advertisement
Owner's Manual
Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p.2),
"USING THE UNIT SAFELY" (p. 3), and "IMPORTANT NOTES" (p. 5). These sections provide important
information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.
Copyright © 2012 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
* Roland is either registered trademark or trademark of Roland Corporation in the United States and/or other countries.
* All product names mentioned in this document are trademarks or registered trademarks of their respective owners.
2
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with a dry cloth.
7.
Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
For the U.K.
WARNING:
IMPORTANT:
THIS APPARATUS MUST BE EARTHED
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
USING THE UNIT SAFELY
001-50
Make sure that the power cord is grounded.
• Connect mains plug of this model to a mains socket outlet with a protective earthing connection.
.................................................................................................................................................
002a
Do not disassemble or modify by yourself.
• Do not open or perform any internal modifications on the unit.
.................................................................................................................................................
003
Do not repair or replace parts by yourself.
• Do not attempt to repair the unit, or replace parts within it
(except when this manual provides specific instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” sheet.
.................................................................................................................................................
004
Do not use or store in the following types of locations.
• Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heatgenerating equipment); or are
• Damp (e.g., baths, washrooms, on wet floors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Humid; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and shakiness.
.................................................................................................................................................
006a
Do not place in an unsuitable location.
• When using the unit with a rack or stand recommended by
Roland, the rack or stand must be carefully placed so it is level and sure to remain stable. If not using a rack or stand, you still need to make sure that any location you choose for placing the unit provides a level surface that will properly support the unit, and keep it from wobbling.
.................................................................................................................................................
008e
Use only the included power cord.
• Use only the attached power-supply cord. Also, the supplied power cord must not be used with any other device.
................................................................................................................................................
008f
Connect the power cord to an outlet of the correct voltage.
• The unit should be connected to a power supply only of the type described in the operating instructions, or as marked on the side panel of unit.
................................................................................................................................................
009
Do not bend the power cord or place heavy objects on it.
• Do not excessively twist or bend the power cord, nor place heavy objects on it. Doing so can damage the cord, producing severed elements and short circuits. Damaged cords are fire and shock hazards!
................................................................................................................................................
011
Don’t allow foreign objects or liquid to enter unit ; never place containers with liquid on unit.
• Do not place containers containing liquid on this product.
Never allow foreign objects (e.g., flammable objects, coins, wires) or liquids (e.g., water or juice) to enter this product.
Doing so may cause short circuits, faulty operation, or other malfunctions.
................................................................................................................................................
012a
Turn off the unit if an abnormality or malfunction occurs.
• Immediately turn the unit off, remove the power cord from the outlet, and request servicing by your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” sheet when:
• The power-supply cord or the plug has been damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been spilled onto the unit; or
• The unit has been exposed to rain (or otherwise has become wet); or
• The unit does not appear to operate normally or exhibits a marked change in performance.
................................................................................................................................................
3
USING THE UNIT SAFELY
013
Adults must provide supervision in places where children are present.
• When using the unit in locations where children are present, be careful so no mishandling of the unit can take place. An adult should always be on hand to provide supervision and guidance.
.................................................................................................................................................
014
Do not drop or subject to strong impact
• Protect the unit from strong impact. (Do not drop it!)
.................................................................................................................................................
015
Do not share an outlet with an unreasonable number of devices.
• Do not force the unit’s power-supply cord to share an outlet with an unreasonable number of other devices. Be especially careful when using extension cords - the total power used by all devices you have connected to the extension cord’s outlet must never exceed the power rating (watts/amperes) for the extension cord. Excessive loads can cause the insulation on the cord to heat up and eventually melt through.
.................................................................................................................................................
016
Do not use overseas.
• Before using the unit in a foreign country, consult with your retailer, the nearest Roland Service Center, or an authorized
Roland distributor, as listed on the “Information” sheet.
.................................................................................................................................................
101a
Place in a well ventilated location.
• The unit should be located so that its location or position does not interfere with its proper ventilation.
.................................................................................................................................................
102b
Grasp the plug when connecting or disconnecting the power cord.
• Always grasp only the plug on the power-supply cord when plugging into, or unplugging from, an outlet or this unit.
.................................................................................................................................................
103a
Periodically clean the power cord’s plug.
• At regular intervals, you should unplug the power plug and clean it by using a dry cloth to wipe all dust and other accumulations away from its prongs. Also, disconnect the power plug from the power outlet whenever the unit is to remain unused for an extended period of time. Any accumulation of dust between the power plug and the power outlet can result in poor insulation and lead to fire.
.................................................................................................................................................
104
Manage cables for safety.
• Try to prevent cords and cables from becoming entangled.
Also, all cords and cables should be placed so they are out of the reach of children.
.................................................................................................................................................
106
Avoid climbing on top of the unit, or placing heavy objects on it.
• Never climb on top of, nor place heavy objects on the unit.
.................................................................................................................................................
107b
Do not connect or disconnect the power cord with wet hands.
• Never handle the power cord or its plugs with wet hands when plugging into, or unplugging from, an outlet or this unit.
.................................................................................................................................................
108a
Disconnect everything before moving the unit.
• Before moving the unit, disconnect the power plug from the outlet, and pull out all cords from external devices.
.................................................................................................................................................
109a
Unplug the power cord from the outlet before cleaning.
• Before cleaning the unit, turn it off
power cord from the outlet.
.................................................................................................................................................
110a
If there is a possibility of lightning strike, disconnect the power cord from the outlet.
• Whenever you suspect the possibility of lightning in your area, pull the plug on the power cord out of the outlet.
.................................................................................................................................................
118d
Keep small items out of the reach of children
• To prevent accidental ingestion of the parts listed below, always keep them out of the reach of small children.
• Removable Parts
Screws for rack mount angles (p. 53)
.................................................................................................................................................
118e
Handle the ground terminal carefully.
• If you remove the screw from the ground terminal, be sure to replace it; don't leave it lying around where it could accidently be swallowed by small children. When refastening the screw, make that it is firmly fastened, so it won't come loose.
.................................................................................................................................................
119
Take care not to be burned.
• The rear panel of this unit may become hot, so take care to avoid burns.
..................................................................................................................................................
4
IMPORTANT NOTES
Power Supply
301
• Do not connect this unit to same electrical outlet that is being used by an electrical appliance that is controlled by an inverter or a motor (such as a refrigerator, washing machine, microwave oven, or air conditioner).
Depending on the way in which the electrical appliance is used, power supply noise may cause this unit to malfunction or may produce audible noise. If it is not practical to use a separate electrical outlet, connect a power supply noise filter between this unit and the electrical outlet.
307
• To prevent malfunction and equipment failure, always make sure to turn off the power on all your equipment before you make any connections.
308
• Although the LCD and LEDs are switched off when the unit is turned off, this does not mean that the unit has been completely disconnected from the source of power. If you need to turn off the power completely, first turn off the unit’s switch, then unplug the power cord from the power outlet. For this reason, the outlet into which you choose to connect the power cord’s plug should be one that is within easy reach and readily accessible.
Placement
352a
• This device may interfere with radio and television reception. Do not use this device in the vicinity of such receivers.
352b
• Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off.
354a
• Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit.
355b
• When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the unit. Damage or malfunction may result if you attempt to use the unit in this condition. Therefore, before using the unit, you must allow it to stand for several hours, until the condensation has completely evaporated.
360
• Depending on the material and temperature of the surface on which you place the unit, its rubber feet may discolor or mar the surface. You can place a piece of felt or cloth under the rubber feet to prevent this from happening. If you do so, please make sure that the unit will not slip or move accidentally.
361
• Do not put anything that contains water on this unit. Also, avoid the use of insecticides, perfumes, alcohol, nail polish, spray cans, etc., near the unit. Swiftly wipe away any liquid that spills on the unit using a dry, soft cloth.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.
Additional Precautions
poke-mon
• This unit allows you to switch images or turn video effects on/off at high speed. For some people, viewing such images can cause headache, nausea, or other discomfort. Do not use this unit to create video that might cause these types of health problems. Roland Corporation will accept no responsibility for any such health problems that may occur in yourself or in viewers.
552
• Unfortunately, it may be impossible to restore the contents of data that was stored in the unit’s memory or USB memory once it has been lost.
Roland Corporation assumes no liability concerning such loss of data.
553
• Use a reasonable amount of care when using the unit’s buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions.
556
• When disconnecting all cables, grasp the connector itself - never pull on the cable. This way you will avoid causing shorts, or damage to the cable’s internal elements.
557
• A small amount of heat will radiate from the unit during normal operation.
559a
• When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you will need to use equivalent packaging materials.
Before Using USB Memories
704
• Carefully insert the USB memory all the way in---until it is firmly in place.
705
• Never touch the terminals of the USB memory. Also, avoid getting the terminals dirty.
708
• USB memories are constructed using precision components; handle the memories carefully, paying particular note to the following.
• To prevent damage to the cards from static electricity, be sure to discharge any static electricity from your own body before handling the cards.
• Do not touch or allow metal to come into contact with the contact portion of the cards.
• Do not bend, drop, or subject cards to strong shock or vibration.
• Do not keep cards in direct sunlight, in closed vehicles, or other such locations.
• Do not allow cards to become wet.
• Do not disassemble or modify the cards.
Others
988
• Security Slot ( ) http://www.kensington.com/ class A
• This product is a Class A digital device under FCC part 15 for use in other than residential environment. Use of this equipment in a residential environment may cause radio interference requiring the user to take appropriate preventative measures. In such instances, take steps such as using cables with ferrite cores near their connectors. For information on specific preventive methods, contact your dealer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the "Information" sheet.
Class A
• When this device is connected to a video cameras or other such Class B equipment, the system as a whole is then classified as a Class A device.
• Recording, duplication, distribution, sale, lease, performance, or broadcast of copyrighted material (musical works, visual works, broadcasts, liver performances, etc.) belonging to a third party in part or in whole without the permissions of copyright owner is forbidden by law.
• Do not use this product for purposes that could infringe on a copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of third-party copyrights arising through your use of this product.
5
6
Contents
Connecting External Equipment ................................................................ 19
V-800HD Version 1.50 Added Functions................................................... 56
7
Check the Included Items
The following items are included. Please make sure that all items are present. If anything is missing, please contact your dealer.
V-800HD itself
fig.V800HD-itself.eps
Owner’s manual (this document)
fig.owners-manual.eps
Power cord
fig.power-cord.eps
Rack mount angle (two)
fig.rack-angle.eps
* For fitting of rack mount angles, refer to "About Rack Mount
Input Template
fig.input-template.eps
* Refer to "About the Input Template" (p. 53).
8
The explanations in this manual include illustrations that depict what should typically be shown by the display. Note, however, that your unit may incorporate a newer, enhanced version of the system, so what you actually see in the display may not always match what appears in the manual.
MMP (Moore Microprocessor Portfolio) refers to a patent portfolio concerned with microprocessor architecture, which was developed by Technology Properties Limited (TPL). Roland has licensed this technology from the TPL Group.
About the Multi-view Monitor
Connecting the Monitor
To operate the V-800HD, a monitor must be connected. Connect a monitor that supports HDMI input to the connector shown below.
fig.connect-monitor.eps
HDMI
Selecting an Output Format for the Multi-view Monitor
You can select an output format for the monitor connected to the V-800HD. Depending on the monitor you are using, select one from below.
Output Y/Cb/Cr signal
Hold down [1] of the MEMORY buttons and turn the power on.
fig.HDMI-out.eps
+
Output RGB signal
Hold down [2] of the MEMORY buttons and turn the power on.
* Select RGB output when you are connecting a monitor using a HDMI - DVI conversion cable or the like.
fig.RGB-out.eps
+
Once you select, the setup is kept and valid from the next booting. While booting, [1] or [2] of the MEMORY will light up in red and enables you to check your setup.
About the Menu Displays
Pressing the [MENU] button on the top panel displays the menu. To make the menu disappear, press the [EXIT] or [MENU] button on the top panel.
fig.menu-display.eps
Setup Menu
Input
Output
Transition
PinP
Key
DSK
System
PVW
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
PGM
CH 1 CH 2 CH 3 CH 4
CH 5 CH 6 CH 7 CH 8
the following Roland website.
http://www.rolandsystemsgroup.net/
9
About the Multi-view Monitor
About the Display on the Multi-view Monitor
When the source device is connected to the V-800HD and turned on, the output video and the source video are displayed as shown below.
fig.multi-view.eps
1 2
PVW PGM
CH 1 CH 2 CH 3 CH 4
CH 5 CH 6 CH 7 CH 8
3
1. PVW Section (Preview Output)
The video selected on the inactive bus (standby) is shown here. If that bus becomes active, the selected video will become the new program output.
2. PGM Section (Program Output)
The final output is displayed here. This is the program output sent to your displays.
3. CH 1 - CH 8 Section (Source Monitors)
This lets you monitor the video from source equipment connected to channels 1 through 8. A red border is displayed around the channel that is sent to the final output (PGM). A green border is displayed around channel that is on standby (PVW).
* The input source images are displayed here directly (without any parameter changes). Settings such as color adjustment or scaling are not applied.
* Still images imported from USB memory are not displayed on the source monitor.
The frame rate for the DVI-I/HDMI inputs and RGB/Component inputs is reduced by about 5 fps. Images of SDI inputs and composite inputs are displayed at the original frame rate coming from the source devices.
10
About Power Supply
Connect the included power cord to AC IN connector on rear panel. Be sure to use the included power cord for AC connection.
fig.ACconnection.eps
Power cord
About the Ground Terminal
Depending on the circumstances of a particular setup, you may experience a discomforting sensation, or perceive that the surface feels gritty to the touch when you touch this device, video cameras connected to it, or the metal portions of other objects, such as projectors. This is due to an infinitesimal electrical charge, which is absolutely harmless. However, if you are concerned about this, connect the ground terminal (see figure) with an external ground. When the unit is grounded, a slight hum may occur, depending on the particulars of your installation. If you are unsure of the connection method, contact the nearest Roland Service
Center, or an authorized Roland distributor, as listed on the “Information” sheet.
fig.earth-terminal.eps
Unsuitable places for connection
• Water pipes (may result in shock or electrocution)
• Gas pipes (may result in fire or explosion)
• Telephone-line ground or lightning rod (may be dangerous in the event of lightning)
11
About Power Supply
About the Cord Hook
Secure the power cord in place using the cord hook as shown below. This can help prevent power loss due to the plug being pulled out if the power cord is accidentally yanked.
1.
Connect the power cord to the AC IN connector.
fig.connect-AC.eps
2.
Secure the power cord in place with the cord hook.
Clamp the cord hook onto the power cord to secure it in place.
fig.hook-cord.eps
12
About Power Supply
Turning the Power On and Off
Turning the Power On
equipment in the wrong order, you risk causing malfunction or equipment failure.
* This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.
* When still images are saved to the internal memory, booting of this unit will take longer because of preparations.
1.
Connect the peripheral devices.
Connect video cameras or other equipment. Make the connections while the power to all equipment, including the V-800HD, is turned off.
2.
Turn on the power to the V-800HD.
Set the POWER switch on the rear panel to ON to turn on the power to the V-800HD.
fig.power-on.eps
3.
Turn on the power to the source devices.
Turn on the power to the source devices like video cameras connected to the V-800HD.
4.
Turn on the power to the output devices
Turn on the power to the output devices like projectors connected to the V-800HD.
Turning the Power Off
1.
Turn off the power to the output devices.
Turn off the power to the output devices connected to the V-800HD.
2.
Turn off the power to the V-800HD.
Set the POWER switch on the rear panel to OFF to turn off the power to the V-800HD.
1.
Turn off the power to the source devices.
Turn off the power to the source devices connected to the V-800HD.
Do not turn off the power while a message of “Processing...“ is shown on menu display area of the multi-view monitor. Your settings may not be saved properly.
13
Top Panel
fig.top-panel.eps
1
2
3
4
5
6
Part Names and Functions
12 13 14 15
1 USB Port
* Open the sliding cover only when you are using the USB port. When this is not in use, be sure to keep the sliding cover closed to protect the connector inside.
Use these menu controls to change settings on the V-800HD.
You can zoom in/out the screen or adjust the display location. When you are applying Picture-in-Picture, you can use controls in
this section to adjust the display location and size of the inset screen (p. 36, p. 41).
5 INPUT STATUS Indicators
The indicators here indicate the input status for cross-points. They light up when valid signals are input.
6 Cross-Points
10 buttons each on the [PGM] and [PST/EFFECT] sides. Use these to select the output video and standby video.
• PGM
The button for the channel currently being output lights up in red, and the channel is displayed in [PGM] section of the multi-view monitor.
• PST/EFFECT
These select the video you want to output (put into standby) next, and the source for compositing, such as the inset screen for Picture-in-
Picture. Pressing a button to select the source makes the button light up in green. (When a compositing effect is applied, the button lights up in red.) The video is also displayed in the [PVW] section of the multi-view monitor. You can switch from standby to output by operating the [CUT] or [AUTO] button or the video fader.
By default, inputs from source devices are assigned to [1] through [8]. A still image is assigned to [9], and plain color video (by default, black) is assigned to [10]. For information on changing button and source combinations, refer to “Changing Cross-Points”
14
7
8
9
10
11
Part Names and Functions
These display the status of synchronization and the format of the output signal (p. 24).
• REFERENCE
[INTERNAL] lights up during synchronization to the internal clock of the V-800HD, and [EXTERNAL] lights up during synchronization to an external source. The indicator flashes when the V-800HD cannot synchronize with the external device.
• OUTPUT FORMAT
HD 480p, 576p, 720p, 1080i, 1080p
RGB VGA (640x480) through WUXGA (1920x1200)
• HDCP
Refer to “Inputting HDCP Signals” (p. 29).
9 OUTPUT FADE Button
This applies fade to program output. The button flashes while the fade is in progress. The button lights up continuously when a
fade-out has been completed. The button goes dark when a fade-in has been completed (p. 34).
and their items, download “Reference Manual” from the following Roland website.
http://www.rolandsystemsgroup.net/
image (freeze frame) made from the video currently being output (p. 48).
10 TRANSITION Dial and Indicator
Use this dial to set the transition time (p. 31).
* You can use the menus to change time unit to be displayed here. By default, the unit is second. You can change it to frames or to seconds + frames.
11 WIPE PATTERN Selectors
These select the effect used for a video transition.
* You can use the menus to assign other wipe patterns to the buttons.
12 DSK Button
This makes the DSK source appear or disappear. It lights when the key source video is displayed and goes dark when the key
source video is removed. (p. 39).
* The length of time for appearance/disappearance depends on the setting for transition time.
13 CUT Button
Press this button to output the channel in standby. Pressing this button provides an immediate hard cut between sources.
14 AUTO Button
Press this button to output the channel in standby. Pressing this button applies the transition effect selected using the [WIPE
PATTERN] selectors.
15 Video Fader
You can use the video fader instead of the [CUT] or [AUTO] buttons to perform a transition manually. When the transition is made manually, the time for transition effect changes depending on movement of the fader, regardless of the setting for transition time.
15
Part Names and Functions
Rear Panel
fig.rear-panel.eps
1 2 3 4 5
6
7
8
9 10 11 12 13 14 15 16
This turns the power to the V-800HD on and off.
2 MIDI IN and OUT/THRU Connectors
You can use these when you remote control the unit from an external MIDI device (a device compatible with MIDI VISUAL
CONTROL or the like), or when using the unit to perform remote control of another device.
You can use this when you remote control the unit from an external RS-232C device.
* For information about operating the unit remotely via MIDI or the RS-232C interface, download the “Remote Control Guide” from the following
Roland website.
http://www.rolandsystemsgroup.net/
Connect devices provided with tally-light feature (p. 25).
5 COMPOSITE IN Connectors
Connect video cameras or other equipment capable of composite output. Composite inputs are assigned to channels 1 through 4.
By default, SDI IN 1 through 4 are selected as the sources for channels 1 through 4. To enable composite input, use the menus to change the
source. Refer to “Making a Composite Connection” (p. 20).
6 DVI-I/HDMI IN Connectors
Connect a computer or other source equipment capable of DVI output. DVI input is assigned to channels 5 through 8.
Use the switches to select [DVI-A] or [DVI-D] as required to match the type of output signal from the source equipment. Refer to “Making a DVI/
7 RGB/COMPONENT IN Connectors
At RGB/COMPONENT IN, connect a computer or other source equipment capable of analog RGB output. RGB inputs are assigned to channels 5 through 8.
* By using a conversion cable from component to mini D-Sub 15-pin type, you can also connect equipment capable of Y/Pb/Pr component output.
By default, DVI-I/HDMI IN 5 through 8 are selected as the sources for channels 5 through 8. To enable RGB input, use the menus to change the
source. Refer to “Making an RGB/Component Connection” (p. 22).
8 SDI IN Connectors
Connect video cameras or other source equipment capable of SDI output. SDI inputs are assigned to channels 1 through 4.
* As SDI source equipment, you can connect devices that output 3G-SDI, HD-SDI or SD-SDI signals.
16
Part Names and Functions
Securing the power cord in place using the cord hook can help prevent power loss due to the plug being pulled out if the power cord is accidentally yanked.
10 AC IN Connector
This is for connecting the included power cord.
11 REFERENCE IN/THRU Connectors
Connect an external source device for synchronization to the REFERENCE IN connector. When supplying a synchronizing signal to an external device via the V-800HD, use the REFERENCE THRU connector.
12 SD OUT Connector
Video converted to NTSC or PAL is output here, irrespective of the output format of the SDI OUT or DVI-D/HDMI OUT connectors.
* When HDCP (p. 29) is set to [ON], nothing is output from the SD OUT connector.
13 HDMI OUT Connector
Connect a multi-view monitor here (p. 9).
14 DVI-D/HDMI OUT Connectors
Connect a projector or other output equipment capable of DVI-D input. By using a conversion cable from DVI-D to HDMI, you can also connect equipment capable of HDMI input.
15 SDI OUT Connectors
Connect a TV monitor, a video deck, or other equipment capable of SDI input.
* When the setting for HDCP signal input has been made, nothing is output from these connectors.
* When the output format is set to RGB or 480p/576p, nothing is output from these connectors.
16 RGB/COMPONENT OUT Connector
Analog RGB/component signals are output from here, irrespective of the output format of the SDI OUT or DVI-D/HDMI OUT connectors. Separate scaling is possible for analog output.
* By using a conversion cable from mini D-Sub 15-pin type to component, you can also connect equipment capable of Y/Pb/Pr component input.
* When HDCP (p. 29) is set to [ON], nothing is output from the RGB/COMPONENT OUT connectors.
For information on the output format setting, refer to “Selecting the Output Format” (p. 26).
17
Part Names and Functions
Signal Flow
The internal signal flow of the V-800HD is as shown below.
fig.signal-flow.eps
Composite Composite Composite Composite DVI-I/HDMI
SDI SDI SDI SDI
RGB/
Component
DVI-I/HDMI DVI-I/HDMI
RGB/
Component
RGB/
DVI-I/HDMI
Component
RGB/
Component
Shared
Input
Shared
Input
Shared
Input
Shared
Input
Shared
Input
Shared
Input
Still
Image
Still
Image
Background
1 2 3
PVW
PGM
4 5
Frame Sync / Scaler / Color Correct
6 7 8 9 10
Color Correct
5
Cross-Point
1
Video Mixer / PinP / Key
2
DSK Mixer
4
Output Fade
Ext Key
Key
Source
Channel
3
Fade to Still Image
Output Freeze
Fade to Background
1
2
Mixer Input
Mixer Output
3 DSK Source
4
5
DSK Output
Still Image
PVW PGM AUX
Selector
Color
Correct
Color
Correct
Color
Correct
Color
Correct
Output Capture
Scaler
Color
Correct
Scaler
Color
Correct
HDMI OUT SDI OUT 1 SDI OUT 2
DVI-D/HDMI
OUT 1
DVI-D/HDMI
OUT 2
RGB/
COMPONENT
OUT
SD OUT
Areas in the figure that are connected by dotted lines cannot be used simultaneously. For example, when assigning a still image to output fade or freezing the output, assigning the still image to channel 10 is not possible. In such cases, change the source on channel 10 to plain colored video
(background color).
18
Connecting External Equipment
Connect external equipment as shown in this chapter. For information on specific connection methods, refer to the following pages.
* To prevent malfunction or damage to video monitors or other devices, always turn off the power on all devices before making any connections.
fig.peripheral-connection.eps
About Input Formats
Signals of the formats shown below can be input from source equipment.
* RGB/DVI refresh rates are the maximum value at the respective resolution.
SDI
480/59.94i, 576/50i, 720/50p, 720/59.94p, 1080/50i, 1080/59.94i, 1080/50p, 1080/59.94p
Component
480/59.94i, 576/50i, 480/59.94p, 576/50p, 720/59.94p, 720/50p, 1080/59.94i, 1080/50i, 1080/59.94p, 1080/50p
RGB
640x480/60 Hz, 800x600/60 Hz, 1024x768/60 Hz, 1280x768/60 Hz, 1280x1024/60 Hz, 1366x768/60 Hz, 1400x1050/60 Hz,
1600x1200/60 Hz, 1920x1200/60 Hz (Reduced Blanking)
DVI/HDMI
640x480/60 Hz, 800x600/60 Hz, 1024x768/60 Hz, 1280x768/60 Hz, 1280x1024/60 Hz, 1366x768/60 Hz, 1400x1050/60 Hz,
1600x1200/60 Hz, 1920x1200/60 Hz (Reduced Blanking), 480/59.94i, 576/50i, 480/59.94p, 576/50p, 720/59.94p, 720/50p, 1080/
59.94i, 1080/50i, 1080/59.94p, 1080/50p
Composite
480/59.94i, 576/50i
The V-800HD automatically detects the input format.
For information on output format, refer to “Selecting the Output Format” (p. 26).
19
Connecting External Equipment
Connecting Source Equipment
Connecting Video Sources
Making SDI Connections
Connect SDI equipment such as video cameras or video decks to the SDI IN connectors. SDI inputs are assigned to channels 1 through 4. The type of signal output from the source equipment (3G-SDI, HD-SDI or SD-SDI) is detected automatically.
fig.SDI-connection.eps
You can connect 3G-SDI, HD-SDI or SD-SDI source equipment to the SDI IN connectors. If a signal is input that has an aspect ratio different form
Crop, or Squeeze.
Making Composite Connections
Connect equipment capable of composite output such as video cameras or DVD players to the COMPOSITE IN connectors.
* When connecting equipment that has an RCA pin type output jack, use a conversion plug.
fig.composite-connection.eps
20
Connecting External Equipment
Connecting source equipment to a COMPOSITE IN connector requires changing the setting on the V-800HD. Use the procedure described below to change the source from SDI to composite.
1.
Display the Input menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [Input], then press the [ENTER] button to display the Input menu.
fig.open-input-menu.eps
スクリーンショット
2.
Select the channel.
Use the [CURSOR] buttons to select which input format you wish to use at this input channel.
fig.select-channel.eps
3.
Change the assignment.
Turn the [VALUE] dial to change the setting to [Composite] or [3G/HD/SD-SDI], depending on which source type is plugged into that input.
fig.change-assign.eps
4.
Exit the menu.
Press the [EXIT] button several times to quit the menu.
fig.close-menu.eps
21
Connecting External Equipment
Connecting a Computer or HDMI Equipment
Making a DVI/HDMI Connection
Connect computers and video cameras capable of DVI or HDMI output to the DVI-I/HDMI IN connectors. Inputs are assigned to channels 5 through 8.
* For equipment capable of HDMI output, make the connection using a conversion cable.
By default, the V-800HD does not support HDCP (High-bandwidth Digital Content Protection). When inputting video to which HDCP is applied,
refer to “Inputting HDCP Signals” (p. 29) and change the settings on the V-800HD.
fig.connect-PC-DVI.eps
RGB - DVI
DVI-A DVI-D DVI-D
Use the switch shown below for each respective connector to select [DVI-A] or [DVI-D] to match the type of output signal from the computer. If this switch is set incorrectly, you will not have any input signal. When [DVI-A] has been selected, analog RGB can also be connected. In such cases, use a conversion cable from mini D-Sub 15-pins to DVI.
fig.DVI-selection.eps
Making an RGB/Component Connection
Connect computers capable of analog RGB output to the RGB/COMPONENT IN connectors.
By using a conversion cable from component to mini D-Sub 15-pins type, you can also connect equipment capable of component output.
fig.RGB-connectin.eps
22
not possible. Adjust the output resolution and refresh rate of your computer to match the valid input format.
Connecting External Equipment
Connecting source equipment to RGB/COMPONENT IN connectors requires changing a setting on the V-800HD. Use the procedure described below to change the source from DVI to RGB/Component.
1.
Display the Input menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [Input], then press the [ENTER] button to display the Input menu.
fig.open-input-menu.eps
スクリーンショット
2.
Select the channel.
Use the [CURSOR] buttons to select which input format you wish to use at this input channel.
* If the target channel is not displayed, press the left or right [CURSOR] button to change the page.
fig.select-channel-RGB.eps
3.
Change the assignment.
Turn the [VALUE] dial to change the setting to [RGB/Component].
fig.change-assign-RGB.eps
4.
Exit the menu.
Press the [EXIT] button several times to quit the menu.
fig.close-menu.eps
23
Connecting External Equipment
About Sharing a Source
Channels 1 through 4 and channels 5 through 8 can share source video. Using this feature, you can assign the video on channel 1 to channels 2 through 4 and the video on channel 5 to channels 6 through 8.
When shared, a single source video is assigned to multiple cross-point buttons. To share, go to the input format display area of the Input menu and select [Shared Input].
* Only the source of the previous adjacent channel can be shared. Therefore, when sharing the source on channel 1 with channels 2 through 4,
[Shared Input] must be selected for each channel from 2 to 4.
fig.shared-input.eps
Composite Composite
SDI
Composite
SDI
Composite
SDI
SDI
Shared
Input
Shared
Input
Shared
Input
Ch 1 Ch 2 Ch 3 Ch 4
DVI-I/HDMI
RGB/
Component
DVI-I/HDMI
RGB/
Component
Shared
Input
DVI-I/HDMI
RGB/
Component
Shared
Input
DVI-I/HDMI
RGB/
Component
Shared
Input
Ch 5 Ch 6
Connecting a Clock Source
Ch 7
You can connect a source device for synchronizing.
* You can send (thru-out) the synchronizing signal from the THRU connector.
fig.connect-clock-source.eps
Ch 8
The V-800HD supports the external clocks shown below. To synchronize with an external clock, select [Reference] in System menu and set the value to [External].
• Black burst (frame synchronization)
• Bi-level synchronization, tri-level synchronization
The composite output from SD OUT jack always synchronizes to the V-800HD's internal clock regardless to the setting of [Reference] parameter.
24
Connecting External Equipment
Connecting Output Equipment
Connecting a Projector
Connect to an RGB/COMPONENT OUT connector or to a DVI-D/HDMI OUT connector, depending on the input connector on the projector.
fig.connect-projector.eps
Connecting Recording Equipment
Connect recording equipment such as video decks to the SD OUT connector or to an SDI OUT connector.
* NTSC or PAL video is output from the SD OUT connector, irrespective of the setting for output format on the V-800HD.
fig.connect-recorder.eps
Tally Output
The V-800HD is equipped with two D-Sub 15-pins TALLY connectors. Connecting a video monitor capable of tally input to these makes it possible to illuminate the tally lamps on the monitor. The lamp is switched on and off according to the channel selection, enabling you to see which channel is currently in use on the monitor.
* The specifications of TALLY connectors are as below.
• D-sub 15-pin type, max input: 12 V/200 mA
• Open-collector type
The channels shown below are assigned to the TALLY 1 and 2 connectors on the V-800HD.
fig.tally-assign.eps
TALLY 1 TALLY 2
Female Connector
5 4 3 2 1
10 9 8 7 6
15 14 13 12 11
9
10
7
8
5
6
3
4
1
2
11
12
13
14
15
Pin No.
Channel
PGM Ch.1
PST Ch.1
NC
GND
PGM Ch.4
PGM Ch.2
PST Ch.2
NC
GND
PST Ch.4
PGM Ch.3
PST Ch.3
NC
GND
NC
9
10
7
8
5
6
3
4
1
2
11
12
13
14
15
Pin No.
Channel
PGM Ch.5
PST Ch.5
NC
GND
PGM Ch.8
PGM Ch.6
PST Ch.6
NC
GND
PST Ch.8
PGM Ch.7
PST Ch.7
NC
GND
NC
25
Selecting the Output Format
RGB/COMPONENT OUT connectors will be stopped. Note, however, that HDCP-applied output from the DVI-D/HDMI OUT connectors and output to the multi-view monitor will continue.
About the Setting for the Output Format
This selects the format of the main output (digital) and analog outputs shown below. Signals that have different resolutions can be output from digital and analog connectors.
fig.output-flow.eps
Main Output Format
PGM PVW AUX
Analog Output Format
Selector
RGB/Component
Format
Composite
Format
SDI OUT 1 SDI OUT 2 DVI-D/HDMI
OUT 1
DVI-D/HDMI
OUT 2
RGB/COMPONENT OUT SD OUT
The [OUTPUT FORMAT] indicator for the format selected for the main output lights up. The corresponding output formats of the
SD, HD, and RGB indicators are as follows.
• HD
• RGB
480p, 576p, 720p, 1080i, 1080p
VGA (640x480) through WUXGA (1920x1200)
* By default, [HD] is selected, and the unit is set to output 1080i.
fig.format-indicator.eps
For information on the selectable output formats, refer to “About the Output Formats of the Connectors” on the following page.
26
Selecting the Output Format
Changing the Format of the Main Output
This changes the output format of the SDI OUT connectors and DVI-D/HDMI OUT connectors. This setting is shown by the
[OUTPUT FORMAT] indicators.
1.
Display the Output menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [Output], then press the [ENTER] button to display the Output menu.
fig.open-output-menu.eps
2.
Select the main output.
Use the [CURSOR] buttons to go to [Format] and select the [Main] format display area, then use the [VALUE] dial to change the format.
fig.change-format.eps
3.
Exit the menu.
Press the [EXIT] button several times to quit the menu.
fig.close-menu.eps
27
Selecting the Output Format
About the Format Setting for RGB/Component and Composite Output
After setting the format for the main (digital) output, you can also carry out scaling. At the Output menu, select [RGB/Component] or [Composite], and you can then turn the [VALUE] dial to set the output format.
* The format settings for analog outputs will not be shown by the [OUTPUT FORMAT] indicators.
About Color Correction for Output
Using the menus, you can apply color correction separately to the main outputs and to analog outputs. For information on the details of menus and their items, download the “Reference Manual” from the following Roland website.
http://www.rolandsystemsgroup.net
About the Output Formats of the Connectors
The V-800HD can output signals of the following formats from the various output connectors. But the output to the multi-view monitor (the HDMI OUT connector) is fixed at 1920x1080/60 Hz.
The format you can select differs depending on the system frame rate of the V-800HD.
SDI OUT Connectors
480/59.94i, 576/50i, 720/50p, 720/59.94p, 1080/50i, 1080/59.94i, 1080/50p, 1080/59.94p
RGB/COMPONENT OUT Connectors
640x480, 800x600, 1024x768, 1280x768, 1280x1024, 1366x768, 1400x1050, 1600x1200, 1920x1200,
480/59.94p, 576/50p, 720/59.94p, 720/50p, 1080/59.94p, 1080/50p
* For switching of 59.94p and 50p, go to the System menu and use [Frame Rate] to select [59.94Hz] or [50Hz].
DVI-D/HDMI OUT Connectors
640x480, 800x600, 1024x768, 1280x768, 1280x1024, 1366x768, 1400x1050, 1600x1200, 1920x1200, 480/59.94i, 576/50i, 480/
59.94p, 576/50p, 720/59.94p, 720/50p, 1080/59.94i, 1080/50i, 1080/59.94p, 1080/50p
* The underlined formats are output at 75 Hz when the system refresh rate is set at 50 Hz.
SD OUT Connectors
480/59.94i, 576/50i
* Output from the SD OUT connector is always 480/59.94i or 576/50i, irrespective of the setting for output format.
About the Setting for the Output Source
On the V-800HD, you can select PGM, PVW, or AUX as the output source. Display the Output menu and select an output connector. Then you can select [PGM], [PVW] or [AUX].
* Separate sources can be assigned to SDI OUT (1/2) and DVI/HDMI OUT (1/2), but the source for the RGB/COMPONENT OUT and COMPOSITE
OUT connectors will be changed simultaneously.
28
Inputting HDCP Signals
By default, the V-800HD does not support HDCP (High-bandwidth Digital Content Protection). This means that HDCP-applied signals from Blu-ray Disc players and the like cannot be input. When inputting signals to which HDCP is applied, follow the procedure shown below to change the setting.
* HDCP is copyright-protection technology that prevents unlawful copying of content.
1.
Display the System menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [System], then press the [ENTER] button to display the System menu.
fig.open-system-menu.eps
2.
Change the setting.
Use the [CURSOR] buttons to select [HDCP]. Turn the [VALUE] dial to change the setting from [OFF] to [ON]. A confirmation screen appears. Press the [ENTER] button.
fig.HDCP-setting.eps
3.
Exit the menu.
Press the [EXIT] button several times to quit the menu.
fig.close-menu.eps
When the setting change just described has been made, output from the SD OUT, SDI OUT, and RGB/COMPONENT OUT connectors will be stopped. Note, however, that HDCP-applied output from the DVI-D/HDMI OUT connectors and output to the multi-view monitor will continue.
fig.HDCP-signal-flow.eps
OFF
RGB/COMPONENT OUT
DVI-D/HDMI OUT
SDI OUT
SD OUT
HDMI OUT
ON
SDI OUT
SD OUT
RGB/COMPONENT OUT
DVI-D/HDMI OUT
HDMI OUT
29
Inputting HDCP Signals
About the HDCP Indicator
The [HDCP] indicator on the top panel operates as described below.
• It lights up when an HDCP compatible device is connected as the output device.
• It flashes when nothing is connected or when the connected device is not compatible with HDCP.
• It goes dark when [HDCP] is set to [OFF].
About Verification of HDCP compatible Equipment
You can examine the HDCP compatibility of source equipment and output equipment. From the Input menu or Output menu, selecting [HDCP] displays a screen like the one shown below.
* If the target channel is not displayed, press the left or right [CURSOR] button to change the page.
fig.HDCP-status.eps
30
Basic Operations
Using Buttons to Switch the Video
Applying Transition Effects
Using the [AUTO] button, you can apply transition effects during video switching. The transition effects are applied according to the settings of transition time and wipe pattern.
1.
Move the video fader all the way.
Before the transition, move the video fader all the way toward either the front or the back.
fig.fader-max.eps
or
2.
Set the transition time.
Turn the TRANSITION [TIME] dial to set the time for the transition effect.
* By default, the transition time is set at 1 second. When the unit is started for the first time, the indicator displays [1.0].
mode.
fig.time-dial.eps
3.
Select the transition effect.
Use the buttons in the WIPE PATTERN section to choose a transition effect.
fig.wipe-pattern.eps
• MIX The transition is made progressively as the two pictures are mixed.
• WIPE 1 - 7 The transition is made using one of the following wipe patterns.
fig.pattern-select.eps
1 2 3 4 5 6 7
You can also use the menus (p. 51) to select a different pattern and the direction of the wipe.
31
Basic Operations
4.
Select the channel you want to output next (standby).
Use the cross-points on the [PST/EFFECT] side to choose the channel you want to output next. Pressing the button makes it light up in green. On the multi-view monitor, the selected channel is displayed with a green border around it. The video on the selected channel is also displayed in the [PVW] section.
* The 9 and 10 buttons on the [PST/EFFECT] side are used when outputting a still image or a color background.
* You can change the source assignments to cross-points (p. 49).
fig.select-PST.eps
5.
Switch the video.
Preview the standby video, and press the [AUTO] button when you want to make the transition. The picture changes and the
[PGM] button for the selected channel lights up in red. On the multi-view monitor, a red border is displayed around the channel being output. The output video is also displayed in the [PGM] section. The channel selected before transition on the [PGM] side becomes the selected one on the [PST/EFFECT] side.
* The button flashes while the transition effect is applied. On the multi-view monitor, the border around the source video turns to red.
fig.AUTO-button.eps
Switching without Transitions Effects
Using the [CUT] button makes the video change instantly, with no transition effect applied. Use [PST/EFFECT] buttons 1 through 8 to select the channel you want to output next, then press the [CUT] button.
fig.CUT-button.eps
32
Basic Operations
Using the Fader to Switch the Video
When you use the [AUTO] button to switch, the transition effect is applied according to the setting of transition time. Using the video fader, you can control the transition time manually.
1.
Move the video fader all the way.
Before the transition, move the video fader all the way toward either the front or the back.
fig.fader-max.eps
or
2.
Select the transition effect.
Use the buttons in the WIPE PATTERN section to choose a transition effect.
3.
Select the channel you want to output next (standby).
Use the cross-points on the [PST/EFFECT] side to choose the channel you want to output next. Pressing the button makes it light up in green. On the multi-view monitor, the selected channel is displayed with a green border around it. The video on the selected channel is also displayed in the [PVW] section.
4.
Switch the video.
Move the video fader in the opposite direction of step 1. The button of the channel on [PGM] side lights up in red. On the multiview monitor, a red border is displayed around the channel being output. The output video is also displayed in the [PGM] section.
The channel selected before transition on the [PGM] side becomes the selected one on the [PST/EFFECT] side.
* The button lights up while you are moving the video fader. On the multi-view monitor, a red border is displayed around the source video.
fig.move-fader.eps
The channel to output always changes from the [PST/EFFECT] side to the [PGM] side, irrespective of the fader movement direction.
33
Basic Operations
Applying Fade to Final Output
You can use the [OUTPUT FADE] button to apply a fade to the final output of the V-800HD. Applying a fade makes the output video gradually disappear (fade-out) or appear (fade-in).
fig.output-fade.eps
1.
Apply a fade-out.
Pressing the [OUTPUT FADE] button makes the button flash and starts a fade-out. When the fade-out has been completed, the button stops flashing and stays lit.
2.
Apply a fade-in.
Pressing the button a second time makes it flash and starts a fade-in. When the fade-in has been completed, the button goes dark.
You can use the menus (p. 51) to change the following settings related to fades.
• Fade time The default setting is 0.5 seconds.
• Fade color The default setting is black.
Fades to Other Images
Fades to plain color (like black) are possible. Using menus, you can change settings.
Fade to Still Image
System menu, select [Output Fade], then for the [Mode] setting, select [Fade to Still Image].
If the still image is assigned to channel 10, then assigning the still image to an output fade or freezing the picture during output is not possible.
Also, when you are freezing the video during output, the source on channel 10 changes to a plain colored image (background color).
Fade to Output Freeze
setting, select [Output Freeze].
34
Compositing the Video
Picture-in-Picture (PinP)
This displays an inset screen superimposed upon a background picture. Use the dial and joystick of the SCALING section to adjust the size and position of the inset screen.
Luminance Key/Chroma Key/External Key (KEY)
This performs compositing with a key-extracted video superimposed upon a background video. Use the [LEVEL] dial to adjust the amount of keying.
* When you are using external key, DSK cannot be used.
Downstream Keyer (DSK)
You can make the results of a video transition or of PinP or of key compositing the background. Then overlay a logo or text (threelayer compositing). You can switch or composite the background video while continuing to display the logo or text unchanged.
Use the [LEVEL] dial to adjust the amount of keying.
Even if you switch video while compositing is carried out, no glitch occurs to the output video. You can switch the foreground picture (the inset screen for Picture-in-Picture, or the logo /text) or the background picture smoothly.
Compositing Using Picture-in-Picture
This composites an inset screen into background video.
fig.PinP-image.eps
Inset Screen
Picture in Picture
Background
1.
Select the background channel.
Use buttons 1 through 8 on the [PGM] side to select the background channel.
* When you want to use a still image or a plain colored background, press select 9 or 10.
fig.select-background.eps
35
Compositing the Video
2.
Select the channel of the inset screen.
Use buttons 1 through 8 on the [PST/EFFECT] side to select the channel of the inset screen.
fig.select-inset.eps
3.
Preview the result of compositing.
Press any [PinP] position button to make it light up in green. The location where the inset screen is displayed varies depending on the button you press. When any of the [PinP] buttons is lighted, a preview of the compositing result is displayed in [PVW] section of the multi-view monitor. At this stage, the final output has not yet been changed.
fig.press-PinP-button.eps
4.
Adjust the size and position.
Go to the SCALING section and use the [CONTROL] button to select [PinP]. Use the [SIZE] dial and the [POSITION] joystick to adjust the size and positioning.
* You can use the menus to save the size and position as well as settings for border color, width, and other parameters to individual PinP position buttons. You can also zoom the picture in the inset screen.
fig.adjust-size-position.eps
5.
Output the composited result.
Use the [AUTO] or [CUT] button or the video fader to output the result of compositing. The color of the PinP position button changes to red at this time.
6.
Make the inset screen disappear.
Pressing the [AUTO] or [CUT] button again or moving the video fader in the opposite direction makes the inset screen disappear.
Making a second press of the [PinP] button you pressed in step 3 also makes the inset screen disappear.
You can use the menus to move the displayed position inside the inset screen. For information on the details of menus and their items, download
“Reference Manual” from the following Roland website.
http://www.rolandsystemsgroup.net/
36
Compositing Using Luminance/Chroma Key
You can perform compositing using luminance key or chroma key.
* By default, black extraction is applied. You can select a different color using the menus (p. 51).
fig.key-image.eps
Black or White
Luminance Key
Blue or Green
Chroma Key
1.
Select the background channel.
Use buttons 1 through 8 on the [PGM] side to select the background channel.
fig.select-background.eps
Compositing the Video
2.
Select the channel to overlay.
Use buttons 1 through 8 on the [PST/EFFECT] side to select the channel to overlay.
fig.select-foreground.eps
3.
Preview the results of compositing.
At the KEY section, press the [ON] button to make it light up green. When the [ON] button lights up, a preview of the compositing result is displayed in [PVW] section of the multi-view monitor. At this stage, the final output has not yet been changed.
fig.press-key-on.eps
37
Compositing the Video
4.
Adjust the amount of keying.
While viewing the preview, turn the [LEVEL] dial in the KEY section to adjust the amount of keying.
* You can use the menus to change the degree of edge blur. At the Key menu, adjust [Gain]. Also, when you are using chroma key, you can use
[Hue] to adjust the extraction color.
fig.adjust-key-level.eps
5.
Output the composited results.
Use the [AUTO] or [CUT] button or the video fader to output the results of compositing. The color of the [ON] button changes to red at this time.
6.
Make the overlaid picture disappear.
Pressing the [AUTO] or [CUT] button again or moving the video fader in the opposite direction makes the overlaid video disappear. Making a second press of the [ON] button you pressed in step 3 also makes the overlaid picture disappear.
Combining Picture-in-Picture and luminance/chroma key lets you use the [SIZE] dial to enlarge or reduce the size of the overlaid picture. You can also use the [POSITION] joystick to move the display position. When combining, press any of the [PinP] buttons to make it light up.
fig.key-PinP-sample.eps
KEY only KEY + PinP
About External Key
At the Key menu, selecting [Mode] and changing the setting to [External Key] lets you perform compositing using an external key source.
* You can select either white or black as the extraction color. Go to [Type] of the Key menu to make the setting.
fig.ext-key-image.eps
Key Fill Key Source
PGM PST/EFFECT
External Key
Key Source
Channel
38
The channel where the external key source is input must be set at the Key menu. Select the channel in [Key Source Channel]. The procedure for compositing is the same as for luminance key or chroma key.
When you use external key, DSK cannot be used.
Compositing the Video
Compositing Using DSK
By default, channel 8 is set as the source for the DSK. Also, by default, the unit is set to extract black. A white logo or text on black background can be extracted clearly.
* You can change the DSK source channel or extraction color using the menus (p. 51).
fig.DSK-image.eps
Jazz Night
DSK
Jazz Night
1.
Check the background video.
On [PVW] section of the multi-view monitor, confirm the video to be the background.
2.
Preview the result of compositing.
At the DSK section, press the [PVW] button to make it light up. The video overlaid with the logo or text from source channel (by default, channel 8) is displayed in [PVW] section of the multi-view monitor. At this stage, the final output has not yet been changed.
fig.DSK-PVW.eps
3.
Adjust the amount of keying and the degree of edge blur.
While viewing the preview, use the [LEVEL] dial in the DSK section to adjust the amount of keying.
* You can use the menus to change the degree of edge blur. At the DSK menu, adjust the setting for [Gain]. You can also use [Hue] to adjust the extraction color.
fig.DSK-level.eps
39
Compositing the Video
4.
Output the composited results.
Press the [DSK] button to output the results of compositing. The logo or text fades in. The fade time depends of your setting of transition time.
fig.DSK-button.eps
5.
Switch the background picture.
You can change the background picture while continuing to display a logo or text unchanged. Use the buttons on the [PST/
EFFECT] side to select the standby video, then use the [AUTO] or [CUT] button or the video fader to change the background picture.
When you are using external key, DSK cannot be used. When using DSK, be sure to set [Key Mode] to [Self Key].
The settings of a compositing operation for a DSK source will be remembered. Just press the DSK button to make the DSK source appear or disappear.
40
About Other Features
Enlarging/Reducing the Picture
Using the [SIZE] dial in the SCALING section, you can enlarge or reduce the view of the picture. You can also use the [POSITION] joystick to change the display position.
* On the V-800HD, you can enlarge or reduce the picture within a range of 10% to 1,000%.
Enlarging/Reducing the Source Picture
1.
Put the picture you want to enlarge or reduce into standby.
On the [PST/EFFECT] side, select the channel of the picture you want to enlarge or reduce.
2.
Enlarge or reduce the picture, and adjust its display position.
At the SCALING section, press the [CONTROL] button to make the [INPUT] indicator light up. The results of the adjustments using the [SIZE] dial and the [POSITION] joystick are shown on [PVW] section of the multi-view monitor.
* Note, however, that the picture on the source monitor will not be modified.
fig.scale-PVW.eps
3.
Output the enlarged or reduced picture.
Use the [AUTO] or [CUT] button or the video fader to output the picture on standby.
You can also enlarge or reduce the picture and adjust its display position by changing the values of [Zoom] and [Position] in the Input menu. In the Input menu, you can also change cropping parameters and the aspect ratio for the picture.
Enlarging/Reducing the Currently Output Picture
At the SCALING section, press the [CONTROL] button to make the [OUTPUT] indicator light up. You can enlarge or reduce the picture by using the [SIZE] dial. You can also use the [POSITION] joystick to change the display position. The results of the adjustments are shown on [PGM] section of the multi-view monitor.
fig.scale-PGM.eps
You can also enlarge or reduce the picture and adjust its display position by changing the values of [Zoom] and [Position] in the Output menu. In the Output menu, you can also enlarge or reduce the vertical/horizontal size of the picture independently.
41
About Other Features
Changing the Multi-view Labels
You can change the text strings for channel names and the like displayed on the multi-view monitor. Up to 8 characters of text can be displayed.
1.
Display the System menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [System], then press the [ENTER] button to display the System menu.
fig.open-system-menu.eps
2.
Select the channel whose text string you want to change.
Use the [CURSOR] buttons to select [Multi-View Label], then press the [ENTER] button. From among either [PGM] and [PVW] or [CH
1] through [CH 8], use the [CURSOR] buttons to select the channel whose text string you want to change. Pressing the [ENTER] button switches the display to the screen for changing the text string.
* You can also hide the labels by going to the [Multi-View Label] list and setting [Indicate] to [OFF].
fig.select-label-channel.eps
3.
Change the text string.
Use the [CURSOR] buttons to move the cursor left or right, and turn the [VALUE] dial to change the text string.
fig.edit-label-name.eps
4.
Exit the menu.
Use the [ENTER] button to finalize the text string, then press the [EXIT] button several times to quit the menu.
The display on the multi-view monitor is not updated while editing is in progress. The display is updated when you quit the menu.
42
About Other Features
Saving Settings to MEMORY Buttons
You can save the current settings to a MEMORY button. The V-800HD’s internal memory contains banks from 1 to 8, and up to 8 sets of settings can be saved in each bank, for a total of up to 64.
When [Memory Protect] on the System menu is set to [ON], saving operations is not possible.
Saving the Current Settings
This saves the current state of the V-800HD.
1.
Put the unit in the state you want to save.
Operate the dials and buttons on the panel to put the unit in the state you want to save.
2.
Put the unit in standby for saving.
Press the [STORE] button to make the unit in standby for saving. The MEMORY button selected last time flashes at this stage.
fig.save-memory.eps
3.
Select the bank to save to.
Go to the MEMORY section and press the [BANK] button. The button for the currently selected bank lights up. Choose a bank from
[1] to [8] to select the destination for saving.
fig.press-bank.eps
4.
Select the number to save to.
Press a button from [1] to [8] to select the destination for saving. Settings are saved at the selected number in the selected bank.
fig.select-button.eps
Recalling Saved Settings
When the V-800HD starts, memory 1 in bank 1 is loaded. You can call up the settings saved at a different bank and memory number by using the [BANK] button to select the bank, then pressing the button for the number you want to call up.
Going to the System menu and setting [Memory Switch Fade] to [ON] automatically applies an output fade when saved settings are called up.
When recall finishes and the settings have changed, the output fade will be ended.
Settings related to remote control and settings of output-fade cannot be saved individually. Only a single set of settings related to these can be saved. The settings are saved when you quit the menu display.
43
About Other Features
Using a USB Memory Device
Connecting and Formatting a USB Memory Device
Carefully insert the USB memories all the way in-until it is firmly in place.
fig.connect-USB-memory.eps
* Open the sliding cover only when you are using the USB port. When this is not in use, be sure to keep the sliding cover closed to protect the connector inside.
* Be careful to orient the USB memory device correctly front and back and in the correct direction for insertion, and insert it firmly, as far as it will go. Never insert using undue force.
Operation has been tested for commonly available USB memory devices, but operation of all USB memory devices is not assured. Depending on the manufacturer and type of the USB memory device, correct operation may not be possible.
Follow the procedure below to format the connected USB memory device. You must format your USB memory device in the V-
800HD or it will not be recognized by the unit.
1.
Display the System menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [System], then press the [ENTER] button to display the System menu.
fig.open-system-menu.eps
2.
Select the Format menu.
Use the [CURSOR] buttons to go to [USB Memory] and select [Format], then press the [ENTER] button.
fig.USB-format-menu.eps
3.
Format the USB memory device.
Pressing the [ENTER] button in step 2 makes the message [Push ENTER to execute] appear. To execute formatting, press the
[ENTER] button.
* Formatting will permanently wipe all data on the USB memory device.
4.
Exit the menu.
Press the [EXIT] button several times to quit the menu.
44
About Other Features
Saving Settings on a USB Memory Device
You can copy data saved in the V-800HD’s internal memory to a USB memory device formatted on the V-800HD. A batch copy of all data in internal memory from 1-1 to 8-8 is carried out at this time.
1.
Display the System menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [System], then press the [ENTER] button to display the System menu.
fig.open-system-menu.eps
2.
Select the Save menu.
Use the [CURSOR] buttons to go to [USB Memory] and select [Parameter], then press the [ENTER] button. The display changes to a screen for selecting the operation.
3.
Select the Save As menu.
Use the [CURSOR] buttons to select [Save As], then press the [ENTER] button. The display changes to a screen for editing the file name.
fig.save-as-menu.eps
4.
Edit the file name.
Use the [CURSOR] buttons to move the cursor left or right, and turn the [VALUE] dial to change the text string.
* The extension of the file name is [V08]. If you have edited the file name on your computer, small letters are displayed after conversion to capitals. fig.file-name-edit.eps
5.
Save to the USB memory device.
Press the [ENTER] button to finalize the file name. Pressing it displays the message [Push ENTER to execute]. To save, press the
[ENTER] button.
6.
Exit the menu.
Press the [EXIT] button several times to quit the menu.
Menu Items for Save/Load Operations
At the System menu, the following operation menu items are displayed under [Parameter] in [USB Memory].
• Load
• Save
• Save As
• Delete
This copies setting values saved on a USB memory device to the V-800HD’s internal memory. The settings in internal memory are overwritten.
This saves settings by overwriting. Selecting this menu item changes the display to a screen for selecting the file to overwrite.
This saves a new set of settings.
This deletes a settings file from the USB memory device. Selecting this menu item changes the display to a screen for selecting the file to delete.
45
About Other Features
Using Still-image Files
On the V-800HD, you can use still-image files in the ways described below. To use a still-image file, first import it into the V-
800HD’s internal memory. Direct output from a USB memory device is not possible.
• You can assign separate still images to channel 9 and channel 10.
• You can save up to 16 still-image files in internal memory. The data remains in memory after the power is turned off.
• You can create and save a still image from output video.
About the Format and Sizes of Still-image Data
Save still-image data onto a USB memory device. The format and size must be as below. Data in other formats or sizes cannot be imported into the V-800HD.
• Format
• Maximum resolution
Bitmap (.bmp), 24 bits/pixel, uncompressed
1920 x 1200
Assigning Still Images to Channels 9/10
Still images saved on a USB memory device can be assigned to channel 9 or channel 10 on the V-800HD.
1.
Save still-image data on a USB memory device.
Save the still-image data in the root directory of a USB memory device formatted on the V-800HD. Use a file name containing no more than eight single-byte alphanumeric characters, and be sure to add the “.bmp” file extension.
2.
Display the System menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [System], then press the [ENTER] button to display the System menu.
fig.open-system-menu.eps
46
About Other Features
3.
Display the menu for loading still images.
At [USB Memory], select [Still Image], then press the [ENTER] button.
* If the target menu is not displayed, press the left or right [CURSOR] button to change the page.
fig.USB-memory-menu.eps
4.
Select the assignment destination for the still image.
Use [Still Image Memory No.] to select the internal memory number ([1] through [16]) for the assignment destination.
* A [*] next to a number indicates that a still image is already assigned to internal memory at that number.
5.
Display the menu for loading still images.
Use the [CURSOR] buttons to select [Load], then press the [ENTER] button. The display changes to a screen for selecting still images.
fig.still-image-menu.eps
6.
Select the still image to import.
Use the [CURSOR] buttons to select a still-image file, then press the [ENTER] button. The message [Push ENTER to execute] appears. Pressing the [ENTER] button once more copies the selected still-image file from the USB memory device to the V-
800HD’s internal memory.
7.
Select the channel for assignment.
Return temporarily to the initial menu screen and select the Input menu. Press the [CURSOR] buttons to select [CH 9] or [CH 10].
* If the target channel is not displayed, press the left or right [CURSOR] button to change the page.
8.
Choose the still image to assign to the selected channel.
Check to make sure the source assignment is [Still Image], then press the [ENTER] button. The display changes to a screen to select memory number. Choose the internal memory number you selected in step 3.
* You can adjust the display position and the color at the same screen.
fig.assign-to-channel.eps
9.
Exit the menu.
Press the [EXIT] button several times to quit the menu.
Deleting Still-image Data from Internal Memory
At the System menu, select [Delete] under [Still Image Memory No.]. Selecting it displays the message [
E xecute]. You can delete the still-image data from internal memory by pressing the [Enter] button once more.
* Deleting still-image data from internal memory shortens startup times.
47
About Other Features
Creating a Still Image from Final-output Video
You can create a still image from the V-800HD’s output video and save it to internal memory (Output Capture).
* The created still image cannot be saved to a USB memory device.
1.
Display the System menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [System], then press the [ENTER] button to display the System menu.
2.
Select [Output Capture].
Use the [CURSOR] buttons to select [Output Capture], then press the [ENTER] button to move to the next screen.
fig.output-capture.eps
3.
Select the source.
Use [Source Bus] to select the source video. You can select from among [PGM], [PVW] or [AUX]. Selecting a source makes the video appear at [PGM] section of the multi-view monitor.
4.
Select the memory of the destination for saving.
Under [Destination], select saving-destination memory number ([1] through [16]) in [Still Image Memory No.].
fig.destination-memory.eps
5.
Execute creation and saving of the still image.
Use the [CURSOR] buttons to highlight [Execute], then press the [ENTER] button. A still image is created from the video being output and saved at the number specified in step 3.
Using the procedure just described to create a still image lets you assign it to channel 9 or 10. You can also assign it to an output
fade (p. 34) in the same way as for still images imported from a USB memory device.
48
About Other Features
Changing Cross-Points
You can assign a source channel to any cross-point button ([1] through [10]). You can also cancel the assignments and disable button operations.
fig.cross-point-concept.eps
Ch.1 Ch.2
Ch.3
Ch.4
Ch.5
Ch.6
Ch.7
Ch.8
Ch.9 Ch.10
Ch.1
Ch.2
Ch.3
Ch.4
Ch.5
Ch.6
Ch.7
Ch.8
Ch.9 Ch.10
1.
Display the System menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [System], then press the [ENTER] button to display the System menu.
2.
Display the cross-point setting screen.
Select [Cross-point Assign], then press the [ENTER] button. The channel assignments for the respective cross points are displayed.
3.
Change the assignments.
Use the [CURSOR] buttons to select a cross-point ([1] to [10]), then turn the [VALUE] dial to change the channel assignment.
fig.cross-point-menu.eps
4.
Exit the menu.
Press the [EXIT] button several times to quit the menu.
49
About Other Features
Returning to the Factory-default State
This returns various settings to their factory defaults. If following the instructions for a procedure results in operation that differs from what is described in the Owner’s Manual, execute a factory reset.
* Executing a factory reset causes all setting values saved up to then to be lost. Please be aware that all settings saved to MEMORY buttons and still images saved in internal memory are also lost.
1.
Display the System menu.
Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [System], then press the [ENTER] button to display the System menu.
2.
Select the Factory Reset menu.
Use the [CURSOR] buttons to select [Factory Reset], then press the [ENTER] button. The message [Push ENTER to execute] appears.
* If the target menu is not displayed, press the left or right [CURSOR] button to change the page.
fig.factory-reset-menu.eps
3.
Execute the factory reset.
Pressing the [ENTER] button executes the factory reset.
4.
Exit the menu.
Press the [EXIT] button several times to quit the menu.
50
Menu Operations
The V-800HD’s setting menus are displayed on the multi-view monitor. Menu operations follow the flow described below. For information on the details of menus and their items, download “Reference Manual” from the following Roland website.
http://www.rolandsystemsgroup.net/
1.
Display the menu.
Press the [MENU] button to display the menu. Displayed initially is the first level, shown below.
fig.1st-level-menu.eps
Input
Output
Transition
PinP
Key
DSK
System
Set input parameters like source assignments.
Set output parameters like output formats.
Set parameters of transition effects.
Set parameters of Picture in Picture.
Set parameters of key compositions.
Set parameters of DSK composition.
Set system configuration of the V-800HD.
2.
Select the target menu.
Use the up and down [CURSOR] buttons to select the target menu. After making the selection, press the [ENTER] button to display the items that the menu contains.
fig.select-menu.eps
3.
Select the item whose setting you want to change.
Use the up and down [CURSOR] buttons to select the target item. If the items span two or more pages, triangle symbols are displayed at the top of the screen. When these symbols are displayed, you can use the left and right [CURSOR] buttons to change the page shown. Also, when [ENTER] is displayed at the top of the screen, you can move down one level by pressing the [ENTER] button.
fig.select-item.eps
4.
Change the setting value.
If the displayed setting value is highlighted, you can change the value by turning the [VALUE] dial.
* You can change a setting value up or down by 10 units at one time by holding down the [ENTER] button and turning the [VALUE] dial. You can also return the setting value to its factory default by holding down the [ENTER] button and pressing the [EXIT] button.
fig.value-dial.eps
5.
Exit the menu.
Press the [EXIT] button to quit the menu screen.
and save the settings before turning off the power.
51
Appendices
Main Specifications
fig.specification-E.eps
Video Processing
Processing
Supported
Formats
Video
RGB
Still
Image
Y:Pb:Pr, 4:4:4, 10 bits
480/59.94i, 576/50i,
480/59.94p, 576/50p
720/59.94p, 720/50p
1080/59.94i, 1080/50i
1080/59.94p, 1080/50p
640 x 480 / 60 Hz, 800 x 600 / 60 Hz,
1024 x 768 / 60 Hz, 1280 x 1024 / 60 Hz,
1280 x 1024 / 60 Hz, 1366 x 768 / 60 Hz,
1400 x 1050 / 60Hz
(Output refresh rate is 75 Hz when system
frame rate is set to 50 Hz)
1600 x 1200 / 60 Hz,
1920 x 1200 / 60 Hz (Reduced Blanking)
* Conforms to VESA DMT Version 1.0 Revision 10
Windows (R) Bitmap File (.bmp)
* Maximum 1920 x 1200 pixels,
24 bit per pixel, uncompressed
Input/Output Level and Impedance
Composite
Analog HD/RGB
1.0 Vp-p, 75 ohms
0.7 Vp-p, 75 ohms (H, V : 5 VTTL)
Input Connectors
Analog Video SD
Analog RGB
SDI
(3G/HD/SD)
DVI-I/HDMI
HD
Composite (BNC type) x 4
* Select Composite or SDI using menu per channel
Component (HD DB-15 type) x 4
* Combined use with Analog RGB
HD DB-15 type x 4
* Combined use with Analog HD (Component)
* Select DVI-D/HDMI or Analog RGB using menu
per channel
BNC type x 4
* Conforms to SMPTE 424M, 292M, 259M-C
DVI-I type x 4
* Select DVI-A or DVI-D/HDMI using menu per
channel
Output Connectors
Analog Video
Analog RGB
SDI
(3G/HD/SD)
DVI-D/HDMI
Other Connectors
TALLY
Remote
REFERENCE
USB port (host)
Effects
Transition
Composition
Others
Others
Power Supply
Power Consumption
Dimensions
Weight
Accessories
SD
HD
Composite (BNC type) x 1
Component (HD DB-15 type) x 1
* Combined use with Analog RGB
* Progressive only
HD DB-15 type x 1
* Combined use with Analog HD (Component)
BNC type x 2
* Conforms to SMPTE 424M, 292M, 259M-C
DVI-D type x 2
HDMI x 1 (for multi-view monitor)
HD DB-15 type x 2
* Input (max): 12 V, 200 mA Open collector Type
MIDI : 5 pin DIN type (IN, OUT/THRU)
RS-232C : D-Sub 9 pin type x 1
BNC type (IN, THRU)
* Black Burst (Sync to frames), Bi-Level, Tri-Level Sync
A type x 1 (for USB memory)
Cut, Mix, Wipe (9 patterns)
PinP, DSK, Chroma Key, Luminance Key, External Key
Output Fade, Output Freeze
AC 115 V, AC 117 V,
AC 220 V, AC 230 V, AC 240 V (50/60 Hz)
75 W
482 (W) x 274.6 (D) x 115.9 (H) mm
19 (W) x 10-13/16 (D) x 4-9/16 (H) inches
* When rack mount angles are fitted. 6U size.
5.5 kg / 12 lbs 3oz
Power Cord, Rack Mount Angle (2),
Input Template, Owner's Manual
* When Sync Reference is set to [External], the resolution of 800 x 600 and refresh rate of 60 Hz are no longer compliant with the VESA standard.
This means that display on some devices may not be possible in this situation.
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
Name Plate
A name plate bearing the power consumption, model name, and serial number of this product is attached at the location shown below.
fig.name-plate.eps
52
Appendices
About Remote Control
The V-800HD supports remote control via MIDI and the RS-232C interface, enabling you to operate the unit remotely from an external device. When performing remote control, download “Remote Control Guide” from the following Roland website.
http://www.rolandsystemsgroup.net/ fig.MVC-logo.eps
The V-800HD can be operated remotely from a device that supports MIDI Visual Control. MIDI Visual Control is a feature that uses
MIDI to link visual expression to a musical performance.
About Rack Mounting
About Rack-mount Angles
When using the unit installed with the rack-mount angles, remove the screws at the locations shown in the figure below (at 3 locations on each side, for a total of 6) at first and install the angles with original screws.
fig.angle-screws.eps
When installing or detaching the rack-mount angles, give attention to the following precautions.
• Before removing any screws, turn off the power to the V-800HD and detach the power cord and all connection cables.
• Be sure to block the screw holes with the removed screws.
• Never use any screws except the removed ones to block the screw holes. Using other screws may cause malfunction.
• When installing the rack-mount angles, turn off the power to the V-800HD and detach the power cord and all connection cables. Also, be sure to install using the original screws.
Mounting in a 19-inch Rack
When mounting the unit in a rack, observe the following precautions.
• The video fader protrudes beyond the mounting surface of the rack. Take care not to damage it when mounting the unit.
• To prevent incorrect operation or malfunction, take care not to subject areas protruding beyond the rack to accidental impact.
• To ensure room for connectors and cables as well as space around the ventilation ports, ensure 2U of clearance above the unit.
• Before mounting, turn off the power to the V-800HD and detach the power cord and all connection cable.
• Use all threaded holes (at 4 locations on each side, for a total of 8) to secure the unit to the rack using screws. (Screws for rack-mounting are not included.)
• When mounting the unit in the rack, use due caution to ensure that your fingers do not get caught or pinched between a rack-mount angle and the rack.
About the Input Template
The included input template indicates the factory-default correspondences between cross-points and input channels. Use it attached at the location shown below.
fig.input-template.eps
53
Appendices
Troubleshooting
Nothing is displayed on the multi-view monitor.
Does the connected monitor support a resolution and refresh rate of 1920 x 1080/60 Hz (progressive)? Nothing is displayed if the monitor is not compatible. Also, nothing is displayed if the monitor does not support HDCP signals.
Composite input is not output.
Is the source at the connected channel set to composite? In the factory-default state, SDI input is assigned to channels 1 through 4.
The assignment must be changed to composite input (p. 21).
Analog RGB input is not output.
Is the source at the connected channel set to analog RGB? In the factory-default state, DVI/HDMI input is assigned to channels 5
through 8. The assignment must be changed to analog RGB input (p. 23).
* The same operation is also necessary when using a conversion cable to make an analog component connection.
DVI input is not output.
Is the switch at the connector set to the correct position ([DVI-A] or [DVI-D])? The signal cannot be detected if this is not set correctly.
Nothing is output from the SD OUT connector, SDI OUT connectors, or RGB/COMPONENT OUT connector.
Has the setting for inputting HDCP signals been made? When [HDCP] at the System menu is set to [ON], output from the SD OUT connector, SDI OUT connectors, and RGB/COMPONENT OUT connector stops.
* Note, however, that output from the DVI-D/HDMI OUT connectors and output to the multi-view monitor continues.
No still image can be assigned to an output fade.
Is the still image assigned to channel 10? A still image cannot be assigned to channel 10 and output fade at the same time. When assigning a still image to an output fade, change the channel-10 assignment to a color background.
Compositing with DSK is not possible.
A USB memory device cannot be used.
Has the USB memory device been formatted on the V-800HD? A USB memory device that has not been formatted on this product cannot be used. Also, operation has been tested for commonly available USB memory devices, but operation of all USB memory devices is not assured. Depending on the manufacturer and type of the USB memory device, correct operation may not be possible.
Still-image data cannot be imported.
contains no more than eight single-byte alphanumeric characters and the file extension (.bmp) is present.
Switching is not complete even when the video fader is moved.
Perform calibration of the video fader. Move the video fader all the way and calibrate .T execute calibration, select [Video Fader
Calibrate] in System menu.
Startup takes a long time.
The panel indicators are too bright/dark.
Carry out dimmer adjustment. At the System menu, raise or lower the value of the [LED Dimmer] value. Even if you raise/lower this value, the brightness of the LEDs around [VALUE] dial etc. will be unchanged.
54
Dimensions
fig.dimensions.eps
445.1
436
482
465
Unit : mm
57.1
265.4
76.2
5˚
57.1
37.5
115.9
Appendices
55
V-800HD Version 1.50 Added Functions
The following features were added to V-800HD version 1.50.
For information about version1.50 software, download from the following Roland website.
http://www.rolandsystemsgroup.net/
Supports 3G-SDI Level B Mapping Structure
• The V-800HD ver. 1.5 supports level B mapping structure of 3G-SDI (1080p50Hz, 1080p59.94Hz).
• The 3G-SDI mapping structure of the input signal is detected automatically.
• The mapping structure of 3G-SDI output signal can be selected using the menu.
Menu Items Setting Value
Output -> Format Main -> 3G-SDI Mapping Level A, Level B
Sync with Input Video Signal
• The V-800HD ver. 1.50 can synchronize with SDI input as reference.
• You can select a reference SDI input.
Menu Items Setting Value
System -> Reference Internal, External, Input SDI 1, ... Input SDI 4
• The output vsync of the V-800HD synchronizes with the input signal when the value of System -> Reference is Input SDI 1, ...
Input SDI 4. In this case, the system latency is minimized. If you want to synchronize the input/output fields, execute the settings below.
Turn the Field Sync Processing of System to ON
Although the processing time increases, the input/ output fields match automatically.
Adjust the value of Reference Line Adjust in System
Although the input/output phases differ, you can minimize the latency keeping the synchronization of input/output fields.
Field Sync Processing
• While the V-800HD input/output interlaced signals, synchronization of fields is possible.
Menu Items Setting Value Explanation
System -> Field Sync Processing
ON
Enables the field sync processing.
The fields of input/output match and this improves the image quality.
However, the processing time increases.
OFF
A/B Mode Switching
• You can select A/B mode for video switching.
Menu Items
System -> Panel Operation
Setting Value
PGM/PST, A/B
• PGM/PST is the default mode.
• Regardless to the PGM section or PST/EFFECT section of cross-points, PGM is determined by the video fader position. The indicator of the PGM output channel lights in red. The indicator of the PST output channel lights in green.
• While you are compositing images, the indicator of background channel lights in red. The indicator of foreground channel lights in green.
56
V-800HD Version 1.50 Added Functions
AUX Output of the Input Signal
• You can directly send the input channel signal to the AUX bus. However, you cannot use DSK while you are selecting input signal
• Use menu to select the channel to be sent to AUX bus.
Menu Items Setting Value
Output -> AUX Source
Mixer Input, Mixer Output, DSK Source,
DSK Output, Input CH.1, ... Input CH.10
Selection of the Recalling Parameter
• You can select the parameters to recall when you operate the MEMORY buttons.
Menu Items Setting Value Explanation
System -> Memory Recall Parameters ALL
Cross-point
This recalls all the parameters (same as previous version)
This recalls the parameters below only.
- Channel selection
- Key setup
- PinP setup
- DSK setup
- Wipe setup
- Input connector selection
Automatic Memory Save
• If this is turned on, the current status of the V-800HD is saved to memory 1-1 automatically. The status is loaded at next booting and the status returns.
Menu Items Setting Value
System -> Auto Memory ON, OFF
• The auto saving is carried out when you operate any menu cursor. Auto saving does not work when cross-point buttons or video fader is operated.
Expanded Color Correction Range
• The range of color correction is expanded.
Menu Items
Output -> Format Main -> Color Correction
Brightness
Contrast
Saturation
Setting Value
-128
- +127
-128
- +127
-128
- +127
Fine Adjustment of Chroma Key HUE
• The extraction color was fixed to blue or green in previous version. Now it’s possible to fine adjust the color.
Setting Value Menu Items
Key -> Hue
Fine
Width
-128
- +127
-128
- +127
• Width is same as Hue adjustment of previous version.
57
V-800HD Version 1.50 Added Functions
Supports Multi-view monitor not compatible with HDCP
• As the multi-view monitor, now you can connect HDCP non-compatible product.
• However, of HDCP of the V-800HD is turned on, the multi-view screen is filled with plain blue. It can display the menu screen only.
Version Number Display
• You can check the version number in System menu of the V-800HD.
The memory saved settings is not compatible with the previous version. At the first booting after update, factory reset is executed automatically.
58
59
Index
A
C chroma key ..................................................................................... 37
Clock Source .................................................................................. 24
Component ............................................................................. 19, 22
Composite ............................................................................... 19–20
Compositing ........................................................................... 14, 35
Cross-Points ............................................................................ 14, 49
D
E
External Key .................................................................................... 38
F
Factory Reset ................................................................................. 50
Final Output ................................................................................... 34
H
I
INPUT STATUS ............................................................................... 14
L
luminance key ............................................................................... 37
M
Main Output ................................................................................... 27
MEMORY ................................................................................... 15, 43
menu ................................................................................................ 10
Multi-view Monitor ......................................................................... 9
O
OUTPUT FADE ........................................................................ 15, 34
P
PGM Section ...................................................................................... 9
Picture-in-Picture ......................................................................... 35
PVW Section ...................................................................................... 9
R
REFERENCE ..................................................................................... 17
S
Source Monitors .............................................................................. 9
T
TRANSITION .................................................................................... 15
Transition Effects .......................................................................... 31
U
V
Video Fader ..................................................................................... 15
W
WIPE PATTERN ............................................................................... 15
60
This product complies with the requirements of EMCD 2004/108/EC and LVD 2006/95/EC.
For EU Countries
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
To assure continued FCC emission limit compliance, use only shielded interface cables when connecting to other device.
Any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment.
For Canada
NOTICE
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil num rique de la classe A respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada.
For C.A. US (Proposition 65)
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For China
For EU Countries
ES
PT
NL
DK
NO
LV
SI
GR
EE
LT
PL
CZ
SK
SE
FI
HU
UK
DE
FR
IT
For EU Countries
This product is intended for use in the following Electromagnetic environments:
E1: residential, E2: commercial and light industrial, E3: urban outdoors, E4: controlled EMC environment, ex. recording studio (broadcasting studio) which are specified in EN55103-1 and EN55103-2.
* 5 1 0 0 0 2 9 1 0 1 0 3 *
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project