INSTALLATION INSTRUCTIONS Gas Cooktop US CA CG244D, CG305D & CG365D

Add to my manuals
24 Pages

advertisement

INSTALLATION INSTRUCTIONS Gas Cooktop US CA CG244D, CG305D & CG365D | Manualzz

INSTALLATION INSTRUCTIONS

Gas Cooktop

CG244D, CG305D & CG365D models

US CA

www.fisherpaykel.com

590486E 04.15

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

1

SAFETY AND WARNINGS

!

WARNING!

Electrical Shock Hazard

Disconnect product from the mains power supply before servicing. This appliance is equipped with a three-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded power outlet. Do not under any circumstances cut or remove the grounding prong from this plug.

Failure to follow this advice may result in electrical shock or death.

!

WARNING!

Cut Hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or cuts.

IMPORTANT SAFETY INSTRUCTIONS

This appliance shall be installed in accordance with the installation requirements of the local gas authority or the appropriate installation code or in the absence of local codes with the latest National Fuel Gas Code NFPA 54/ANSI Z223.1 or CAN/CSA B149.1,2

(Canada). Local building and electrical codes must be adhered to.

Electrical installation must be in accordance with the National Electrical Code, ANSI/

NFPA70 - latest edition or CSA C22.1 (Canada) and/or local codes.

Installation in manufactured (mobile) home: installation must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part

280)] or, when such standard is not applicable, the Standard for Manufactured Home

Installations, ANSI/NFPA 225, or with local codes where applicable.

Installation in Recreational Park Trailers: installation must conform with state or other codes or, in the absence of such codes, with the Standard for Recreational Park Trailers,

ANSI A119.5.

Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.

Flexible appliance connectors shall meet the requirements of ANSI Z21.24 and State

Boards. They shall not exceed 35 1/2 inches (900 mm) in length. In order to avoid hazard, these appliances must be installed according to these instructions.

This appliance must be installed by an authorized person (Warning: this appliance must be installed by a licensed plumber or gas fitter when within the Commonwealth of

Massachusetts).

Please make this information available to the person installing the appliance as it could reduce your installation costs.

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

Please leave these instructions with the appliance. Inform the customer to retain for future reference and for the local inspectors’ use.

Failure to install the appliance correctly could invalidate any warranty or liability claims.

Leak testing of the appliance shall be conducted according to the manufacturer’s instructions.

Only genuine replacement parts may be used for servicing the appliance. These are available from your nearest Fisher & Paykel Service Center.

Before you install the appliance, please make sure that

the local distribution conditions (nature of gas and pressure) and the adjustment of the appliance are compatible. For adjustment conditions for this appliance, see ‘Gas rate summary’ under step 3. a suitable isolating switch is incorporated in the fixed wiring in an acceptable position.

the appliance is connected to a power outlet that is electrically grounded in accordance with local codes or in the absence of local codes, with the National Electric Code ANSI/

NFPA 70 or CSA C22.2 (Canada).

there is a power outlet (110-120V 60Hz) within reach of the appliance cable (35 1/2” (900 mm) from the center rear of the appliance). This must be accessible after installation. The mains power supply cable should not touch any metal parts.

the countertop is square and level and no structural members interfere with space requirements the countertop is made of heat-resistant material.

you take note of the following recommended non-combustible materials: 1/4” (6 mm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 1/32” (0.4 mm) stainless steel,

1/32” (0.6 mm) aluminum or 1/32” (0.5 mm) copper.

the gas shut-off valve is accessible after installation.

if the power supply cable is damaged, it is replaced only by the special cable: Part no.

531954 FLEX TERMINAL BLOCK ASSY US, obtainable from authorized Fisher & Paykel

Service Agents.

1

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

2

PARTS SUPPLIED

Wok stand (1)

SEMI-RAPID

MINI WOK

CG244D

AUX

Small pan support

(1)

(CG305D & CG365D models only)

SEMI-RAPID SEMI-RAPID

RAPID

CG305D & CG365D

Fibre washers (1)

Elbow 1/2“ NPT external thread (1)

3

GAS RATE SUMMARY

Clamping brackets (4) and screws (4)

DUAL WOK

SEMI-RAPID

AUX

Regulator (1) Foam tape (1)

High Altitude Installations - CG30D & CG365D models

For installations above 3000’ conversion kits are required:

3,000-6,000’ 534695 KIT HI ALT NG

534697 KIT HI ALT LP

6000’+ 534696 KIT HI ALT NG

534698 KIT HI ALT LP

High Altitude Installations - CG244D models

For installations above 3000’ conversion kits are required:

3,000-6,000’ 535432 KIT HI ALT 3000-6000 NG GOS244

535434 KIT HI ALT 3000-6000 LG GOS244

6000’+ 535433 KIT HI ALT 6000+ NG GOS244

535435 KIT HI ALT 6000+ LG GOS244

Contact your authorized dealer, customer care or refer to the website listed at the back of this document.

US CA

NG 4” H2O (0.15 psi)*

LP 11” H2O (0.39 psi)*

CG244D

CG305D

CG365D

0.9

NG

3500

AUX

LP

0.55

3500 1.40

NG

SEMI-RAPID

LP

8500 0.75

6700

0.9

3500 0.55

3500 1.40

8500 0.75

6700

0.9

3500 0.55

3500 1.40

8500 0.75

6700 na

NG

RAPID na na

LP na

1.65

11500 0.98

11500

1.65

11500 0.98

11500

1.55

NG

MINI WOK

LP

11100 0.94

11100 na na na na na na na na na

NG

DUAL WOK

LP na na na

1.50

1.50

0.70

1.50

1.50

0.70

19000

19000

0.83

0.83

0.50

0.83

0.83

0.50

19000

19000

2

4

PRODUCT & CABINETRY DIMENSIONS

B

G

C

H

A

K

TOP

Note: Gas inlet connection is located in the rear right corner.

E

REAR

D

3

PRODUCT DIMENSIONS

A

Overall height of product

(excluding burners, dials and pan supports)

B

Overall width of product

C

Overall depth of product

D

Height of chassis

(below top of counter)

E

Width of chassis

F

Depth of chassis

G

Overall width of cutout

H

Overall depth of cutout

I

Corner radius of cutout

J

Distance from top of counter to center of gas inlet on product

K

Distance from edge of chassis to gas inlet on product

J

F

SIDE

CG244D inches (mm)

2 1/2” (64)

23 5/8” (600)

20 7/8” (530)

2 5/16” (59)

21 7/8” (555)

19 1/8” (486)

22 1/16” (560)

19 5/16” (490) max. 3/8” (10)

1 1/4” (32)

13/16” (21)

CG305D inches (mm)

2 1/2” (64)

29 1/2” (749)

20 7/8” (530)

2 5/16” (59)

27 1/2” (698)

19 5/16” (490)

27 3/4” (705)

19 1/2” (495) max. 3/8” (10)

1 1/4” (32)

13/16” (21)

CG365D inches (mm)

2 1/2” (64)

35 1/2” (900)

20 7/8” (530)

2 5/16” (59)

33 11/16” (856)

19 1/8” (486)

34 1/16” (865)

19 5/16” (490) max. 3/8” (10)

1 1/4” (32)

13/16” (21)

I

TOP

FRONT

5

CLEARANCE DIMENSIONS

F

F

C

C

E

G

E

H

G

H

A

A

D

D

I

I

J

J

B

B

ISO

CLEARANCE DIMENSIONS

A

Minimum clearance from left edge of product to nearest vertical surface

B

Minimum clearance from right edge of product to nearest vertical surface

C

Minimum clearance from rear edge of product to:

nearest combustible surface

nearest non-combustible surface*

D

Minimum clearance from front edge of counter to front edge of product

E

Minimum clearance from cooking surface to combustible surface centered above the cooking surface

F

Maximum overall depth of overhead cabinetry

G

Minimum distance between overhead cabinets installed to either side of product

H

Minimum vertical distance between counter and cabinet extending above the counter

I

Minimum clearance below top of countertop to:

nearest combustible surface

F&P oven or nearest non-combustible surface

J

Maximum distance from the center of the product to the nearest grounded power outlet.

The power supply cable must not touch any hot metal surfaces.

* Recommended non-combustible materials are: 1/4” (6 mm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015” (0.4 mm) stainless steel,

0.024” (0.6 mm) aluminum or 0.020” (0.5 mm) copper.

FRONT

CG244D inches (mm)

5 1/8” (130)

4 1/2” (115)

6 5/16” (160) less than 1 3/4” (45)

1 1/4” (32)

36 ” (915)

13” (330)

36” (915)

18” (457)

2 3/4” (70)

2 9/16” (65)

35 1/2” (900)

CG305D inches (mm)

5 1/8” (130)

4 1/2” (115)

7 5/16” (186) less than 1 3/4”

(45)

1 1/4” (32)

36 ” (915)

13” (330)

36” (915)

18” (457)

2 3/4” (70)

2 9/16” (65)

35 1/2” (900)

CG365D inches (mm)

5 1/8” (130)

4 1/2” (115)

6 5/16” (160) less than 1 3/4”

(45)

1 1/4” (32)

36 ” (915)

13” (330)

36” (915)

18” (457)

2 3/4” (70)

2 9/16” (65)

35 1/2” (900)

4

500 mm

50 mm

REAR CLAMPS

R S

A

FRONT CLAMPS

A

S F

Fibre washer

Floating nut

Elbow (½” BSP external thread) x 4

PTFE

1

3⁄8

NPT

2

LPG test point adaptor (if using LPG)

16-20mm

20-30mm 30-40mm

40mm+

Floating nut

Fibre washer Elbow (½” BSP external thread)

x 4

Adhesive side

Foam Tape

2

NG Models

Washer

Arrow

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two semi-rapid burners operating at highest setting.

LPG Models

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with the two semi-rapid burners operating at highest setting.

ALL Models

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

check all connections

500 mm

25 mm

500 mm

25 mm

1

2

1

20-50 mm x 4

NG

NG

½

“ BSP

LPG

LPG

½

“ BSP

lifting off yellow tip good flame

500 mm

50 mm

7

FIT THE ELBOW AND WASHER

6

DISCARD PACKAGING

Model may vary from illustrations shown

Fibre washer

Floating nut x 4

Elbow (½” BSP external thread)

PTFE

16-20mm

1

3⁄8

NPT

LPG test point adaptor (if using LPG)

20-30mm

2

30-40mm

40mm+

Fibre washer

Floating nut

Elbow (½” BSP external thread)

500 mm

50 mm

Recycle responsibly

1

3⁄8

NPT

8

APPLY ADHESIVE FOAM TAPE AROUND EDGE

Ensure edge of tape lines up with outer edge of cooktop

Foam Tape

500 mm

25 mm

Adhesive side

Floating nut

REAR CLAMPS

Fibre washer

FRONT CLAMPS

Elbow (1/2 “ NPT external thread)

A

A

500 mm

25 mm

R S

9

LOWER GENTLY INTO THE CUTOUT

S

F

Floating nut Fibre washer Elbow (½” BSP external thread)

PTFE

2

x 4

LPG test point adaptor (if using LPG) x 4

5

Floating nut

16-20mm

Fibre washer

20-30mm 30-40mm

Elbow (½” BSP external thread)

Ensure edge of tape lines up with outer edge of cooktop

40mm+

Foam Tape

Adhesive side

1

x 4

2

Spread the seal around the edges, with the adhesive side facing down to form a continuous seal around the cooktop.

3

Using a sharp cutter or trimmer knife, trim the excess sealing material around the edge of the cooktop. Take care not to damage the countertop.

2

NG Models

Washer

LPG Models

Arrow

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two semi-rapid burners operating at highest setting.

yellow tip

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with the two semi-rapid burners operating at highest setting.

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

NG Models

Washer

Arrow

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two semi-rapid burners operating at highest setting.

25 mm

LPG Models

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with the two semi-rapid burners operating at highest setting.

ALL Models

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

25 mm

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

check all connections

1

2

Ensure edge of tape lines up with outer edge of cooktop

20-50 mm

NG x 4

1

Nipple (½” NPT thread)

check all connections

NG LPG

½

“ BSP

½

“ BSP

NG

LPG

REAR CLAMPS

R

S

A

1

1

FRONT CLAMPS

A

S F

2

20-50 mm

NG

Adhesive side

½

“ BSP

LPG

Foam Tape

LPG

½

“ BSP

x 4

lifting off yellow tip good flame

500 mm

50 mm

REAR CLAMPS

R

S

A

FRONT CLAMPS

A

S

F

Fibre washer

Floating nut

Elbow (½” BSP external thread)

Adhesive side

Foam Tape

1

3⁄8

NPT

PTFE

x 4

Floating nut

Adhesive side

Fibre washer

Foam Tape

2

!0

FIT CLAMPING BRACKETS BASED ON THE COUNTERTOP THICKNESS & SECURE TO COUNTERTOP

Elbow (½” BSP external thread)

1

view from below

2

x 4

Floating nut

20 mm

Fibre washer

LPG test point adaptor (if using LPG)

50 mm

x 4

”-

¾

(16-20mm)

¾

”- 1 ”

(20-30mm)

1 ”- 1

½

(30-40mm)

½

” +

NG

Repeat on all the other sides

LP

If converting to LP, see 17 'Converting to a different gas type'

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

The appliance must be isolated from the gas supply piping system by closing its individual shut-off valve during any pressure testing of the gas supply piping system at test pressures at or less than 1/2 p.s.i. (3.5 kPa).

Maximum inlet gas supply pressure 20” W.C. (5 kPa). Minimum gas supply pressure for regulator testing 5” W.C. Natural Gas / 12” W.C LP gas.

recessed to 50 mm

+50 mm

ALL Models

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two

semi-rapid burners operating at highest setting.

A manual shut-off valve must be installed in an accessible location in the gas line external to the appliance for the purpose of turning on or shutting off gas to the appliance. (In Massachusetts, such shut-off devices should be approved by the Board of State Examiners of Plumbers

& Gas Fitters).

NPT external thread on one end and a 1/2” NPT one on the other

Washer

!1

GAS CONNECTION

is fitted with an isolating valve close to the cooktop.

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with

the two semi-rapid burners operating at highest setting.

To enable the gas supply to be readily shut off by the customer, make sure the connection

If connecting the gas with a flexible hose:

If connecting the gas with a flexible hose

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 5 CLEARANCE DIMENSIONS.

The hose assembly must be with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with the relevant requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

6

16-20mm

20-30mm 30-40mm

40mm+ check all connections

2

NG Models

Washer

Arrow

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two

semi-rapid burners operating at highest setting.

LPG Models

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with

the two semi-rapid burners operating at highest setting.

ALL Models

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

check all connections

To check that the ignition system operates correctly, light each burner by itself, then all burners in combination.

Check for a well‐defined blue flame without any yellow tipping.

If any abnormality is evident, check that the components of the burner assembly are located properly

If proper operation cannot be obtained, contact your nearest F&P Authorised Service Centre.

The cooktop must not be used by the customer until proper operation has been achieved.

lifting off yellow tip good flame

lifting off yellow tip good flame

500 mm

25 mm

500 mm

25 mm

1

2

1

20-50 mm x 4

NG

NG

½

“ BSP

LPG

LPG

½

“ BSP

Foam Tape

Adhesive side

1

7

2

!2

CONNECT TO THE GAS SUPPLY

Floating nut

Fibre washer

This appliance is factory set for use with Natural Gas at 4” W.C.P. or LP

Gas at 11” W.C.P. Check the label on the underside of the appliance.

● ●

Gas regulator

For use with a gas pressure regulator as shown.

20 mm

Elbow (½” BSP external thread)

Cooktop

To Cooktop

NG

LPG

If converting to LPG, see 16 'Converting to a different gas type'

Regulator

Washer

Arrow

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two semi-rapid burners operating at highest setting.

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with the two semi-rapid burners operating at highest setting.

Solid or Flexible

Connector

Pressure

50 mm

shows

Direction of

Gas Flow

recessed to 50 mm

Shut-Off

Valve

+50 mm

Pipe Stub from

House supply

ALL Models

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 5 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

!3

LEAK TESTING

check all connections

● ●

● ●

● ●

● ●

● ●

Leak testing of the appliance shall be conducted according to the manufacturer’s instructions.

The appliance and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system in excess of 1/2 psi (3.5kPa).

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures at or less than 1/2 psi (3.5 kPa).

Maximum inlet gas supply pressure 20” W.C. (5 kPa)

Minimum gas supply pressure for regulator testing 5” W.C. Natural Gas, 12” W.C. LP Gas.

After installing the gas supply and making all connections, check thoroughly for possible leaks:

1

Turn all control dials on unit to “OFF” position.

2

Open the valve on the gas supply.

3

Using a leak detection fluid (eg Rocol leak detection spray), check each gas connection one at a time by spraying or brushing the solution over the connection. The presence of bubbles will indicate a leak.

4

If necessary, tighten the fitting and recheck for leaks.

5

Turn on burner valve and light each burner.

6

Check for a clear blue flame without yellow tipping. If burners show any abnormalities, check that they are located properly and in line with the injector orifice.

Check for a well‐defined blue flame without any yellow tipping.

If any abnormality is evident, check that the components of the burner assembly are located properly

If proper operation cannot be obtained, contact your nearest F&P Authorised Service Centre.

The cooktop must not be used by the customer until proper operation has been achieved.

lifting off yellow tip good flame

!4

AFFIX DUPLICATE DATA LABEL SOMEWHERE

!5

FIT PAN SUPPORTS

Ensure the pan supports are located securely and in the correct orientation (refer to User guide)

Duplicate data label

!6

LEAK TESTING

● ●

● ●

● ●

● ●

● ●

To check that the ignition system operates correctly, light each burner by itself, then all burners in combination.

Check for a well-defined blue flame without any yellow tipping.

If any abnormality is evident, check that the components of the burner assembly are located properly

If proper operation cannot be obtained, contact Customer Care or your nearest F&P Authorized Service Center.

The cooktop must not be used by the customer until proper operation has been achieved.

Lifting off

Yellow tip

Good flame

8

!7

FINAL CHECKLIST

TO BE COMPLETED BY THE INSTALLER

Have you installed the clamping brackets?

Have you verified that the type of model (factory-set for NG or LP) matches the type of gas at the site of installation?

Have you sealed all connections with gas tape?

Have you used the fibre washer supplied?

Have you leak-tested all connections?

Is the cooktop set to the correct working pressure?

Have you affixed the supplied duplicate data plate label on an adjacent surface accessible to the customer?

Is the cooktop grounded?

Check that the power supply cord is NOT touching the cooktop.

OPERATION:

Do all burners ignite both individually and in combination?

Are the flames consistent and appropriately sized?

Have you demonstrated the basic operation to the customer?

9

Complete and keep for safe reference:

Model

Serial No.

Purchase Date

Purchaser

Dealer Address

Installer’s Name

Installer’s Signature

Installation Company

Installation Date

Copyright © Fisher & Paykel 2015. All rights reserved.

The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available.

10

11

12

INSTRUCTIONS D’INSTALLATION

Surface de cuisson au gaz

Modèles

CG244D, CG305D et CG365D

US CA

www.fisherpaykel.com

590486E 04.15

● ●

● ●

● ●

● ●

● ●

● ●

● ●

1

CONSIGNES DE SÉCURITÉ ET MISES EN GARDE

!

MISE EN GARDE!

Risque de choc électrique

Débranchez l’appareil de l’alimentation électrique avant toute réparation.

Cet appareil est équipé d’une fiche à trois broches avec mise à la terre pour protéger des chocs électriques. Branchez-la directement dans une prise

électrique avec mise à la terre adéquate. Vous ne devez en aucune circonstance couper ou retirer la broche de mise à la terre de cette fiche.

Le non-respect de cette consigne peut entraîner un choc électrique ou la mort.

!

MISE EN GARDE!

Risque de coupure

Attention, les bords du panneau sont tranchants.

Des blessures ou des coupures peuvent se produire si vous ne faites pas preuve de prudence.

CONSIGNES DE SÉCURITÉ IMPORTANTES!

Cet appareil devra être installé conformément aux exigences des réglementations locales relatives au gaz ou des codes d’installation appropriés, ou en l’absence de codes locaux, de la norme NFPA 54/ANSI Z223.1 ou CAN/CSA B149.1,2 de la dernière édition du National Fuel Gas Code du Canada. Les codes locaux du bâtiment et de l’électricité doivent être respectés.

Toute installation électrique doit être conforme à la norme ANSI/NFPA70 de la dernière

édition du Code national de l’électricité ou à la norme CSA C22.1 (Canada) et/ou aux codes locaux.

Installation dans une maison préfabriquée (mobile) : l’installation doit être effectuée conformément à la norme Manufactured Home Construction and Safety Standard,

Titre 24 CFR, Partie 3280 [anciennement Federal Standard for Mobile Home Construction and Safety, Titre 24, HUD (Partie 280)] ou, lorsqu’une telle norme est inapplicable, à la norme Standard for Manufactured Home Installations, ANSI/NFPA 225, ou aux codes locaux en vigueur.

Installation dans une caravane de parc : l’installation doit être effectuée conformément aux codes de l’État et autres codes, ou en l’absence de tels codes, à la norme Standard for Recreational Park Trailers, ANSI A119.5.

Ne retirez pas les étiquettes, mises en garde ou plaques signalétiques apposées sur l’appareil. Cela pourrait entraîner l’annulation de la garantie.

Les raccords flexibles de l’appareil doivent être conformes à la norme ANSI Z21.24 et aux règlements de commissions d’État. Leur longueur ne doit pas dépasser 35 1/2 po

(900 mm). Installez ces appareils conformément aux instructions afin d’éviter tout danger.

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

Cet appareil doit être installé par un technicien autorisé (mise en garde : dans les limites de l’État du Massachusetts, cet appareil doit être installé par un monteur d’installation au gaz ou plombier autorisé).

Remettez ces instructions à la personne qui installera l’appareil. Cela pourrait réduire vos coûts d’installation.

Laissez ces instructions avec l’appareil. Demandez au client de les conserver pour toute référence ultérieure ou vérification des inspecteurs locaux.

Le fait de ne pas installer l’appareil de façon adéquate pourrait entraîner l’annulation de toute garantie ou réclamation.

La vérification des fuites doit être effectuée conformément aux instructions du fabricant.

Utilisez uniquement des pièces de remplacement authentiques pour effectuer l’entretien ou les réparations de l’appareil. Vous pouvez vous les procurer auprès d’un Centre de service Fisher & Paykel de votre région.

Avant d’installer l’appareil, assurez-vous que :

les conditions de distribution locales (nature du gaz et pression) et le réglage de l’appareil sont compatibles. Pour connaître les conditions de réglage de cet appareil, voir ‘Tableau de débit des gaz’ à l’étape 3. le câblage fixe comporte un interrupteur de sectionnement approprié, installé dans une position convenable.

l’appareil est branché à une prise électrique mise à la terre en conformité avec les codes locaux ou, en l’absence de tels codes, avec la norme ANSI/NFPA 70 ou CSA C22.2 du Code national de l’électricité (Canada).

une prise électrique (110-120 V 60 Hz) se trouve à proximité du câble de l’appareil

(35 1/2 po (900 mm) à partir de la partie centrale à l’arrière de l’appareil). Cette prise doit demeurer accessible après l’installation. Le câble d’alimentation ne doit toucher aucune pièce métallique.

le comptoir est au niveau et bien droit, et aucune pièce de charpente ne nuit aux exigences de dégagement.

le comptoir est fait d’un matériau résistant à la chaleur.

vous prenez note de ces matériaux incombustibles recommandés : panneau de celloderme ignifuge de 1/4 po (6 mm) couvert d’une tôle d’acier n° 28 MSG (minimum), d’acier inoxydable de 1/32 po (0,4 mm),

d’aluminium de 1/32 po (0,6 mm) ou de cuivre de 1/32 po (0,5 mm).

le robinet d’arrêt du gaz est accessible après l’installation.

si le câble d’alimentation est endommagé, il doit être remplacé uniquement par un câble spécial : Pièce n° 531954 FLEX TERMINAL BLOCK ASSY US, disponible auprès des agents de service autorisés de Fisher & Paykel.

1

IMPORTANT!

CONSERVEZ CES INSTRUCTIONS

Les modèles illustrés dans ce document pourraient ne pas être offerts par tous les détaillants et sont sujets à modifications sans préavis. Pour les plus récentes informations sur la disponibilité des modèles et des caractéristiques dans votre pays, veuillez visiter notre site Web local à l’adresse indiquée à la fin de ce document, ou contacter votre détaillant Fisher & Paykel local.

2

PIÈCES FOURNIES

Support de wok (1)

SEMI-RAPIDE

MINI WOK

CG244D

Petite pièce d’appui (1)

(Modèles CG305 et

CG365 seulement.)

SEMI-RAPIDE

AUXILIAIRE

SEMI-RAPIDE

RAPIDE

CG305D et CG365D

Rondelle en fibre (1)

Coude avec filetage

NPT externe de

1/2 po (12,5 mm) (1)

3

TABLEAU DE DÉBIT DES GAZ

Supports de retenue (4) et vis (4)

DOUBLE POUR

WOK

SEMI-RAPIDE

AUXILIAIRE

Régulateur (1) Isolant adhésif (1)

Installations en haute altitude - Modèles CG30D & CG365D

Pour les installations au-dessus de 3 000 pi, des ensembles de conversion sont requis :

3 000-6 000 pi 534695 – ENSEMBLE HAUTE ALTITUDE POUR GN

534697 – ENSEMBLE HAUTE ALTITUDE POUR GPL

6 000 pi+ 534696 – ENSEMBLE HAUTE ALTITUDE POUR GN

534698 – ENSEMBLE HAUTE ALTITUDE POUR GPL

Installations en haute altitude - Modèles CG244D

Pour les installations au-dessus de 3 000 pi, des ensembles de conversion sont requis :

3 000-6 000 pi 535432 KIT HI ALT 3000-6000 NG GOS244

535434 KIT HI ALT 3000-6000 LG GOS244

6 000 pi+ 535433 KIT HI ALT 6000+ NG GOS244

535435 KIT HI ALT 6000+ LG GOS244

Communiquez avec votre détaillant autorisé ou l’assistance à la clientèle, ou consultez notre site Web, à l’adresse indiquée à l’arrière de ce document.

US CA

GN 4 po (102 mm) H2O

(0,15 psi)*

GPL 11 po (279 mm) H2O

(0,39 psi)*

CG244D

GN

AUXILIAIRE

GPL

0.9

3500 0.55

3500

GN

SEMI-RAPIDE

GPL

1.40

8500 0.75

6700

CG305D

CG365D

0.9

3500 0.55

3500 1.40

8500 0.75

6700

0.9

3500 0.55

3500 1.40

8500 0.75

6700

GN

RAPIDE

GPL GN

MINI WOK

GPL

DOUBLE POUR WOK

GN GPL na na na na

1.65

11500 0.98

11500

1.65

11500 0.98

11500

1.55

11100 0.94

11100 na na na na na na na na na na na na

1.50

1.50

0.70

1.50

1.50

0.70

19000

19000

0.83

0.83

0.50

0.83

0.83

0.50

19000

19000

2

4

PRODUCT & CABINETRY DIMENSIONS

B

G

C

H

DESSUS

Remarque : Le raccord d’admission de gaz est situé dans le coin arrière droit.

A

K

D

E

ARRIÈRE

3

Dimensions du produit et des armoires

A

Hauteur hors tout du produit (excluant les brûleurs, les boutons et les pièces d’appui)

B

Largeur hors tout du produit

C

Profondeur hors tout du produit

D

Hauteur du châssis (sous la surface du comptoir)

E

Largeur du châssis

F

Profondeur du châssis

G

Largeur hors tout de l’ouverture

H

Profondeur hors tout de l’ouverture

I

Rayon du coin de l’ouverture

J

Distance entre la surface du comptoir et le centre de l’admission de gaz du produit

K

Distance entre le rebord du châssis et l’admission de gaz du produit

F

CÔTÉ

J

CG244D

2 1/2 po (64)

23 5/8 po (600)

20 7/8 po (530)

2 5/16 po (59)

21 7/8 po (555)

19 1/8 po (486)

22 1/16 po (560)

19 5/16 po (490) max. 3/8 po (10)

1 1/4 po (32)

13/16 po (21)

CG305D

2 1/2 po (64)

29 1/2 po (749)

20 7/8 po (530)

2 5/16 po (59)

27 1/2 po (698)

19 5/16 po (490)

27 3/4 po (705)

19 1/2 po (495) max. 3/8 po (10)

1 1/4 po (32)

13/16 po (21)

I

DESSUS

DEVANT pouces (mm)

CG365D

2 1/2 po (64)

35 1/2 po (900)

20 7/8 po (530)

2 5/16 po (59)

33 11/16 po (856)

19 1/8 po (486)

34 1/16 po (865)

19 5/16 po (490) max. 3/8 po (10)

1 1/4 po (32)

13/16 po (21)

A

F

F

C

A

D

B

ISO

D

B

C

5

DIMENSIONS DE DÉGAGEMENT

I

E

G

I

J

E

H

G

J

Dimensions de dégagement

A

Dégagement minimal entre le côté gauche du produit et la surface verticale la plus proche

B

Dégagement minimal entre le côté droit du produit et la surface verticale la plus proche

C

Dégagement minimal entre l’arrière du produit et :

La surface combustible la plus proche

La surface incombustible la plus proche*

D

Dégagement minimal entre le devant du comptoir et le devant du produit

E

Dégagement minimal entre la surface de cuisson et une surface combustible centrée au-dessus de la surface de cuisson

F

Profondeur hors tout maximale des armoires suspendues

G

Distance minimale entre les armoires suspendues installées des deux côtés du produit

H

Distance verticale minimale entre le comptoir et une armoire au-dessus du comptoir

I

Dégagement minimal entre le dessous du comptoir et :

La surface combustible la plus proche

Une cuisinière f&p ou la surface incombustible la plus proche

J

Distance maximale entre la partie centrale du produit et la prise électrique avec mise à la terre la plus proche.

Le câble d’alimentation ne doit toucher aucune surface métallique chaude.

* Les matériaux incombustibles recommandés sont : panneau de celloderme ignifuge de 1/4 po (6 mm) couvert d’une tôle d’acier n° 28 MSG (minimum), d’acier inoxydable de 0,015 po (0,4 mm), d’aluminium de 0,024 po (0,6 mm) ou de cuivre de 0,020 po (0,5 mm).

H

DEVANT

CG244D

5 1/8 po (130)

4 1/2 po (115)

CG305D

5 1/8 po (130)

4 1/2 po (115)

pouces (mm)

CG365D

5 1/8 po (130)

4 1/2 po (115)

6 5/16 po (160) moins de 1 3/4 po

(45)

1 1/4 po (32)

36 po (915)

13 po (330)

36 po (915)

18 po (457)

7 5/16 po (186) moins de 1 3/4 po

(45)

1 1/4 po (32)

36 po (915)

13 po (330)

36 po (915)

18 po (457)

2 3/4 po (70)

2 9/16 po (65)

35 1/2 po (900)

2 3/4 po (70)

2 9/16 po (65)

35 1/2 po (900)

6 5/16 po (160) moins de 1 3/4 po (45)

1 1/4 po (32)

36 po (915)

13 po (330)

36 po (915)

18 po (457)

2 3/4 po (70)

2 9/16 po (65)

35 1/2 po (900)

4

500 mm

50 mm

REAR CLAMPS

R S

A

FRONT CLAMPS

A

S F

Fibre washer

Floating nut

Elbow (½” BSP external thread) x 4

PTFE

1

3⁄8

NPT

2

LPG test point adaptor (if using LPG)

16-20mm

20-30mm 30-40mm

40mm+

Floating nut

Fibre washer Elbow (½” BSP external thread)

x 4

Adhesive side

Foam Tape

2

NG Models

Washer

Arrow

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two semi-rapid burners operating at highest setting.

LPG Models

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with the two semi-rapid burners operating at highest setting.

ALL Models

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

check all connections

500 mm

25 mm

500 mm

25 mm

1

2

1

20-50 mm x 4

NG

NG

½

“ BSP

LPG

LPG

½

“ BSP

lifting off yellow tip good flame

Fibre washer

Floating nut x 4

Elbow (½” BSP external thread)

PTFE

16-20mm

1

3⁄8

NPT

LPG test point adaptor (if using LPG)

20-30mm

2

30-40mm

500 mm

50 mm

6

METTEZ L’EMBALLAGE AU REBUT

Le modèle peut être différent des illustrations présentées

7

INSTALLEZ LE COUDE ET LA RONDELLE

40mm+

Fibre washer

Floating nut x 4

Elbow (½” BSP external thread)

Foam Tape

500 mm

25 mm

Adhesive side

Ensure edge of tape lines up with outer edge of cooktop

500 mm

Recyclez de façon responsable

50 mm

Écrou flottant

REAR CLAMPS

Rondelle en fibre

A

FRONT CLAMPS

Coude (avec filetage NPT externe de 1/2 po (12,5 mm))

A

1

3⁄8

NPT

8

APPLIQUEZ L’ISOLANT ADHÉSIF AUTOUR DU REBORD

9

DÉPOSEZ L’APPAREIL DOUCEMENT DANS L’OUVERTURE

F

500 mm

25 mm

Floating nut Fibre washer Elbow (½” BSP external thread)

PTFE

2

LPG test point adaptor (if using LPG)

Assurez-vous que le rebord de l’isolant s’aligne avec le rebord extérieur de la surface de cuisson

5

Côté adhésif

Floating nut

Fibre washer

16-20mm

20-30mm 30-40mm

Elbow (½” BSP external thread) x 4

40mm+

Isolant adhésif

1

x 4

2

Appliquez le joint autour des rebords en plaçant le côté adhésif vers le bas, pour obtenir un joint continu autour de la surface de cuisson.

3

Utilisez un outil de coupe tranchant ou des ciseaux pour couper l’excédent de matériel de scellement autour du rebord de la surface de cuisson. Veillez

à ne pas endommager le comptoir.

2

NG Models

Washer

Arrow

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two semi-rapid burners operating at

LPG Models

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with the two semi-rapid burners operating at highest setting.

yellow tip

ALL Models

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

check all connections

NG Models

Washer

Arrow

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two semi-rapid burners operating at highest setting.

LPG Models

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with the two semi-rapid burners operating at highest setting.

ALL Models

25 mm

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

check all connections

1

2

Ensure edge of tape lines up with outer edge of cooktop

NG

20-50 mm x 4

1

NG

½

“ BSP

Nipple (½” NPT thread)

LPG

½

“ BSP

REAR CLAMPS

R

S

A

1

NG

Adhesive side

½

“ BSP

1

LPG

FRONT CLAMPS

A

S F

2

20-50 mm

Foam Tape

LPG

½

“ BSP

x 4

NG

LPG

lifting off yellow tip good flame

500 mm

50 mm

REAR CLAMPS

R

S

A

FRONT CLAMPS

A

S

F

Fibre washer

Floating nut

Elbow (½” BSP external thread)

Adhesive side

Foam Tape

PTFE

1

3⁄8

NPT

Foam Tape

Fibre washer

Elbow (½” BSP external thread)

2

!0

INSTALLEZ LES SUPPORTS DE RETENUE EN LES AJUSTANT À L’ÉPAISSEUR DU COMPTOIR ET FIXEZ L’APPAREIL AU COMPTOIR

1

x 4

2

x 4

Floating nut

Fibre washer

20 mm

16-20mm

Elbow (½” BSP external thread)

LPG test point adaptor (if using LPG)

50 mm

x 4

5⁄8 po - ¾ po

(16 - 20 mm)

¾ po - 1 3⁄16 po

(20 - 30 mm)

1 3⁄16 po -

1 ½ po

(30 - 40 mm)

NG

LP

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

Assurez-vous que le point de raccordement demeure accessible après l’installation de la surface de cuisson.

Pour que le client soit en mesure de couper facilement l’alimentation en gaz, assurez-vous que le raccordement soit muni d’un robinet d’isolement situé

à proximité de la surface de cuisson.

Fermez le robinet d’arrêt individuel de l’appareil pour l’isoler de la tuyauterie d’alimentation en gaz pendant toute vérification de pression de la tuyauterie d’alimentation alors que la pression d’essai est égale ou inférieure à 1/2 psi (3,5 kPa).

recessed to 50 mm

+50 mm

!1

Washer

RACCORDEMENT DU GAZ

ALL Models

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two

semi-rapid burners operating at highest setting.

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

muni de filetage NPT externe de 3/8 po (9,5 mm) à l’une des extrémités, et de filetage NPT de 1/2 po (12,7 mm) à l’autre extrémité.

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with

the two semi-rapid burners operating at highest setting.

Pour le raccordement du gaz à l’aide d’un tuyau flexible

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 5 CLEARANCE DIMENSIONS.

The hose assembly must be with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with the relevant requirements.

L’assemblage du tuyau doit être aussi court que possible et conforme aux exigences applicables.

Le tuyau ne doit pas être entortillé, soumis à l’abrasion ou déformé de manière permanente.

Le tuyau ne doit pas être installé à proximité ou placé en contact avec des surfaces chaudes (p. ex. la base de la plaque chauffante métallique, le conduit de fumée ou le châssis d’une cuisinière sous le comptoir).

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

6

check all connections

20-30mm 30-40mm

40mm+

2

NG Models

Washer

Arrow

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two

semi-rapid burners operating at highest setting.

LPG Models

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with

the two semi-rapid burners operating at highest setting.

ALL Models

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

check all connections

To check that the ignition system operates correctly, light each burner by itself, then all burners in combination.

Check for a well‐defined blue flame without any yellow tipping.

If any abnormality is evident, check that the components of the burner assembly are located properly

If proper operation cannot be obtained, contact your nearest F&P Authorised Service Centre.

The cooktop must not be used by the customer until proper operation has been achieved.

lifting off yellow tip good flame

lifting off yellow tip good flame

500 mm

25 mm

500 mm

25 mm

1

2

1

20-50 mm x 4

NG

NG

½

“ BSP

LPG

LPG

½

“ BSP

Foam Tape

Adhesive side

1

2

OUVERT

!2

RACCORDEZ À L’ALIMENTATION EN GAZ

● ●

Floating nut

Cet appareil est réglé en usine pour utiliser une pression de gaz naturel de

4 po (102 mm) de colonne d’eau ou une pression de gaz de pétrole liquéfié de 11 po (279 mm) de colonne d’eau.

Vérifiez l’étiquette apposée sous l’appareil.

Fibre washer Elbow (½” BSP external thread)

Surface de cuisson

Vers la surface de cuisson

Régulateur de gaz

Pour l’utilisation avec un régulateur de pression de gaz, tel qu’illustré.

!3

20 mm

Le régulateur

50 mm recessed to 50 mm

de circulation du gaz

VÉRIFICATION DES FUITES

Régulateur

Connecteur solide ou flexible

Washer

Arrow

NG

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two semi-rapid burners operating at highest setting.

Washer

LPG

If converting to LPG, see 16 'Converting to a different gas type'

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with the two semi-rapid burners operating at highest setting.

ALL Models

Robinet d’arrêt

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

+50 mm

Tuyau de l’alimentation de la maison

If connecting the gas with a flexible hose:

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 5 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

GAZ

check all connections

● ●

● ●

● ●

● ●

● ●

La vérification des fuites doit être effectuée conformément aux instructions du fabricant.

L’appareil et son robinet d’arrêt individuel doivent être débranchés de la tuyauterie d’alimentation en gaz lorsque la vérification de pression donne une valeur supérieure à 1/2 psi (3,5 kPa).

Fermez manuellement le robinet d’arrêt individuel de l’appareil pour l’isoler de la tuyauterie d’alimentation en gaz pendant toute vérification de pression de la tuyauterie d’alimentation alors que la pression d’essai est égale ou inférieure à 1/2 psi (3,5 kPa).

Pression d’admission maximale de l’alimentation en gaz : 20 po (508 mm) de colonne d’eau (5 kPa)

Pression minimale de l’alimentation en gaz pour la vérification du régulateur de gaz : 5 po (127 mm) de colonne d’eau pour le gaz naturel, 12 po (305 mm) de colonne d’eau pour le gaz de pétrole liquéfié.

OUVERT

7

Une fois l’installation de l’alimentation en gaz et tous les raccordements effectués,

vérifiez soigneusement l’installation pour déceler toute fuite :

1

Tournez tous les boutons de réglage de l’appareil à la position « OFF ».

2

Ouvrez le robinet de l’alimentation en gaz.

3

Check for a well‐defined blue flame without any yellow tipping.

À l’aide d’un fluide de détection de fuite (p. ex. un vaporisateur de détection de fuite Rocol), vérifiez tous les raccords

If proper operation cannot be obtained, contact your nearest F&P Authorised Service Centre.

4 de gaz un à un en vaporisant ou appliquant la solution sur le raccord. La présence de bulles indique une fuite.

Si nécessaire, serrez le raccord et vérifiez de nouveau s’il y a des fuites.

5

Ouvrez la valve de brûleur et allumez chaque brûleur.

The cooktop must not be used by the customer until proper operation has been achieved.

6

Vérifiez si l’appareil produit une flamme bleu clair sans pointe jaune. Si les brûleurs fonctionnent anormalement, yellow tip good flame

500 mm

50 mm

REAR CLAMPS

R

S

A

FRONT CLAMPS

A

S F

Fibre washer

Floating nut

Elbow (½” BSP external thread)

Adhesive side

Foam Tape

1

3⁄8

NPT

2

x 4

PTFE

Floating nut

Fibre washer

Elbow (½” BSP external thread)

2

NG Models

Washer

Arrow

Make sure to fit the supplied washer and regulator.

Adjust to obtain a test point

pressure of 1 kPa with the two semi-rapid burners operating at highest setting.

LPG Models

Washer

Make sure to fit the supplied washer and test point adaptor.

Make sure the supply pressure

is regulated to 2.75 kPa, with the two semi-rapid burners operating at highest setting.

LPG test point adaptor (if using LPG)

x 4

ALL Models

Make sure the connection point will be accessible with the cooktop installed.

To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

!4

APPOSEZ LE DOUBLE DE L’ÉTIQUETTE SIGNALÉTIQUE À UN

!5

INSTALLEZ LES PIÈCES D’APPUI

Ensure the hose is long enough to allow for removal of cooktop for servicing.

Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.

The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.

The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.

Assurez-vous que les pièces d’appui soient positionnées correctement et dans le bon sens (reportez-vous au Guide de l’utilisateur).

The hose must not be kinked, subjected to abrasion or permanently deformed.

The hose must not be near or in contact with any hot surfaces

(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

check all connections

16-20mm

20-30mm 30-40mm

40mm+

Double de l’étiquette signalétique

!6

FAITES UN ESSAI

● ●

● ●

● ●

● ●

● ●

Pour vous assurer que le système d’allumage fonctionne correctement, allumez chaque brûleur individuellement, puis tous les brûleurs simultanément.

Vérifiez si l’appareil produit une flamme bleu clair bien définie, sans pointe jaune.

Si vous constatez un fonctionnement anormal, vérifiez si les composantes de l’assemblage de brûleur sont installées correctement.

S’il est impossible d’obtenir un fonctionnement adéquat, communiquez avec le service à la clientèle ou un centre de service F&P autorisé de votre région.

Le client ne doit pas utiliser la surface de cuisson avant qu’elle ne fonctionne correctement.

éloignement pointe jaune flamme

adéquate

8

500 mm

25 mm

500 mm

25 mm

1

2

1

20-50 mm

x 4

NG

NG

½

“ BSP

LPG

LPG

½

“ BSP

!7

LISTE DE VÉRIFICATION FINALE

À ÊTRE REMPLIE PAR L’INSTALLATEUR

Avez-vous installé les supports de retenue?

Avez-vous vérifié si le type de modèle (réglé en usine pour le gaz naturel (GN) ou le gaz de pétrole liquéfié (GPL)) correspond au type de gaz disponible sur le site d’installation?

Avez-vous utilisé la rondelle en fibre fournie?

Avez-vous vérifié tous les raccords pour déceler d’éventuelles fuites?

La surface de cuisson est-elle réglée à la pression adéquate?

Avez-vous apposé le double de l’étiquette signalétique fourni sur une surface adjacente accessible au client?

La surface de cuisson est-elle mise à la terre?

Assurez-vous que le câble d’alimentation électrique ne touche PAS à la surface de cuisson.

FONCTIONNEMENT :

Est-ce que tous les brûleurs peuvent s’allumer individuellement et simultanément?

Les flammes sont-elles uniformes et de la bonne taille?

Avez-vous expliqué le fonctionnement de base au client?

9

Compléter et conserver pour référence sûre:

Modèle

N ° De Série

Purchase Date

Date D’achat

Adresse Du Revendeur

Nom De L’installateur

Signature De L’installateur

Société D’installation

Date D’installation

10

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement