null  null
AUTOMOTIVE SPECIAL TOOLS
Suspension & Steering Service
Upper Arm Alignment Wrenches
These specialized 1/2" drive wrenches provide easy access
to the upper control arm bolts for front wheel alignment jobs.
No. 7414 – 13/16" hex wrench for use on 1985 to ’97 Ford
Aerostar vans. Wt., 12 oz.
No. 7534 – 22 mm hex wrench for use on 1990–2005 2WD
Chevrolet Astro and GMC Safari, and 1991–2005 AWD
Chevrolet Astro and GMC Safari vans. Wt., 12 oz.
No. 7536 – 3/4" hex wrench for use on 1973 to ’87
Chevrolet 2WD pickups, and Canadian-built 1985 to ’90
current GM Astro and Safari vans. Wt., 12 oz.
No. 7537 – 18 mm hex wrench for use on U.S.-built 1985 to
’90 GM Astro vans. Wt., 13 oz.
7414 is similar to
Ford No. 204-DO13
(D87T-3068-A)
7414
7537
7534
7536
Ford Caster/Camber Alignment Set
The tools in this set help ensure accurate caster/camber
adjustment on the front suspensions of 1979 to 1991
Ford and Mercury full size, rear wheel drive vehicles.
They effectively limit movement of the front suspension
once the cross shaft bolts are loosened.
No. 7091 – Ford caster/camber alignment set.
Wt., 1 lb., 2 oz.
7091
Ford 4WD Caster/Camber Sleeve Puller
Rusted or seized bushings are no match for this puller. It
easily pulls most aftermarket and OEM bushings on Ford
4WD vehicles. It’s the only tool that works on any angle
OEM bushing, removing it quickly and without damage. For
1980 to ’96 Ford Broncos, full-size E- and F-series vans
and pickups; 1983 to ’89 Ranger and Bronco II. The puller
comes with adapters to pull most aftermarket bushings
having removable retaining rings.
No. 7588A – Ford 4WD caster/camber sleeve puller.
Wt., 1 lb., 14 oz.
No. 221476 – Arnwood-style bushing adapter. Wt., 1 oz.
Similar to
Ford No. 204-D019
(D93T-3000-A)
7588A
Alignment Assist Tool
With this tool, you won’t need to remove tires to adjust the
camber on most GM and some Chrysler FWD vehicles.
The tool sits on top of a tire and presses against the strut to
prevent the tire from moving, allowing you to do the
adjustments. For Chrysler and GM vehicles with slotted strut
mounts that don’t use eccentric washers on the through
slots for camber adjustment. (Applications do not include
Buick Park Avenue, Cadillac Fleetwood, Oldsmobile 88 and
98, and Pontiac Bonneville – if they have rear air
suspension.)
No. 7676 – Alignment assist tool. Wt., 3 lbs., 2 oz.
Tie Rod Adjusting Tool
Here’s a tool that will fit most models of compact and
standard-size cars and light trucks. It has a four-position
feature and 360° rotation that lets you locate the tool to grip
the sleeve correctly, even when access is limited.
No. 7023 – Universal tie rod adjusting tool. Wt., 13 oz.
7676
Similar to Ford
No. T79P-3223-A
7023
99
AUTOMOTIVE SPECIAL TOOLS
Suspension & Steering Service
Tie Rod/Pitman Arm Adjusting Set
These tools are also
available individually.
These tools have a unique design that permits 360° rotation
of the adjusting sleeve, even where space is limited.
• Accommodates 1/2" drive ratchet or breaker bar.
• Set consists of the following tools in a blow-molded case:
No. 7095 – For compact cars with 3/4" diameter adjusting
sleeves. Wt., 7 oz.
No. 7096 – For full size cars with 7/8" diameter adjusting
sleeves. Wt., 7 oz.
No. 7097 – For light trucks with 1-1/8" diameter adjusting
sleeves. Wt., 8 oz.
No. 6274 – For Ford 3/4-ton and 1-ton trucks with
1-13/16" diameter adjusting sleeves. Wt., 10 oz.
No. 6084 – Pitman arm adjusting tool for Ford F-250 thru
F-450 trucks with 1-7/16" dia. adjusting sleeves. Wt., 7 oz.
No. 6275 – Tie rod/Pitman arm adjusting set. Wt., 3 lbs.
6275
Inner Tie Rod Removal Set
Similar to
Ford No. 211-D029
(D93L-3395-A)
7572
7594
7678
7593
Important: When removing and
installing inner tie rods, hold
steering rack shaft to prevent
damage to pinion gear.
Important: When removing and
installing inner tie rods, hold
steering rack shaft to prevent
damage to pinion gear.
7572
Remove and install inner tie rods without removing steering gear. The adapters fit into the tie rod socket, and a 1/2"
drive ratchet or breaker bar fits the drive end.
• Services both old and new style inner tie rods.
• For use on most Chrysler, Ford, and GM vehicles.
• No. 7572 socket is 16" long and is “stepped” to accept
1-3/16" tie rods and 1-5/16" tie rods.
• Nos. 7678, 7593, and 7594 adapters fit into socket and
work on 1-3/16", 1-5/16", and 1-7/16" tie rods.
No. 7595A – Inner tie rod removal set. Wt., 5 lbs., 2 oz.
2-in-1 Inner Tie Rod Socket Tool
Using “piggy-backed” sockets, this tool makes short work of
inner tie rod removal or installation.
• For use on Ford and Chrysler vehicles with rack and
pinion steering.
• Accommodates 1/2" drive ratchet or breaker bar.
• Socket is 16" long and is “stepped” to accept 1-3/16" tie
rods and 1-5/16" tie rods.
No. 7572 – 2-in-1 inner tie rod socket tool. Fits Ford and
most Chrysler vehicles with rack and pinion power steering.
Wt., 2 lbs., 2 oz.
Inner Tie Rod Adapter Sockets
7593
100
7594
7678
Important: When removing and installing
inner tie rods, hold steering rack shaft to
prevent damage to pinion gear.
These sockets enable you to remove and install inner tie
rods without removing steering gear. Drive end fits
No. 7572 inner tie rod sockets.
No. 7593 – 1-3/16" socket fits tie rod on Ford FWD vehicles
with rack and pinion steering. Wt., 15 oz.
No. 7594 – 1-5/16" socket fits tie rod on Ford RWD and
most Chrysler vehicles with rack and pinion steering.
Wt., 1 lb.
No. 7678 – 1-7/16" socket fits GM and Chrysler FWD cars
with Saginaw steering gear. Wt., 1 lb.
AUTOMOTIVE SPECIAL TOOLS
Suspension & Steering Service
Tie Rod Socket for Medium-Duty Trucks
Here’s a heavy-duty tool for removing tie rod ends on
Chrysler, Ford, and GM 1-ton trucks. It also works on many
medium-duty trucks, Class 2 through 6.
• Accommodates a 1/2" drive impact wrench.
No. 6065 – Truck tie rod socket. Wt., 1 lb., 8 oz.
6065
Inner Tie Rod Tool
Now you can work on inner tie rods without removing the
steering gear, saving time and effort. The tool’s design has
a dual purpose: The outer tube supports the steering rack,
preventing damage to the pinion gear. The inner socket fits
on the tie rod end.
7505A
• For use on Chrysler and GM vehicles with Saginaw
steering gear assemblies.
• Accommodates 1/2" drive ratchet or breaker bar.
• Used with No. 7504 tie rod crimping tool.
No. 7505A – Inner tie rod tool. Wt., 9 lbs., 7 oz.
Inner Tie Rod Crimper Tool
This handy tool will crimp a tie rod housing to the flats on
the rack to keep it from coming loose, while the steering
gear remains mounted. It’s much easier and neater than the
hammer and chisel method.
• For use on GM and Chrysler vehicles having Saginaw
steering gear assemblies.
• Used with No. 7505 inner tie rod tool.
No. 7504A – Inner tie rod crimper tool. Wt., 2 lbs., 11 oz.
7504A
Outer Tie Rod Ball Joint Separator
This tool is a must when you’re servicing outer tie rods
and ball joints on imported and domestic models, front or
rear wheel drive, cast or stamped-steel steering knuckles.
• Handles up to 5 tons of force.
• Jaws, once tightened, won’t slip on the knuckle.
No. 7503 – Outer tie rod ball joint separator.
Wt., 2 lbs., 12 oz.
7503
Steering Wheel Puller Leg Set
7929A
• Particularly useful during steering wheel removal when
there are no tapped holes in the assembly.
• The 7929A is designed for use with either the No. 7245 or
No. 7403 OTC steering wheel puller.
• These legs get behind the steering wheel assembly to
provide an even, straight pull. The collar is designed for
use on Ford and Chrysler vehicles.
• Works on:
1988–1993 Pontiac LeMans
1997–newer GM cars, SUVs, and light trucks
1997–newer Ford SUVs and light trucks
1999–newer Jeep Grand Cherokee
2003–newer Jeep Liberty
2004–newer Dodge Sprinter van
No. 7929A – Steering wheel puller leg set. Wt., 8 oz.
4-1/2"
reach
101
AUTOMOTIVE SPECIAL TOOLS
Suspension & Steering Service
Steering Wheel Puller
7245
This puller removes steering wheels on most domestic
and imported vehicles, with or without telescoping steering
columns. Five sets of cap screws are included for various
thread requirements. The forcing screw features a swivel
end to protect steering shaft. Cap screws included (pairs):
3/8-16 x 3-1/2; 5/16-18 x 3-1/2; 5/16-24 x 3-1/2; M8-1.25 x 90
mm; and 5/16-18 x 4 (SIR).
No. 7245 – Steering wheel puller with five pairs of cap
screws. Bar measures 4" x 1" x 1". Wt., 1 lb., 15 oz.
Steering Wheel, Pulley, and Flywheel Puller
Here’s a puller that works in a variety of applications.
It pulls steering wheels on most late model cars. It also
works as a regular 2/3-way puller to remove pulleys and
small engine flywheels. Cap screws included (pairs):
3/8-16 x 3-1/2 in.; 5/16-18 x 3-1/2 in.; 5/16-24 x 3-1/2 in.;
M8-1.25 x 90 mm; and 5/16-18 x 4 in. (SIR).
• Works on domestic cars with or without collapsible
steering columns.
No. 7403 – Steering wheel/pulley/flywheel puller.
Wt., 1 lb., 10 oz.
7403
Steering Wheel Remover/
Lock Plate Compressor Set
7927A
With this set, it’s easy to remove the steering wheels of
most domestic and imported vehicles, with or without tilt
steering columns. Also accesses the turn signal switch and
SIR modules on current GM vehicles.
• Includes No. 7815 steering wheel lock plate remover,
No. 7889 steering pivot pin remover for Saginaw steering
columns, No. 7245 steering wheel puller, plus four sets of
cap screws (2 of each size: M8–1.25 x 90 mm, 3/8"–16 x
3-1/2", 5/16"–24 x 3-1/2", and 5/16"–18 x 4").
• Contained in convenient plastic blow-molded case.
No. 7927A – Steering wheel remover/lock plate
compressor set. Wt., 4 lbs., 5 oz.
Steering Wheel Lock Plate Remover
7031A
This tool simplifies the removal and installation of round wire
snap rings that hold steering wheel lock plates. It’s a must
for accessing turn signal switches on AMC, Chrysler, and
GM model cars, with or without tilt steering columns.
Will not work on GM SIR steering columns.
• Also works on metric columns.
No. 7031A – Steering wheel lock plate remover.
Wt., 1 lb., 8 oz.
Steering Wheel Lock Plate Remover
102
7815
This is an essential tool for compressing steering wheel lock
plates on AMC, Chrysler, and GM vehicles, with or without
tilt steering columns. It’s also necessary for accessing the
turn signal switch and SIR modules on GM vehicles.
• Also works on metric columns.
No. 7815 – Steering wheel lock plate remover.
Wt., 1 lb., 12 oz.
AUTOMOTIVE SPECIAL TOOLS
Suspension & Steering Service
Steering Pivot Pin Remover
Tilt steering columns are much easier to service when your
tool box has one of these pivot pin removers in it. Works on
GM, Chrysler, and Ford vehicles with Saginaw tilt steering
columns.
No. 7889 – Steering pivot pin remover. Wt., 3 oz.
7889
Similar to
Kent Moore J-21894-01
Ford Lock Pin Remover
Removes tie rod inner socket retaining pin on Ford vehicles
with rack and pinion power steering. Replacement tips
available separately.
No. 7122R – Lock pin remover. Wt., 5 oz.
No. 37907 – Tip for 7122R. Wt., 1 oz.
7122R
GM Power Steering Pump Pulley Installer
This tool offers easy, damage-free installation of power
steering pump pulleys. It works on 1988–95 GM Quad
4 engines; 1990–94 Chevrolet Lumina APV, Oldsmobile
Silhouette, and Pontiac Trans Sport vehicles; 1990–94 3.1L
V6 engines; 1994–newer 3100 GM V6; 1999–newer 3400
GM V6. Threads are 3/8–16" to fit pulley shaft threads.
No. 7209 – GM power steering pump pulley installer.
Wt., 7 oz.
7209
GM Power Steering Pump Pulley Service Kit
Remove and install the power steering pump pulley easily
and without damaging the pump shaft or pulley.
• Includes remover and installer.
No. 7362 – GM power steering pump pulley service kit.
Wt., 1 lb., 3 oz.
7362
Ford Power Steering Pump Pulley Installer
Installs power steering pump pulleys on 1992–newer Ford
Crown Victoria and Mercury Grand Marquis with 4.6 V8
engine, 1997–newer Ford truck with 4.2 & 4.6 V6, 5.4 V8,
and 6.8 V10 engines.
• 8 mm x 1.25" threads fit Ford’s C111 pump.
No. 7771 – Ford power steering pump pulley installer.
Wt., 1 lb., 8 oz.
Similar to
211-185
7771
Ford Air Bag Simulator
Today’s air bag systems have self-diagnostic capabilities,
but sometimes these internal diagnostics must be serviced
or replaced. That’s when our air bag simulators come in
handy. In fact, it’s almost impossible to check and resolve
air bag fault codes without such tools. This makes the
simulators essential equipment for body shops and other
types of service centers.
No. 7955 – Special one-ohm resistor for use on air bags on
Probe vehicles. Wt., 6 oz.
No. 7956 – Special two-ohm resistor for use on 1993–02
Ford System II air bags. Wt., 6 oz.
No. 7957 – Special three-ohm resistor for use on Mercury
Villager air bag systems. Wt., 6 oz.
103
AUTOMOTIVE SPECIAL TOOLS
Suspension & Steering Service
Power Steering Pump/
Alternator Remover/Installer Tool
• Reversible 2-in-1 tool removes and installs press-fit
alternator and power steering pump pulleys.
• Also removes and installs other press-fit pulleys with a
hub diameter of 1-1/8" (28 mm), 1-1/4" (32 mm), 1-5/16"
(34 mm), or 1-3/8" (35 mm).
No. 4681 – Power steering pump/alternator remover/installer
tool. Wt., 2 lbs.
4681
Power Steering/Alternator Pulley Puller/
Installer Set
• Properly replaces pressed-on power steering and 4529
Similar to
Ford No. 211-016
(T69L-10300-B)
7185
alternator pulleys on Ford, Chrysler, and late GM engines.
• Housed in a blow-molded plastic storage case.
No. 4529 – Power steering and alternator pulley puller/
installer. Wt., 1 lb., 14 oz.
Power Steering Pump/Alternator Pulley
Remover
This puller removes pulleys on most Chrysler, Ford, GM,
and VW vehicles fitted with Saginaw, Thompson, or Ford’s
C2 and C111 power steering pumps; GM belt-driven vacuum
pumps on cars; and press-on water pump pulleys on GM
4- and 6-cylinder engines. It works on pulleys with hub
diameters of 1-1/8", 1-1/4", 1-5/16", and 1-3/8".
• Designed to ensure damage-free removal.
No. 7185 – Power steering pump/alternator pulley
remover. Wt., 13 oz.
Power Steering Pump Pulley Service Set
• A complete set of tools required to remove and install
4530
power steering pump pulleys of most domestic vehicles.
• Fits pulley hubs with diameters of 1-1/8", 1-1/4", 1-5/16"
and 1-3/8".
• Includes the necessary adapters for servicing: GM 3.1L,
3100, 3400, and 3800 V6 engines, GM 2.3L Quad 4 four cylinder engines, and Ford 4.6L & 5.4L V8, 6.8 V10
engines.
No. 4530 – Power steering pump pulley puller/installer set.
Wt. 2 lbs., 5 oz.
Power Steering Pump Pulley Kit
104
7830A
This kit has nearly everything you need to remove and install
power steering pump pulleys in Chrysler, Ford, and GM vehicles with Saginaw, Thompson, and Ford C111 and C2 power
steering pumps. Fits 1-1/8", 1-1/4", 1-5/16" and 1-3/8" pulley
hub diameters, including 1988–newer GM cars equipped
with Quad 4 engines; 1991–94 GM 3.1L V6; 1991–newer
3800 V6 engines; 1994–newer GM 3100 V6; 1999–newer
GM 3400 V6, and 1992–newer Ford Crown Victoria and
Mercury Grand Marquis with 4.6 V8 engine, 1997–newer
Ford truck with 4.2 & 4.6 V6, 5.4 V8, and 6.8 V10 engines.
• Also includes No. 7931 spacer for work on Chrysler
Cirrus, Dodge Stratus, and Plymouth Breeze.
No. 7830A – Power steering pump pulley kit. Wt., 1 lb., 10 oz.
AUTOMOTIVE SPECIAL TOOLS
Suspension & Steering Service and Ford Cam Tools
Ford Diesel Vacuum Pump Pulley Remover Jaws
These jaws, together with No. 7185 pulley remover, make
quick work of vacuum pump removal on newer Ford diesel
engines.
• For use on 1984 to ’87 6.9L, and 1988–2003 7.3L.
No. 7922 – Ford diesel vacuum pump pulley remover jaws.
Wt., 8 oz.
Similar to
Ford No. 300-D054
(D84T-9486-A)
7922
Power Steering Pump Pulley Installer
This is an ideal companion to our No. 7185 pulley remover.
It’s a real timesaver for installing power steering pump
pulleys and GM press-on water pump pulleys.
• Designed to ensure damage-free installation.
• Internal roller bearing allows for easy turning.
• Threads are 3/8"-16 to match pulley shafts.
No. 7005 – Power steering pump pulley installer. Wt., 11 oz.
Similar to
Ford No. 211-009
(T65P-3A733-C)
7005
The OTC Ford cam tools ensure correct cam timing
when servicing timing belts, chains, head gaskets,
or other valve train repairs.
Ford Cam Tool Kit
6486
No. 6486 – Ford cam tool kit for 2.0L Zetec engines in
Contour, Mystique, and Focus. Contains tool Nos. 6474 and
No. 6475. Wt., 1 lb.
Ford Cam Tool Kit
6487
No. 6487 – Ford cam tool kit for 1992 thru 2004 4.6L, 5.4L
V8, and 6.8L V10 engines. Contains tool Nos. 6476, 6477,
6009, 6020, and molded storage case.
Wt., 5 lbs.
Note: See page 106, kit 6489 for applications.
Ford Cam Tool Kit
No. 6488 – Ford cam tool kit for 1997 thru 2004 4.0L
Explorer/Mountaineer SOHC V6 engines. Kit contains
tool Nos. 6478, 6479, 6480, 6481, 6482, 6484, 6485,
and molded storage case.
Wt., 7 lbs. 10 oz.
6488
Note: See page 106, kit 6489 for applications.
105
AUTOMOTIVE SPECIAL TOOLS
Ford Cam Tool Application Chart
Ford Cam Tool Kit
6489
No. 6489 – Ford master cam tool kit containing
all 22 cam tools covering 1992 thru 2004 for over
50 applications, in a molded storage case.
Wt., 12 lbs. 5 oz.
Ford cam tool application chart for No. 6489
Note: Some applications require more than one tool to accomplish the task.
Year
Make & Model
Engine
Tool Description
1995–1997
Aerostar
3.0L V6
1996–1998
Aerostar
4.0L V6
1994–2002
Contour
2.0L 4 cyl. DOHC Zetec
1997–2002
Contour
2.0L 4 cyl. DOHC Zetec
1991–1998
Crown Victoria
4.6L 2V V8
1992–1998
Crown Victoria
4.6L 2V V8
1997–2003
Econoline
4.2L V6
1997–1998
Econoline
4.6L & 5.4L V8, 6.8L V10
1997–2006
Econoline
4.6L & 5.4L
1997–2006
Econoline
5.4L V8
1997–2006
Econoline
6.8L V10
1997–2006
Econoline
Windsor V8
1997–1998
Expedition
5.4L V8
1997–2004
Expedition
5.4L V8
1996–1998
Explorer
4.0L V6
1997–2006
Explorer
4.0L SOHC V6
1999–2002
Explorer
4.0L Push Rod V6
1996–1998
Explorer
5.0L V8
1999–2002
Explorer
5.0L V8
1997–2003
F-Series Truck
4.2L V6
1997–1998
F-Series Truck
4.6L & 5.4L V8
1997–2004
F-Series Truck
4.6L & 5.4L
1997–2004
F-Series Truck
5.4L V8
1997–2004
F-Series Truck
Windsor V8
1994–1995
Mustang
3.8L V6
1996–1998
Mustang
3.8L V6
1999–2004
Mustang
3.8L V6
106
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Alignment Tool
Crankshaft TDC Timing Pin
Cam Positioning Tool
Cam Positioning Tool
Cam Sensor Sync Tool
Cam Positioning Tool
Cam Positioning Tool
Cam Positioning Tool Set
Cam Holding Tool
Cam Positioning Tool Set
Cam Holding Tool
Cam Holding Tool
Cam Positioning Tool
Cam Positioning Tool
Cam Positioning Tool Set
Cam Holding Tool
Cam Sensor Sync Tool
Cam Gear Holding Tool
Crankshaft Holding Tool
Cam Holding Tool Adapter
Cam Holding Tool
Cam Gear Hldg Tool Adapter
Timing Chain Tensioner Tool
Cam Gear Bolt Socket & Ext.
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Positioning Tool
Cam Positioning Tool
Cam Positioning Tool Set
Cam Holding Tool
Cam Holding Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
OTC
Part No.
Ford Am.
Part No.
6472
T95T-12200-A
6472
T95T-12200-A
6474
T94P-6256-CH
6475
T97P-6000-A
6009
T91P-6256-A
6020
T92P-6256-A
6469
T96T-12200-A
6009
T91P-6256-A
6020 T92P-6256-A
6476
T96T-6256-AR
6477
T96T-6256-B
6476
T96T-6256-AR
6477
T96T-6256-B
6477
T96T-6256-B
6009
T91P-6256-A
6020
T92P-6256-A
6476
T96T-6256-AR
6477
T96T-6256-B
6472
T95T-12200-A
6478
T97T-6256-B
6479
T97T-6303-A
6480
T97T-6256-D
6481
T97T-6256-C
6482
T97T-6256-A
6484
T97T-6K254-A
6485
T97T-6256-F, -G
6483
6469
T96T-12200-A
6470
6469
T96T-12200-A
6009 T91P-6256-A
6020
T92P-6256-A
6476
T96T-6256-AR
6477
T96T-6256-B
6477
T96T-6256-B
6467
T89P-12200-A
6469
T96T-12200-A
6470
Global
Part No.
303-529
303-529
303-465
303-574
303-380
303-413
303-562
303-380
303-413
303-S568
303-557
303-S568
303-557
303-557
303-380
303-413
303-S568
303-557
303-529
303-564
303-573
303-576
303-577
303-578
303-571
303-565, -575
303-638
303-562
303-630
303-562
303-380
303-413
303-S568
303-557
303-557
303-358
303-562
303-630
AUTOMOTIVE SPECIAL TOOLS
Ford Cam Tool Application Chart
Ford cam tool application chart for No. 6489
Note: Some applications require more than one tool to accomplish the task.
Year
Make & Model
Engine
Tool Description
1996–2001
Mustang
4.6L 4V
1996–2004
Mustang
4.6L 4V
1993–1997
Probe
2.0L 4 cyl.
1989–1997
Ranger
2.3L, 4 cyl. dual plug
1995–1997
Ranger
3.0L V6
1998–2006
Ranger
3.0L V6
1996–1998
Ranger
4.0L V6
1993–1995
Taurus
3.0L V6
1996–1997
Taurus
3.0L V6 2-valve
1998–2006
Taurus
3.0L V6
1989–1995
Thunderbird
Supercharged 3.8L V6
1990–1995
Thunderbird
3.8L V6
1997
Thunderbird
3.8L V6
1995–1997
Windstar
3.0L V6
1998–2003
Windstar
3.0L V6
1995
Windstar
3.8L V6
1996–1998
Windstar
3.8L V6
1999–2003
Windstar
3.8L V6
1998
Lincoln Navigator
5.4L V8
1998–2004
Lincoln Navigator
5.4L V8
1993–1997 Lincoln Mark Series 4.6L 4V
1993–1998 Lincoln Mark Series 4.6L 4V
1995–2002 Lincoln Continental 4.6L 4V
2003–2005
Lincoln Aviator
4.6L 4V
1989–1995
Cougar
Supercharged 3.8L V6
1990–1995
Cougar
3.8L V6
1997
Cougar
3.8L V6
1991–1998
Grand Marquis
4.6L 2V V8
1992–1998
Grand Marquis
4.6L 2V V8
1997–2006
Mountaineer
4.0L SOHC V6
1999–2004
Mountaineer
4.0L Push Rod V6
1996–1998
Mountaineer
5.0L V8
1999–2001
Mountaineer
5.0L V8
1994–2002
Mystique
2.0L 4 cyl. DOHC Zetec
1997–2002
Mystique
2.0L 4 cyl. DOHC Zetec
1993–1995
Sable
3.0L V6
1996–1997
Sable
3.0L V6 2-valve
1998–2004
Sable
3.0L V6
2003–2004
Mercury Marauder 4.6L 4V
OTC
Part No.
Camshaft Positioning Tool
Camshaft Holding Tool
Cam Pulley Holding Tool
Crankshaft Sensor Positioner
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Positioning Tool
Cam Positioning Tool
Cam Positioning Tool Set
Cam Holding Tool
Secondary Timing Chain Tensioner
Camshaft Positioning Tool
Camshaft Holding Tool
Camshaft Positioning Tool
Camshaft Holding Tool
Camshaft Holding Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Positioning Tool
Cam Positioning Tool
Cam Gear Holding Tool
Crankshaft Holding Tool
Cam Holding Tool Adapter
Cam Holding Tool
Cam Gear Holding Tool Adapter
Timing Chain Tensioner Tool
Cam Gear Bolt Socket & Ext.
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Alignment Tool
Crankshaft TDC Timing Pin
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Cam Sensor Sync Tool
Camshaft Positioning Tool
Camshaft Holding Tool
Ford Am.
Part No.
525216
525217
6468
T92C-6256-AH
6466
T89P-6316-A
6472
T95T-12200-A
6473
6472
T95T-12200-A
6471
T93P-12200-A
6472
T95T-12200-A
6473
6467
T89P-12200-A
6467
T89P-12200-A
6469
T96T-12200-A
6472
T95T-12200-A
6473
6467
T89P-12200-A
6469
T96T-12200-A
6470
6009
T91P-6256-A
6020
T92P-6256-A
6476
T96T-6256-AR
6477
T96T-6256-B
525218
525216
525217
525216
525217
525217
6467
T89P-12200-A
6467
T89P-12200-A
6469
T96T-12200-A
6009
T91P-6256-A
6020
T92P-6256-A
6478
T97T-6256-B
6479
T97T-6303-A
6480
T97T-6256-D
6481
T97T-6256-C
6482
T97T-6256-A
6484
T97T-6K254-A
6485
T97T-6256-F, -G
6483
6469
T96T-12200-A
6470
6474
T94P-6256-CH
6475
T97P-6000-A
6471
T93P-12200-A
6472
T95T-12200-A
6473
525217
525217
Global
Part No.
303-445
303-446
303-398
303-354
303-529
303-589
303-529
303-453
303-529
303-589
303-358
303-358
303-562
303-529
303-589
303-358
303-562
303-630
303-380
303-413
303-S568
303-557
303-447
303-445
303-446
303-445
303-446
303-446
303-358
303-358
303-562
303-380
303-413
303-564
303-573
303-576
303-577
303-578
303-571
303-565, -575
303-638
303-562
303-630
303-465
303-574
303-453
303-529
303-589
303-446
303-446
107
AUTOMOTIVE SPECIAL TOOLS
Ford Cam Tool Application Chart
The OTC Ford cam tools ensure correct cam timing
when servicing timing belts, chains, head gaskets, or
other valve train repairs.
Ford 4.6L 4-Valve Cam Timing Kit
• Kit includes: Camshaft positioning tool, camshaft holding
tool, crankshaft positioning tool, secondary chain
tensioner tool.
• Saves time; all tools required for camshaft timing are in
one kit.
No. 6498 – Ford 4.6L 4-valve cam timing kit.
Wt., 6 lbs., 11 oz.
6498
Ford 4.6L V8 4 valve Cam Timing application chart for 6498
Year
1993-1998
1995-2002
1996-2001
2003-2004
1993-1998
1995-2002
1996-2002
2003-2004
2005-2006
2003-2004
2003-2005
1993-1997
1995-1997
1996-1997
1993-1998
1995-2002
1996-2001
2003-2004
2003-2004
2005-2006
2003-2005
108
Make
Lincoln
Lincoln
Ford
Mercury
Lincoln
Lincoln
Ford
Ford
Ford
Mercury
Lincoln
Lincoln
Lincoln
Ford
Lincoln
Lincoln
Ford
Mercury
Ford
Ford
Lincoln
Model
Mark VIII
Contiental
Mustang
Marauder
Mark VIII
Contiental
Mustang
Mustang
Mustang
Marauder
Aviator
Mark VIII
Contiental
Mustang
Mark VIII
Contiental
Mustang
Marauder
Mustang
Mustang
Aviator
Note: Some applications require more than one tool to accomplish the task.
Engine
4.6L VIN V
4.6L VIN V
4.6L VIN V
4.6L VIN V
4.6L VIN V
4.6L VIN V
4.6L VIN V
4.6L VIN Y
4.6: VIN H
4.6L VIN V
4.6L VIN H
4.6L VIN V
4.6L VIN V
4.6L VIN V
4.6L VIN V
4.6L VIN V
4.6L VIN V
4.6L VIN V
4.6L VIN Y
4.6: VIN H
4.6L VIN H
Tool Decription
Camshaft Positioning Tool
Camshaft Positioning Tool
Camshaft Positioning Tool
Camshaft Positioning Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Secondary Timing Chain Tensioner tool
Secondary Timing Chain Tensioner tool
Secondary Timing Chain Tensioner tool
Crankshaft Positioning Tool
Crankshaft Positioning Tool
Crankshaft Positioning Tool
Crankshaft Positioning Tool
Crankshaft Positioning Tool
Crankshaft Positioning Tool
Crankshaft Positioning Tool
OTC PN
525216
525216
525216
525216
525217
525217
525217
525217
525217
525217
525217
525218
525218
525218
525219
525219
525219
525219
525219
525219
525219
OE PN
303-445
303-445
303-445
303-445
303-446
303-446
303-446
303-446
303-446
303-446
303-446
303-447
303-447
303-447
303-448
303-448
303-448
303-448
303-448
303-448
303-448
AUTOMOTIVE SPECIAL TOOLS
Chrysler/Jeep Cam Tool Set
The Chrysler/Jeep cam timing tools are provided to ensure
correct cam timing when servicing timing belts, chains, head
gaskets, or performing other valve train repairs.
These 15 tools are based on OE designs and are offered to
service the following applications:
Cam positioning is an IMPORTANT procedure. If cam
timing is not correct, the engine may still run, but emissions
and mileage will be affected. The engine computer may also
initiate the “Check Engine” light.
No. 6689 – Chrysler/Jeep cam tool set. Wt., 25 lbs.
6689
Chrysler / Jeep Cam Tool application chart for 6689
Year
1990-2006
1990-2006
1990-2000
1993-1996
1993-1997
1993-1997
1993-1997
1994-2006
1994-2006
1994-2000
1994-2006
1995-2006
1995-1999
1995-2000
2003-2006
1995-1999
1995-2000
1995-2000
1995-2000
2001-2006
1995-2001
1995-2000
1995-2000
2001-2006
1998-2004
1998-2004
1999-2006
2005-2006
2005-2006
2004-2006
2006
2006
1998-2006
998-2006
2000-2006
2000-2006
1999-2006
Make
Chrysler
Dodge
Plymouth
Chrysler
Dodge
Chrysler
Dodge
Chrysler
Dodge
Plymouth
Dodge
Dodge
Dodge
Dodge
Dodge
Chrysler
Chrysler
Chrysler
Chrysler
Chrysler
Plymouth
Plymouth
Plymouth
Chrysler
Chrysler
Chrysler
Chrysler
Chrysler
Chrysler
Chrysler
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Jeep
Model
Town & Country Van
Caravan & Grand Caravan
Voyager & Grand Voyager
Conorde
Intrepid
Conorde
Intrepid
Town & Country Van
Caravan & Grand Caravan
Voyager & Grand Voyager
Ram Truck
Neon
Avanger
Avanger
Neon
Sebring
Sebring
Cirrus
Cirrus
Sebring
Neon
Breeze
Breeze
PT Cruiser
Conorde
Conorde
300
300
PT Cruiser
Pacifica
Charger
Charger
Intrepid
Intrepid
Dakota
Durango
Grand Cherokee
Note: Some applications require more than one tool to accomplish the task.
Engine
3.3 L V6
3.3 L V6
3.3 L V6
3.3 L V6
3.3 L V6
3.5L V6
3.5L V6
3.8L V6
3.8L V6
3.8L V6
8.0L V10
2.0L I4
2.0L I4
2.5L V6
2.4L I4
2.0L I4
2.5L V6
2.4L I4
2.5L V6
2.4L I4
2.0L I4
2.0L I4
2.4L I4
2.4L I4
2.7L V6
3.2L V6
3.5L V6
2.7L V6
2.7L V6
3.5L V6
3.5L V6
2.7L V6
2.7L V6
3.2L V6
4.7L V8
4.7L V8
4.7L V8
Tool Decription
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
Crankshaft Damper Puller
OTC PN
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
6667 or 513990
OE PN
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
8454
109
AUTOMOTIVE SPECIAL TOOLS
Chrysler/Jeep Cam Tool Application Chart
Chrysler / Jeep Cam Tool application chart for 6689
Year
2006
1994-1997
1993-1997
1994-1997
1993-1997
2002-2006
2005-2006
1998-2004
2002-2006
2005-2006
2006
1999-2006
2006
2000-2006
2000-2006
2002-2006
2002-2006
2004-2006
2002-2006
2004-2006
2004-2006
2002-2006
2004-2006
2002-2006
2004-2006
2004-2006
1999-2006
2006
2000-2006
2000-2006
2002-2006
1999-2006
2006
2000-2006
2000-2006
2002-2006
2001-2005
2001-2005
2001-2005
2001-2005
1981-1988
1981-1989
1982-1983
1983-1988
1984-1986
1984-1989
1984-1987
1983-1990
1987-1994
1985-1989
1986-1993
110
Make
Jeep
Chrysler
Chrysler
Chrysler
Dodge
Chrysler
Chrysler
Dodge
Dodge
Dodge
Dodge
Jeep
Jeep
Dodge
Dodge
Dodge
Jeep
Jeep
Dodge
Dodge
Dodge
Jeep
Jeep
Dodge
Dodge
Dodge
Jeep
Jeep
Dodge
Dodge
Dodge
Jeep
Jeep
Dodge
Dodge
Dodge
Chrysler
Dodge
Chrysler
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Model
Commander
New Yorker & LHS
Conorde
New Yorker & LHS
Intrepid
Sebring
300
Intrepid
Stratus
Magnum
Charger
Grand Cherokee
Commander
Durango
Dakota
Ram Truck
Liberty
Grand Cherokee
Ram Truck
Dakota
Durango
Liberty
Grand Cherokee
Ram Truck
Dakota
Durango
Grand Cherokee
Commander
Durango
Dakota
Ram Truck
Grand Cherokee
Commander
Durango
Dakota
Ram Truck
Sebring
Stratus
Sebring
Stratus
Omni
Aries
400
600
Charger
Daytona
Caravan & Grand Caravan
Shelby
Shadow
Lancer
Daytona
Note: Some applications require more than one tool to accomplish the task.
Engine
4.7L V8
3.5L V6
3.5L V6
3.5L V6
3.5L V6
2.7L V6 vin R
2.7L V6 vin R
2.7L V6 vin R
2.7L V6 vin R
2.7L V6 vin R
2.7L V6 vin R
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
3.7L V6
3.7L V6
3.7L V6
3.7L V6
3.7L V6
3.7L V6
3.7L V6
3.7L V6
3.7L V6
3.7L V6
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
2.4L I4 vin G
2.4L I4 vin G
3.0L V6 vin H
3.0L V6 vin H
2.2 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.2 L I4
Tool Decription
Crankshaft Damper Puller
Crankshaft Damper Puller
Camshaft alignment tools
Camshaft alignment tools
Timing Chain Tensioner Reset Tool
Timing Chain Tensioner Reset Tool
Timing Chain Tensioner Reset Tool
Timing Chain Tensioner Reset Tool
Timing Chain Tensioner Reset Tool
Timing Chain Tensioner Reset Tool
Timing Chain Tensioner Reset Tool
Timing Chain Wedge
Timing Chain Wedge
Timing Chain Wedge
Timing Chain Wedge
Timing Chain Wedge
Timing Chain Wedge
Timing Chain Wedge
Timing Chain Wedge
Timing Chain Wedge
Timing Chain Wedge
Camshaft Wrench
Camshaft Wrench
Camshaft Wrench
Camshaft Wrench
Camshaft Wrench
Idler Shaft Remover
Idler Shaft Remover
Idler Shaft Remover
Idler Shaft Remover
Idler Shaft Remover
Tensioner lock pin
Tensioner lock pin
Tensioner lock pin
Tensioner lock pin
Tensioner lock pin
Camshaft Holding Pins
Camshaft Holding Pins
Camshaft Holding Pins
Camshaft Holding Pins
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
OTC PN
6667 or 513990
6667 or 513990
7999 or 522888
7999 or 522888
522890
522890
522890
522890
522890
522890
522890
522892
522892
522892
522892
522892
522893
522893
522893
522893
522893
522894
522894
522894
522894
522894
522896
522896
522896
522896
522896
522897
522897
522897
522897
522897
522898
522898
522898
522898
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
OE PN
8454
8454
6642
6642
8186
8186
8186
8186
8186
8186
8186
8350
8350
8350
8350
8350
8379
8379
8379
8379
8379
8428
8428
8428
8428
8428
8517
8517
8517
8517
8517
8514
8514
8514
8514
8514
8599
8599
8599
8599
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
AUTOMOTIVE SPECIAL TOOLS
Chrysler/Jeep Cam Tool Application Chart
Chrysler / Jeep Cam Tool application chart for 6689
Year
1986-1989
1986-1988
1987-1989
1987-1995
1988-1991
1988-1993
1989-1994
1989-1995
1982-1990
1983-1988
1984-1986
1986-1993
1986-1987
1981-1989
1981-1989
1984-1988
1982-1986
1989-1994
1986-1988
1986-1989
1987-1995
1987-1994
1990-1995
1989-1995
1989-1995
1991-1997
1992-1994
1992-1994
1984-1991
1999-2006
2006
2000-2006
2000-2006
2002-2006
1999-2006
2006
2000-2006
2000-2006
2002-2006
Make
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Dodge
Chrysler
Chrysler
Chrysler
Chrysler
Chrysler
Plymouth
Plymouth
Plymouth
Plymouth
Plymouth
Plymouth
Plymouth
Plymouth
Plymouth
Plymouth
Dodge
Eagle
Dodge
Eagle
Dodge
Dodge
Jeep
Jeep
Dodge
Dodge
Dodge
Jeep
Jeep
Dodge
Dodge
Dodge
Model
Aries
600
Lancer
Caravan & Grand Caravan
Shelby
Dynasty
Shadow
Spirit
Lebaron
New Yorker Laser
Lebaron
New Yorker
Horizon
Reliant
Voyager
Turismo
Sundance
Caravelle
Reliant
Voyager
Sundance
Acclaim
Colt
Summit
Stealth
Summit
Colt
Colt
Grand Cherokee
Commander
Durango
Dakota
Ram Truck
Grand Cherokee
Commander
Durango
Dakota
Ram Truck
Note: Some applications require more than one tool to accomplish the task.
Engine
2.5 L I4
2.5 L I4
2.5 L I4
2.5 L I4
2.5 L I4
2.5 L I4
2.5 L I4
2.5 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.5 L I4
2.5 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.2 L I4
2.5 L I4
2.5 L I4
2.5 L I4
2.5 L I4
2.5 L I4
2.4L I4
2.4L I4
3.0L V6
2.4L I4
2.4L I4
2.0L I4
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
4.7L V8
Tool Decription
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Tensioner
Timing Belt Wrench
Timing Belt Wrench
Timing Belt Wrench
Timing Belt Wrench
Secondary Timing Chain Holder
Secondary Timing Chain Holder
Secondary Timing Chain Holder
Secondary Timing Chain Holder
Secondary Timing Chain Holder
Secondary Timing Chain Holder
Secondary Timing Chain Holder
Secondary Timing Chain Holder
Secondary Timing Chain Holder
Secondary Timing Chain Holder
OTC PN
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
7695 or 522899
522900A
522900A
7997 or 522901
7997 or 522901
7997 or 522901
7997 or 522901
522902
522902
522902
522902
522902
522902
522902
522902
522902
522902
OE PN
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
C-4703
MD-998738
MD-998738
MD-998767
MD-998767
MD-998767
MD-998767
8515
8515
8515
8515
8515
8515
8515
8515
8515
8515
111
AUTOMOTIVE SPECIAL TOOLS
GM Cam Tool Application Chart
GM In-line 4-Cylinder
Cam Tool Set
• Comprehensive tool kit designed to save
time when servicing GM 4-cylinder engines.
• Tools are actually easier to use than the
original OE essential tools.
No. 6685 – GM In-line 4-Cylinder Cam Tool Set.
Wt., 17 lbs., 8 oz.
6685
GM In-line 4-Cylinder Cam Tool Application Chart for 6685
Year
1988-1995
1990-1991
1987-1991
1992-1995
1988-1995
1995
1996-1998
1996-2002
1996-1998
1999-2001
1996-2001
1996-2002
1988-1998
1996-2002
1987-1991
1990-1991
1992-1998
1999-2001
1998-2001
1995-2002
1996-1998
1996-2002
1996-1998
1999-2001
1996-2001
1996-2002
1988-1995
1987-1991
1990-1991
1992-1995
1988-1995
1995
2002-2005
2003-2006
2004-2005
2002-2004
2002-2005
2002-2005
112
Make
Buick
Oldsmobile
Oldsmobile
Oldsmobile
Pontiac
Pontiac
Buick
Chevrolet
Oldsmobile
Oldsmobile
Pontiac
Pontiac
Buick
Chevrolet
Oldsmobile
Oldsmobile
Oldsmobile
Oldsmobile
Pontiac
Pontiac
Buick
Chevrolet
Oldsmobile
Oldsmobile
Pontiac
Pontiac
Buick
Oldsmobile
Oldsmobile
Oldsmobile
Pontiac
Pontiac
Chevrolet
Chevrolet
Chevrolet
Oldsmobile
Pontiac
Pontiac
Model
Skylark
Cutlass Supreme
Calais
Achieva
Grand Am
Sunfire
Skylark
Cavalier
Achieva
Alero
Grand Am
Sunfire
Skylark
Cavalier
Calais
Cutlass Supreme
Achieva
Alero
Grand Am
Sunfire
Skylark
Cavalier
Achieva
Alero
Grand Am
Sunfire
Skylark
Calais
Cutlass Supreme
Achieva
Grand Am
Sunfire
Cavalier
Malibu
Malibu Classic
Alero
Sunfire
Grand Am
Note: Some applications require more than one tool to accomplish the task.
Engine
2.3L
2.3L
2.3L
2.3L
2.3L
2.3L
2.4L
2.4L
2.4L
2.4L
2.4L
2.4L
2.3L/2.4L
2.3L/2.4L
2.3L/2.4L
2.3L/2.4L
2.3L/2.4L
2.3L/2.4L
2.3L/2.4L
2.3L/2.4L
2.4L
2.4L
2.4L
2.4L
2.4L
2.4L
2.3L
2.3L
2.3L
2.3L
2.3L
2.3L
2.2L vin F
2.2L vin F
2.2L vin F
2.2L vin F
2.2L vin F
2.2L vin F
Tool Decription
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Sprocket Wrench
Camshaft Timing Alignment Pins
Camshaft Timing Alignment Pins
Camshaft Timing Alignment Pins
Camshaft Timing Alignment Pins
Camshaft Timing Alignment Pins
Camshaft Timing Alignment Pins
Camshaft Timing Alignment Pins
Camshaft Timing Alignment Pins
Timing Chain Tensioner & Shoe Retainer
Timing Chain Tensioner & Shoe Retainer
Timing Chain Tensioner & Shoe Retainer
Timing Chain Tensioner & Shoe Retainer
Timing Chain Tensioner & Shoe Retainer
Timing Chain Tensioner & Shoe Retainer
Timing Chain Tensioner Retainer
Timing Chain Tensioner Retainer
Timing Chain Tensioner Retainer
Timing Chain Tensioner Retainer
Timing Chain Tensioner Retainer
Timing Chain Tensioner Retainer
Timing Chain Tensioner Loading Tools
Timing Chain Tensioner Loading Tools
Timing Chain Tensioner Loading Tools
Timing Chain Tensioner Loading Tools
Timing Chain Tensioner Loading Tools
Timing Chain Tensioner Loading Tools
OTC PN
527046
527046
527046
527046
527046
527046
527049
527049
527049
527049
527049
527049
527045
527045
527045
527045
527045
527045
527045
527045
532174
532174
532174
532174
532174
532174
532195
532195
532195
532195
532195
532195
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
OE PN
J-36013
J-36013
J-36013
J-36013
J-36013
J-36013
J-39579
J-39579
J-39579
J-39579
J-39579
J-39579
J-36008A
J-36008A
J-36008A
J-36008A
J-36008A
J-36008A
J-36008A
J-36008A
NA
NA
NA
NA
NA
NA
J-36589
J-36589
J-36589
J-36589
J-36589
J-36589
J-45027
J-45027
J-45027
J-45027
J-45027
J-45027
AUTOMOTIVE SPECIAL TOOLS
GM Cam Tool Application Chart
GM In-line
4-Cylinder Cam Tool Application Chart for 6685
Year
Make
Model
Note: Some applications require more than one tool to accomplish the task.
Engine
Tool Decription
2000-2005
Saturn
L Series
2.2L vin F
Timing Chain Tensioner Loading Tools
2002-2006
Saturn
Vue
2.2L vin F
Timing Chain Tensioner Loading Tools
2003-2006
Saturn
Ion
2.2L vin F
Timing Chain Tensioner Loading Tools
2005-2006
Chevrolet
Cobalt
2.2L vin F
Timing Chain Tensioner Loading Tools
2005-2006
Chevrolet
Cobalt
2.4L vin B
Timing Chain Tensioner Loading Tools
2006
Chevrolet
HHR
2.4L vin B
Timing Chain Tensioner Loading Tools
2006
Pontiac
G6
2.4L vin B
Timing Chain Tensioner Loading Tools
2006
Pontiac
Pursuit
2.4L vin B
Timing Chain Tensioner Loading Tools
2006
Pontiac
Solstice
2.4L vin B
Timing Chain Tensioner Loading Tools
2005-2006
Chevrolet
Cobalt
2.0L
Timing Chain Tensioner Loading Tools
2002-2005
Chevrolet
Cavalier
2.2L vin F
Camshaft Sprocket Holding Tool
2003-2006
Chevrolet
Malibu
2.2L vin F
Camshaft Sprocket Holding Tool
2004-2005
Chevrolet
Malibu Classic
2.2L vin F
Camshaft Sprocket Holding Tool
2002-2004
Oldsmobile
Alero
2.2L vin F
Camshaft Sprocket Holding Tool
2002-2005
Pontiac
Sunfire
2.2L vin F
Camshaft Sprocket Holding Tool
2002-2005
Pontiac
Grand Am
2.2L vin F
Camshaft Sprocket Holding Tool
2000-2005
Saturn
L Series
2.2L vin F
Camshaft Sprocket Holding Tool
2002-2006
Saturn
Vue
2.2L vin F
Camshaft Sprocket Holding Tool
2003-2006
Saturn
Ion
2.2L vin F
Camshaft Sprocket Holding Tool
2005-2006
Chevrolet
Cobalt
2.2L vin F
Camshaft Sprocket Holding Tool
2005-2006
Chevrolet
Cobalt
2.0L
Camshaft Sprocket Holding Tool
2005-2006
Chevrolet
Cobalt
2.4L vin B
Camshaft Sprocket Holding Tool
2006
Chevrolet
HHR
2.4L vin B
Camshaft Sprocket Holding Tool
2006
Pontiac
G6
2.4L vin B
Camshaft Sprocket Holding Tool
2006
Pontiac
Pursuit
2.4L vin B
Camshaft Sprocket Holding Tool
2006
Pontiac
Solstice
2.4L vin B
Camshaft Sprocket Holding Tool
2002-2005
Chevrolet
Cavalier
2.2L vin F
Timing Chain Holders
2003-2006
Chevrolet
Malibu
2.2L vin F
Timing Chain Holders
2004-2005
Chevrolet
Malibu Classic
2.2L vin F
Timing Chain Holders
2002-2004
Oldsmobile
Alero
2.2L vin F
Timing Chain Holders
2002-2005
Pontiac
Sunfire
2.2L vin F
Timing Chain Holders
2002-2005
Pontiac
Grand Am
2.2L vin F
Timing Chain Holders
2000-2005
Saturn
L Series
2.2L vin F
Timing Chain Holders
2002-2006
Saturn
Vue
2.2L vin F
Timing Chain Holders
2003-2006
Saturn
Ion
2.2L vin F
Timing Chain Holders
2005-2006
Chevrolet
Cobalt
2.2L vin F
Timing Chain Holders
2005-2006
Chevrolet
Cobalt
2.0L
Timing Chain Holders
2005-2006
Chevrolet
Cobalt
2.4L vin B
Timing Chain Holders
OTC PN
OE PN
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527061-1 & 527061-2
527056
527056
527056
527056
527056
527056
527056
527056
527056
527056
527056
527056
527056
527056
527056
527056
536186 & 536187
536186 &
536187
536186 & 536187
536186 & 536187
536186 & 536187
536186 & 536187
536186 & 536187
536186 & 536187
536186 & 536187
536186 & 536187
536186 & 536187
536186 & 536187
J-45027
J-45027
J-45027
J-45027
J-45027
J-45027
J-45027
J-45027
J-45027
J-45027
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-43655
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
113
AUTOMOTIVE SPECIAL TOOLS
GM Cam Tool Application Chart
GM In-line 4-Cylinder Cam Tool Application Chart for 6685
Note: Some applications require more than one tool to accomplish the task.
Year
Make
Model
Engine
Tool Decription
2006
Chevrolet
HHR
2.4L vin B
Timing Chain Holders
2006
Pontiac
G6
2.4L vin B
Timing Chain Holders
2006
Pontiac
Pursuit
2.4L vin B
Timing Chain Holders
2006
Pontiac
Solstice
2.4L vin B
Timing Chain Holders
2004-2006
Chevrolet
Colorado
2.8L Camshaft Sprocket Holding Tool
2004-2006
GMC Canyon
2.8L Camshaft Sprocket Holding Tool
2004-2006
Chevrolet
Colorado
2.8L Camshaft Holding Tool
2004-2006
GMC Canyon
2.8L Camshaft Holding Tool
2002-2005
Chevrolet
Cavalier
2.2L vin F
Crankshaft Pulley Holder
2003-2006
Chevrolet
Malibu
2.2L vin F
Crankshaft Pulley Holder
2004-2005
Chevrolet
Malibu Classic
2.2L vin F
Crankshaft Pulley Holder
2002-2004
Alero
2.2L vin F
Crankshaft Pulley Holder
Oldsmobile
2002-2005
Pontiac
Sunfire
2.2L vin F
Crankshaft Pulley Holder
2002-2005
Pontiac
Grand Am
2.2L vin F
Crankshaft Pulley Holder
2000-2005
Saturn
L Series
2.2L vin F
Crankshaft Pulley Holder
2002-2006
Saturn
Vue
2.2L vin F
Crankshaft Pulley Holder
2003-2006
Saturn
Ion
2.2L vin F
Crankshaft Pulley Holder
2005-2006
Chevrolet
Cobalt
2.2L vin F
Crankshaft Pulley Holder
2005-2006
Chevrolet
Cobalt
2.0L
Crankshaft Pulley Holder
2005-2006
Chevrolet
Cobalt
2.4L vin B
Crankshaft Pulley Holder
2006
Chevrolet
HHR
2.4L vin B
Crankshaft Pulley Holder
2006
Pontiac
G6
2.4L vin B
Crankshaft Pulley Holder
2006
Pontiac
Pursuit
2.4L vin B
Crankshaft Pulley Holder
2006
Pontiac
Solstice
2.4L vin B
Crankshaft Pulley Holder
1996-1998
Buick
Skylark
2.4L
Crankshaft Pulley Holder
1996-2002
Chevrolet
Cavalier
2.4L
Crankshaft Pulley Holder
1996-1998
Oldsmobile
Achieva
2.4L
Crankshaft Pulley Holder
1999-2001
Oldsmobile
Alero
2.4L
Crankshaft Pulley Holder
1996-2001
Pontiac
Grand Am
2.4L
Crankshaft Pulley Holder
1996-2002
Pontiac
Sunfire
2.4L
Crankshaft Pulley Holder
2004-2006
Chevrolet
Aveo
1.6L
Timing Belt Adjuster
2000-2002
Saturn
SC-2,SL-2, SW-2
1.9L vin 7
Camshaft Holding Tool
1999-2002
Saturn
SC-2,SL-2, SW-2
1.9L vin 7
Camshaft Timing Alignment Pins
1999-2002
Saturn
SC-2,SL-2, SW-2
1.9L vin 7
Timing Chain Tensioner Retainer
2004-2006
Chevrolet
Colorado
2.8L Timing Chain Holder
2004-2006
GMC Canyon
2.8L Timing Chain Holder
114
OTC PN
536186 & 536187
536186 & 536187
536186 & 536187
536186 & 536187
536181
536181
536172
536172
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536178
536173
536174
536254
536255
536265
536265
OE PN
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 & J44217-2
J-44217-1 &
J 44217-2
J-44222
J-44222
J-44221
J-44221
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-38122
J-42492A
J-43299
NA
NA
J-44217-46
J-44217-46
AUTOMOTIVE SPECIAL TOOLS
GM Cam Tool Application Chart
GM NorthStar V8 Cam Tool Set
•Kit is indispensable for quickly and correctly servicing
GM NorthStar 4.0L and 4.6L V8 engines.
•Over one million NorthStar V8s have been sold since
1993; cylinder heads and valve trains tend to wear out somewhere between 80,000 to 120,000 miles.
No. 6686 – GM NorthStar V8 cam tool kit.
Wt., 5 lbs., 1 oz.
6686
GM NorthStar V8 Cam Tool Application Chart for 6686
Note: Some applications require more than one tool to accomplish the task.
Year
Engine
Tool Decription
OTC PN
OE PN
1993-1999
1994- 1999
2000-2002
2000-2005
2004-2006
2005-2006
2006
2001-2003
2000-2002
2000-2005
2004-2006
2005-2006
2006
2001-2003
2000-2002
2000-2005
2004-2006
2005-2006
2006
2004-2006
2006
2001-2003
2004-2006
2004-2006
2004-2006
2004-2006
2004-2006
2004-2006
4.6L
4.6L
4.6L
4.6L
4.6L
4.6L
4.6L
4.0L
4.6L
4.6L
4.6L
4.6L
4.6L
4.0L
4.6L
4.6L
4.6L
4.6L
4.6L
4.6L
4.6L
4.0L
4.6L VIN A
4.6L VIN A
4.6L VIN A
4.6L VIN A
4.6L VIN A
4.6L VIN A
Cam Chain Tension Tool
Cam Chain Tension Tool
Crankshaft Rotating Tool
Crankshaft Rotating Tool
Crankshaft Rotating Tool
Crankshaft Rotating Tool
Crankshaft Rotating Tool
Crankshaft Rotating Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Secondary Drive Sprocket Fixture
Secondary Drive Sprocket Fixture
Secondary Drive Sprocket Fixture
Secondary Drive Sprocket Fixture
Secondary Drive Sprocket Fixture
Secondary Drive Sprocket Fixture
Secondary Drive Sprocket Fixture
Secondary Drive Sprocket Fixture
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
527048
527048
527050
527050
527050
527050
527050
527050
527057
527050
527057
527057
527057
527057
527058
527058
527058
527058
527058
527058
527058
527058
529636
529637
529638
529636
529637
529638
J-38822
J-38822
J-39946
J-39946
J-39946
J-39946
J-39946
J-39946
J-44212
J-44212
J-44212
J-44212
J-44212
J-44212
J-44213
J-44213
J-44213
J-44213
J-44213
J-44213
J-44213
J-44213
Make
Model
Cadillac Cadillac Cadillac Cadillac Cadillac Cadillac Cadillac Oldsmobile
Cadillac Cadillac Cadillac Cadillac Cadillac Oldsmobile
Cadillac Cadillac Cadillac Cadillac Cadillac Pontiac Buick
Oldsmobile
Cadillac Cadillac Cadillac Pontiac Pontiac Pontiac Eldorado Seville
Deville Concours
Eldorado Seville Deville
XLR, SRX
STS
DTS
Aurora
Eldorado Seville Deville
XLR, SRX
STS
DTS
Aurora
Eldorado Seville Deville
XLR, SRX
STS
DTS
Bonneville Lucerne
Aurora
SRX, STS, XLR
SRX, STS, XLR
SRX, STS, XLR
Bonneville GPX
Bonneville GPX
Bonneville GPX
115
AUTOMOTIVE SPECIAL TOOLS
GM Cam Tool Application Chart
GM 6 Cylinder Cam Tool Set
•Required tools to adjust and hold cam shaft timing
on GM 3.0 and 3.2 V-6 engines.
•Kit is designed to save shop time when servicing
GM 3.0 and 3.2 V-6 engines.
6687
No. 6687 – GM 6 cylinder cam tool set. Wt., 4 lbs., 13 oz.
GM 6-Cylinder Cam Tool Application Chart for 6687
Year
2002-2003
1997-2001
2002-2003
1997-2001
2002-2003
1997-2001
2002-2003
1997-2001
2002-2003
1997-2001
2002-2003
1997-2001
2002-2003
1997-2001
Make
Cadillac
Cadillac
Cadillac
Cadillac
Cadillac
Cadillac
Cadillac
Cadillac
Cadillac
Cadillac
Cadillac
Cadillac
Cadillac
Cadillac
Model
Note: Some applications require more than one tool to accomplish the task.
Engine
CTS
Catera
CTS
Catera
CTS
Catera
CTS
Catera
CTS
Catera
CTS
Catera
CTS
Catera
3.2L vin N
3.0L vin R
3.2L vin N
3.0L vin R
3.2L vin N
3.0L vin R
3.2L vin N
3.0L vin R
3.2L vin N
3.0L vin R
3.2L vin N
3.0L vin R
3.2L vin N
3.0L vin R
Tool Decription
Camshaft Locking Tool
Camshaft Locking Tool
Camshaft Locking Tool
Camshaft Locking Tool
Crankshaft Holding Tool
Crankshaft Holding Tool
Camshaft Alignment Gauge
Camshaft Alignment Gauge
Timing Belt Installation Tool
Timing Belt Installation Tool
Timing Belt Tensioner Wrench
Timing Belt Tensioner Wrench
Crankshaft socket
Crankshaft socket
OTC PN
536594
536594
536595
536595
536596
536596
536608
536608
536611
536611
536612
536612
536613
536613
OE PN
J-42069-1
J-42069-1
J-42069-2
J-42069-2
J-42069-10
J-42069-10
J-42069-20
J-42069-20
J-42069-30
J-42069-30
J-42069-40
J-42069-40
MKM-602-21
MKM-602-21
GM In-line 5, 6, or V6 Cam Tool Set
•Comprehensive tool kit designed to save time when
6688
servicing GM 5-, 6-cylinder engines.
•Tools are actually easier to use than the original
OE essential tools.
No. 6688 – GM In-line 5, 6, or V6 cam tool set.
Wt., 17 lbs., 4 oz.
GM In-line 5, 6, or V6 Cam Tool Application Chart for 6688
Year
2005-2006
2004-2006
2004-2006
2005-2006
2004-2006
2004-2006
2005-2006
2004-2006
2004-2006
2005-2006
116
Make
Buick
Buick
Cadillac
Cadillac
Cadillac
Cadillac
Buick
Buick
Cadillac
Cadillac
Model
Lacrosse
Rendezvous
CTS
STS
SRX
CTS
Lacrosse
Rendezvous
CTS
STS
Note: Some applications require more than one tool to accomplish the task.
Engine
3.6L vin 7
3.6L vin 7
3.6L vin 7
3.6L vin 7
3.6L vin 7
2.8L vin T
3.6L vin 7
3.6L vin 7
3.6L vin 7
3.6L vin 7
Tool Decription
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Crankshaft Turning Socket
Crankshaft Turning Socket
Crankshaft Turning Socket
Crankshaft Turning Socket
OTC PN
536589 & 536590
536589 & 536590
536589 & 536590
536589 & 536590
536589 & 536590
536589 & 536590
536588
536588
536588
536588
OE PN
EN-46108
EN-46108
EN-46108
EN-46108
EN-46108
EN-46108
EN-46111
EN-46111
EN-46111
EN-46111
AUTOMOTIVE SPECIAL TOOLS
GM Cam Tool Application Chart
GM In-line 5, 6, or V6 Cam Tool Application Chart for 6688
Year
2004-2006
2004-2006
2005-2006
2004-2006
2004-2006
2005-2006
2004-2006
2004-2006
2005-2006
2004-2006
2004-2006
2005-2006
2004-2006
2004-2006
2005-2006
2004-2006
2004-2006
2005-2006
2004-2006
2004-2006
2002-2004
2004-2006
2002-2006
2002-2006
2004-2006
2004-2006
2004-2006
2002-2004
2004-2006
2002-2006
2002-2006
2004-2006
2004-2006
2004-2006
2002-2004
2004-2006
2002-2006
2002-2006
2004-2006
2004-2006
2001-2004
2001-2002
1999-2002
2001-2002
1999-2002
2001-2002
1999-2002
2001-2002
1999-2002
2004-2005
2004-2005
2004-2005
Make
Cadillac
Cadillac
Buick
Buick
Cadillac
Cadillac
Cadillac
Cadillac
Buick
Buick
Cadillac
Cadillac
Cadillac
Cadillac
Buick
Buick
Cadillac
Cadillac
Cadillac
Cadillac
Oldsmobile
Buick
Chevrolet
GMC
Chevrolet
GMC
Cadillac
Oldsmobile
Buick
Chevrolet
GMC
Chevrolet
GMC
Cadillac
Oldsmobile
Buick
Chevrolet
GMC
Chevrolet
GMC
Chevrolet
Oldsmobile
Oldsmobile
Oldsmobile
Oldsmobile
Oldsmobile
Oldsmobile
Oldsmobile
Oldsmobile
Saturn
Saturn
Saturn
Model
SRX
CTS
Lacrosse
Rendezvous
CTS
STS
SRX
CTS
Lacrosse
Rendezvous
CTS
STS
SRX
CTS
Lacrosse
Rendezvous
CTS
STS
SRX
CTS
Bravada
Rainier
Trailblazer
Envoy
Colorado
Canyon
CTS
Bravada
Rainier
Trailblazer
Envoy
Colorado
Canyon
CTS
Bravada
Rainier
Trailblazer
Envoy
Colorado
Canyon
Tracker
Aurora
Intrigue
Aurora
Intrigue
Aurora
Intrigue
Aurora
Intrigue
Vue
Vue
Vue
Note: Some applications require more than one tool to accomplish the task.
Engine
3.6L vin 7
2.8L vin T
3.6L vin 7
3.6L vin 7
3.6L vin 7
3.6L vin 7
3.6L vin 7
2.8L vin T
3.6L vin 7
3.6L vin 7
3.6L vin 7
3.6L vin 7
3.6L vin 7
2.8L vin T
3.6L vin 7
3.6L vin 7
3.6L vin 7
3.6L vin 7
3.6L vin 7
2.8L vin T
4.2L vin S
4.2L vin S
4.2L vin S
4.2L vin S
3.5L vin 5 5 cylinder
3.5L vin 5 5 cylinder
2.8L vin T
4.2L vin S
4.2L vin S
4.2L vin S
4.2L vin S
3.5L vin 5 5 cylinder
3.5L vin 5 5 cylinder
2.8L vin T
4.2L vin S
4.2L vin S
4.2L vin S
4.2L vin S
3.5L vin 5 5 cylinder
3.5L vin 5 5 cylinder
2.5L
3.5L vin H
3.5L vin H
3.5L vin H
3.5L vin H
3.5L vin H
3.5L vin H
3.5L vin H
3.5L vin H
3.5L vin 4
3.5L vin 4
3.5L vin 4
Tool Decription
Crankshaft Turning Socket
Crankshaft Turning Socket
Timing Chain Tensioner Pins
Timing Chain Tensioner Pins
Timing Chain Tensioner Pins
Timing Chain Tensioner Pins
Timing Chain Tensioner Pins
Timing Chain Tensioner Pins
Timing Chain Tensioner Tool
Timing Chain Tensioner Tool
Timing Chain Tensioner Tool
Timing Chain Tensioner Tool
Timing Chain Tensioner Tool
Timing Chain Tensioner Tool
Camshaft Locking Tool
Camshaft Locking Tool
Camshaft Locking Tool
Camshaft Locking Tool
Camshaft Locking Tool
Camshaft Locking Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Holding Tool
Camshaft Sprocket Holding Tool
Camshaft Sprocket Holding Tool
Camshaft Sprocket Holding Tool
Camshaft Sprocket Holding Tool
Camshaft Sprocket Holding Tool
Camshaft Sprocket Holding Tool
Camshaft Sprocket Holding Tool
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Retention Tools
Timing Chain Tensioner Pin
Timing Chain Tensioner Pin
Timing Chain Tensioner Pin
Camshaft Holding Tool
Camshaft Holding Tool
Cam Gear Holding Fixture
Cam Gear Holding Fixture
Crankshaft Socket
Crankshaft Socket
Camshaft Holding Tool
Timing Chain Tensioner Pin
Timing Belt Tensioner Retainer
OTC PN
536588
536588
536587
536587
536587
536587
536587
536587
536587
536587
536587
536587
536587
536587
536584 & 586585
536584 & 586585
536584 & 586585
536584 & 586585
536584 & 586585
536584 & 586585
536172
536172
536172
536172
536172
536172
536181
536181
536181
536181
536181
536181
536181
536189 & 536187
536189 & 536187
536189 & 536187
536189 & 536187
536189 & 536187
536189 & 536187
536189 & 536187
536586
536586
536586
527051
527051
527052
527052
527055
527055
536583
536586
536582
OE PN
EN-46111
EN-46111
EN-46112
EN-46112
EN-46112
EN-46112
EN-46112
EN-46112
J-45027
J-45027
J-45027
J-45027
J-45027
J-45027
EN-46105
EN-46105
EN-46105
EN-46105
EN-46105
EN-46105
J-44221
J-44221
J-44221
J-44221
J-44221
J-44221
J-44222
J-44222
J-44222
J-44222
J-44222
J-44222
J-44222
J-44217
J-44217
J-44217
J-44217
J-44217
J-44217
J-44217
EN-46330
EN-46330
EN-46330
J-42038
J-42038
J-42042
J-42042
J-43032
J-43032
EN-46337
EN-46330
EN-46331
117
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Ford Crankshaft Positioning Tool
6024
Similar to Ford
No. 303-448.
(B)
• Designed for use on Ford 1993–2004 4.2L, 4.6L 2-valve,
4.6L 4-valve, 5.4L V8, and 6.8L V10 engines when
installing timing chains. These engines are not freewheeling, and if an engine has “jumped time,” it is
possible the cylinder heads have to be removed because
of damage to the valves or pistons.
• Easily installs over the crankshaft and engine front cover
alignment dowel to position the crankshaft at top-dead center — the correct position for timing chain installation.
OTC recommends the No. 6024 be used with Nos. 6009
and 6020 (but it is not required).
No. 6024 ­­– Ford crankshaft positioning tool. Wt., 10 oz.
Camshaft Timing Tools
• Indispensable for servicing timing belts on GM 3.4L V6
(A)
6045
(C)
Similar to Miller
No. 6642
7999
DOHC engine. Works on 1991–1996 Chevrolet Lumina
and 1995–1997 Monte Carlo, 1991–1998 Olds Cutlass
Supreme and Pontiac Grand Prix.
• Tool (A) holds the camshaft in the correct position; tool
(B) is used to pull the cam gear from the camshaft; and
tool (C) is used to turn the cam gear to time the camshaft.
No. 6045 ­­– Camshaft timing tools. Wt., 3 lbs., 12 oz.
Chrysler Camshaft Alignment Tool Set
These special brackets are necessary to ensure exact alignment of the camshaft sprockets during timing belt installation
on all 1993–current LH vehicles with a 3.5L OHC engine.
No. 7999 – Chrysler camshaft alignment tool set. Wt., 8 oz.
Chrysler Timing Belt Wrench
Similar to
Miller No. MD-998767
7997
Similar to
Miller No. C-4703
7695
118
Correctly adjusts the timing belt tension on 1991–1994 3.0L
DOHC Dodge Stealth, 1992–1994 Eagle Summit, 1992–
1994 Dodge Colt, and 1984–1991 2.0L Dodge Colt. For use
with a 1/4" drive ratchet.
No. 7997 – Chrysler timing belt wrench. Wt., 3 oz.
Chrysler Timing Belt Adjustment Wrench
Guessing at the correct tension on timing belts is bad news
– for you and your customers. To make belt tension adjustment easier on Chrysler’s 2.2L and 2.5L engines, this
wrench is a big help. It holds the tension on the belt for you,
while you tighten the nut to the correct torque—eliminates
over or under tightening. Plus, the weight can be shifted
from one side of the wrench to the other to accommodate
confining areas.
No. 7695 – Chrysler timing belt adjustment wrench.
Wt., 13 oz.
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Universal Belt Tension Gauge
• Belt tension gauges are used to check drive belt
tension on drive belts to ensure maximum belt
and bearing life.
• Scale reads 30–180 inch lbs.
No. 6673 – Universal belt tension gauge.
Wt., 1 lb., 7 oz.
6673
Ford Spark Plug Socket
• This unique and design works on 2004–newer
Ford vehicles with 5.4L, 4.6L, 5.4L, 3-valve Triton V8 & 6.8L Triton V10 engines.
• Socket end is 9/16". Soft rubber insert holds and protects
spark plug during removal and installation.
• Extension is part of the socket. Easily fits down spark
plug tube in cylinder head.
• Socket has a 3/8" drive for use with a ratchet or breaker bar.
No. 6900 – Ford F-150 spark plug socket, 5-7/8" long. Wt., 7 oz.
6900
5/8" & 13/16" Spark Plug Sockets
• Works on GM, Chrysler, Ford, and many import vehicles
with 5/8" or 13/16" spark plugs.
• Socket end has a soft rubber insert to hold and protect the
spark plug during removal and installation.
Drive
end is 3/8" for use with ratchet or breaker bar.
•
No. 6899 – 5/8" Spark plug socket, 4-7/8" long. Wt., 7 oz.
No. 6898 – 13/16" Spark plug socket, 4-7/8" long. Wt., 7 oz.
6899
6898
3-Piece Spark Plug Socket Set
This kit combines the most popular spark plug sockets. Each
socket has a 3/8" drive end for use with a ratchet or breaker
bar. Socket ends have soft rubber inserts to hold and protect
the spark plug during removal and installation.
• No. 6898 works on GM, Chrysler, Ford, and many import
vehicles with 13/16" spark plugs, 4-7/8" long.
No.
6899 works on GM, Chrysler, Ford, and many import
•
vehicles with 5/8" spark plugs, 4-7/8" long.
• No. 6900 works on 2004–newer Ford vehicles with 5.4L, 4.6L, 5.4L, 3-valve Triton V8 & 6.8L Triton V10 engines,
5-7/8" long.
No. 6897 – 3-piece spark plug socket set. Wt., 2 lbs., 2 oz.
6897
Ford Valve Spring Compressor Tool
Compresses valve springs for quicker, easier camshaft,
valve seal, valve spring, or retainer service—because you
don’t have to remove the head from the engine first! It’s
an OEM-approved tool that you use with a 3/8" ratchet or
breaker bar. Works on: 1991–2004 Ford vehicles with 4.6L,
two-valve, V8 engines; 4.6 4V, 5.4 V8 and 6.8 V10.
No. 7928 – Ford valve spring compressor tool. Wt., 6 oz.
Similar to
Ford No. 303-567
7928
119
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Ford Rear Main Seal Installer
7786
Similar to
Ford No. 303-178
(T82L-6701-A)
7834
Similar to
Ford No. 303-5524
This installer is the most accurate way to ensure that the rear
main seal is set to the correct depth on the crankshaft. The
installer fits over the seal, and with the two bolts included,
attaches to the engine crankshaft. By alternately tightening the
bolts, the seal is pulled into place quickly, easily, and with no
damage to the rear main seal. Works on 2.0L, 2.3L, 2.3L OHC,
2.5L, 2.5L OHC 4-cylinder engines; 3.0L 2V, 3.0L 4V, 3.4L
SOHC, 3.8L, 3.8L SC V6 engines; 4.6L 2V, 4.6L 4V, 5.0L and
5.8L V8 engines.
No. 7786 – Ford rear main seal installer. Wt., 2 lbs., 4 oz.
Ford Rear Crankshaft Seal Installer
• This installer works on crankshaft rear oil seals that come
with or without a metal wear sleeve.
• Designed for use on 1993–1997 Aerostar or 1993–2006
Ranger and Explorer w/4.0L V6 engine
No. 7834 – Ford rear crankshaft seal installer. Wt., 1 lbs., 12 oz.
GM Oil Pump Drive Removal Tool
On certain GM V6 engines, the oil pump drive is difficult to get
at, making it a real hassle to remove it to repair o-ring leaks.
This tool removes the oil pump drive from the engine without
first having to remove the exhaust cross-over pipe or other
components.
For 1987–89 2.8L V6 engines; 1990–94 3.1L V6 engines;
1994 and newer 3100 V6 engines; and 1999 and newer 3400
engines.
No. 7943 – GM oil pump drive removal tool. Wt., 8 oz..
7943
GM Crankshaft Balancer Puller Kit
and Adapter Set
7912
7911
Everything you need to pull harmonic balancers having three
tapped holes. The shoulder bolts are designed to prevent them
from being installed too deeply, protecting the crank sensor
and/or interrupter rings from damage. The spacer adapter gives
the puller’s forcing screw something to push against. The kit
works on 1990–2002 3300 and 3800 V6 engines. The No. 7911
adapter set consists of the spacer adapter and shoulder bolts
only, for use with your No. 518 or No. 6930 flange-type puller.
No. 7911 – GM crankshaft balancer puller adapter set. Includes
shoulder bolts and spacer adapter only. Wt., 8 oz.
No. 7912 – GM crankshaft balancer puller kit. Includes No. 518
flange-type puller and No. 7911 adapter set. Wt., 3 lbs., 2 oz.
Chrysler Harmonic Balancer Holding Tool
• Designed as a holding ring with three pins to fit into the
120
6495
openings on a harmonic balancer.
• Use with a 1/2" ratchet or breaker bar to hold the harmonic
balancer in place when turning the bolt that holds the
balancer to the crankshaft. Also use to hold the balancer
when removing it from the engine.
• Works on 1990–newer 3.3L V6 vans; 1994–newer 3.8L V6;
1993–1997 3.3L and 3.5L V6 cars; 1998–newer 2.7L, 3.2L,
and 3.5L V6 cars.
No. 6495 – Chrysler harmonic balancer holding tool.
Wt., 1 lb., 10 oz.
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Harmonic Balancer Puller
Designed for removing damper pulleys in tight engine compartments, without removing the radiator. Use on the following:
• GM 2000 Generation III 4.8L, 5.3L, 5.7L 6.0L, and 8.1L V8s.
Also works on Cadillac 4.5, 4.6, and 4.9L V8s beginning in
1988. Chevrolet trucks 2003–later 4.2L I6, 2004–current 3.5L
I5 and 2005–current 2.8L I4.
Chrysler
engines from 1990–later, including 2.0L, 2.4L-4s; plus
•
2.5L, 2.7L, 3.3L, 3.5L, and 3.8L V6s.
• Ford 1995–later V8 engines with 3 spoke pressed on damper.
• Mitsubishi Eclipse 1995–1999 2.0L DOHC non-turbo.
• Kit contains the 3-jaw puller, four lengths of forcing rods, and
a forcing screw with a 3/8” square drive for ratchet use, and a
3/4” hex for wrench or socket use.
Replacement rods:
No.
No.
No.
No.
537757-4
537757-5
537757-6
537757-7
–
–
–
–
5/16”
5/16”
5/16”
5/16”
x
x
x
x
4”
5-13/32”
6-1/2”
7.13/32”
6667
No. 6667 – Harmonic balancer puller. Wt., 2 lbs., 11 oz.
Harmonic Balancer Puller Set
• Includes No. 6267 puller, which removes the harmonic
balancer from the crankshaft; and No. 6495 holding tool,
which holds the harmonic balancer when tightening or
loosening the crankshaft bolt, or removing the balancer.
No. 6284 – Harmonic balancer puller set, includes both the
No. 6267 and the No. 6495 tools. Wt., 3 lbs., 7 oz.
6284
Chrysler Crankshaft Damper
Remover/Installer Kit
The special 3-jaw puller is used with the insert to remove the
crankshaft damper whenever timing belt, water pump, or front
cover service is required. The tool kit includes a damper
installing tool with bearing.
• Services Chrysler-built 2.0L, 2.4L, 2.5L, 3.3L and 3.5L
engines.
• 1995–newer 3.3L and 3.5L V6 used in Chrysler New Yorker
and Concorde, Dodge Intrepid, and Eagle Vision; 1995–
newer 2.0L, 2.4L 4-cyl., and 2.5L V6 used in Cirrus, Stratus,
and Breeze; 1995–newer 2.0L 4-cyl. used in Neon.
No. 6075 – Chrysler crankshaft damper remover/installer kit.
Wt., 4 lbs., 8 oz.
Distributor Bushing Remover
• Used to remove the distributor drive shaft lower bushing
from the engine block.
• Works on Chrysler, Dodge, and Plymouth 3.9L V6, 5.2L and
5.9L V8 vehicles with distributors.
No. 6292 – Distributor bushing remover. Wt., 1 lb., 4 oz.
6075
Similar to
Miller No. C-3054
6292
121
AUTOMOTIVE SPECIAL TOOLS
Engine Service
6293
Similar to
Miller No. C-3053
Distributor Bushing Installer/Reamer
• Used to install the distributor drive shaft lower bushing into
the engine block. Then use this same tool to ream the new
bushing so the distributor drive shaft correctly fits into the
bushing.
• Works on Chrysler, Dodge, and Plymouth 3.9L V6, 5.2L &
5.9L V8 vehicles with distributors.
• Compatible with OEM and aftermarket distributor drive
bushings.
No. 6293 – Distributor bushing installer/reamer. Wt., 2 lbs.
Compression Tester - Deep Well Connector
5603
Use with OTC compression testers or other compression
Features and benefits:
• Solid steel 8" length shaft.
• Upper t-wing grip for ease of installation and removal.
• Popular 14 mm thread for both flat and tapered seat plugs.
• Corrosion resistant nickel plated finish.
No. 5603 – Compression tester – deep well connector. Wt., 15 oz.
Compression Tester Ford Adapter
5607
Use with OTC compression testers to access hard to reach
spark plug holes.
Features and benefits:
• WorksTMon 2004 and newer Ford 4.6 and 5.4 L, 3 valve
Triton V-8 engines. (Triton is a Registered Trade Mark of
the Ford Motor Co.)
Easy-to-turn
feature makes starting thread fast.
•
• Use with compression testers with 14 mm thread.
No. 5607 – Compression tester Ford adapter. Wt., 15 oz.
Compression Tester Kit
5606
122
Designed for complete compression testing on gasoline
engines, including domestic, imports, motorcycles, marine,
and small engines. Unique problem solving features
for today’s limited space engine compartments.
Features and benefits:
• Corrosion resistant nickel plated finish.
• Adapters work on both flat and tapered seat plugs.
• Extra long 25" flex hose gauge assembly with quick
coupler, allows easy viewing out of cluttered engine
compartment.
• 2-1/2" gauge features chrome bezel and rugged protective
outer boot.
• Dual scale gauge reads 0-300 psi and 0-2100 kPa.
• 12" flex-14 mm standard reach.
• 12" flex-14 mm long reach.
• 10 mm,12 mm, and 18 mm thread adapters.
• Rugged blow molded hard case with removable lid.
• Repair parts kit.
No. 5606 – Compression tester kit. Wt., 3 lbs., 11 oz.
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Motorcycle Compression Tester Kit
Designed specifically for testing motorcycle and small engines,
this kit features a specially designed compression gauge
and hose assembly, plus three different size hose adapters.
Compression Tester and hose lengths are designed for optimal
viewing along side engine. Covers most popular motorcycle
and small engine plug sizes.
Functions and Features:
• Corrosion resistant nickel plated finish
• 10" flex hose gauge assembly with quick coupler.
• 2-1/2" gauge features chrome bezel and rugged
protective outer boot
• Dual scale gauge reads 0-300 psi and 0-2100 kPa
• 12" flex hose -14 mm standard/plus reach
(extra length supports V-Twin applications)
• 12" flex hose -12 mm standard reach
• 12" flex hose -10 mm standard reach
• Rugged blow molded hard case with removable lid
• Repair parts kit
No. 5604 – Motorcycle compression tester kit.
Wt., 3 lbs., 14 oz.
5604
Deluxe Compression Tester Kit
Complete with standard and specialty adapters, this deluxe
kit offers a complete package for compression testing on
gasoline engines. Kit includes the deep well connector used
on recessed plug well style heads and the new Ford Triton™
engine adapter using 16 mm thread plugs.
Functions and Features:
• Corrosion resistant nickel plated finish
• Adapters work on both flat and tapered seat plugs
• Extra long 25" flex hose gauge assembly with quick coupler, allows easy viewing out of cluttered engine compartment
• 2-1/2" gauge features chrome bezel and rugged
protective outer boot
• Dual scale gauge reads 0-300 psi and 0-2100 kPa
• 8" deep well 14 mm connector
• 5" flex Ford Triton™ 16mm adapter • 12" flex-14 mm standard reach
• 12" flex-14 mm long reach
• 10 mm, 12mm, and 18 mm thread adapters
• Rugged b low molded hard case with removable lid
• Repair parts kit
No. 5605 – Deluxe compression tester kit. Wt., 4 lbs., 10 oz.
5605
Ford Triton is a Registered Trade
Mark of the Ford Motor Company.
123
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Cylinder Leakage Tester Kit
5609
Quickly diagnose internal engine problems such as bad rings,
valves and leaking head gaskets. Kit come complete with
adapters for most applications.
Features and benefits:
• Dual 2-1/2" gauges feature chrome bezel and rugged
protective outer boot.
Scales
read 0-100 psi and 0-700 kPa.
•
• Pressure regulated manifold includes quick couplers.
• Long flex 24" 14 mm hose.
• 10 mm, 12 mm and 18 mm thread adapters.
• Blow molded hard case with removable lid.
• Detailed instruction chart.
No. 5609 – Cylinder leakage tester kit. Wt., 4 lbs.
Transmission/Engine Oil Pressure Kit
The 5610 professional kit can be used for domestic and import
applications. High and low pressure gauges make this kit useful for both transmission and engine work. Kit comes complete
with adapter for most applications. Designed to be used for both
static and on road testing.
Features and benefits:
• Large 3-1/2" gauges feature a chrome bezel and rugged
protective outer boot.
• Low pressure gauge reads 0–100 psi and 0–700 kPa.
• High pressure gauge reads 0–400 psi and 0–2800 kPa.
• Both gauges include rear hook to allow gauge to be hung
conveniently out of the way.
• Gauges and hose assembly incorporate quick couplers for
easy disconnect.
• Kit includes 13 adapters and a detailed instruction manual.
• Blow molded hard case with removable lid.
No. 5610 – Transmission/engine oil pressure kit. Wt., 5 lbs., 3 oz.
5610
Vacuum/Pressure Gauge Kit
5613
124
The 5613 is deal for testing vacuum lines and components.
Accurately tests low-pressure fuel systems. Quickly diagnose
internal engine problems such as bad rings, valves and leaking
head gaskets. Kit comes complete with adapter for most applications. Pin point hard to find problems such as cracked lines,
PCV, fuel pump, fuel filters and more.
Features and benefits:
• Large 3-1/2" gauge features a chrome bezel and rugged
protective outer boot.
Dual
purpose gauge reads vacuum and pressure.
•
Dual
scale gauge reads 0-30 in. Hg vac and 0-70 cm Hg,
•
also reads 0-15 psi and 0-100 kPa.
• Built in rear hook allows gauge to be hung at eye level.
• Adapters for most applications.
• Blow molded hard case with removable lid.
• Detailed instruction chart.
No. 5613 – Vacuum/pressure gauge kit. Wt., 3 lbs.
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Universal Overhead Valve Spring Compressor
• Permits removal and installation of valve springs without
removing the cylinder head on many cars and light trucks.
Durable steel construction.
• Spring loaded offset jaws easily grip and compress valve springs.
No. 4573 – Universal overhead valve spring compressor.
Wt. 1 lb.
4573
Large Valve Spring Compressor
• Designed to compress valve springs on overhead valve
engines.
• Includes two valve spring adapters, which fit valve spring
retainers up to 1" (25 mm) and 1-3/16" (30 mm).
• Unique, direct action compressor lever gives better
visibility of valve spring retainers located in difficult access
areas.
• Jaw opening of 1-3/8" to 5-5/8" (35 mm to 142 mm);
throat clearance of 5-7/8" (150 mm).
No. 4572 – Large valve spring compressor. Wt. 5 lbs.
4572
Honda / Acura Crankshaft Damper Holding Tool
• Tool allows the technician to hold the crankshaft damper
when tightening or loosening the crankshaft bolt.
•50mm hex on holding tool.
•Works on the following Honda and Acura engines:
1990–1997 Honda Accord 2.2L 4 cyl.
1996–1997 Honda Accord 2.7L V6
1998–newer Honda Accord 2.3L 4 cyl. & 3.0L V6
1992–newer Honda Civic 1.6L 4 cyl.
1997–newer Honda CR-V 2.0L 4 cyl.
1993–1997 Honda Del Sol 1.6L 4 cyl.
2000–newer Honda Insight 1.0L 3 cyl.
1995–1997 Honda Odyssey 2.2L 4 cyl.
1998 Honda Odyssey 2.3L 4 cyl.
1999–newer Honda Odyssey 3.5L V6
1992–newer Honda Prelude 2.2L 4 cyl.
1992–1996 Honda Prelude 2.3L 4 cyl.
2000–newer Honda S2000 2.0L 4 cyl.
1997 Acura CL 2.2L 4 cyl.
1997–1998 Acura CL 3.0L V6
1998–1999 Acura CL 2.3L 4 cyl.
2000–newer Acura CL 3.2L V6
1990–1992 Acura Integra 1.6L 4 cyl.
1992–1993 Acura Integra 1.7L 4 cyl.
1993–newer Acura Integra 1.8L 4 cyl.
1991–1995 Acura Legend 3.2L V6
1996–newer Acura RL 3.5L V6
1995–newer Acura TL 3.2L V6
4731
No. 4731 – Honda/Acura crankshaft damper holding tool.
Flange Puller
Pulls harmonic balancers, timing gears, and parts having
two or three tapped holes. Slotted holes in puller body
permit cap screws to be positioned to handle bolt circle
diameters from 1/2" to 4-5/8". Reach of puller is 4-1/4".
Includes three cap screws (3/8"–24 x 3"), and three cap
screws (3/8"–16 x 3").
No. 6930 – Flange puller. Wt., 3 lbs. 4 oz.
6930
125
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Flange-Type Puller Set – 48 Piece
• Versatile puller capable of removing a wide variety of
components having tapped pulling holes, including harmonic
balancers, gears, crankshaft pulleys, etc.
• Capable of handling 2- or 3-way bolt pulling applications.
• Works on many cars, pickups, SUVs, and small engines.
• Carries the OTC Lifetime Marathon Warranty® against defects
in workmanship and material.
Contents of set:
• Puller flange: adapts to bolt circle dia. of 1-1/2" to 4-5/8".
• Forcing screw: 5-5/8" lg., 5/8-18 thread.
• Shaft protector: 1-3/16" dia. x 3/4" thick.
• Three each of the following flat washers: 1/4"; 5/16"; 3/8".
• Three each of the following bolt sizes:
3/8"-16 x 3" lg.
1/4"-28 x 3" lg.
3/8"-16 x 4-1/2" lg.
5/16"-24 x 3" lg.
M8 x 1.25 x 45 mm lg.
5/16"-18 x 3-1/2" lg.
M8 x 1.25 x 65 mm lg.
5/16"-18 x 6" lg.
M8 x 1.25 x 90 mm lg.
3/8"-24 x 1-1/2" lg.
M10 x 1.5 x 35 mm lg.
3/8"-16 x 2" lg.
No. 7790 – Flange-type puller set – 48 piece. Wt., 7 lbs., 3 oz.
7790
Flange-Type Puller Set
• Covers almost every car, pick-up, SUV, and small engine.
• Capable of handling almost every two- or three-way bolt pull
6294
possible.
• For use on a variety of jobs: harmonic balancers, steering
wheels, crankshaft pulleys, and gears.
• OTC Lifetime Marathon Warranty® covers defects in
workmanship or materials.
• Storage tray and detailed application chart included.
• Slotted holes in puller flange permit cap screws to be
positioned to handle bolt circles from 1-1/2" to 4-1/4".
Contents of set:
•Three each of the following washer head bolts (Grade 8): M8 x 1.25 x 90 mm M8 x 1.25 x 45 mm 1/4-28 UNF x 3" M8 x 1.25 x 65 mm 5/16-18 UNC x 3.5" 5/16-24 UNF x 3"
3/8-24 UNF x 1.5"
3/8-16 UNC x 2"
3/8-16 UNC x 3" 3/8-16 UNC x 4.5" M10 x 1.5 x 35 mm
•Special stepped bolts– 1990–2002 GM 3300-3800 V6 crankshaft pulleys.
•Two forcing screws: 6" long and 3" long.
•Two pointed forcing screw center tips.
•Two flat forcing screw center tips.
No. 6294 – Flange-type puller set. Wt., 6 lbs., 13 oz.
Master Harmonic Balancer Installer
• 11 special adapters make this a complete master harmonic
126
6505
balancer installer set for most car and light truck applications.
• The heavy-duty 7/8" diameter forcing screw has internal
threads to fit the threaded adapters.
• Plastic storage tray keeps set components organized for
easy selection.
No. 6505 – Master harmonic balancer installer.
Wt., 2 lbs., 13 oz.
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Harmonic Balancer Puller/Installer Set
• For easy removal of most harmonic balancers and drive
pulleys which are press-fitted onto the crankshaft. A
bearing-centered circular 2/3-way puller flange and an
assortment of metric and fractional bolts and adapters
provide wide coverage.
• A heavy-duty, 3/4" dia. forcing screw is internally threaded
to fit the eight adapters to install harmonic balancers.
Adapter sizes included: M16 x 2.0, M14 x 1.5, M12 x 1.5,
3/4"-16, 5/8"-18, 9/16"-18, 1/2"-20 and 7/16"-20.
• A blow-molded plastic storage case keeps set contents
organized and protected from loss.
No. 4531 – Harmonic balancer puller/installer set.
Wt., 8 lbs., 13 oz.
4531
BMW Head Bolt Socket
• Socket is designed to fit in the cylinder head on M42 and
M50 engines to remove and install cylinder head bolts.
• Spring loaded detent ball holds bolt in place.
• Works with 1/2 inch ratchet, breaker bar, or torque wrench.
• Socket size is E12 for external TORX® bolts.
No. 5940 – BMW head bolt socket. Wt., 8 oz.
5940
Toyota Head Bolt Socket
• Specially designed socket is needed to tighten or loosen
head bolts on Toyota Paseo vehicles with 3S-GE and
3S-FE engines.
• 8 mm socket features a 12-point, 1/2 inch drive socket.
No. 6022 – Toyota head bolt socket. Wt., 13 oz.
6022
Similar to Toyota
No. 09043-50080
Universal Pulley Holder
• Universal design fits many different size pulleys having
slots or holes, such as camshaft pulleys or crankshaft
pulleys.
• Wrench is adjustable from 1-1/2" to 8-5/8"; four different
size step pins are interchangeable.
• Long handle enables technician to easily hold the pulley when tightening or loosening retaining bolts.
No. 4754 – Universal pulley holder. Wt., 4 lbs., 15 oz.
4754
Serpentine Belt Tool
• Fits tensioner pulleys with 13 mm–16 mm, 18 mm
hex or 3/8" and 1/2" square drives.
• For hard to access tensioners; there are 13 mm and
15 mm 12-point wrenches built into the handle.
• 13 mm, 14 mm and 15 mm crows foot wrenches also
included.
No. 4645 – Serpentine belt tool. Wt., 4 lbs., 13 oz.
4645
127
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Engine Preluber Kit
• Ensures oil is present to internal engine components on
6492
the first start of a new or rebuilt engine, or after major
engine work is performed.
• Required to prime the oil pump and fill the oil galleries and
internal engine components with clean, new oil.
• Connects to engine oil system at the oil pressure sensor
on a variety of domestic and import engines.
• Oil pressure sensor adapters included.
No. 6492 – Engine preluber kit. Wt., 2 lbs., 5 oz.
Variable Pin Spanner Wrench
• Universal design fits many different types of pulleys
6613
having slots or holes, including camshaft pulleys and
crankshaft pulleys.
• Wrench is adjustable from 1-1/4 inch to 5 inches; works
with a 1/2 inch drive ratchet or breaker bar.
Replacement Parts:
526908-5....... 6 mm pin
526908-1....... 3.5 mm pin
526908-2....... 4 mm pin
526908-6....... 7 mm pin
526908-3....... 4.5 mm pin
526908-7....... 10 mm pin
526908-4....... 5 mm pin
526908-8....... Handle
No. 6613 – Variable pin spanner wrench. Wt., 2 lbs.
Belt Installation Tool
7654
With this tool and the correct serpentine belt tool for the job,
installing those almost impossible serpentine belts is a lot
less frustrating and time-consuming. The two-pin hook end
holds the belt for precise placement, and the handle gives
you the grip you need to maneuver it around the pulleys
easier. It’s also a handy tool to have around for installing
V-belts and timing belts that are never in easy-to-reach
places. 25" long.
No. 7654 – Belt installation tool. Wt., 10 oz.
Ford Halfshaft Remover/Differential Rotator
7140
128
No. 7140 is essential when removing the left-hand ­halfshaft
from Escort/Lynx transaxles. It ensures correct removal and
allows the technician to turn the ­differential.
No. 7140 – Ford halfshaft remover/differential rotator.
Wt., 1 lb., 13 oz.
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Delco Alternator Insulator Wrench
Getting the positive battery wire off the back of Delco alternators should be a quick and easy job. But if you turn the
nut holding the battery wire and don’t keep the terminal
stud from twisting, there’s a good chance the insulator will
break. Keep a simple job simple with the No. 7780 insulator
wrench. It steadies the insulator block on new Delco CS and
older Delco SI alternators found on many GM vehicles (1972
and newer), and 1975–90 AMC and Jeep vehicles.
No. 7780 – Delco alternator insulator wrench. Wt., 3 oz.
7780
Frost Plug Installer Set
• Designed to install frost plugs in liquid-cooled gas and
diesel engines found in automobiles, trucks, SUVs,
agricultural equipment, and construction equipment.
• Simply use an air hammer with the driver and appropriate
disc to install frost plugs ranging from 1" to 2-1/16" in
diameter.
Set contains: No. 4604-1 Driver (14" lg.); No. 4604-2 Frost
Plug Disc Set (3 qty.).
No. 4604 – Frost plug installer set. Wt., 1 lb., 13 oz.
4604
Frost Plug Remover/Installer Set
• Designed to remove and install frost plugs used in liquid-
cooled gas and diesel engines found in automobiles,
trucks, SUVs, agricultural equipment, and construction
equipment.
• Simply use a hammer with the driver and appropriate disc
to install frost plugs ranging from 1" to 2-3/8" in diameter.
Set contains: No. 4603-1 Installer Handle (18" lg.);
No. 4604-2 Frost Plug Remover; No. 4604-3 Frost Plug Disc
Set (7 ea., plus 1 retaining nut).
No. 4603 – Frost plug remover/installer set. Wt., 6 lbs.
4603
Glow Plug Remover
Set includes 10 mm and 12 mm split nuts, three spacers
(3/16", 1/4", and 5/16"), plastic storage/organizer case and
instructions. The 10 mm split nut will work on Ford 6.9L and
7.3L diesels; GM 5.7L, 6.2L, and 6.5L diesels; and various
diesels in import vehicles. The 12 mm split nut works on
various diesels in import vehicles, plus many agricultural
and construction diesel applications.
No. 6005 – Glow plug removal tool. Wt., 5 oz.
6005
Fuel Injector Nozzle Puller
• Pulls fuel injection nozzles on Ford 6.9L/7.3L and
Navistar DT466/9L diesel engines.
• Slide hammer action gives an even, straight pull on the
nozzle for fast, easy removal.
• Puller nut screws onto injector nozzle inlet port.
No. 7454 – Fuel injector nozzle puller. Wt., 1 lb., 15 oz.
7454
129
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Diesel Compression Tester with Adapters
5020
Similar to
Ford No. 303-D091
(D93T-6000-A)
Easy-to-use compression tester is designed specifically
for medium-duty diesel engines equipped with glow plugs.
Dual reading gauge measures compression to 1000 psi
and 7000 kPa. Gauge has a push-button release valve and
quick disconnect fittings on the hose end. Tester comes with
all the necessary glow plug and nozzle adapters in a handy
storage case.
Tester services these engines:
• Cummins B and C
• Navistar DT466/DT360
• Ford/Navistar 6.9 & 7.3L
• GM 6.2L and 6.5L
• Hino diesel and Mitsubishi Fuso truck engines
No. 5020 – Diesel compression tester with adapters.
Wt., 7 lbs., 13 oz.
Replacement Adapters (available separately):
No. 47484 – Hino diesel truck engines with 12 mm x
1.25 threads.
No. 209633 – Ford 6.6L & 7.8L diesels.
No. 217791 – Cummins B & 5.9L.
No. 308472 – Mitsubishi Fuso truck 4D & 6D engines with 10 mm x 1.25 threads.
No. 310810 – Cummins C.
No. 310832 – Ford/Navistar 6.9 & 7.3L, Detroit 6.2L
with 10 mm x 1.0 threads.
No. 310840 – Navistar DT466/DT360.
Universal Diesel Engine Compression Gauge
5021
Similar to
Ford No. 303-D092
(D93T-6000-B)
Works on any diesel engine to test compression up
to 1000 psi and 7000 kPa. Features include a check
valve, push button compression release, and a quick
disconnect fitting on the hose end. Straight and 45° hose
connectors are included.
No. 5021 – Universal diesel engine compression gauge.
Wt., 1 lb., 8 oz.
No. 304802 – Replacement gauge. Wt., 8 oz.
Ford Diesel Compression Test Adapter
When the glow plug is removed from the cylinder, this
adapter is used to connect the No. 5021 gauge to perform
a compression test.
• Works on 1994–newer Ford vans and pickups with 7.3L
direct-injected turbocharged (DIT) diesel engine.
No. 6076 – Ford diesel compression test adapter. Wt., 5 oz.
6076
Compression Tester
•
6660
130
Use with OTC No. 5021 diesel engine compression gauge.
• Works on 2003-2006 Ford vans and trucks with 6.0L
diesel engines.
No. 6660 – Compression tester. Wt., 7 oz.
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Ford Rear Main Oil Seal Kit
• Works on 1994–2003 7.3L diesel engine in Ford 3/4- and
1-ton trucks.
• A complete kit with the tools you need to correctly remove
and install the rear main oil seal and wear ring on the
crankshaft.
• Eliminates makeshift methods of seal removal and
installation that could damage the new seal or crankshaft.
No. 7835 – Ford rear main oil seal kit. Wt., 7 lbs.
7835
Ford 5-pin Connector Harness for Glow Plug
Testing
• Provides an easy way to check glow plug resistance
without having to remove the valve cover of 1994–98 Ford
trucks and vans with 7.3L DIT (direct-injected
turbocharged) diesel engines.
• Used with any standard digital volt ohmmeter to check
glow plug resistance.
No. 6088 – Ford 5-pin connector harness for glow plug
testing. Wt., 3 oz.
Ford 9-pin Connector Harness for Glow Plug
Testing
• Permits testing glow plug resistance without having to
6088
6089
remove the valve cover of 1998-1/2 thru 2003 Ford trucks
and vans with 7.3L DIT (direct-injected turbocharged)
diesel engines.
• Use with any standard digital volt ohmmeter to check
glow plug resistance.
No. 6089 – Ford 9-pin connector harness for glow plug
testing. Wt., 4 oz.
Ford Oil Line Disconnect Tool for 6.0 L
• Use to disconnect the high-pressure oil rail supply line from
the fuel rail when removing fuel injectors.
• Works on the 6.0: diesel engine found in 2003–newer F-250,
F-350, F-450, and F-550 trucks, and Ford Excursions.
No. 6594 – Ford oil line disconnect tool for 6.0 L. Wt., 5 oz.
Similar to
Ford No. 303-755
6594
131
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Ford High Pressure Oil Line Disconnect Tool
6595
Similar to Ford
303-625
• Use to disconnect the high pressure oil line from the
cylinder head.
• Works on 1998 - 2003 Ford vans and trucks with 7.3L
direct-injected, turbo-charged (DIT) diesel engines.
No. 6595 – High pressure oil line disconnect tool.
Wt., 3 oz.
Ford Injector Remover / Installer Kit
• Removes and installs injectors without damaging the
Similar to Ford
No. 303-491
No. 303-492
6067
Similar to
Miller No. 8318
6069
injector or cylinder head.
Application: 1994–2003 Ford 3/4- and 1-ton trucks,
Super Duty trucks, and vans with 7.3L directinjected turbocharged (DIT) diesel engine.
No. 6067 – Ford injector remover/installer kit.
Wt., 6 oz.
Cummins Diesel Fuel Injector Remover Kit
Kit contains a fuel injector connector tube remover and fuel
injector puller. The fuel injector connector tube must be
removed before removal of the injector, or both will be
damaged.
Application: 1998-1/2–2002 Dodge pickups and vans with
5.9L 24-valve Cummins diesel turbo engine.
No. 6069 – Cummins diesel fuel injector remover kit.
Wt., 8 oz.
GM Injection Pump Wrench Set
Similar to
Kent-Moore J-41089
6087
Similar to
Kent-Moore J-41711
5060
132
• Use to loosen or tighten injection pump retaining bolts
whenever pump timing adjustment or pump service is
required. Services 1996–1999 GM full-size 2- and
4-wheel drive trucks, vans, and Suburbans with 6.5L
diesel engine.
• Two specially bent wrenches are needed, due to the
location of the throttle, cruise control, T.V. cable bracket,
cooling system crossover pipe and bracket, and the
thermostat housing on vans and pickups.
• Wrenches are 15 mm, 12-point, double box-end type.
No. 6087 – GM injection pump wrench set. Wt., 1 lb.
Detroit Diesel Injector Socket
Used on GM 6.2L and 6.5L engines. This 30 mm socket
ensures proper fit during nozzle removal and installation.
The 3/8" square drive and 7/8" hex permit easy
access in tight quarters, and prevent damage
to nozzle and related components.
No. 5060 – Detroit diesel injector socket. Wt., 8 oz.
AUTOMOTIVE SPECIAL TOOLS
Engine Service
Cummins Engine Barring Tool
Need to manually rotate an engine? This tool makes the
job easy. Just insert the tool into the flywheel housing until
it engages the ring gear, then attach a 1/2" square drive
ratchet or breaker bar and turn. The tool’s load-bearing collar
provides friction-free operation while rotating the tool in the
housing.
• Works on Cummins B and C series diesel engines and
5.9L liter diesels used in Dodge pickups.
No. 7471A – Cummins engine barring tool. Wt., 11 oz.
7471A
Master Cummins Diesel Fuel Injection Test Kit
Includes the fittings and gauge needed to check fuel
pressure, fuel volume, and fuel restrictions from the
delivery pump to the injection pump.
Contents:
No. 518501 - Special quick-disconnect banjo fitting
(M14 x 1.5 male).
No. 7915 - Two fuel injection quick-coupler adapters.
No. 518493 - Quick-disconnect banjo fitting (M12 x 1.5
male).
No. 223336 - Gauge assembly.
No. 6082 - Fuel volume test adapter.
No. 6078 - Diesel fuel inlet restriction test adapter.
• For 1988–98 Dodge pickups and vans with 5.9L 12-valve,
and 1998-1/2–newer 5.9L 24-valve Cummins diesel
engines.
No. 6080 – Master Cummins diesel fuel injection test kit.
Wt., 5 lbs.
6080
Cummins Diesel Fuel Volume Test Adapter
Used to perform fuel volume test of fuel transfer pump.
Fuel volume is as important as fuel pressure. Pump may
pass pressure test, but fail volume test. No. 6082 fitting is
threaded into transfer pump. The end of the 2 ft. tubing
is placed into a container for fuel to be measured.
This adapter is included in OTC Master Kit No. 6080.
Application: 1994–1998-1/2 Dodge pickups and vans with
5.9L 12-valve Cummins diesel engine.
6082
No. 6082 – Cummins diesel fuel volume test adapter.
Wt., 3 oz.
Special Quick-Disconnect Banjo Fitting
Adapter fitting (M14 x 1.5 male) is used to check fuel
pressure from the delivery pump to the injection pump.
Used with gauge assembly of OTC set No. 6079. Has
quick-connect schrader valve on end of fitting for safety and
ease of hook-up to gauge. Included in OTC kit No. 6080.
Application: 1996–1998-1/2 Dodge pickups and vans with
5.9L 12-valve Cummins engine.
No. 518501 – Special quick-disconnect banjo fitting.
Wt., 3 oz.
518501
133
AUTOMOTIVE SPECIAL TOOLS
Coolant Exchange
Works o
n both p
ressuriz
e
non-pre d and
ssurized
cooling
systems
Coolant Exchange Unit
Designed with the user in mind.
Increase Your Profits
• Our 10-minute exchange process means no more
waiting for the engine to warm up!
Safety First
• Our “engine off” feature removes pulleys, belts, and fan
blades from the safety equation.
• No additional ventilation required.
• Vacuum mode creates a “push/pull” exchange process
allowing the technician to safely remove high pressure
in a hot system.
• “Hands-off” transfer of used coolant to a bulk tank
prevents spills and helps protect the technician.
Simple to Operate
• Two clearly marked valves and an easy-to-read gauge
make this machine very simple to use.
• Sight glass clearly shows the amount of coolant in the
waste tank.
• One valve controls the flow of coolant; process is easy
to understand—no special training needed.
• No electricity required. 90 psi shop air drives the
exchange process, as well as the 2 gpm pump on the
waste tank.
10-Minute Exchange Process
Back View:
7-gallon capacity
supply tanks allow
storage of different
coolants.
Designed to Survive
• Impact-resistant polypropylene cabinet will not scratch
or dent vehicle.
• Cabinet is impervious to chemicals commonly used in
the shop.
• Large, inflatable tires carry a well-balanced platform
easily across any shop floor.
• Easy to maneuver between bays and vehicles.
75700
Specifications:
Power Supply – 90 psi shop air
Tanks– Internal waste – 15-gallon capacity
– External supply (2) 7-gallon capacity (removable)
Dimensions: 47" H x 26" W x 33" D (119 cm x 66 cm x 84 cm)
Medium Step Adapter. . . . . . . . . . . . . . . . . . . . . Two included;
fits hose size 1-1/4", 1-3/8", and 1-1/2"
Large Step Adapter . . . . . . . . . . . . . . . . . . . . . . Two included;
fits hose size 1-3/4", 2", and 2-1/4"
134
Extra Design Features
• Two external new coolant supply tanks allow on-board
storage of two different coolant types.
• Graduations on tanks show user the amount of new
coolant on board.
• On-board storage of step adapters.
• Adapter kit included.
• No hoses to cut.
• 96" hoses can be neatly stored on unit.
• One-year warranty.
No. 75700 – Coolant exchange unit. Wt., 180 lbs.
No. 75115 – Replacement coolant 5-gallon tank.
No. 75360 – Heavy-duty adapter kit. Links the two tanks
for 14 gal. capacity to service class A vehicles. (Note:
must have 7-gallon tank No. 75370).
No. 75370 – Replacement coolant 7-gallon tank.
No. 17490 – Protect your investment with a heavy-duty
vinyl dust cover. Features corded seams for durability;
medium gray color with CoolTech logo.
AUTOMOTIVE SPECIAL TOOLS
Coolant Service
Coolant and Battery Refractometer
This can be used for measuring the freezing point of either
propylene and ethylene glycol based cooling systems. It can
also be used for checking the strength of electrolyte solution
in batteries. This precision instrument features high quality
optics with ultra smooth focusing on the body. Coolant scale
range: 32° F/0° C to -60° F/ -51° C.
No. 75240 – Coolant and battery refractometer (C & F
scales). Wt., 12 oz.
75240
Econo-Clean Coolant Service Accessories
To ensure coolant will provide adequate protection to the
vehicle, the coolant should be adjusted to the manufacturer’s specifications. These accessories will help you
quickly test coolant.
No. 75133 – Pocket pH pen — Quickly shows the pH of the
coolant, whether used or recycled. Wt., 7 oz.
No. 75134 – Coolant test strips — Just dip a strip in coolant
and it shows the freeze point and the pH; bottle of 50 strips.
Wt., 15 oz.
No. 75234 – 3-way heavy-duty truck coolant test strips –
shows pH, freeze point, and nitrite (0–4000 ppm), pH
<7.5–11+, glycol 0-60%. Wt., 1 lb.
75133
75234
75134
Coolant Refiller
• 26" Hg vacuum refills cooling system without air lock.
• Eliminates the need for “bleeding.”
• Checks for system leaks and utilizes OEM approved
technology.
• Universal “fits all” cone adapter.
• Built-in gauge protector.
No. 75260 – Coolant refiller. Wt., 1 lb., 12 oz.
75260
Radiator Coolant Dye
• Pinpoint leaks in radiators, hoses/fittings, water pumps, and head gaskets.
• Extended-life dye is specifically formulated for use in
extended-life coolants. This eliminates the color distortion problem found in the existing regular radiator coolant dye
when mixed with extended-life coolant.
• Extended-life dye is for use with red, orange, or yellow
extended-life coolants.
• Each bottle services one vehicle.
No. 16266 – Extended-life radiator coolant dye.
Six (1 oz./30 ml) bottles. Wt., 8 oz.
No. 16255 – Standard radiator coolant
dye. Six 1/4 oz. (7.5 ml) bottles.
Wt., 4 oz.
16266
16255
135
AUTOMOTIVE SPECIAL TOOLS
Coolant Service
Cooling System Pressure Tester
7991
Now you can pressure test the cooling system on most cars,
light commercial trucks, motorcycles, and even marine
applications. The tester’s universal fit eliminates the need
for multiple adapters.
Note: Will not work on Saturn and Kia cars or Jeep with
the plastic reservoir.
No. 7991 – Cooling system pressure tester.
Wt., 3 lbs., 2 oz.
No. 70600-96 – Replacement bladder.
Wt., 1 oz.
Hose Clamp Pliers Set (2 piece)
• Includes a cross-slotted jaw pliers and a wide,
4502
flat-band
hose clamp pliers. Services most ring-type or flat-band
hose clamps.
• The clamps are held open with a ratchet locking
mechanism. Jaws swivel to access hose clamps in any
position.
No. 4502 – Hose clamp pliers set. Wt., 1 lb., 3 oz.
Hose Clamp Pliers Set
• Contains five different styles of hose clamp pliers, which
will service most flat-band and ring-style hose clamps.
Also contains a hose removal tool.
Set Contains:
• Straight hose clamp pliers set
• Hose removal tool
• Flat-type hose clamp pliers
• Offset hose clamp pliers
• 45° hose clamp pliers
No. 4496 – Hose clamp pliers set.
Wt., 3 lbs., 13 oz.
4496
Vacuum Hose and Fuel Line Removal Tool
• Designed to remove vacuum hose or fuel lines (3/16" to
1/2") from fittings or tubing.
• Simply place the black jaw on the fitting or tubing – the
jaw will grip the material. Then use the silver jaw to push
the vacuum hose or fuel line off the fitting or tube.
4522
136
No. 4522 – Vacuum hose and fuel line removal tool.
Wt., 3 oz.
AUTOMOTIVE SPECIAL TOOLS
Coolant Service
Offset Hose Clamp Pliers
• Head is offset from handle to allow access to hard-to-
reach clamps.
• Swivel jaws allow pliers to be used on many different
flat-band and ring-type hose clamps.
No. 4523 – Offset hose clamp pliers. Wt., 5 oz.
4523
45° Hose Clamp Pliers
• Jaws are bent at a 45° angle and pliers tips swivel to
allow easy access to confined areas.
• Ratchet lock mechanism holds jaws open.
• Works on most flat-band hose clamps.
No. 4524 – 45° hose clamp pliers. Wt., 5 oz.
4524
Flexible Hose Clamp Pliers
• Allows technician to access the flat-type hose clamps
located in hard-to-access areas.
• Pliers has locking mechanism to hold clamp in the open
position – makes removal and installation of clamp much
easier.
• Heavy-duty, 24" cable flexes to almost any position.
No. 4525 – Flexible hose clamp pliers. Wt., 5 oz.
4525
Hose Removal Tool
• Unique tip easily fits between hose and fitting to break
stubborn hoses loose.
• Large handle provides a good grip on tool during hose
removal.
• Works on radiator hoses, heater hoses, transmission lines
– any place a rubber hose is clamped to a fitting.
No. 4521 – Hose removal tool. Wt., 7 oz.
4521
137
AUTOMOTIVE SPECIAL TOOLS
Water Pump & Multipurpose Cleaning Gun
GM Water Pump Socket
6060A
6046
Similar to
Kent-Moore J-43181
• Works on 1993–newer Cadillac 4.6L V8 Northstar engine,
and 1995–1999 Oldsmobile Aurora 4.0L V8.
• 1/2" sq. drive for use with 1/2" drive breaker bar or
ratchet.
• Tool is designed to self-center in the water pump housing,
allowing the tangs to fully engage the water pump for
removal or installation.
No. 6060A – GM water pump socket. Wt., 2 lbs., 10 oz.
GM Heater Line Quick-Connect Release Tool
• Specially designed for separating quick-connect fittings on
heater lines of 1999–2006 Chevy and GMC C/K trucks.
• Tool snaps around the hose and simultaneously
depresses the locking tabs to disengage the fitting.
No. 6046 – GM heater line quick-connect release tool.
Wt., 2 oz.
Similar to Ford
No. 303-249
(T92P-70010-AH)
7784
Ford Gear-Position Sensor Adjuster
When you’re adjusting the manual-lever position sensor on
a Ford automatic transmission, this tool gets the detent
setting right the first time.
• For use on E40D, AXOD-E, AX4N, AX4NS, C6, and
AOD-E automatic transaxles and transmissions.
No. 7784 – Ford gear-position sensor adjuster.
Wt., 2 oz.
“Blast-Vac” Multipurpose Cleaning Gun
• Perfectly suited for quick and efficient cooling system
6043
138
flushing. Simply attach it to radiator or heater hoses and
you’re in business.
• Also usable in washing engines and even shop floors.
• Two simple connections: one to shop air and one to a
typical water faucet.
• No. 6043 creates a unique vortex air/water blast for
powerful cleaning applications.
• The tool can also be used to vacuum by turning the
venturi inside the gun in the opposite direction. Air flow
is reversed to create a strong vacuum.
Note: While normal water pressure will handle the
majority of a cooling system flush, short blasts are
sometimes needed to loosen some contaminants from
within the system.
No. 6043 – “Blast-Vac” multipurpose cleaning gun.
Wt., 13 oz.
AUTOMOTIVE SPECIAL TOOLS
Fan Clutch Service
Fan Clutch Wrench Master Set
Conventional wrenches are just too wide for the job of
removing the fan clutch assembly on some engines.
Here’s the solution: You hold the fan clutch stationary with
the clutch holder tool, and turn the fan clutch nut with the
special wrench. Most wrenches feature a square drive for
attaching a breaker bar for extra torque. Time savers when
replacing water pumps, or for any other front engine service
in body or repair shops. Holding tools and wrenches are
available individually and in sets (see chart on next page).
No. 7885 – Fan clutch wrench master set – Includes all
individual components except Nos. 7925-1, 7925-2, and
6068. Includes molded carrying case. Wt., 16 lbs.
7885
Individual Holding Tools, Wrenches, and Sets
Individual Components
No. 7204E1 – Holding tool. 2-1/4" (57 mm). Wt., 14 oz.
No. 7204E2 – Wrench. 1-7/16" (36 mm). Wt., 1 lb., 14 oz.
No. 7205E1 – Holding tool. 3-1/4" (82 mm). Wt., 1 lb., 8 oz.
No. 7205E2 – Wrench. 1-7/8" (47 mm). Wt., 3 lbs., 10 oz.
No. 6068 – Wrench. 1-7/8" (47 mm). Wt., 2 lbs., 8 oz.
No. 7818 – Holding tool. 2-1/8" (54 mm). Wt., 1 lb., 8 oz.
No. 7823 – Wrench. 1-9/16" (39 mm). Wt., 1 lb., 11 oz.
No. 7855 – Holding tool. 2-3/8" (60 mm). Wt., 14 oz.
No. 7887 – Holding tool. 3" (76 mm). Wt., 1 lb., 8 oz.
No. 7925-1 – Wrench. 2" (51 mm). Wt., 2 lbs.
No. 7925-2 – Holding tool. 2-1/4" (57 mm). Wt., 2 lbs., 5 oz.
Sets:
No. 7204E Set – (7204E1 & 7204E2). Wt., 2 lbs., 8 oz.
No. 7205E Set – (7205E1 & 7205E2). Wt., 4 lbs., 13 oz.
No. 7817 Set – (7205E2 & 7818). Wt., 4 lbs., 10 oz.
No. 7854 Set – (7204E2 & 7855). Wt., 2 lbs., 8 oz.
No. 7925 Set – (7925-1 & 7925-2). Wt., 4 lbs., 5 oz.
Ford Diesel Fan Clutch Wrench
• Designed for use with OTC No. 7205E1 holding tool to
remove fan clutch assembly.
Has the same size opening as the OTC No. 7205E2
wrench, but has a special bend in the handle to provide
clearance for accessories found on some vehicles.
Application: 1998–2003 Ford vans and pickups with 7.3L
direct-injected turbocharged (DIT) diesel engine.
Similar to
Ford 303-591
6068
No. 6068 – Ford diesel fan clutch wrench. Wt., 2 lbs., 2 oz.
139
AUTOMOTIVE SPECIAL TOOLS
Fan Clutch Service
Individual Holding Tools, Wrenches, and Sets
Year
Make /
Model
Engine
U.S. Size Metric Size
1983–1993 Ford /
6.9L, 7.3L Diesel
F-Series Truck, E-Series Van
1984–1991 Ford /
4.9L Inline 6
F-Series Truck, E-Series Van
1987–1997 Ford /
5.0L, 5.8L, 7.5L V8
F-Series Truck, E-Series Van
1992–1996 Ford /
4.9L Inline 6
F-Series Truck, E-Series Van
1994–1997 Ford /
7.3 D.I. Diesel
F-Series Truck, E-Series Van
1983–1989 Ford / 2.8L, 2.9L V6
Ranger, Bronco II
1990–2004 Ford / 4.0L V6
Ranger, Explorer, Bronco II
1998–2003 Ford /
7.3 DIT Diesel
F-Series Truck, E-Series Van
1988–2004 Dodge /
5.9L Diesel
Full Size Pickup, Full Size Van
1992–2004 Dodge /
3.9L V6, 5.2L, 5.9L V8
Dakota, Ram Pickup, Ram Van
8.0L V10
1993–1998 Jeep /
5.2L V8
Grand Cherokee
1996–2004
GM /
Full Size Pickup, Full Size Van,
Astro / Safari Vans, S-Truck,
Blazer / Jimmy, Yukon / Tahoe
4.3L V6
5.0L, 5.7L V8
1994–1999 Navistar / 466
medium-duty trucks and school buses
3-1/4"
1-7/8"
OTC
Tool No.
OTC Tool Set
Global
Number
Ford
Tool No.
82 mm
47 mm
7205E1
7205E
7205E2
303-213
303-214
T83T-6312-A
T83T-6312-B
57 mm
36 mm
7204E1
7204E
7204E2
303-239
303-240
T84T-6312-C
T84T-6312-D
57 mm
36 mm
7204E1
7204E
7204E2
303-239
303-240
T84T-6312-C
T84T-6312-D
57 mm
39 mm
7204E1
7823
303-239
308-454
T84T-6312-C
T93T-6312-B
54 mm
47 mm
7818
7817
7205E2
303-478
303-454
T94T-6312-AH
T83T-6312-B
57 mm
36 mm
7204E1
7204E
7204E2
303-239
303-240
T84T-6312-C
T84T-6312-D
57 mm
36 mm
7204E1
7204E
7204E2
303-239
303-240
T84T-6312-C
T84T-6312-D
82 mm
47 mm
7205E1
6068
303-213
303-591
T83T-6312-A
N/A
76 mm
36 mm
7887
7204E2
N/A
N/A
76 mm
36 mm
7887
7204E2
N/A
N/A
76 mm
36 mm
7887
7204E2
N/A
N/A
2-3/8"
1-7/16"
60 mm
36 mm
7855
7854
7204E2
N/A
N/A
2"
2-1/4"
51 mm
57 mm
7925-1
7925
7925-2
N/A
N/A
2-1/4"
1-7/16"
2-1/4"
1-7/16"
2-1/4"
1-7/16"
2-1/8"
1-7/8"
2-1/4"
1-7/16"
2-1/4"
1-7/16"
3-1/4"
1-7/8"
3"
1-7/16"
3"
1-7/16"
3"
1-7/16"
Adjustable Fan Clutch Holding Tool
• Adjustable jaws fit various water pump pulley bolt
4652
140
patterns.
• Jaws adjust from 1/2" to 8-5/16" opening.
• Jaws lock in place to securely hold water pump bolts.
• Long handle offers leverage for extra torque.
No. 4652 – Adjustable fan clutch holding tool.
Wt., 2 lbs., 5 oz.
AUTOMOTIVE SPECIAL TOOLS
Fan & Bearing Service
Ford Fan Clutch Wrench Set
• Set contains five of the most popular wrenches used
to service water pumps and fan clutches, and other
components on the front of Ford engines.
• Set contains three holding tools and two turning tools. Use with a 1/2" breaker bar or ratchet.
Note: Wrench Nos. 4585-2, 4585-3, and 4585-5 are used to
hold the water pump; wrench Nos. 4585-1 and 4585-4 are
used to turn the fan clutch.
1.Select the wrench that most closely fits the water pump,
and attach it to a 1/2" breaker bar or ratchet.
2.Select the wrench that most closely fits the O.D. of the
fan clutch nut.
3.Hold the water pump, and turn the fan clutch nut to
remove or install the fan clutch.
Note: Some Ford vehicles have left-hand threads on the fan
clutch. Refer to each vehicle service manual for the correct
thread specifications.
Replacement parts:
Part No.
Description
4585-1 – 48 mm (1-7/16") turning wrench.
4585-2 – 83 mm (3-1/4") holding wrench.
4585-3 – 72 mm (2-13/16") & 54 mm (2-1/8") holding wrench.
4585-4 – 40 mm (1-1/2") turning wrench.
4585-5 – 76 mm (3") & 68 mm (2-11/16") holding wrench.
No. 4585 – Ford fan clutch wrench set. Wt., 8 lbs., 6 oz.
Ford 6.0L Diesel Fan Clutch Wrench
Applications: 2003–newer Ford F-550 and F-650 Super
Duty trucks with the 6.0L diesel engine.
• This is a required tool to tighten or loosen the fan
clutch on the water pump.
• Wrench has a 68.45 mm (2-11/16") opening.
No. 6974 – Ford 6.0L diesel fan clutch wrench.
Wt., 3 lbs., 2 oz.
4585
Similar to
Ford 303-774
6974
141
AUTOMOTIVE SPECIAL TOOLS
Hub Service
Mercedes-Benz and BMW Fan Clutch Service Kit
• Mercedes-Benz fan clutch holding wrench holds the
Mirror
Finish
6985
water pump pulley to allow release of the fan.
• BMW Fan clutch holding wrench holds the water pump
pulley in place while loosening the radiator fan. Works
on BMW M10, M20, M30, & other late model vehicles.
(Holes at 38 mm & 44.5 mm.)
• Mercedes-Benz fan clutch wrench removes the thermoviscous radiator fans found on Mercedes-Benz and Ford
vehicles. Works on M-B engines: M111, OM604, OM605,
and OM606 (C & E Class; 36 mm opening).
Mercedes-Benz
fan clutch wrench is used to remove or install
•
the fan clutch assembly. Slim shaft handle lets you easily work
in tight spaces. Works on M-B engines: M103, M104, M119,
and M120 (65 mm opening).
• BMW fan clutch wrench is used to remove and install the
thermo-viscous fan on BMWs and Fords (32 mm opening).
• Mercedes-Benz Fan Clutch Holding Tool is used to remove /
replace thermo-viscous fan coupling with the radiator in place.
• Universal fan belt adjustment wrench services Mercedes-Benz,
Nissan Quest, and Mercury Villager radiator fans and pulley
belts. It also can be used for loosening the A/C idler pulley
tensioner lock nuts for A/C belt adjustment or replacement.
Also contains 2.5 mm, 8 mm, and 10 mm Allen keys.
No. 6985 – Mercedes-Benz and BMW fan clutch service kit.
Wt., 10 lbs., 2 oz.
HubTamer Elite Bearing Service Set
From start to finish, complete front wheel bearing service
using just one set of tools. Take off the hub, remove the old
bearing and install the new one, and then reinstall the hub.
All this is done while the knuckle assembly remains on the
car; no shop press or unnecessary alignments are needed.
• Works on virtually all floating and trapped rotors found on
domestic and import vehicles.
• Cuts service time 50% when replacing front wheel bearings.
• Pushes on the steering knuckle, not the rotor.
• Fits easily behind the rotor, leaving plenty of room for
positioning the tool and wrench. One-piece design has
no sliding arms to adjust and is impact wrench compatible.
The HubTamer Elite gives you these added benefits:
• Puller weldment adapter has been improved with the
addition of a beveled edge for use in tight fitting applications!
• Ford adapter for use on Taurus/Sable 1986–1995 and
Contour/Mystique 1995 – 2001 vehicles.
6537
6536
142
No. 6537 – HubTamer elite bearing service set. Includes all
adapters and tools necessary for removing hubs and replacing
front wheel bearings on most domestic and import vehicles
with floating or trapped rotors. Also includes updated case and
application information. Wt., 42 lbs., 13 oz.
If you want to update your current No. 6490 HubTamer, you
can purchase the weldment and Ford adapter separately.
No. 6573 – Weldment with beveled edge. Wt., 9 lbs.
No. 6536 – Ford adapter for Taurus/Sable and Contour/
Mystique. Wt., 1 lb., 3 oz.
AUTOMOTIVE SPECIAL TOOLS
Hub Service
Front Hub Installer and Puller Set
Here are three tools that make front hub service easier.
The universal puller removes front hubs from most FWD
cars without damaging wheel bearings. The installer is used
to pull the axle shaft into the front hub on Ford vehicles.
• Spare locknut works with a standard slide hammer puller
and the 7208A for rear axle flanges.
• Tools are available separately.
No 6298 – Front hub installer and puller set includes the
No. 7208A, 7135A, and 7924A in a molded plastic case.
Wt., 61 lbs., 8 oz.
No. 7208A – Hub remover to push the axle shaft from the
front hub. Wt., 2 lbs., 7 oz.
No. 7135A – Installer is used to pull the axle shaft into the
front hubs on Ford Taurus/Sable vehicles. Fits axle shafts
with 20 mm x 1.5 thread. Wt., 1 lb., 7 oz.
No 7924A – Installer is used to pull the axle shaft into the
front hub. Fits axle shafts with 22 mm x 1.5 thread on Ford
Contour/Mystique, Probe, and Focus. Wt., 1 lb., 5 oz.
7135A
7208A
7924A
Universal Hub Puller
With its adjustable sliding arms, this puller makes wheel-hub
removal quick, easy, and damage free. It has maximum bolt
circle of 7-1/2".
• The No. 32937 puller leg is available separately to complete
the five necessary for Cadillac and Jeep hub removal.
• Includes striking wrench and puller screw.
No. 7394 – Universal hub puller. Wt., 9 lbs., 2 oz.
No. 32937 – Puller leg. Wt., 1 lb.
7394
Front Hub Puller for 4WD Vehicles
• For removal of the front hub assembly, necessary for wheel
bearing or brake rotor service. Provides the mechanical
advantage and straight pull not possible with a slide
hammer.
• Will not work on trucks with dual rear wheels.
• Services:
-1988–2004 GM 1/2-ton, 3/4-ton, and 1-ton trucks, Tahoe,
Suburban, and Yukon.
-1994–2004 Dodge 1/2-ton, 3/4-ton, and 1-ton Ram trucks.
-1997–2004 Ford 1/2-ton trucks and Expeditions.
-1985–2001 Jeep Cherokee.
No. 6290 – Front hub puller for 4WD vehicles. Wt., 7 lbs. 2 oz.
Front Hub Puller for 4WD Vehicles
This puller is required for removing a front hub assembly in
3/4- and 1-ton 4WD pickups with 8-bolt hubs. It works on
1994 to 2004 Dodge Ram and 1988 to 2004 Ford and GM.
• Fits bolt hole pattern 8 x 6.5".
• Will not work on trucks with dual rear wheels.
• Use with our No. 7703 10-lb. slide hammer for maximum
pulling force.
No. 7901 – Front hub puller for 4WD vehicles. Wt., 5 lbs.
6290
7901
143
AUTOMOTIVE SPECIAL TOOLS
Hub & CV Joint Service
7932
Similar to
Ford 202-405
Similar to
Ford 205-404
Ford Vacuum Front Hub Release Tool Set
Here’s the equipment you need to safely remove the plastic
vacuum hubs on Ford pickups. Standard tools won’t work
for the job, but this set has special clips that slip into slots
on the hub to release it.
• For use on 1998 to 2000 4WD Ranger with vacuum front
hubs.
No. 7932 – Ford vacuum front hub release tool set.
Wt., 10 oz.
No. 7932-1 – Ford vacuum front hub puller. Wt., 8 oz.
No. 7932-2 – Ford vacuum front hub removal clip set.
Wt., 3 oz.
Ford Axle Shaft Seal Installer
6695
Similar to
Ford 303-429
• Works on 1998-newer Ford F-250, F-350, F-450, and
F-550 4X4s having the vacuum-operated front axle.
• Correctly installs the seal onto the axle shaft and into the wheel knuckle, preventing front hub vacuum leaks that would cause the 4WD to not engage.
No. 6695 – Ford axle shaft seal installer. Wt., 10 lbs., 8 oz.
Hub Resurfacing Kit
• Fits your power drill to quickly sand rust off lug studs and
rotors on the hub assembly. Sanding pads attach with
Velcro™.
• For most domestic and import vehicles with either front or
rear disc brakes. Includes holder and five sanding discs.
• Run at speeds of 1200 rpm or less for best results.
(Do not exceed 1200 rpm.)
No. 7942A – Hub resurfacing kit. Wt., 5 oz.
No. 222548 – 10 pack of replacement sanding pads
for No. 7942A. Wt.,1 oz.
No. J-42450-9 – Replacement holder for No. 7942A.
Wt., 4 oz.
7942A
Similar to
Ford 204-D020
(D93T-3206-A)
7502
144
4WD Front Spindle Puller
This puller enables you to remove the front spindle on
light-duty 4WD trucks. It’s designed for full-size Ford, GM,
International, and Jeep pickups with Dana front axles. Also
works on Ford Ranger and Bronco II.
• 5/8" fine thread makes it ideal for use with our No. 1155
slide hammer.
• Fits spindle thread sizes 2"-16, 1-5/8"-16 and 38 mm-1.5.
No. 7502 – 4WD front spindle puller. Wt., 2 lbs., 8 oz.
AUTOMOTIVE SPECIAL TOOLS
CV Joint Service
Subaru Front Axle Shaft Installer
Here’s a real time saver when servicing front axles, CV
joints, or wheel bearings on 1980 to current Subaru.
• Fits 24 mm x 1.5 axle shafts.
No. 7535 – Subaru front axle shaft installer.
Wt., 2 lbs., 8 oz.
7535
Bearing Cup Remover
This is an ideal tool for servicing hubs on today’s small
FWD cars. It’s perfect for pulling internal bearing cups,
seals, and bushings.
• Jaws spread 15/16" to 3-1/4" and reach to 3-1/2".
• Use with any slide hammer having 5/8"–18 thread
(our Nos. 1155 or 1156, or the 927 Push-Puller).
No. 6542 – Universal bearing cup remover. Wt., 1 lb., 8 oz.
Outer Tie Rod Remover/ Ball Joint Separator
This tool is a must when you’re servicing outer tie rods.
It works on imported and domestic models, front- or rearwheel drive, cast or stamped-steel steering knuckles.
• Handles up to 5 tons of knuckle twisting force.
• Jaw reach is 3" with a spread of 3".
• Jaws, once tightened, won’t slip on the knuckle.
• Can be used to separate lower ball joints on import
FWD vehicles.
No. 7503 – Outer tie rod remover. Wt., 2 lbs., 12 oz.
6542
Similar to Kent-Moore
No. J-24319-B
7503
Inner CV Joint Puller
This is the puller you need for CV work on many Ford cars.
Used with a slide hammer, it will remove an axle assembly
from the transaxle without causing damage to expensive
aluminum transmission cases or other components.
No. 7507 – CV joint fork only. Use with
OTC slide hammer No. 1155, extension
No. 7508, or both. Wt., 13 oz.
No. 7508 – 17-1/2"-long slide hammer
extension. Wt., 2 lbs., 7 oz.
No. 7509 – Complete CV joint tool.
Wt., 8 lbs.
U-Joint Removing/ Installing Tool
This helpful tool uses a forcing-screw press to safely
remove and replace automotive universal joints with needle
bearings, including GM plastic pin CV U-joints.
No. 7248 – U-joint removing/installing tool. Wt., 9 lbs., 7 oz.
Similar to Ford
No. 205-086
(T74P-4635-C)
7509
7507
7508
5/8" x 18 thread
7248
145
AUTOMOTIVE SPECIAL TOOLS
CV Joint Service
7995
Outer CV Joint Remover
Removes the outer CV joint on most front-wheel drive
vehicles with a concealed internal circlip.
• Use with OTC No. 1155 or 1156 slide hammer with 5/8-18
UNF thread.
No. 7995 – Outer CV joint remover. Wt., 2 lbs., 6 oz.
Outer CV Joint Remover
• Use to remove the outer CV joint on most front-wheel
4703
drive vehicles with a concealed internal circlip.
• Use with slide hammer that has 5/8-18 UNF thread.
• Do NOT use this tool to remove front axle assemblies.
The inner or outer CV joint may be pulled apart inside
the axle boot.
No 4703 – Outer CV joint remover. Wt., 1 lbs. 10 oz.
Boot Clamp Pliers – Chrysler
• Required tool for correct installation of strap-and-buckle
style CV boot clamps.
on A.C.I. and G.K.N. boots found on various
•
Chrysler, Plymouth, and Dodge front-wheel drive vehicles.
• Prevents damage to CV boot and clamp during
installation.
No 4720 – Boot clamp pliers – Chrysler. Wt., 7 oz.
Works
4720
Dust Boot Cap Installer
Works on all vehicles with band-type boot clamps (up to
1/4" wide & .020" thick). The clamp must be installed
correctly after servicing to prevent moisture and foreign
material from entering the CV joint area. This tool
provides exact installation of those clamps with ease.
No. 7085 – Boot clamp installer. Wt., 8 oz.
7085
4724
CV Boot Clamp Pliers
• Special tips work on the ear-less type CV boot clamps.
• Grips clamp in many positions to tighten clamp around
boot.
No. 4724 – CV boot clamp pliers. Wt., 12 oz.
146
AUTOMOTIVE SPECIAL TOOLS
CV Joint Service
Ear-type CV Boot Clamp Pliers
• For removal of the front hub assembly, necessary for
wheel bearing or brake rotor service. Provides the
mechanical advantage and straight pull not possible with
a slide hammer.
• Services:
-1988–2000 GM 1/2-ton, 3/4-ton, and 1-ton trucks, Tahoe,
Suburban, and Yukon.
-1994–2000 Dodge 1/2-ton, 3/4-ton, and 1-ton Ram trucks.
-1997–2000 Ford 1/2-ton trucks and Expeditions.
-1985–2001 Jeep Cherokee.
No. 4723 – Ear-type CV boot clamp pliers. Wt., 13 oz.
4723
Heavy-Duty CV Boot Clamp Installer
• Designed to clamp the ear-type CV boot clamps used on
front-wheel drive vehicles.
• May also be used to crimp the clamps used on fuel and
cooling system hoses.
• Ensures even, precise crimping, and eliminates possibility
of damage to the clamp, boot, or hose.
No. 4722 – Heavy-duty CV boot clamp installer.
Wt., 1 lb., 7 oz.
4722
CV Boot Clamp Cutter
• Designed to easily cut the CV boot clamp without
damaging the boot.
cut boot clamps up to 10 mm wide and .7 mm thick.
•
Handles
are spring loaded to the open position to allow
•
easy access to the clamp.
No. 4721 – CV boot clamp cutter.
Wt., 12 oz.
Will
4721
CV Joint Banding Tool and Cutter
• Use to install and tighten the “band-it” or strap style
clamps on CV joint boots, or on power steering rack and
pinion steering gear boots.
• Once installed into the tool, tighten the band by turning the
handle on the tool; use a socket or wrench on the handle
to torque the band to OE specifications.
• When the boot clamp has been tightened to specs, cut the
band to the correct length by flipping the lever (at the front
of the tool) forward.
No. 4623 – CV joint banding tool and cutter. Wt., 10 oz.
4623
147
AUTOMOTIVE SPECIAL TOOLS
Rear Axle Service
7792
7372
7374
Rear Axle Service Set
The tools you need for flange-type rear axle and
bearing removal on most late model passenger cars and
light trucks. Set includes the No. 7374 rear axle pulling
plate and 5 lb. slide hammer. The axle bearing pullers,
used with the slide hammer, make short work of removing
semi-floating rear axle bearings.
No. 7792 – Rear axle service set. Wt., 11 lbs., 4 oz.
Consists of:
No. 7374 - Rear axle pulling plate with 5 lb. slide hammer.
No. 7495A - Rear axle bearing puller. Fits min. bearing tube
I.D. of 1" and max. axle tube I.D. of 1-7/8".
No. 7496A - Rear axle bearing puller. Fits min. bearing
tube I.D. of 15/16" and max. axle tube I.D. of 2-3/8".
No. 7497A - Rear axle bearing puller. Fits min. bearing
tube I.D. of 1-3/8" and max. axle tube I.D. of 2-7/8".
No. 27315 - Puller hook for use with the 5 lb. slide
hammer. Removes oil seals, bearings, etc.
Slide Hammer Rear Axle Puller
This puller will enable you to remove flange-type rear axles
from most late model cars and light trucks. It works on axles
having bolts and studs up to 9/16" diameter.
• Fits 4-, 5-, or 6-bolt patterns and stud circles from 4-1/4"
to 5-9/16".
No. 7372 – Rear axle pulling plate. Wt., 1 lb., 7 oz.
No. 7374 – Rear axle pulling plate with 5-lb. slide hammer
assembly. Wt., 8 lbs., 13 oz.
Pulling Hook
6541
148
• This slide hammer puller attachment is used to remove
seals, bearings, and other press-fit parts.
• Designed to be used with OTC No. 1155 (5 lb.) or
No. 1156 (2-1/2 lb.) slide hammer, or other slide hammers
having 5/8-18 threads.
No. 6541 – Pulling hook. Wt., 8 oz.
AUTOMOTIVE SPECIAL TOOLS
Rear Axle Service
Rear Axle Bearing Puller Set
• Set contains slide hammer and popular attachments
needed for servicing flange-type, floating rear axle
bearings and seals in most late model, rear-wheel drive
cars and light trucks; comes in a molded case.
• Rear axle bearing puller fits min. bearing tube I.D. of 1"
and max. axle tube I.D. of 1-7/8".
• Rear axle bearing puller, fits min. bearing tube I.D. of
1-5/16" and max. axle tube I.D. of 2-3/8".
• Rear axle bearing puller fits min. tube I.D. of 1-3/8" and
max. axle tube I.D. of 2-7/8".
Also includes: Slide hammer tee bar, slide hammer 5 lb. weight, pulling
hook, rear axle pulling plate, bearing cup remover
No. 6540 – Rear axle bearing puller set. Wt., 11 lbs., 7 oz.
6540
Rear Axle Bearing Service Set
All three pullers have been redesigned to make the removal
of semi-floating rear axle bearings easier. The new design
allows you to capture the bearing firmly, distributing the
pulling force over the entire bearing. This reduces damage
and increases the amount of applications. Set includes three
pullers to service most domestic cars. Use with OTC Nos.
1155 or 1156 slide hammer with 5/8"-18 UNF thread. Pullers
also available separately.
No. 7494A – Rear axle bearing puller set. Includes one
each Nos. 7495A, 7496A, and 7497A, and a storage case.
Wt., 2 lbs., 8 oz.
No. 7495A – Rear axle bearing puller. Fits minimum bearing
tube I.D. of 1" and maximum axle tube I.D. of 1-7/8".
Wt., 12 oz.
No. 7496A – Rear axle bearing puller. Fits minimum bearing
tube I.D. of 1-5/16" and maximum axle tube I.D. of 2-3/8"
including 1988–1997 Chevrolet and GMC 8-1/2", 1/2-ton
rear axle bearing. Wt.,12 oz.
No. 7497A – Rear axle bearing puller. Fits minimum bearing
tube I.D. of 1-3/8" and a maximum axle tube I.D. of 2-7/8".
Wt., 12 oz.
7494A
When does your clock start?
Robinair’s new transmission oil exchanger
has the vehicle in and out of the service
bay in less than 20 minutes!
Our unique approach to exchanging fluid...
through the transmission oil dipstick!
• Exchange oil in the pan before it passes through the
transmission filter.
• Easy, convenient, and no damage to other engine components.
• It cannot be hooked up backwards.
• No rusty fittings to break loose.
149
AUTOMOTIVE SPECIAL TOOLS
Transmission Fluid Exchanger
Transmission Fluid Exchanger
• Top-off feature. Add or subtract in 1/10 qt. increments.
• “Low Fluid Alarm” and “Indicator Light” to alert operator.
• “Drain Waste” feature automatically pumps used fluid from the
machine into a waste oil container.
• “Drain Pan” feature drains the pan for easy filter
replacement. No mess.
Three modes of operations: Dipstick only, cooler
line, or a combination of the two!
Specifications
Electrical
Exchange Accuracy
Controls
Fluid Tanks
Hoses
Fluid Types
Adapter Set
Pump
Weight
Dimensions
Process Time
Warranty
92500
12V DC
+/ - 1/4 qt.
Microprocessor with digital
keypad and LEDs
32 quarts (24.6 liters) each for
both new and used fluids
91" black and red (Exchange);
76" white transfer tube (Straw)
Multiple fluid capability.
Complete set for most applications. Standard adapters for Ford, GM, Chrysler, European,
and Universal (covering most
Asian imports).
Positive displacement gear
pump, 2 gallons per minute
maximum
158 lbs. (72 kg)
52"H x 33"W x 20"D (132 cm x
84 cm x 51 cm)
Depends on mode
1 year parts and labor
• Exchange accuracy approximately +/ - 1/4 qt.
• 32-quart supply tank; 34-quart waste tank.
• Unprecedented one-tenth quart flow metering for adding or
subtracting fluid from the pan.
• Complete set of cooler line
adapters for most foreign and domestic vehicles.
• Works with all types of automatic transmission fluid.
• Integral performance designed hose and tool compartment with drain.
No. 92500 – Transmission fluid
exchanger. Wt., 215 lbs.
No. 529734 – Replacement nylon
tube.
Automatic Transmission Fluid Diagnostic Pads
92001
Easy, quick way to test automatic transmission fluid to determine when
service is necessary. Simply place a few drops of transmission fluid
from transmission dipstick onto test pad. Pad will change color
indicating condition of transmission fluid. Package contains 100 pads.
No. 92001 – Automatic transmission fluid diagnostic pads. Wt., 4 oz.
Transflow Transmission Oil Cooler Flusher
Fix it right the first time... designed to measure oil flow capacity
within the transmission oil cooler, and also has the capability to
flush contaminated oil from the TOC after repairs.
• Only unit in the industry that performs a flow rate test.
• Flush and flow test time is 5 to 8 minutes.
• 32-quart supply tank; 34-quart waste tank.
• Supply and waste hoses each 10' long.
• 10' long, 12V DC power cables with battery lead clips.
• Requires shop air (90 psi, min.) and 12V DC source.
No. 92000 – Transflow transmission oil cooler flusher.
Wt., 173 lbs.
150
92000
AUTOMOTIVE SPECIAL TOOLS
Torque Converter Service
Portable Torque Converter and
Oil Cooler Cleaner
When a newly overhauled transmission fails, it’s
goodbye to profits and customer goodwill! Often a dirty
torque converter or oil cooler is the culprit—sludge and
metal particles can jam up valve bodies and clog filter
screens, causing malfunctions and costly comebacks.
Developed with the cooperation and approval of leading auto manufacturers, this cleaner effectively removes
contaminants from converters and also performs the
essential job of flushing out transmission oil cooler and
cooler lines on most popular makes, 1960–current. A
pair of hoses for attachment to the cooler lines is
provided. The vehicle’s converter is bolted to a
universal mounting plate, and the adjustable timer is
set for desired cycle period. As the converter is rotated
at 20 rpm, cleaning solvent is circulated through it and
intermittent injections of compressed air into the solvent
provide an effective pulsating, cleaning action.
No. 60081 – Torque converter/cleaner, complete with
­cooler flushing hoses, one 200251 adapter, two 10017
cap screws for ­C-3 ­transmissions, and three 15677
metric cap screws. Instruction manual. Wt., 230 lbs.
LR19814
LR 19814
Specifications
60081
Pump
Fixed displacement-type. Delivers a
maximum of 6-1/2 gallons per minute.
Import Car
Hose and
Timer
Converter
Switch
*Pump Motor 1/3 hp, 110 volt AC single-phase. Quick Coupler Converter
Fused for thermal protection.
*Gear Motor
1/15 hp, 110V AC single-phase, d.p.s.p., 20 r.p.m.
Reservoir
Five-gallon capacity. Equipped with
easily accessible drain cock.
Filter
Replaceable, full-flow, 5-micron diesel Control
Standpipe and
Universal
Clamp Adapter and
Special Adapter
fuel filter.
Switch
Splashguard Assy. Mounting
Adjusting Bracket
for Clamp
Plate
Extension
Timer
30-minute maximum cycle mechanical timer. Can be set in 1 minute
Item Part No. Description
Req’d.
increments if desired.
1
A
200251 Spacer adapter
Cabinet
41" high x 28" wide x 19-1/2" deep. B
200231 End cap
1
Welded steel construction. Has
C
15677
Cap screw
3
free-wheeling casters.
D
10017
Cap screw
2
*Note: Products are available in other voltages. Contact
your customer service representative for the part
numbers to order.
Accessories
For added versatility, you may order the accessories
listed to the left, which adapt the 60081 unit for
cleaning a variety of foreign and small domestic
automatic transmission converters.
C
A
B
D
151
AUTOMOTIVE SPECIAL TOOLS
Transmission Service
Transmission Fluid Fill Adapter
6604
Similar to
Ford No. 307-437
• This is a required tool to fill or add fluid to the 5R55W
automatic transmission used on 2003–newer Ford
Explorers.
• Operating Instructions: Remove fill plug from transmission; install No. 6604; fill transmission to correct fluid level;
remove No. 6604; and reinstall fill plug in transmission.
No. 6604 – Transmission fluid fill adapter. Wt., 1 oz.
Transmission Adapter Kit
7118
Replaces OTC
tool No. 7646
7646A
No. 7244 – Similar to
Ford No. 307-123
(T82L-9500-AH) and
Kent-Moore No. J-36391
No. 7587 – Similar to
Ford No. 307-176
(T86P-77265-AH)
152
Converts your OTC No. 1726 or No. 1735 engine stand into
a transmission service stand. Kit replaces the adjustment
arms of the stand to hold and position the transmission at
workbench height for repair.
• The transmission is held with three sides fully exposed for
working convenience.
• Can be rotated a full 360° for complete access to all parts.
• Comes with mounting hardware.
No. 7118 – Transmission adapter kit. Wt., 10 lbs., 8 oz.
Ford Clutch Coupling Tool
• Disconnects the hydraulic clutch line from the clutch slave
cylinder on the following vehicles with manual transmissions
and hydraulic clutches: 1988–2006 F-series trucks, Bronco
II, Ranger, Explorer, and 1989–1997 Ford Thunderbird and
Mercury Cougar.
• Wedge-shaped design allows easy removal of clutch line
without damaging clutch line, coupling, or slave cylinder. No
need to pry the coupler apart.
No. 7646A – Ford clutch coupling tool. Wt., 4 oz.
Quick-Disconnect Tool
Two popular disconnect tools in one set give you the
versatility to quickly separate the quick connectors found
on everything from radiators to transmission and power
steering lines. The quick-disconnect coupler tool, No. 7244,
works on late model Ford and GM vehicles without
disturbing the quick-connect seals. No. 7587 releases the
finger on the transmission-to-radiator oil cooler line quickly,
without damaging the hose or connector. Works on 1986
and newer Ford Tauruses and Mercury Sables with an
AXOD, AOD, or ATX transmission.
• Tools available separately.
No. 7244 – Quick-disconnect coupler tool. Wt., 2 oz.
No. 7587 – Ford oil cooler line disconnect tool. Wt., 5 oz.
AUTOMOTIVE SPECIAL TOOLS
Transmission Service
GM Hydraulic Clutch Line Disconnect Tool
This is a versatile tool for disconnecting clutch lines when
you’re working on clutch assemblies or slave and master
cylinders. The bent end, intended for NVG3500 and NV4500
manual transmissions, works on 1996 to 2004 full-size 2WD
and 4WD trucks, Chevrolet S-10 Blazer, and pickups. The
straight end is for 1993 to ‘94 Chevrolet Lumina sedan,
1995 to 2000 Chevrolet Monte Carlo, 1993 to ‘99 Buick
Regal, 1998 to 2002 Olds Intrique, 1993 to ‘97 Olds Cutlass
Supreme and Pontiac Grand Prix.
No. 7910 – GM hydraulic clutch line disconnect tool.
Wt., 5 oz.
Automatic Transmission Clutch Spring
Compressor
7910
Similar to Kent-Moore
J-42371, J-36221
Similar to Ford
No. T65L-77515-A
This is a handy, adjustable tool for removing or installing
the snap ring on a transmission rear clutch piston. It applies
pressure to the clutch drum’s retaining washer to compress
piston return springs.
• For use on most American cars and light trucks.
No. 7024 – Automatic transmission clutch spring
compressor. Wt., 2 lbs., 13 oz.
7024
Transmission Disconnect Set
This set is used to service automatic transmission cooler
lines and manual transmission hydraulic clutch lines.
Set includes:
No. 7937 – GM transmission oil cooler line disconnect tool.
No. 7646A – Ford clutch coupling tool.
No. 7910 – GM hydraulic clutch line disconnect tool.
No. 7244 – GM & Ford oil cooler line disconnect tool.
No. 7798 – Ford oil cooler line disconnect tool.
No. 519378 – Chrysler/Jeep oil cooler line disconnect tool.
No. 6520 – Transmission disconnect set. Wt., 1 lbs., 15 oz.
6520
Ford Transmission Cooler Line
Disconnect Set
1/2" is similar to
Ford No. 307-459.
• Snap around cooler line, push into the fitting, fitting
releases. The cooler line can then be removed.
disconnect is used on 2003–newer Ford Explorers with
•
the 5R55W transmission.
• 1/2" disconnect is used on 2003–newer Ford Super Duty
trucks with the 4R100 transmission.
No. 6593 – Ford transmission cooler line disconnect set.
Wt., 8 oz.
3/8" is similar to
Ford No. 307-441.
3/8"
6593
Transmission Line Disconnects
•Used on 2001 to current Chevrolet Corvette with the 4L60E transmission, and 2003 to current Cadillac CTS with the 5L40E transmission.
• 6 per pack.
No. 6611 – Transmission line disconnects. Wt., 4 oz.
6611
153
AUTOMOTIVE SPECIAL TOOLS
Transmission Service
Dodge Transmission Cooler Line
Disconnect Tool
Similar to
Miller No. 8218
6047
7937
• Designed for removing the cooler line from the radiator
to transmission on 1995 and newer Dodge pickups with
automatic transmissions.
• Tool encloses the quick connect fittings and releases the
locking fingers on the line. It works on both 3/8" and 1/2"
lines.
No. 6047 – Dodge transmission cooler line disconnect tool.
Wt., 4 oz.
GM Transmission Oil Cooler Line
Disconnect Tool
• Specially designed to work in tight places. So simple to
operate, you can do it with just one hand.
insertion into the quick-connect fitting on 1/2" dia.
•
lines, a quarter turn of the tool quickly and easily releases
the fitting on the transmission end of the transmission-toradiator oil cooler line.
• Works on 2WD and 4WD pickups and vans with
electronic shift overdrive automatic transmissions: 1991–
newer 4L80E transmissions, and 1993–newer 4L60E
transmissions.
No. 7937 – GM transmission oil cooler line disconnect tool.
Wt., 2 oz.
After
Clutch Alignment Tool Set (17 piece)
• Essential for clutch installation on virtually all cars and
4528
154
light-duty trucks. Aligns clutch plate by using tapered
cones and pilot adapters.
• Includes seven fractional pilot adapters, 1", 13/16",
25/32", 3/4", 11/16", 5/8", 19/32" one clutch disc
centering adapter, and one alignment shaft.
• Includes five metric pilot adapters, 19mm, 17mm,
16mm, 14mm, 12mm, two clutch disc centering adapters,
and one alignment shaft.
• Housed in a blow-molded storage case.
No. 4528 – Clutch alignment tool set (17 piece).
Wt., 4 lbs., 3 oz.
AUTOMOTIVE SPECIAL TOOLS
Differential Service
Differential Bearing Pullers
For removing differential side carrier bearings on a wide
variety of passenger cars and light trucks. Use with step
plate adapters Nos. 8060, 8061, 8063, and 8064. (Step
plate adapters are not included with 1028 or 1031.)
No. 1028 – Puller with 3-1/2" maximum reach, 1-1/4" to
4-1/2" spread. Primarily for servicing Ford products.
Wt., 1 lb., 13 oz.
No. 1031 – Puller with 3-1/4" maximum reach, 6"
maximum spread. For servicing most General Motors,
American Motors, and Chrysler products. Wt., 2 lbs.
1028
1031
Escort/Lynx Half-Shaft Remover/
Differential Rotator
This tool is required when you’re removing the left-hand
half-shaft from Escort/Lynx transaxles. It ensures removal
and enables you to turn the differential.
No. 7140 – Escort/Lynx half-shaft remover/differential
rotator. Wt., 1 lb., 13 oz.
7140
Differential Bearing Preload Wrench
• Similar to Miller C-4164.
• Use to adjust differential bearing free play on Chrysler/
Dodge vehicles with 7-1/4", 8-1/4", 8-3/4", and 9-1/4" rear
axles.
• Tool fits inside axle tube to access the threaded adjusters.
No. 6602 – Differential bearing preload wrench.
Wt., 2 lbs., 14 oz.
Similar to
Miller C-4164
6602
Differential Housing Spreader
Here’s a tool that eases the job of removing or installing
differential ring-gear assemblies on Dana axle models
30 through 70. It’s a heavy-duty device using mechanical screw power to spread the housing. It helps prevent
the component damage that often results from the use of
homemade devices.
No. 7071 – Differential housing spreader. Wt., 34 lbs.
7071
Toyota A/C Disconnect Tool
• Used to release the plastic quick-connect fittings on
the high- and low-pressure air conditioning lines at the
evaporator.
• Services 1998–newer Toyota Corolla, 1998–newer Geo
Prizm, 1998-1/2–newer Toyota Land Cruiser and Lexus
LX470, 1999–newer Toyota Avalon, Camry, Solara, and
Sienna mini vans.
• Easy to use: Plastic fitting on A/C line is rotated to
show access to the two release holes in the fitting; tool
is inserted into release holes, and pushed to release the
fitting.
No. 6073 – Toyota A/C disconnect tool. Wt., 4 oz.
6073
155
AUTOMOTIVE SPECIAL TOOLS
Fuel & A/C Service
518898 – Similar to
Ford No. 412-027
(T81P-19623-G2)
518897 – Similar to
Ford No. 412-038
(T83P-19623-C)
A/C Spring-Lock Coupling Tool Set
These tools will quickly separate spring-lock refrigerant
pressure lines on the air conditioning systems of 1981 to
2002 Ford vehicles, and 1994 to 2002 Chrysler and Jeep
vehicles.
• Spring-loaded in the closed position to deflect spray
that occurs when a line is disconnected.
• Tools available separately.
No. 6538 – Set of four A/C spring-lock coupling tools:
Wt., 3 oz.
518900 – Similar to No. 518901 – 3/4" (white). Wt., 2 oz.
518901 – Similar to
Ford No. 412-026
Ford No. 412-040
No. 518900 – 3/8" (red). Wt., 2 oz.
(T81P-19623-G1)
(T85L-19623-A)
No. 518898 – 1/2" (blue). Wt., 2 oz.
No. 518897 – 5/8" (black). Wt., 2 oz.
6538 – Similar to Ford No.
412-039 (T84L-19623-B)
A/C and Fuel Line Disconnect Set
• Used to remove A/C and fuel line quick-disconnect
4495
fittings from hard-to-reach areas.
• sizes (5/16", 3/8", 1/2", 5/8", 3/4", and 7/8") available
to work on many import and domestic vehicles.
No. 4495 – A/C and fuel line disconnect set.
Wt., 5 oz.
Six
Fuel and Air Conditioning Line
Release Tool
• This spring-lock coupling release tool easily separates
4494
156
fittings on fuel and air conditioning lines.
sizes are 3/4", 5/8", 1/2", and 3/8".
•
No. 4494 – Fuel and air conditioning line release tool.
Wt., 5 oz.
Tool
AUTOMOTIVE SPECIAL TOOLS
Fuel & A/C Service
Full-Coverage Disconnect Tool Set
If you’re working on Chrysler, Ford, or General Motors vehicles,
this set will make your job easier. The tools are designed for
heater hoses, transmission oil coolers, air conditioning and
fuel lines. They’re approved by vehicle manufacturers and will
not damage the fittings being disconnected. Tool Nos. 518092,
518896, 518897, 518898, 518899, 518900, and 518901 are
spring-loaded in the closed position to deflect any spray that
occurs when lines are disconnected.
• Comes in blow-molded case.
No. 6508 – Disconnect tool set. Wt., 4 lbs., 8 oz.
6508
Contents of set:
Tool
Description
Tool
Description
440384
GM hydraulic clutch line
disconnect tool.
518901
A/C spring lock coupling tool.
(White, 3/4" )
440486
GM transmission oil
cooler line.
519067
Fuel line disconnect tool.
511410
Fuel line disconnect tool.
519068
Fuel line disconnect tool.
511413
Fuel line disconnect tool.
519151
Quick disconnect tool.
518902
Heater hose disconnect tool.
519158
Fuel line disconnect tool set.
519152
Oil cooler line disconnect tool.
519153
Clutch coupling tool
518582
Fuel line disconnect tool.
519154
Fuel line coupling tool.
519155
Chrysler fuel line disconnect tool.
519156
Ford heater hose disconnect tool.
519157
GM heater line quick connect separator.
519159
Oil cooler line disconnect tool.
518583
Fuel line disconnect tool.
518584
Fuel line disconnect tool.
518896
Fuel line disconnect tool.
(Yellow, 3/8" )
518897
A/C spring lock coupling tool.
(Black, 5/8" )
518898
A/C spring lock coupling tool.
(Blue, 1/2" )
518899
Fuel line disconnect tool.
(Green, 1/2" )
518900
A/C spring lock coupling tool.
(Red, 3/8" )
157
AUTOMOTIVE SPECIAL TOOLS
Locknut Sockets
Locknut Sockets
No. 7090A – Services 1978–84 Ford F-series H.D. 3/4-and
1-ton 4WD trucks; 1973–81 GM 3/4- and 1-ton 4WD trucks.
1/2" sq. drive. Wt., 1 lb., 11 oz.
7090A
2-5/8"
Similar to Ford
No. 205-D001
(D78T-1197-A)
7157
2-1/4"
Similar to Ford
No. 205-192
(T83T-1197-B)
No. 7158 – Services 1985-1/2–95 Ford F-series H.D. 3/4and 1-ton Dana 50 IFS of Dana 60 front axle; 1982–90 GM
H.D. 3/4- and 1-ton trucks, 1994–newer Dodge Dana 60 with
Cummins. 1/2" sq. drive. Wt., 1 lb., 13 oz.
No. 7795 – Services 1995–1996 Ford F-series 1/2-ton trucks
and full-size Bronco with automatic hubs. 1/2" sq. drive.
Wt., 1 lb., 11 oz.
7158
2-1/2"
Similar to Ford
No. 205-D065 (D85T-1197-A)
No. 7796 – Services 1995–1998 Ford F-series 3/4- and 1-ton
trucks with automatic hubs. 1/2" sq. drive. Wt., 2 lbs., 2 oz.
7795
2-1/2"
Similar to Ford
No. 205-348
(T95T-1197-A)
7796
2-3/4"
No. 7270A – Services 1984–92 Ford Ranger and Bronco II
with manual hubs; 1986–95 Ford F-series 1/2-ton truck; fullsize Bronco with Dana 44 front axle; 1990–93 Dodge trucks
with Dana 44 automatic hubs. 1/2" sq. drive. Wt., 1 lb., 8 oz.
No. 7269 – Services 1985–newer Ford F-series 3/4- and
1-ton trucks with Dana 80 rear axle. 1/2" sq. drive. Wt., 3 lbs.
No. 7698 – Services 1988–1995 Isuzu Trooper, Rodeo,
Amigo, and pickup; 1989–1995 Honda Passport; Jeep J20
pickups with Dana 60 axle. 1/2" sq. drive. Wt., 1 lb., 5 oz.
Similar to Ford
No. 205-349
(T95T-1197-B)
No. 7913 – Used to remove and install locknut on 1997–2000
Suzuki Samurai and Geo Tracker front hubs. Wt., 2 lbs., 2 oz.
7270A
2-3/8"
Similar to Ford
No. 205-244
(T86T-1197-AR)
7269
2-3/4"
No. 7612 – 54 mm hex socket fits front wheel bearing adjusting nut of Toyota FJ, LN, and RN. Has 1/2" square drive end,
permitting use of a torque wrench. 1/2" sq. drive.
Wt., 1 lb., 15 oz.
No. 7941 – Specially designed to fit 4WD lock-out hubs on
Toyota’s 1995–2002 Tacoma, and 1996–2002 T100 and
4Runner. Similar to Toyota No. 09318-12010-01. Wt., 8 oz.
No. 6006 – Services 1994–newer Dodge 1/2-ton 4x4 pickups
with Dana 44 front axle and Dana 60 axle with vacuum
disconnect front axle. Wt., 1 lb., 10 oz.
Similar to Ford
No. 205-282
(T88T-4252-A)
Kent Moore
No. J-42855
No. 1902 – Services 1984–92 Ford Ranger and Bronco II
with automatic hubs; 1993–1997 Ford Ranger, Bronco II, and
Explorer with automatic hubs. 1/2" sq. drive. Wt., 1 lb., 14 oz.
7698
2-1/4"
6601
Similar to Ford
No. 205-448
158
No. 7157 – Services 1993–newer Ford Ranger Bronco II and
Explorer with manual hubs; 1995–96 Ford F-series 1/2-ton
truck and full-size Bronco with manual hubs; 1995–newer
Ford F-series 3/4-ton and 1-ton trucks with manual hubs;
1959–85 Ford F-series 1/2- and 3/4-ton trucks and full-size
Bronco; 1960–90 GM 1/2-ton truck and full-size Blazer/Jimmy;
1969–89 Dodge 1/2-ton truck with manual hubs; 1969–72
International 1/2-ton truck. 1/2" sq. drive. Wt., 1 lb., 8 oz.
No. 1928 – Services 1990–93 Dodge truck with Dana 60
manual hubs. 3/4" sq. drive. Wt., 2 lbs., 2 oz.
No. 1936 – Services 1990–newer Ford Ranger, Bronco II, and
Explorer with automatic hubs. Wt., 1 lb., 15 oz.
No. 6601 – Services 2003–newer Ford F-250, F-350, and
F-450 Super Duty trucks with 10-1/2 inch rear axle.
Wt., 2 lb., 15 oz.
AUTOMOTIVE SPECIAL TOOLS
Locknut Sockets
FW Bearing Locknut Sockets Application Chart
Vehicle
OTC No.
Ford No.
1984–92 Ford Ranger & Bronco II with manual hubs
7270A T86T-1197-AR
with automatic hubs
1902 T70T-4252-B
1993–95 Ford Ranger,
Bronco II, and Explorer
with manual hubs
with automatic hubs
1990–95 Ford Ranger,
Bronco II, and Explorer
with automatic hubs
7157 T83T-1197-B
1902 T70T-4252-B
1936
N/A
Global No.
205-244
205-039
205-192
205-039
N/A
1995–96 Ford F-series
1/2-ton trucks and full-size Bronco
with manual hubs
7157 T83T-1197-B
with automatic hubs
7795 T95T-1197-A
205-192
205-348
7157 T83T-1197-B
7796 T95T-1197-B
205-192
205-349
1995–98 Ford F-series 3/4- and
1-ton trucks with manual hubs
with automatic hubs
1978–84 Ford F-series
H.D. 3/4- and 1-ton 4WD trucks 7090A D78T-1197-A
19851/2–95 Ford F-series
H.D. 3/4- and 1-ton Dana 50 IFS
or Dana 60 front axle 7158 D85T-1197-A
1985–95 Ford F-series
1/2-ton truck and full-size Bronco
with Dana 28 front axle
1959–85 Ford F-series 1/2- and
3/4-ton truck and full-size Bronco
1986–95 Ford F-series
1/2-ton truck and full-size Bronco
with Dana 44 front axle
1973–81 GM 3/4- and
1-ton 4WD trucks 1960–90 GM 1/2-ton truck
and full-size Blazer/Jimmy
1982–90 GM H.D. 3/4- and
1-ton trucks 1989–96 Tracker 1969–72 International
1/2-ton trucks 1969–89 Dodge 1/2-ton
trucks with manual hubs 1990–93 Dodge trucks
with Dana 44 automatic hubs
1990–93 Dodge trucks
with Dana 60 manual hubs
1988–95 Isuzu Trooper, Rodeo,
Amigo, and pickup; 1989–95
Honda Passport; and Jeep J20
pickups with Dana 60 axle
7157 T83T-1197-B
205-192
7270A T86T-1197-AR
205-244
205-448
7090A
N/A
N/A
7157
N/A
N/A
7158
N/A
N/A
6283
N/A
N/A
7157
N/A
N/A
7157
N/A
N/A
7270A
N/A
N/A
1928
N/A
N/A
1982–97 Toyota trucks, models
FJ, LN, RN, with 54 mm 6 pt. nuts 7612
N/A
N/A
N/A
N/A
7941
N/A
N/A
7913
N/A
N/A
1995–2002 4WD Toyota Tacoma
and 1996-2002 4WD Toyota
T100 and 4Runner, all with
lockout hubs 1997–2000 4WD Geo Tracker
and Suzuki Samurai
Similar to Kent-Moore
No. J-42119
7612
2-1/8"
54 mm
7941
2.366 center to
center on pins
6006
1-11/16"
43 mm
205-230
205-282
N/A
7698
7913
205-D065
205-D065
2003–newer Ford F-250, 350, 450
Super Duty w/10-1/2" rear axle
6601
Similar to Ford
No. 205-448
205-D001
7158 D85T-1197-A
1985 and 2002 Ford F-series
T85T-4252-AH
3/4- and 1-ton truck with Dana 80 rear axle
7269 T88T-4252-A
6601
2-3/4" 0.D.
6064
1.972 center to
center on pins
1902
2-3/8"
1928
2-9/16"
1936
2-3/8"
6283
2-29/64"
159
AUTOMOTIVE SPECIAL TOOLS
Locknut Sockets
7-Piece Wheel Bearing Locknut Socket Set
• For use with 1/2" ratchet or breaker bar.
Set contains:
No. 519097-7 – 55 mm hex locknut socket designed for use
on front wheel adjusting nuts found on Toyota models FJ,
LN, and RN.
No. 519097-1 – 2-3/8" hex locknut socket works on 1984–92
Ford Rangers and Bronco IIs with automatic
locking hubs. Similar to Ford No. 205-040 (T70T-4252-B).
No. 519097-3 – 2-1/2" hex locknut socket fits the hex nut
found on rear axles and various front axle applications on
light-duty trucks.
No. 519097-5 – 2-1/2" rounded hex locknut socket works
on 1995–96 Ford F-150 trucks and full-sized Broncos with
automatic locking hubs. Similar to Ford No. 205-348
(T95T-1197-A).
No. 519097-4 – 2-3/4" rounded hex locknut socket works
on 3/4-ton and 1-ton Ford F-250 and F-350 trucks with
automatic locking hubs. Similar to Ford No. 205-349
(T95T-1197-B).
No. 519097-2 – 2-9/16" rounded hex locknut socket works
on 1990–93 Dodge trucks with Dana 60 manual hubs.
No. 519097-6 – 2-3/8" rounded hex locknut socket works on
1990–newer Ford Rangers, Bronco IIs, and Explorers with
automatic locking hubs.
No. 4542 – Wheel bearing locknut socket set (7 piece).
Wt., 11 lbs., 7 oz.
4542
Axle Nut Socket Set – FWD (7 piece)
• Extra long, 1/2" drive chrome molybdenum sockets for heavy-duty use in removing and installing axle nuts.
with a ratchet, breaker bar, or torque wrench.
•
• Contained in a blow-molded plastic storage case.
Contents of set:
No. 4547-29 – 29 mm socket services various late model
GM, Ford, and Asian imports.
No. 4547-30 – 30 mm socket services GM body styles A, J,
and N, plus Asian imports.
No. 4547-32 – 32 mm socket services late model Honda and
Chrysler vehicles.
No. 4547-34 – 34 mm socket services many GM mid-size
vehicles.
No. 4547-35 – 35 mm socket services many GM vehicles.
No. 4547-36 – 36 mm socket services many GM, Ford, and
Chrysler full-size vehicles.
No. 4547-38 – 38 mm socket services various full-size
vehicles including SUVs.
No. 4547 – Axle nut socket set (7 piece).
Wt., 10 lbs., 6 oz.
Use
4547
160
AUTOMOTIVE SPECIAL TOOLS
Locknut Sockets
Locknut Socket Set – 4WD (6 piece)
• Chrome vanadium steel sockets cover most SUV and
light truck applications.
have 1/2" square drive, allowing use of a
•
torque wrench, ratchet, or breaker bar.
Contents of set:
No. 4543-1 – Toyota 4-lug locknut socket. Services
high-torque locknuts on Toyota 4WD vehicles having
free-wheel (lock out) hubs: 1995–newer Tacoma; 1996–
newer T100 and 4Runner.
No. 4543-2 – Ford 4-lug locknut socket for high-shear
rotating nuts on 1985–newer F-250 and F-350 truck
rear axles, and Dana 80 rear axles of Ford Super Duty
trucks.
No. 4543-3 – 4-lug socket for removing and installing
4-slot front axle locknuts on 1986–newer F-Series 1/2ton trucks, full-size Bronco with Dana 44 axle, 1984–92
Ford Ranger, and Bronco II with manual hubs. Also,
Dodge trucks using Dana 44 axle with automatic hubs.
No. 4543-4 – 6-lug socket for removing and installing
4-slot front axle locknuts on 1978–84 Ford F-Series
4WD heavy-duty 3/4- and 1-ton trucks; 1973–81 GM
4WD 3/4- and 1-ton trucks.
No. 4543-5 – 4-lug socket for removing and installing
4-slot front axle locknuts on 1993–newer Ford Ranger,
Bronco II, and Explorer with manual hubs; 1995–newer
F-Series 1/2-, 3/4-, and 1-ton trucks and full-size Bronco
with manual hubs; 1959–85 F-Series 1/2- and 3/4-ton
trucks and full-size Bronco; 1960–90 GM 1/2-ton trucks
and full-size Blazer/Jimmy; 1969–72 International 1/2-ton
trucks; 1969–89 Dodge 1/2-ton trucks with manual hubs.
No. 4543-6 – FWD front spindle puller. Removes front
spindle to access needle bearing, when lubricating and
aligning front wheels. 5/8"-18 fine thread permits use
with OTC No. 1155 slide hammer. Fits spindle thread
sizes 2"-16, 1-5/8"-16 and 38 mm-1.5. Applications:
Full-size GM, Ford, Jeep, and International pickups with
Dana front axles, plus Ranger and Bronco II.
• A blow-molded plastic storage case keeps set contents
organized and protected from loss.
No. 4543 – 4WD spindle nut socket set (6 piece).
Wt., 13 lbs.
Sockets
4543
161
AUTOMOTIVE SPECIAL TOOLS
Locknut Sockets & Brake Service
1/2" Drive Locknut Socket Set
• These are not light-hearted sockets; they feature a 1/2"
6010
6612, 6902, 6921
6795, 6796, 6928, 6936
square drive, and can be used with an extension and
torque wrench for accurate tightening.
• For use on the rounded and standard hex nuts found on
the most popular light-duty trucks on the road.
• Unlike the competition, these sockets are®backed by the
famous OTC Lifetime Marathon Warranty against defects
in materials and workmanship.
No. 6010 – Locknut socket set. Includes one each: Nos.
6612, 6795, 6796, 6902, 6921, 6928, 6936. Wt., 12 lbs.
Set includes one each of the following:
No. 6612 – 54 mm hex locknut socket designed for use on
front wheel adjusting nuts found on Toyota FJ, LN, and RN
models. Wt., 1 lb., 8 oz.
No. 6902 – 2-3/8" hex locknut socket works on 1984–92
Ford Rangers and Bronco IIs with automatic locking hubs.
(Ford No. T70T-4252-B and 205-040). Wt., 1 lb., 8 oz.
No. 6921 – 2-1/2" hex locknut socket fits hex nut found on
rear axles and various front axle applications on light-duty
trucks. Wt., 1 lb., 8 oz.
No. 6795 – 2-1/2" rounded hex locknut socket. Works on
1995–96 Ford F-150 trucks and full-sized Broncos with
automatic locking hubs. (Ford No. T95T-1197-A and
205-348). Wt., 1 lb., 8 oz.
No. 6796 – 2-3/4" rounded hex locknut socket. Works on
3/4- and 1-ton Ford F-250 and F-350 trucks with automatic
locking hubs. (Ford No. T95T-1197-B and 205-349).
Wt., 1 lb., 8 oz.
No. 6928 – 2-9/16" rounded hex locknut socket. Works on
1990–93 Dodge trucks with Dana 60 manual hubs.
Wt., 1 lb., 8 oz.
No. 6936 – 2-3/8" rounded hex locknut socket. Works on
1990–newer Ford Rangers, Bronco IIs, and Explorers with
automatic locking hubs. Wt., 1 lb., 8 oz.
Brake Pressure Test Kit
Kit contains a complete set of fittings and gauges for
pressure testing ABS and conventional brake systems on
Chrysler, Ford, GM, Jeep, and import vehicles.
• Includes an organizer case
No. 7488A – Brake pressure test kit. Includes two
0–3,000 psi gauges, 16 adapter fittings, two Bosch ABS
adapters, one Teves/Delco Powermaster III adapter,
one Ford (Teves) adapter, one 90° elbow fitting, one 45°
elbow fitting, bleeder, and instructions.
Wt., 7 lbs., 10 oz.
7488A
162
AUTOMOTIVE SPECIAL TOOLS
Brake Service
Brake Fluid Safety Meter
Check condition of brake fluid in less than a minute!
Water can enter a brake system though microscopic holes
anywhere in the system. Once inside, it can cause corrosion
in system components...it can vaporize under the high heat
conditions of hard braking situations...it can cause dangerous degradation of your customer’s ability to stop safely!
The No. 3890 can diagnose a brake system in under a
minute. It actually boils a small sample of brake fluid in
the reservoir to test for water contamination.
FEATURES:
• Powered by the vehicle battery; won’t operate if
connected to the wrong polarity.
• On-screen prompts lead you quickly through testing.
• You’ll find the minimum boiling (vaporizing) point along
with minimum recommended levels for various types of
brake fluid.
• Works on DOT 3, DOT 4, and DOT 5.1 fluids.
• No consumable test strips; buy this tool and test every
vehicle that comes into your shop.
No. 3890 – Brake fluid safety meter. Wt., 2 lbs., 8 oz.
3890
Specifications:
Accuracy at 212°–356°F....1% typical, 3% max.
Accuracy above 356°F....3% typical, 5% max.
Testing Time....15–60 seconds
Operating Temp Range....32°–122°F
Steering Wheel Holder & Pedal Depressor Kit
• This kit has two applications: 1) holds steering wheel in
position for alignment adjustments, and 2) depresses
brake pedal for various brake checks, including brake
lamp operation.
• Rod easily slides in actuator for fast, easy installation
of tool on brake pedal or steering wheel. Simply hand
squeeze the actuator to accomplish fine adjustments.
• Kit includes: actuator assembly; extension rod for
actuator (use when depressing brake pedal); hook
assembly (hooks on steering wheel when depressing
brake pedal or holding steering wheel); and flat pad (rests
on front seal when holding steering wheel).
No. 4546 – Steering wheel holder and pedal depressor kit.
Wt., 5 lbs., 2 oz.
No. 4546-1 – Handle and Rod. Wt., 2 lbs.
No. 4546-2 – Steering Wheel and Pedal Holder.
Wt., 2 lbs., 7 oz.
4546
One-Man Brake Bleeder Hose
• Removes air from brake system, one wheel at a time, and
eliminates the need for an assistant.
easily attaches to bleeder screw, which holds hose
•
in place and prevents leaking.
• Check valve on end of hose prevents air from entering
brake system when pumping brake pedal.
No. 4599 – One-man brake bleeder hose. Wt., 5 oz.
Hose
4599
163
AUTOMOTIVE SPECIAL TOOLS
Brake Service
Fluid Evacuation / Brake Bleeding Tools
•Use to bleed brake systems and remove a variety of fluid from vehicles, such as antifreeze, oil, transmission fluid, gear lube, etc.
•Quick connect locking hose adapters and ball-style on/off
valve on hose prevent fluid leakage.
•Equipped with a relief valve to prevent over-pressurizing the tank.
8101
8100
7853
Similar to KentMoore J-35856
7317A
No. 8100 – Operates by shop air or a hand pump; shipped
complete with a brake bleeding hose, fluid evacuation hose,
and two suction hoses (6 mm and 7 mm); 10-liter capacity
tank. Wt., 10 lbs.
No. 8101 – Operates with shop air; shipped with a brake
bleeding hose and fluid evacuation hose; 6-liter capacity tank.
Wt., 10 lbs., 13 oz.
ABS Brake Proportioning Valve Depressor
The proportioning valve depressor works on various GM utility
vehicles, vans, and pickups fitted with Kelsey Hayes anti-lock
brake systems. It also works on rear-wheel anti-lock brakes.
• Two depressors work best for four-wheel anti-lock
systems.
No. 7853 – ABS brake proportioning valve depressor. Wt., 4 oz
Disc Park Brake Caliper Tool Kit
This tool set is a must when you’re installing brake pads
on vehicles with 4-wheel disc brakes. It works on most GM
vehicles, most Ford vehicles, and imported vehicles.
• Includes tool to retract the piston on a parking brake actuator.
No. 7317A – Disc park brake caliper tool kit. Wt., 4 lbs., 5 oz.
Kit includes one each of the following:
No. 214963 – Plate.
No. 214964 – 3/8" extension.
No. 308649 – Forcing screw.
No. 308644 – Disc brake adapter tool for 1-1/2" pistons. Usable
two ways: one side fits Dodge Conquest, Ford, GM, Honda,
Mazda, and Mitsubishi; other side fits Pontiac Fiero, Subaru,
and Toyota. Wt., 3 oz.
No. 308645 – Four wheel disc brake adapter tool. Fits
1-11/16" pistons on Subaru, Nissan, Datsun, and Ford
Thunderbird. Wt., 5 oz.
No. 308646 – Disc brake adapter tool for GM vehicles with
1-7/8" pistons. Wt., 5 oz.
No. 308647 – Disc brake adapter tool for GM vehicles with
2-1/8" pistons. Wt., 7 oz.
No. 308648 – Disc brake adapter tool for GM vehicles with
2-1/2" pistons. Wt., 10 oz.
Disc Brake Piston Tool
• This “cube” tool rotates pistons back into brake calipers when
4589
164
replacing brake pads on vehicles with rear wheel disc brakes.
• Tool has 3/8" square drive, provides six drive pin con-
figurations to fit most cars and light trucks. This updated version
fits more applications than many competitors’ tools.
No. 4589 – Disc brake piston tool. Wt., 3 oz.
AUTOMOTIVE SPECIAL TOOLS
Brake Service
Universal Brake Caliper Bit Socket Set
(9 Piece)
No. 6135 – Universal brake caliper bit socket set (9 piece).
Wt., 1 lb. 8 oz.
Set includes one each of the following:
No. 6107 – Size T40, sq. drive 3/8"
No. 6108 – Size T45, sq. drive 3/8"
No. 6110 – Size T50, sq. drive 3/8"
No. 6112 – Size T60, sq. drive 1/2"
No. 6165 – Size 1/4", sq. drive 3/8"
No. 6167 – Size 3/8", sq. drive 3/8"
No. 6175 – Size 7 mm, sq. drive 3/8"
No. 6176 – Size 8 mm, sq. drive 3/8"
No. 6177 – Size 10 mm, sq. drive 3/8"
6135
Caliper Hanger Set
7661
These hangers are designed to hold brake calipers out of
your way during brake, bearing, suspension, or axle work. In
doing so, they make the jobs easier and faster, and reduce
possible brake hose damage.
No. 7661 – Caliper hanger set. Wt., 8 oz.
Hub Resurfacing Kit
• Fits your power drill to quickly sand rust off
lug studs and rotors on the hub assembly.
Sanding pads attach with Velcro™.
• For most domestic and import vehicles
with either front or rear disc brakes. Includes
holder and five sanding discs.
• Run at speeds of 1200 rpm or less for best
results. (Do not exceed 1200 rpm).
No. 7942A – Hub resurfacing kit.
Wt., 3 oz.
No. 222548 – 10 pack of replacement sanding
pads for No. 7942A. Wt.,1 oz.
No. J-42450-9 – Holder only. Wt., 2 oz.
7942A
Disc Brake Pad Spreader
• Works on:
1998–2001 Chev. Lumina
1998–2004 Chev. Monte Carlo
2000–2004 Chev. Impala
1998–2004 Buick Regal
1998–1999 Olds Cutlass
1998–2004 Pontiac Grand Prix
1997–2004 Ford F-250, F-300, F-450 trucks
• Can be used on or off the vehicle during brake pad
replacement to push the piston back into the caliper.
Thick pushing plate (3/16") and wide, threaded collars are
designed for heavy-duty applications.
No. 6093 – Disc brake pad spreader. Wt., 2 lbs. 3 oz.
6093
165
AUTOMOTIVE SPECIAL TOOLS
Brake Service
Disc Brake Pad Spreader
7034
Similar to Ford
No. 206-D001
(D79L-2196-A)
Disc brake pad installation is much easier when you’re
using this spreader, which fits between the new pads and
expands to retract the piston. This leaves your hands free
to slide the caliper over the rotor. Designed to work on
standard and four-piston caliper disc brakes, this tool will
shorten installation time.
No. 7034 – Disc brake pad spreader. Wt., 10 oz.
Ford Brake Spring Tool
Similar to Ford
No. 206-008
(T73T-2300-A)
7456
The hold-down springs on rear brake drums can now
be easily removed or installed with the help of this tool
– without causing damage or injuries.
• For use on 1967 to 2004 3/4- and 1-ton pickups and
vans.
No. 7456 – Ford brake spring tool. Wt., 7 oz.
Ford Caliper Pin Remover
Similar to Ford No. 206-0004
(T73T-2300-A)
(D89T-2196-A)
7299
This is the damage-free way to remove brake caliper
pins on 1986 to ’88 Aerostar, Bronco, and E- and F-series
pickups; 1983 to ’88 Ranger; and 1984 to ’88 Bronco II.
No. 7299 – Ford caliper pin remover. Wt., 7 oz.
Ford Disc Brake Caliper Pin Remover
7499
Forget those makeshift methods of disc brake caliper pin
removal. With one of these tools, you can handle jobs on
a variety of light-duty Ford models.
• For use on 1989 to 1996 Aerostar, Bronco, Ranger,
E- and F-series pickups; 1989 to ’91 Bronco II; and 1991
to 1995 Explorer.
No. 7499 – Ford disc brake caliper pin remover. Wt., 8 oz.
GM W-Body Brake Bushing Service Set
7639
Similar to
Kent-Moore
J-39495
Here’s the complete set for servicing seized disc-brake
rear-caliper slides on GM W-body cars. It includes a bushing driver, 180 grit hone, and a 1-1/4" diameter wire brush.
• For use on 1988 to 1993 Buick Regal, Oldsmobile
Cutlass Supreme, Pontiac Grand Prix; 1990 to 1993
Chevrolet Lumina sedan.
No. 7639 – GM W-body brake bushing service set.
Wt., 13 oz.
3-in-1 180° Tubing Bender
• Capable of making 180° bends in copper, brass,
6515
166
aluminum, and steel tubing.
one tool works on three sizes of tubing: 1/4", 5/16",
•
and 3/8".
No. 6515 – 3-in-1 180° tubing bender. Wt., 1 lbs., 5 oz.
Just
AUTOMOTIVE SPECIAL TOOLS
Brake Service
Heavy-Duty Tubing Cutter
• Works on tubing sizes 1/8" to 1-1/8" O.D.
(3 mm to 29 mm).
cuts copper, brass, aluminum, and steel brake lines.
•
• Ream folds onto cutter body for storage.
• Extra cutting wheel stored under ream.
No. 6512 – Heavy-duty tubing cutter. Wt., 6 oz.
Easily
6512
Mini Tubing Cutter
• Works on tubing sizes 1/8" to 5/8" O.D. (3 mm to 16 mm).
• Easily cuts copper, brass, aluminum, and steel brake lines
in hard-to-reach places.
folds onto cutter body for storage.
•
• Extra cutting wheel stored under ream.
No. 6514 – Mini tubing cutter. Wt., 3 oz.
Ream
6514
Brake Drum and Rotor Remover
Having trouble pulling brake drums off hubs? This tool is the
solution for that common problem.
• For use on Mercury Villager vans and many import
vehicles.
• The No. 6021 tools simply thread into the 8 mm x 1.25
holes in the drum, then are tightened simultaneously to
free the hub from the drum. Then the handles are used to
pull off the drum.
No. 6021 – Brake drum and rotor remover. Wt., 5 oz.
6021
Brake Tool Set (8 piece)
• Set contains the most popular brake tools for servicing
drum brakes on many import and domestic vehicles.
BMC and high quality handles.
•
• Includes three different brake spoons to adjust most brake
drums, five different brake spring tools that will service
most drum brakes.
No. 6516 – Brake tool set. Wt., 3 lbs. 2 oz.
Features
6516
GM Code Retrieval Keys
These keys enable you to easily retrieve trouble codes from
pre-OBDIl GM vehicles.
No. 7739 – ECM code retrieval key. Jumps between A and
B terminals on ALDL connector. Wt., 2 oz.
7739
167
AUTOMOTIVE SPECIAL TOOLS
Brake Service & Flaring Tools
GM Brake Shoe Spanner and Spring Remover
Our brake shoe spanner and spring remover tool is essential
for removing the rear brake shoe retaining springs. It also
removes and installs adjuster springs, and can be used to
activate the brake self-adjuster mechanism.
• For use on 1991 to 1997 H-body, 1992 to 1997 C- and
U-body vehicles, and 1995 and newer Chevrolet Monte
Carlo and Lumina.
No. 6631 – GM brake shoe spanner and spring remover.
Wt., 11 oz.
6631
Brake Spring Pliers and Claw
• Effectively removes and replaces shoe return springs of
drum brakes on domestic cars and trucks. Thin, narrow
point provides straight, in-line pull on spring.
• Robust handle provides powerful leverage. Double-ended
design. Plated steel resists corrosion.
No. 4590 – Brake spring pliers and claw. Wt., 14 oz.
4590
Brake Spring Compressor Tool
• Provides leverage to remove and install stubborn hold
down springs of drum brakes on cars and light trucks.
beveled cup end and notched design grips the
•
retaining washers (11/16" to 7/8") used to hold the springs
in place. Comfortable handle and knurled base for solid
gripping.
No. 4591 – Brake spring compressor tool. Wt. 3 oz.
Special
4591
Double Flaring Tool Set with Cutter
• Designed for steel brake lines where double flaring is
6503
168
required.
• Also performs 45° single flares on 3/16", 1/4", 3/8", 7/16",
1/2", and 5/8" copper, aluminum, brass, and magnesium
tubing.
• Includes the No. 6514 tubing cutter and adapters for
double flaring 3/16", 1/4", 5/16", 3/8", and 1/2" tubing.
• Housed in a plastic blow-molded case.
No. 6503 – Double flaring tool set with cutter.
Wt., 3 lbs., 7 oz.
AUTOMOTIVE SPECIAL TOOLS
Flaring Tools
Bubble (I.S.O.) Flaring Tool Set with Cutter
• Designed for metric, steel brake lines where an ISO or
bubble flare is required.
the No. 6514 tubing cutter and adapters for
•
4.75 mm, 6 mm, 8 mm, and 10 mm tubing.
• Housed in a plastic blow-molded case.
No. 6504 – Bubble (I.S.O.) flaring tool set with cutter.
Wt., 3 lbs., 7 oz.
Includes
6504
Metric Double Flaring Tool Set with Cutter
• Designed for metric, steel brake lines where double flaring
is required.
performs 45° single flares on 4 mm, 4.75 mm, 6 mm,
•
8 mm, 10 mm, 12 mm, and 14 mm copper, aluminum,
brass, and magnesium tubing.
• Includes the No. 6514 tubing cutter and adapters for double
flaring 4 mm, 4.75 mm, 6 mm, 8 mm, and 10 mm tubing.
• Housed in a plastic blow-molded case.
No. 6506 – Metric double flaring tool set with cutter.
Wt., 3 lbs., 7 oz.
Also
6506
Double Flaring Tool Kit
• Designed for double or single flare in copper,
aluminum, soft steel brake line, and brass tubing
(to 45 degrees).
• Includes five adapters 3/16" through 1/2"
(4.8 mm through 12.7 mm).
• Chrome swivel, made of alloy steel, reduces friction.
Forged yoke made of heat-treated steel. Housed in a
blow-molded storage case.
No. 4503 – Double flaring tool kit. Wt., 2 lbs., 10 oz.
4503
Bubble (I.S.O.) Flaring Tool Kit
• Designed for crack-free bubble flares on soft
steel tubing used in automotive brake systems.
four dies: 4.75, 6, 8, and 10 mm adapters.
•
• Forged steel yoke, flaring bar, and all the adapters needed
for ISO bubble flaring.
• The most economical “Bubble” flare tool to date. Housed
in a blow-molded storage.
No. 4504 – Bubble (I.S.O.) flaring tool kit. Wt., 2 lbs., 10 oz.
Includes
4504
169
AUTOMOTIVE SPECIAL TOOLS
Torx Bit Sockets
Master TORX® Socket Set
51-piece, professional socket set in a blow-molded case.
5900A
Master Torx Socket Set includes:
TORX® Bit Socket Set
T6 to T60 (14 piece)
No.
5906
5908
6101
6102
6103
6104
6105
No.
Size
T6
T8
T10
T15
T20
T25
T27
Size
Sq. Drive
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
Sq. Drive
TORX PLUS® Bit Sockets
TP8 to TP60 (12 piece)
No.
5918
6181
6182
6183
6184
6185
Size
TP8
TP10
TP15
TP20
TP25
TP27
Sq. Drive
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
6106
6107
6108
6109
6110
6111
6112
No.
6186
6187
6188
6191
5915
5916
T30
T40
T45
T47
T50
T55
T60
Size
TP30
TP40
TP45
TP50
TP55
TP60
Hundreds of applications from front to rear on cars and trucks:
– seat belt bolts
– interior and exterior trim screws
– engine assemblies
– tail lamp lenses & assemblies
– bumpers
– headlight bezels
– door strikers & latches
– brake rotor bolts
– GM front-wheel drive front wheel bearings
– truck box liners
• Styles available: TORX bit sockets, TORX PLUS bits sockets, tamper-resistant TORX bits, and TORX sockets for external bolts.
• Made from superior S2 steel to meet or exceed torque
specifications.
No. 5900A – Master TORX® socket set. 51-piece set in
blow-molded case. Wt., 7 lbs.
1/4"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
Sq. Drive
1/4"
3/8"
3/8"
3/8"
3/8"
1/2"
TORX® External Socket
E4 to E24 (13 piece)
No.
5934
5935
6151
6152
6153
6154
6155
Size
E4
E5
E6
E7 E8
E10
E12
Sq. Drive
1/4"
1/4"
1/4"
1/4"
1/4"
3/8"
3/8"
No.
6156
6157
5936
5937
5938
5939
TORX® Tamper-Resistant Bits
TT8 to TT60 (12 piece)
No
5919
5920
5921
5922
5923
5924
Size Hex Insert
TT8
1/4"
TT10
1/4"
TT15
1/4"
TT20
1/4"
TT25 1/4"
TT27
1/4"
No
5925
5926
5927
5928
5929
5930
Size
E14
E16
E18
E20
E22
E24
Size
TT30
TT40
TT45
TT50
TT55
TT60
Sq. Drive
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
Hex Insert
1/4"
3/8"
3/8"
3/8"
3/8"
1/2"
TORX® Bit Socket Set (12 Piece)
No. 6100 – TORX® bit socket set (12 piece).
Wt., 1 lb. 3 oz.
Set includes one each of the following:
6100
170
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
6101 – Size T10, Sq. Drive 1/4"
6102 – Size T15, Sq. Drive 1/4"
6103 – Size T20, Sq. Drive 1/4"
6104 – Size T25, Sq. Drive 1/4"
6105 – Size T27, Sq. Drive 1/4"
6106 – Size T30, Sq. Drive 1/4"
6107 – Size T40, Sq. Drive 3/8"
6108 – Size T45, Sq. Drive 3/8"
6109 - Size T47, Sq. Drive 3/8"
6110 – Size T50, Sq. Drive 3/8"
6111 – Size T55, Sq. Drive 3/8"
6112 – Size T60, Sq. Drive 1/2"
TORX®
AUTOMOTIVE SPECIAL TOOLS
Torx Bit Sockets
TORX® Tamper-Resistant Bit Set (8 Piece)
No. 6145 – TORX® tamper-resistant bit set (8 piece).
Wt., 4 oz.
Set includes one each of the following:
No. 6141 – Size T10H, Hex Insert 1/4"
Tamper
No. 6142 – Size T15H, Hex Insert 1/4"
Resistant
No. 6143 – Size T20H, Hex Insert 1/4"
TORX®
No. 6144 – Size T25H, Hex Insert 1/4"
No. 6146 – Size T27H, Hex Insert 1/4"
No. 6147 – Size T30H, Hex Insert 1/4"
No. 6148 – Size T40H, Hex Insert 1/4"
No. 6130 – Sq. Drive 1/4", Bit Holder 1/4"
6145
TORX PLUS® Bit Socket Set (9 Piece)
No. 6180 – TORX PLUS® bit socket set (9 piece).
Wt., 11 oz.
Set includes one each of the following:
No. 6181 – Size TP10, Sq. Drive 1/4"
TORX
No. 6182 – Size TP15, Sq. Drive 1/4"
®
PLUS
No. 6183 – Size TP20, Sq. Drive 1/4"
No. 6184 – Size TP25, Sq. Drive 1/4"
No. 6185 – Size TP27, Sq. Drive 1/4"
No. 6186 – Size TP30, Sq. Drive 1/4"
No. 6187 – Size TP40, Sq. Drive 3/8"
No. 6188 – Size TP45, Sq. Drive 3/8"
No. 6191 – Size TP50, Sq. Drive 3/8"
6180
TORX® Socket Set
(For External Bolts; 7 Piece)
No. 6150 – TORX® socket set for external bolts
(7 piece). Wt., 10 oz.
Set includes one each of the following:
No. 6151 – Size E6, Sq. Drive 1/4"
TORX®
No. 6152 – Size E7, Sq. Drive 1/4"
No. 6153 – Size E8, Sq. Drive 1/4"
No. 6154 – Size E10, Sq. Drive 3/8"
No. 6155 – Size E12, Sq. Drive 3/8"
No. 6156 – Size E14, Sq. Drive 3/8"
No. 6157 – Size E16, Sq. Drive 3/8"
6150
Universal Brake Caliper Bit Socket Set
(9 Piece)
No. 6135 – Universal brake caliper bit socket set
(9 piece). Wt., 1 lb. 8 oz.
Set includes one each of the following:
No. 6107 – Size T40, Sq. Drive 3/8"
TORX®
No. 6108 – Size T45, Sq. Drive 3/8"
No. 6110 – Size T50, Sq. Drive 3/8"
No. 6112 – Size T60, Sq. Drive 1/2"
No. 6165 – Size 1/4", Sq. Drive 3/8"
No. 6167 – Size 3/8", Sq. Drive 3/8"
HEX
No. 6175 – Size 7 mm, Sq. Drive 3/8"
No. 6176 – Size 8 mm, Sq. Drive 3/8"
No. 6177 – Size 10 mm, Sq. Drive 3/8"
6135
171
AUTOMOTIVE SPECIAL TOOLS
Torx Bit Sockets
Hex Bit Socket Set (Fractional; 7 Piece)
No. 6160 – Hex bit socket set (Fractional; 7 piece).
Wt., 1 lb.
Set includes one each of the following:
No. 6161 – Size Hex 1/8", Sq. Drive 3/8"
No. 6162 – Size Hex 5/32", Sq. Drive 3/8"
HEX
No. 6163 – Size Hex 3/16", Sq. Drive 3/8"
No. 6164 – Size Hex 7/32", Sq. Drive 3/8"
No. 6165 – Size Hex 1/4", Sq. Drive 3/8"
No. 6166 – Size Hex 5/16", Sq. Drive 3/8"
No. 6167 – Size Hex 3/8", Sq. Drive 3/8"
6160
Hex Bit Socket Set (Metric; 7 Piece)
No. 6170 – Hex bit socket set (Metric; 7 piece).
Wt., 1 lb.
Set includes one each of the following:
No. 6171 – Size Hex 3 mm, Sq. Drive 3/8"
HEX
No. 6172 – Size Hex 4 mm, Sq. Drive 3/8"
No. 6173 – Size Hex 5 mm, Sq. Drive 3/8"
No. 6174 – Size Hex 6 mm, Sq. Drive 3/8"
No. 6175 – Size Hex 7 mm, Sq. Drive 3/8"
No. 6176 – Size Hex 8 mm, Sq. Drive 3/8"
No. 6177 – Size Hex 10 mm, Sq. Drive 3/8"
6170
Individually sold items.
TORX® Bits
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
5906 – Size T6, Sq. Drive 1/4"
5908 – Size T8, Sq. Drive 1/4"
6121 – Size T10, Hex Insert 1/4"
6122 – Size T15, Hex Insert 1/4"
6123 – Size T20, Hex Insert 1/4"
6124 – Size T25, Hex Insert 1/4"
6125 – Size T27, Hex Insert 1/4"
6126 – Size T30, Hex Insert 1/4"
6127 - Size T40, Hex Insert 5/16"
6128 – Size T45, Hex Insert 5/16"
6114 – Size T47, Hex Insert 5/16"
6129 – Size T50, Hex Insert 5/16"
6117 – Size T55, Hex Insert 7/16"
6119 – Size T60, Hex Insert 1/2"
172
TORX PLUS® Bits
TORX®
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
5918
6132
6133
6134
6158
6159
6168
6169
6178
6194
5915
6195
5916
6196
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Size TP8, Sq. Drive 1/4"
Size TP10, Hex Insert 1/4"
Size TP15, Hex Insert 1/4"
Size TP20, Hex Insert 1/4" TORX®
PLUS
Size TP25, Hex Insert 1/4"
Size TP27, Hex Insert 1/4"
Size TP30, Hex Insert 1/4"
Size TP40, Hex Insert 5/16"
Size TP45, Hex Insert 5/16"
Size TP50, Hex Insert 5/16"
Size TP55, Sq. Drive 3/8"
Size TP55, Hex Insert 7/16"
Size TP60, Sq. Drive 1/2"
Size TP60, Hex Insert 1/2"
AUTOMOTIVE SPECIAL TOOLS
Torx Bit Sockets
TORX® Tamper-Resistant Bits
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
5919
5920
5921
5922
5923
5924
5925
5926
5927
5928
5929
5930
6141
6142
6143
6144
6146
6147
6148
6149
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Size TT8, Hex Insert 1/4"
Size TT10, Hex Insert 1/4"
Size TT15, Hex Insert 1/4"
Size TT20, Hex Insert 1/4"
Size TT25, Hex Insert 1/4"
Size TT27, Hex Insert 1/4"
Size TT30, Hex Insert 1/4"
Size TT40, Hex Insert 3/8"
Size TT45, Hex Insert 3/8"
Size TT50, Hex Insert 3/8"
Size TT55, Hex Insert 3/8"
Size TT60, Hex Insert 1/2"
Size T10H, Hex Insert 1/4"
Size T15H, Hex Insert 1/4"
Size T20H, Hex Insert 1/4"
Size T25H, Hex Insert 1/4"
Size T27H, Hex Insert 1/4"
Size T30H, Hex Insert 1/4"
Size T40H, Hex Insert 1/4"
Size T45H, Hex Insert 5/16"
TORX® Bit Sockets
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
6101 – Size T10, Sq. Drive 1/4"
6102 – Size T15, Sq. Drive 1/4"
6103 – Size T20, Sq. Drive 1/4"
6104 – Size T25, Sq. Drive 1/4"
6105 – Size T27, Sq. Drive 1/4"
6106 – Size T30, Sq. Drive 1/4"
6107 – Size T40, Sq. Drive 3/8"
6108 – Size T45, Sq. Drive 3/8"
6109 - Size T47, Sq. Drive 3/8"
6110 – Size T50, Sq. Drive 3/8"
6111 – Size T55, Sq. Drive 3/8"
6112 – Size T60, Sq. Drive 1/2"
TORX PLUS® Bit Sockets
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
6181
6182
6183
6184
6185
6186
6187
6188
6191
6192
6193
–
–
–
–
–
–
–
–
–
–
–
Size TP10,
Size TP15,
Size TP20,
Size TP25,
Size TP27,
Size TP30,
Size TP40,
Size TP45,
Size TP50,
Size TP55,
Size TP60,
Sq.
Sq.
Sq.
Sq.
Sq.
Sq.
Sq.
Sq.
Sq.
Sq.
Sq.
Drive
Drive
Drive
Drive
Drive
Drive
Drive
Drive
Drive
Drive
Drive
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
3/8"
1/2"
Bit Holders
No.
No.
No.
No.
6130 – Sq. Drive 1/4", Bit Size 1/4"
6131 – Sq. Drive 3/8", Bit Size 5/16"
6136 – Sq. Drive 3/8", Bit Size 7/16"
6113 – Sq. Drive 1/2", Bit Size 1/2"
Hex Bit Sockets (Fractional)
No.
No.
No.
No.
No.
No.
No.
6161
6162
6163
6164
6165
6166
6167
–
–
–
–
–
–
–
Size
Size
Size
Size
Size
Size
Size
Hex
Hex
Hex
Hex
Hex
Hex
Hex
1/8", Sq. Drive 3/8"
5/32", Sq. Drive 3/8"
3/16", Sq. Drive 3/8"
7/32", Sq. Drive 3/8"
1/4", Sq. Drive 3/8"
5/16", Sq. Drive 3/8"
3/8", Sq. Drive 3/8"
Hex Bit Sockets (Metric)
No.
No.
No.
No.
No.
No.
No.
6171
6172
6173
6174
6175
6176
6177
–
–
–
–
–
–
–
Size
Size
Size
Size
Size
Size
Size
Hex
Hex
Hex
Hex
Hex
Hex
Hex
3 mm, Sq. Drive 3/8"
4 mm, Sq. Drive 3/8"
5 mm, Sq. Drive 3/8"
6 mm, Sq. Drive 3/8"
7 mm, Sq. Drive 3/8"
8 mm, Sq. Drive 3/8"
10 mm, Sq. Drive 3/8"
TORX® Sockets for External Bolts
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
No.
5934
5935
6151
6152
6153
6154
6155
6156
6157
5936
5937
5938
5939
–
–
–
–
–
–
–
–
–
–
–
–
–
Size
Size
Size
Size
Size
Size
Size
Size
Size
Size
Size
Size
Size
E4, Sq. Drive 1/4"
E5, Sq. Drive 1/4"
E6, Sq. Drive 1/4"
E7, Sq. Drive 1/4"
E8, Sq. Drive 1/4"
E10, Sq. Drive 3/8"
E12, Sq. Drive 3/8"
E14, Sq. Drive 3/8"
E16, Sq. Drive 3/8"
E18, Sq. Drive 3/8"
E20, Sq. Drive 3/8"
E22, Sq. Drive 1/2"
E24, Sq. Drive 1/2"
173
AUTOMOTIVE SPECIAL TOOLS
Ribe Key, Seat Belt Tool
Ribe Key Set
• These keys work on late model Volkswagen, Audi,
Lancer, Fiat, and Lancia vehicles.
bolts are used on cylinder heads,
•
headlights, and transmission fill plugs.
• Set includes seven keys: M4, M5, M6, M7, M8, M9,
and M10.
No. 4609 – Ribe key set. Wt., 1 lb., 9 oz.
Ribe-style
4609
GM Seat Belt Bolt Removal Tool
Similar to
Kent-Moore
BO-47549
• Allows use of 1/2" impact wrench to remove the seat
belt retaining bolts on most GM cars and light trucks.
collar fits over the TORX® bit to center the
•
impact wrench and bit to the seat belt bolt, preventing
damage to the bit and seat belt bolt.
No. 5901 – GM seat belt bolt removal tool. Wt., 8 oz.
Outer
5901
RIBE Bit Set – 24 Piece
The bit pattern known as “RIBE” or “polydrive” is now
used on most European cars and light trucks, and is
fast becoming more common with U.S. manufacturers.
Packaged in a metal box, this is the largest collection
of RIBE bits on the market.
No. 5909 – RIBE bit set–24 piece. Wt., 8 lbs.
5909
174
GENERAL PURPOSE TOOLS
Retaining Ring Pliers
Retaining Ring, Snap Ring Pliers . . . . 176–179
Vacuum Pumps . . . . . . . . . . . . . . . . . . . . . . 179
Extractor Sets . . . . . . . . . . . . . . . . . . . . . . . 180
Torque Wrenches . . . . . . . . . . . . . . . . 180–181
Torque Angle, and Radio Tools . . . . . . 181–183
Hose Service . . . . . . . . . . . . . . . . . . . . . . . . 183
Wire Strippers, Crimpers . . . . . . . . . . . . . . . 184
Battery Service . . . . . . . . . . . . . . . . . . 184–186
Headlamp, and Mirror Tools . . . . . . . . 186–187
Gland Nut, and Misc. Tools . . . . . . . . . . . . . 187
Chisel, Punch, and Misc. Tools . . . . . . 188–189
Molding / Upholstery Tools . . . . . . . . . 190–191
Scraping Tools . . . . . . . . . . . . . . . . . . . . . . . 191
Prying Tools . . . . . . . . . . . . . . . . . . . . . 192–193
O-ring Picks . . . . . . . . . . . . . . . . . . . . . . . . . 193
Thread Chaser . . . . . . . . . . . . . . . . . . . . . . 194
Hex Key Wrenches, and Misc. . . . . . . . . . . 194
Adjustable, and Spanner Wrenches . . 196–197
Stud Remover Sets . . . . . . . . . . . . . . . . . . . 197
Driver Tools & Pullers . . . . . . . . . . . . . 198–199
Oil Filter Wrenches . . . . . . . . . . . . . . . 199–201
Strap / Chain Wrenches . . . . . . . . . . . . . . . 202
Body Tools, Seal Puller, & Stethoscope . . . 203
Holding Fixtures . . . . . . . . . . . . . . . . . . . . . 204
175
GENERAL PURPOSE TOOLS
Retaining Ring Pliers
Retaining Ring Pliers
No. 7053K
Similar to Ford
No. D79L-7000-A
15702
7123K
7125K
Here are a variety of retaining ring pliers, available
individually or in sets, to handle many applications.
No. 7053K – Internal/external retaining ring pliers kit.
Includes four 90° tips (.038" diameter), four 45° tips (.047"
diameter), and eight straight tips (.047" and .070" diameter).
Wt., 11 oz.
No. 15702 – Replacement tip kit. Contains 4 sets, 4 tips per
set. Wt., 2 oz.
No. 7123K – Convertible retaining ring pliers kit. For internal
or external rings. Contains one No. 1120 (.038" diameter)
and one No. 1340 (.070" diameter) straight tip pliers.
Wt., 15 oz.
No. 7125K – Convertible retaining ring pliers kit. For internal
or external rings. Contains one No. 1125 (.038" diameter)
and one No. 1345 (.070" diameter) 45° pliers.
Wt., 15 oz.
No. 7300 – Internal, straight tip retaining ring pliers. 16"
long. Wt., 2 lbs., 2 oz.
No. 7301 – External, straight tip retaining ring pliers. 16"
long. Wt., 2 lbs., 2 oz.
Replacement tips (pairs):
No. 209201 – For pliers Nos. 7300 and 7301. Wt., 2 oz.
No. 222029 – 45° for pliers Nos. 7300 and 7301. Wt., 2 oz.
No. 222030 – 90° for pliers Nos. 7300 and 7301. Wt., 2 oz.
7300
Internal
No. 0100
No. 0300
No. 0500
No. 7300
Convertible
No.
No.
No.
No.
No. 0200
No. 0400
No. 0600
176
1120
1125
1340
1345
External
No. 7301
How to select the correct pliers:
1. If ring number is known, locate ring number in chart
—pliers are listed in right-hand column.
2. Or, measure diameter of shaft bore and locate size in
chart —pliers are in right-hand column.
Ring
Size Range
Series No. (Ring Size No.)
5100
5101
5102
5555
5108
N5000
N5001
N5002
5008
12 to 87
12,15,25 to 66
25 to 143
93 to 143
31 to 75
150 to 350
75
354 to 650
50 to 100
50 to 78
50 to 200
106 to 200
215 to 334
350 to 400
37 to 102
37 to 56
37 to 200
106 to 175
181 to 300
306 to 625
75 to 137
75 to 100
75 to 200
143 to 200
206 to 300
315 to 400
Bore of Shaft
Dia. Range
(“Inch” equiv.)
1/8" to 7/8"
1/8" to 21/32"
1/4" to 1-7/16"
15/16" to 1-7/16"
5/16" to 3/4"
1-1/2" to 3-1/2"
3/4" 3-35/64" to 6-1/2"
1/2" to 1"
1/2" to 25/32"
1/2" to 2"
1-1/16" to 2"
2-1/8" to 3-11/32"
3-1/2" to 4"
3/8" to 1-1/32"
3/8" to 9/16"
3/8" to 1-3/4"
1-1/16" to 1-3/4"
1-13/16" to 3-1/2"
3-1/16" to 6-1/4"
3/4" to 1-3/8"
3/4" to 1"
3/4" to 2"
1-7/16" to 2"
2-1/16" to 3"
3-5/32" to 4"
Pliers No.
0200
1120, 1125
7053K, 7123K, or 7125K
1340, 1345, or 0400
0600
7301
0200
1120
7053K, 7123K, or 7125K
1340, 1345, or 0400
0600
7301
0100
1120, 1125
7053K, 7123K, or 7125K
1340, 0300
0500
7300
0100
1120, 1125
7053K, 7123K, or 7125K
1340, 1345, or 0300
0500
7300
GENERAL PURPOSE TOOLS
Retaining Ring Pliers
Retaining Ring Pliers Set
This set includes 12 of our most
popular retaining ring pliers, in sizes
for automotive applications. Tips
include straight, 45°, and 90° angles
in four different sizes (.038, .047,
.070, and .090" diameter).
•Includes a sturdy plastic organizer
box.
No. 7412K – Retaining ring pliers
set. Wt., 5 lbs.
No. 7412K includes:
Tool No. Description
1120.038" dia., straight
1125.038" dia., 45°
1131.038" dia., 90°
1320.047" dia., straight
1325.047" dia., 45°
1329.047" dia., 90°
1340.070" dia., straight
1345.070" dia., 45°
1349.070" dia., 90°
1560.090" dia., straight
1565.090" dia., 45°
1569 .090" dia., 90°
Ship.
Wt.
4 oz.
4 oz.
4 oz.
4 oz.
4 oz.
4 oz.
7 oz.
7 oz.
7 oz.
9 oz.
9 oz.
9 oz.
7412K
All items can be purchased separately.
Snap Ring Pliers Set –
Internal/External
•For internal or external snap rings;
thumbscrew permits quick
conversion.
•Made of heavy-gauge tempered
steel.
•Includes two stainless steel
handled picks.
•Contained in a blow-molded plastic
storage case.
No. 4512 – Snap ring pliers set.
Wt., 4 lbs., 3 oz.
Convertible Retaining Ring
Pliers Set
The convertible pliers in this set
can be used on automotive snap
rings, in either internal or external
applications.
•Includes a sturdy plastic organizer
box.
No. 7888 – Convertible retaining ring
pliers set. Wt., 2 lbs., 2 oz.
No. 4512 includes:
Tool No.
Description
4512-1.090" tip, straight pliers
4512-2.090" tip, 90° pliers
4512-3.070" tip, straight pliers
4512-4.070" tip, 90° pliers
4512-5.047" tip, straight pliers
4512-6.047" tip, 90° pliers
4512-7.038" tip, straight pliers
4512-8.038" tip, 90° pliers
4512-9 straight tip pick
4512-10 90° tip pick
No. 7888 includes:
Tool No. Description
1120.038" dia., straight
1125.038" dia., 45°
1320.047" dia., straight
1325.047" dia., 45°
1340.070" dia., straight
1345.070" dia., 45°
4512
Ship.
Wt.
4 oz.
4 oz.
4 oz.
4 oz.
7 oz.
7 oz.
7888
7888
177
GENERAL PURPOSE TOOLS
Snap Ring Pliers
Mini Snap Ring Pliers Set (4 piece)
4514
•Small-size pliers for work in tight areas. Service S-ring
and R-ring clips, internal or external, straight or angled.
Ruggedly built of heat-treated chrome molybdenum steel.
•Set includes two internal snap ring pliers (one straight,
one 45°) and two external snap right pliers (one straight,
one 45°).
•All pliers have .038" (1.0mm) diameter tips.
•Overall length 3"; handle length 2".
No. 4514 – Mini snap ring pliers set. Wt., 6 oz.
Heavy-Duty Snap Ring Pliers Set (2 piece)
4513
• Heat treated steel “circlip” pliers for large equipment repair Replaceable tips and spring ratchet locking mechanism to securely hold against snap ring tension.
•Internal pliers’ capacity 3-1/16"
No. 4513 includes:
to 6-1/4" (78 mm to 159 mm)
Tool No.
Description
snap rings.
4513-1 Internal snap ring pliers
•External pliers’ capacity 3-1/2"
4513-2 External snap ring pliers
to 6-1/2" (89 mm to 165 mm)
4513-3 (2) .12" (3 mm) straight tip
snap rings.
4513-4 (2) .12" (3 mm) 45° tips
•Blow-molded storage case
4513-5 (2) .12" (3 mm) 90° tips
includes extra sets of 4513-6 4 tip retaining screws
replaceable tips.
•Overall length 16"; handle length 12-1/2".
No. 4513 – Heavy-duty snap ring pliers set. Wt., 7 lbs., 3 oz.
Retaining Ring Pliers
The “squeeze-lock” ratchet action of this tool locks retaining
rings in position, making removal and installation easy. It
features cushioned handles to ensure a secure grip.
•Will handle rings 3/16" thick and up to 4" in diameter.
•Pliers is 12" long.
No. 7295 – Retaining ring pliers. Wt., 1 lb., 2 oz.
No. 211051 – Pair of replacement tips. Wt., 2 oz.
7295
Retaining Ring Pliers
7313
This tool removes the external retaining rings used
in transmissions, differentials and other automotive
components.
•Maximum spread is 1-1/16".
No. 7313 – Retaining ring pliers, 7-3/4" long. Wt., 8 oz.
Horseshoe Lock Ring Pliers
714
178
This ruggedly built pliers is designed to spread and
remove horseshoe lock rings used on hydraulic brakes,
differentials, transmissions, and CV joints.
•Handles are 8" long.
No. 714 – Horseshoe lock ring pliers. Wt., 8 oz.
GENERAL PURPOSE TOOLS
Ring Pliers, Vacuum Pumps
Retaining Ring Pliers
An ideal tool for any transmission shop, this 13" long pliers
with a maximum spread of 2.5" features replaceable tips
and a spring-return handle.
No. 7410 – Retaining ring pliers with replaceable tips.
Wt., 1 lb., 5 oz.
No. 214903 – Set of replacement tips. Wt., 2 oz.
7410
Fluid Evacuation / Brake Bleeding Tools
•Use to bleed brake systems and remove a variety of fluid
from vehicles, such as antifreeze, oil, transmission fluid,
gear lube, etc.
•Quick connect locking hose adapters and ball-style on/off
valve on hose prevent fluid leakage.
•Equipped with a relief valve to prevent over-pressurizing
the tank.
No. 8100 – Operates by shop air or a hand pump; shipped
complete with a brake bleeding hose, fluid evacuation hose,
and two suction hoses (6 mm and 7 mm); 10-liter capacity
tank. Wt., 10 lbs.
No. 8101 – Operates with shop air; shipped with a brake
bleeding hose and fluid evacuation hose; 6-liter capacity tank.
Wt., 10 lbs., 13 oz.
8101
8100
Deluxe Metal Vacuum Pump
With this multipurpose pump, vacuum testing and brake
bleeding are one-person operations. Made of die cast
metal, the repairable pump will develop and hold about
25" of mercury vacuum. It comes with all the components
needed to help speed you through most brake jobs.
•Includes an easy-to-read gauge (inch and mm
graduations), reservoir jar, transfer and storage lids,
rubber cup adapter, brake-bleeding adapters, tubing,
and carrying case.
No. 7559 – Deluxe metal vacuum pump.
Wt., 3 lbs., 12 oz.
7559
Vacuum / Pressure Pump Kit
•Hand pump may be set to create vacuum or pressure.
•Gauge on pump reads 0–30 in. Hg (0 to -1 BAR)
vacuum; 0–60 psi (0–4 BAR) pressure.
•Includes an assortment of fittings and hoses to adapt
to most components that need to be tested.
•Includes brake fluid reservoir for bleeding brake
systems.
No. 4752 – Vacuum/pressure pump kit.
Wt., 4 lbs., 4 oz.
4752
179
GENERAL PURPOSE TOOLS
Stud, Screw Extractor & Torque Wrenches
Combination Stud Extractor and Drill Bit Set
•Removes bolts and screws up to 5/8" diameter.
•Set contains:
– Five left-handed stud extractors: 5/64", 7/64", 5/32",
1/4", and 19/64".
– Five left-handed cobalt drill bits: 5/64", 7/64", 5/32",
1/4", and 19/64".
No. 4545 – Combination stud extractor and drill bit set.
Wt., 13 oz.
4545
Fingertip Ratchet Bit and
Socket Kit (29 piece)
•Two fingertip ratchets (three-positions: forward, lock,
reverse). One bit driver; one socket driver with quick
release.
•13-piece, 1/4" drive sockets. SAE: 1/4", 9/32", 5/16",
11/32", 3/8", 7/16". Metric: 6 mm, 7 mm, 8 mm, 9 mm,
10 mm, 12 mm, 13 mm.
•14-piece, 4.5, 6.5 slotted bits, #1 and #2 Phillips bits
TORX: T10, T15, T20, T25, T27, T30; Tamper resistant
T10, T15, T20, T25.
5910
No. 5910 – Fingertip ratchet bit and socket kit (29 piece).
Wt., 1 lb.
Screw Extractor Set
•Removes broken studs and bolts.
•Includes ten guide bushings, five drill bits and five screw
extractors with extractor nuts.
•Drill bits are left handed to help removal.
No. 4651 – Screw extractor set. Wt., 1 lbs., 7 oz.
4651
AccutorqTM Clikker Torque Wrenches
7379
7378
7377
7375
OTC
Square
No. Torque Range
Graduations Drive Length
7375
7377
7378
7379
150–750 in. lbs. (17–85 N•m)
30–150 ft. lbs. (41–203 N•m)
50–250 ft. lbs. (68–339 N•m)
100–600 ft. lbs. (136–813 N•m)
180
10 in. lbs.
2 ft. lbs.
2 ft. lbs.
10 ft. lbs.
3/8"
1/2"
1/2"
3/4"
15-1/8"
17-3/4"
19-3/8"
42-1/4"
Wt.
(Lbs.)
2.8
4.2
4.2
14
These precision torque wrenches make a loud click when
you’ve reached the torque setting. They feature ratcheting heads, all-metal construction, permanently roll-marked
scales, and soft-grip rubber handles that enable you to
firmly grasp the wrench for right- or left-hand torquing.
•Includes molded plastic case.
• One-year warranty.
No. 7375 – 150–750 in. lbs. Accutorq Clikker torque
wrench. Wt., 2 lbs., 8 oz.
No. 7377 – 30–150 ft. lbs. Accutorq Clikker torque
wrench. Wt., 4 lbs., 3 oz.
No. 7378 – 50–250 ft. lbs. Accutorq Clikker torque
wrench. Wt., 4 lbs., 3 oz.
No. 7379 – 100–600 ft. lbs. Accutorq Clikker torque
wrench. Wt., 14 lbs.
GENERAL PURPOSE TOOLS
Torque Angle
Torque Multipliers
These 4:1 ratio torque multiplers provide the power to
tighten threaded fasteners in a number of truck and tractor
repair operations.
No. 5073 – 1,000 lb. capacity torque multiplier. Has 1/2"
square drive and 3/4" square drive output. Includes 14"
extension handle. Wt., 7 lbs.
No. 5074 – 2,000 lb. capacity torque multipler. Has 3/4"
square drive and 1" square drive output. Includes 18"
extension handle. Wt., 14 lbs.
5074
5073
Accutorq™ Dial Torque Wrench
This torque wrench features a large, easy-to-read dial scale
with memory needle, and has chrome-plated steel surrounding
the bezel to protect the scale, lens, and needle.
•Meets all federal specifications.
7380
•Includes molded plastic case.
•One-year warranty.
OTC
No.
Torque Range
Graduations
No. 7380 – Accutorq™ dial torque wrench. Wt.,1 lb., 12 oz.
7380
0–150 in. lbs. (0–17 N•m) 3 in. lbs.
Square
Drive
Length
3/8"
10"
Wt.
(Lbs.)
1.7
Torque Angle Meter
This meter simply connects to any standard 1/2” socket extention
and measures angle rotation, electronically! Clip unit to socket
extension and enter desired angle. No support arm to connect between
each fastener, fast and accurate to use. Unit will beep and flash when
desired angle is reached. 0-199 degree capability, +/- 1% accuracy.
No. 3559 – Torque angle meter. Wt., 11 oz.
3559
Torque Angle Gauge
Many manufacturers specify a torque angle procedure for
tightening fasteners and head bolts because it helps ensure
more accurate tightening. This torque angle gauge, featuring
an easy-to-read gauge, will provide a precise reading.
•Accommodates a 1/2" drive torque wrench.
No. 7415 – Torque angle gauge. Wt., 2 oz.
7415
Torque Angle Gauge
•Required when servicing many late model engines that
use torque-to-yield fasteners. Measures angle of rotation
after pre-torque in torque-angle applications.
•The 360° scale is marked in 2° increments and intervals of
10° and 30°; easily zeroed for next application by turning
the tool housing.
•Has 1/2" male and female square drives.
No. 4554 – Torque angle gauge. Wt., 6 oz.
4554
Magnetic Parts Tray
• Rectangular, stainless steel tray is 9-1/2" x 5-1/2" and 1-1/4" deep. Holds tools and small metal parts, so they
don’t get lost or misplaced during repair work.
• Two heavy-duty magnets on bottom of tray, with nonmarring contact pads, securely hold tray to metal objects
such as a tool box, air cleaner cover, frame rail, fender, etc.
No. 4490 – Magnetic parts tray. Wt., 1 lb., 11 oz.
4490
181
GENERAL PURPOSE TOOLS
Radio Service Tools
Air Bag Release Tool Kit
•Use to remove the air bag module from the steering wheel.
•Work on many GM, Ford and Mercedes Benz vehicles.
Applications:
Ford 2000-2004 Taurus/Sable, 1999-2003 Windstar Van.
GM 1999-2005 Chevrolet Impala, Lumina, Monte Carlo, Venture, Pontiac Bonneville,
Grand Prix, Montana, Buick LeSabre, Century, Regal, Olds Intrigue, Cadillac El
Dorado, Deville, STS, SLS.
Mercedes Benz Models 107,123, 124, 126, 129, 140, 163, 164, 170, 201, 202, 203,
208, 209, 210, 211, 215, 219, 220, 221 and 463.
5945
No. 5945 – Air bag release tool kit. Wt., 2 lbs.
Deluxe Radio and Antenna Service Kit
4711
•Eleven-piece kit in molded case.
•Universal antenna wrench.
•Ford radio removal tool.
•Deep sockets to remove and install the tamper-proof radio
nuts from many GM, Chrysler, and other aftermarket radios.
•Antenna nut sockets cover most import and domestic
antenna nuts.
No. 4711 – Radio and antenna kit. Wt., 1 lbs., 13 oz.
Euro Radio Removal Tool Kit
4712
•Includes the popular tools needed to remove the radio
from the dash on the following European vehicles: BMW,
VW, Audi, and Mercedes-Benz.
•Easily removes the radio without damaging the radio
or the dash panel.
No. 4712 – Euro radio removal tool kit. Wt., 13 oz.
Deluxe European Radio Tool Set
• 18-piece set of tools used to remove radios on most
European vehicles sold in the U.S. and Europe.
• Quickly and easily removes the radio from the dash
without damage to the radio or dash.
Replacement Parts
4715
Part No. Description Application
4715-1 Removal Keys (4 pieces) Audi, Becker, Mercedes-Benz, VW
4715-2 Removal Keys (2 pieces) Becker, Mercedes-Benz, Porsche
4715-3 Removal Keys (2 pieces) VW
4715-4 Removal Keys (2 pieces) Skoda
4715-5 Removal Keys (2 pieces) Becker
4715-6 Pentagon Wrench BMW
4715-7 Bent U-hook (2 pieces) Blaupunkt
4715-8 U-hook (2 pieces) Audi, Blaupunkt, Ford, Grundig, VW
4715-9 Allen Hex Wrench BMW, Opel
No. 4715 – Deluxe European radio tool set. Wt., 1 lbs., 3 oz.
Similar to
SA9148B
7827
182
Saturn Window Glass Socket
This specially designed socket enables you to easily remove
the tricky fasteners that Saturn uses to hold window glass
to the regulator in its car doors. Our tool won’t cause the
damage that often results from makeshift methods.
•For use on 1991 to current models.
•Accommodates a 3/8" drive ratchet and extension.
No. 7827 – Saturn window glass socket. Wt., 3 oz.
GENERAL PURPOSE TOOLS
Radio & Hose Service
Mercedes-Benz Dashboard Service Tool Kit
• 8-piece tool kit contains:
• (2) removal tools for ignition lock on model W126.
• (2) removal tools for ignition locks on models W124 & W201.
6711
• (2) removal hooks for instrument cluster on models W107,
W116, W123, W124, W126, W140, and W201.
•(2) radio removal tools on models W129, W140, W202, and W210.
• Covers virtually all Mercedes-Benz models since 1992.
No. 6711 – Mercedes-Benz dashboard service tool kit. Wt., 10 oz.
Ford Radio Removal Tool Kit
These dual-purpose tools release the retaining clips of a
radio faceplate so you can pull the radio from the instrument
panel. For use on 1987 to current Mustang; 1988 and newer
Tempo/Topaz; 1989 to current Lincoln Continental; 1990 to
current Taurus/Sable, Ranger/Bronco II, Probe, Lincoln Town
Car, Mark VII, Crown Victoria/ Grand Marquis, Thunderbird/
Cougar, F-series pickups and E-series vans; 1991 to current
Explorer; 1995 to 2003 Windstar.
No. 7575 – Ford radio removal tool kit. Wt., 2 oz.
7575
Similar to Ford
No. T87P-19061-A, 415-001
Hose Pinch-off Pliers Set (3 piece)
•Shuts off flow through vacuum, fuel, and coolant lines, etc.
•Cocking ratchet mechanism holds pivoting jaws tightly in place.
Heavy-duty swivel jaws pivot to ensure parallel pinching.
•These three tools are available separately:
No. 4510-8 – 8" tool for small hoses and tight areas
No. 4510-10 – 10" tool for radiator and vacuum lines
No. 4510-12 – 12" tool for radiator and vacuum lines
No. 4510 – Set of three pinch-off pliers. Wt., 2 lbs., 11 oz.
4510
Hose Cutter – “Guillotine”
•Hooks and cuts plastic lines and rubber hoses from 1/8" to
1" diameter. Simply hook hose in V-shaped end, and
squeeze handle to cut. Compound mechanical leverage
provides power. Spring-loaded blade returns to open
position after use, so blade is not exposed.
•Linear design hook reaches and cuts hoses in tight areas.
•Replacement steel cutter blade No. 4511-1 is available.
No. 4511 – Hose cutter tool. Wt., 8 oz.
No. 4511-1 – Replacement blades. Wt., 2 oz..
Straight-Blade Hose Cutter
•Cuts rubber hoses ranging from 1/4" to 1-1/2".
•Simply place hose in tool and squeeze handle to cut.
•Replacement steel cutter blade No. 4509-1 is available.
No. 4509 – Straight blade hose cutter. Wt., 5 oz.
Rubber Hose Pinch-off Pliers
These pliers keep rubber fuel and water lines clamped tightly
when you’re servicing engine components. The grip pads provide a damage-free method of shutting off flow without having
to drain the hoses. Pivoting jaws and locking ratchet provide
a tight grip in just about any position.
No. 7655 – Hose pinch-off pliers. Wt., 13 oz.
4511
4509
7655
183
GENERAL PURPOSE TOOLS
Pliers, Crimpers & Puller
Angle-Tip Relay Pliers
4493
•Designed to remove and install relays, which are usually
located in confined, hard-to-reach areas.
•Specially coated tips offer a solid grip on the relay.
No. 4493 – Angle-tip relay pliers. Wt., 10 oz.
Ratcheting Terminal Crimper
4497
•Heavy-gauge steel crimping tool designed for insulated
wire terminals.
•Ratcheting action crimps terminal to correct tightness on
the wire, making crimping fast and easy.
•For wire sizes: AWG 22–18 (0.6 mm–1.0 mm) red terminal;
AWG 16–14 (1.3 mm –1.6 mm) blue terminal; AWG 12–10
(2.0 mm–2.6 mm) yellow terminal.
•Insulated handles with compound mechanical leverage for
power.
No. 4497 – Ratcheting terminal crimper. Wt., 1 lb., 3 oz.
7-in-1 Wire Stripper and Crimper
•Strips insulation off electrical wires ranging from 10 AWG—
22 AWG (0.6mm—2.6mm) in diameter. Pliers on tip of jaw
for looping or grabbing wire in tight places.
•Heat-treated steel jaws cut solid or multi-strand wire.
•Screw cutter shears screws clean, with no thread clean-up required. Works on machine screw sizes 4-40, 5-40, 6-32, 8-32, 10-24, and 10-32.
4498
•Crimps insulated and non-insulated wire terminals, 7mm—
8mm spark plug wire connectors.
No. 4498 – 7-in-1 wire stripper and crimper. Wt., 8 oz.
Wire Stripper and Cutter
•Only 6" in length. Clean size separations and
markings allow ease of use in tight areas.
•Strips insulation off of electrical wires ranging from
10 AWG—22 AWG (0.6mm—2.6mm) in diameter. Heat-treated steel construction with durable grips.
4499
•Spring-loaded jaws stay open for ease of use, and lock for storage; gripping area at tip of jaws for
working in tight areas; wire cutter at base of jaws.
No. 4499 – Wire stripper and cutter. Wt., 5 oz.
Battery Terminal Puller
4611
184
•Designed to remove the battery cable clamp from the post without causing damage to the battery.
•Spring-loaded sharp jaws get under the clamp for a secure grip.
No. 4611 – Battery terminal puller. Wt., 14 oz.
GENERAL PURPOSE TOOLS
Battery Service
3-Way Battery Post Cleaner
•Steel blades quickly clean top-post battery terminals
and cable clamps; cleaners are marked “positive” and “negative.”
•Ream is tapered to clean both positive and negative
battery cable clamps.
No. 4612 – 3-Way battery post cleaner. Wt., 6 oz.
Battery Pliers
•Serrated jaws firmly grip the battery terminal nut or bolt.
•Offset handles allow access in hard-to-reach areas.
•Works on both top-post and side-post battery
terminals.
No. 4613 – Battery pliers. Wt., 10 oz.
4612
4613
Side Terminal Battery Wrench
•Designed for use on GM side-terminal batteries, or any 5/16" hex head battery bolt.
•5/16", 6 point, box end, 5-1/2" long, ratcheting wrench; insulated handle.
No. 4614 – Side-terminal battery wrench. Wt., 5 oz.
4614
Long-Side Terminal Battery Wrench
• Designed for use on GM side-terminal batteries, or any
5/16" hex head battery bolt.
• Long handle allows access to hard-to-reach battery
terminal bolts.
• 5/16", 6 point, box end, 10" long, ratcheting wrench;
insulated handle.
No. 4615 – Long-side terminal battery wrench. Wt., 8 oz.
4615
Battery Terminal Wrench – 10mm
•Designed for use on 10 mm battery terminal bolts found on many import and domestic vehicles.
•10 mm, 12 pt., box-end ratcheting wrench; 5-1/2" long with insulated handle.
No. 4616 – Battery terminal wrench - 10 mm. Wt., 3 oz.
4616
Side Terminal Battery Brush
•Designed to clean corrosion from side post batteries.
•One brush used to clean battery terminals; other brush used to clean battery cable ends.
•Plastic handle resists battery acid.
No. 4617 – Side terminal battery brush. Wt., 3 oz.
4617
185
GENERAL PURPOSE TOOLS
Battery Service
Battery Brush
4618
•Cleans dirt and corrosion from positive and negative
battery posts and cable clamps.
•Plastic case resists battery acid and most cleaning
solvents.
No. 4618 – Battery brush. Wt., 3 oz.
Battery Carrier
4620
• Use to lift and install most top post and side terminal
batteries.
• Designed to transfer lifting force to a secure hold on the
battery; teeth on jaws offer a secure grip.
• Vinyl strap resists battery acid and will not conduct
electricity.
No. 4620 – Battery carrier. Wt., 14 oz.
Professional Battery Hydrometer
4619
• Displays a battery’s specific gravity on an easy-to-read
float; scale ranges from 1.100 to 1.300.
• Thermometer indicates what must be added or
subtracted from the float reading to arrive at an
accurate specific gravity reading for each battery cell.
• Flexible tip offers easy access to the battery cells while
the battery is still in the vehicle.
No. 4619 – Professional battery hydrometer. Wt., 6 oz.
Two-Liter Battery Filler
• Replenish battery water the easy way! The fill nozzle
on this container has an automatic shut-off that prevents overfilling; the handle on the side of the container makes the job a snap. Container holds up to two liters of distilled water.
No. 4621 – Two-liter battery filler. Wt., 1 lb.
4621
Battery Cable Cutter
4622
• Designed to cut copper battery cable and aluminum
electrical cable. IMPORTANT: Do not cut steel cable;
damage to blades will occur.
• Precision-ground cutting blades provide a clean, square cut.
• 7" long handle gives extra leverage when cutting thick cable.
No. 4622 – Battery cable cutter. Wt., 1 lb. 2 oz.
Ford Headlamp Alignment Tool
186
4689
•Use to adjust aerodynamic headlamps with rear mounted
adjuster on Fords.
•4 mm hex with one-way roller clutch for precise adjustments.
•Long, ratcheting handle for easy access.
No. 4689 – Ford headlamp alignment tool. Wt., 7 oz.
GENERAL PURPOSE TOOLS
Gland Nut, Mirror & Door Tools
Ford Mirror Removal Tool
Save shop labor time and cost by allowing mirror to be
removed without damaging or removing the mirror assembly.
Works on these outside door mirrors:
• 1997–2002 Windstar
• 1998–2004 Crown Vic, Grand Marq, Marauder, Taurus,
Sable, Mustang, Town Car
• 1999–2004 Ranger, Excursion, Super Crew (F-250–
F-550), F-650, F-750
• 2001–2004 Escape
• 2002–2004 Thunderbird
• 1996–2004 Explorer
• 1997–2004 Mountaineer
• 1998–2004 Expedition, Navigator, F-150
• 1999–2004 E-Series van
• 2000–2004 LS
• 2001–2004 Explorer Sport, Explorer Sport Trac
• 2003–2004 Aviator
• 1999–2004 Dual arm mirror used on Excursion, Super
Crew (F-250–F-550), F-650, F-750
• Also works on 1999 and newer Ford interior / rearview
mirrors that have the detachable (screwless) mount.
No. 8200 – Ford mirror removal tool. Wt., 4 oz.
8200
Gland Nut Wrench
This wrench is fully adjustable to fit hydraulic cylinders on
vehicles having gland nuts from 1" to 3-3/4" in diameter. It
also reverses to work on either 1/4" or 7/32" pinholes.
•Accommodates a 1/2" drive ratchet.
No. 7463 – Gland nut wrench. Wt., 10 oz.
No. 215128 – Replacement pin. Wt., 1 oz.
7463
Adjustable Gland Nut Wrench
Here’s a wrench designed to fit hydraulic cylinders on most
farm and construction equipment. It fits gland nuts from 2" to
6" diameter pin to pin. And it’s reversible to fit 1/4" and 5/16"
diameter pinholes.
•Accommodates a 3/4" drive ratchet or breaker bar.
No. 1266 – Adjustable gland nut wrench. Wt., 2 lbs., 3 oz.
No. 204928 – Replacement pin. Wt., 1 oz.
1266
Euro Door Handle Kit
•This kit contains the tools needed to service most door
hinges and door handles on Audi, Mercedes-Benz,
Porsche, and Volkswagen vehicles.
•Kit includes: A ratchet wrench with three 12-point bits
(4 mm, 8 mm, 10 mm), one T40 and one T45 TORX® bit; a T30 TORX® long handled driver; and a T20 TORX®
T-handle driver.
•T30 driver, 14" long; T20 driver, 9-1/2" long; hex
ratchet, 9-1/2" long.
No. 6785 – Euro door handle kit. Wt., 15 oz.
6785
187
GENERAL PURPOSE TOOLS
Punch & Misc. Tools
Spot Weld Cutter Set
•Use with electric drill or air drill to cut 5/16" and 3/8"
spot welds.
•Cutter bits have cutting teeth on each end.
•Replacement kit No. 4485-1 consists of (3) 5/16" cutter
bits; (3) 3/8" cutter bits; and (4) centering tips.
No. 4485 – Spot weld cutter set. Wt., 5 oz.
4485
Exhaust Hanger Pliers
7677
Many cars and trucks have rubber blocks supporting their
exhaust system hanger brackets. These pliers will enable
you to quickly and easily remove those push-through
brackets from their hangers. These pliers feature a twoposition slip joint for use on many sizes of hanger blocks.
No. 7677 – Exhaust hanger pliers. Wt., 1 lb., 5 oz.
Universal C-Frame Nut Splitter
•Forged and heat-treated frame with offset handle works
where ordinary nut splitters may fail. Smooth action
cracks nuts without damaging bolt threads.
•Chisel rotates to line up parallel to bolt. Splits non-heat treated nuts of 7/16" (11 mm) through 3/4" (19 mm)
diameter. Tool is 6-3/4" in length.
No. 4576 – Universal C-frame nut splitter. Wt., 1 lb., 8 oz.
4576
Punch and Chisel Set (16 piece)
•Durable set of heat-treated chrome vanadium steel punches and chisels. Storage tray included.
Contents of set, available separately:
3 ­­– Cold chisels (with gauge): 3/8" x 5-1/2"; 1/2" x 6";
5/8" x 6-1/2"
2 ­­– Center punches: 1/8" x 5"; 3/16" x 6"
5 ­­– Pin punches: 3/32" x 4-1/4"; 1/8" x 4-3/4"; 5/32" x 5";
3/16" x 5-1/4"; 1/4" x 5-3/4"
5 ­­– Taper punches: 3/32" x 5-1/4"; 1/8" x 5-3/4"; 5/32" x 6";
3/16" x 6-1/4"; 1/4" x 6-3/4"
1 – Chisel gauge
No. 4600 – Punch and chisel set (16 piece).
Wt., 2 lbs., 11 oz.
4600
Brass Punch Set (2 piece)
4602
188
•Two large, brass non-sparking punches. Ideal for use near
precision parts or in locations where sparks from ferrous
metal could be hazardous.
•Includes an 8" punch (5/8" hex, tapered to 3/8") and 10"
straight punch (3/4" dia., chamfered at both ends).
No. 4602 – Brass punch set. Wt., 2 lbs., 3 oz.
GENERAL PURPOSE TOOLS
Chisel & Punch Sets, Steering Wheel Holder
Steering Wheel Holder & Pedal Depressor Kit
• This kit has two applications: 1) holds steering wheel in
position for alignment adjustments, and 2) depresses
brake pedal for various brake checks, including brake lamp
operation.
• Rod easily slides in actuator for fast, easy installation
of tool on brake pedal or steering wheel. Simply hand
squeeze the actuator to accomplish fine adjustments.
• Kit includes: actuator assembly; extension rod for
actuator (use when depressing brake pedal); hook
assembly (hooks on steering wheel when depressing
brake pedal or holding steering wheel); and flat pad
(rests on front seal when holding steering wheel).
No. 4546 – Steering wheel holder and pedal depressor kit.
Wt., 5 lbs., 2 oz.
4546-1 – Handle and Rod. Wt., 2 lbs.
4546-2 – Steering wheel and pedal holder.
Wt., 2 lbs., 3 oz.
4546
Interchangeable Punch and Chisel Set
•Handle allows easy grip and protects hand from being hit
by hammer.
•12 punches and chisels:
1 cape chisel: 1/4" wide blade
5 flat chisels: 1/2", 5/8", 3/4", 7/8", and 1" wide blades
2 taper punches: 1/8" and 1/4" diameter
2 pin punches: 3/16" and 1/4" diameter
2 center punches: 1/8" and 3/16" diameter
•Double-locking ball detent holds punch or chisel securely
in the driver handle.
No. 4605 – Interchangeable punch and chisel set.
Wt., 4 lbs., 7 oz.
4605
Interchangeable
Autobody Forming and Punch Kit
Includes:
4605-1 – Drive handle
4756-1 – Small curve tool
4756-2 – Cross curve tool
4756-3 – Rounded ball-peen tool
4756-4 – One-sided flat blade tool
4756-5 – Curve blade tool
4756-6 – Pointed ball-peen tool
4756-7 – Angle face tool
4756-8 – Flat blade tool
4756-9 – Square face tool
4756-10 – Angle groove tool
4756-11 – Round face tool
No. 4756 – Interchangeable autobody forming and punch
kit. Wt., 4 lbs., 13 oz.
4756
189
GENERAL PURPOSE TOOLS
Drivers & Misc. Tools
Impact Drivers
•Loosens hard-to-turn screws, bolts or nuts.
•Handle design prevents possibility of hitting hand with
hammer when striking impact driver.
•Bit holder has 3/8" drive (No. 4608), 1/2" (No. 4607) drive,
and 5/16" hex for Phillips and flat screwdriver bits.
•Includes eight screwdriver bits:
No. 2 Phillips bit, 1-3/8" long with 5/16" hex
No. 2 Phillips bit, 3-1/8" long with 5/16" hex
No. 3 Phillips bit, 1-3/8" long with 5/16" hex
No. 3 Phillips bit, 3-1/8" long with 5/16" hex
5/16" wide x 1-3/8" long with 5/16" hex slotted bit
5/16" wide x 3-1/8" long with 5/16" hex slotted bit
3/8" wide x 1-3/8" long with 5/16" hex slotted bit
3/8" wide x 3-1/8" long with 5/16" hex slotted bit
No. 4607 – 1/2" impact driver. Wt., 2 lbs., 4 oz.
No. 4608 – 3/8" impact driver. Wt., 2 lbs., 4 oz.
4608
4606
Brass Hammer and Punch Set
•Brass-head hammer and punches are ideal to use where
sparks from ferrous metals would be hazardous, or where
precision metal parts could be damaged by steel tools.
•Hammer head weighs 24 oz.; brass drift punch is
10" x 3/4" diameter; brass tapered punch is 8" x 5/8" hex
tapered to 3/8" diameter point.
No. 4606 – Brass hammer and punch set.
Wt., 4 lbs., 2 oz.
Trim Fastener and Molding Removal Set
•Set includes five different sizes and styles of tools that
allow easy removal of trim fasteners, moldings, and wheel
hubs.
•Tools are made of plastic to prevent damage to trim,
moldings, alloy wheels, or vehicle paint.
•Can be used on trim fasteners and moldings inside, or
outside, the vehicle.
No. 4489 – Trim fastener and molding removal set. Wt., 13 oz.
4489
Mercedes-Benz Molding Removal Kit
•3-piece kit designed to save time for the shop when
servicing M-B vehicle interiors.
•Works on/in virtually all Mercedes-Benz.
•No. 6789 along with the No. 4489 set cover most vehicle
interiors on the road today.
6789
190
No. 6789 – Mercedes-Benz molding removal kit. Wt., 12 oz.
GENERAL PURPOSE TOOLS
Misc. Tools & Scrapers
5-Piece E-Clip Tool Set
•Dual operation tool: one end of tool releases e-clip; other
end of tool installs e-clip.
•Tools fit four sizes of e-clips: 6 mm, 7 mm, 8 mm, and
9 mm.
•Each tool easily locks into handle provided.
No. 4492 – 5-piece E-clip tool set. Wt., 10 oz.
4492
Assembled tool
Door Panel & Upholstery Tool Set
Heavy-duty door panel and upholstery tools:
No. 4549-1 – removes window and door handle clips, and
upholstery tucking.
No. 4549-2 – V-notched door panel clip removal tool.
No. 4549-3 – U-notched door panel clip removal tool.
No. 4549 – Door panel and upholstery tool set – 3-piece.
Wt., 1 lb.
4549
Small Door Panel & Upholstery Tool Set
Heavy-duty tools with stainless steel blades used for
removing small door panels and upholstery clips:
No. 4551-1 – U-notched tool
No. 4551-2 – V-notched tool
4551
No. 4551 – Small door panel and upholstery tool set.
Wt., 8 oz.
Putty Knife Set
Heavy-duty stainless steel, precision ground, and
polished. Blades taper at tip to provide great flexibility and
blade action. Ergonomic, two-component plastic handles
provide a non-slip grip.
•Packaged in a storage tray. Includes three flexible blade
knives: 1-1/4", 2", and 3".
No. 4552-1 – Large putty knife.
No. 4552-2 – Medium putty knife.
No. 4552-3 –Small putty knife.
4552
No. 4552 – Putty knife set. Wt., 13 oz.
Scraper Set
Scrapers feature polished, heat-treated, stiff, stainless steel
blades. Handles are ergonomic two-component plastic and
feature a non-slip grip and steel bolstered end.
•Packaged in a storage tray. Includes: 1-1/4" straight
blade, 1-1/4" bent blade, and 2" straight blade.
No. 4550-1 – Medium scraper.
No. 4550-2 – Small scraper.
No. 4550-3 – Angled scraper.
4550
No. 4550 – Scraper set. Wt., 1 lb., 2 oz.
191
GENERAL PURPOSE TOOLS
Prying Tools
Handled Pry Bars
Finally, a heavy-duty pry bar made of tempered square
steel that you can hit without damaging the handle.
•Black chrome striking cap allows hitting the bar without
damage to the handle.
•Ergonomic handle – dual durometer composite handle for
user comfort; reduces hand fatigue.
•Polished tip with black oxide finish.
•Long-life finish resists rust and wear during use.
•OTC Marathon Lifetime Warranty.
8203
8206
8245
8245S
No. 8203 – 3-piece handled pry bar
set in gray molded tray. Includes 12", 18", and 24" sizes.
Wt., 3 lbs.
No. 8206 – 6-piece handled pry bar set in gray molded tray.
Includes 8", 12", 18", 24", 32" and 36" sizes.
Wt., 6 lbs., 10 oz.
No. 8208 – 8" handled pry bar. Wt., 8 oz.
No. 8212 – 12" handled pry bar. Wt., 10 oz.
No. 8218 – 18" handled pry bar. Wt., 1 lb.
No. 8224 – 24" handled pry bar. Wt., 1 lbs., 4 oz.
No. 8232 – 32" handled pry bar. Wt., 1 lbs., 12 oz.
No. 8236 – 36" handled pry bar. Wt., 2 lbs., 2 oz.
No. 8245 – 45" handled pry bar. Wt., 5 lbs.
No. 8245S – 45" handled pry bar with straight blade.
Wt., 5 lbs.
Jimmy Bars
We’ve forged these bars from chrome alloy steel, then heattreated them to resist bending and breaking.
No. 7166 – 5/8" diameter, 18" long. Wt., 1 lb., 8 oz.
No. 7167 – 3/4" diameter, 24" long. Wt., 2 lbs., 10 oz.
No. 7168 – 7/8" diameter, 30" long. Wt., 4 lbs., 7 oz.
No. 7420 – 7/8" diameter, 46" long. Wt., 8 lbs.
No. 7421 – 1" diameter, 54" long. Wt., 11 lbs., 3 oz.
192
GENERAL PURPOSE TOOLS
Pry Bars, Picks and Magnets
Rolling Head Pry Bars
You’ll have a lot of leverage using one of these rolling
head pry bars. The long, tapered body will also serve as
an aligning drift.
No. 7162 – Pry bar; 6" long. Wt., 3 oz.
No. 7163 – Pry bar; 12" long. Wt., 10 oz.
No. 7164 – Pry bar; 16" long. Wt., 1 lb., 8 oz.
No. 7165 – Pry bar; 18" long. Wt., 2 lbs., 7 oz.
Pry Pac
Three pry bars in one economical pack. You get 12" and 18"
rolling head pry bars and a 24" jimmy bar.
•Heat-treated chrome alloy steel.
No. 7171 – Pry pac. Wt., 6 lbs., 13 oz.
7171
Mini Pick and Hook Set – 4-Piece
•Sturdy stainless steel points and shafts designed for
marking, removing o-rings, accessing snap rings, and
performing other tasks. Assorted angle tips allow you to
reach awkward locations.
•Knurled shaft design enhances finger control for delicate
jobs.
No. 4515 – Mini pick and hook set. Wt., 5 oz.
O-Ring / Oil Seal Pick
Here’s an extremely handy tool that makes quick work of oil
seal and o-ring removal and installation.
No. 7312 – O-ring/oil seal pick. Wt., 2 oz.
4515
Similar to Ford
No. 100-010
7312
O-Ring / Oil Seal Pick Set
7103
Fishing a stubborn o-ring or oil seal out of its seat is easy if
you have this pair of picks in your toolbox.
No. 7103 – O-ring/oil seal pick set. Wt., 7 oz.
Mirror and Magnet Set
•Handles telescope from 6-1/2" to 25". Swivel heads allow
access to tight areas.
•Large, rectangular swivel mirror is 2" x 3-1/2", and is
attached to one telescoping handle; small mirror is 1-1/4"
in diameter, and is interchangeable with magnets on the
other handle.
•Magnets can lift up to 8 lbs.
No. 4650 – Mirror and magnet set. Wt., 13 oz.
4650
193
GENERAL PURPOSE TOOLS
Misc. Tools
Differential Housing Spreader
Here’s a tool that eases the job of removing or installing
differential ring-gear assemblies on Dana axle models 30
through 70. It’s a heavy-duty device using mechanical
screw power to spread the housing. It
helps prevent the component damage
that often results from the use of
homemade devices.
No. 7071 – Differential housing spreader.
Wt., 34 lbs.
7071
Universal Outside Thread Chaser
Damaged bolt or nut threads can be an annoying, costly
problem–unless you have one of our thread chasers. It will
quickly restore threads to near original condition without the
use of expensive thread-cutting equipment.
•Replaceable V-pads and dies.
•1-1/4" to 5" O.D.
No. 7402 – Thread chaser with 6 dies: threads per inch - 4,
5, 6, 7, 7-1/2, 8, 9, 10, 11, 11-1/2, 12, 14, 16, 18, 20, and
24. Wt., 2 lbs., 13 oz.
No. 216884 – Standard die set. Includes 6 dies, in the sizes
listed above. Wt., 3 oz.
No. 202817 – Metric die set. Includes three dies: 1 mm1.25 mm-1.5 mm-1.75 mm, 2 mm-2.5 mm-3.0 mm-3.5 mm;
4 mm pitch dies. Wt., 3 oz.
No. 206803 – V-pad. Wt., 10 oz.
7402
OTC
No.
Size
Fits Set
Screws
Fits HH
Cap Screws
7345* 1/16"
6
–
7346* 5/64"
8
–
7347* 3/32" 10 & 12
–
7348* 1/8"
1/4"
8
7349* 5/32"
5/16"
10
7350* 3/16"
3/8"
1/4"
7351* 7/32"
7/16"
5/16"
7352* 1/4"
1/2"
3/8"
7353* 5/16"
5/8"
3/8" & 7/16"
7354* 3/8"
3/4"
1/2"
7355† 7/16"
13/16"
9/16"
7356† 1/2"
7/8"
5/8"
7357† 9/16" 1" & 1-1/8"
3/4"
7358† 5/8" 1-1/4" & 1-3/8"
1"
7359† 3/4"
1-1/2"
1-1/8" & 1-1/4"
7360† 1" 1-3/4" & 2"
1-1/2"
Hex Key Wrenches
Allen head cap screws are everywhere, which makes a set
of these wrenches a necessity.
•They’re extra long for added leverage and accessibility.
•Meets ANSI specs.
No. 7365 – Plastic pouch containing wrench Nos. 7345
through 7354. Wt., 15 oz.
7365
* Included in No. 7365 set.
† Available separately; not included in set.
OTC No.
7334 7321*
7322*
7323*
7324*
7325*
7326*
7327*
7328*
7329*
7330†
7331†
7332†
7333†
Size (mm)
1.5
2
2.5
3
4
5
6
8
10
12
14
17
19
* Included in No. 7334 set.
194
† Available separately; not
included in set.
Metric Hex Key Wrench Set
These long-arm hex key wrenches provide added
leverage and accessibility.
•Rust-resistant black oxide finish.
•There are 9 sizes, from 1.5 mm to 10 mm.
•Available separately: 12 mm, 14 mm, 17 mm, and 19 mm.
No. 7334 – Metric hex key set in plastic pouch. Sizes: 1.5
mm, 2 mm, 2.5 mm, 3 mm, 4 mm, 5 mm, 6 mm,
8 mm, and 10 mm. Wt., 15 oz.
GENERAL PURPOSE TOOLS
Misc. Tools
Windshield Wiper Puller
•Removes wiper arms on many foreign and domestic cars
and light trucks.
•Will not damage wiper arm or hood cowling during removal.
•Simply place puller feet under wiper arm and tighten
forcing screw against wiper shaft.
No. 4676 – Windshield wiper puller. Wt., 4 oz.
4676
Metric/SAE T-Handle Motorcycle Kit
•7-piece metric tool kit with ball point and hex key ends for
motorcycles, autos, and diesel trucks contains adapters:
1.5 mm, 2.0 mm, 2.5 mm, 3.0 mm, 4.0 mm, 5.0 mm, 6.0
mm, and one driver handle/holder.
•7-piece standard tool kit with ball point and hex key
ends for motorcycles, autos, and diesel trucks contains
adapters: 1/16", 5/64", 3/32", 1/8", 5/32", 3/16", 1/4", and
one driver handle/holder.
•Combines low-torque handle with key storage!
No. 4710 – Metric/SAE T-handle motorcycle kit.
Wt., 15 oz.
4710
Motorcycle / ATV Chain Tension Puller
•Tool is designed to work on drive chains found on
motorcycles and all-terrain vehicles (ATVs). Fits the
following size chains: 428, 520, 525, 528, and 530.
•Tool jaws fit in chain link ends. Tightening the forcing
screw pulls the jaws together to hold the chain for easy removal or installation of the chain connector or master
link.
No. 4758 – Motorcycle/ATV chain tension puller. Wt., 13 oz.
4758
Universal Pulley Holder
•Universal design fits many different size pulleys having
slots or holes, such as camshaft pulleys or crankshaft
pulleys.
•Wrench is adjustable from 1-1/2" to 8-5/8"; four different
size step pins are interchangeable.
•Long handle enables technician to easily hold the pulley when tightening or loosening retaining bolts.
No. 4754 – Universal pulley holder. Wt., 4 lbs., 15 oz.
4754
195
GENERAL PURPOSE TOOLS
Pullers & Wrenches
Heavy-Duty Wiper Arm Puller
• Designed to remove aluminum wiper arm from the steel
stud that often galvanizes, locking the arm and stud
together.
• Investment cast design is strong, easier to use, and saves
time.
• Live center and more precise alignment save labor. Works
on these and many other vehicles: Jeep Liberty, Grand
Cherokee, Dodge Caravan, Stratus, Ram Diesels, Dakota
& PT Cruiser, Chrysler LHS, Town & Country, Saturn Vue
Buick Rendevous, Cadillac CTS, Ford Focus,
Ford Windstar, Honda Civic, Odyssy Toyota Camry.
No. 6676 – Heavy-duty wiper arm puller. Wt., 12 oz.
6676
Variable Pin Spanner Wrench
6613
•Universal design fits many different types of pulleys
having slots or holes, including camshaft pulleys and
crankshaft pulleys.
•Wrench is adjustable from 1-1/4 inch to 5 inches; works
with a 1/2 inch ratchet or breaker bar.
Replacement Parts:
No. 526908-1 – 3.5 mm pin
No. 526908-2 – 4 mm pin
No. 526908-3 – 4.5 mm pin
No. 526908-4 – 5 mm pin
No. 526908-5 – 6 mm pin
No. 526908-6 – 7 mm pin
No. 526908-7 – 10 mm pin
No. 526908-8 – Handle
No. 6613 – Variable pin spanner wrench. Wt., 2 lbs.
Giant Adjustable Wrenches
7640
7641
The really big jobs call for really big tools. These wrenches
will handle 42 bolt sizes from 1-3/8" to 4-3/4". Together, both
wrenches weigh just 41 lbs., but can replace over 1,000 lbs.
of fixed-size wrenches.
No 7640 – Giant adjustable wrench. Rated to withstand
2,000 ft. lbs. of torque. Wt., 10 lbs. 10 oz.
No. 7641 – Giant adjustable wrench. Rated to withstand
5,000 ft. lbs. of torque. Wt., 30 lbs. 5 oz.
Order
No.
Nut / Bolt Size
Fed. Spec.: GG-W-631B
196
7640
7641
1-3/8" to 2-7/8"
2-3/4" to 4-3/4"
Increments
of Jaw
Adjustment
Lgth.
1/8"
1/8"
24"
36"
Head
Thickness
7/8"
1-1/8"
Wt.
(lbs.)
10.6
30.3
GENERAL PURPOSE TOOLS
Spanner Wrenches & Stud Remover
Adjustable Spanner Wrench
This tool is Ideal for adjusting pillow block bearings. It also
works well on International model “M” water pumps and on
all International power-takeoff units.
•This wrench adjusts from 1/2" to 2-3/4".
No. 7246 – Adjustable spanner wrench. 9-1/4" long.
Wt., 11 oz.
7246
Adjustable Hook Spanner Wrench
885
Here’s a tool that’s needed wherever turret adjusting nuts
or packing gland nuts are used.
•Capacity is 1-1/2" to 4".
•Handle is 24" long, 11/16" diameter.
No. 885 – Adjustable hook spanner wrench. Wt., 3 lbs., 2 oz.
Fed. Spec.: GGG-W-665b
Heavy-Duty Adjustable Hook
Spanner Wrench
Some jobs require beefier tools. Here’s a wrench to fill that
need. It’s drop-forged and features extra heavy construction
and a 3/4" thick, 11-position hook jaw that’s capable of gripping fasteners from 4-3/4" to 12-3/4" O.D.
•Handle is 25-3/4" long and 15/16" in diameter.
No. 7309 – Heavy-duty adjustable hook spanner wrench.
Wt., 13 lbs., 7 oz.
Fed. Spec.: GGG-W-665b
7309
Adjustable Hook Spanner Wrenches
These pieces will replace many fixed-size wrenches
needed to service industrial tractors and other equipment.
Their drop-forged jaws adjust to 11 positions for a capacity
of 4-3/4" to 12-3/4" O.D.
•Handle is 24" long and 1" in diameter.
No. 7307 – Spanner wrench with one 3/8" thick jaw.
Wt., 5 lbs., 15 oz.
No. 7308 – Spanner wrench with two interchangeable jaws:
one 3/8" thick, one 3/4" thick. Wt., 11 lbs., 7 oz.
Fed. Spec.: GGG-W-665b
7307
Stud Remover Sets
These metric and SAE, 4-piece, stud remover sets offer the
best professional extractors available. Designed and tested
to reach studs in difficult work areas.
•Housed in a blow-molded storage case.
No. 6986-1 – 1/4" stud remover No. 6986-2 – 5/16" stud remover
No. 6986-3 – 3/8" stud remover No. 6986-4 – 7/16" stud remover
No. 6986 – SAE stud remover set. 3/8" drive for 1/4" and
5/16" stud sizes, and 1/2" drive for 3/8" and 7/16" stud sizes.
Wt., 1 lb., 2 oz.
No.
No.
No.
No.
6987-6 – 6 mm stud remover
6987-8 – 8 mm stud remover
6987-10 – 10 mm stud remover
6987-12 – 12 mm stud remover
No. 6987 – Metric stud remover set. 3/8" drive for 6 mm and
8 mm stud sizes, and 1/2" drive for 10 mm & 12 mm stud
sizes. Wt., 1 lb., 2 oz.
6987
197
GENERAL PURPOSE TOOLS
Drivers & Pullers
Bearing Race and Seal Driver Set
4507
(10 piece)
•This aluminum constructed set permits installation of tapered bearing races and seals without damage to the
component or housing.
•Tapered side of driver is used to install races. Invert the
driver to the flat side to install seals.
•Set is housed in a blow-molded plastic storage case.
•Includes driver handle with bolt, plus these tool sizes: 1.565", 1.750", 1.965", 2.325", 2.470", 2.555", 2.830", 2.995", and 3.180".
No. 4507 – Bearing race and seal driver set (10 piece).
Wt., 4 lbs., 2 oz.
Metric Bushing Driver Set
4407
• 14-piece tool kit for motorcycles, Asian and European vehicles contains adapters: 10-12 mm, 14-16 mm, 15-17
mm, 16-18 mm, 18-20 mm, 20-22 mm, 22-24 mm, 25-27
mm, 28-30 mm, 30-34 mm, 32-36 mm, 35-40 mm, 38-42
mm; one small driver handle; one medium driver handle;
one large driver handle.
• Aluminum construction won’t mar the bushing or affect
bushing tolerance, which is critical for efficient operation of
the engine, transmission, and hubs.
No. 4407 – Metric bushing driver set. Wt., 2 lbs.
Similar to Ford
No. D80L-522-A
522
Using this tool, you can easily remove a wide range of
gears, pulleys, or other parts that have tapped holes.
•The puller will spread from 2" to 7-3/4". Its block is
8-1/4" wide, and its forcing screw is 3/4"-16 x 11-5/8"
long.
•Accommodates any cap screws up to 1/2" diameter.
No. 522 – Large gear and pulley puller. Wt., 4 lbs., 8 oz.
Gear and Pulley Pullers
7393
These tools are perfect for removing timing gears, fan
pulleys, harmonic balancers, and many other parts
having tapped holes.
•Each puller will spread from 1-1/2" to 4-1/4". The puller blocks are 4-7/8" wide.
•Both include two hex head cap screws, 3/8"-16 x 3"
long.
No. 7392 – Puller with 13" long screw.
Wt., 2 lbs., 4 oz.
No. 7393 – Puller with 5-1/2" long screw.
Wt., 1 lb., 8 oz.
7392
198
Large Gear and Pulley Puller
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement