advertisement
M I T E L
5320/5330/5340
IP Phone User Guide
5320/5330/5340 IP Phone Quick Reference Guide
This guide provides information for frequently used features. For more information about these and other features, refer to the user guide. For voice mail information, refer to the voice mail user guide for your system.
Feature Buttons
Most of the following feature codes work when your IP phone is idle. However, if you are on an active call or if the IP phone is off-hook, you may need to press
(Special) to activate the feature before you enter the feature code.
If you make a mistake when entering numbers or characters, you can press (Hold) to move the cursor to the left and delete the characters entered, or you can press
*
to cancel the feature.
Button Action
(Up)
(Down)
(Speaker)
(Mute) Mutes the microphone during a call.
(Applications) Activates the Applications menu to use the conference unit or cordless devices, program various phone settings, and enable Clean Mode.
(Special)
Activates features while on a call.
The (Special) button does not cancel features. To cancel features, press the Star button
(*).
(Redial)
Provides volume control.
Scrolls through feature options.
Activates Handsfree Mode.
Activates features.
(Hold)
(Transfer)
(Message)
Calls the last external number dialed. You cannot redial internal numbers.
Places the current call on hold.
Left/Backspace when entering dialpad characters.
Transfers the current call.
Right/Forward when entering dialpad characters.
Allows you to view station messages.
Toggles between Alpha Mode and Numeric Mode.
Commonly Used Feature Codes
Contact your system administrator for more information about system features.
Feature
ACD Agent – Log In/Out
Automatic IC Call Access – On/Off
Automatic Trunk Call Access – On/Off
Background Music – On/Off
Call Forward – All Calls
Call Logging
Conference
Default Station
Directory
Display Time And Date
Do-Not-Disturb – On/Off
Dynamic Extension Express – On/Off
Dynamic Extension Express Handoff
Handsfree – On/Off
Headset – On/Off
Hold – Individual
Hold – System
Hunt Group – Remove/Replace
Message – Cancel Left Message
Message – Delete Message
Message – Leave Message
Message – View Messages Menu
Microphone Mute – On/Off
Page Receive – On/Off
Program Buttons
Program Station Password
Programmable Buttons – Default
Queue (Callback) Request
Record-A-Call
Reverse Transfer (Call Pick-Up)
Ring Tone Selection
Station Speed Dial
Station Speed Dial – Programming
Switch Keymap
System Forward – On/Off
System Speed Dial
View Button Assignments
Code
385
4
398
382
397
392
395
6
383
399
354
381
396
367
365
314
325
335
324
366
368
388
319
317
336
307
300
372
364
355
333
5
394
328
361
360
313
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Answering Calls
Lift the handset, or press (Speaker) to answer a call while using a headset or to answer a call in Handsfree Mode.
Placing Emergency Calls
Dial the emergency number (911 U.S. or
999/112 Europe). The system immediately places the emergency call as soon as you dial the number, even if you do not select an outside line.
Placing Internal (Intercom) Calls
With or without the handset lifted, dial the extension number. If you enter incorrect digits, you can press (Hold) to move the cursor backward, deleting the last digits entered. If you are using Handsfree Mode, listen for the double tone, and then begin to speak.
Placing External Calls
Press the Outgoing button, an unlit Call button, or enter the Outgoing Call access code (8 is the default code), and then dial the number.
Redialing External Numbers
With or without the handset lifted, press the
(Redial). The system automatically selects a line and dials the number.
Transferring Calls to Other Extensions
1. While on the call, press (Transfer), and then enter the extension number.
2. Do one of the following:
•
Wait for an answer, announce the call, and then hang up. If the extension is unavailable, press the flashing IC or Call button to return to the caller.
•
Hang up to transfer the call and disconnect the call from your IP phone.
Forwarding Calls
1. Press the Fwd button, and then enter the feature code, if applicable. ENTER FORWARD DEST appears.
2. Enter the extension number, or press the
Outgoing button or enter the Outgoing Call access code (8 is the default code), and then dial the telephone number.
Placing Conference Calls
1. While on the first call, press the Conf button to place the call on hold. CALL NEXT PARTY TO
CNF appears.
2. Place a call to the next conference party. For external calls, press the Outgoing button or enter the Outgoing Call access code (8 is the default code), and then dial the number.
3. After the party answers, announce the conference, and then press the Conf button to place the call on hold. If necessary, repeat this step to add the remaining conference party.
4. Press the Conf button again to start the conference. CNF IN PROGRESS appears.
Viewing and Responding to Messages
1. With the handset on-hook, press (Message) or the VIEW MESSAGE menu button (5340 IP
Phones only). Messages are displayed as first in/ first out. If there is more than one message, you can repeatedly press (Message) to scroll through the messages.
2. When the desired message is displayed, press #, or lift the handset for privacy, and then press # to respond. (If your handset is off-hook and you press [Message], you automatically place a call to the party or message center who left the message.)
Using Do-Not-Disturb
1. Press the DND button, and then do one of the following:
•
Press (Up) or through the messages.
(Down) to scroll
•
Enter the two-digit number for the DND message.
2. If applicable, enter the additional text for the
DND description.
3. Press handset.
(Speaker), or lift and replace the
Placing a Page Announcement
1. Press 7.
2. Enter the page-zone number (0 to 9).
3. After the tone, make your announcement, and then hang up.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Notice
This guide is released by Mitel Networks Corporation and provides information necessary to use the
5320/5330/5340 IP Phones. The guide contents, which reflect current Mitel standards, are subject to revision or change without notice.
Some features or applications mentioned may require a future release and are not available in the initial release.
Future product features and applications are subject to availability and cost. Some features or applications may require additional hardware, software, or system administrator assistance.
For sales, service, or technical support, contact your local authorized provider:
Enter provider information above.
If you do not know the contact information for your local provider, use the “Partners” link at the top of the Mitel home page (www.mitel.com) to find a location near you.
If you have any questions or comments regarding this user guide or other technical documentation, contact the
Technical Publications Department (USA) at:
Mitel
®
is a registered trademark of Mitel Networks Corporation.
All other trademarks mentioned in this document are the property of their respective owners, including Mitel Networks
Corporation. All rights reserved.
© 2008-2010 Mitel Networks Corporation
Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from Mitel.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page i
Important Safety Instructions and Precautions
Remember the following safety guidelines when using the IP phone.
Programming Emergency Numbers
Make sure to do the following when programming emergency numbers and/or making test calls to emergency numbers:
•
Remain on the line and briefly explain to the dispatcher the reason for the call.
•
Perform tests during off-peak hours such as early morning or late evenings.
Safety Notices
The following notices may appear on the product or in the technical documentation.
Notice Description
Caution indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or damage to the equipment or property.
Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
The exclamation point within an equilateral triangle indicates that important operating and maintenance (servicing) instructions are included in the literature accompanying the product.
Maintenance and Repair
There are no user serviceable parts inside the IP phone. For repairs, return the IP phone to an authorized Mitel provider.
NOTE
Changes or modifications not expressly approved by Mitel may void the user’s right to operate the equipment.
Page ii
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Power Requirements
CAUTION
Phone Damage Hazard. To avoid damaging the IP phone, make sure the IP phone is connected to the proper power supply before powering on. Contact your system administrator for more information.
The IP phone requires any one of the following power supplies:
•
Mitel 48-volt DC Ethernet power adaptor 100-240 volt AC 50-60Hz (ES), part number 50005301
•
An industry-standard IEEE 802.3af Power over Ethernet (PoE) power supply unit
If your IP phone uses a centralized PoE power supply unit, do not use the 48-volt DC Ethernet power adaptor. If necessary, contact your system administrator for assistance before connecting your IP phone to the centralized power source.
Make sure the IP phone is plugged into an uninterruptible power supply (UPS). If your IP phone is plugged into the
UPS and the power fails, it should remain powered on for about 10 minutes. If the IP phone is not plugged into a UPS and the power fails, the current call is dropped and you will not be able to use the IP phone until the power is restored.
Software Updates
CAUTION
Phone Damage Hazard. Do not use your IP phone or disconnect it from the power supply while it is updating software.
The IP phone may require occasional software updates when new versions are available. The IP phone is configured to download the updates automatically. Contact your system administrator for more information.
Product Disposal Instructions
This symbol indicates that the product is classified as electrical or electronic equipment and should not be disposed of with other commercial or household waste at the end of its working life. For appropriate disposal and recycling instructions, contact your local Mitel provider.
The Waste of Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC) was established by the European Union to minimize negative impact on the environment, control hazardous substances, and curtail landfill expansion by using the best available recovery and recycling techniques.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page iii
Phone Usage
This equipment is not for connection to the telephone network or public coin phone service. It is only for use when connected to Mitel systems.
WARNING
When using your IP phone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
•
Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
•
Avoid using a phone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
•
Do not use the IP phone to report a gas leak in the vicinity of a leak.
•
Do not connect directly to the Public Switched Telephone Network (PSTN). Any connection of this phone to an off premise application, an out of plant application, any other exposed plant application, or to any equipment other than the intended application may result in a safety hazard, and/or defective operation, and/or equipment damage. “Exposed plant” means where any portion of the circuit is subject to accidental contact with electric lighting or power conductors operating at a voltage exceeding 300 volts between conductors or is subject to lightning strikes.
•
The socket outlet, if used, shall be located near the equipment and shall be easily located by the user.
•
Use only Mitel approved power adaptors. See “Power Requirements” on page iii
.
•
The handset supplied with the IP phone is not certified for use with any other phone. Use of the handset with any other phone may have the potential to cause hearing loss in the event of a lighting strike on the outside plant wiring.
Page iv
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Notice to Canadian Customers
The Class B digital apparatus complies with Canadian ICES-003.
Notice to U.S. Customers
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Notice to European Customers
We, Mitel Networks LTD.
Of, Mitel Castlegate Business Park
Portskewett
Caldicot
NP26 5YR
UK
Declare that for the hereinafter mentioned product the presumption of conformity with the applicable essential requirements of
DIRECTIVE 1999/5/EC OF THE EUROPEAN
PARLIAMENT (RTTE DIRECTIVE) AND OF THE COUNCIL is given.
Mitel IP Phones: 5320/5330/5340
Any unauthorized modification of the product voids this Declaration.
For a copy of the original signed Declaration of Conformity (in full conformance with EN45014), please contact the Regulatory
Approvals Manager at the above address.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page v
Contents
Contents
Getting Started 1
Personalizing Your Phone 15
Page vii
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Contents
Answering and Placing Calls 31
Page viii
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
Contents
41
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page ix
Contents
Messages 59
Hunt Groups 65
Cordless Devices 71
Page x
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Contents
Troubleshooting 79
Index 83
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page xi
Getting Started
Getting Started
Welcome
The instructions in this guide are for using the Mitel 5320/5330/5340 Internet Protocol (IP)
Phone on the Mitel 5000 Communications Platform (CP). The Quick Reference Guide located at the beginning of this guide is an overview of frequently used features.
Your IP phone should be powered on and ready to use. If the display is blank, or if the display name, extension number, or time or date are incorrect, contact your system administrator for assistance.
Because a variety of voice mail products work with the 5000 CP, this guide does not include voice mail instructions. For voice mail instructions, refer to the voice mail user guide for your system. For example, refer to the Enterprise Messaging, Basic Voice Mail, and Embedded
Voice Mail Card User Guide, part number 835.3205, or the Mitel NuPoint Unified Messaging
User Guide on the Mitel Web site (http://edocs.mitel.com). Contact your system administrator for more information about your voice mail system.
NOTE
Because many phone features can be programmed to perform various tasks, some features may work differently than the descriptions in this guide. Contact your system administrator for more information.
About Your IP Phone
The IP Phones are full-feature, dual port phones that provide voice communication over an IP network. All phones have a 160 x 320 (pixels) liquid crystal display (LED), self-labeling programmable buttons, on-hook dialing, and a Ring/Message Indicator.
For one-touch feature access, the 5320 IP Phone has 8 programmable buttons, the 5330 IP
Phone has 33 programmable buttons, and the 5340 IP Phone has 42 programmable buttons.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 1
Getting Started
5320/5330 IP Phone Features
The 5320 and 5330 IP Phones are shown here.
1
See “5320/5330 IP Phone Features” on page 2 for more information about the IP phone features.
5320 IP Phone
1 2 3 4
8
6
5
5330 IP Phone
1 2 3
7
4
Page 2
8
6
5
1 – Handset (see
2 – Programmable buttons (see
1
3 – Display (see
2
4 – Ring/Message Indicator (see
)
7
5 – Feature buttons (see page 5
)
6 – Dialpad buttons (see page 5 )
7 – Navigation buttons (see
8 – External Speaker (see
1. The top three buttons on the 5320 IP Phone do not have LEDs.
2. The 5320 IP Phone does not have a backlit display.
1. These images are examples of how your IP phone may be programmed.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Getting Started
5340 IP Phone Features
The 5340 IP Phone is shown here.
2
See ““Phone Feature Descriptions” on page 4
” for more information about the IP phone features.
1 2 3
4
9
8
7
1 – Handset (see
2 – Display (see
)
6 – Dialpad buttons (see page 5
)
7 – Programmable buttons (see page 6
)
8 – Navigation buttons (see page 6
)
4 – Ring/Message Indicator (see
page 4 ) 9 – External Speaker (see
5 – Feature buttons (see
)
6
5
2. This image is an example of how your IP phone may be programmed.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 3
Getting Started
Phone Feature Descriptions
The following sections describe default configurations. Your IP phone may be programmed
differently. Contact your system administrator for more information. See “5320/5330 IP Phone
Features” on page 2 and “5320/5330 IP Phone Features” on page 2
for phone feature locations.
Handset
The handset provided with this equipment is hearing aid compatible (HAC). If you are using a headset or if you are in Handsfree Mode, you do not need to use the handset. See “Using
Handsfree Mode” on page 41 for more information.
Display
The display provides a 160 x 320 (pixels) high-resolution viewing area for selecting and using features and identifying callers. When idle, the display shows user information, the system time and date, and feature button assignments. Consider the following when using the display:
•
The 5320 IP Phone does not have a backlit display.
•
You can adjust the display Contrast and Brightness levels (see page 16 ).
•
You can control the size of the text that appears on the display for programmable buttons
(see
).
5330 and 5340 IP Phones include an embedded screen saver that you can configure for your display. Configuration options include the screen saver timeout, display image, and brightness options (see
).
Ring/Message Indicator
The Ring/Message Indicator flashes or stays lit to indicate call, message, and feature activity.
For more information about messaging features, see “Messages” on page 59 . Ring/Message
Indicator signals are described in the following table.
Indicator Signals
Rapidly flashing
Slowly flashing
On
Off
Description
You have an incoming call.
You have a waiting message or callback message.
You are on a call or using a feature.
Your IP phone is idle.
Speaker
The speaker provides audio for handsfree calls and background music. See “Using Handsfree
Page 4
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Getting Started
Feature Buttons
Feature buttons provide quick access to commonly used features. See the following table for descriptions.
Button Action
(Up) or (Down Provides volume control for the ringer, handset, and speaker.
Scrolls through feature options.
(Speaker) Activates Handsfree Mode/speakerphone (see
Activates features.
).
(Mute) Temporarily turns off your microphone during a call.
(Applications)
(Special)
(Redial)
Activates the Applications menu to perform the following options:
•
Use the conference unit (see page 9
)
•
Program the following settings in the Settings application:
o Change the language on the display (see page 17 ).
o Change the text size on the display (see page 18 )
o Adjust the display brightness (see page 16 )
o Use the screen saver (see
)
o Specify audio feedback options (see page 21
)
o View phone information (see page 8
)
•
Use cordless devices (see page 71 )
Activates features while on a call. The (Special) button does not cancel features. To cancel features, press the Star button (
*
).
Calls the last external number dialed. You cannot redial internal numbers.
(Hold)
(Transfer)
(Message)
Places the current call on hold and retrieves a call from hold.
Left/backspace when entering dialpad characters (see
Transfers the current call.
Right/forward when entering dialpad characters (see
).
Displays station messages.
Toggles between Alpha Mode and Numeric Mode when entering dialpad characters.
Dialpad Buttons
Use the dialpad buttons to dial phone numbers, enter feature codes, and to enter characters when using features that require text input.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 5
Getting Started
Programmable Buttons
The IP Phones have self-labeling, programmable buttons. The 5320 IP Phone has 11 programmable buttons. The 5330 IP Phone has 33 programmable buttons. The 5340 IP Phone has 42 programmable buttons. Each phone has the following buttons that are programmed by the system administrator and cannot be reprogrammed; however, you can program the remaining buttons for quick access to features or speed-dial entries. See “Using Programmable
Buttons” on page 24 .
Button
Do-Not-Disturb
Outgoing
Call 1
Call 2
Intercom
Conference
Forward
Action
Turns Do-Not-Disturb (DND) mode on or off.
Selects an outgoing line for external calls.
Selects an outside line or answers a call.
Selects an outside line or answers a call.
Answers an intercom (internal) call.
Places a conference call.
Forwards the call to the specified number.
Menu Buttons (5340 IP Phones only)
The 5340 IP Phone has eight dynamic menu buttons at the top of the Display that change depending on the feature and menu currently displayed. You can use the menu buttons to view and select feature options.
Navigation Page Buttons
The IP Phones have three Navigation Page icons located in the bottom right hand corner of the display to navigate between the IP phone’s three display pages. When a page icon in the bottom right-hand corner of the Display blinks, it means that there is real-time activity on the page where the number or feature is located.
If you navigate to the second or third pages, you must use the Navigation Page buttons to return to the first page. You are not automatically returned to the first page after using features or when the IP phone is idle. You can also press the (Home) button on the 5340 IP Phone
(only) to return to the first page.
External Speaker
The speaker provides audio for handsfree calls and background music. See “Using Handsfree
Page 6
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Getting Started
Phone Signals
The IP Phones have several audio and visual signals to indicate feature activity. The following are a few helpful tips:
•
Lit or blinking buttons indicate call or feature activity.
•
All phone button lamps illuminate at the same time for a few seconds when the IP phone is reset or powered on.
•
The following actions may cause an error tone: o Pressing an invalid button combination. o Selecting a restricted feature. o Dialing a restricted or invalid number. o Dialing too slowly between digits. o Waiting too long before performing the next step.
To correct an error tone, hang up and try again.
•
Many features “time-out” if you wait too long before performing the next step. If this happens, you must start over.
•
“Off-hook” means the handset is lifted. “On-hook” means the handset is in the cradle.
•
If your IP phone does not have a lamp under the speaker button, the large message indicator lamp on the top right of the IP phone indicates that the speakerphone is in use.
Comfort and Safety Tips
Observe the following comfort and safety tips when using the IP phone:
•
Do not cradle the handset: Prolonged use of the handset can lead to neck, shoulder, or back discomfort, especially if you cradle the handset between your neck and shoulder. If
you frequently use the IP phone, you might find a headset more comfortable. “Using a
.
•
Adjust the viewing angle: The built-in stand tilts to give you a better view of the buttons.
See “Adjusting the Viewing Angle” on page 15 .
•
Protect your hearing: Because prolonged exposure to loud sounds can contribute to hearing loss, keep the volume at a moderate level. You can adjust the volume levels of the handset receiver or headset. See “Changing Volume Levels” on page 16 .
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 7
Getting Started
Viewing the Phone Information
You can use the phone to view system or phone information.
To view system information:
the following appears.
Using a Headset
When using a headset, press (Speaker) to connect to or disconnect from calls. The
Headset icon appears when the headset is in use. You cannot use the handset or speakerphone when the IP phone is in Headset Mode. Disconnecting the headset automatically enables the handset.
NOTES
The headset must be hearing aid compatible (HAC).
If your headset has a power-saver mode, make sure the system administrator has enabled the “Headset Connect Tone” feature. If this is not enabled, you may miss the first few seconds of an incoming call.
To connect and activate the headset:
1. Insert the headset jack into the Headset port located on the back of the IP phone.
317
(Headset on/off). HEADSET MODE ON appears.
NOTE
Because Headset Mode disables the handset and speakerphone, you must turn off Headset Mode before you can use the handset or speakerphone.
To turn off Headset Mode and activate the handset and speakerphone:
Dial 317 (Headset on/off). HEADSET MODE OFF appears.
Page 8
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Getting Started
Using the 5310 IP Conference Unit
Your IP phone can use the 5310 IP Conference Unit (shown below) for full-duplex, advanced IP conferencing. Use the Conference Controller touch screen to turn the Conference Unit on or off, to adjust the volume or to put the Conference Unit into Presentation mode. You can only run one Conference Controller session at a time. If the 5310 Conference Unit is not connected to your IP phone, the Conference Controller application is not available.
Installation instructions are included with the unit.
Mitel 5310 IP Conference Unit
5310 IP Conference Unit
For information about placing conference calls and adding parties to the conference, see
“Placing Conference Calls” on page 47 .
Accessing/Exiting the Conference Controller Application
You must first access the Conference Controller application to use the Conference Unit.
To access the Conference Controller application:
To exit the Conference Controller application:
Press Close in the Conference Controller application.
Turning the Conference Unit On and Off
The following instructions describe how to turn the Conference Unit on and off.
To turn the Conference Unit on and off:
Press Turn On or Turn Off in the Conference Controller application. If applicable, the icon appears in the IP phone status line while the Conference Unit is on.
NOTE
Turning the 5310 Conference Unit off terminates the active call. To continue the call either pick up the handset or press the Speaker button on the IP phone.
Adjusting the Conference Unit Volume
The following instructions describe how to adjust the Conference Unit volume.
To adjust the Conference Unit volume:
Press Volume Up or Volume Down.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 9
Getting Started
Muting the Conference Unit
You can mute the Conference Unit so that conversation or noise near the Conference Unit cannot be heard by individuals being conferenced.
To mute the Conference Unit:
Press Mute.
Placing the Conference Unit in Presentation Mode
Presentation Mode should be used when only one individual will be speaking into the
Conference Unit. If another individual near the unit wishes to speak, you should disable
Presentation Mode. Presentation Mode minimizes extraneous noise.
To enable/disable Presentation Mode:
Toggle Presentation Mode on or off in the Conference Controller application.
Page 10
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Getting Started
Using the Line Interface Module (LIM)
The LIM is an optional device that adds an analog phone line capability to your IP phone. In the event of a network failure, the IP phone can be configured to use the public switched telephone network (PSTN) to provide continued basic telephony until service in restored. The analog line can also be used for emergency calls and local calling.
Line Interface Module
Ethernet
Connection
Analog PSTN
Connection
You can use the LIM to:
• allow incoming and outgoing analog PSTN calls directly to and from the IP phone
• provide survivability (failover) in the event IP connectivity is lost
• provide emergency dialing support (emergency calls can be programmed to connect through the analog PSTN connection)
If you have a LIM connected to your IP phone, all programming of the LIM, except the Analog button (key), is done by the Installer when your IP phone is installed. To program the Analog button, see “Using Programmable Buttons” on page 24 .
The LIM operates in one of the following two modes, as determined by your System
Administrator:
•
LIM Mode: You can use the LIM line at any time.
•
Failover Mode: You can use the LIM line only when the IP connection has failed.
NOTE
Handsfree and on-hook dialing are not supported on the LIM line.
For information on emergency number dialing using the LIM, see “Placing Emergency Calls using the LIM Line” on page 33 .
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 11
Getting Started
Making and Answering Calls Using the Analog Button
To make a call using the Analog line:
2. Press the button you programmed as Analog Line. ANALOG CALL appears.
3. Dial the number.
NOTE
When you make an external call over the analog line, a prefix dialing number is not required. If your IP phone’s Analog Line button has the Privacy option enabled, you cannot access the analog line when another phone is using the analog line (button is solid orange).To access the analog line, the user of the other phone must first hang up. To determine whether the Privacy option is enabled, contact your System
Administrator.
To answer a Call using the analog line:
To answer a waiting call on the analog line:
NOTE
If you have subscribed to an analog call waiting service, you may use the hookswitch or press the Star button (
*
) to answer a waiting analog call. When you are on an analog call and a waiting analog call arrives, you hear a beep. This feature may not be supported in all regions.
To answer a waiting analog call or return to the original analog call:
1. Do one of the following:
•
Press and release the hookswitch.
•
Press the Star button (
*
) to cancel.
2. Press the button you have programmed as Analog Line.
To put a current call on hold to answer an incoming analog call:
Press the highlighted Analog Line button.
To switch between the current call and the held call when one of the calls is using the analog line, do one of the following:
•
If your current call is using the analog line, press the flashing Line button of the held call.
The analog call is automatically put on hold.
•
If your current call is using an IP line, press the highlighted Analog Line button. The IP line is automatically put on hold.
To end a current call when an incoming analog call arrives:
Press the Star button (
*
) and then press the highlighted Analog Line button. The current call ends and you are connected to the caller on the analog line.
To end the current analog call when an incoming call arrives:
Press the Star button (
*
) to cancel. The current analog call ends and you are connected to the new caller.
Page 12
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Getting Started
Making and Answering Calls Using the Failover Mode
To make a call using the analog line during an IP connection failure:
1. Lift the handset. IP FAIL: ANALOG CALL appears.
2. Dial the number.
To answer a call using the analog line during an IP connection failure:
Lift the handset. The call is answered. IP FAIL: ANALOG CALL appears.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 13
Personalizing Your Phone
Personalizing Your Phone
This chapter describes features you can use to personalize your IP phone.
Adjusting the Viewing Angle
You can tilt the IP phone stand for a better view of the buttons and display.
Press tabs on both sides to release and detach unit.
To adjust the viewing angle:
1. Turn the IP phone so it faces away from you.
2. Hold the base firmly, and then press the tabs on the sides of the stand to release and detach the base unit.
3. Hinge the hooks on the base unit into the notches on the back of the IP phone, and then snap into place as follows:
•
For a high-angle mount, hinge the two lower hooks into the bottom set of notches, and then snap the two upper hooks into the middle set of notches.
•
For a low-angle mount, hinge the two lower hooks into the middle set of notches, and then snap the two upper hooks into the top set of notches.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 15
Personalizing Your Phone
Changing Volume Levels
You can change the following volume levels:
•
Ringer (alerting tone)
•
Handset
•
Headset
•
Background music
•
External speaker
NOTE
Turning the external speaker volume down to the lowest levels may prevent you from hearing the feature “warning tones” that notify you when errors occur (for example, when you enter an incorrect feature code).
You must be using the feature to change the volume level. For example, if you want to change the handset volume level, you must be using the handset. However, you can adjust the ringer
(alerting tone) volume level when the IP phone is idle.
To change a volume level:
While using the feature, press (Up) to increase the volume, or press (Down) to decrease the volume. The volume level is automatically saved.
Changing the Ring Tone
You can select one of nine different ring tones.
To change the ring tone:
1. With the handset on-hook, dial 398.
2. Do one of the following to listen to (or turn off) ring tones:
•
Press 0 or the RINGER OFF menu button (5340 IP Phones only) to turn the ringer off.
•
Press (Up) or (Down) or 1 to 9 to listen to ring tones.
•
Press the PREVIOUS or NEXT menu button (5340 IP Phones only) to listen to and select a ring tone.
replace the handset to select the ring tone.
Adjusting the Display Contrast and Brightness
You can adjust the display Contrast and Brightness levels. (Brightness adjustment is available on models with backlit displays only.)
NOTE
By default, the IP phone display dims to 20 percent of the maximum brightness level after 5 minutes of inactivity (no button presses or audio, including background music). If the brightness is set at the lowest level, you may not notice when the display dims.
To adjust the Contrast or Brightness levels:
Page 16
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Personalizing Your Phone
Changing the Language
You can change the language to display text on your phone. Your system is programmed to support two of the following languages:
•
English
•
French
•
Spanish
To change the language on the display:
3. Press the language that you want to use.
NOTE
If your system administrator changes the language after the IP phone is already online, the new language option will not be displayed until the IP phone is restarted.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 17
Personalizing Your Phone
Changing the Text Size on the Display
You can control the size of the text that appears on the display for programmable buttons. This enhancement does not apply to the text size that appears on the display for the menu buttons.
Text size options include:
•
Large text: Provides one line of basic information for the features and functions programmed for the button. Large text is enabled by default.
•
Small text: Provides a first line of basic information and a second line of supplemental information for the features and functions programmed for the button.
The table below includes several examples for the large text and small text display options.
Programmable
Button
Station Speed Dial
Large Text
Example
Monica S
System Speed Dial
Chandler TS
Direct Station
Selection (DSS/
BLF)
Programmable
Feature
Intercom Call (IC)
Jessica A
DND
IC
Small Text
Example
Monica S
25598
Chandler TS
4809619000
Jessica A
28899
Second line provides...
The station speed-dial number programmed for the button.
The system speed-dial number programmed for the button.
The extension number programmed for the user.
DND
(372)
IC
Charlie B
The feature code that corresponds to the feature programmed for the button.
The name or number for the other party on the internal call.
To change the text size on a display:
Page 18
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Personalizing Your Phone
Using the Screen Saver
The IP Phones include an embedded screen saver that you can configure for your display.
By default the screen saver image is disabled. When your IP phone enters screen saver mode, only the IP phone’s backlight dims. All 5340 and newer 5330 IP Phones have a backlit display.
5320 IP Phones do not have a backlit display.
You can enable the screen saver image and when your IP phone enters screen saver mode, the
IP phone’s backlight dims and the embedded screen saver image, similar to the one below, appears on your display.
NOTE
The screen saver image is the same image you see when you press
(Applications) and select the About 5330/5340 IP Phone menu option.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 19
Personalizing Your Phone
To configure the screen saver on your IP Phone:
3. Configure your screen saver options: a. Select one of the following screen saver timeout options: o
15 minutes o o
10 minutes
5 minutes o
1 minute b. If desired, enable the Display Image option: o o
If you enable the Display Image option, the screen saver image appears and your backlight dims when your IP phone enters screen saver mode, as specified by the screen saver timeout setting.
If you disable the Display Image option, only your backlight dims (if your IP phone has a backlight) when your IP phone enters screen saver mode, as specified by the screen saver timeout setting. This is the default setting.
c. Configure brightness options if your IP phone has a backlight.
Options include: o o o
Brightness+: Increases the brightness of the display when your IP phone is in screen saver mode.
Brightness-: Decreases the brightness of the display when your IP phone is in screen saver mode.
Show Brightness: Shows the brightness level of the display when your IP phone is in screen saver mode. The display returns to normal after approximately two seconds.
To wake your IP phone from screen saver mode:
Lift the handset or press any button to wake the IP phone.
Page 20
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Personalizing Your Phone
Specifying Audio Feedback Options
The Audio Feedback setting allows you to adjust the volume of the audio feedback as well as the error beeps, and enable or disable the setting.
The error beep volume in the phone is related to the volume of the speaker. You can set the beep volume using this procedure; however, adjusting the speaker volume also affects the beep volume.
To adjust the volume of the audio feedback:
3. Set the audio feedback options for the button beep and error beep.
•
To turn audio feedback on or off, press or .
•
To adjust the volume level,
•
To play the beep, press Play button beep or Play error beep.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 21
Personalizing Your Phone
6
7
4
5
Button
1
2
3
8
9
0
M
P
G
J
A
D
1
:
T
W
0
Using the Dialpad Buttons to Enter Characters
N
Q
H
K
U
X
B
E
-
2
You can use the dialpad buttons to enter text or numbers for features such as Do-Not-Disturb
(see
) and Station Speed Dial (see page 36 ).
The following are guidelines when entering dialpad characters:
•
Press (Message) to switch from Alpha Mode to Numeric Mode. The (Message) button stays lit in Alpha Mode and is off in Numeric Mode.
•
Press (Hold) to move the cursor to the left and delete characters.
•
Press (Transfer) to move the cursor to the right.
•
In Numeric Mode, press # for a hyphen (-).
•
In Numeric Mode, press
*
for a colon (:).
•
Press #, (Speaker), or lift and replace the handset to save entries.
To use the dialpad to enter characters:
Press the dialpad buttons as shown in the following table.
O
R
I
L
V
Y
C
F
/
3
Dialpad Characters — American English and British English
Number of Times Dialpad Button is Pressed
,
4 5
.
6
; (
7
)
8 9
&
10
+
11
*
12
!
2
3 a d b e c f
4
5
6
S
8
Z g j m
7 t
9 h k n p u w l i o q v x r y s z
13
?
14
#
15
1
For example, to enter May 31, you could use the following sequence:
1. In Alpha Mode ( [Message] button is lit), press 6 once to enter an “M.”
2. Press 2 five times to enter an “a.”
3. Press 9 eight times to enter a “y.”
4. Press (Transfer) to enter a space.
5. Press (Message) to switch to Numeric Mode.
6. Press 3.
7. Press 1.
8. Press (Speaker), #, or lift the handset to save the entry.
Page 22
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
M
P
G
J
A
D
1
:
T
W
«
6
7
4
5
Button
1
2
3
8
9
0
M
P
G
J
A
D
1
:
T
W
¡
6
7
4
5
Button
1
2
3
8
9
0
N
Q
H
K
B
E
-
2
U
X
¿
O
R
I
L
C
F
/
3
V
Y
ª
Personalizing Your Phone
N
Q
H
K
B
E
-
2
U
X
»
6
S
4
5
8
Z
2
3
,
4
O
R
I
L
C
F
/
3
V
Y
0
The following tables show the dialpad characters for the Canadian French and Mexican Spanish languages.
M
7
G
J
Dialpad Characters — Canadian French
Number of Times Dialpad Button is Pressed
5 6 7 8 9 10 11
.
; ( ) & + *
A
D b e c f
À
È
Â
É
Æ
Ê
Ç
Ë
Î Ï î ï
T
9 n p h k u w o q l i v x
Ô r
Ù y
Œ s
Û z
ó
Ü
Ÿ
œ
ù
Ÿ
12
!
à
è
û
13
?
â
é
Ü
14
#
æ
ê
ç
ë
15
1
6
S
4
5
2
3
,
4
8
Z
º
M
7
G
J
Dialpad Characters — Mexican Spanish
Number of Times Dialpad Button is Pressed
5
.
6
; (
7
)
8 9
&
10
+
11
*
A
D b e c f
Á
É
Á
é
Í Í
T
9
0 n p h k u w o q l i v x
Ñ r
Ú y
Ó s
Ü z
ñ
ú
ó
ü
12
!
13
?
14
#
15
1
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 23
Personalizing Your Phone
Using Programmable Buttons
For quick access, you can assign feature codes, extensions, speed-dial numbers, trunks, or other resources to your programmable buttons. The new button assignments are self labeled, which means the button labels automatically appear on the Display when the buttons are programmed. You can then press the programmed buttons to activate features or place calls.
See “
Default Access Codes “ and “Default Feature Codes” on page 25 for code lists. You cannot
reprogram the default button assignments. See “Programmable Buttons” on page 6 .
To program a button:
1. With the handset on-hook, dial 397.
2. Press the button that you want to program. If the button is:
•
not programmed, UNDEFINED KEY appears.
•
programmed, the feature or extension programmed for the button appears.
•
not programmable, NON-PROGRAMMABLE KEY appears.
3. Enter the feature code, extension number, station speed-dial number, or system speeddial number to be assigned to the button. To assign speed-dial numbers to
programmable buttons, see “Assigning Speed-Dial Numbers to Programmable Buttons” on page 38
.
NOTE
Before or after assigning the speed-dial number to a programmable button, make sure the speed-dial number has either a Station Speed Dial bin or
System Speed Dial location assigned to it. For System Speed Dial numbers, numbers are pre-assigned to the System Speed Dial locations (000 to 999 or 0000 to 4999) by your system administrator. Therefore, you just need to
choose a System Speed Dial location that you want to use (see “Using
System Speed Dial” on page 36 for details). For Station Speed Dial
numbers, you must manually store numbers in the Station Speed Dial bins
(0 to 9). See “Using Station Speed Dial” on page 36 .
After you program a button, you can:
•
Press the button to place a call to the assigned extension.
•
Press the button and then hang up to transfer a call to the assigned extension. If the call is transferred to voice mail you hear repeating double tones.
•
Visually monitor the call activity of the assigned extension if the button you assign has a lamp.
The following table describes the lamp signals and the indicated call activity for a DSS/BLF key
(station speed-dials do not show status).
Lamp Signals
Continuously Lit
Slowly flashing
Quickly flashing
Continuously flashing
Description
The extension is busy or off-hook.
The extension is in Do-Not-Disturb (DND).
The extension has a call ringing in.
The extension is causing a “Station Off-Hook” system alarm.
Page 24
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Personalizing Your Phone
Default Access Codes
The following are default system access codes. If your system uses different codes, record the codes in the “New Code” column for reference.
Outside Line Access Codes
Code Type
Emergency Call
Outgoing Call (Default)
Select Line Group 1 to 208
Automatic Route Selection
Code
911 (999/112 Europe)
8
92001 to 92208
92000
New Code
Extension Numbers
Code Type
Attendant
Phone Extensions
Hunt Groups
Code
0
1000 to 1999
2000 to 2299
New Code
Default Feature Codes
The following table lists default feature codes. If your system administrator changes any of the default codes, you can record the new codes in the “New Code” column for reference.
NOTE
Most of the following feature codes work when your IP phone is idle. However, if you are on an active call or if the IP phone is off-hook, you may need to press
(Special) before you enter the feature code to activate the feature.
To delete the characters entered:
Press (Hold) to move the cursor to the left and delete the characters entered.
To cancel the feature:
Press
*
.
Feature
Account Code – Follow Calls
Account Code – Optional
ACD Agent – Log In
ACD Agent – Log In/Out
ACD Agent – Log Out
ACD Agent – Wrap-up Terminate
Activate Door Relay
Agent Help – Reject
Agent Help – Request
Page
Code
327
329
332
376
375
391
390
326
328
New Code
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 25
Personalizing Your Phone
Feature
Answer Ringing Call
Automatic IC Access – On/Off
Automatic Trunk Access – On/Off
Automatic Trunk Answer
Background Music – On/Off
Barge-In
Call Forward – All Calls
Call Forward – If Busy
Call Forward – If No Answer
Call Forward – No Answer/Busy
Call Logging
Conference
Default Station
Directory
Display Time And Date
Do-Not-Disturb
Do-Not-Disturb – Cancel
Do-Not-Disturb – On/Off
Do-Not-Disturb – Override
Dynamic Extension Express On
Dynamic Extension Express Off
Dynamic Extension Express On/Off
Dynamic Extension Express Handoff
Group Listen
Handsfree – On/Off
Headset – Off
Headset – On
Headset – On/Off
Hold – Individual
Hold – System
Hookflash (Recall in Europe)
Hunt Group – Remove
Hunt Group – Remove/Replace
Hunt Group – Replace
Display Contrast Control
Message – Cancel Left Message
Message – Delete Message
Page 26
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page
Code
336
335
330
322
319
316
315
317
324
323
303
366
368
362
364
388
312
371
372
373
363
394
307
300
370
356
358
333
5
313
386
355
357
351
361
360
350
New Code
Feature
Message – Leave Inter-station Message
Message – View Messages
Microphone Mute – On/Off
Page
Page Receive – On/Off
Program Buttons
Program Station Password
Programmable Buttons – Return to Default
Queue (Callback) Request
Record-A-Call
Redial
Redirect Call
Reminder Message
Reminder Message – Cancel
Remote Programming
Reverse Transfer (Call Pick-Up)
Ring Intercom Always – On/Off
Ring Tone Selection
Station Monitor
Station Speed Dial
Station Speed Dial – Programming
Steal Call
System Forward – Off
System Forward – On
System Forward – On/Off
System Speed Dial
Switch Keymap
Transfer To Hold
Transfer To Ring
View Programmable Button Assignments
Page
Personalizing Your Phone
New Code Code
354
381
399
346
345
396
383
387
353
352
377
398
321
382
305
306
359
4
6
385
380
331
325
397
392
395
367
365
314
7
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 27
Personalizing Your Phone
Listening to Background Music
If your system is equipped with a music source, you can listen to background music or system audio (for example, organizational conference calls) through the external speaker.
To turn on or turn off background music:
Dial 313 (on/off). BACKGROUND MUSIC ON (or OFF) appears.
Viewing Button Assignments
You can view programmable button (key) feature assignments.
To view button assignments:
1. With the handset on-hook, dial 396. PRESS THE KEY TO REVIEW appears.
2. Press any of the feature buttons to display the assignment.
3. Press (Speaker) to exit.
Resetting Programmable Buttons
You can reset all buttons (keys) that you have programmed to the default assignments.
Resetting the programmable buttons does not reset button assignments programmed by the system administrator.
To reset the feature buttons to the default values:
With the handset on-hook, dial 395. FEATURE KEYS DEFAULTED appears.
Resetting the IP Phone to the Default Settings
Resetting the IP phone to the default settings does the following:
•
Returns all volume settings to the default levels. See “Changing Volume Levels” on page 16 .
•
Cancels Background Music. See “Listening to Background Music” on page 28
.
•
Cancels Callback (queue) requests. See “Requesting a Callback (Queuing the Phone)” on page 34 .
•
Restores Handsfree Mode. “Using Handsfree Mode” on page 41 .
•
Cancels Manual Call Forwarding. See “Manual Call Forwarding” on page 45
.
•
Cancels System Forwarding. See “System Forwarding” on page 45 .
•
Cancels Do-Not-Disturb (DND). See “Using Do-Not-Disturb (DND)” on page 61 .
•
Restores Page settings. See “Paging Other System Users” on page 63 .
•
Resets hunt group calls. See “Hunt Groups” on page 65
.
To reset your IP phone to the default settings:
Dial 394. STATION DEFAULTED appears.
Page 28
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Personalizing Your Phone
Switching Keymaps
Keymaps are the default button assignments on your IP phone. Your system administrator may have programmed an alternate keymap, allowing you to switch between keymap assignments.
Contact your system administrator for more information.
To switch between keymaps when your IP phone is idle:
With the handset on-hook, dial 399. The display shows either ALTERNATE (or)
STANDARD KEYMAP IS ACTIVE.
To switch between keymaps during a call:
Press (Special), and then dial 399.
Activating Door Relay
If the Activate Door Relay feature is enabled, you can unlock a door (i.e., “buzz” it open) through your IP phone.
You can enter the Activate Door Relay feature code while idle or while on a call. This allows you to activate the feature while talking to a communications device mounted at the door without first having to hang up. When activated while on a call, the feature will not affect the call in progress other than to show a short confirmation on the display.
You can add the Activate Door Relay feature to a phone keymap button, just like any other station feature.
To unlock a door:
While idle or while on a call, dial 332. The door is unlocked.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 29
Answering and Placing Calls
Answering and Placing Calls
The following instructions describe how to answer and place internal and external calls and how to use related features.
NOTE
By default, internal (intercom) calls are assigned to the IC button, and external calls are assigned to the Call Key buttons.
Answering Calls
Your IP phone may be preset to automatically answer incoming internal calls in Handsfree
Mode. To disable Handsfree Mode, see “Using Handsfree Mode” on page 41 . After disabling
Handsfree Mode, you can use your handset or headset to answer incoming calls.
To answer a call:
Lift the handset, or press (Speaker) to answer a call while using a headset, or to
answer a call in Handsfree Mode. See “Using Handsfree Mode” on page 41
.
If you are currently on a call, press the flashing IC or Call Key button to answer a waiting call. See “
Answering Waiting Calls ” below.
Answering Waiting Calls
If you receive a call while you are on another call, you hear a “call waiting” tone, the IC or Call button flashes, and the display shows the Caller ID information (if available).
To answer a waiting call:
Press the flashing IC or Call Key button. This action hangs up on the connected call and connects you to the waiting call. You can also place the first call on hold before you
answer the waiting call. See “Placing Calls On Hold” on page 42 .
Using Automatic Call Access
Automatic Call Access connects you to incoming internal or external calls when you pick up the handset or press (Speaker). When Automatic Call Access is turned off, you must press the flashing IC or Call Key button to answer incoming calls.
To use Automatic Call Access for incoming IC calls:
With the handset on-hook, dial 361 to turn on (or off). AUTO IC ACCESS ON (or OFF) appears.
To use Automatic Call Access for incoming external (trunk) calls:
With the handset on-hook, dial 360 to turn on (or off). AUTO TRNK ACCESS ON (or
OFF) appears.
Page 31
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Answering and Placing Calls
Redirecting Calls
You can redirect calls to another extension or external number. If you have a 5340 IP Phone, you can use the menu buttons to redirect calls to the following destinations:
•
SEND TO V-MAIL: Sends the call directly to your voice mailbox. You must have a mailbox to use this destination.
•
IC CALL TO DND: Places your IP phone in DND Mode and blocks the call. See “Using
Do-Not-Disturb (DND)” on page 61
.
•
SEND TO DEST: Redirects the call to the extension or phone number entered.
To redirect calls:
1. While a call is ringing, dial 331 or press the menu button as described above (5340 IP
Phones only).
2. Do one of the following:
•
Dial the extension number, or press the Outgoing button or the Outgoing Call access code (the default code is 8), and then dial the external number.
•
Enter the DND code.
Using Automatic Trunk Answer
You can use Automatic Trunk Answer to answer incoming external calls for other internal parties who are members of an “Answer Access” list. Your system administrator creates Answer
Access lists. Contact your system administrator for Answer Access list extensions.
1
Automatic Trunk Answer answers calls in the order they are received (that is, the first call received by any extension in the Answer Access list is the first one answered).
To use Automatic Trunk Answer:
1. While an incoming external call is ringing at another Answer Access list extension, lift the handset or press (Speaker).
2. Dial 350 or press the flashing Trunk <number> button.
Page 32
1.
This feature may or may not be enabled for your system.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Answering and Placing Calls
Placing Calls
The following instructions describe how to place calls and related features.
Placing Emergency Calls
WARNING
Contact your system administrator and your local Mitel provider for important information about dialing emergency services before using your IP phone.
When dialing an emergency number (911 U.S. or 999/112 Europe), you do not have to press the Outgoing button or enter the Outgoing Call access code (8 is the default code). The system automatically places emergency calls immediately after you dial the number, even if you do not select an outside line.
Placing Emergency Calls using the LIM Line
Emergency Number dialing should only be performed by picking up the handset and selecting the Analog Line key you have programmed. If Privacy Mode is enabled and the Analog Line key local line is busy, dialing will not occur on the LIM line. Emergency dialing using an IP connection may not be supported due to system configuration and country location. For more
information, contact your System Administrator. For details about LIM, see “Using the Line
Interface Module (LIM)” on page 11 .
To make an Emergency Call using the Line Interface Module line:
1. Lift the handset.
2. Press the Analog Line key that you have programmed. ANALOG CALL appears.
3. Dial your local emergency number.
To make an Emergency Call using the Line Interface Module line, when the IP connection has failed:
1. Lift the handset.
2. Press the Analog Line key that you have programmed. IP FAIL: ANALOG CALL appears.
3. Dial your local emergency number.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 33
Answering and Placing Calls
Placing Internal Calls
Internal calls are calls placed to other extensions in the system. Internal calls are assigned to the Intercom (IC) button on your IP phone. Contact your system administrator for a list of extension numbers.
To place an internal call:
With or without the handset lifted, dial the extension number. If you enter incorrect digits, you can press (Hold) to move the cursor backward, deleting the last digits entered.
If you are using Handsfree Mode, speak after you hear a double tone.
If there is no answer or if the extension is busy, you can do the following:
•
Request a callback (queue). See “
Requesting a Callback (Queuing the Phone) ” below.
•
Camp-on to the busy extension. See “ Using Camp-on ” below.
•
Leave a message. See “Leaving Messages at Other Extensions” on page 59
.
Requesting a Callback (Queuing the Phone)
When you request a callback (queue the phone), the system calls you when the extension is available and places a call to the IP phone.
To request a callback:
If there is no answer or if the extension is busy, press (Special) followed by 6 or the
QUEUE menu button (5340 IP Phones only), and then hang up. QUEUE REGISTERED
FOR <name> appears. When the extension becomes available, your extension rings.
To cancel the callback request:
Press 6 or the CANCEL QUEUE menu button (5340 IP Phones only). QUEUE
REQUEST CANCELED appears.
Using Camp-on
Camp-on keeps you connected to the called extension until it becomes available. You cannot use Camp-on if the called extension is in DND, or if the call is forwarded to voice mail. See
“Using Do-Not-Disturb (DND)” on page 61 .
To use Camp-on:
Stay on the line and wait for the extension to become available. Do not hang up. If Campon is enabled, you hear Music-on-Hold while you are waiting.
Page 34
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Answering and Placing Calls
Placing External Calls
The following sections describe features used when placing external calls.
To place an external call:
1. Press the Outgoing button, an unlit Call Key button, or enter the Outgoing Call access code (8 is the default code).
2. Dial the number.
NOTES
If you cannot place an external call because all outgoing lines are busy, you can request a callback, which prompts the system to contact you when a
line becomes available. See “Requesting a Callback (Queuing the Phone)” on page 34 .“
If you are prompted for an account code (indicated by a single beep), you
must enter an account code before you can place your call. See “Using
.
Depending on system configuration, you may also be able to use one of the following methods to select an outgoing line:
•
Enter the Select Line Group feature code. The default codes are 92001 to 92208.
•
Enter the Automatic Route Selection (ARS) feature code. The default code is 92000.
Contact your system administrator for more information about using Select Line Group or ARS access codes.
Redialing a Number
You can quickly redial the last external number dialed. You cannot redial extension numbers.
To use Redial:
With or without the handset lifted, press a line and dials the number.
(Redial). The system automatically selects
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 35
Answering and Placing Calls
Using Speed Dial
You can use speed dial to quickly dial stored phone numbers. Speed-dial numbers are either stored in the system (System Speed Dial), or in your IP phone (Station Speed Dial).
Using System Speed Dial
Your system administrator assigns System Speed Dial location numbers, which are available to anyone in the system. Contact your system administrator for more information.
To view or dial System Speed-Dial numbers:
1. Dial 381. REVIEW SYS SPEED # <code range> appears.
2. Do one of the following:
•
Press (Up) or (Down) to scroll through the speed-dial locations.
•
Enter the speed-dial location (000 to 999 or 0000 to 4999).
3. Press # or the ACCEPT menu button (5340 IP Phones only) to dial the number.
Using Station Speed Dial
You can use Station Speed Dial to store phone numbers for your personal use. Other system users do not have access to your Station Speed-Dial numbers.
Storing Station Speed-Dial Numbers
You can store up to 10 Station Speed-Dial numbers.
To store a Station Speed-Dial number:
1. With the handset on-hook, dial 383. PROGRAM STN SPD (0-9) OR SCROLL appears.
2. Do one of the following:
•
Press (Up) or (Down) to scroll through the speed-dial bins.
•
Enter the speed-dial bin (0 to 9).
Press # or the ACCEPT menu button (5340 IP Phones only) to select the bin.
3. Enter the name of the speed-dial contact (up to 10 characters). For dialpad character
descriptions, see “Using the Dialpad Buttons to Enter Characters” on page 22 .
4. Press # or the ACCEPT menu button (5340 IP Phones only) to save the name.
5. Enter the extension number or external number. If you are storing an external number, enter the Outgoing Call access code (default code is 8) before you enter the number. Do not use hyphens or colons in stored speed-dial numbers.
6. Press # or the ACCEPT menu button (5340 IP Phones only) to save the bin. STN SPD
BIN # <number> UPDATED appears.
Page 36
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Answering and Placing Calls
Dialing Station Speed-Dial Numbers
To dial a Station Speed-Dial number:
Do one of the following:
•
Dial 382, and then enter the Station Speed Dial bin (0 to 9). The system dials the number.
•
Press (Up) or (Down) to scroll through the speed-dial bins, and then press
# to select the bin and dial the number.
NOTE
You can also program buttons to dial Station Speed-Dial numbers.
See “Assigning Speed-Dial Numbers to Programmable Buttons” on page 38
.
Deleting Station Speed-Dial Entries
To delete a Station Speed-Dial entry:
1. With the handset on-hook, dial 383. PROGRAM STN SPD (0-9) OR SCROLL appears.
2. Do one of the following:
•
Press (Up) or (Down) to scroll through the speed-dial bins.
•
Enter the speed-dial bin (0 to 9).
3. Press # or the ACCEPT menu button (5340 IP Phones only) to select the bin.
4. Press (Hold) repeatedly until the name is erased, and then press # or the
ACCEPT menu button (5340 IP Phones only) to continue.
5. Press (Hold) repeatedly until the number is erased, and then press # or the
ACCEPT menu button (5340 IP Phones only). STN SPD BIN # <number> UPDATED appears.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 37
Answering and Placing Calls
Assigning Speed-Dial Numbers to Programmable Buttons
You can assign Station or System Speed-Dial numbers to your programmable buttons.
NOTE
Before or after assigning the speed-dial number to a programmable button, make sure the speed-dial number has either a Station Speed Dial bin or System Speed
Dial location assigned to it. For System Speed Dial numbers, numbers are preassigned to the System Speed Dial locations (000 to 999 or 0000 to 4999) by your system administrator. Therefore, you just need to choose a System Speed Dial
location that you want to use (see “Using System Speed Dial” on page 36 for
details). For Station Speed Dial numbers, you must manually store numbers in the
Station Speed Dial bins (0 to 9). See “Storing Station Speed-Dial Numbers” on page 36 .
To program a Station Speed-Dial button:
1. With the handset on-hook, dial 397. PRESS THE BUTTON TO PROGRAM appears.
2. Press the feature button that you want to program as a speed-dial button.
3. Dial 382.
4. Do one of the following:
•
Press (Up) or (Down) to scroll through the speed-dial bin.
•
Enter the speed-dial bin (0 to 9), or select the menu button designation from the display (5340 IP Phones only).
To program a System Speed-Dial button:
1. With the handset on-hook, dial 397. PRESS THE BUTTON TO PROGRAM appears.
2. Press the feature button that you want to program as a speed-dial button.
3. Dial 381.
4. Do one of the following:
•
Press (Up) or (Down) to scroll through the speed-dial location.
•
Enter the speed-dial location (000 to 999 or 0000 to 4999), or select the menu button designation from the display (5340 IP Phones only).
Page 38
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Answering and Placing Calls
Using the Directory
You can use the Directory to find internal or external contacts or find and activate system features. The directory uses Intelligent Directory Search (IDS), which is similar to the “text on 9 keys” (T9) predictive search feature used for mobile phones. The Directory has the following three subdirectories:
•
Intercom: Find and dial internal numbers.
•
Outside: Find and dial external numbers listed in the company directory.
•
Feature: Find and activate system features.
When searching the directory, dialpad buttons can represent several characters, as shown in the following table. As you enter characters, the entries that best match the characters entered appear. The system connects the character sequence to possible directory matches. For example, to find the name “Jones,” dial 56637.
Button Characters Represented
6
7
4
5
2
3
0
1
0
1
2 A B C a b c Ç â ä à å ç Ä Å á
3 D E F d e f é ê ë è É
4 G H I g h i ï î ì í
5 J K L j k l
6 M N O m n o ô ö ò Ö ó ñ Ñ
7 Q P R S q p r s
8
9
8 T U V t u v ü û ù Ü ú
9 W X Y Z w x y z ÿ
(Up) Scroll to next entry
(Down) Scroll to previous entry
*
#
Cancel search
Activate selection
(Hold) Move the cursor to the left, deleting existing characters
See page 40 for detailed instructions on using the directory.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 39
Answering and Placing Calls
To search for a directory name or feature:
1. Dial 307, and then press one of the following:
•
1 for the IC directory.
•
2 for the Outside directory.
•
3 for the Feature directory.
•
The Directory menu button (IC, OUTSIDE, or FEATURE—5340 IP Phones only).
2. Press the dialpad buttons to enter (up to 20) characters. See the table on
for dialpad button character descriptions.
3. Press (Up) or (Down) or the >> (Next) or << (Previous) menu buttons (5340 IP
Phones only) to scroll through the entries.
NOTE
The IC directory may display two similar entries, one without an asterisk and one with an asterisk. The entry without an asterisk is the primary extension. The entry with an asterisk is a secondary extension.
4. Press # (or the menu button next to the entry [5340 IP Phones only]) while the display shows the entry to dial a number or activate a feature code.
Using Account Codes
Account codes record information for phone record reports. You may be required to enter account codes when placing calls. Contact your system administrator for more information about using account codes.
There are three types of account codes:
•
Standard account codes: Automatically entered into the phone record report whenever you place a call.
•
Forced account codes: Entered before you can place an outside call.
•
Optional account codes: Entered at any time during a call.
To enter an optional account code:
1. While off-hook, press (Special), and then dial 390.
2. Enter the optional account code, and then press #.
To set an account code for all calls placed from your IP phone:
Dial 391 followed by the account code, and then press #. ACCOUNT CODE ACCEPTED appears. This code is used for all calls made from your IP phone until it is disabled.
To disable the code:
Dial 391, and then press #. ACCOUNT CODE CLEARED appears.
Page 40
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
Call Features
The following sections describe call-related features.
Using Handsfree Mode
You can use Handsfree Mode to activate the speakerphone.
NOTES
The Ring Intercom Always feature prevents calls from being answered in
Handsfree Mode (see the following section).
You cannot use Handsfree Mode if you are using a headset, or if you have more than one phone assigned to an extension number.
To use Handsfree Mode:
With the handset on-hook, dial 319. HANDSFREE MODE ON appears. Dial 319 again to turn Handsfree Mode off.
Using Ring Intercom Always
If another extension has Handsfree Mode enabled for incoming internal calls (see the previous section), you can use Ring Intercom Always to override Handsfree Mode on the extension, requiring the called party to pick up the handset to answer your call.
To override Handsfree Mode for the current call:
1. Before you enter the extension number, press #. RING EXTENSION NUMBER appears.
2. Dial the extension number.
To use Ring Intercom Always to always send non-handsfree calls:
With the handset on-hook, dial 377. RING IC ALWAYS ON appears. Dial 377 again to turn Ring Intercom Always off.
Using Mute
You can use Mute to temporarily turn off your microphone, preventing the other party on the call from hearing you.
To mute or unmute the microphone:
While on a call, press (Mute). MICROPHONE MUTE ON appears. When the microphone is muted, the Mute button lamp is lit. Press (Mute) again to unmute the microphone.
Page 41
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
Placing Calls On Hold
You can place calls on either Individual Hold or System Hold.
•
Individual Hold: Places an internal or external call on hold at your IP phone.
•
System Hold: Places an external call on hold in the system. You can then pick up the call from any phone that indicates a flashing Call button for the call, including the IP phone that placed it on hold.
To place a call on Individual Hold:
1. Press (Hold). ENTER EXTENSION NUMBER appears.
2. Hang up or place another call.
To place an outside call on System Hold:
1. Press (Special), and then dial 335. ENTER EXTENSION NUMBER appears.
2. Hang up or place another call.
To place a call on hold and answer a waiting call:
Press (Hold), and then press the flashing IC or Call Key button.
To return to a call that is on hold:
Press (Hold), and then lift the handset or press (Speaker). <Caller> WAS
HOLDING appears.
Entering a Hookflash
Some telephone companies require you to enter a hookflash (a quick hang up and release) for feature access.
To enter a hookflash:
While off-hook, press (Special), and then dial 330 or press the FLASH menu button
(5340 IP Phones only).
Page 42
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
Transferring Calls
You can transfer calls to other extensions or external numbers. You can also transfer
conference calls. See “Transferring a Conference” on page 48
for more information.
Transferring Calls to Other Extensions
To transfer a call to another extension:
1. While on the call, press (Transfer), and then enter the extension number.
2. Do one of the following:
•
Wait for an answer, announce the call, and then hang up. If the extension is unavailable, press the flashing IC or Call Key button to return to the caller.
•
Hang up to transfer the call and disconnect the call from your IP phone.
NOTE
If your system administrator has enabled the Transfer-on-Connect
Allowed feature for your IP phone, you are automatically connected to calls transferred to your extension after the transferring party hangs up.
If this option is turned off, you must press an IC or Call Key button to answer calls transferred to your extension.
Transferring Calls to External Numbers
To transfer a call to an external number:
1. While on the call, press (Transfer).
2. Press the Outgoing button or the Outgoing Call access code (the default code is 8) to select an outside line.
3. Dial the phone number.
4. Do one of the following:
•
Wait for an answer, announce the call, and then hang up. If the extension is unavailable, press the flashing Call Key button to return to the caller.
•
Hang up to transfer the call and disconnect the call from your IP phone.
Using Reverse Transfer
You can use Reverse Transfer (Call Pick Up) to answer calls that are ringing or holding at other extensions. For example, if you receive a call while you are away from your desk, you can pick up the call from another extension.
To use Reverse Transfer:
1. Lift the handset, and then press 4. ENTER EXTENSION NUMBER appears.
2. Dial the extension or hunt group number or press a DSS/BLF key where the call is ringing or holding. The call is transferred to the IP phone you are using and you are connected to the caller.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 43
Call Features
Viewing Your System Information
If you are on a call, you can temporarily view your user information (your user name and your extension number) and the date and time.
To display your user information and the date and time:
Press (Special), and then dial 300.
Viewing Caller ID Information
If you are currently connected to an external caller with Caller ID, you can toggle between the caller’s name and number. If the name is unavailable, CANNOT ACCESS FEATURE appears.
To show the outside party’s name/number:
Press (Special), and then dial 379.
Page 44
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
Forwarding Calls
You can use Manual Call Forwarding or System Forwarding to forward calls.
Manual Call Forwarding
The following table describes Manual Call Forwarding options.
Call Forward Feature
Call Forward All Calls
Call Forward If No
Answer
Call Forward If Busy
Call Forward If No
Answer/Busy
Description
All incoming calls are forwarded.
All incoming calls are forwarded if not answered. (The timer is set by the system administrator.)
When your IP phone is busy, all incoming calls are forwarded without ringing.
All incoming calls are forwarded if your IP phone is busy, or if you do not answer.
Code/Menu Button
(5340 IP Phones only)
355
ALL
356
NO ANSWER
357
BUSY
358
NO ANSWER/BUSY
To use Manual Call Forwarding:
1. Press the Fwd All button (5320/5330 IP Phone) or Forward button followed by the menu button designation (5340 IP Phone), or dial the Manual Call Forwarding feature code from the previous table. ENTER FORWARD DEST appears.
2. Enter the extension number, or press the Outgoing button or the Outside menu button
(5340 IP Phones only), and then dial the telephone number. On the 5340 IP Phone, you can press the VOICE MAIL menu button to forward calls to the Message Center (voice mailbox). FWD ALL CALLS TO <number> appears.
To cancel a Manual Call Forwarding request:
•
5320/5330 IP Phone: Press the Fwd All button, and then press # (Speaker), or lift the handset.
•
5340 IP Phone: Press Forward button, and then press the FWD OFF menu button.
NOTE
If the Configuration Assistant feature is enabled for your system, you can access a voice guided configuration portal that provides easy-to-use, remote access to the
Call Forwarding feature. See page 53 for details.
System Forwarding
You can use System Forwarding to route calls based on the type of call and the idle or busy status of your IP phone. You cannot program the System Forward destination. You can only turn it on or off. Contact your system administrator for more information.
To turn System Forwarding on or off:
Dial 354. SYSTEM FORWARD ON appears. Dial 354 again to turn System Forwarding off.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 45
Call Features
Using Dynamic Extension Express
When you enable Dynamic Extension Express on your IP phone, your incoming calls are automatically routed to one or more preprogrammed associated destinations according to the routing steps programmed for you.
Typically, your desk phone is configured to be your main extension. You may be programmed for up to five associated destinations including:
• softphone
• home IP phone
• voice mail
• mobile phone
• home phone
Your desk phone, softphone, home IP phone and voice mail extensions are already programmed in the system, so your system administrator can easily include them in your routing steps. To include your mobile and home phone numbers in your routing steps, you will need to provide these numbers to your system administrator.
Dynamic Extension Express also includes the Handoff feature, which includes the following functions:
•
Push: The Handoff “push” function allows you to move an active call from your main extension, typically your desk phone, to an associated destination without disconnecting audio. The push function is useful if you are leaving the work area, but want to remain connected to an active call. The push function rings all associated destinations (except voice mail) and you select which device to use to answer the call. When you answer the call, you are immediately connected to the other parties at the new destination. When the call is switching over to the new destination, there may be a momentary break in audio, which may be noticeable to the other parties on the call.
•
Pull: The Handoff “pull” function allows you to pull a call that was previously routed to your mobile or home phone back to the main extension. The pull function is useful if you answer a call on your mobile phone and then return to your desk. After you pull a call back to the main extension, the call is connected immediately and you can then access system features such as conference, hold, and transfer.
NOTE
The Handoff feature is only supported on your main extension, typically your desk phone. However, if you share a desk phone with one or more coworkers and your main extension is a phantom extension, you cannot use the Handoff feature.
Dynamic Extension Express includes the following feature codes:
•
Dynamic Extension Express On: 363
•
Dynamic Extension Express Off: 362
•
Dynamic Extension Express On/Off: 364
•
Dynamic Extension Express – Handoff (push and pull): 388
The following call types do not follow Dynamic Extension Express:
•
Hunt group calls
•
Hunt group announcement/overflow calls
•
Transfer recalls, Hold recalls, Conference recalls, and Attendant recalls
NOTE
A recall occurs when a feature cannot be completed or the feature times out, and the call returns to the originating extension. For example, a holding call will recall the extension where it was placed on hold when the hold timer expires.
Page 46
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
When you enable Dynamic Extension Express, your incoming calls are routed as specified by the routing type programmed for you by your system administrator. The table below provides descriptions for the default routing types.
Routing Type
Mobile Twinning
Delayed Mobile
Twinning
Description
Calls simultaneously ring your desk phone and mobile phone, before going to voice mail.
Calls ring your desk phone first, and then ring both your desk phone and mobile phone, before going to voice mail.
Check with your system administrator to see which routing type has been programmed for you.
Your administrator can modify these routing types by adding or removing routing steps, adding or removing destinations, and changing the ring timers, if required.
To ensure that calls are routed correctly to your mobile and home phones, inform your system administrator if either of these phone numbers change.
To enable Dynamic Extension Express:
Dial 363 or 364. PERSONAL ROUTING ON appears on the display.
To disable Dynamic Extension Express:
Dial 362 or 364. PERSONAL ROUTING OFF appears on the display.
To answer a call routed to your mobile or home phone:
1. Answer the call when it rings your IP phone. After you speak, the Dynamic Extension
Express prompt is played.
2. Do one of the following:
•
Press # to accept the call.
NOTE
You do not need to wait for the prompt to accept the call. You can accept the call immediately by pressing the # button.
•
Press * to send the call to the voice mailbox associated with your main extension
(not your mobile phone or home phone voice mailbox). If you do not have a voice mailbox, the “Press *...” prompt is not played and the call is routed to your main extension.
If you hang up, the call continues to follow your programmed routing steps.
To use the Dynamic Extension Express – Handoff “push” feature:
1. While on an active call at your IP phone, press (Special), and then dial 388.
HANDOFF IN PROGRESS appears on the display and the call rings all of your associated destinations (except voice mail).
2. Press # to accept and answer the call at your mobile or home phone.
To use the Dynamic Extension Express – Handoff “pull” feature:
While on an active call on an associated destination device, dial 388. A confirmation tone is played and the call is pulled back to your IP phone.
NOTE
If you enter the handoff feature code (388) and the display shows NO CALL TO
HANDOFF, the call cannot be handed off (see
).
To cancel the Dynamic Extension Express – Handoff feature:
While the handoff is in-progress, press (Special), and then dial 388. HANDOFF
CANCELLED appears on the display for your main extension.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 47
Call Features
Placing Conference Calls
You can place a conference call with up to three internal or external parties (for a total of four parties, including yourself).
To place a conference call:
1. While on the first call, press the Conference button to place the call on hold. CALL
NEXT PARTY TO CNF appears.
2. Place a call to the next conference party (for external calls, press the Outgoing button or the Outgoing Call access code [8 is the default code], and then dial the number).
3. After the party answers, announce the conference, and then press the Conference button to place the call on hold. If necessary, repeat this step to add the remaining conference party.
4. Press the Conference button again or the CONNECT TO CNF menu button (5340 IP
Phones only) to start the conference. CNF IN PROGRESS appears.
Adding a Conference Party
You can add a conference party during the conference.
To add a conference party:
1. Press the Conference button or the ADD PARTY menu button (5340 IP Phones only).
This leaves the conference parties connected.
2. Place a call to the party to be added to the conference, and then announce the conference. Press the Conference button (twice) or the CONNECT TO CNF menu button (5340 IP Phones only) to add the party and rejoin the conference.
Transferring a Conference
You can transfer an existing conference to another extension.
To transfer a conference:
1. During the conference, press (Transfer), and then dial the extension number.
2. Announce the conference (if desired), and then hang up. CONFERENCE TFR from
<name> appears on the called party’s display. The party must then press the flashing
Conference button to connect to the conference.
Dropping Out of a Conference
You can drop out of a conference and return to the conference later.
To drop out of a conference:
Press the Conference button or (Hold), and then hang up. ENTER EXTENSION
NUMBER appears. This removes you from the conference but leaves the other parties connected.
To return to the conference:
Press the flashing Call Key button. CONFERENCE WAS HOLDING appears, and you are reconnected to the conference.
Page 48
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
Ending a Conference and Placing all Parties on Hold
You can end a conference and place all conference parties on Individual Hold, allowing you to toggle between the held parties and speak to one party at a time.
To end a conference and place all parties on Individual Hold:
Press the Conference button, and then press
ON HOLD appears.
(Hold). CONFERENCE PARTIES
To toggle between the held callers:
Press parties.
(Hold) twice for internal parties or the applicable Call Key button for external
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 49
Call Features
Using Record-A-Call
You can use Record-A-Call to record an ongoing call as a mailbox message.
1
You can then retrieve the message from your voice mailbox. The Record-A-Call feature stays active after the other party hangs up, so you can add to the recorded call with your own message.
NOTE
Record-A-Call is not supported on peer-to-peer (P2P) calls. Contact your system administrator for more information.
To use Record-A-Call:
1. While on a call, press (Special), and then dial 385, or press the RECORD-A-CALL menu button (5340 IP Phones only). REQUESTING RECORD-A-CALL appears.
2. Enter the voice mailbox number where you want the recording to be saved.
RECORD-A-CALL IN PROGRESS appears, and both you and the calling party hear a confirmation tone (if enabled).
NOTE
If your system administrator assigns the Record-a-Call voice mailbox destination, you do not need to enter the voice mailbox number.
To stop Record-A-Call:
Do one of the following:
•
Press (Special), and then dial 385.
•
Press the CANCEL RECORDING menu button (5340 IP Phones only).
•
Hang up.
Using Group Listen
You can use Group Listen to activate the speaker while you use the handset or headset to continue speaking. This allows other people to hear the other party on the call while the other party can only hear you (through the handset microphone). You cannot use Group Listen in
Handsfree Mode.
To use Group Listen:
While on a call, press (Special), and then dial 312. GROUP LISTEN ON appears, and you hear a confirmation tone. The other party does not hear the confirmation tone. Dial
312 again to turn Group Listen off.
Page 50
1.
This feature may or may not be enabled for your system.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
Using Call Logging
Your call logs are records of your most recent missed, received, and dialed calls. A maximum of
20 entries are stored in each call log.
2
You can use Call Logging to:
•
View recent call activity.
•
View caller ID information.
•
Return or redial calls.
To use Call Logging:
1. Dial 333 or the LOGS menu button (5340 IP Phones only).
2. Select one of the following options:
•
Press 1 (MISS) or the MISSED CALLS menu button (5340 IP Phones only) for missed calls.
•
Press 2 (RCV) or the RECEIVED CALLS menu button (5340 IP Phones only) for received calls.
•
Press 3 (DL) or the DIALED CALLS menu button (5340 IP Phones only) for dialed calls.
•
Press 4 (CLR) or the CLEAR LOGS menu button (5340 IP Phones only) to clear all entries.
3. Press (Up) or (Down) or the >> (Next) or << (Previous) menu buttons (5340 IP
Phones only) to scroll through the entries.
The display shows the party’s name and the extension or outside number (if available) and the date and time.
If no Caller ID information is available, UNKNOWN CALLER appears.
To return a call or redial a number listed in a call log:
Press # or the CALL NOW menu button (5340 IP Phones only) while the display shows the number.
To delete individual call log entries:
Press 0 or the DELETE menu button to delete the displayed entry, or press the DEL ALL menu button (5340 IP Phones only) to delete all entries in the current call log.
2.
This feature may or may not be enabled for your system.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 51
Call Features
Using Secondary Extension Buttons
Secondary Extension buttons must be programmed by your system administrator. You can use programmable buttons as “secondary extensions.” Secondary Extensions are assigned to other extensions in the system (primary extensions). Because Secondary Extension buttons are programmed by the system administrator, you cannot change the buttons (for example, assign features to the buttons).
When programmed, you can use Secondary Extension buttons to:
•
Place an internal call to the primary extension.
•
View the call activity at the primary extension.
•
Transfer calls to the primary extension.
•
Answer a call that is ringing or holding on any Call Key button at the primary extension.
NOTES
The system administrator must set up the Call Key buttons for internal calls or you cannot use Secondary Extensions at the primary extension.
You can use Secondary Extension buttons to notify you when a given number of calls are waiting at the primary extension.
If a Secondary Extension button is flashing (the primary extension has an incoming call), you can press # before pressing the flashing Secondary
Extension button to call the primary extension and not answer the incoming call.
Page 52
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
Using Configuration Assistant
If Configuration Assistant is enabled for your system, you can access this voice guided configuration portal that provides easy-to-use, remote access to the following phone configuration options:
•
Dynamic Extension Express (see below)
•
DND (see
)
•
Manual Call Forwarding (see page 55 )
NOTE
You need a Configuration Assistant extension number to use this feature. Contact your system administrator for more information.
Changing Your Station Password
Before using Configuration Assistant, Mitel recommends that you change your default Station password to something more secure.
To change your Station password:
1. Dial 392. ENTER PASSWORD appears.
2. Enter your current password (the default password is your extension number), followed by #. CHANGE PASSWORD TO appears.
3. Enter the new password followed by #. VERIFY PASSWORD appears.
4. Enter the new password again followed by #. DATABASE UPDATED appears.
To change the password from another phone, see “Changing Your Station Password” on page 58
.
Accessing Configuration Assistant
Follow the instructions below to access Configuration Assistant.
To access Configuration Assistant:
1. Access the Configuration Assistant extension number from inside or outside the system by:
• dialing it from any phone in the system.
• being transferred to it.
• dialing it from automated attendant, voice mail, or DISA.
2. Do one of the following:
•
If calling from your main desktop phone, proceed to step 3..
•
If calling from someone else’s main desktop phone that is designated as a
Configuration Assistant user, press the Star button (*), and then enter your extension number.
•
If calling from a phone that is not designated as a Configuration Assistant user, enter your extension number.
•
If transferred to Configuration Assistant or if calling Configuration Assistant from outside the system, enter your extension number.
3. Enter your Station password, and then press #.
You may now change the settings for any of the following features:
•
Dynamic Extension Express (see
)
•
DND (see
)
•
Manual Call Forwarding (see page 55 )
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 53
Call Features
Changing the Dynamic Extension Express Settings
NOTE
This feature is available only if the authenticated extension is identified as a
Dynamic Extension Express (DEE) user. See “Using Dynamic Extension Express” on page 46
for more information.
To change the DDE settings using Configuration Assistant:
.
2. Follow the voice prompts to change your DEE status (on or off) or program a mobile phone number. When this option is selected, Configuration Assistant first states whether
DEE is currently enabled or not (for example, “Dynamic extension is enabled”), and then offers the following DEE functions:
•
Enable (only if DEE is disabled)
•
Disable (only if DEE is enabled)
•
Program mobile phone number [you do not have to enter the Outgoing feature code (8)]
3. Hang up, or press the Star button (*) to return to the main menu.
Changing the DND Settings
See “Using Do-Not-Disturb (DND)” on page 61
for more information about using DND.
To change the DND settings using Configuration Assistant:
.
2. Follow the voice prompts to change your DND status (on or off). There is no option to provide a specific DND status message. When this option is selected, Configuration
Assistant first states whether DND is currently enabled or not (for example, “Do-Not-
Disturb is currently disabled”), and then offers the following DND functions: o Enable (only if DND is disabled) o Disable (only if DND is enabled)
3. Hang up, or press the Star button (*) to return to the main menu.
Page 54
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
Changing the Manual Call Forwarding Settings
See “Manual Call Forwarding” on page 45 for more information about Manual Call Forwarding.
To change the Manual Call Forwarding settings using Configuration Assistant:
.
2. Follow the voice prompts to change your manual call forwarding status (on or off). There is no option to provide a specific call forwarding condition, such as no answer or busy.
When this option is selected, Configuration Assistant first states whether call forwarding is currently enabled or not (for example, “Call Forwarding is enabled”) and then offers the following forwarding functions:
•
Forward calls to voice mail
•
Forward calls to an internal extension number
•
Forward calls to an external phone number [you do not have to enter the Outgoing feature code (8)]
•
Disable (only if Call Forwarding is enabled)
3. Hang up, or press the Star button (*) to return to the main menu.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 55
Call Features
Using Remote Programming
If the Configuration Assistant feature is enabled for your system, Mitel recommends that you use Configuration Assistant instead of the Remote Programming feature described in this section. Configuration Assistant offers an enhanced, voice guided configuration portal that provides easy-to-use, remote access to the Call Forwarding, Dynamic Extension Express, and
DND features. See
for using Configuration Assistant.
To use Remote Programming to access these features from another system phone or an external phone, follow the instructions in this section.
3
NOTE
A Direct Inward System Access (DISA) number is required to use Remote
Programming from an external phone. Contact your system administrator for more information.
Changing the Dynamic Extension Express Settings
See “Using Dynamic Extension Express” on page 46
for more information about Dynamic
Extension Express.
To enable Dynamic Extension Express using Remote Programming:
1. Do one of the following:
•
Call your DISA number (provided by the system administrator). If necessary, enter your DISA password.
•
Use any phone on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your Station password followed by #. See
for details on setting up a
Station password for your extension.
5. Dial 363 (Dynamic Extension Express On).
To disable Dynamic Extension Express using Remote Programming:
Follow steps 1 - 4 above, dial 362 (Dynamic Extension Express Off), and then hang up.
Page 56
3.
This feature may or may not be enabled for your system.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Call Features
Changing the DND Settings
See “Using Do-Not-Disturb (DND)” on page 61
for more information about using DND.
To turn on DND using Remote Programming:
1. Do one of the following:
•
Call your DISA number (provided by your system administrator). If necessary, enter your (DISA) password.
•
Use any phone on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your Station password followed by #. See
for details on setting up a
Station password for your extension.
5. Dial 370.
6. Enter the DND message number (01 to 20), and then enter the second-line message text (if applicable).
To turn off DND using Remote Programming:
Follow steps 1 through 4 above, and then dial 371.
Changing the Manual Call Forwarding Settings
See “Manual Call Forwarding” on page 45 for more information about Manual Call Forwarding.
To turn on Manual Call Forwarding using Remote Programming:
1. Do one of the following:
•
Call your DISA number (provided by your system administrator). If necessary, enter your DISA password.
•
Use any phone on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your Station password followed by #. See
for details on setting up a
Station password for your extension.
5. Dial one of the following Call Forwarding feature codes:
•
355 (All)
•
356 (No answer)
•
357 (Busy)
•
358 (No Answer/Busy)
6. Enter either an extension number or 8 followed by a phone number.
To turn off Call Forwarding using Remote Programming:
Dial 355, and then hang up.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 57
Call Features
Changing Your Station Password
You can use Remote Programming to change the Station password. See
for details on setting up a Station password for your extension.
To change your Station password using Remote Programming:
1. Do one of the following:
•
Call your DISA number (provided by your system administrator). If necessary, enter your DISA password.
•
Use any phone on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your password followed by #.
5. Dial 392.
6. Enter the new password followed by #.
7. Enter the new password again followed by #.
Page 58
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Messages
Messages
This section describes the following system messaging features:
•
Inter-station messages: Inter-station messages are alerts sent to your IP phone by other internal parties, notifying you to contact the party who left the message. The
(Message) button and Message/Ring Indicator flash to notify you of the new message. You can then either delete the message or reply to the message, which automatically places a call to the party who left the message.
•
Do-Not-Disturb (DND) messages: Messages that other internal parties see when your IP
phone is in DND. See “Using Do-Not-Disturb (DND)” on page 61
.
•
Reminder messages: Messages that you can use to notify yourself of upcoming
appointments, meetings, and so on. See “Using Reminder Messages” on page 62 .
•
Pages: Announcements sent over phone speakers or external speakers. See “Paging
Other System Users” on page 63 .
•
Voice messages: System voice mail messages.
NOTE
Because a variety of voice mail products work with the 5000 CP, this guide does not include voice mail instructions. For voice mail instructions, refer to the voice mail user guide for your system. For example, refer to the
Enterprise Messaging, Basic Voice Mail, and Embedded Voice Mail Card
User Guide, part number 835.3205, or the Mitel NuPoint Unified Messaging
User Guide on the Mitel Web site (http://edocs.mitel.com). Contact your system administrator for more information about your voice mail system.
Leaving Messages at Other Extensions
You can leave inter-station or voice mail messages for other internal parties.
To leave an inter-station or voice message for a busy IC extension:
1. Press (Message) or the LEAVE MESSAGE menu button (5340 IP Phones only).
HANG UP OR WAIT FOR MSG CENTER appears.
2. Do one of the following:
•
Hang up to leave an inter-station message. MESSAGE LEFT FOR <name> appears.
•
Stay on the line to connect to the message center (usually voice mail).
To leave an inter-station message without placing an internal call:
1. Dial 367 (Leave Message), or press (Message), and then press the LEAVE
MESSAGE menu button (5340 IP Phones only). LEAVE MESSAGE ON EXTENSION appears.
2. Enter the extension number. MESSAGE LEFT FOR <name> appears.
Page 59
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Messages
Viewing and Responding to Messages
When you have waiting messages, the (Message) button and Message/Ring Indicator flash and the display shows the number of waiting messages.
NOTE
If your handset or speakerphone is off-hook when you view an inter-station message, you automatically call the party who left the message.
The display shows new messages as follows:
•
Inter-station messages sent by other internal parties are indicated by the party’s programmed user name.
•
Voice messages are indicated by FROM MBOX <your extension number>.
To view or respond to messages:
1. With the handset on-hook, press (Message) or the VIEW MESSAGE menu button
(5340 IP Phones only). Messages are displayed as first in/first out. If there is more than one message, you can repeatedly press (Message) to scroll through the messages.
2. When the desired message is displayed, press #, or lift the handset for privacy, and then press # to respond. [If your handset is off-hook and you press (Message), you automatically place a call to the party or message center that left the message.]
Canceling Messages Left at Other Extensions
You can cancel messages left at other extensions.
To cancel a message left at another extension:
1. Dial 366 or press (Message), and then press the CANCEL MESSAGE menu button. CANCEL MESSAGE ON EXT # appears.
2. Enter the extension number where you left the message. MESSAGE CANCELED FOR
<name> appears.
Deleting Waiting Inter-Station Messages
You can delete waiting inter-station messages.
NOTE
To delete waiting voice messages, you must connect to your voice mailbox.
To delete waiting inter-station messages:
1. Press (Message) or the VIEW MESSAGE menu button (5340 IP Phones only).
MSG <message information> appears.
2. Press
*
or the DELETE menu button (5340 IP Phones only) to delete the displayed message.
Page 60
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Messages
Using Do-Not-Disturb (DND)
You can use DND to stop calls and pages to your extension. When activated, internal calling parties see your selected DND message. DND does not block queue callbacks, recalls, and incoming external calls. The following table shows the 20 default DND messages. If your system administrator changes your DND messages, you can record the new messages in the
“New Message” column for reference.
Code
Default Message
01 Do-Not-Disturb
02 Leave a Message
03 In Meeting Until
04 In Meeting
05 On Vacation/
Holiday ’Til
06 On Vacation/
Holiday
07 Call Me At
08 At the Doctor
09 On a Trip
10 On Break
New Message Code Default Message New Message
11
15
16
17
Out of Town ‘Til
12 Out of Office
13 Out Until
14 With a Client
With a Guest
Unavailable
In Conference
18 Away from Desk
19 Gone Home
20 Out to Lunch
You can enter a second line of text (up to 20 characters) for DND messages. For example, if you select IN MEETING UNTIL, you can enter “3:30” on the second line. When other internal parties try to call you, their displays show “IN MEETING UNTIL 3:30.”
To turn on DND:
1. Press the DND button. SELECT DND MSG # (01-20) appears.
2. Do one of the following:
•
Press (Up) or (Down) to scroll through the messages.
•
Enter the two-digit number for the DND message from the preceding table.
•
Press the SCROLL menu button (5340 IP Phones only), and then press the
PREVIOUS or NEXT menu buttons to scroll through the list.
3. If applicable, enter the additional text for the DND description. See “Using the Dialpad
Buttons to Enter Characters” on page 22 for dialpad character descriptions.
4. Press (Speaker) or the ACCEPT menu button (5340 IP Phones only).
To turn off DND:
Press the DND button, or press the DND menu button (5340 IP Phones only), and then press DND OFF. DO-NOT-DISTURB OFF appears.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 61
Messages
Using Reminder Messages
You can use Reminder messages to alert you at a selected time, up to 24 hours in advance. At the selected time, the Reminder message signals you with eight short tones and your display shows the message, even if you are on a call.
The following table shows the 20 default Reminder messages. If your system administrator changes your Reminder messages, you can record the new messages in the “New Message” column for reference.
Code
Default Message
01 Meeting
02 Staff Meeting
03 Sales Meeting
04 Cancel Meeting
05 Appointment
06 Place Call
07 Call Client
08 Call Customer
09 Call Home
10 Call Corporate
New Message Code
Default Message
11 Call Engineering
12 Call Marketing
13 Call Accounting
14 Cancel DND
15 Cancel Call Fwd
16 Take Medication
17 Make Reservation
18 Review Schedule
19 Lunch
20 Reminder
New Message
To set a Reminder message:
1. With the handset on-hook, dial 305. SELECT REMINDER MESSAGE # (01-20) appears.
2. Do one of the following:
•
Enter the two-digit number for the Reminder message from the preceding table.
•
Press (Up) or (Down) to scroll through the messages.
3. Press # or the ACCEPT menu button (5340 IP Phones only) to select the message.
4. Enter the time you wish to receive the message in hours and minutes (for example, 0900 or 900 for 9:00). Then press #. The display shows the Reminder message state.
If your system is set for 24-hour format, enter the applicable time (1400 = 2:00 P.M.).
If your system is set for 12-hour format, press 1 for A.M. or 2 for P.M.
To cancel all Reminder message requests:
With the handset on-hook, dial 306. REMINDER MSGS CANCELED appears.
To clear a received Reminder message:
With the handset on-hook, press
*
.
Page 62
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Messages
Paging Other System Users
You can place page announcements through phone speakers or external speakers (if applicable). Your system may use page zones to prevent announcements from transmitting through every phone in the system. Each page zone contains a different combination of extensions and external paging equipment.
Contact your system administrator for page zone information. You can use the following table to save the page zone information for future reference.
Page Zone Name Number Description
Placing a Page Announcement
The following instructions describe how to place a page announcement.
To place a page announcement:
1. Press 7.
2. Enter the page-zone number (0 to 9).
3. Wait for the tone, make your announcement, and then hang up.
Enabling or Disabling the Page Feature
You can enable or disable the Page feature for your extension. If your extension is assigned to more than one page zone, the Page on/off feature code enables or disables your extension for all pages zone (you cannot select individual zones).
To enable or disable paging for your IP phone:
Dial 325 to enable paging. PAGE RECEIVE ON appears. Dial 325 again to disable paging.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 63
Hunt Groups
Hunt Groups
Hunt groups are groups of internal parties (agents) who share a common (hunt group) extension number. Calls can either be placed to the hunt group (using the hunt group extension number) or to a specific agent (using the agent’s extension number). Hunt groups are programmed by the system administrator.
Hunt groups types are either “UCD” or “ACD.”
•
UCD Hunt Groups: Uniform Call Distribution (UCD) agents do not log in to the hunt group to receive calls.
•
ACD Hunt Groups: Automatic Call Distribution (ACD) agents log in to the ACD hunt group to receive calls. Calls are distributed by either Agent IDs or extensions: o Agent IDs: Each agent is assigned an Agent ID number for logging in to the hunt group
(see the next section). Hunt group calls are distributed to logged-in agents according to their Agent ID number instead of their extension number. Agents can log in to any ACD hunt group phone. o Extensions: Hunt group members do not use Agent IDs, and calls are distributed to phones where the agents are logged in.
Logging in to ACD Hunt Groups
You must log in to an ACD hunt group to receive hunt group calls. To stop calls, you either log
out of the ACD hunt group or divert calls. See “Diverting Hunt Group Calls” on page 67 .
NOTES
Only one agent can be logged in to a phone.
If the ACD Agent ID Automatic Connect option is enabled for your hunt group and you are using a headset, you are automatically connected to waiting calls when you log in. The first call you receive after you log in rings until you answer it; however, you are automatically connected to subsequent calls.
To log in to or out of all ACD hunt groups in which you are a member:
Dial 328 to log in to ACD hunt groups followed by your Agent ID, if necessary. AGENT
LOGGED INTO ALL ACDS appears. Dial 328 again to log out of all ACD hunt groups.
To log in to one or more ACD hunt groups:
1. Dial 326. AGENT LOGIN ACD HG # appears.
2. Do one of the following:
•
Enter the ACD hunt group number.
•
Press # to log in to all of your ACD hunt groups.
The display shows AGENT LOGIN AGENT ID.
3. Enter your Agent ID (if applicable), or press # if you do not have an agent ID. The display shows the log in status for one or all hunt groups.
Page 65
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Hunt Groups
Logging out of ACD Hunt Groups
You can log out of all ACD hunt groups at once or log out of each hunt group one at a time.
To log out of one or more ACD hunt group:
Do one of the following:
•
Dial 328 to log out of all of your ACD hunt groups. The display shows AGENT
LOGGED OUT OF ALL ACDS.
•
Dial 327 to log out of one hunt group at a time.
If you were logged in to only one hunt group, the display shows AGENT LOGGED
OUT OF HUNT GROUP <number>.
If you were logged in to more than one hunt group, the display shows AGENT
LOGOUT HG #. Enter the extension number of the ACD hunt group.
Stopping the ACD Hunt Group Wrap-up Timer
Each time you end an ACD hunt group call, a wrap-up timer starts. The default wrap-up time is
15 seconds. Your system administrator can change the wrap-up timer settings.
Until this timer expires, you will not receive another hunt group call; however, you can stop the wrap-up timer to allow calls to your extension.
To stop the wrap-up timer:
With the handset on-hook, dial 329. The display shows ACD WRAP-UP TERMINATED.
Page 66
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Hunt Groups
Other Hunt Group Features
The following features can be used by ACD or UCD hunt groups.
Requesting Agent Help
You can use Agent Help to request help from a designated “Agent Help Extension” (usually your supervisor) during a call. When your request call rings at the Agent Help Extension, the supervisor can join the call or reject the request.
NOTE
Agent Help is not supported on peer-to-peer (P2P) calls. Contact your system administrator for more information.
To use Agent Help:
1. While you are on a hunt group call, press (Special), and then dial 375.
NOTE
If you hear repeating tones, one of the following has occurred:
•
The feature is not available at your IP phone.
•
You already have four parties in your call.
•
Not enough system circuits are currently available.
•
The Agent Help Extension is in DND.
2. If not preprogrammed, dial the Agent Help extension number.
If the Agent Help Extension accepts the call, AGENT HELP IN PROGRESS appears.
If the Agent Help Extension rejects the call, AGENT HELP REJECTED appears.
Diverting Hunt Group Calls
You can temporarily divert hunt group calls, preventing hunt group calls to your extension.
To divert hunt group calls:
Dial 324 to divert calls. The display shows the feature state DIVERT HUNT GROUP
CALLS. Dial 324 again to program your IP phone to accept calls.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 67
Hunt Groups
Hunt Group Supervisor Features
The following features can be used by hunt group supervisors only.
Accepting or Rejecting Agent Help Calls
Supervisors can accept or reject Agent Help calls.
To accept an Agent Help request:
Answer as usual. Your microphone is automatically muted
.
To reject an Agent Help request:
Dial 376 or press the REJECT HELP menu button (5340 IP Phones only). AGENT HELP
REJECTED appears.
Monitoring Calls
You can use Station Monitor to connect to a hunt-group call and hear both parties, but you cannot be heard by either one. Station Monitor stops if the hunt group member terminates or transfers the call. You can barge-in to or “steal” monitored calls, as described in the following
sections. You can also record the call. See “Using Record-A-Call” on page 50 for more
information about recording calls.
NOTE
Station Monitor is not supported on peer-to-peer (P2P) calls. Contact your system administrator for more information.
To use Station Monitor:
Dial 321 or press the SIL MONITOR menu button (5340 IP Phones only), and then enter the extension number. MONITORING EXT <number> appears. Monitored hunt group members may hear an “activation tone” when the feature is activated.
Stealing Hunt Group Calls
While monitoring a hunt group call, you can “steal” the call from the hunt group member, which disconnects the call from the agent and transfers the call to your extension.
To steal a hunt group call:
Dial 387 or press the STEAL menu button (5340 IP Phones only). CALL STOLEN FROM
EXT <number> appears.
Page 68
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Hunt Groups
Using Barge-In
While monitoring a hunt group call, you can use Barge-In to join the call.
To monitor and/or barge in on a call:
1. To use the speakerphone: While on hook, dial 321. You hear a confirmation tone.
ENTER EXT TO MONITOR appears.
To use the handset: Lift the handset, and then dial 321. You hear a confirmation tone.
ENTER EXT TO MONITOR appears.
2. Dial the extension number (or press the lit station speed-dial or DSS/BLF button) of the station to be monitored. You are automatically connected to the call. MONITORING
(extension number) appears.
3. While silent monitoring a call, you have the following options:
•
To barge in on a call, dial 386 or press the BARGE-IN menu button (5340 IP
Phones only). BARGE-IN IN PROGRESS appears. While on a call, you can monitor, record, or steal the call by entering the appropriate feature code or by pressing the appropriate menu button (5340 IP Phones only).
To return to silent monitoring of the call, dial 386 again or press the MONITOR menu button (5340 IP Phones only).
To record the call, dial 385 or press the RECORD CALL button (5340 IP Phones only).
•
To record a call, dial 385 or press the RECORD menu button (5340 IP Phones only). MONITORING (extension number) appears. While on a call, you can monitor or steal the call by entering the appropriate feature code or by pressing the appropriate menu button (5340 IP Phones only).
To stop recording the call, dial 385 again or press the STOP RECORDING menu button (5340 IP Phones only).
•
To steal a call, dial 387 or press the STEAL menu button (5340 IP Phones only).
CALL STOLEN FROM (extension number) appears. The hunt group member’s display shows CALL STOLEN BY (extension number). After the supervisor steals the call, the call becomes a regular call. While on a call, you can record the call by dialing 385 or by pressing the RECORD menu button (5340 IP Phones only).
•
To join and record a call, dial 386 or press the JOIN AND RECORD menu button, and then dial 385. BARGE-IN IN PROGRESS appears. While on a call, the supervisor can monitor, stop recording, or steal the call by entering the appropriate feature code, or by pressing the appropriate menu button (5340 IP Phones only).
To stop recording the call, dial 385 again, or press the MONITOR or STOP
RECORDING menu button (5340 IP Phones only).
4. To terminate any of the features: If off hook, hang up or enter the specific feature code of the feature you want to terminate. If on hook, press the Speaker button or enter the specific feature code of the feature you want to terminate.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 69
Cordless Devices
Cordless Devices
NOTE
The cordless devices are supported by the 5330/5340 IP Phones only. The 5320 IP
Phone does not support a cordless module or cordless devices.
You can use the cordless handset and cordless headset to move around within your office or adjacent offices. The cordless headset and handset are optional accessories, ordered separately. For more information, contact your system administrator or local Mitel provider. Both cordless devices connect to your IP phone through the cordless module, which attaches to the back of the IP phone. The cordless headset rests and recharges in a headset cradle that attaches to the side of the IP phone. The cordless handset recharges in the handset cradle.
The Cordless Devices Application provides access to the configuration settings and information
The cordless module is shown here. The IP phone features are explained below.
1
2
5
3
4
Feature Function
1 – Cordless Module
2 – Cordless Headset
3 – Cordless Headset Charging
Cradle
4 – Cordless Handset Charging
Cover
5 – Cordless Handset
Attached to the back of the IP phone, the module contains a light-emitting diode (LED) indicating that a cordless device is in use; also indicates the pairing of module and a cordless device.
Cordless handsfree operation for calls. If you are using the cordless headset, you do not need to use the handset.
Provides power to recharge the cordless headset battery.
Provides power to recharge the cordless handset battery.
Replaces the cover supplied with the IP phone for corded handsets.
Cordless operation for handset calls. (You can transfer from the IP phone handset to the cordless headset at any time.)
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 71
Cordless Devices
Cordless Module
The cordless module is shown here.
CAUTION
Phone Damage Hazard. Attempting to remove the back plate on the IP phone to install the cordless module before disconnecting the IP phone power supply may damage the IP phone. For information about installing the cordless module, refer to the installation documentation that is shipped with the unit.
1
2
Feature
1 – Cordless Module pairing button
2 – Cordless Headset Cradle cable
Function
Initiates pairing between the cordless module and a cordless device.
Connects to the cordless module to provide power to the charging cradle.
Handset and Headset Combinations
The following combinations of corded and cordless headset and handset are supported on the
5330/5340 IP Phone:
•
Corded handset only
•
Corded headset only
•
Corded handset and corded headset
•
Cordless handset only
•
Cordless headset only
•
Cordless handset and cordless headset
•
Corded handset and cordless headset
•
Corded headset and cordless handset
Page 72
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Cordless Devices
Pairing the Cordless Module and Devices
Before using the cordless handset or headset, each device must establish communication with the cordless module using a procedure called pairing.
NOTES
An IP phone can have only one cordless handset and one cordless headset.
A cordless handset or headset can be paired with only one IP phone at a time.
Pairing a new cordless handset or headset with the IP phone overwrites the configuration of any previous handset or headset.
Pairing cannot be performed when the cordless device is already in use.
To pair a cordless device:
1. Ensure that the battery of the cordless device to be paired is at least partially charged.
2. Press and hold down the pairing button on the back of the cordless module
(see
) for five seconds to activate phone pairing mode. The LED on the cordless module blinks. The Cordless Devices application opens on the IP phone and prompts you to press the pairing button on the cordless device.
3. Press and hold down the hookswitch on the cordless handset or headset for five seconds to activate the device pairing mode. The LED on the cordless device blinks.
After a moment, the Cordless Devices application displays information for the device to be paired.
displaying the paired device name and its battery level indicator and the number of devices paired.
To unpair a cordless device:
2. Press the device name you want to unpair. The information screen for the selected device appears.
the device is unpaired, removed from the display, and can no longer be used to interact with the IP phone.
The cordless module has a blue LED that indicates the current status of the module. The handset is blinking, when the LED is on and off for an equal amount of time.
Blue LED
Solid
Blinking
Off
Solid for two seconds
Function
Audio is active between the module and either the handset or headset.
Pairing mode is active or a firmware upgrade is in progress.
No audio is active.
Pairing is successful.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 73
Cordless Devices
Using a Cordless Device as a Remote Control
When not being used to talk, the cordless handset/headset buttons can act as a remote control device to change display contrast, volume, and mute settings on the host IP phone. For example, in a remote handsfree conference setting, you can use the Volume and Mute buttons on a cordless device to adjust speaker levels and mute the microphone on an IP phone that is not within his reach.
Alerting Tones and LEDs
The cordless devices provide the following alerting tones:
Feature Function
Mute key on cordless device ON/OFF Two-pitch tone occurs immediately. Reminder tone occurs 30 seconds after activation and then regularly until deactivated
Mute key on phone ON/OFF No immediate tone. Reminder tone occurs 30 seconds after activation and then regularly until deactivated.
Low battery (within 10 minutes left)
Low battery (within 2 minutes left)
Out of range
Three beeps and 20 second pause repeated three times.
Three rapid beeps and 1.5 second pause repeated three times.
Repetitive 3-pitch tone until you are back in range.
NOTES
Audio indications are heard in the handset only when it is in use, and may interrupt voice transmission.
If you are out of range for more than 10 seconds, any call that is in progress is dropped and not recovered.
Low Battery Level
When the battery of a cordless device reaches a near-critical level, the IP phone displays a warning. Until the battery is recharged (or until it becomes fully discharged), the warning is repeated at each new call. To continue with a call while charging the cordless device, switch to speakerphone and then cradle the cordless device.
Page 74
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Cordless Devices
Cordless Handset
The cordless handset, shown below provides office mobility, allowing you to place and answer calls while away from your desk. Replacing the standard corded handset, the cordless handset contains a chargeable battery that charges in the handset cradle when not in use. To use the cordless handset, you must pair the handset with the IP phone. For more information, see
Cordless Handset Features
Cordless handset elements are shown in the following table.
Feature
1 – Cordless Handset LED
2 – Hookswitch and pairing button
3 – Mute button
4 – Volume Up and Down button
Function
Blue: LED indicating the status of the handset.
Green: LED indicating the status of the handset battery.
For more information see
.
Lifting the handset from the cradle activates the handset. If the handset is already out of the cradle, pressing the hookswitch takes the handset off-hook.
Pressing the hookswitch again returns it to on-hook.
Pressing the hookswitch while on a speakerphone all, moves the call to the cordless handset.
Mute allows you to turn the microphone off during a call.
Up and Down buttons provide volume control for the ringer and handset/headset.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 75
Cordless Devices
Answering Calls
The following instructions describe how to answer a call.
To answer a call:
Do one of the following:
•
Lift the cordless handset.
•
If the handset is already out of the cradle, press the hookswitch button on the handset.
Hanging Up
If you are out of range for more than 10 seconds, any call that is in progress is dropped and not recovered.
To hang up:
Do one of the following:
•
Replace the cordless handset in the cradle.
•
Press the hookswitch button on the handset.
Cordless Handset LEDs
The handset has two LEDs:
•
Blue – indicates the operational status of the handset.
•
Green – indicates the status of the electrical charge of the battery.
The handset is blinking, when the LED is on and off for an equal amount of time. The handset is winking, when the LED is on for a short period of time and off for a longer period of time.
LED Color
Blue
Green
Solid
Blinking
Winking
LED State
Off
Solid
Blinking
Off
Indicates:
Handset is muted.
Handset is in pairing mode.
Active audio path between handset and module.
No audio path between handset and module.
Battery is dead.
Battery is fully charged.
Battery is charging.
When handset is cradled and the LED does not flash or illuminate, this indicates an absence of battery power. During the first
30 – 60 minutes that the light is off, the battery may be trickle charging. If that is the case, the LED resumes normal behavior within that 60–minute period. If the LED remains off for more than 60 minutes, then either the battery is no longer chargeable or there is a problem in the charging circuit.
NOTE
It is normal for the handset LED to cycle between blinking and solid as battery charge is maintained.
Page 76
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Cordless Devices
Cordless Headset
The cordless headset offers the same capability as the cordless handset to make and answer phone calls away from your desk, while adding the convenience of hands-free operation.
When not in use, the cordless headset sits in the headset charging cradle. For more information
on alerting tones and LEDs, see “Alerting Tones and LEDs” on page 74 .
To use the cordless headset, you must pair the headset with the IP phone. For more
information, see “Pairing the Cordless Module and Devices” on page 73
.
Cordless Headset Features
The cordless headset is shown here.
41
3
2
5
1
1 – Microphone
2 – Boom arm
3 – Linked Indicator (LED)
4 – Volume control
5 – Hookswitch and pairing button
Answering Calls
The following instructions describe how to answer a call.
To answer a call:
Do one of the following:
•
Lift the cordless headset from the cradle.
•
If the headset is already out of the cradle, press the hookswitch button on the headset.
Hanging Up
If you are out of range for more than 10 seconds, any call that is in progress is dropped and not recovered.
To hang up:
Do one of the following:
•
Replace the cordless headset in the cradle.
•
If the headset is already out of the cradle, press the hookswitch button on the headset.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 77
Cordless Devices
Cordless Headset LEDs
There are two LEDs associated with the cordless headset:
•
Blue – Indicates the operational status of the headset
•
Green – Indicates the status of the electrical charge of the battery
The handset is blinking, when the LED is on and off for an equal amount of time. The handset is winking, when the LED is on for a short period of time and off for a longer period of time.
Led Color
Blue (on headset)
Green (on cradle)
LED State
Solid
Blinking
Winking
Solid for 2 seconds
Solid
Blinking
Winking
Off
Indicates
Headset microphone is muted.
Headset is in pairing mode.
Active audio path between Headset and
Module.
Indicates one of the following:
•
Pairing successful
•
New battery installed
Battery is fully charged.
Battery is charging.
Indicates low voltage when headset is uncradled.
When headset is cradled, indicates battery is not charging.
Using the Cordless Devices Application
The Cordless Devices Application provides access to module information and pairing for handset or headsets.
To access the Cordless Devices Application, do one of the following:
•
Press (Applications), and then press Cordless Devices.
•
Press a feature button (key) you have programmed as the Cordless Devices Application key.
For information about programming feature keys, see
NOTE
When the pairing button on the Cordless Module is pressed, or when the battery level of a cordless accessory is critically low, the IP phone will automatically open the Cordless Devices Application.
Viewing Cordless Module Information
You can use the Cordless Module Application to view protocol, firmware, and hardware information about the module.
To view cordless module information:
Page 78
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Troubleshooting
Troubleshooting
The following sections can help you solve problems that you may be experiencing with your IP phone. Troubleshooting topics include:
•
Contact Information: Information about system administrator contacts.
•
Error Messages: Error messages and descriptions.
•
Troubleshooting Tips: Possible problems and methods to solve them.
Contact Information
Your system administrator can help you with items such as changing your settings or modifying phone features. System administrator duties include:
•
Adding new user accounts.
•
Setting the date and time.
•
Programming System Speed-Dial numbers.
•
Making database changes, such as changing user names and extension numbers.
Contact your system administrator with questions that are not covered in this user guide. If you need further assistance, you can find provider information on the Mitel Web site
(www.mitel.com). All sales, service, and support are coordinated at the local level.
Error Messages
The following error messages may appear when using your IP phone.
Message
CANNOT ACCESS FEATURE
CANNOT ACCESS RESERVED
FEATURE
INVALID FEATURE CODE
INVALID EXTENSION NUMBER
NO UPDATE PERFORMED
Reason
The feature is enabled but other feature-related conditions were not met. Make sure that all featurerelated conditions are met and retry.
Your system does not support the feature. Contact your system administrator for more information.
The feature code entered does not exist. Retry using the correct feature code (see
).
The extension number entered does not exist. Retry using a valid extension number.
The feature was not completed or one or more feature conditions were not met.
Page 79
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Troubleshooting
Troubleshooting Tips
The following table includes troubleshooting tips for phone and system features.
NOTE
You can often correct problems that you may be experiencing by resetting the IP
phone to the default settings. See “Resetting the IP Phone to the Default Settings” on page 28
.
Problem Possible Solution
The IP phone is not working properly. Contact your system administrator.
I cannot use one or more of the features described in this guide.
The feature may not be enabled. Contact your system administrator for more information.
I cannot program System Speed-Dial numbers.
Your system administrator programs System Speed
Dial numbers.
I cannot change the time and date on the phone display.
Your system administrator programs the time and date.
Contact your system administrator if you notice that the date and time are incorrect.
I am experiencing audio problems on my phone such as echo, distorted sound, or choppiness.
Contact your system administrator if you are having audio problems.
The name on the display is incorrect. Your system administrator assigns display names.
I cannot use the local telephone company star codes (for example,
*82, *69) when I press the Outgoing button or use the Outgoing Call access code (8 is the default code) when calling an external number.
Rather than pressing the Outgoing button or 8 to access an outside line, you must dial a Select Line
Group number before you can use the star codes. For example, if your system is using the default Select Line
Group numbers, dial 92001 to access that line. After you have dial tone, you can dial the star code and the number.
I cannot use the Agent Help, Recorda-Call, or Station Monitor feature.
If your system uses Peer-to-Peer (P2P) audio, you cannot use these features when you are on a P2P call.
Contact your system administrator for more information.
I cannot program a Station Speed
Dial number to the button I want.
Before assigning the speed-dial number to a programmable button, you must store the number with either a Station Speed-Dial bin.
Page 80
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Troubleshooting
Problem Possible Solution
When I try to use the Dynamic
Extension Express – Handoff feature
(388), the display shows NO CALL
TO HANDOFF.
The NO CALL TO HANDOFF display indicates that the call cannot be handed off because one of the following may have occurred:
•
You tried to use the Handoff feature on a call that has not been routed by Dynamic Extension
Express.
•
You tried to use the Handoff feature on a call that the system has not yet recognized as a valid call.
•
You tried to use the Handoff feature on an unsupported extension. The Handoff feature is supported on your main extension only.
•
You tried to use the Handoff feature on a phantom extension. The Handoff feature is not supported on phantom extensions.
•
You entered the handoff feature code at the exact time the other party on the call disconnected.
•
The call was terminated for some reason.
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Page 81
Index
Index
Symbols
5310 IP Conference Unit, using 9
A
ACD Hunt Group Wrap-Up Timer, stopping 66
ACD Hunt Groups
Agent Help
Agent Help Calls, accepting or rejecting 68
Angle
Angle, adjusting and viewing 15
Automatic Call Access, using 31
Automatic Trunk Answer, using 32
B
Background Music, listening 28
Button Assignments, viewing 28
C
Call Forward
Mitel
®
5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Callback (Queuing the Phone), requesting 34
Caller ID Information
Calls
conference 48 conference, placing 48
external 35 external, placing 35
picking up (reverse transferring) 43
waiting 31 waiting, answering 31
Calls to External Numbers, transferring 43
Calls to Other Extensions, transferring 43
Calls Using the Analog Button, making and answering 12
Calls Using the Failover Mode, making and answering 13
Characters, entering dialpad 22
Codes
default system access 25 feature, default 25
Conference and Placing all Parties on Hold, ending 49
Conference Calls
adding a party to 48 dropping out of 48
Conference Controller Application, accessing/exiting 9
Conference Unit On and Off, turning 9
Page 83
Index
Conference Unit Volume, adjusting 9
Conference Unit, presentation mode, placing 10
Configuration Assistant 53 accessing 53 using 53
Cordless Device as a Remote Control, using 74
Cordless Devices
Cordless Devices Application, using 78
Cordless Handset 75 features 75
Cordless Headset 77 features 77
Cordless Module and Devices, pairing 73
Cordless Module Information, viewing 78
Cordless Modules and Devices, pairing 73
D
Default
access codes 25 feature codes 25
programmable buttons, resetting to 28 settings, returning the phone to 28
Dialpad
Dialpad Buttons to Enter Characters, using 22
Display Contrast and Brightness, adjusting 16
Page 84
Do-Not-Disturb (DND), using 61
Dropping Out of a Conference 48
Dynamic Extension Express
enabling and disabling 47 handoff 47
E
Emergency Calls
placing 33 using the LIM Line, placing 33
Enabling or Disabling the Page Feature 63
Ending a Conference and Placing all Parties on Hold 49
Error
External Numbers, redialing 35
F
Feature
Features to Programmable Buttons, assigning 24
G
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
H
I
off-hook 7 off-hook, on-hook 7 on-hook 7
Handset and Headset Combinations 72
Handsfree Mode
Hold
Hunt Group Calls
Hunt Group Supervisor Features 68
Hunt Groups
accepting or rejecting Agent Help 68
Automatic Call Distribution (ACD) 65
calls
Uniform Call Distribution (UCD) 65
Inter-Station Messages, deleting 60
IP Phone to the Default Settings, resetting 28
K
Keymaps
Page 85
L
Line Interface Module (LIM), using 11
Logging out of ACD Hunt Groups, logging out 66
M
Manual Call Forwarding Settings, changing 55, 57
Menu Buttons (5340 IP Phones only) 6
Messages
replying to 60 viewing 60 viewing and responding 60 voice, listening to 60
Messages at Other Extensions, leaving 59
Messages Left at Other Extensions, canceling 60
Messages, viewing and responding 60
N
Numbers
redialing 35 redialing external 35
O
Outgoing Call Access Code 33, 35
Index
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Index
P
Paging
enabling or disabling 63 other system users 63 using 63
Paging Feature, enabling or disabling 63
Password, Remote Programming
Phone
default settings, returning to 28
features
dialpad buttons 5 feature buttons 5
menu buttons (5340 IP Phone) 6
Ring/Message Indicator 4 speaker 4, 6
Phone to the Default Settings, resetting 28
resetting 28 resetting to default values 28
Page 86
R
change DND settings, using 54, 57
forward calls, using 54, 55, 57
password
Reverse Transfer (Call Pickup), using 43
Ring Intercom Always, using 41
Ring Tone
S
Secondary Extension Buttons, using 52
Settings, returning to default 28
Speakerphone
Speed Dial
entries to programmable buttons, assigning 38
station, using 36 system, using 36 using 36
Speed-Dial Numbers to Programmable Buttons
STAR Codes, telephone company 80
Station Messages
Station Password, changing 53, 58
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Index
Station Speed Dial numbers
Station Speed-Dial Numbers
System
System Information, viewing 44
T
Text Size on the Display, changing 18
Tips
Transferring Calls 43 transferring 43
V
Voice Messages
W
Page 87
Mitel ® 5320/5330/5340 IP Phone User Guide – Issue 4, June 2010
Part No. 550.8123
Issue 4, June 2010
A661/9234A
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Front Cover
- 3 5320/5330/5340 IP Phone Quick Reference Guide
- 5 Notice
- 6 Important Safety Instructions and Precautions
- 6 Programming Emergency Numbers
- 6 Safety Notices
- 6 Maintenance and Repair
- 7 Power Requirements
- 7 Software Updates
- 7 Product Disposal Instructions
- 8 Phone Usage
- 9 Notice to Canadian Customers
- 9 Notice to U.S. Customers
- 9 Notice to European Customers
- 11 Contents
- 17 Getting Started
- 17 Welcome
- 17 About Your IP Phone
- 18 5320/5330 IP Phone Features
- 19 5340 IP Phone Features
- 20 Phone Feature Descriptions
- 23 Phone Signals
- 23 Comfort and Safety Tips
- 24 Viewing the Phone Information
- 24 Using a Headset
- 25 Using the 5310 IP Conference Unit
- 27 Using the Line Interface Module (LIM)
- 28 Making and Answering Calls Using the Analog Button
- 29 Making and Answering Calls Using the Failover Mode
- 31 Personalizing Your Phone
- 31 Adjusting the Viewing Angle
- 32 Changing Volume Levels
- 32 Changing the Ring Tone
- 32 Adjusting the Display Contrast and Brightness
- 33 Changing the Language
- 34 Changing the Text Size on the Display
- 35 Using the Screen Saver
- 37 Specifying Audio Feedback Options
- 38 Using the Dialpad Buttons to Enter Characters
- 40 Using Programmable Buttons
- 41 Default Access Codes
- 41 Default Feature Codes
- 44 Listening to Background Music
- 44 Viewing Button Assignments
- 44 Resetting Programmable Buttons
- 44 Resetting the IP Phone to the Default Settings
- 45 Switching Keymaps
- 45 Activating Door Relay
- 47 Answering and Placing Calls
- 47 Answering Calls
- 47 Answering Waiting Calls
- 47 Using Automatic Call Access
- 48 Redirecting Calls
- 48 Using Automatic Trunk Answer
- 49 Placing Calls
- 49 Placing Emergency Calls
- 49 Placing Emergency Calls using the LIM Line
- 50 Placing Internal Calls
- 51 Placing External Calls
- 51 Redialing a Number
- 52 Using Speed Dial
- 52 Using System Speed Dial
- 52 Using Station Speed Dial
- 55 Using the Directory
- 56 Using Account Codes
- 57 Call Features
- 57 Using Handsfree Mode
- 57 Using Ring Intercom Always
- 57 Using Mute
- 58 Placing Calls On Hold
- 58 Entering a Hookflash
- 59 Transferring Calls
- 59 Transferring Calls to Other Extensions
- 59 Transferring Calls to External Numbers
- 59 Using Reverse Transfer
- 60 Viewing Your System Information
- 60 Viewing Caller ID Information
- 61 Forwarding Calls
- 61 Manual Call Forwarding
- 61 System Forwarding
- 62 Using Dynamic Extension Express
- 64 Placing Conference Calls
- 64 Adding a Conference Party
- 64 Transferring a Conference
- 64 Dropping Out of a Conference
- 65 Ending a Conference and Placing all Parties on Hold
- 66 Using Record-A-Call
- 66 Using Group Listen
- 67 Using Call Logging
- 68 Using Secondary Extension Buttons
- 69 Using Configuration Assistant
- 69 Changing Your Station Password
- 69 Accessing Configuration Assistant
- 70 Changing the Dynamic Extension Express Settings
- 70 Changing the DND Settings
- 71 Changing the Manual Call Forwarding Settings
- 72 Using Remote Programming
- 72 Changing the Dynamic Extension Express Settings
- 73 Changing the DND Settings
- 73 Changing the Manual Call Forwarding Settings
- 74 Changing Your Station Password
- 75 Messages
- 75 Leaving Messages at Other Extensions
- 76 Viewing and Responding to Messages
- 76 Canceling Messages Left at Other Extensions
- 76 Deleting Waiting Inter-Station Messages
- 77 Using Do-Not-Disturb (DND)
- 78 Using Reminder Messages
- 79 Paging Other System Users
- 79 Placing a Page Announcement
- 79 Enabling or Disabling the Page Feature
- 81 Hunt Groups
- 81 Logging in to ACD Hunt Groups
- 82 Logging out of ACD Hunt Groups
- 82 Stopping the ACD Hunt Group Wrap-up Timer
- 83 Other Hunt Group Features
- 83 Requesting Agent Help
- 83 Diverting Hunt Group Calls
- 84 Hunt Group Supervisor Features
- 84 Accepting or Rejecting Agent Help Calls
- 84 Monitoring Calls
- 84 Stealing Hunt Group Calls
- 85 Using Barge-In
- 87 Cordless Devices
- 88 Cordless Module
- 88 Handset and Headset Combinations
- 89 Pairing the Cordless Module and Devices
- 90 Using a Cordless Device as a Remote Control
- 90 Alerting Tones and LEDs
- 90 Low Battery Level
- 91 Cordless Handset
- 91 Cordless Handset Features
- 92 Answering Calls
- 92 Hanging Up
- 92 Cordless Handset LEDs
- 93 Cordless Headset
- 93 Cordless Headset Features
- 93 Answering Calls
- 93 Hanging Up
- 94 Cordless Headset LEDs
- 94 Using the Cordless Devices Application
- 95 Troubleshooting
- 95 Contact Information
- 95 Error Messages
- 96 Troubleshooting Tips
- 99 Index
- 106 Back Cover