UL Listed Hi-lume A-Series Constant Voltage Driver Overview

UL Listed Hi-lume A-Series Constant Voltage Driver Overview
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 1 01.07.14
UL Listed Hi-lume® A-Series
Constant Voltage Driver Overview
The UL Listed Hi-lume® A-Series Constant Voltage
Driver is a high‑performance LED driver that provides
smooth, continuous 1% dimming for 12 V- and
24 V- constant voltage LED sources up to 40 W.
The UL listing ensures a safe and reliable installation
because the driver is pre-packaged with its own
specialized wiring and mounting enclosure.
Features
•UL Listed for the United States and Canada
•Continuous, flicker-free dimming from 100% to 1%
•4 in (102 mm) square, metal junction box included to
provide a UL Listed wiring compartment
•Guaranteed compatibility with these Lutron® systems:
–All EcoSystem® compatible products
–GRAFIK SystemsTM
–HomeWorks® QS
–Maestro Wireless®
–Quantum®
–RadioRA® 2
–Lutron® wallbox 3-Wire fluorescent controls and
interfaces
–Select wallbox products
–Select C•L® products
For a complete list of controls, see charts in the
Wiring section:
–LTE models (pages 5 – 7)
–L3D models (pages 8 – 10)
Note: L3D models for commercial spaces only.
•LED Load Replacement. Because these are Class 2
rated drivers, the LED load can be changed while the
driver is installed and powered.
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Hi-lume® A-Series Driver Model LTEA4U1UKL-AV120
•100% performance-tested at factory
•Protected from miswires of input power to
EcoSystem® control inputs
•A rated lifetime of 50,000 hours @ tc = 65 °C
•FCC Part 15 compliant for commercial and residential
applications at 120 V~ (LTE models only)
•FCC Part 15 compliant for commercial applications at
120 V~ and 277 V~ (L3D models only)
•RoHS Compliant
•For more information please go to:
www.lutron.com/HilumeLED
Page
1
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 2 01.07.14
Specifications
Performance
Regulatory Approvals
•Dimming Range: 100% to 1% (measured light output)
•Operating Voltage
–LTE models: 120 V~ at 50/60 Hz
–L3D models: 120 – 277 V~ at 50/60 Hz (for
commercial space only)
•Output: 12 V- and 24 V- constant voltage
Note: Not intended for use with MR-16 lamps
• Output: 5 – 40 W
•A rated lifetime of 50,000 hours @ tc = 65 °C
– For rated warranty, tc not to exceed the maximum
rated temperatures.1
•Patented thermal foldback protection
•LEDs turn on to any dimmed level without going to
full brightness
•Nonvolatile memory restores all driver settings after
power failure
•Power Factor: > 0.90 for loads greater than 20 W
•Total Harmonic Distortion (THD): < 20% for loads
greater than 20 W
•Inrush Current: < 2 A
•Inrush Current Limiting Circuitry: eliminates circuit
breaker tripping, switch arcing and relay failure
•Output is open-circuit protected
•Output is short-circuit protected
•Turn-on time2: ≤ 1.5 second
•PWM Dimming Frequency: 550 Hz
Environmental
•Sound Rating: Inaudible in 27 dB ambient
•Relative Humidity: Maximum 90% non-condensing
•Operating ambient temperature
ta = 32 – 104 °F (0 – 40 °C)
•Meets ANSI C62.41 category A surge protection
standards up to and including 4 kV
•FCC Part 15 compliant for commercial and residential
applications at 120 V~ (LTE models only)
•FCC Part 15 compliant for commercial applications at
120 V~ and 277 V~ (L3D models only)
•Manufacturing facilities employ ESD reduction
practices that comply with the requirements of
ANSI/ESD S20.20
•Lutron® Quality Systems registered to ISO 9001.2008
•UL 8750-listed
•Class 2 output
Driver Wiring and Mounting
•Driver is grounded by green ground wire connection
on the enclosure or by ground lug terminal in the
junction box
•Driver and junction box must be grounded in
accordance with local and national electrical codes
•All wire connections must be made in the junction box
to maintain UL listing
•4 in (102 mm) square junction box is 1.5 in (38 mm)
deep with a 22.0 cubic in (360.5 cubic cm) capacity
and complies with NEMA® OS 1-2008 Figure 112
•Driver is pre-wired with 6 in (152 mm), 18 AWG
(0.75 mm2) solid copper leads in all terminal blocks
•For 277~ V applications, a suitable barrier should be
installed between the input and Class 2 wiring inside
the junction box per local and national electrical
wiring codes
•Maximum driver-to-LED light engine wire length for
Constant Voltage Drivers:
Maximum Lead Length
12 V24 V18 AWG (0.75 mm2) 10 ft (3 m) 15 ft (4.5 m)
16 AWG (1.5 mm2) 15 ft (4.5 m) 25 ft (7.5 m)
14 AWG (2.5 mm2) 25 ft (7.5 m) 40 ft (12 m)
12 AWG (4.0 mm2) 40 ft (12 m) 60 ft (18 m)
Wire Gauge
1
Installer is responsible for ensuring that the driver case temperature does not exceed the maximum rated temperature.
2
Models available with turn-on times ≤ 1 second.
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
2
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 3 01.07.14
Models Available
Model
For 24 VConstant Voltage LTE A4U1UKL-CV240
LED Loads
2-Wire
Forward Phase
For 12 VControl2
Constant Voltage LTE A4U1UKL-AV120
LED Loads
3-Wire or
EcoSystem®
Control3,4
For 24 VConstant Voltage L3D A4U1UKL-CV240
LED Loads
For 12 VConstant Voltage L3D A4U1UKL-AV120
LED Loads
Input
Input
Output Output
Voltage Current Power
Voltage
1
Factor Power
(V~)
(mA)
(W)
(V-)
120
380
0.99
5 – 40
24.0
120
400
0.98
5 – 40
12.0
120
370
0.99
5 – 40
24.0
277
170
0.96
5 – 40
24.0
120
390
0.99
5 – 40
12.0
277
170
0.95
5 – 40
12.0
Note: for OEMs: Other constant current and constant voltage models available; refer to Hi-lume® A-Series LED Driver Specification
Submittals for more details: Lutron® P/N 369325 and P/N 369543.
Note: Lutron® LED drivers are not intended for use with with MR-16 lamps.
1
At maximum output power.
For wiring options, see Wiring section, pages 5 – 7.
3 For wiring options, see Wiring section, pages 8 – 10.
4 For commercial application only.
2
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
3
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 4 01.07.14
KL Enclosure Dimensions
Measurements are shown as: in (mm)
4.89 (124)
2.62 (66)
1.62 (41)
4.00 (102)
4.00 (102)
KL enclosure includes a 4 in (102 mm) square junction box
which complies with NEMA® OS 1-2008 Figure 112.
Knockouts
•Sides
–8 locations: 0.5 in (13 mm)
–4 locations: 0.5/0.75 in (13/19 mm)
•Bottom
–2 locations: 0.5 in (13 mm)
–2 locations: 0.5/0.75 in (13/19 mm)
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
4
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 5 01.07.14
Wiring
LTE 2-Wire Forward Phase Models: Controls Requiring Neutral
Note: Driver is pre-wired with 6 in (152 mm) solid copper leads of 18 AWG (0.75 mm2) in all terminal blocks.
Colors shown correspond to wires on driver.
Wiring Diagram
Lutron®
Neutral-Wire
Dimmer
Line
Neutral
Ground1
Neutral
+V (Red)2
Dimmed Line (Black)
Hi-lume ®
A-Series LED
Dimming Driver
Neutral (White)
LED
Light
Engine
–V (Black/White)2
Ground (Green)1
Ground1
1
Enclosure and junction box must be grounded in accordance with local and national electrical codes. Ground provided by grounding of junction box or by
using the green ground wire connection.
2 For maximum driver-to-LED light engine wire length, see charts in Driver Wiring and Mounting section.
Compatible Controls: Lutron® Neutral-Wire Wallbox Dimmers
Guaranteed performance specifications with the controls listed in the chart below.
For assistance selecting controls, contact our LED Center of Excellence at 1.877.346.5338 or [email protected]
A
Product
Part Number
Low-End Setting/Load-Type Setting*
A: Not Ganged
B
B
B
C
B
Drivers per Control
B: End of Gang C: Middle of Gang
Maestro Wireless®
MRF2-6ND-120
dimmer
Trim low-end per Advanced
Programming Mode App Note
(Lutron® P/N 048370)
1 – 8
1 – 8
1 – 8
HomeWorks® QS
adaptive dimmer
HomeWorks® QS
600 W dimmer
HomeWorks® QS
1000 W dimmer
HQRD-6NA-
LED Lutron® A-Series 2-Wire
1 – 8
1 – 8
1 – 8
HQRD-6ND-
LED Lutron® A-Series 2-Wire
1 – 8
1 – 8
1 – 8
HQRD-10ND-
LED Lutron® A-Series 2-Wire
1 – 13
1 – 13
1 – 13
RadioRA® 2
adaptive dimmer
RRD-6NA-
Hi-lume® A-Series LTE LED Driver
2-Wire
1 – 8
1 – 8
1 – 8
RadioRA® 2
1000 W dimmer
RRD-10ND-
Set Device type to “INC/MLV Neutral
Dimmer”; Set High-End Trim to 99%;
Set Low-End Trim to 35%
1 – 13
1 – 13
1 – 13
* Setting the low-end trim and load type is necessary to ensure optimal performance and 1% dimming capability.
Note: For information about Legacy Product use in existing control application, contact [email protected]
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
5
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 6 01.07.14
Wiring (continued)
LTE 2-Wire Forward Phase Models: Controls Requiring Neutral (continued)
Note: Driver is pre-wired with 6 in (152 mm) solid copper leads of 18 AWG (0.75 mm2) in all terminal blocks.
Colors shown correspond to wires on driver.
Wiring Diagram
Lutron®
Dimming
Module/Panel
Line
Neutral
Hi-lume ®
A-Series LED
Dimming Driver
Ground1
Neutral
+V (Red)2
Dimmed Line (Black)
Neutral (White)
LED
Light
Engine
–V (Black/White)2
Ground (Green)1
Ground1
1
Enclosure and junction box must be grounded in accordance with local and national electrical codes. Ground provided by grounding of junction box or by
using the green ground wire connection.
2 For maximum driver-to-LED light engine wire length, see charts in Driver Wiring and Mounting section.
Compatible Controls: Lutron® Dimming Modules/Panels
Guaranteed performance specifications with the controls listed in the chart below.
For assistance selecting controls, contact our LED Center of Excellence at 1.877.346.5338 or [email protected]
Product
Part Number
HomeWorks® QS wallbox power module
HQRJ-WPM-6D-120
HomeWorks® wallbox power module
HWI-WPM-6D-120
QSGR-,
QSGRJGRX-3100-,
GRAFIK Eye® 3000 control unit
GRX-3500RPM-4U module (LCP, HomeWorks® QS, HW-RPM-4U-120,
GRAFIK SystemsTM, Quantum®)
LP-RPM-4U-120
GRAFIK Eye® QS control unit
RPM-4A module (LCP, HomeWorks® QS, HW-RPM-4A-120,
GRAFIK SystemsTM, Quantum®)
LP-RPM-4A-120
GP dimming panels
Various
Drivers per Control Low-End Setting/Load-Type Setting*
1 – 10 (per output);
26 total per module
1 – 10 (per output);
26 total per module
1 – 10 (per output);
26 total per unit
1 – 10 (per output);
26 total per unit
1 – 26 (per output);
26 total per module
LED Lutron® A-Series 2-Wire
Set load type to “GRX-FDBI or GRX-TVI”
Set load type to “Fluorescent Module”
Set load type to “GRX‑FDBI or GRX-TVI”
LED Lutron® A-Series 2-Wire
Set load type to “2-1”
1 – 13 (per output);
LED Lutron® A-Series 2-Wire
26 total per module Set load type to “2-1”
1 – 26
Set load type to “2-1”
* Setting the low-end trim and load type is necessary to ensure optimal performance and 1% dimming capability.
Note: For information about Legacy Product use in existing control application, contact [email protected]
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
6
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 7 01.07.14
Wiring (continued)
Controls Not Requiring Neutral
LTE 2-Wire Forward Phase Models: Controls Not Requiring Neutral
Note: Driver is pre-wired with 6 in (152 mm) solid copper leads of 18 AWG (0.75 mm2) in all terminal blocks.
Colors shown correspond to wires on driver.
Wiring Diagram
Line
LutronR
Non-Neutral
Forward
Phase
Dimmer
Ground1
Neutral
+V (Red)2
Dimmed Line (Black)
Hi-lume ®
A-Series LED
Dimming Driver
Neutral (White)
LED
Light
Engine
–V (Black/White)2
Ground (Green)1
Ground1
1
Enclosure and junction box must be grounded in accordance with local and national electrical codes. Ground provided by grounding of junction box or
by using the green ground wire connection.
2 For maximum driver-to-LED light engine wire length, see charts in Driver Wiring and Mounting section.
Compatible Controls: Lutron® Non-Neutral Wallbox Dimmers
Guaranteed performance specifications with the controls listed
in the chart below.
For assistance selecting controls, contact our LED Center of Excellence
at 1.877.346.5338 or [email protected]
Product
Part Number
Low-End Setting/Load-Type Setting*
A
A: Not Ganged
B
B
B
C
Drivers per Control
B: End of Gang C: Middle of Gang
Set low-end trim dial to 1 o’clock.
Adjust slightly if needed. See Figure 1
under ‘Dimmer Range Adjustment’
section in the Dimmer Installation
Guide for how to adjust low-end trim.
1 – 8
1 – 8
1 – 8
Set low-end trim dial to 10 o’clock.
Adjust slightly if needed. See Figure 1
Diva® C•L® 250 W
under ‘Dimmer Range Adjustment’
dimmer
section in the Dimmer Installation
DVSCCL-253P- Instructions for how to adjust low-end
trim.
1 – 8
1 – 8
1 – 8
GRAFIK TTM, C•L® GT-250Mor RF C•L®
dimmer
GTJ-250M-
1 – 8
1 – 8
1 – 8
Ariadni® C•L® 250
AYCL-253PW dimmer
B
DVCL-253P-
Set low-end trim per Dimmer
Installation Instructions.
* Setting the low-end trim and load type is necessary to ensure optimal performance and 1% dimming capability.
Note: For information about Legacy Product use in existing control application, contact [email protected]
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
7
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 8 01.07.14
Wiring (continued)
L3D Models: 3-Wire Controls (Third wire required for control signal)
Note: Driver is pre-wired with 6 in (152 mm) solid copper leads of 18 AWG (0.75 mm2) in all terminal blocks.
Colors shown correspond to wires on driver.
Wiring Diagram
E1 (Purple)1
Lutron®
3-Wire
Dimmer
Line
E2 (Purple)1
Dimmed Line (Orange)2
Neutral
Ground3
Neutral
+V (Red)4
Switched Line (Black)2
Hi-lume ®
A-Series LED
Dimming Driver
Neutral (White)2
LED
Light
Engine
–V (Black/White)4
Ground (Green)3
Ground3
1
Purple wires must be capped off separately if dimmed hot (orange) is being used.
For 277 V~ applications, a suitable barrier should be installed between the input and Class 2 wiring inside the junction box per local and national
electrical wiring codes.
3 Enclosure and junction box must be grounded in accordance with local and national electrical codes. Ground provided by grounding of junction box or by
using the green ground wire connection.
4 For maximum driver-to-LED light engine wire length, see charts in Driver Wiring and Mounting section.
2
Compatible Controls: Lutron® 3-Wire Wallbox Dimmers
Guaranteed performance specifications with the controls listed in the chart below.
For assistance selecting controls, contact our LED Center of Excellence at 1.877.346.5338 or [email protected]
Part Number
Drivers per Control*
120 V~
277 V~
120 V~
277 V~
1 – 41
1 – 44
NTF-10NTF-10-277Nova T*® dimmer
NTF-103PNTF-103P-2771 – 20
1 – 33
1 – 41
1 – 44
NF-10NF-10-277Nova® dimmer
NF-103PNF-103P-2771 – 20
1 – 33
1 – 20
1 – 33
SF-10PSF-12P-277Skylark® dimmer
SF-103PSF-12P-277-31 – 20
1 – 33
1 – 20
1 – 33
DVF-103PDVF-103P-277Diva® dimmer
DVSCF-103P- DVSCF-103P-2771 – 20
1 – 33
Lyneo® Lx dimmer LXF-103PLLXF-103PL-2771 – 20
1 – 20
Ariadni® dimmer
AYF-103PAYF-103P-2771 – 20
1 – 44
Product
* No derating required in multi-gang applications provided that driver count does not exceed quantity listed.
Note: For information about Legacy Product use in existing control application, contact [email protected]
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
8
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 9 01.07.14
Wiring (continued)
L3D Models: 3-Wire Controls (Third wire required for control signal) (continued)
Note: Driver is pre-wired with 6 in (152 mm) solid copper leads of 18 AWG (0.75 mm2) in all terminal blocks.
Colors shown correspond to wires on driver.
Wiring Diagram
E1 (Purple)1
Lutron®
3-Wire
Dimmer/
Module/Panel
Line
E2 (Purple)1
Dimmed Line (Orange)2
Neutral
Ground3
Neutral
+V (Red)4
Switched Line (Black)2
Hi-lume ®
A-Series LED
Dimming Driver
Neutral (White)2
LED
Light
Engine
–V (Black/White)4
Ground (Green)3
Ground3
1
Purple wires must be capped off separately if dimmed hot (orange) is being used.
For 277 V~ applications, a suitable barrier should be installed between the input and Class 2 wiring inside the junction box per local and national
electrical wiring codes.
3 Enclosure and junction box must be grounded in accordance with local and national electrical codes. Ground provided by grounding of junction box or by
using the green ground wire connection.
4 For maximum driver-to-LED light engine wire length, see charts in Driver Wiring and Mounting section.
2
Compatible Controls: Lutron® 3-Wire Wallbox Dimmers, Modules, and Panels
Guaranteed performance specifications with the controls listed in the chart below.
For assistance selecting controls, contact our LED Center of Excellence at 1.877.346.5338 or [email protected]
Part Number
120 V~
277 V~
Product
Vierti® dimmer
VTF-6AMAF-6AMMAF-6AM-277Maestro® dimmer
MSCF-6AMMSCF-6AM-277Maestro Wireless® dimmer
MRF2-F6AN-DVRadioRA® 2 dimmer
RRD-F6AN-DVHomeWorks® QS dimmer
HQRD-F6AN-DVPHPM-3F-120—
Interfaces2
PHPM-3F-DVGP dimming panels
Various
1
2
Drivers per Control1
120 V~
277 V~
1 – 15
1 – 15
1 – 15
1 – 15
1 – 15
1 – 15
1 – 41
1 – 41
1 – 41
1 – 33
1 – 33
1 – 33
1 – 33
1 – 33
1 – 33
–
1 – 88
1 – 88
No derating required in multi-gang applications provided that fixture-count does not exceed quantity listed.
For use with 3-Wire controls, Commercial Systems applications, RadioRA ® 2 Systems, or other Home Systems applications.
Note: For information about Legacy Product use in existing control application, contact [email protected]
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
9
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 10 01.07.14
Wiring (continued)
L3D Models: EcoSystem® Digital Controls
Note: Driver is pre-wired with 6 in (152 mm) solid copper leads of 18 AWG (0.75 mm2) in all terminal blocks.
Colors shown correspond to wires on driver.
Wiring Diagram
E1 (Purple)
To EcoSystem® Digital Link
E2 (Purple)
+V (Red)4
Line (Black)1
Dimmed Line (Orange)1,2
Hi-lume ®
A-Series LED
Dimming Driver
LED
Light
Engine
Neutral (White)1
–V (Black/White)4
Ground (Green)3
Ground3
1
For 277 V~ control applications, the 277~ V wiring and Class 2 wiring should be separated by a barrier in accordance with local and national electric
codes.
2 Dimmed hot (orange) wire must be capped off separately if EcoSystem ® control is used.
3 Enclosure must be grounded in accordance with local and national electrical codes. Ground provided by grounding of junction box or by using the green
ground wire connection.
4 For maximum driver-to-LED light engine wire length, see charts in Driver Wiring and Mounting section.
Compatible Controls: Lutron® EcoSystem® Digital Controls
Guaranteed performance specifications with the controls listed in the chart below.
For assistance selecting controls, contact our LED Center of Excellence at 1.877.346.5338 or [email protected]
Product
PowPak® Dimming Module with EcoSystem®
Energi Savr Node TM unit with EcoSystem®
GRAFIK Eye® QS unit with EcoSystem®
Quantum® Light Management Hub
HomeWorks® QS DIN Rail Power Module with EcoSystem®
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Part Number
120 V~
277 V~
RMJ-ECO32-DV-B
QSN-1ECO-S,
QSN-2ECO-S
QSGRJ—
QSGRQP2QP3—
QP4LQSE-2ECO-D
—
Drivers per Control
32 per EcoSystem® link
64 per EcoSystem® link
64 per EcoSystem® link
64 per EcoSystem® link
64 per EcoSystem® link
Page
10
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 11 01.07.14
EcoSystem® Digital Link
(L3D Models only)
GND
NEU
DH
SH
E2
E1
Digital
Bus
•Driver EcoSystem® Digital Link terminals accept only
one 18 to 16 AWG (0.75 to 1.5 mm2) solid copper wire
per terminal
•Make sure that the supply breaker to the Digital Driver
and EcoSystem® Digital Link Supply is OFF when
wiring
•Connect the two conductors to the two Digital Driver
terminals E1 and E2 as shown
•Using two different colors for E1 and E2 will reduce
confusion when wiring several drivers together
•The EcoSystem® Digital Link may be wired Class 1 or
Class 2. Consult applicable electrical codes for proper
wiring practices
Driver Terminals
Line
Wiring
E2
E1
Digital
Bus
•The EcoSystem® Digital Link wiring (E1 and E2)
connects digital ballasts and drivers together to form a
lighting control system
•Each EcoSystem® Digital Link supports up to 64 digital
ballasts, LED drivers or EcoSystem® Modules
(e.g., C5-BMJ-16A, C5-XPJ-16A), 32 occupancy
sensors (64 occupancy sensors with Energi Savr
NodeTM with EcoSystem®), 16 daylight sensors, and
64 wallstations or IR receivers*
•Sensors do not directly connect to Hi-lume® A-Series
LED drivers
•E1 and E2 (EcoSystem® digital link wires) are
polarity‑insensitive and can be wired in any topology
•An Energi Savr NodeTM unit with EcoSystem®, GRAFIK
Eye® QS control unit with EcoSystem®, PowPak®
dimming module with EcoSystem®, or Quantum®
system provides power for the EcoSystem® Digital
Link and supports system programming*
•All EcoSystem® Digital Link programming is completed
by using the Energi Savr App for Apple iPad, iPod
Touch, or iPhone mobile digital devices, GRAFIK Eye®
QS with EcoSystem® control unit, PowPak® dimming
module with EcoSystem®, or Quantum® system
Line
GND
NEU
DH
SH
Overview
Driver Terminals
To the EcoSystem® Digital Bus and
additional drivers and/or ballasts
Notes
•The EcoSystem® Digital Link Supply does not have to
be located at the end of the Digital Link
•EcoSystem® Digital Link length is limited by the wire
gauge used for E1 and E2 as follows:
Wire Gauge
12 AWG
14 AWG
16 AWG
18 AWG
Digital Link Length (max)
2200 ft
1400 ft
900 ft
550 ft
Wire Size
4.0 mm2
2.5 mm2
1.5 mm2
1.0 mm2
0.75 mm2
Digital Link Length (max)
825 m
515 m
310 m
205 m
155 m
*PowPak® dimming module with EcoSystem® provides power for the EcoSystem® Digital Link and can support 32 digital ballasts, LED drivers, or
EcoSystem® modules, 6 wireless occupancy sensors, 1 wireless daylight sensor, and 9 Pico® wireless controllers.
Apple, iPad, iPod Touch, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
11
LED Dimming Driver
Hi-lume® A-Series Constant Voltage Driver (UL Listed)
Architectural Dimming
369789c 12 01.07.14
Electricians and Contractors
Facilities Managers
Driver Leads
Service
Maximum driver-to-LED light engine wire length for
Constant Voltage Drivers:
Maximum Lead Length
12 V24 V18 AWG (0.75 mm2) 10 ft (3 m) 15 ft (4.5 m)
16 AWG (1.5 mm2) 15 ft (4.5 m) 25 ft (7.5 m)
14 AWG (2.5 mm2) 25 ft (7.5 m) 40 ft (12 m)
12 AWG (4.0 mm2) 40 ft (12 m) 60 ft (18 m)
Wire Gauge
Wiring and Grounding
Driver and junction box must be grounded.
Drivers and junction box must be installed per national
and local electrical codes.
Warranty
For warranty information, please visit
http://www.lutron.com/BallastDriverWarranty
Replacement Parts
When ordering Lutron® replacement parts, please
provide the full model number. Consult Lutron
Technical Support if you have any questions.
Further Information
For further information, please visit us at
www.lutron.com/hilumeLED or contact our
LED Control Center of Excellence at 1.877.346.5338
or [email protected]
LED Load Replacement
Because these are Class 2 rated drivers, the LED load
can be changed while the driver is installed and
powered.
Maximum Driver Operating Temperature
Driver case temperature (tc) must not exceed UL
conditions of acceptability in end product.
For 50,000 hour lifetime, driver case temperature (tc)
must not exceed 65 °C.
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement