Lifetime Limited Warranty
Lifetime Limited Warranty ConvaQuip Ind., Inc warrants the frame of product to be free from defects in materials or workmanship for a period of lifetime from date of purchase. If, within the specified warranty period, this product is proven to be defective, it will be repaired or replaced at ConvaQuip Ind., Inc option. This warranty does not cover shipping costs incurred in replacement or repair of this product. ConvaQuip stands firm on our commitment to providing the highest quality products, as well as exceptional service. This product was built to precise standards and thoroughly inspected prior to shipment. This Lifetime Limited Warranty represents our confidence in the materials and workmanship of our products. For warranty service, please contact the dealer from whom you purchased your ConvaQuip product. In the event that you do not receive satisfactory service, please call us directly at the number below. Be prepared to indicate the nature of the defect, the product serial number, and the name and location of your dealer. You will also be required to provide a receipt of your purchase. DO NOT return any products to our office without prior consent. This warranty does not cover problems due to user negligence or misuse of the product. This warranty shall not extend to non-durable components, including, but not limited to rubber tips, hand grips, casters, brakes, and other parts subject to normal “wear and tear”. These items are covered for a period of 90 days. THIS FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, IMPLIED WARRANTIES, IF ANY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. CONVAQUIP SHALL NOT BE LIABLE FOR ANY SEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER. Bariatric Tub Transfer Bench INSTRUCTIONS & WARRANTY Height Adjustable Tool-Free Assembly Holds up to 500 lbs. MANUFACTURED IN CHINA FOR: ConvaQuip Ind., Inc P.O. Box 3417 Abilene, TX 79604 INSTRUCTIONS FOR USE SAFETY GUIDELINES PLEASE READ BEFORE USE Back Support Platform Support Arm CAUTION: Transfer benches should be adjusted to a height above the wall. CAUTION: When removing a transfer bench from the tub, always release the suction cups by pinching the two tabs together. Height Adjustment Tip Suction Cup MAINTENANCE: 1. Use a soap and water solution, rinse with clean water, then dry with a soft cloth. 2. Never use organic solvents, abrasive cleaners or scouring pad on any part of the tub transfer bench. 3. Check fit and tightness of all nuts, bolts and knobs on a weeklt basis to ensure tub transfer bench is safe to use. Model 1731 Weight Capacity : 500 lbs. Note: seat color may vary. Assembly Instructions SET-UP: 1. Remove frame, back, support arm and legs from box. 2. Insert support arm into frame until support arm buttons protrude fully through guide holes. 3. Place frame on side on a working surface. 4. Locate channel guides (4 each) on underside of seat. Align seat support tubes with channel guides. 5. Slide seat support tubes through channel guides until seat support tube buttons protrude fully through channel guide holes. 6. Attach suction cup legs to frame on same side as support arm. Attach flange tips to frame legs on opposite sides of frame. from supoort arm. 7. Adjust seat height as directed in height adjustment section. HEIGHT ADJUSTMENT: 1. Depress the height adjustment button and slide the lower leg upward or downward until the height adjustment button is fully engaged in the desired hole. 2. Repeat for the other legs. NOTE: Legs inside the tub may be adjusted to a different height than the legs outside the tub. However, the legs inside the tub should be adjusted to the same height, and the legs outside of the tub should be adjusted to the same height. Safety Precautions DO NOT ATTEMPT TO ADJUST OR OPERATE TRANSFER BENCH WITHOUT READING ALL INSTRUCTIONS CAREFULLY. * Make certain that the height adjustment snap buttons fully protrude through the same respective holes of each leg extension. This will ensure that the leg extensions are securely locked in position ans an even height is achieved. * Ensure ALL screws, nuts and/or bolts are tightened. * Check all the rubber tips on the leg extensions for rips, wear or if they are missing. Immediately replace any or all if any of these imperfections exist. * All floor leg extensions with rubber tips MUST touch the floor simultaneously at all times. * DO NOT stand on transfer bench. * ConvaQuip Ind., Inc. assumes no responsibly for any damage or injury caused by improper installatio, assembly or use of this product.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project