not be finalized until the Ç key is pressed.
• Whenever a sale is made to a department programmed for SIF, the sale is finalized as soon as
the department key is pressed.
Department type
You may program each department as one of the following three types.
• Bottle Return (BR)
• Hash department
A hash department is used to enter the amount of a special “sale”, such as a gift certificate sale or
for the receipt of payment for utility bills, theatre tickets, etc., i.e. “non-sales” registrations. Any
amounts entered in this department are not added to the grand total except tax amounts.
• Normal department.
Type of unit price entry
You may select one of the following four types of unit price entry for each department.
• Open and preset
• Preset only
• Open only
• Inhibit department key
HALO (High Amount Lockout)
You can set an upper limit amount (HALO) for each department. The limit is affective for the REG
mode operations and can be overridden in the MGR mode.
• “OP” is the same as O × 10P
For example, presetting 14 ($100.00) here means that amount entries of up to $100.00 are
allowed in the REG mode. When you preset 17, the upper limit amount is 99999.99.
Example
Key operation
Print
1000000100000317 @ 1
Ç
Taxable1
Group no.
HALO
IJKLMN
Commission group no.
69
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 70
3 PLU/UPC programming
Your machine is equipped with 500 standard PLUs/UPCs. Your machine allows you to perform the following
programming for each PLU/UPC.
• In this manual, the word “UPC” represents UPC (Universal Product Code) and the word “EAN”
represents EAN (European Article Number).
• To review the UPC codes available to this register, please refer to the chapter 13 in “Job-CodeBased programming”.
Note
Unit price
PGM 1
PGM 2
Procedure
To program any PLU/UPC
l Ò
Ä
To program zero
Direct PLU key
Unit price 1
(max. 6 digits)
To program zero
ı
PLU/
UPC
PLU code (max. 5 digits)
Unit price 2
(max. 6 digits)
Ç
ı
When the unit price 2 is disabled.
UPC code (6 to 13 digits)
To program for the following PLU/UPC
Example
Key operation
When the price 
level 2 is enabled. 
Print
PLU/
1P
UPC 1000 ı
ı
Ç


Unit price
Functional selection
PGM 2
Procedure
To program any PLU/UPC
Ä
l Ò
Direct PLU key
PLU code (max. 5 digits)
PLU/
UPC
To program zero
*1 ABCDEFGHIJ
@
Ç
To program for the following PLU/UPC
UPC code (6 to 13 digits)
*1 Item:
A
Commission group number
B
Sign (plus/minus)
70
C
Food stamp status
D
Tax 4 status
E
Tax 3 status
F
Tax 2 status
(To be continued on the next page)
Selection:
Plus
Minus
Ineligible
Eligible
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Entry:
0 thru 9
0
1
0
1
0
1
0
1
0
1
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 71
*1 Item:
G
Tax 1 status
Selection:
Non-taxable
Taxable
H
I
Tare table number
Scale entry
J
Type of unit price entry
Note
Inhibit
Enable
Compulsory
Prohibit mode
Open price only
Preset price only
Open price and preset price
Delete mode
Entry:
0
1
1 thru 9
0
1
2
0
1
2
3
4
Commission group number
A commission group number (0–9, 0: non commission) can be assigned to each department.
Sign (plus/minus)
The function of every PLU/UPC varies according to the combination of its sign and the sign of its
associated department as follows:
Sign
Department
+
–
+
–
Function of PLU/UPC
PLU/UPC
+
–
–
+
Serves as a normal plus PLU/UPC
Serves as a normal minus PLU/UPC
Accepts store coupon entries, but not split-pricing entries
Not valid; not accepted
Food stamp status
• Assign a food stamp status (food stamp eligible or food stamp ineligible) to each PLU/UPC.
Tax status (taxable 1 thru 4/non-taxable)
• When an entry of a taxable PLU/UPC is made in a transaction, tax is automatically computed
according to the associated tax table or rate.
• Tax 4 is prohibited if you use the food stamp function.
Tare table number
Tare table number associated with scale entry (1 thru 9).
Scale entry
Program a PLU/UPC for scale entry when your store requires items to be sold by weight and are
placed on a scale connected to the register.
Type of unit price entry
You may select one of the following four types of unit price entry for each PLU/UPC.
• Open price and preset price (for only PLU)
• Preset price only
• Open price only (for only PLU)
• Prohibit mode: Prohibits the entry of any assigned PLU/UPC code.
• Delete mode: Deletes data programmed for each PLU/UPC.
Example
Key operation
Print
PLU/
1P
UPC 0000001003 @
Ç
Taxable1
(HIJ)
Commission
group no.
71
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 72
PLU/UPC assignment to department
PGM 1
PGM 2
Procedure
To program any PLU/UPC
To delete the entered PLU/UPC
Ä
l Ò
v
Direct PLU key
PLU code (max. 5 digits)
à
Department code (1 – 99)
1
PLU/
UPC
Ç
99
·
UPC code (6 to 13 digits)
To program for the following PLU/UPC
Example
Key operation
Print
PLU/
1P
UPC 1
Ç
Dept. code
4 Programming for discount keys (-)
Discount amount
PGM 1
PGM 2
Procedure
To program zero
- ≠
Discount amount (max. 6 digits)
Ç
Example
Key operation
Print
1000 -
Ç
Discount
amount
72
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 73
High amount lockout (HALO), sign (+/-), vendor/store coupon selection,
food stamp status and tax status PGM 2
Procedure
To program zero
*ABCDEFGHI
@
- ≠
Ç
To program any coupon function
* Item:
Selection:
A
Food stamp status
B
Tax 4 status
C
Tax 3 status
D
Tax 2 status
E
Tax 1 status
F
Sign (+/-)
G
Vendor/store coupon selection
H
I
Significant digit for HALO
Number of zeros to follow the significant digit for HALO
Note
Entry:
Ineligible
Eligible
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Plus
Minus
0
1
0
1
0
1
0
1
0
1
0
1
Vendor coupon (subtotal _)
Store coupon (item _)
0
1
1 thru 9
0 thru 7
Tax status (taxable 1 thru 4/non-taxable)
Tax 4 is prohibited if you use the food stamp function.
HALO (High amount lockout)
“HI” is the same as H x 10 I.
For example, presetting 14 ($100.00) here means that amount entries of up to $100.00 are allowed
in the REG mode. When you preset 17, however, the upper limit amount is 99999.99.
When you preset 00, the open amount entry is prohibited.
Example
Key operation
Print
000001013 @ -
Ç
HALO
Subtotal _
73
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 74
5 Programming for percent keys (%)
Percent rate
PGM 1
PGM 2
Procedure
To program zero
*Rate
Ç
% •
* Rate: Percent rate: 0.00 – 100.00
Note
You must use a decimal point key when setting percentage rates that are fractional.
Example
Key operation
Print
10 . 25 %
Ç
Percent
rate
Sign (+/-), %item/%subtotal selection, food stamp status and tax status
PGM 2
Procedure
To program zero
*ABCDEFGHI
@
* Item:
A
Food stamp status
74
B
Tax 4 status
C
Tax 3 status
D
Tax 2 status
E
Tax 1 status
F
Sign (+/-)
G
%item/%subtotal selection
H
I
Always enter 0.
Always enter 0.
% •
Selection:
Ineligible
Eligible
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Plus
Minus
% for subtotal
% for item
Ç
Entry:
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
ER-A410/A420(SEC)-3
Note
03.12.22 0:18 PM
Page 75
Tax status (taxable 1 thru 4/non-taxable)
Tax 4 is prohibited if you use the food stamp function.
Example
Key operation
Print
000001000 @ %
Ç
Subtotal %
6 Programming for conversion keys (ç)
Currency conversion rate
PGM 1
PGM 2
Procedure
To program zero
*Conversion rate
ç #
Ç
* Conversion rate: 0.0000 – 9999.9999
Note
You must use a decimal point key when setting conversion rates that are fractional.
Example
Key operation
Print
1 . 3250 ç
Ç
75
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 76
7 Programming for the r, p, and † keys
High amount lockout (HALO)
PGM 2
The HALO limit effects REG mode operations but can be overridden in the MGR mode.
The HALO limit is represented by two figures as follows:
Procedure
r A
p π
†
or
To program zero
@
AB
Ç
or
“AB” is the same as A × 10B.
A: Significant digit (0 through 9)
B: Number of zeros to follow significant digit: (for RA or PO: 0 thru 9), (for manual tax: 0 thru 7)
Example
Key operation
Print
13 @ r
Ç
8 Programming for the Ç, Å, ', and k keys
High amount lockout (HALO) and functional selection
PGM 2
Procedure
' ,
CHK2
k k
Å
s
To program zero
*ABCDEFGHIJKLMNOPQ
@
(For
76
Ç
key)
Ç
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 77
* Item:
Selection:
Entry:
Non-compulsory
Compulsory
POST-AUTH
DIAL
CREDIT
DEBIT
CHECK
Yes
No
Partial (printing only part of the card number)
Full (printing the entire card number)
Yes
No
Yes
No
0
1
0
1
0
1
2
0
1
0
1
0
1
0
1
0 thru 9
0
1
0
1
0
1
0
1
0
1
0
1
0
0
1
0 thru 9
0 thru 8
A
CAT transaction
B
CAT action
C
CAT type
D
Card number printing
E
Card number print format
F
CAT signature line print
G
CAT expiration printing
H
I
Number of CAT authorization receipt
Bill (slip) printing
J
Footer printing on receipt
K
Non-add code entry
L
Change enable (over tender enable)
M
Validation printing
N
Drawer opening
O
Amount tendered operation
P
Q
Significant digit for HALO
Number of zeros to follow the significant digit for HALO
Note
Non-compulsory
Compulsory
No
Yes
Non-compulsory
Compulsory
Enable
Disable
Non-compulsory
Compulsory
Yes
No
Optional amount tendered for cash or check
Inhibit amount tendered for charge
Compulsory amount tendered
HALO (High amount lockout)
“PQ” is the same as P × 10 Q.
For example, presetting 13 ($10.00) here means that amount entries of up to $10.00 are allowed in
the REG mode. When you preset 18, however, the upper limit amount is 999999.99.
Example
Key operation
Print
00000000000000115 @ *
Ç
HALO
A thru O
77
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 78
9 Programming for the automatic tax calculation function
Your machine has an automatic tax calculation feature which allows you to program four tax tables to avoid
calculating incorrect tax amounts.
Automatic tax calculations require you to program, in addition to the tax table, the tax status of each pertinent
department, PLU, and function key.
The tax table (applicable to the add-on tax)
PGM 2
Sample tax table
New Jersey tax table: 6%
Range of sales amount
Taxes
.00
.01
Minimum breakpoint
.01
T
.11
Q
Maximum breakpoint
A: Difference between the
minimum breakpoint and
the next one (¢)
to
.10
–
to
.22
10 (0.11 - 0.01)
.02
.23
to
.38
12 (0.23 - 0.11)
.03
.39
to
.56
16 (0.39 - 0.23)
.04
.57
to
.72
18 (0.57 - 0.39)
.05
.73
to
.88
16 (0.73 - 0.57)
to
1.10
16 (0.89 - 0.73)
to
1.22
22 (1.11 - 0.89)
.06
.89
.07
1.11
.08
1.23
to
1.38
12 (1.23 - 1.11)
.09
1.39
to
1.56
16 (1.39 - 1.23)
.10
1.57
to
1.72
18 (1.57 - 1.39)
.11
1.73
to
1.88
16 (1.73 - 1.57)
.12
1.89
to
2.10
16 (1.89 - 1.73)
.13
2.11
to
2.22
22 (2.11 - 1.89)
M1
M2
B: Non-cyclic
C: Cyclic-1
D: Cyclic-2
To program a tax table, first make a table like the right table shown above.
From the tax table, calculate the differences between a minimum break point and the next one (A). Then, from
the differences, find irregular cycles (B) and regular cycles (C and D). These cycles will show you the following
items necessary to program the tax table:
T:
Q:
M1:
M2:
M:
78
The tax amount collected on the minimum taxable amount (Q)
The minimum taxable amount
The maximum value of the minimum breakpoint on a regular cycle (C).
We call this point “MAX point.”
The maximum value of the minimum breakpoint on a regular cycle (D).
We call this point “MAX point.”
Range of the minimum breakpoint on a regular cycle: difference between Q and M1 or between M1 and
M2
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 79
Procedure
One- or two-*1
digit number
†
T
max. three
digits
@
@
Q
max. five
digits
@
*2
Rate
max. six digits
(0.0001 - 99.9999%)
@
M
max. four
digits
Minimum breakpoint
max. five digits
@
@
Ç
Repeat until the MAX point is entered.
*1 First figure:
The first figure to be entered depends upon whether the difference between a minimum
breakpoint to be entered and the preceding minimum breakpoint is not less than $1.00 or
more than 99¢. When the difference is not less than $1.00, enter “1,” and when it is not more
than 99¢, enter “0” or nothing.
Second figure: The second figure depends upon whether your tax table is to be programmed as tax table 1,
2, 3 or 4. When your tax table is to be programmed as tax table 1, enter “1”; when it is to be
programmed as tax table 2, enter “2”; when it is to be programmed as tax table 3, enter “3”;
and when it is to be programmed as tax table 4, enter “4”.
*2 If the rate is fractional (e.g. 4-3/8%), then the fractional portion (3/8) would be converted to its decimal
equivalent (i.e. .375) and the resulting rate of 4.375 would be entered. Note that the nominal rate (R) is
generally indicated on the tax table.
Note
If you make an incorrect entry before entering the M in programming a tax table, cancel it with the
Then program
again from the beginning correctly.
c key; and if you make an error after entering the M, cancel it with the ı key.
• Limitations to the entry of minimum breakpoints
Your register can support a tax table consisting of no more than 72 breakpoints. (The number of breakpoints is
36 maximum when the breakpoint difference is $1.00 or more.) If the number of breakpoints exceeds the
register’s table capacity, then the manual entry approach should be used.
Example
Programming the sample tax table shown on the previous page as tax table 1
Key operation
Print
†
Tax rate
M
T
Q
→
→
→
→
The first
cyclic
portion
M1
(MAX point)→
[email protected]
[email protected]
100 @
[email protected]
11 @
23 @
39 @
57 @
73 @
89 @
111 @
a
Note
You do not need to enter the trailing zeros of the tax rate (after the decimal point) but you do need
to enter the decimal point for fractions.
79
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 80
• If the tax is not provided for every cent, modify the tax table by setting the tax for every cent in the
following way.
When setting the tax, consider the minimum breakpoint corresponding to unprovided tax to be the same as the
one corresponding to the tax provided on a large amount.
Sample tax table
Example 8%
Tax
.00
.01
.02
.03
.04
.06
.09
.10
.11
.12
.14
.17
Minimum
breakpoint
.01
.11
.26
.47
.68
.89
1.11
1.26
1.47
1.68
1.89
2.11
Modification of the left tax table
Minimum
breakpoint
Tax
.00
.01
.02
.03
.04
.05
.06
.07
.08
.09
.10
.11
.12
.13
.14
.15
.16
.17
T
.01
.11
.26
.47
.68
.89
.89
1.11
1.11
1.11
1.26
1.47
1.68
1.89
1.89
2.11
2.11
2.11
Q
M1
M2
From the modified tax table above;
Rate = 8(%), T = $0.01 = 1¢, Q = $0.11 = 11¢, M1 = 1.11, M2 = 2.11, M = 100
80
Breakpoint
difference (¢)
1
10 (0.11-0.01)
15 (0.26-0.11)
21 (0.47-0.26)
21 (0.68-0.47)
21 (0.89-0.68)
0 (0.89-0.89)
22 (1.11-0.89)
0 (1.11-1.11)
0 (1.11-1.11)
15 (1.26-1.11)
21 (1.47-1.26)
21 (1.68-1.47)
21 (1.89-1.68)
0 (1.89-1.89)
22 (2.11-1.89)
0 (2.11-2.11)
0 (2.11-2.11)
B: Non-cyclic
C: Cyclic-1
D: Cyclic-2
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 81
Job-Code-Based Programming
This section illustrates how to program items using job codes. Using job codes allows you to program a wide
variety of items in comparison with direct programming.
Start this programming by entering a corresponding job code as shown below.
2110
.
@
All the items which can be programmed by the job-code-based programming are listed on this page and the
following, and those which can also be programmed by the direct programming are marked with the symbol
“ Direct ” that follows job codes.
1 Setting the date and time
Setting the date
PGM 2
2610
Direct
Enter the month (one or two digits), day (two digits), and year (four digits: 2000 – 2099) in this sequence.
Procedure
2610
.
@
Example
Date (seven or eight digits)
Ç
Key operation
Print
2610 . @
08262004 Ç
Date
Setting the time
PGM 2
2611
Direct
Set the time using the military time (24-hour) system. For example, when the time is set to 2:30 AM, enter 230;
and when it is set to 2:30 PM, enter 1430. The time is printed and displayed on the real time system.
Procedure
2611
.
Example
@
Time (max. four digits)
Key operation
Ç
Print
2611 . @
1430 Ç
Time
81
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 82
2 Setting the register and consecutive numbers
Setting the register number
PGM 2
2612
When your store has two or more registers, it is practical to set separate register numbers for their identification.
You may set them with a maximum of six digits.
Procedure
To set the register number “0”
2612
.
Example
@
Register number
(one to six digits)
Ç
To set the register number as “123456”
Key operation
Print
2612 . @
123456 Ç
Register
number
Setting the consecutive number
PGM 2
2613
The consecutive number is increased by one each time a receipt is issued.
Enter a number (one to four digits) that is one less than the desired starting number.
Procedure
To begin the count from 0001
2613
.
Example
@
A number (one to four digits) that is one
less than the desired starting number
Ç
Setting the count start number as “1001”
Key operation
Print
2613 . @
1000 Ç
Consecutive
number
82
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 83
3 Programming for the automatic tax calculation function
Your machine has an automatic tax calculation feature which allows you to program four tax tables or rates to
avoid calculating incorrect tax amounts.
Automatic tax calculations require you to program, in addition to the tax table and rate, the tax status of each
pertinent department, PLU, and function key.
The tax table (applicable to the add-on tax)
PGM 2
2710
Direct
Sample tax table
New Jersey tax table: 6%
Range of sales amount
Taxes
.00
.01
Minimum breakpoint
.01
T
.11
Q
Maximum breakpoint
A: Difference between the
minimum breakpoint and
the next one (¢)
to
.10
–
to
.22
10 (0.11 - 0.01)
.02
.23
to
.38
12 (0.23 - 0.11)
.03
.39
to
.56
16 (0.39 - 0.23)
.04
.57
to
.72
18 (0.57 - 0.39)
.05
.73
to
.88
16 (0.73 - 0.57)
to
1.10
16 (0.89 - 0.73)
to
1.22
22 (1.11 - 0.89)
.06
.89
.07
1.11
.08
1.23
to
1.38
12 (1.23 - 1.11)
.09
1.39
to
1.56
16 (1.39 - 1.23)
.10
1.57
to
1.72
18 (1.57 - 1.39)
.11
1.73
to
1.88
16 (1.73 - 1.57)
.12
1.89
to
2.10
16 (1.89 - 1.73)
.13
2.11
to
2.22
22 (2.11 - 1.89)
M1
M2
B: Non-cyclic
C: Cyclic-1
D: Cyclic-2
To program a tax table, first make a table like the right table shown above.
From the tax table, calculate the differences between a minimum break point and the next one (A). Then, from
the differences, find irregular cycles (B) and regular cycles (C and D). These cycles will show you the following
items necessary to program the tax table:
T:
Q:
M1:
M2:
M:
The tax amount collected on the minimum taxable amount (Q)
The minimum taxable amount
The maximum value of the minimum breakpoint on a regular cycle (C).
We call this point “MAX point.”
The maximum value of the minimum breakpoint on a regular cycle (D).
We call this point “MAX point.”
Range of the minimum breakpoint on a regular cycle: difference between Q and M1 or between M1 and
M2
83
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 84
Procedure
T
max. three
digits
One- or two-*1
digit number
@
.
2710
@
Q
max. five
digits
@
@
@
*2
Rate
max. six digits
(0.0001 - 99.9999%)
Minimum breakpoint
max. five digits
@
M
max. four
digits
@
Ç
Repeat until the MAX point is entered.
*1 First figure:
The first figure to be entered depends upon whether the difference between a minimum
breakpoint to be entered and the preceding minimum breakpoint is not less than $1.00 or
more than 99¢. When the difference is not less than $1.00, enter “1,” and when it is not more
than 99¢, enter “0” or nothing.
Second figure: The second figure depends upon whether your tax table is to be programmed as tax table 1,
2, 3 or 4. When your tax table is to be programmed as tax table 1, enter “1”; when it is to be
programmed as tax table 2, enter “2”; when it is to be programmed as tax table 3, enter “3”;
and when it is to be programmed as tax table 4, enter “4”.
*2 If the rate is fractional (e.g. 4-3/8%), then the fractional portion (3/8) would be converted to its decimal
equivalent (i.e. .375) and the resulting rate of 4.375 would be entered. Note that the nominal rate (R) is
generally indicated on the tax table.
Note
If you make an incorrect entry before entering the M in programming a tax table, cancel it with the
Then program
again from the beginning correctly.
c key; and if you make an error after entering the M, cancel it with the ı key.
• Limitations to the entry of minimum breakpoints
Your register can support a tax table consisting of no more than 72 breakpoints. (The number of breakpoints is
36 maximum when the breakpoint difference is $1.00 or more.) If the number of breakpoints exceeds the
register's table capacity, then the manual entry approach should be used.
Example
Programming the sample tax table shown on the previous page as tax table 1
Key operation
Print
2710 . @
[email protected]
Tax rate →
[email protected]
M
→
100 @
T
→
[email protected]
Q
→
11 @
23 @
The first
39 @
cyclic
57 @
portion
73 @
89 @
M1
(MAX point)→ 111 @
a
Note
84
You do not need to enter the trailing zeros of the tax rate (after the decimal point) but you do need
to enter the decimal point for fractions.
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 85
• If the tax is not provided for every cent, modify the tax table by setting the tax for every cent in the
following way.
When setting the tax, consider the minimum breakpoint corresponding to unprovided tax to be the same as the
one corresponding to the tax provided on a large amount.
Sample tax table
Example 8%
Tax
.00
.01
.02
.03
.04
.06
.09
.10
.11
.12
.14
.17
Modification of the left tax table
Minimum
breakpoint
Minimum
breakpoint
Tax
.01
.11
.26
.47
.68
.89
1.11
1.26
1.47
1.68
1.89
2.11
.00
.01
.02
.03
.04
.05
.06
.07
.08
.09
.10
.11
.12
.13
.14
.15
.16
.17
T
.01
.11
.26
.47
.68
.89
.89
1.11
1.11
1.11
1.26
1.47
1.68
1.89
1.89
2.11
2.11
2.11
Q
M1
M2
Breakpoint
difference (¢)
1
10 (0.11-0.01)
15 (0.26-0.11)
21 (0.47-0.26)
21 (0.68-0.47)
21 (0.89-0.68)
0 (0.89-0.89)
22 (1.11-0.89)
0 (1.11-1.11)
0 (1.11-1.11)
15 (1.26-1.11)
21 (1.47-1.26)
21 (1.68-1.47)
21 (1.89-1.68)
0 (1.89-1.89)
22 (2.11-1.89)
0 (2.11-2.11)
0 (2.11-2.11)
B: Non-cyclic
C: Cyclic-1
D: Cyclic-2
From the modified tax table above;
Rate = 8(%), T = $0.01 = 1¢, Q = $0.11 = 11¢, M1 = 1.11, M2 = 2.11, M = 100
The tax rate
PGM 2
2711
Procedure
2711
.
@
A*
1 to 4
@
When the lowest taxable amount is zero
Tax rate
max. six digits:
0.0001 to
99.9999%
@
Lowest taxable amount
a
max. five digits:
1¢ to $999.99 (Note: A minimum value of 1 must be entered.)
*A: When you program a tax rate as tax rate 1, enter “1”; when you program it as tax rate 2, enter “2”; when you
program it as tax rate 3, enter “3”; and when you program it as tax rate 4, enter “4”.
85
ER-A410/A420(SEC)-3
Example
03.12.22 0:18 PM
Page 86
Programming the tax rate 4% as tax rate 2 with tax exempt as 12¢
Key operation
Print
2711 . @
[email protected]
[email protected]
12 a
Note
• If you make an incorrect entry before pressing the third @ key in programming a tax rate, cancel
it with the c key; and if you make an error after pressing the third @ key, cancel it with the ı
key. Then program again from the beginning correctly.
• You do not need to enter the trailing zeros of the tax rate (after the decimal point), but you do
need to enter the decimal for fractions.
Doughnut tax exempt (for the Canadian tax system)
PGM 2
2715
Procedure
To program zero
2715
Note
.
@
Q’ty for doughnut
tax exempt
(max. 2 digits: 1 to 99)
This option is available only when your register has been set up with the Canadian tax system.
Example
To program the q’ty “6”
Key operation
2715 . @
6a
86
a
Print
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 87
4 Programming for departments
Your machine is equipped with 20 (ER-A410)/10 (ER-A420) standard departments and a maximum of 99
departments. Your machine allows you to perform the following programming for each department.
Functional programming 1
PGM 2
2110
Direct
You can set each department for:
Item validation printing
If item entries must be validated, program corresponding departments for compulsory validation printing.
Tare table number
Tare table number associated with scale entry (1 thru 9)
Scale entry
Program a department for scale entry allowed when your store needs automatic scale entries.
Registration type
• If an entry of a department programmed for SICS is made first, the scale will be finalized as soon as the
department key is pressed. If the entry is made after entering a department not programmed for SICS, the
sale will not be finalized until the Ç key is pressed.
• Whenever a sale is made to a department programmed for SIF, the sale is finalized as soon as the
department key is pressed.
Department type
You may program each department as one of the following three types.
• Bottle Return (BR)
• Hash department
A hash department is used to enter the amount of a special “sale”, such as a gift certificate sale or for the
receipt of payment for utility bills, theatre tickets, etc., i.e. “non-sales” registrations. Any amounts entered in
this department are not added to the grand total except tax amounts.
• Normal department
Note
If your register has been set for “Bottle return and Hash dept.” by your dealer, you cannot program
the department for those operations. So contact your dealer if you need them.
Type of unit price entry
You may select one of the following four types of unit price entry for each department.
• Open and preset
• Preset only
• Open only
• Inhibit department key
87
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 88
Procedure
To program any dept.
To program zero
2110
.
@
@
Dept. code
(1 - 99)
Ç
t
*A B C D E F
To program the next sequential dept.
*1 Item:
A
Selection:
Non-compulsory
Compulsory
Item validation printing
B
C
Tare table number
Scale entry
D
Registration type
E
Department type
F
Type of unit price entry
Example
Inhibit
Enable
Compulsory
Normal
SICS (Single Item Cash Sale)
SIF (Single Item Finalization)
Normal department
Hash department
Bottle return department
Inhibit department key
Open only
Preset only
Open and preset
Programming for department 3
Enter ABCDEF=000003 for department 3.
Key operation
Print
2110 . @
3 @ 000003 t
Ç
A thru F
88
Entry:
0
1
1 thru 9
0
1
2
0
1
2
0
1
2
0
1
2
3
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 89
Functional programming 2
PGM 2
2111
Direct
Sign (plus/minus)
• Assign a plus sign to departments for normal sales transactions.
• Assign a minus sign to departments for minus transactions.
Food stamp status
• Assign a food stamp status (food stamp eligible or food stamp ineligible) to each department.
Tax status (taxable 1 thru 4/non-taxable)
• When an entry of a taxable department is made in a transaction, tax is automatically computed according to
the associated tax table or rate.
Note
Tax 4 is prohibited if you use the food stamp function.
Procedure
To program any dept.
To program zero
2111
@
.
Dept. code
(1 - 99)
@
t
*A B C D E F
Ç
To program the next sequential dept.
* Item:
A
Sign (+/-)
B
Food stamp status
C
Tax 4 status
D
Tax 3 status
E
Tax 2 status
F
Tax 1 status
Example
Selection:
Plus
Minus
Ineligible
Eligible
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Entry:
0
1
0
1
0
1
0
1
0
1
0
1
Programming for department 4 and 10
Enter ABCDEF=010001 for department 4.
Enter ABCDEF=100000 for department 10.
Key operation
Print
2111 . @
4 @ 010001 t
10 @ 100000 t
Ç
Food stamp
eligible and
taxable 1
Minus dept.
89
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 90
A limit amount (HALO) of entry
PGM 2
2112
Direct
You can set amounts (HALO: High Amount Lockout) for each department. The limit is effective for the REG
mode operations and can be overridden in the MGR mode. The HALO limit is represented by two figures as
follows:
Procedure
To program any dept.
To program zero
2112
.
@
@
Dept. code
(1 - 99)
t
*A B
Ç
To program the next sequential dept.
“AB” is the same as A × 10B.
A: Significant digit (0 through 9)
B: Number of zeros to follow significant digit (0 through 7)
For example, presetting 13 ($10.00) here means that amount entries of up to $10.00 are allowed in the REG
mode. When you preset 17, however, the upper limit amount is 99999.99.
Example
Programming HALO limit of 9000.00 (95) for dept. 1
Key operation
Print
2112 . @
1 @ 95 t
Ç
HALO
Alphanumeric characters PGM 2 2114
You can program a maximum of 16 characters (item label) for each department.
Select the characters you want to program, referring to section “2 How to program alphanumeric characters” in
chapter “PRIOR TO PROGRAMMING”.
Procedure
To program any dept.
To keep the current setting
2114
.
@
@
Dept. code
(1 - 99)
Character keys
(max. 16 digits)
t
To program the next sequential dept.
Example
Programming STEAK (steak) for dept. 1
Key operation
Print
2114 . @
1 @ STEAK t
Ç
90
Ç
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Unit price
PGM 1
Page 91
1110
PGM 2
Direct
You can program unit prices up to a maximum of six digits ($9999.99). Even if a department is not programmed
to allow the entry of preset unit prices in functional programming 1 (job #2110), the department is automatically
changed to allow the entry of preset unit prices by this programming entry.
Procedure
To program any dept.
To program zero
1110
.
@
@
Dept. code
(1 - 99)
t
Unit price
(max. 6 digits)
Ç
To program the next sequential dept.
Example
Programming $10.00 for dept. 1
Key operation
Print
1110 . @
1 @ 1000 t
Ç
Commission group assignment
Unit price
PGM 2
2115
Direct
Your machine allows you to assign a commission group (1 – 9) to each department.
Procedure
To program any dept.
To program zero (for no commission)
2115
.
@
@
Dept. code
(1 - 99)
Commission group
(1 - 9)
t
Ç
To program the next sequential dept.
Example
Programming commission group 1 for dept. 1 and commission group 2 for dept. 5
Key operation
Print
2115 . @
[email protected]
[email protected]
Ç
Commission group no.
91
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Group number
PGM 2
Page 92
2116
Direct
You can assign departments to a maximum of 9 groups (1 thru 9).
This programming enables you to take the group department sales reports.
Procedure
To program any dept.
To program zero (for no grouping)
2116
.
@
@
Dept. code
(1 - 99)
t
Group number
(1 - 9)
Ç
To program the next sequential dept.
Example
Programming the group number 1 for dept. 1 and the group number 2 for dept. 2
Key operation
Print
2116 . @
[email protected]
2t
Ç
Group no.
Age limitation
PGM 2
2180
If an item sold is not allowed to be sold to certain aged persons by law, program the age limitation for the
corresponding department.
Procedure
To program any dept.
To program zero (for no limitation)
2180
.
@
@
Dept. code
(1 - 99)
t
Age limitation
(1 - 99)
Ç
To program the next sequential dept.
Note
When a department for which a setting other than zero (1 to 99) has been programmed as the age
limitation is entered, the birthday entry will be enforced.
Example
Programming the age limitation “18” for dept. 2
Key operation
Print
2180 . @
2 @ 18 t
Ç
Age limitation
92
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 93
Print station assignment
2118
PGM 2
When you use a remote printer, please consult your dealer.
Procedure
2118
.
To program zero
@
@
Dept. code
*A B C
Ç
t
To program for the
following dept.
* Item:
A
Remote printer 1 output
B
Remote printer 2 output
C
Printing on the chit receipt
Example
Selection:
Output
Not output
Output
Not output
Yes
No
Entry:
1
0
1
0
1
0
Key operation
Print
2118 . @
9 @ 101 t
Ç
Print station
Department key positioning
PGM 2
2119
You can assign a department code to each key position. Each key position has a corresponding key number.
Departments may be freely selected for the number of department keys and their positions.
To assign the department to a key position, select the key number of the position.
For key number positions, refer to section “3 Standard key number layout” in chapter “KEYBOARD”.
Procedure
To program any key number
Cancellation
2119
.
@
@
Key number
(max. 3 digits)
t
Dept. code
(1 - 99)
Ç
To program the next sequential key number
Note
The key number placement is determined by your local authorized SHARP dealer.
Example
Key operation
Print
2119 . @
[email protected]
2t
Ç
Key no.
93
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 94
5 PLU/UPC programming
Your machine has two kinds of PLU registration methods.
Direct PLU registration: Accomplished by pressing item key (direct PLU key) directly.
Indirect PLU registration: Accomplished by making an entry of PLU code and pressing the PLU/
UPC key.
In this manual, the word “UPC” represents UPC (Universal Product Code) and the word “EAN” represents EAN
(European Article Number).
With regard to the UPC codes available to this register, please refer to the chapter 13 in “Job-Code-Based
programming”.
Each PLU/UPC requires you to program the following:
PLU/UPC code (PLU: max. 5 digits, UPC: 6 to 13 digits)
Associated department
When a PLU/UPC is associated with a department, the following functions of the PLU/UPC depend on the
programming for the corresponding department.
• Type (Bottle return/Hash/Normal)
• Single item cash sale/Single item finalization
• HALO (for “Open” type)
• Item validation print compulsory/non-compulsory
Unit price (max. six digits)
You will usually have unit prices programmed for individual PLUs/UPCs as PLU/UPC unit prices.
If you program unit price “0.00” for a PLU/UPC, you can enter only the selling quantity into the PLU/UPC, i.e.
the PLU/UPC can be used only as a counter.
Base quantity for split-pricing entries – two digits
Program a base quantity for each PLU/UPC dedicated to split-pricing entries.
Type of unit price entry
• If “Preset only” is selected, individual PLU/UPC entries can be made by entering the assigned code and
PLU/
pressing the P
UPC key (or by pressing a direct PLU key without any PLU code entry, or by scanning the UPC
code).
PLU/
• If “Open only” is selected, the P
UPC key must be pressed after the price entry followed by the PLU code and
PLU/
the P
UPC entry (, or the unit price must be entered before pressing a direct PLU key).
• If “Open and preset” is selected, the entries in both “Preset” and “Open” types are available.
• If the delete mode is selected, the corresponding program data for each PLU/UPC is deleted.
• If the prohibit mode is selected, the PLU/UPC code cannot be entered. This mode does not clear the
PLU/UPC program data.
Sign (+/-)
The function of every PLU/UPC varies according to the combination of its sign and its associate
department’s sign as follows:
Sign
Function of PLU/UPC
Dept.
PLU/UPC
+
+
Serves as a normal plus PLU/UPC
–
–
Serves as a normal minus PLU/UPC
+
–
Accepts store coupon entries, but not split-pricing entries.
–
+
Not valid; not accepted.
Food stamp status and tax status (taxable 1, 2, 3 and/or 4, non-taxable)
Item label (max. 16 characters)
Tare table number and scale entry
Age limitation
Commission group (1 to 9)
Mix-and-match table (max. 10 tables)
Set PLU (for only PLU)
You can link a maximum of 10 PLUs to a particular PLU.
Link PLU/UPC link
A PLU/UPC is able to link to any other PLU (e.g. bottle deposit). However, the number of links is a
maximum of 5. Even if more than 5 PLUs are linked, the sixth or higher link is not actualized (ignored).
Print station
94
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 95
Delete period for non-accessed UPC codes
Non-PLU code format
PLU level assignment and direct PLU key positioning
Stock quantity
For some items, you can program in two ways: programming an individual PLU code and for a
range of sequential PLU codes. The procedure marked “For each PLU” shows individual PLU
programming. The procedure marked “For a range of PLUs” shows sequential range PLU
programming.
Note
Department assignment
PGM 1
PGM 2
1200
2230
Direct
Procedure
For each PLU/UPC
To program any PLU/UPC
Ä
@
.
1200
UPC code
(6 to 13 digits)
Note
Associated
dept. code
(max. 2 digits)
@
PLU code
(max. 5 digits)
t
Ç
To program for the following PLU/UPC
As soon as the programming is completed for one PLU/UPC, the next code appears in the display.
For a range of PLUs
@
.
2230
Start PLU code
(max. 5 digits)
Example
To apply the current
setting of start PLU code
to PLUs within the range
@
End PLU code
(max. 5 digits)
@
t
Associated
dept. code
(1 - 99)
Ç
Programming for PLU 1 and UPC 5012345678900 for “Associate department 2”
For each PLU/UPC
Key operation
Print
1200 . @
[email protected]
5012345678900 @ 2 t
Dept. code
Ç
Programming the PLU 11 thru 20 for “Associate department 3”
For a range
of PLUs
Key operation
Print
2230 . @
11 @ 20 @
3t
Ç
95
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Unit prices
PGM 1
Page 96
1210
PGM 2
Direct
Procedure
1210
.
@
To program for the following PLU/UPC
To program zero
Ä
@
PLU code
(max. 5 digits)
UPC code
(6 to 13 digits)
To program zero
t
Unit price 1
(max. 6 digits)
Unit price 2
(max. 6 digits)
Ç
t
When the unit price 2 is disabled.
To program any PLU/UPC
Note
The preset amount will work as the unit price for the “Preset” type and as the HALO amount for the
“Open” type. In the case of the “Open” type, zero preset prevents amount entry and a 9999.99
preset is the maximum limitation. In the case of the “Preset” type zero and 9999.99 preset have no
special meaning. (i.e. 0 amount preset is available.)
Example
Programming “$1.25” for PLU 1
Key operation
When the price 
level 2 is enabled. 


Base quantity
PGM 1
Print
1210 . @
1 @ 125 t
t
Ç
PGM 2
1211
Unit price
Direct
Procedure
To program any PLU/UPC
Ä
1211
.
Example
@
@
PLU code
(max. 5 digits)
UPC code
(6 to 13 digits)
To program zero
t
Base q’ty
(max. 2 digits)
Ç
To program for the following PLU/UPC
Programming “12” for PLU 2
Key operation
Print
1211 . @
2 @ 12 t
Ç
96
Base q’ty
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 97
Type of unit price entry, delete method, tare table no. and scale entry
2210
2231
PGM 2
Direct
Procedure
To program any PLU/UPC
For each PLU/UPC
2210
Ä
@
.
To program zero
@
PLU code
(max. 5 digits)
UPC code
(6 to 13 digits)
t
*A B C D
Ç
To program for the following PLU/UPC
For a range of PLUs
@
.
2231
Start PLU code
(max. 5 digits)
To apply the current
setting of start PLU code
to PLUs within the range
@
End PLU code
(max. 5 digits)
* Item:
A
Delete method (for only UPC)
(for PLU: fixed 1)
B
C
Tare table number
Scale entry
D
Type of unit price entry
Example
@
t
*ABCD
Selection:
Inhibit to delete in non-accessed
UPC deleting job (#105 in Z1 mode)
Delete in non-accessed UPC
deleting job (#105 in Z1 mode)
Inhibit
Enable
Compulsory
Prohibit mode
Open price only (for only PLU)
Preset price only
Open price and preset price (for only PLU)
Delete mode
Ç
Entry:
1
0
1 thru 9
0
1
2
0
1
2
3
4
To program BCD=003 for PLU1
For each PLU/UPC
Key operation
Print
2210 . @
1 @ 003 t
Ç
A thru D
Programming the PLU 11 thru 20 for “Open and preset price”
For a range
of PLUs
Key operation
Print
2231 . @
11 @ 20 @
003 t
Ç
97
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 98
Sign (+/-), food stamp status, and tax status
PGM 2
2211
2232
Direct
Procedure
To program any PLU/UPC
For each PLU/UPC
Ä
@
.
2211
To program zero
@
PLU code
(max. 5 digits)
UPC code
(6 to 13 digits)
t
*A B C D E F
Ç
To program for the following PLU/UPC
For a range of PLUs
@
.
2232
Start PLU code
(max. 5 digits)
To apply the current
setting of start PLU code
to PLUs within the range
@
* Item:
A
Sign (+/-)
B
Food stamp status
C
Tax 4 status
D
Tax 3 status
E
Tax 2 status
F
Tax 1 status
Note
@
End PLU code
(max. 5 digits)
Selection:
Plus
Minus
Ineligible
Eligible
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
t
Ç
Entry:
0
1
0
1
0
1
0
1
0
1
0
1
Tax status (taxable 1 thru 4/non-taxable)
Tax 4 is prohibited if you use the food stamp function.
A PLU/UPC not programmed for Tax 1 thru Tax 4 statuses is registered depending on the tax
status of the department which the PLU/UPC belongs to.
Example
Programming ABCDEF=000001 for PLU 1 and ABCDEF=010000 for PLU 2
For each PLU/UPC
Key operation
Print
2211 . @
1 @ 000001 t
010000 t
Ç
Taxable 1
Food stamp
eligible
98
*ABCDEF
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 99
Programming the range PLU 11 thru 20 for ABCDEF=000001
For a range
of PLUs
Key operation
Print
2232 . @
11 @ 20 @
000001 t
Ç
Alphanumeric characters
PGM 2
2214
You can program a maximum of 16 characters (item label) for each PLU/UPC.
Select the characters you want to program, referring to section “2 How to program alphanumeric characters” in
chapter “PRIOR TO PROGRAMMING”.
Procedure
To program any PLU/UPC
Ä
2214
.
@
PLU code
(max. 5 digits)
@
UPC code
(6 to 13 digits)
Example
To keep the current setting
Character keys
(max. 16 digits)
t
Ç
To program for the following PLU/UPC
Programming MILK (milk) for PLU 1
Key operation
Print
2214 . @
1 @ MILK t
Ç
99
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 100
Assigning of PLUs/UPCs to commission groups
2215
PGM 2
2235
Direct
You can assign PLUs/UPCs to commission groups.
Procedure
For each PLU/UPC
To program any PLU/UPC
Ä
2215
@
.
To program zero (for no commission)
@
PLU code
(max. 5 digits)
UPC code
(6 to 13 digits)
Ç
t
Commission group
(1 - 9)
To program for the following PLU/UPC
For a range of PLUs
@
.
2235
Start PLU code
(max. 5 digits)
Example
To apply the current
setting of start PLU code
to PLUs within the range
@
End PLU code
(max. 5 digits)
@
t
Commission
group
(1 - 9)
Ç
Programming the commission group 1 for PLU 1
For each PLU/UPC
Key operation
Print
2215 . @
[email protected]
Ç
Commission group no.
Programming all of PLU 11 thru 20 for the commission group 1
For a range
of PLUs
Key operation
Print
2235 . @
11 @ 20 @
1t
Ç
100
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Age limitation
PGM 1
Page 101
PGM 2
2280
2236
If an item sold is not allowed to be sold to certain aged persons by law, program the age limitation for the
corresponding PLU/UPC.
Procedure
For each PLU/UPC
To program any PLU/UPC
Ä
@
.
2280
To program zero (for no limitation)
@
PLU code
(max. 5 digits)
UPC code
(6 to 13 digits)
t
Age limitation
(1 - 99)
Ç
To program for the following PLU/UPC
For a range of PLUs
@
.
2236
Start PLU code
(max. 5 digits)
Note
To apply the current
setting of start PLU code
to PLUs within the range
@
End PLU code
(max. 5 digits)
@
Age limitation
(1 - 99)
t
Ç
When a PLU/UPC for which a setting other than zero (1 to 99) has been programmed as the age
limitation is entered, the birthday entry will be enforced.
Example
Programming the age limitation “18” for PLU 2
For each PLU/UPC
Key operation
Print
2280 . @
2 @ 18 t
Ç
Age limitation
Programming the PLU 11 thru 20 for the age limitation “18”
For a range
of PLUs
Key operation
Print
2236 . @
11 @ 20 @
18 t
Ç
101
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Stock quantity
PGM 1
Page 102
1222
PGM 2
1220
1221
You can assign a stock quantity to each PLU/UPC code. (If you want to control a stock quantity, please consult
your dealer.) When you assign it for the first time, follow the below procedure:
Procedure
To program any PLU/UPC
Ä
1222
.
@
@
PLU code
(max. 5 digits)
UPC code
(6 to 13 digits)
Example
To clear the stock quantity
Ç
t
Stock q’ty
(max. 7 digits)
To program for the following PLU/UPC
To program the stock quantity “10” for PLU 2
Key operation
Print
1222 . @
2 @ 10 t
Ç
Stock q’ty
Note
• If you assign another stock quantity to the PLU/UPC code which you have assigned a stock
quantity to, it will be overridden.
• You must use a decimal point (.) key when setting quantities that are fractional.
If you need to add or subtract a stock quantity, follow the below procedure:
Procedure
To program any PLU/UPC
Ä
Addition:
1220
Subtraction: 1221
.
@
PLU code
(max. 5 digits)
UPC code
(6 to 13 digits)
@
Stock q’ty
(max. 7 digits)
Ç
t
To program for the following PLU/UPC
Adding the stock quantity
Example
To add the stock quantity “4” to the current stock quantity “10” of PLU2
Key operation
Print
1220 . @
[email protected]
Ç
Added stock
q’ty
102
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 103
Subtracting the stock quantity
Example
To subtract the stock quantity “1.5” from the current stock quantity “14” of PLU 2
Key operation
Print
1221 . @
[email protected]
Ç
Subtracted
stock q’ty
Set PLU
PGM 2
2221
Procedure
To program any PLU
Cancellation
t
To repeat up to 10 times
2221
.
@
PLU code
(max. 5 digits)
@
Tied PLU code
(max. 5 digits)
t
t
Ç
To program the next sequential PLU
Note
PLU codes must have already been defined.
You can program a maximum of 15 set PLUs. A set PLU can be tied to a maximum of 10 PLUs.
Example
Programming the set PLU 20 (tied PLUs: PLU 201 and PLU 202)
Key operation
Print
2221 . @
20 @ 201 t
202 t
Ç
Tied PLUs
103
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Mix-and-match table
Page 104
PGM 2
2217
2225
The mix-and-match table consists of the adjustment amount and the matching count for discount (satisfying the
count of entered items). You can program a maximum of 10 mix-and-match tables. One table can be assigned
maximum of 5 kind of items.
[Ex.] Mix-and-match table no. 1: matching count=3, adjustment amount $7.00
Mix-and-match items of table no. 1: Item-A ($2.30), Item-B ($3.10), Item-C ($2.50)
<Sale 1>
Item-A $2.30
Item-A $2.30
Item-B $3.10
Subtotal
(Discount
Total
$7.70
$0.70)
$7.00
<Sale 2>
Item-C $2.50
Item-C $2.50
Item-C $2.50
Subtotal
(Discount
Total
<Sale 3>
Item-A $2.30
Item-B $3.10
Item-C $2.50
$7.50
$0.50)
Subtotal
(Discount
$7.00
Total
$7.90
$0.90)
$7.00
Programming of matching count and adjustment amount
Procedure
To program any other table
Cancellation
2225
.
@
Table no.
(1 - 10)
@
t
*A B C D E F G H
Ç
* AB:
Matching count (1 - 99)
CDEFGH: Adjustment amount (max. 6 digits)
Example
Programming mix-and-match table no.1 (matching count=3, adjustment amount $5.00)
Key operation
Print
2225 . @
1 @ 03000500 t
Ç
Adjustment
amount
Matching count
Assigning items to the mix-and-match tables
To program any PLU/UPC
Procedure
Ä
2217
.
@
PLU code
(max. 5 digits)
@
UPC code
(6 to 13 digits)
Example
To program zero
Table no.
(1 - 10)
t
Ç
To program for the following PLU/UPC
Programming mix-and-match table no.1 for PLU 1
Key operation
Print
2217 . @
[email protected]
Ç
Mix-andmatch
table no.
104
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 105
Print station to PLU/UPC assignment
PGM 2
2218
When you use a remote printer, consult your dealer.
Procedure
Scan UPC code
Ä
2218
.
@
PLU code
(max. 5 digits)
UPC code
(6 to 13 digits)
To program zero
@
t
*A B C
Ç
To program for the following PLU/UPC
To program any PLU/UPC
* Item:
A
Remote printer 1 output
B
Remote printer 2 output
C
Printing on the chit receipt
Note
Selection:
Output
Not output
Output
Not output
Yes
No
Entry:
1
0
1
0
1
0
PLU/UPC code must have been already defined.
Example
Key operation
Print
2218 . @
[email protected]
101 t
Print
station
Ç
Delete period for non-accessed UPC codes
PGM 2
2029
You can delete the UPC codes which have not been accessed during the period you set in this program when
you execute the job #105 in Z1 mode when you set “Delete in non-accessed UPC deleting job” in the UPC
delete method (#2210).
Procedure
2029
.
To program “00”
@
Delete period
(1 to 99 days)
Ç
* When you select “00” for the period, no UPC code is deleted by the non-accessed UPC deleting job.
Example
Key operation
Print
2029 . @
60 Ç
105
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 106
Programming Non-PLU code format
2025
PGM 2
The register allows you to specify the Non-PLU code format (flag code: 2, 02, 20 -29).
The format data is as follows:
C
Flag
(02 or 20-29)
C
2
D
Free format
D
Free format
Flag
Price check digit
Field 1
Field 2
Free format area
Procedure
To delete
*1
2025
.
`
`
Flag code
(max. 2 digits)
*1 Flag code: 2, 02, 20 - 29
*2 Item:
*2
ABCDEF
Selection:
A
B
C
D
Length of field 1 (number of digits)
Length of field 2 (number of digits)
Always enter 0.
Meaning of field 2*3
E
Price check digit used
F
TAB or decimal point of field 2 (0, 1, 2, 3)
ı
c
Entry:
0-9
0-9
0
2
0
1
0
0-3
(Fixed position)
Quantity
Price
Yes
No
*3: When you preset a quantity, the sales amount is calculated as follows: quantity x unit price programmed in
#1210.
Example
P
2 0
Flag
code
C
D
PLU no.
D
Price
Price check digit
(TAB2)
Key operation
Print
2025 . `
20 `
540012 ı
ABCDEF
c
Flag code
106
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Link PLU/UPC link
Page 107
PGM 2
2220
Procedure
To program any PLU/UPC
Cancellation
Ä
2220
.
@
@
PLU code
(max. 5 digits)
t
To repeat up to 5 times
t
t
Linked PLU code
(max. 5 digits)
UPC code
(6 to 13 digits)
Ç
To program for the following PLU/UPC
Note
PLU/UPC codes must have already been defined.
You can program a maximum of 15 link PLUs/UPCs. A link PLU/UPC can be linked to a maximum
of 5 PLUs.
Example
Programming so that PLU 25, 26 and 27 are linked to PLU 21
Key operation
Print
2220 . @
21 @ 25 t
26 t
27 t
Ç
Linked
PLUs
Programming of PLU levels and direct PLU keys
PGM 2
2219
You can assign PLU codes to fixed keys in each PLU level and use those keys as direct PLU key.
For assigning a PLU level, press the l, ¬ or Ò key. For example, if you want to assign PLU level 1 and key
no. 1 to a PLU code, press the l key and enter 1 before entering the PLU code.
For key no. position, refer to section “3 Standard key number layout” in chapter “KEYBOARD”.
Procedure
2219
.
To program any key no.
@
l
¬
Ò
Cancellation
Key no.
(max. 3 digits)
@
PLU code
(max. 5 digits)
t
Ç
To program the next sequential key no.
To keep the current level
Note
The key number placement is determined by your local Authorized SHARP Dealer.
Example
Programming of PLU 1 (level 1) and PLU 65 (level 2) are assigned to key no. 21
Key operation
Print
2219 . @
l 21 @ 1 t
¬ 21 @ 65 t
Ç
Key no.
107
ER-A410/A420(SEC)-3
03.12.22 0:18 PM
Page 108
6 Programming for miscellaneous keys
Only function keys which you have programmed on the keyboard will allow this programming.
Programming the rate (%, ç, commission) and the discount (-)
1310
PGM 2
PGM 1
Direct
You can program percent rates, currency conversion rates, commission rate, and discount amount.
Procedure
1310
@
.
*1
Function no.
@
To program zero
*2
Rate or amount
s
a
To program any function
*1: Function no.
1: For the - key
2: For the – key
3: For the — key
4: For the ≠ key
5: For the % key
6: For the § key
7: For the ¶ key
8: For the • key
71: For the ç key
72: For the " key
73: For the # key
109: For the commission sale 1
110: For the commission sale 2
111: For the commission sale 3
112: For the commission sale 4
113: For the commission sale 5
114: For the commission sale 6
115: For the commission sale 7
116: For the commission sale 8
117: For the commission sale 9
*2: Rate or amount
0 — 999999 (Discount amount)
0.00 — 100.00 (% rate)
0.0000 — 9999.9999 (Currency conversion rate)
0.00 — 999.99 (Commission rate)
Example
Assigning $10.00 to the - key, 10.25% to the % key, and 1.325 to the ç key.
Key operation
Print
1310 . @
1 @ 1000 ı
5 @ 10 . 25 ı
71 @ 1 . 325 ı
a
Discount amount
Percent rate
Conversion rate
Note
108
You must use a decimal point when setting percentage rates that are fractional.
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 109
Currency description text programming (ç)
2334
PGM 2
You can program a maximum of 4 characters for each of the ç thru $ keys.
Procedure
To program any conv. function
To keep the current setting
2334
@
.
*: Function no.
71: For the ç key
72: For the " key
Example
@
*Function no.
Character keys
(max. 4 digits)
t
Ç
73: For the # key
74: For the $ key
Programming “US$” for the " key
Key operation
Print
2334 . @
72 @ / US$ t
Ç
Currency description text
109
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 110
A limit amount (HALO) of entry (-, †, r, p)
2312
PGM 2
Direct
The HALO limit is in effect for the REG-mode operations but can be overridden in the MGR mode. The HALO
limit is represented by two figures as follows:
Procedure
To program zero
2312
@
.
*1
Function no.
@
*2
AB
s
a
To program any function
*1: Function no.
1: For the - key
2: For the – key
3: For the — key
4: For the ≠ key
32: For the † key
64: For the r key
65: For the ® key
66: For the p key
67: For the π key
*2: AB is the same as A x 10B.
A: Significant digit (0 through 9)
B: Number of zeros to follow significant digit
0 through 7 (for the - thru ≠, and † keys)
0 through 8 (for the r, ®, p, and π keys)
For example, presetting 13 ($10.00) here means that amount entries of up to $10.00 are allowed in the REG
mode.
You can set up AB = 17 for no limitation (for the - thru ≠, and † keys).
You can set up AB = 18 for no limitation (for the r, ®, p, and π keys).
Example
Programming 13 for the - key.
Key operation
Print
2312 . @
1 @ 13 ı
a
HALO limit
+/- sign, food stamp status, and tax status (%, -)
PGM 2
2311
Direct
+/- sign:
Programming of the +/- sign assigns the premium or discount function for each key.
Food stamp status: Programming of the food stamp status decides whether a premium or discount should be
dealt with as a food stamp-eligible amount or not.
Tax status:
Programming of the tax status decides whether a premium or discount should be dealt with
as a taxable (taxable 1/2/3/4) or non-taxable amount.
Note
110
Tax 4 is prohibited if you use the food stamp function.
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 111
Procedure
To program any function
To program zero
2311
@
.
*1: Function no.
1: For the - key
2: For the – key
3: For the — key
4: For the ≠ key
*1
Function no.
*2
s
ABCDEF
a
5: For the % key
6: For the § key
7: For the ¶ key
8: For the • key
*2: Item:
A
(+/-) sign
B
Food stamp status
C
Tax 4 status
D
Tax 3 status
E
Tax 2 status
F
Tax 1 status
Example
@
Selection:
Plus
Minus
Ineligible
Eligible
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Non-taxable
Taxable
Entry:
0
1
0
1
0
1
0
1
0
1
0
1
Programming ABCDEF=100001 for the % key and ABCDEF=000000 for the § key
Key operation
Print
2311 . @
5 @ 100001 ı
6 @ 000000 ı
a
Taxable 1
111
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Percent entry type (%)
Page 112
2310
PGM 2
You can program the entry type of rates for percent entries.
Procedure
To program any percent function
To program zero
2310
@
.
*1: Function no.
5: For the % key
6: For the § key
7: For the ¶ key
8: For the • key
Example
*1
Function no.
@
*2
Entry type
s
*2: Entry type
0: Inhibited entry
1: Open rate only
2: Preset rate only
3: Open rate and preset rate
Programming “Preset rate only” for the § key
Key operation
Print
2310 . @
[email protected]ı
a
“Preset rate only”
Item% or subtotal% selection (%)
PGM 2
2315
Direct
Item%: Select this when a percent calculation is desired for the individual department and PLU.
Subtotal%: Select this when a percent calculation is desired for merchandise subtotals.
Procedure
To program any percent function
To program zero
2315
@
.
*1: Function no.
5: For the % key
6: For the § key
7: For the ¶ key
8: For the • key
Example
*1
Function no.
@
*2
A
*2: A
0: Subtotal%
1: Item%
Programming “Item%” for the § key
Key operation
Print
2315 . @
[email protected]ı
a
Item%
112
s
a
a
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 113
Percent rate limitation (%)
PGM 2
2313
You can program the upper limit of percent rates for percent entries.
Percent entries that use the upper limit may be overridden in the MGR mode.
Procedure
To program any percent function
To program zero
2313
@
.
*1: Function no.
5: For the % key
6: For the § key
Note
*1
Function no.
@
*2
Rate
s
a
*2: Rate
0.00 – 100.00 (Entering 0.00 inhibits the
open percent rate entry)
7: For the ¶ key
8: For the • key
The . key is needed only for fractional entry.
Example
Programming the limit to 15.5% for the § key
Key operation
Print
2313 . @
6 @ 15 . 5 ı
a
Limitation
Vendor or store coupon selection (-)
2316
PGM 2
Direct
Vendor coupon: Select this when the coupon is to be applied to the total sales amount.
Store coupon: Select this when the coupon is to be applied to an individual department or PLU.
To program any coupon function
Procedure
To program zero
2316
@
.
*1: Function no.
1: For the - key
2: For the – key
Example
*1
Function no.
3: For the — key
4: For the ≠ key
@
*2
A
s
a
*2: A
0: Vendor coupon (subtotal â)
1: Store coupon (item â)
Programming the “Store coupon” for the – key.
Key operation
Print
2316 . @
[email protected]ı
a
Item â
113
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 114
7 Programming for the a, Å, k,
Functional programming
PGM 2
CHK2
, and ' thru , keys
2320
Direct
You can set each media for:
CAT transaction is compulsory
CAT action (POST-AUTH/DIAL)
CAT type (CREDIT/DEBIT/CHECK)
Card number printing selection
Card number print format (partial/full)
CAT signature line print selection
CAT expiration printing selection
Number of CAT authorization receipts (0 - 9)
Bill (slip) print compulsory
Footer printing on receipt
This programming decides whether or not your machine should print a message at the foot of a receipt when a
specified media key is used.
Non-add code compulsory
You can enforce the non-add code entry when a media entry is accepted.
Change enable (over tender enable)
Either change enable or disable can be selected for a corresponding media key.
Validation printing compulsory
If media entries must be validated, set the corresponding media for compulsory validation print.
Drawer opening
You can program each media key to or not to open the drawer.
Amount tendered compulsory
You may select amount tendered compulsory or optional for the a, Å, k, and CHK2 keys.
You may select amount tendered compulsory or inhibited for the ' thru , keys.
Procedure
To program any media function
To program zero
2320
.
@
*1: Function no.
61: For the a key
62: For the Å key
76: For the ' key
78: For the ) key
114
*1
Function no.
@
80: For the * key
82: For the + key
84: For the , key
86: For the k key
*2
ABCDEFGHIJKLMNO
87: For the CHK2 key
56: For the S key
63: For the f key
159: For the ≥ key
s
a
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 115
*2: Item:
A
CAT transaction
Selection:
Non-compulsory
Compulsory
POST-AUTH
DIAL
CREDIT
DEBIT
CHECK
Yes
No
Partial (printing only part of the card number)
Full (printing the entire card number)
Yes
No
Yes
No
B
CAT action
C
CAT type
D
Card number printing
E
Card number print format
F
CAT signature line print
G
CAT expiration printing
H
I
Number of CAT authorization receipts
Bill (slip) printing
Non-compulsory
Compulsory
Footer printing on receipt
No
Yes
Non-add code entry
Non-compulsory
Compulsory
Change enable (over tender enable)
Enable
Disable
Validation printing
Non-compulsory
Compulsory
Drawer opening
Yes
No
Amount tendered operation
Optional amount tendered for cash or check
Inhibit amount tendered for charge
Compulsory amount tendered
J
K
L
M
N
O
Note
Entry:
0
1
0
1
0
1
2
0
1
0
1
0
1
0
1
0 thru 9
0
1
0
1
0
1
0
1
0
1
0
1
0
0
1
• For the S or ≥ key; always enter 0 as A thru H and J thru O.
• For the f key, always enter 0 as A thru H, K, L, and O.
Example
Programming of the * key for selecting only to have compulsory amount tendered
Key operation
Print
2320 . @
80 @
000000000000001 ı
a
A thru O
115
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Tax delete
Page 116
2326
PGM 2
You can program each media key to delete tax (i.e. tax 1, tax 2, tax 3, tax 4) when it is pressed.
Procedure
To program any media function
To keep the current setting
2326
*1
@
.
*1: Function no.
61: For the a key
62: For the Å key
76: For the ' key
78: For the ) key
80: For the * key
*2
B
Tax 3 calculation status
C
Tax 2 calculation status
D
Tax 1 calculation status
Selection:
calculate tax 4
delete tax 4
calculate tax 3
delete tax 3
calculate tax 2
delete tax 2
calculate tax 1
delete tax 1
a
Entry:
0
1
0
1
0
1
0
1
Programming the * key to delete tax 1
Key operation
Print
2326 . @
80 @ 0001 ı
a
A thru D
116
s
ABCD
82: For the + key
84: For the , key
86: For the k key
87: For the CHK2 key
*2: Item:
A
Tax 4 calculation status
Example
@
Function no.
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 117
High amount lockout (HALO) for check cashing, check change,
and cash in drawer PGM 2 2321
You can program the upper limit amounts for check cashing, check change, and cash in drawer.
Procedure
To program any function
To program zero
2321
@
.
*1
Function no.
*1: Function no.
68: For check cashing
69: For check change
89: For cash in drawer (sentinel)
Example
@
*2
a
s
Limit amount
*2: Limit amount
0 thru 999999.99 (check cashing and check change)
0 thru 9999999.99 (cash in drawer)
Setting the limit to $99.99 for check cashing.
Key operation
Print
2321 . @
68 @ 9999 ı
a
High amount lockout (HALO) of entry for media keys
PGM 2
2322
Direct
The HALO limit is in effect for REG mode operations but can be overridden in the MGR mode. The HALO limit
is represented by two figures as follows:
Procedure
To program any media function
To keep the current setting
2322
@
.
*1: Function no.
61: For the a key
62: For the Å key
76: For the ' key
78: For the ) key
80: For the * key
Example
*1
Function no.
82: For the + key
84: For the , key
86: For the k key
87: For the CHK2 key
@
*2
AB
s
a
*2: AB
A: Significant digit (1 thru 9)
B: Number of zeros to follow significant
digit (0 thru 8)
You can set up AB = 18 for no limitation.
Setting the HALO limit to $1000.00 (15) for the * key
Key operation
Print
2322 . @
80 @ 15 ı
a
HALO
117
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Print station assignment
Page 118
2328
PGM 2
When you use a remote printer, consult your dealer.
Procedure
To program any media function
To program zero
2328
.
@
*1: Function no.
61: For the a key
62: For the Å key
76: For the ' key
78: For the ) key
*1
80: For the * key
82: For the + key
84: For the , key
86: For the k key
*2: Item:
A
Remote printer 1 output
B
Remote printer 2 output
C
Printing on the chit receipt
Example
@
Function no.
ABC
s
a
87: For the CHK2 key
56: For the S key
63: For the f key
159: For the ≥ key
Selection:
Output
Not output
Output
Not output
Yes
No
Entry:
1
0
1
0
1
0
Programming of the * key for selecting “remote printer 1 output/remote printer 2 not
output/printing on chit receipt”
Key operation
Print
2328 . @
80 @
101 ı
a
118
*2
Print station
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 119
8 Programming of function text
Programming
PGM 2
2314
You can program a maximum of 8 characters for each function key and other functions using the table on the
following pages. Select the characters you want to program referring to section “2 How to program alphanumeric
characters” in chapter “PRIOR TO PROGRAMMING”.
Procedure
To program any function
To keep the current setting
2314
.
@
* Function no.
(max. 3 digits)
@
Character keys
(max. 8 digits)
s
a
* Function no.: See “List of function texts” on the following pages.
Example
Programming VISA for * key
Key operation
Print
2314 . @
80 @ VISA / / / ı
a
119
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 120
List of function texts
Function
no.
120
Key or function
In default of
proramming
Function
no.
Key or function
In default of
proramming
Net sales total
(–) 1
(–) 2
(–) 3
(–) 4
%1
%2
%3
%4
NET1
56
Service
10
Net taxable 1 subtotal
TAX1 ST
57
Deposit
DEPOSIT
11
Gross tax 1 total
GRS TAX1
58
Deposit refund
DPST RF
12
Tax 1 total of refund entries
RFD TAX1
59
Customer counter
TRANS CT
13
Net tax 1 total
TAX1
60
Sales total
14
Exempt tax 1
TX1 EXPT
61
Cash
15
Net taxable 2 subtotal
TAX2 ST
62
Cash2
NET3
C ASH
C ASH2
16
Gross tax 2 total
GRS TAX2
63
Food stamp sales
FSSALE
17
Tax 2 total of refund entries
RFD TAX2
64
RA
RA
18
Net tax 2 total
TAX2
65
RA2
RA2
19
Exempt tax 2
TX2 EXPT
66
PO
PO
20
Net taxable 3 subtotal
TAX3 ST
67
PO2
21
Gross tax 3 total
GRS TAX3
68
Check cashing
22
Tax 3 total of refund entries
RFD TAX3
69
Check change
CHK/CG
23
Net tax 3 total
TAX3
70
Food stamp change
FS/CG
24
Exempt tax 3
TX3 EXPT
71
Currency conversion1
CONV 1
25
Net taxable 4 subtotal
TAX4 ST
72
Currency conversion2
CONV 2
26
Gross tax 4 total
GRS TAX4
73
Currency conversion3
CONV 3
27
Tax 4 total of refund entries
RFD TAX4
74
Currency conversion4
CONV 4
28
Net tax 4 total
TAX4
75
Food stamp in drawer
FS/ID
29
Exempt tax 4
TX4 EXPT
76
Gross charge1
CHARGE1
30
Gross manual tax total
GRS MTAX
77
Refund charge1
CHARGE1–
31
Refund manual tax total
RFD MTAX
78
Gross charge2
CHARGE2
32
Net manual tax total
M–TAX
79
Refund charge2
CHARGE2–
*33
Exempt total from GST
GST EXPT
80
Gross charge3
CHARGE3
*34
PST total
PST TTL
81
Refund charge3
CHARGE3–
*35
1
1
2
2
3
3
4
4
5
%1
6
%2
7
%3
8
%4
9
48
Hash item void
HASH VD
49
Hash item refund
HASH RF
50
No sale
NO SALE
51
Validation print counter
VP CNT
52
Bill (slip) counter
BILL CNT
53
Drawer counter
DRW CNT
54
Tray subtotal
TRAY TL
55
PBAL
PBAL
SERVICE
PO2
CA/CHK
GST total
GST TTL
82
Gross charge4
CHARGE4
36
FS1 forgive
FS TX1
83
Refund charge4
CHARGE4–
37
FS2 forgive
FS TX2
84
Gross charge5
CHARGE5
38
FS3 forgive
FS TX3
85
Refund charge5
CHARGE5–
39
Tax total
TTL TAX
86
Check
CHECK1
40
Net
Check2
CHECK2
Sales total including tax total
NET
NET2
87
41
88
Cash + check in drawer
CA/CH ID
42
Coupon-like PLU
CP PLU
89
Cash in drawer
43
Item void
VOID
44
Subtotal void
SBTL VD
91
Sales average
AVE.
45
Manager void
MGR VD
92
Group 1
46
Void mode
VOID
93
Group 2
47
Refund
REFUND
94
Group 3
G ROUP01
G ROUP02
G ROUP03
*90
Exempt VAT
CID
VAT EXPT
ER-A410/A420(SEC)-4
Function
no.
03.12.22 0:20 PM
Key or function
Page 121
In default of
proramming
Function
no.
Key or function
In default of
proramming
134
CCD differ total
135
Subtotal
SUBTOTAL
136
Merchandise subtotal
MDSE ST
137
Total
138
Change
CHANGE
Group 9
G ROUP04
G ROUP05
G ROUP06
G ROUP07
G ROUP08
G ROUP09
139
Food stamp subtotal
FS ST
Price level 1 for PLU
LEVEL 1
140
Food stamp tender
FS TEND
102
Price level 2 for PLU
LEVEL 2
141
Food stamp change
FS CG
103
(+)Dept. total
142
Items
ITEMS
104
(–)Dept. total
143
Copy receipt title
DEPT
105
Hash (+)dept. total
144
Group report title
GROUP
106
Hash (–)dept. total
145
PLU/UPC report title
PLU/UPC
107
(+)Bottle return total
146
Stock report title
STOCK
108
(–)Bottle return total
BTTL(–)
147
Zero sales report title
ZERO SAL
109
Commission sale 1
COM.SAL1
148
Category report title
CATEGORY
110
Commission sale 2
COM.SAL2
149
Transaction report title
TRANS.
111
Commission sale 3
COM.SAL3
150
Cash in drawer report title
CID
112
Commission sale 4
COM.SAL4
151
Commission sales report title SALES
113
Commission sale 5
COM.SAL5
152
CCD report title
CCD
114
Commission sale 6
COM.SAL6
153
Cashier report title
CASHIER
115
Commission sale 7
COM.SAL7
154
Hourly report title
HORLY
116
Commission sale 8
COM.SAL8
155
Daily net report title
DAILY
117
Commission sale 9
COM.SAL9
156
PBLU report title
PBLU
118
Non commission sale
NON COM.
157
Non-add code text
119
Commission amount 1
COM.AMT1
158
Copy receipt title
120
Commission amount 2
COM.AMT2
159
Final (used only for PGM mode) FINAL
121
Commission amount 3
COM.AMT3
160
Balance
122
Commission amount 4
COM.AMT4
161
Slip print message on journal SLIP PR.
123
Commission amount 5
COM.AMT5
162
Slip next page
NEXT P.
124
Commission amount 6
COM.AMT6
163
Balance forward
BAL FWD
125
Commission amount 7
COM.AMT7
164
Tare weight
TARE WT.
126
Commission amount 8
COM.AMT8
165
DUE (text on display)
DUE
127
Commission amount 9
COM.AMT9
166
TAX ST (text on display)
TAX ST
128
Commission amount total
COM.TTL
167
AMOUNT (text on display)
AMOUNT
129
Cash/check is
CA/CH IS
168
WEIGHT (text on display)
WEIGHT
130
Conversion1 is
CONV1 IS
169
Refund type of sales (text on display) RF SALE
131
Conversion2 is
CONV2 IS
170
Vender coupon UPC
132
Conversion3 is
CONV3 IS
171
Non-accessed UPC report title NO ACCES
133
CCD differ
CCD DIF.
172
Price change title
95
Group 4
96
Group 5
97
Group 6
98
Group 7
99
Group 8
100
101
Note
DEPT TL
DEPT(–)
HASH TL
HASH(–)
BTTL TL
DIF. TL
TOTAL
#
COPY
BALANCE
V. CP UPC
PR. CHNG
• The items marked with “ * ” are for Canada only.
• The function no. 90 “Exempt VAT” is only effective for the Canadian tax system (2 GST, VAT
type).
121
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 122
9 Cashier programming
Cashier code
PGM 1
PGM 2
1500
You can assign a cashier code to each cashier. For more details, please contact your local dealer.
Procedure
To program any cashier no.
To program zero
1500
.
@
Cashier no.
(1 - 20)
s
* Cashier code
(1 - 9999)
@
a
* Programming cashier code “0” inhibits entries of the cashier code.
Example
To program 1111 for cashier no.1 and 1014 for cashier no. 4
Key operation
Print
1500 . @
1 @ 1111 ı
4 @ 1014 ı
Cashier
code
a
Cashier name
PGM 1
PGM 2
1514
You can program a maximum of 8 characters (cashier name) for each cashier. Select the characters you want to
program referring to section “2 How to program alphanumeric characters” in chapter “PRIOR TO
PROGRAMMING”.
Procedure
To program any cashier code
To keep the current setting
1514
Note
.
@
Cashier code
(1 - 9999)
@
s
Character keys
(max. 8 digits)
The cashier code must be programmed for the cashier by job #1500 prior to assigning text.
Example
To program "DICK" for cashier code 1111 and “PETER” for cashier code 1014
Key operation
Print
1514 . @
1111 @ DICK ı
1014 @ PETER ı
a
122
a
Cashier name
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 123
Assigning cashiers to drawers
PGM 2
2510
Procedure
To program any cashier code
To program zero
2510
Note
@
.
Cashier code
(1 - 9999)
@
*A
s
a
The cashier code must be programmed for the cashier by job #1500 prior to assigning drawer no.
* Item:
A
Drawer no.
Example
Selection:
Use no drawer
Set the drawer no. 1 or 2
Entry:
0
1 or 2
Assigning cashier code 1111 to drawer no. 1
Key operation
Print
2510 . @
1111 @ 1 ı
a
Drawer no.
10 Programming various functions
Programming for optional feature selection
PGM 2
2616
Your register enables you to select the following options:
OP X/Z mode availability
When a cashier needs to take the cashier X/Z report, he or she will use the OP X/Z mode.
This programming determines whether he or she will be allowed to use this mode.
Note
You can take the cashier X and Z reports in the X1/Z1 mode regardless of the above programming.
Paid-out in the REG mode
Refund type of sale in the REG mode
Refund in the REG mode
Direct void in the REG mode
Indirect void in the REG mode
Subtotal void in the REG mode
Validation printing in a refund entry
First item direct void
PLU level shift mode
• Automatic return mode: This mode automatically shift the PLU level back to level 1 (ordinary level) after a
direct PLU entry.
• Lock shift mode:
This mode holds the current PLU level until making a level shift operation
(pressing a level shift key).
Available mode for PLU level shift
Printing of the number of purchased items
123
Time printing on the receipt/journal
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 124
Journal print form
You may choose either of the following forms.
• Detailed journal print that shows the details of all entries – the same information as printed on the receipt.
• Summary journal print that shows information about all entries other than normal department entries
(entries into “+” departments and their associated “+” PLUs).
Availability of the item validation printing
Validation printing in a discount (â) entry
Zero skip for various reports
Automatic return mode for PLU level
• By one receipt: Returns the PLU level to level 1 after each receipt.
• By one item:
Returns the PLU level to level 1 after each item entry.
Available mode for PLU/UPC price shift
PLU/UPC price shift mode
• Automatic return mode: This mode automatically shifts the price level back to price 1 (ordinary level) after
the entry.
• Lock shift mode:
This mode holds the current price level until making a price shift selection
(pressing the price shift key).
Automatic return mode for PLU/UPC price level
• By one receipt: Returns the price level to price 1 after each receipt.
• By one item:
Returns the price level to price 1 after each item entry.
No sale in REG mode
Finalization when the subtotal amount is zero in the REG mode
Item printing in PBLU transactions on the slip
Usability of the RA entry
Validation printing in a check cashing entry
Validation printing in a RA entry
Validation printing in a PO entry
Birthday date printing for the age limitation
Footer graphic logo printing
Learning function of UPC entry
Price change function in REG mode
Printing of the price shift text on the receipt/journal
Treating the EAN8 code (200XXXXC/D)
Price entry after ISBN/ISSN code entry
To program any function no. (**P: 1-13)
Procedure
To program zero
2616
.
@
** P
(1 - 13)
**P: 1
* Item:
A OP X/Z mode
124
B
Paid-out in REG mode
C
Refund type of sale in the REG mode
D
Refund in the REG mode
E
Direct void in REG mode
F
Indirect void in the REG mode
(To be continued on the next page)
@
*ABCDEFGH
Selection:
Enable
Disable
Enable
Disable
Enable
Disable
Enable
Disable
Enable
Disable
Enable
Disable
s
a
Entry:
0
1
0
1
0
1
0
1
0
1
0
1
ER-A410/A420(SEC)-4
*
03.12.22 0:20 PM
Page 125
Item:
G Subtotal void in REG mode
H
Validation printing in a refund entry
**P: 2
* Item:
A The first item direct void
B
PLU level shift mode
C
Available mode for PLU level shift
D
Printing of the number of purchased items
E
Time printing on the receipt/journal
F
Journal print form
G Availability of the item validation printing
H
Validation printing in a discount (â) entry
**P: 3
* Item:
A Always enter 0.
B Always enter 0.
C Zero skip in cashier report
D
Zero skip in transaction report
E
Zero skip in department report
F
Zero skip in PLU/UPC report
G Zero skip in hourly report
H
Zero skip in daily net report
**P: 4
* Item:
A Always enter 0.
B Always enter 0.
C Always enter 0.
D Always enter 0.
E Always enter 0.
F Always enter 0.
G Always enter 0.
H Automatic return mode for PLU level
Selection:
Enable
Disable
Non-compulsory
Compulsory
Entry:
0
1
0
1
Selection:
Enable
Disable
Automatic return mode
Lock shift mode
REG and MGR modes
MGR mode only
No
Yes
Yes
No
Detailed
Limited
Enable
Disable
Non-compulsory
Compulsory
Entry:
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Selection:
Entry:
0
0
0
1
0
1
0
1
0
1
0
1
0
1
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Selection:
After each item
After each receipt
Entry:
0
0
0
0
0
0
0
0
1
125
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 126
**P: 5
* Item:
A Always enter 0.
B Always enter 0.
C Always enter 0.
D Always enter 0.
E Always enter 0.
F Available mode for PLU/UPC price shift
G PLU/UPC price shift mode
H
Automatic return mode for PLU/UPC price level
Selection:
REG and MGR modes
MGR mode only
Automatic return mode
Lock shift mode
After each item
After each receipt
Entry:
0
0
0
0
0
0
1
0
1
0
1
**P: 6 (ABCDEFGH: Always enter 0.)
**P: 7
* Item:
A Always enter 0.
B Always enter 0.
C No sale in REG mode
D
E
Finalization when the subtotal amount is zero
in the REG mode
Item printing in PBLU transaction on the slip
Selection:
Enable
Disable
Enable
Disable
Yes
No
F Always enter 0.
G Always enter 0.
H Always enter 0.
**P: 8
* Item:
A Always enter 0.
B Always enter 0.
C Always enter 0.
D Usability of the RA entry
E
Validation printing in a check cashing
F
Validation printing in a RA entry
G Validation printing in a PO entry
H
126
Always enter 0.
Selection:
Without limitation
Only for PBLU transaction
Non-compulsorly
Compulsory
Non-compulsorly
Compulsory
Non-compulsorly
Compulsory
Entry:
0
0
0
1
0
1
0
1
0
0
0
Entry:
0
0
0
0
1
0
1
0
1
0
1
0
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 127
**P: 9
*
Item:
A Always enter 0.
B Always enter 0.
C Birthday date printing for the age limitation
D
E
F
G
H
Always enter 0.
Always enter 0.
Always enter 0.
Always enter 0.
Footer graphic logo printing
Selection:
Entry:
0
0
0
1
0
0
0
0
0
1
Yes
No
No
Yes
**P: 10
*
Item:
A and B Always enter 0.
C
Learning function of UPC entry
D to H
Selection:
Entry:
0
0
1
0
Yes
No
(Fixed position)
Always enter 0.
**P: 11 (ABCDEFGH: Always enter 0.)
**P: 12
*
Item:
A to G
H
Selection:
Always enter 0.
Price change function in REG mode
Entry:
0
0
1
Enable
Disable
**P: 13
*
Item:
A to C
D
Selection:
E
F
Always enter 0.
Printing of the price shift text on the
receipt/journal
Always enter 0.
Treating the EAN8 code (200XXXXC/D)
G
H
Always enter 0.
Price entry after ISBN/ISSN code entry
Example
Entry:
0
0
1
0
0
1
0
0
1
Yes
No
Yes
No
Compulsory
Inhibited
Programming to select zero suppression for the cashier report, transaction report, dept.
report, PLU/UPC report and daily net report, and to select non-skip printing for an hourly
report.
Key operation
Print
2616 . @
3 @ 00000010 ı
a
P: 1 thru 13
A thru H
127
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 128
Programming the parameter of the slip printer
PGM 2
2615
Procedure
When A thru F are zeroes
2615
.
@
* ABCDEF
a
* AB: Initial slip feed line (0 to 64)
CD: Slip print max. line no. (0 to 99)
E: Validation printing counter (1 thru 9 times)
To inhibit validation printing, enter 0.
F: Feed lines after printing of a tray subtotal (0 thru 9 lines)
Example
Entering 009910 to ABCDEF
Key operation
Print
2615 . @
009910 a
Setting the time limit for THE TILL TIMERTM
PGM 2
2617
The machine counts the number of times the drawer is left open for longer than a programmed time limit. The
counter will be incremented by one each time a programmed time limit is reached. The time limit for THE TILL
TIMERTM can be preset for 0 to 255 seconds. The count is printed on the general report and cashier report.
Procedure
To program 0
2617
.
Example
@
Time limit
1 to 255 seconds
Setting the time limit as 30 (seconds).
Key operation
2617 . @
30 a
128
a
Print
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Scale tare table
PGM 2
Page 129
2618
The register can be programmed with up to nine tare tables and allows different tares to be assigned to them
(for auto scale entries).
Procedure
To program 0
2618
.
@
@
Table no.
(1 to 9)
Tare weight
(0.01 to 99.99)
s
a
To program any tare table no.
Example
To assign the tare weight 0.20 lbs to tare table no. 1
Key operation
Print
2618 . @
1 @ 20 ı
a
Table no.
Tare weight
129
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 130
Programming of logo messages
2614
PGM 2
Your register can print programmed messages for customers on every receipt. On the standard model, the
ER-A410 prints a graphic logo/the ER-A420 is set to print a header 3-line message on the receipt. (If you want a
graphic logo customerized for your store, please consult your dealer.)
If you want to print logo message, please consult your dealer too. You have five options described below.
Select the characters you want to program, referring to section “2 How to program alphanumeric characters” in
chapter “PRIOR TO PROGRAMMING.”
Procedure
To program any line no.
To keep the current setting
2614
.
@
*Line number
(1 to 6)
@
Character keys
(max. 24 digits)
s
a
* “Header 3-line message” type: 1 to 3
“Footer 3-line message” type : 4 to 6
“Header 6-line message” type: 1 to 6
“Header 3-line and footer 3-line message” type: 1 to 6 (1 to 3 as header, 4 to 6 as footer)
Text 1st line
Graphic logo
Graphic logo
Text 2nd line
Graphic logo
Text 3rd line
Text 1st line
Text 1st line
Text 2nd line
Text 2nd line
Text 3rd line
Text 3rd line
Text 1st line
Text 4th line
Text 2nd line
Text 5th line
Text 3rd line
Text 6th line
Text 4th line
Text 4th line
Text 5th line
Text 5th line
Text 6th line
Graphic logo only
Example
Header 3-line message
Text 6th line
Header 6-line
message
Header 3-line
message and
footer 3-line
messages
To program the following logo message by using 3 lines:
YOUR
STORE
MESSAGE
Key operation
2614 . @
[email protected]///////
ÎYOURÎ
////t
[email protected]//////
ÎSTOREÎ
///t
[email protected]////
ÎMESSAGEÎ
t
Ç
(/:Space key)
130
Footer 3-line
message
Print
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 131
Selection of X1/Z1 and X2/Z2 reports to be printed in the stacked report
sequence PGM 2 2620
Your register is equipped with the stacked report printing function that enables multiple X/Z reports to be printed
in sequence with only a single request.
Procedure
To cancel the stacked report sequence
@
.
2620
For full reporting (non-range report)
*2
@
*1
Job no.
@
Start range
parameter
For individual reporting
*2 End range
parameter
s
a
To program any Job no.
Note
• A maximum of 70 steps are programmable. “1 step” means the memory size used for one norange type job no. The range type job no. needs “8 steps”.
• When the Z of stacked report is initiated, X only reports will be skipped.
Job code numbers to be used are as follows.
*1: Job no.
Report name
Note
*2: Start/End range parameter
00
General
10
Full department
13
Full department group
20
PLU/UPC
*3 Start code/End code (max. 5/13 digits)
24
PLU/UPC stock
*3 Start code/End code (max. 5/13 digits)
27
PLU/UPC zero sales
29
PLU/UPC price category
30
Transaction
31
Cash in drawer
32
Commission sale
50
Full cashier
60
Hourly sales information
70
Daily net report
80
PBLU report
*3 Start price amount/End price amount
*3 Start time/End time (0 thru 2330)
Range report is available
only in the X1 mode.
*3 Start PBLU code/End PBLU code (1 thru 9999)
*3: Both range setting and full setting are allowed.
Example
To print reports 10 and 13 as a stacked report.
Key operation
Print
2620 . @
10 ı
13 ı
a
131
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 132
Setting the time range for hourly reports
PGM 2
2619
You can set the time range for the hourly report.
Procedure
2619
.
When A thru C are all zeros.
@
* ABC
a
*A: Time range
To set the time range to 30 minutes (in the 24-hour system), enter 0.
To set the time range to 60 minutes (in the 24-hour system), enter 1.
BC: Starting time (hour = 00 to 23)
Example
Setting the time range to 60 minutes with the starting time being set at 7:00
Key operation
Print
2619 . @
107 a
Note
To change this setting, an hourly Z report (#160) must be taken prior to the changes.
Programming of power saving mode
PGM 2
2689
Procedure
2689
*
.
@
*ABCD
a
Item:
A
Entering power save mode when time is
displayed.
BCD Time (min.) to entering power save mode
since no operation is made.
Example
Key operation
2689 . @
0030 a
132
Selection:
Enable
Disable
Entry:
0
1
1 through 254 (min.)
(999: The power save mode is inhibited.)
Print
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 133
PBLU code programming
2810
PGM 2
You can specify the range of PBLU codes available for the register.
Procedure
To program only one code
2810
.
Example
@
@
Start code
(1 - 9999)
a
End code
(1 - 9999)
Programming 1 for start code and 1000 for end code
Key operation
Print
2810 . @
[email protected]
1000 a
Functional programming for the printer
PGM 2
2990
You can program the printing density of the receipt/journal printer.
Procedure
To program zero
2990
.
@
* AB
Ç
*AB: Printing density (00 – 99)
00 = 80% for standard density
50 = 90% for standard density
99 = 100% for standard density
Example
Programming “90% for standard density”
Key operation
Print
2990 . @
50 Ç
133
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 134
Programming of error messages
2641
PGM 2
Your register has standard error messages as indicated in the following list. For more information about the
alphanumeric characters programming, see section “2 How to program alphanumeric characters” under the
chapter “PRIOR TO PROGRAMMING”.
Procedure
To program any text no. (1 - 94)
To keep the current setting
2641
.
@
@
* Text no.
(1 - 94)
Character keys
(max. 12 digits)
t
Ç
* Text no.: See “LIST OF ERROR MESSAGES” shown below.
Example
Programming “ENTRY ERROR” for text no. 1
Key operation
Print
2641 . @
[email protected]
ENTRY / ERROR t
Ç
LIST OF ERROR MESSAGES
Text
no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14-19
20
21
22
23-26
27
28-30
31
32
33
34
35
36
37
38
134
Description
Registration error
Misoperation error
Desired code is not
programmed yet.
(Reserved)
Secret code error
Code is not free
Memory is full.
Insert slip paper.
The entered cashier’s code
is not authorized.
Stock is empty.
Compulsory pushing
the subtotal key
Compulsory tendering
Compulsory PBLU entry
(Reserved)
Remote printer off line
(Reserved)
Overlapped cashier error
(Reserved)
Power off
(Reserved)
Compulsory non-add code
The cashier is not assigned.
(Reserved)
Overflow limitation
The open price entry is
inhibited.
The unit price entry is
inhibited.
The direct non-tendering
finalization after previous
tender entry is inhibited.
Read error of scale data
In default of
programming
ENTRY ERROR
MISOPERATION
NO RECORD
SECRET CODE
NOT FREE
MEMORY FULL
INSERT SLIP
NO AUTHORITY
OUT OF STOCK
SBTL COMPUL.
TEND COMPUL.
PB COMPUL.
OFF LINE
Text
no.
39-50
51
52-53
54
55-60
61
62
63
64
65-66
67
68-69
70
71-73
74
75
76
CASHIER ERR.
POWER OFF
77-78
79
80
# COMPULSORY
NOT ASSIGNED
OVER LIMIT.
INH. OPEN PR
81
82-83
84
85
86
INH. UNIT PR
NOT NON-TEND
SCALE ERROR
87
88
89-93
94
Description
(Reserved)
Weight on scale
(Reserved)
Entry of tare weight
(Reserved)
Desired code is not programmed
yet. (learning function)
Enter price and dept. no.
Enter price and dept. no.
Enter dept. no.
(Reserved)
REG buffer is full.
(Reserved)
Price entry at UPC refund
(Reserved)
Non-accessed UPC delete job
(Reserved)
Closing the drawer is
compulsory.
(Reserved)
Reading of undefined vender
coupon UPC
(Reserved)
Message for prompting entry
of secret code
(Reserved)
Data backup send success
Data backup receive success
Data backup communication
error
Backup data format error
Data backup time out error
(Reserved)
Age limitation error
In default of
programming
WEIGHT
ENTR TARE WT
NO RECORD
PRICE → DEPT
PRICE & DEPT
ENTER DEPT#
BUFFER FULL
ENTER PRICE
DELETE
CLOSE DRAWER
OP ENTER
ENTR SECRET#
SEND OK
RECEIVE OK
COM. ERROR
DATA ERROR
TIME OUT
AGE ERROR
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 135
Check validation message
PGM 2
2642
You can program the text (3 lines) to be printed on validation slip. Up to 24 characters can be programmed per
line.
Procedure
To program any line no.
To keep the current setting
2642
.
Example
@
@
Line no.
(1 - 3)
Character keys
(max. 24 digits)
t
Ç
Programming “FOR DEPOSIT ONLY” for the check validation message
Key operation
Print
2642 . @
[email protected]
FOR / DEPOSIT / ONLY t
Ç
Note
The ∏ key must be placed on the keyboard.
Slip printer’s logo message
PGM 2
2643
You can program the text (3 lines) to be printed on slip. Up to 24 characters can be programmed per line.
Procedure
To program any line no.
To keep the current setting
2643
.
Example
@
@
Line no.
(1 - 3)
Character keys
(max. 24 digits)
t
Ç
Programming “TEXT1” for the slip printer’s logo message
Key operation
Print
2643 . @
[email protected]
TEXT1 t
Ç
Note
The Ω key must be placed on the keyboard.
135
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 136
RS-232C channel assignment
PGM 2
2690
Your register is equipped with two RS-232C interfaces. If you use the communication functions, the channel
number of each RS-232C interface must be programmed by using the following procedure.
To activate the communication functions, please consult your dealer.
Procedure
To program any function no. (**P: 1 - 3)
To program zero
2690
.
@
** P
(1 - 3)
@
*ABCD
t
Ç
** P: 1
* Item:
A
Channel no. for the ON-LINE communication
or sending the print data
B
C
Always enter 0.
Channel no. for the scale
D
Channel no. for the coin dispenser
Selection:
Not connected
Standard channel 1
Standard channel 2
Not connected
Standard channel 1
Standard channel 2
Not connected
Standard channel 1
Standard channel 2
Entry:
0
1
2
0
0
1
2
0
1
2
** P: 2
* Item:
A
Channel no. for the barcode reader
B
Channel no. for the remote printer 1
C
Channel no. for the remote printer 2
D
Always enter 0.
Note
Selection:
Not connected
Standard channel 1
Standard channel 2
Not connected
Standard channel 1
Standard channel 2
Not connected
Standard channel 1
Standard channel 2
Entry:
0
1
2
0
1
2
0
1
2
0
For the barcode reader, when you use the model ER-A6HS1, always select the standard channel 1.
** P: 3
* Item:
A
Always enter 0.
B
Channel no. for the slip printer
C
D
Note
136
Always enter 0.
Channel no. for CAT
Selection:
Not connected
Standard channel 1
Standard channel 2
Not connected
Standard channel 1
Standard channel 2
• Never enter any number other than 0, 1 and 2.
• The data backup function always uses standard channel 1.
Entry:
0
0
1
2
0
0
1
2
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Example
Page 137
Assigning channel 1 to the slip printer
Key operation
3
Print
2690 . @
@ 0100 t
Ç
Barcode reader programming
PGM 2
2691
Procedure
To program zero
2691
.
@
* ABCD
* Item:
A
Data bit
B
Parity bit
C
Stop bit
D
Transmission speed
Ç
Selection:
7 bits
8 bits
Non parity
Odd parity
Even parity
1 bit
2 bits
19200 bps
9600 bps
4800 bps
Entry:
1
0
2
1
0
1
0
2
1
0
Example
Key operation
Print
2691 . @
1110 Ç
ABCD
137
ER-A410/A420(SEC)-4
04.1.28 4:10 PM
Page 138
Remote printer programming
PGM 2
2692
Procedure
To program zero
2692
.
@
Remote printer no.
(1 or 2)
* Item:
A
Logo text printing
B
Auto cutter function
C
Type of the printer
@
t
*ABC
Selection:
Not print
Print
Disable
Enable
TM-U200
TM-U230
TM-T88(3)
TM-T88(3)+Logo
Ç
Entry:
0
1
0
1
0
1
2
3
Example
Key operation
Print
2692 . @
1 @ 100 t
Ç
Second remote printer programming
PGM 2
3653
Procedure
To program zero
3653
.
@
Remote printer no.
(1 or 2)
* Item:
A
Second remote printer
@
*A
t
Selection:
Nothing
Remote printer 1
Remote printer 2
Entry:
0
1
2
Example
Key operation
Print
3653 . @
[email protected]
Ç
138
Ç
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 139
Remote printer name programming
PGM 2
3654
Procedure
To program all spaces
3654
.
@
Remote printer no.
(1 or 2)
@
Printer name
(max. 12 characters)
Ç
t
Example
Key operation
Print
3654 . @
1 @ KP1 t
Ç
Printer name
Print format for remote printer
3655
PGM 2
Procedure
To program zero
3655
.
@
Remote printer no.
(1 or 2)
* Item:
A
Taxable status print
B
Q’ty print when q’ty is “1”.
C
Dept./PLU/UPC code print
D
Unit price print
E
Amount print
@
t
*ABCDE
Selection:
Not print
Print
Not print
Print
Not print
Print
Not print
Print
Not print
Print
Ç
Entry:
0
1
0
1
0
1
0
1
0
1
Example
Key operation
Print
3655 . @
1 @ 00000 t
Ç
ABCDE
139
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Chit receipt format
Page 140
PGM 2
3656
Procedure
To program zeros
3656
.
@
*ABCDE
* Item:
A
Taxable status print
B
Q’ty print when q’ty is “1”.
C
Dept./PLU/UPC code print
D
Unit price print
E
Amount print
Ç
Selection:
Not print
Print
Not print
Print
Not print
Print
Not print
Print
Not print
Print
Entry:
0
1
0
1
0
1
0
1
0
1
Example
Key operation
3656 . @
00000 Ç
140
Print
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 141
Programming of RS-232C interface
PGM 2
6110
6111
6112
6113
6115
6220
Online terminal number
Procedure
To program zero
.
6110
@
Ç
Terminal no.
(max. 6 digits)
Transmission line form system
Procedure
To program zero
.
6111
@
* AB
Ç
* Item:
A
Sensing of the CI signal
B
Line form
Selection:
No
Sensing
Full duplex system
Half duplex system
Entry:
0
1
0
1
Selection:
Data download and upload
Print data send
4800 bps
9600 bps
19200 bps
38400 bps
Entry:
0
1
4
5
6
7
Functional programming
Procedure
To program zero
.
6112
@
* AB
Ç
* Item:
A
Selection of print data send/data download and
upload
B
Baud rate (38400/19200/9600/4800 bps)
The selected baud rate is used for on-line
communications and print data sending.
It is not used for the data backup function.
Start code and end code
Procedure
To program zero
6113
.
@
* ABCD E F
Ç
* ABC: Start code (000 – 127)
DEF: End code (000 – 127)
Time out setting
Procedure
6115
.
@
Time out time
(1 – 255 sec)
Ç
141
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 142
Programming for print data sending
Procedure
To program zero
.
6220
@
* ABC
Ç
* Item:
A
Sensing of DR signal
B
Sensing of CS signal
C
Sending of all print data
Selection:
Yes
No
Yes
No
Disable
Enable
Programming the CAT interface
7110
PGM 2
7111
Entry:
0
1
0
1
0
1
7112
7113
7114
7115
Phone number for dial out
Procedure
To keep the current setting
.
7110
@
Ç
* Character keys
(max. 25 digits)
* The valid characters for dialing are “0 – 9”, “W” and “,”.
Password for dial out
Procedure
To program zero
.
7111
@
Ç
* Password
(max. 8 digits)
* The password can be programmed with zero suppression, however it is
used without zero suppression (00000000 - 99999999) for dialing.
Functional programming
Procedure
To program zero
.
7112
@
* ABC
Ç
* Item:
A
PIN PAD on CAT for DEBIT CARD
B
Key type for PIN PAD
C
Dial mode for dial out
Selection:
Yes
No
STATIC
DUKPT
INDEX
Tone
Pulse
Time out setting for time 1 (reading the card)
Procedure
142
7113
To program zero
.
@
Time out time
(1 – 255 sec)
Ç
Entry:
0
1
0
1
2
0
1
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 143
Time out setting for time 2 (response of authorization)
Procedure
To program zero
.
7114
@
Ç
Time out time
(1 – 255 sec)
Time out setting for time 3 (reading of dial in/out)
Procedure
To program zero
.
7115
@
Ç
Time out time
(1 – 3000 sec)
Secret codes to control access to the PGM1 mode, X1/Z1 mode and X2/Z2
2631
2632
mode PGM 2 2630
When a secret code has been set for that specific mode operation, before performing any PGM1 mode, X1/Z1
mode or X2/Z2 mode operation, you must enter a secret code according to the following procedure.
Operating
Procedure
Ç
Note
Secret code
(max. 4 digits)
Ç
Once a secret code is entered, it does not need to be entered again unless the mode switch setting
is changed or an operation is performed.
Programming
Procedure
*
2630
2631
2632
To program zero (no code)
.
@
Secret code
(max. 4 digits)
Ç
* 2630 for the PGM1 mode
2631 for the X1/Z1 mode
2632 for the X2/Z2 mode
Example
Programming secret code 1234 for X1/Z1 mode
Key operation
Print
2631 . @
1234 Ç
143
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 144
Setting the AUTO key — Automatic sequencing key —
X2/Z2
2900
If you program frequently performed transactions or report sequences for the AUTO keys, you can enter those
transactions simply by pressing the corresponding AUTO keys during key operations. This programming can be
done when your machine is in the X2/Z2 mode.
Procedure
Delete
2900
.
Example
@
`
¡
™
£
¢
Transaction
max. 50 times
`
¡
™
£
¢
Ç
Programming for the ` key and ¡ key as follows:
`; entering a $1.50 item (PLU2) and a $1.00 item (dept. 3)
¡; selling a $5.00 -programmed- item (dept. 2) for cash
Key operation
Print
2900 . @
`
AUTO1
setting
AUTO2
setting
Note
144
2 P 100 3
UPC
`
¡
2Ç
¡
Ç
• When the AUTO key has been programmed to execute a report job function etc., the mode switch
must be in the corresponding position.
• The AUTO sequence key can not be preset to another AUTO sequence key.
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 145
11 TRAINING mode
The training mode is used when the operator or the manager practices register operations.
When a training cashier has been selected, the machine automatically enters the training mode. When a
training cashier has not been selected, the register automatically enters the ordinary REG mode. (For
programming of a training cashier, please consult your local dealer.)
The training operations are valid only in REG, MGR, and VOID mode.
The training cashier memory is updated in the training mode. Other memories are not updated.
Example
Key operation
Print
1000 1
[email protected]
Ç
145
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 146
12 Reading stored programs
Your machine allows you to read every program stored in the PGM1 and PGM2 modes.
Program details and procedures for their reading
Program for:
Mode
switch
position
Job
code no.
@
1100
1
Departments
PGM2 or
PGM1
Related job
code nos.
Procedure
For reading all codes
1100
For individual reading
@
Start
dept. code
End
dept. code
Ç
1110, 2110,
2111, 2112,
2114, 2115,
2116, 2180,
2118
@
1200
For reading all codes
For individual reading
Start PLU/
UPC code
2
PLUs/UPCs
PGM2 or
PGM1
1200
@
End PLU/
UPC code
For the last picking list
Scan UPC code
Ç
MDSE
SBTL
Ä
1200, 1210,
1211, 2210,
2211, 2214,
2215, 2230,
2231, 2232,
2235, 2236,
2280, 2218
MDSE
SBTL
PLU/UPC code
To pick up PLU/UPC codes
3
Key nos. for
departments and
PLUs
PGM2
2119
@
2119
4
PGM2
For reading all codes
For individual reading
2220
Start PLU/
UPC code
Set PLUs
PGM2
End PLU/
UPC code
Ç
For reading all codes
2221
2221
For individual reading
Start
PLU code
146
@
2220
@
2221
5
2119, 2219
@
2220
Link PLUs/UPC
link
Ç
@
End
PLU code
Ç
6
Mix-and-match
table
PGM2
2225
2225
@
Ç
2217, 2225
7
UPC’s function
PGM2
2025
2025
@
Ç
2025, 2029
8
Cashiers
PGM2 or
PGM1
1500
1500
@
Ç
1500, 1514,
2510
9
PBLU code
PGM2
2800
2800
@
Ç
2810
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Program for:
10
Function
preset 1
Mode
switch
position
PGM2 or
PGM1
Page 147
Job
code no.
1300
Procedure
1300
@
Ç
Related job
code nos.
1310, 2310,
2311, 2312,
2313, 2314,
2315, 2316,
2320, 2321,
2322, 2326,
2334, 2328
2614, 2615,
2616, 2617,
2618, 2619,
2620, 2630,
2631, 2632,
2689, 2690,
2691, 2692
11
Function
preset 2
PGM2
2600
2600
@
Ç
12
Messages
PGM2
2640
2640
@
Ç
2641, 2642,
2643
13
Tax tables and
rates
PGM2 or
PGM1
2700
2700
@
Ç
2710, 2711,
2715
14
Auto keys
PGM2
2900
2900
@
Ç
2900
15
Thermal printer
PGM2
2990
2990
@
Ç
2990
16
Remote printer
PGM2
3650
3650
@
Ç
3653, 3654,
3655, 3656
17
On-line preset
PGM2 or
PGM1
6110
6110
@
Ç
6110, 6111,
6112, 6113,
6115, 6220
18
CAT preset
PGM2
7110
7110
@
Ç
7110, 7111,
7112, 7113,
7114, 7115
147
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 148
Sample printouts
1 Reading of programmed items for departments
(Reading in the PGM1 and PGM2 modes)
Job code no.
Range
Dept. code
Item label
2 Reading of programmed items for PLUs/UPCs
(Reading in the PGM1 and PGM2 modes)
Mode switch
position*
Mode switch
position*
Range
Unit price
Group no.
PLU code
Tax status
Item label
HALO limit.
Base q’ty
Commission group
Function
programming
00 0 0 0 3
Print station
Tax status
Unit price (level 1)
Unit price (level 2)
Associated
dept. code
Type of unit
price entry
Department type
(BR/Hash/Normal)
Registration type
(SIF/SICS/Normal)
Scale entry
Tare table no.
Item validation
Minus department
1 0 0 3
Type of
unit price
entry
Scale entry
Tare table no.
Delete method
Commission
group and
mix-and-match
table no.
Age limitation
Link PLU
Age limitation
Print station
Set PLU
* When you take this report in the PGM1 mode, the PGM2
indication is replaced by “PGM1”.
148
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 149
3 Reading of programmed key nos. for
departments and PLUs
(Reading in the PGM2 mode)
Key no.
Dept. code
4 Reading of programmed items for link PLUs
(Reading in the PGM2 mode)
Leading
PLU code
Range
Linked
PLU code
5 Reading of programmed set PLUs
(Reading in the PGM2 mode)
PLU code
Tied
PLU code
149
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 150
6 Reading of mix-and-match table
(Reading in the PGM2 mode)
Mix-and-match
table no.
Adjustment amount
8 Reading of programmed items for cashiers
(Reading in the PGM1 and PGM2 modes)
Cashier name
Cashier no.
Mode switch
position*
Cashier code
Drawer no.
Matching count
* When you take this report in the PGM1 mode, the PGM2
indication is replaced by “PGM1”.
7 Reading of programmed UPC’s function
(Reading in the PGM2 mode)
Non-PLU code
format
Delete period for
non-accessed UPC
150
9 Reading of programmed PBLU code
(Reading in the PGM2 modes)
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 151
10 Reading of programmed items for functions - 1
(Reading in the PGM1 and PGM2 modes)
To beyou
continued
thereport
next page
* When
take on
this
in the PGM1 mode,
the PGM2 indication is replaced by “PGM1”.
To be continued on the next page
151
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 152
11 Reading of programmed items for functions - 2
(Reading in the PGM2 mode)
Logo message
Line feed for tray subtotal
Optional feature selection
Drawer open alarm time
Scale tare tables
Hourly report format/start
hour
Stacked report
Secret code
Power saving mode
RS-232C channel data
Barcode reader data
Remote printer data
152
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 153
12 Reading of programmed messages
(Reading in the PGM2 mode)
Error
messages
Check validation
message
Slip printer’s logo
message
To be continued
153
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 154
13 Reading of programmed tax tables and rates
(Reading in the PGM2 mode)
15 Reading of programmed items for the thermal
printer (Reading in the PGM2 mode)
Printing density
Tax rate
Entered Value
Tax table
Printing density
example
Tax rate
Lowest taxable
amount
16 Reading of remote printer preset
(Reading in the PGM2 mode)
14 Reading of programmed items
for auto keys
(Reading in the PGM2 mode)
17 Reading of ON-LINE preset
(Reading in the PGM2 mode)
154
18 Reading of CAT preset
(Reading in the PGM2 mode)
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 155
13 Universal Product Code (UPC) or European Article Number (EAN)
UPC or EAN code
Your machine can support the following codes:
• UPC-A (Number system character: 0, 2, 3, 4)
• UPC-E
• EAN-8
• EAN-13
• Internal code EAN-8/EAN-13
For the codes used in-store marking, there are two types of PLU type (treated as a code like PLU no.) and NonPLU type (price/quantity information is included in the code).
When a code is non-PLU type, the price/quantity in the code is read for sales entry (in case of quantity, “quantity
multiplys preset unit price” is processed to obtain price.)
UPC-A
• Number system character: 0 <used in the source marking>
• Number system character: 3 <used as NDC or HRI>
C
0
Maker code
Check digit
Number system character
For entry, a full 12 digit number or 11 digit number (omitting the
check digits) must be entered.
D
Item code
C
3
D
NCD (or HRI) format
• Number system character: 2 <In-store marking Non-PLU type>
You can program the format by the job #2025.
• Number system character: 4 <In-store marking PLU type>
2
*
Item code
*
*
*
*
C
D
Price
Price check digit
4
For entry, a full 12 digit number, 11 digit number (omitting the
(Free code)
check digit), or a leading zero plus 12 digit number must be
entered.(Any numbers are allowed for the digits marked with *,
and on the receipt/journal, non-PLU type code is printed like 2020008**** (****: price information).)
C
D
UPC-E
• UPC-E is a zero-suppressed version of UPC-A that conforms to
the UPC-E Standards. This code is used for marking small
packages.
For entry, a 6 digit number or a leading zero plus 6 digits number
must be entered.
EAN 8
• Ordinary EAN-8 code (flag: neither 0 nor 2) <used in the source marking>
For entry, a full 8 digit number must be entered.
C
D
Maker code
• Internal code (flag 2) <in-store marking non-PLU short type>
Program the format by the job #2025.
• Internal code (flag 0) <in-store marking PLU short type>
Nation code
Item code
C
2
For entry, a full 8 digit number must be entered. On the
receipt/journal, non-PLU type code is printed like 208**** (****:
price/quantity information)
D
(Free format)
Program the format by the job#2025.
C
0
D
(Free code)
155
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 156
EAN-13
• Ordinary EAN-13 code (used in the source marking)
• Specific EAN-13 code (flag 977, 978, 979) (used in the source
marking: ISBM, ISSN)
C
Maker code
D
Item code
Nation code
For entry, you must enter a full of 13 digits number.
• Internal code (used in the in-store marking, the flag character
number: 20 through 29 and 02)
Program the format by the job# 2025.
C
Flag
02, 20-29
Add-on code
UPC-A and EAN-13 may be followed by a two digits number or a five digits number as add-on code, excepting
UPC-A without a check digit plus two or five digits add-on code.
Therefore, the total number of digits enterable for sales entries are as shown below:
Note
156
D
(Free format)
Program the format by the job #2025.
Code entry
No add-on code
2-digit add-on code
5-digit add-on code
UPC-A
12
14
17
UPC-A w/leading zero
13
15
18
UPC-A w/o check digit
11
–
–
UPC-E
6
–
–
EAN-8
8
–
–
EAN-13
13
15
18
Your register automatically judges the add-on code in an UPC/EAN code entered from the total
number of digits and the flag.
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 157
READING (X) AND RESETTING (Z)
OF SALES TOTALS
• Use the reading function (X) when you need to take a reading of sales information entered since the last
resetting. You can take this reading any number of times. It does not affect the register’s memory.
• Use the resetting function (Z) when you need to clear the register’s memory. Resetting prints all sales
information and clears the entire memory except for the GT1 thru GT3 and training GT, reset count, and
consecutive number.
• If you want to stop the printing report, turn the mode switch to the MGR position. The symbol (“
”) is
printed.
Summary of reading (X) and resetting (Z) reports and the key operations
1 to obtain the reports
X1 and Z1 reports: Daily sales reports
X2 and Z2 reports: Periodic (monthly) consolidation reports
Item
Flash report:
(Only display)
To clear the display,
press the
key
or turn the mode
switch to another
position.
c
Mode switch
position
X1/Z1
X2/Z2
Job
code
Key operation
99 )
1 to ÿ
: Department total amount
Dept. code
à
@ key: Amount of cash in drawer
t key: Paid total
Dept. key (
X1
—
—
X1, Z1
X1, Z1
100
General report
X1, Z1
X2, Z2
200
X1, Z1
151
X2, Z2
Individual cashier
report
251
Reading
100
200
.
@
Reading
151
251
Ç
Resetting
.
For assigned cashier
@
Cashier code
Ç
Resetting
Reading
<OP X/Z> X, Z
51
51
.
@
Ç
@
Ç
Resetting
X1, Z1
Reading
X1, Z1
150
X2, Z2
250
150
250
Full cashier report
Full department
report
X1
X1
X2
110
210
110
210
Individual group
total report on
department
X1
X1
112
X2
212
Full group total
report on
department
X1
X1
113
X2
213
X1, Z1
120
.
Resetting
Ç
112
212
@
@
113
213
@
Ç
Group number
Ç
Reading
X1, Z1
PLU/UPC
report by
designated range
120
220
.
@
Resetting
All PLUs/UPCs
X2, Z2
220
Start PLU/
UPC code
@
End PLU/
UPC code
Ç
157
ER-A410/A420(SEC)-4
Item
03.12.22 0:20 PM
Mode switch
position
X1/Z1
X2/Z2
Page 158
Job
code
Key operation
Reading
X1, Z1
X1, Z1
109
109
209
.
For full reading and resetting
Resetting
For the last picking list
PLU/UPC report
by pick up list
@
X2, Z2
Scan UPC code
Ä
PLU/UPC
code
209
Ç
MDSE
SBTL
MDSE
SBTL
To pick up PLU/UPC codes
PLU/UPC report
by associated
department
X1, Z1
PLU/UPC zero
sales report
X1, Z1
X1, Z1
121
X2, Z2
221
X1, Z1
127
X2
227
X1
129
X1
Reading
121
221
.
@
Ç
Dept. code
Resetting
127
227
@
129
229
@
Ç
PLU/UPC price
category report
All prices
X2
229
124
PLU/UPC stock
report
Ç
End price
amount
@
All PLUs/UPCs
124
X1
@
Start price
amount
Start PLU/
UPC code
@
Ç
End PLU/
UPC code
For full reading
For the last picking list
104
PLU/UPC stock
report by pick up list
X1
104
@
Scan UPC code
PLU/UPC
code
Ç
MDSE
SBTL
Ä
MDSE
SBTL
To pick up PLU/UPC codes
Reading
180
PBLU report
X1, Z1
.
@
Resetting
180
All PBLUs
@
Start
PBLU code
Reading
PBLU report by
cashier
X1, Z1
181
181
.
158
X1
X1
132
X2
232
132
232
@
Ç
For assigned cashier
@
Resetting
Commission sales
report
End
PBLU code
Ç
Cashier code
Ç
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Item
Mode switch
position
X1/Z1
X2/Z2
X1
Page 159
Job
code
X1
130
X2
230
X1
131
X2
231
Transaction report
Cash in drawer
report
X1
Key operation
130
230
@
Ç
131
231
@
Ç
Reading:
160
(For individual
time range)
X1
@
160
Hourly report
@
Start*
time
End*
time
Ç
@
Ç
* Enter the time in the 24-hour system.
Reading
and
Resetting:
X1, Z1
Reading
.
160
Resetting
X1, Z1
X1, Z1
Reading
190
Stacked report
X2, Z2
290
X2, Z2
270
190
290
.
@
Ç
@
Ç
Resetting
When Z of stacked report
is initiated, X only reports
will be skipped.
Reading
Daily net report
270
.
Resetting
Non-accessed UPC deleting
Item
Reading of
non-accessed UPCs
Mode switch
position
X1/Z1
X2/Z2
X1
Job
code
105
Key operation
105
@
Ç
For full deleting
For the last UPC picking list
Deleting of
non-accessed UPCs
Z1
105
105
. @
Scan UPC code
UPC code
MDSE
SBTL
Ç
Ä
MDSE
SBTL
To pick up UPC codes
Note
When you execute the job #105 in Z1 mode, not only the sales data, but also the UPC code(s) (the
related data files) themselves will be deleted.
159
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 160
2 Daily sales totals
General report
You can take X and Z reports in the X1/Z1 mode. The use of the decimal (.) key determines when the report
will actually reset the totals.
• Sample X report
• Sample Z report
Report no.
Read symbol
Reset symbol
Reset counter
Dept. code
Net grand total
(GT2 - GT3)
Grand total of
plus registration
Grand total of
minus registration
Sales q'ty
Sales amount
Grand total of training
mode registration
Ratio of dept. 1
sales amount to
"+" real dept. total
The subsequent printout occurs in the
same format as in the X report.
"+" real dept. counter and total
"-" real dept. counter and total
"+" hash dept.
counter and total
"-" hash dept.
counter and total
To be continued on the next page
Note
160
Not all reports provide the resetting capability. Please refer to the chart on pages 157–159.
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 161
"+" bottle return dept. counter and total
"-" bottle return dept. counter and total
1 counter and total
2 counter and total
Percent 1 counter and total
Percent 2 counter and total
Net sales total
(When the Canadian tax system is selected)
Net taxable 1 total
Gross tax 1 total
Refund tax 1 total
Tax 1
Net tax 1 total
Exempt total from tax 1
Net taxable 3 total
Gross tax 3 total
Refund tax 3 total
Net tax 3 total
Exempt total from tax 3
Gross manual tax total
Refund manual tax total
Net manual tax total
Tax 4
Tax 1 forgiveness total
Tax 2 forgiveness total
Tax 3 forgiveness total
Tax total
Sale total excluding tax
Sales total
including tax
To be continued on the next page
Manual
tax
Exempt
total from
GST
PST total
GST total
161
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 162
3 counter and total
Paid out counter and total
4 counter and total
Paid out 2 counter and total
Percent 3 counter and total
Percent 4 counter and total
Coupon-like PLU counter
and total
Vender coupon UPC
counter and total
Item void counter
and total
Subtotal void counter
and total
Manager item void
counter and total
Check cashing counter and
total
Cash change total for check
and charge 1 - 5 tendering
Cash change total for food
stamp tendering
Currency conversion 1 total
(by programmed rate)
Currency conversion 4 total
(by manual rate)
Food stamp in drawer total
Charge 1 sales and
tendering counter
Charge 1 in drawer
Charge 1 refunds counter
Charge 1 refunds total
Void-mode transaction
counter and total
Refund counter and
total
Hash item void counter
and total
Hash item refund
counter and total
No-sale (exchange) counter
Validation print counter
Bill counter
Drawer counter
Tray subtotal counter
PBAL counter
Service counter
Customer counter
Sales total (including hash
dept. total)
Check sale and tendering
counter
Check in drawer
Cash + check in drawer
Cash in drawer
Cash counter and total
Cash 2 counter and total
Sales for food stamp
counter and total
Received on account
counter and total
Received on account 2
counter and total
162
Deposit counter and total
Deposit refund counter
and total
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 163
Cashier report
Using this function, you can take X and Z reports for individual cashiers or all cashiers.
Individual cashier reading and resetting
The OP X/Z-mode reading and resetting is allowed only when your machine has been programmed
Note
for "OP X/Z mode available" in the PGM2 mode.
• Sample X report
• Sample Z report
Cashier no.
Cashier name
Sales total
Customer counter
The subsequent printout occurs in the
same format as in the sample X report.
Commission 1 sales total
Commission 1 amount
(commission 1 sales
total x commission 1 rate)
Commission amount total
Non-commission sales
total
* When you take these reports in the OP X/Z mode,
the X report shows an “OP X” and the Z report
shows an “OP Z”.
163
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 164
Full cashier reading and resetting
The subsequent printout occurs in the same format as
in the sample report shown in the previous page: and
sales data for cashiers print in this sequence.
164
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 165
Hourly report
You can take X and Z reports for sales totals and transaction (customer) counters for 48 half hours, or 24 hours.
If both quantity and amount are zero, their print is skipped.
• Sample X report
• Sample Z report
The subsequent printout occurs in the
same format as in the sample X report.
Customer counter
Sales total
Average sales amount per customer
(sales total ÷ customer counter)
165
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 166
Full department report
Individual group total report on
department
Sales q'ty and amount
Ratio of dept. 1 sales
amount to "+" real
dept. total
Group 1 total
Full group total report on
department
Group 1 total
166
ER-A410/A420(SEC)-4
03.12.22 0:20 PM
Page 167
PLU/UPC report (by designated range or pick up list)
This function provides you with X and Z reports for sales information of PLUs/UPCs.
You can select either of the designated range operation or pick up list operation. The range may represent all or
part of the PLUs/UPCs in your register.
• Sample X report
• Sample Z report
Range
PLU code
Item label
Sales q’ty and total
(for price level 1)
The subsequent printout occurs in the same
format as in the sample X report.
Sales q’ty and total
(for price level 2)
Note
The PLU/UPC range is not printed in pick up
report (#109).
UPC code
Item label
Range/pick up sum (for price level 1)
Range/pick up sum (for price level 2)
167
ER-A410/A420(SEC)-4
03.12.22 0:21 PM
Page 168
PLU/UPC report by associated department
• Sample X report
• Sample Z report
Associated dept.code
PLU code
Sales q’ty and total
(for price level 1)
The subsequent printout occurs in the same
format as in the sample X report.
PLU/UPC price category report
Price amount
range
Sales q’ty
and total
(for price
level 1)
PLU/UPC zero sales report
PLU code
Item label
168
ER-A410/A420(SEC)-4
03.12.22 0:21 PM
Page 169
PLU/UPC stock report (by
designated range or pick up list)
Commission sales report
Commission 1
(sales total)
Range
Commission 1
(amount)
Current stock
Commission amount
total
Non-commission sales
Net sales total
Note
The PLU/UPC range is not printed in pick
up report (#104).
PBLU report
• Sample X report
• Sample Z report
The subsequent printout occurs in the same
format as in the sample X report.
169
ER-A410/A420(SEC)-4
03.12.22 0:21 PM
Page 170
PBLU report by cashier
• Sample X report
• Sample Z report
The subsequent printout occurs in the same
format as in the sample X report.
Cash in drawer report
You can take full cashier X reports for cash in
drawer.
Transaction report
Cashier
no.
Cashier
name
Customer
counter
Sales total
Cash in
drawer
In this report the same transaction data as those
printed when general reading is taken are printed
except department sales totals.
X1/Z1 stacked report
You can print multiple X1/Z1 reports in sequence at a single time. In this case, you need to program in advance
what X1/Z1 reports should be printed in the stacked report sequence.
Note
170
The following job code numbers (only) can be used for stacked report printing.
Job code number: 100, 110, 113, 120, 124, 127, 129, 130, 131, 132, 150, 160, 180
Refer to “Selection of X1/Z1 and X2/Z2 reports to be printed in the stacked report sequence” for
further details.
ER-A410/A420(SEC)-4
03.12.22 0:21 PM
Page 171
Deleting of non-accessed UPCs
• Sample X report (Reading)
• Sample Z report (Deleting)
UPC code
Item label
The subsequent printout occurs in the same
format as in the sample X report.
Periodic sales*
*: When there is any sales data of the UPC for #209 report, the data in printed here.
When you delete the UPC in Z1 mode under the this situation, the data for #209 is also deleted.
171
ER-A410/A420(SEC)-4
03.12.22 0:21 PM
Page 172
3 Periodic consolidation
Your register allows you to take consolidation X and Z reports of a chosen period (normally one week or a
month).
General Overview
The periodic reading or resetting reports are the same in format as those in the X1/Z1 report for daily total
except job code no. (#2xx) and mode indication (“X2” or “Z2”.)
• Sample X report
• Sample Z report
Reset symbol
Read symbol
Reset counter
of daily total
Reset counter
of periodic
consolidation
Grand total
The subsequent printouts are the same in format as
those in the X/Z report for daily total.
172
ER-A410/A420(SEC)-4
03.12.22 0:21 PM
Page 173
Daily net report
• Sample X report
• Sample Z report
The subsequent printout occurs in the
same format as in the sample X report.
X2/Z2 stacked report
You can print multiple X2/Z2 reports in sequence at a single time. In this case, you need to program in advance
what X2/Z2 reports should be printed in the stacked report sequence.
Note
The following job code numbers (only) can be used for stacked report printing.
Job code number: 200, 210, 213, 220, 227, 229, 230, 231, 232, 250, 270
Refer to “Selection of X1/Z1 and X2/Z2 reports to be printed in the stacked report sequence” for
further details.
173
ER-A410/A420(SEC)-4
03.12.22 0:21 PM
Page 174
COMPULSORY CASH/CHECK
DECLARATION
If you want to make the declaration of the cash and check amount in the drawer mandatory before
performing cashier Z reports, please consult your dealer and have your register programmed for
compulsory cash/check declaration.
If your register is programmed for compulsory cash/check declaration (CCD), a cashier must first count and
declare the cash and check amounts (of domestic and foreign currency) in the drawer, before he or she can
performing a cashier report. The procedure for outputting a CCD report is shown below.
Types of compulsory cash/check declarations
• Compulsory declaration prior to individual cashier resetting
• Compulsory declaration prior to full cashier resetting
• Compulsory cash/check declaration is available in the above two types. You can choose either of
these. Please consult your dealer for further details.
• When the cash/check declaration is compulsory, flash reports are not available.
Note
Key operation
After the Ç key is pressed, the register prompts the cashier to input the cash and check accounts for both
domestic and foreign currency. The cashier can simply input the total amounts of each currency unit, or the
number of bills or coins of each denomination of each currency unit.
• Individual cashier report
OP X/Z mode
51
. @
The drawer opens and the cashier is prompted to
enter the cash and check amounts. (“CCD” is displayed.)
Input the check or
currency denomination
=
ç #
X1/Z1 mode
151
. @
Ç
Q’ty
@
X
v
to
Amount
=
ç #
to
• Full cashier report
X1/Z1 mode
150
. @
Input the total
amount of cash
or check
To cancel
previous
entry
To repeat
t
To display cash/check subtotal
= : When inputting the cash or check amount (domestic currency) in the drawer
ç to # : When inputting the amount of a foreign currency in the drawer
174
Ç
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 175
CCD entry amount
Currency conversion 1 in drawer to be obtained
Total of entered (declared) conversion 1 in drawer
Difference
Check 2 (in domestic currency) in drawer to be obtained
Cash/check in drawer to be obtained
Total of entered (declared) cash/check in drawer
Difference
Total of difference
Cash in drawer to be obtained
175
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 176
OPERATOR MAINTENANCE
1 In case of power failure
When power is lost, the machine retains its memory contents and all information on sales entries.
• When a power failure is encountered in register idle state or during an entry, the machine returns to the normal
state of operation after power recovery.
• When a power failure is encountered during a printing cycle, the register
prints “========” and then carries out the correct printing procedure
after power recovery. (See the sample print.)
2 In case of printer error
If the printer runs out of paper, the printer will hault, “PAPER EMPTY” error will appear on the display, and the
register will start to continuously produce an intermittent beeping tone. Key entries will not be accepted.
Referring to “4. Installing and removing the paper roll” in this chapter, install a new roll paper in the proper
position, then press the c key. The printer will print the power failure symbol and resume printing.
If the print head is up, the printer haults, “HEAD UP” error will appear on the display, and the register will start to
continuously produce an intermittent beeping tone. Key entries will not be accepted. Bring the print head to the
correct position, then press the c key. The printer will print the power failure symbol and resume printing.
3 Thermal printing
Your register prints by means of thermal printing. The print head applies heat to thermal paper which is
chemically treated to change color when heated to a certain level. This creates the printed text.
Cautions in handling the printer
Printing position
Head-up position
176
• If you are not going to use the register for an extended
period of time, pull the print head release lever toward you
so that the print head is set apart from the plate.
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 177
• Avoid the following environments:
Dusty and humid places
Direct sunlight
Iron powder (A permanent magnet and electromagnet are used in this machine.)
• Use the print head release lever only when necessary.
• Never pull the paper when it is in contact with the print head. First release the head with the print head release
lever, and then remove the paper.
• Never touch the surface of the print head.
• Never touch around the print head and the motor during printing or before they have had sufficient time to cool.
Cautions in handling the recording paper (thermal paper)
• Use only the paper specified by SHARP.
• Do not unpack the thermal paper until you are ready to use it.
• Avoid heat. The paper will color at around 70°C.
• Avoid dusty and humid places for storage. Avoid direct sunlight.
• The printed text on the paper can discolor under the following conditions:
Exposure to high humidity and temperature
Exposure to the direct sunlight
Contact with glue, thinner or a freshly copied blueprint
Heat caused by friction from scratching or other such means
Contact with a rubber eraser or adhesive tape
• Be very careful when handling the thermal paper. If you want to keep a permanent record, copy the printed text
with a photocopier.
177
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 178
4 Installing and removing the paper roll
Recording paper specifications
Be sure to use paper rolls specified by SHARP.
The use of any other paper rolls than specified could cause paper jamming, resulting in register malfunction.
Paper specification
Paper width:
1.75 ± 0.02 in. (44.5 ± 0.5 mm)
Max. outside diameter: 3.15 in. (80 mm)
Quality:
Thermal paper
Paper tube:
0.71 in. (18 mm)
• Be sure to set paper roll(s) prior to using your machine, otherwise it may cause a malfunction.
Install the paper roll in the printer. Be careful then to set the roll and cut the paper end correctly.
Note
If the top end of the paper roll is fixed with paste or tape, the paper may lose its color development
ability in the pasted or taped area due to the deterioration of the heat-sensitive color development
component of the paper surface. This may result in nothing appearing at this location when printing
is performed. Therefore, when setting a new paper roll in the machine, be sure to cut off
approximately one revolution (approx. 25 cm long).
(How to set the paper roll)
(How to cut the paper end)
To the printer
To the printer
Incorrect
Correct
Correct
Incorrect
Installing the paper roll
Installing the receipt paper roll
1. Turn the mode switch to the “REG” position with the AC
cord connected.
2. Remove the printer cover.
3. Check that the print head release lever is in its printing
Printing
position
position.
4. Set the paper correctly as illustrated above in the receipt
side of the printer.
5. Insert the end of the paper into the paper chute as shown
on the left. It will automatically be fed through the printer.
6. Cut off the excess paper that comes out of the printer with
the manual cutter.
7. Replace the printer cover.
178
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 179
Installing the journal paper roll
1. Turn the mode switch to the “REG” position with the AC cord
connected.
2. Remove the printer cover.
3. Check that the print head release lever is in its printing
position.
Printing
position
4. Set the paper correctly as illustrated on the previous page in
the journal side of the printer.
5. Insert the end of the paper into the paper chute as shown on
the left. It will automatically be fed through the printer.
6. Insert the end of the paper into the slit in the paper take-up
spool. (Press the Ô key to feed more paper through if
required.)
7. Wind the paper two or three turns around the spool shaft.
8. Set the spool on the bearing.
9. Replace the printer cover.
Note
• When it is difficult to insert paper into the paper chute, try inserting it again by following the steps described
below.
1. Cut off the end of paper in a single straight cut.
2. Pull the print head release lever toward you to lift up the print
head.
Head-up position
3. Insert the end of paper into the paper chute, while pressing
the corresponding paper feed key (Ô key or ‰ key).
4. When the end of paper comes out of the printer, release the
feed key and return the print head release lever to its original
position.
5. Press the feed key to feed more paper.
In case of inserting the journal paper roll
• When you want to manually install a new roll of paper while your machine is turned off, follow the steps shown
below:
1. Pull the print head release lever toward you to lift up the print head.
2. Correctly place the new paper roll into the receipt/journal paper roll location.
3. Insert the paper end into the paper chute until it comes out of the printer.
4. Cut or roll the paper onto the take-up spool as described for automatic installation.
5. Return the print head release lever to its original position.
179
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 180
Removing the paper roll
When a colored dye appears on the paper roll, it is time to replace the existing paper roll. Replace the paper roll
with a new one. If you plan not to use your register for an extended period of time, remove the paper roll, and
store it in the appropriate place.
Removing the receipt paper roll
1. Remove the printer cover.
2. Cut the paper behind the printer and near the paper roll.
3. Press the ‰ key until the paper remaining in the printer
comes out completely.
4. Remove the paper roll from the back of the printer.
Note
Do not pull the paper through the printer.
Removing the journal paper roll
1. Remove the printer cover.
2. Press the Ô key to advance the journal paper until its
Area to cut
printed part is out of the way.
3. Cut the paper and remove the take-up spool.
4. Cut the paper behind the printer and near the paper roll.
5. Press the Ô key until the paper remaining in the printer
comes out completely.
6. Remove the paper roll from the back of the printer.
Note
180
Do not pull the paper through the printer.
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 181
7. Remove the outer side of the take-up spool as shown on the
left.
8. Remove the printed journal roll from the take-up spool.
Removing a paper jam
Precaution: Be very careful with the manual paper cutter, so as not to cut yourself. Never touch the
print head immediately after printing, because the head may still be hot.
1. Remove the printer cover.
2. Pull the print head release lever all the way forward (after it
Pull all the
way forward
stops at one position, continue pulling forward until it stops
again and cannot be pulled forward any further).
3. Remove the paper jam. Check for and remove any shreds of
paper that may remain in the printer.
4. Reset the paper roll correctly by following the steps in
“Installing the paper roll”.
5. Return the print head release lever to its original position.
6. Replace the printer cover.
181
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 182
5 Cleaning the print head
When the printed text is getting dark or faint, paper dust may be stuck to the print head. Clean the print head as
follows:
1. Turn the mode switch to the “OFF” position.
2. Remove the printer cover.
3. Pull the print head release lever all the way forward (after it
Pull all the
way forward
stops at one position, continue pulling forward until it stops
again and cannot be pulled forward any further).
4. Clean the print head with a soft rag moist with ethyl alcohol
or isopropyl alcohol.
5. Return the print head release lever to its original position
immediately after cleaning.
Print head
6. Replace the printer cover.
Caution:
• Never touch the print head with a tool or anything hard
as it may damage the head.
• The paper cutter is mounted on the printer (receipt side).
Be careful not to cut yourself.
182
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 183
6 Removing the till and the drawer
The till in the register is detachable. After closing your business for the day, remove the till from the drawer and
keep the drawer open. To detach the drawer, pull it forward fully with the till removed, and remove it by lifting it
up.
Coin case
Till
Drawer
7 Opening the drawer by hand
The drawer automatically opens normally. However, when power failure is encountered or the machine
becomes out of order, slide the lever located on the machine bottom toward the rear. (See the figure below.)
The drawer will not open if it is locked with a drawer lock key.
Lever
183
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 184
8 Before calling for service
The malfunctions shown in the left-hand column below, labelled “Fault,” do not necessarily indicate functional
faults of the machine. It is therefore advisable to refer to the “Checking” shown in the right-hand column before
calling for service.
Fault
Checking
(1) The display won’t be illuminated even when
the mode switch is turned to any other
position than “OFF”.
(2) The display is illuminated, but the whole machine
refuses registrations.
(3) No receipt is issued.
(4) No journal paper is taken up.
(5) Printing is unusual.
• Is power supplied to the electrical outlet?
• Is the power cord plug out or loosely connected to the
electrical outlet?
• Is a cashier code assigned to the register?
• Is the mode switch set properly at the “REG” position?
• Is the receipt paper roll properly installed?
• Is there a paper jam?
• Is the receipt function in the “OFF” status?
• Is the print head release lever at the printing position?
• Is the take-up spool installed on the bearing properly?
• Is there a paper jam?
• Is the print head release lever at the printing position?
• Is the paper roll properly installed?
Error message table
Text
no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14-19
20
21
22
23-26
27
28-30
31
32
33
34
35
36
37
38
184
Description
Registration error
Misoperation error
Desired code is not
programmed yet.
(Reserved)
Secret code error
Code is not free
Memory is full.
Insert slip paper.
The entered cashier’s code
is not authorized.
Stock is empty.
Compulsory pushing
the subtotal key
Compulsory tendering
Compulsory PBLU entry
(Reserved)
Remote printer off line
(Reserved)
Overlapped cashier error
(Reserved)
Power off
(Reserved)
Compulsory non-add code
The cashier is not assigned.
(Reserved)
Overflow limitation
The open price entry is
inhibited.
The unit price entry is
inhibited.
The direct non-tendering
finalization after previous
tender entry is inhibited.
Read error of scale data
In default of
programming
ENTRY ERROR
MISOPERATION
NO RECORD
SECRET CODE
NOT FREE
MEMORY FULL
INSERT SLIP
NO AUTHORITY
OUT OF STOCK
SBTL COMPUL.
TEND COMPUL.
PB COMPUL.
OFF LINE
Text
no.
39-50
51
52-53
54
55-60
61
62
63
64
65-66
67
68-69
70
71-73
74
75
76
CASHIER ERR.
77-78
POWER OFF
79
# COMPULSORY
NOT ASSIGNED
81
80
OVER LIMIT.
INH. OPEN PR
82-83
84
85
86
INH. UNIT PR
NOT NON-TEND
SCALE ERROR
87
88
89-93
94
Description
(Reserved)
Weight on scale
(Reserved)
Entry of tare weight
(Reserved)
Desired code is not programmed
yet. (learning function)
Enter price and dept. no.
Enter price and dept. no.
Enter dept. no.
(Reserved)
REG buffer is full.
(Reserved)
Price entry at UPC refund
(Reserved)
Non-accessed UPC delete job
(Reserved)
Closing the drawer is
compulsory.
(Reserved)
Reading of undefined vender
coupon UPC
(Reserved)
Message for prompting entry
of secret code
(Reserved)
Data backup send success
Data backup receive success
Data backup communication
error
Backup data format error
Data backup time out error
(Reserved)
Age limitation error
In default of
programming
WEIGHT
ENTR TARE WT
NO RECORD
PRICE → DEPT
PRICE & DEPT
ENTER DEPT#
BUFFER FULL
ENTER PRICE
DELETE
CLOSE DRAWER
OP ENTER
ENTR SECRET#
SEND OK
RECEIVE OK
COM. ERROR
DATA ERROR
TIME OUT
AGE ERROR
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 185
LIST OF OPTIONS
For your register, the following Sharp options are available.
For further details on additional options that may be considered, please contact your dealer.
•Remote drawer model ER-04DW
•Till model ER-55CC2
•Key kit models
By using the following key kits, the keyboard layout can be changed on your register including the
expansion of the number of departments.
ER-11KT7: 30 regular size key kits
ER-12KT7: 30 1 x 2 size key kits
for ER-A410 only
ER-22KT7: 10 2 x 2 size key kits
ER-11DK7G: 30 regular size dummy key kits
ER-51DK7G: 10 5 x 1 size dummy key kits
•Barcode reader model ER-A6HS1 (only for the standard channel 1)
185
ER-A410/A420(SEC)-5
03.12.22 0:23 PM
Page 186
SPECIFICATIONS
Model:
Dimensions:
Weight:
Power source:
Power consumption:
Working temperature:
Electronics:
Built-in battery:
Display:
Operator display:
Customer display:
Printer:
Type:
Printing speed:
Printing capacity:
Other functions:
Paper roll:
Cash drawer:
Accessories:
ER-A410/A420
16.5 (W) x 16.8 (D) x 11.7 (H) in. (420 (W) x 427 (D) x 297 (H) mm)
29.1 lbs (13.2 kg)
120V ± 10% AC, 60Hz
Stand-by 9 W
Operating 46.5 W (max.)
32 to 104°F (0 to 40°C)
LSI (CPU) etc.
Rechargeable battery, memory holding time about 1 month
(with fully charged built-in battery, at room temperature)
LCD dot-matrix display (16 positions x 2 lines)
7-segment display (7 positions)
2-station thermal printer
Approx. 13.3 lines/second
24 digits each for receipt and journal paper
• Graphic logo printing function
• Logo text printing function
• Receipt (ON-OFF) function, journal selective function
• Receipt and journal independent paper feed function
Width: 1.75 ± 0.02 in. (44.5 ± 0.5 mm)
Max. diam.: 3.15 in. (80 mm)
Quality: High quality (0.06 to 0.08 mm thickness)
5 slots for bill and 5 for coin denominations
Manager key
2
Submanager key
2
Operator key
2
Drawer lock key
2
Paper roll
2
Take-up spool
1
Standard key sheet
1 (mounted on the keyboard)
Programming key sheet
1 (mounted on the keyboard)
Instruction manual
1 copy
* Specifications and appearance subject to change without notice for improvement.
186
for ER-A420 only
ER-A410/A420(SEC)HYO-2-3
03.11.4 8:19 AM
Page 3
NOTICE
BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WARRANTY THAT
YOUR SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user, of warranty
protection, Sharp extends a limited warranty to each of its authorized dealers, and in turn requires
each of its authorized dealers to extend its own warranty to you on terms that are no less favorable
than those given to the dealer by Sharp. You should be aware, however, that Sharp does not itself
extend any warranties, either express or implied, directly to you, the end-user, and no one is authorized to make any representations or warranties on behalf of Sharp. Specifically, SHARP DOES
NOT EXTEND TO YOU, THE END-USER, ANY EXPRESS WARRANTY OR ANY IMPLIED
WARRANTY OF MERCHANTABILITY, FITNESS FOR USE OR FITNESS FOR ANY PARTICULAR PURPOSE IN CONNECTION WITH THE HARDWARE, SOFTWARE, OR FIRMWARE
EMBODIED IN OR USED IN CONJUNCTION WITH THIS PRODUCT. Sharp is not responsible
for any damages or loss, either direct, incidental or consequential, which you, the end-user, may
experience as a result of your purchase or use of the hardware, software or firmware embodied in
or used in conjunction with this product. Your sole remedy in the event that you encounter any
difficulties with the product is against the authorized dealer from which you purchased the product.
In the event that this authorized dealer does not honor its warranty commitments, please contact
the General Manager of Sales, Retail and Financial System Division, ISG, Sharp Electronics Corporation, Sharp Plaza, P.O. Box 650, Mahwah, NJ 07430-2135 so that Sharp can try to help you to
assure complete satisfaction of all the warranty rights to which you are entitled from the authorized
dealer.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
1-800-BE-SHARP
http://www.sharp-usa.com
SHARP CORPORATION
Printed in China
KS(TINSE2520RCZZ)➀
HYO-1,4(SEC)
2
03.12.18, 6:20 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement