DWG875/DWG875T - Wireless Voice Gateway User manual

DWG875/DWG875T - Wireless Voice Gateway
User manual
CAUTION
CAUTION
Disconnect power before
To ensure reliable operation and to prevent
servicing.
overheating, provide adequate ventilation for this
modem and keep it away from heat sources. Do
not locate near heat registers or other
This device is intended for
heat-producing equipment. Provide for free air
indoor operation only.
flow around the Wireless Voice Gateway and its
Telephone jacks Line 1
power supply.
and Line 2 must not be
connected to outside
wiring.
This symbol means that your inoperative electronic appliance must be collected separately and
not mixed with the household waste. The European Union has implemented a specific collection
and recycling system for which producers' are responsible.
This appliance has been designed and manufactured with high quality materials and components
that can be recycled and reused. Electrical and electronic appliances are liable to contain parts
that are necessary in order for the system to work properly but which can become a health and
environmental hazard if they are not handled or disposed of in the proper way. Consequently,
please do not throw out your inoperative appliance with the household waste.
If you are the owner of the appliance, you must deposit it at the appropriate local collection point
or leave it with the vendor when buying a new appliance.
- If you are a professional user, please follow your supplier's instructions.
- If the appliance is rented to you or left in your care, please contact your service provider.
Help us protect the environment in which we live !
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device mat not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
i
Illustrations contained in this document are for representation only.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from thatto which the receiver is
connected.
-
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor environment.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1
through 11.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
ii
Illustrations contained in this document are for representation only.
NORTH AMERICAN CABLE INSTALLER:
This reminder is provided to call your attention to Article 820.93 of the National Electrical Code (Section
54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the grounding system of the building as
close to the point of cable entry as practical.
PacketCable and DOCSIS compliant
The Thomson DWG875/DWG875T is a voice-capable cable modem, which provides broadband Internet
access and telephone capability all in one unit! Also referred to as an Embedded Media Terminal
Adapter (EMTA), this cable modem connects to cable systems using DOCSIS and PacketCable standards.
(Check with your cable operator for compatibility.)
The Thomson DWG875/DWG875T offers a high-speed connection to the Internet using an Ethernet
connection.
If you have subscribed to telephone service from your cable operator, you will be able to place regular
phone calls using your home phone(s) and/or fax machine. The Thomson DWG875/DWG875T provides
two RJ-11 connectors for your phone or home phone system, allowing one or two line service.
Operating Information
Operating Temperature:
0˚ to 40˚ C
Storage Temperature:
-40˚ to 70˚ C
Humidity:
5% ~ 95% non-condensing
(32˚ to 104˚ F)
(-40° to 158° F)
If you purchased this product at a retail outlet, please read the following:
Product Information
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here
and record the serial and model numbers in case you need them. The numbers are located on the
bottom of the product.
Model No.
____________________________Serial No ________________________________
Purchase Date:
________________________Dealer/Address/Phone: _________________________
iii
Illustrations contained in this document are for representation only.
Table of Contents
Chapter 1: Connections and Setup ........................................................................................... 5
Introduction ............................................................................................................................ 5
Wireless Voice Gateway Features ....................................................................................... 5
What’s on the CD-ROM ...................................................................................................... 6
Computer Requirements.................................................................................................... 7
Wireless Voice Gateway Overview ............................................................................................. 8
Front Panel .......................................................................................................................... 8
Rear Panel ......................................................................................................................... 11
Relationship among the Devices ............................................................................................ 13
What the Modem Does .................................................................................................... 13
What the Modem Needs to Do Its Job............................................................................... 14
Contact Your Local Cable Company ................................................................................. 15
Connecting the Wireless Voice Gateway to a Single Computer ................................................ 16
Attaching the Cable TV Wire to the Wireless Voice Gateway ............................................. 16
Important Connection Information .................................................................................. 17
Ethernet Connection to a Computer................................................................................. 18
Connecting More Than A Computer to the Wireless Voice Gateway ........................................ 19
Telephone or Fax Connection ................................................................................................ 20
Turning on the Wireless Voice Gateway .................................................................................. 21
Chapter 2: WEB Configuration ................................................................................................ 22
Accessing the Web Configuration........................................................................................... 22
Outline of Web Manager .................................................................................................. 23
Warning message to change the password ...................................................................... 24
Gateway – Status Web Page Group ......................................................................................... 25
1. Software ...................................................................................................................... 25
1
Illustrations contained in this document are for representation only.
Table of Contents
2. Connection.................................................................................................................. 26
3. Password..................................................................................................................... 27
4. Diagnostics ................................................................................................................. 30
5. Event Log .................................................................................................................... 31
6. Backup/Restore ........................................................................................................... 32
Gateway – Network Web Page Group ...................................................................................... 33
1. LAN ............................................................................................................................. 33
2. WAN ............................................................................................................................ 34
3. Computers .................................................................................................................. 35
4. DDNS - Dynamic DNS service ....................................................................................... 36
5. Time server ................................................................................................................. 37
Gateway – Advanced Web Page Group .................................................................................... 38
1. Options ....................................................................................................................... 38
2. IP Filtering ................................................................................................................... 40
3. MAC Filtering .............................................................................................................. 41
4. Port Filtering ............................................................................................................... 42
5. Forwarding .................................................................................................................. 43
6. Port Triggers ............................................................................................................... 44
7. DMZ Host .................................................................................................................... 45
8. RIP (Routing Information Protocol) Setup ..................................................................... 46
Gateway – Firewall Web Page Group ....................................................................................... 47
1. Web Content Filtering .................................................................................................. 47
2. TOD Filtering............................................................................................................... 48
3. Local Log and Remote Log........................................................................................... 49
Gateway – Parental Control Web Page Group .......................................................................... 50
2
Illustrations contained in this document are for representation only.
Table of Contents
1. Basic ........................................................................................................................... 50
Gateway – Wireless Web Page Group ...................................................................................... 51
1. 802.11b/g/n Radio ..................................................................................................... 52
2. 802.11b/g/n Primary Network..................................................................................... 54
3. Guest Network ............................................................................................................ 63
4. Access Control ............................................................................................................ 64
5. Bridging ...................................................................................................................... 65
6. 802.11e QoS (WMM) Settings....................................................................................... 66
VoIP – Basic Web Page Group ................................................................................................. 67
1. Basic LAN .................................................................................................................... 67
2. Hardware Info ............................................................................................................. 68
3. Event Log .................................................................................................................... 69
4. CM State ..................................................................................................................... 71
Chapter 3: Networking........................................................................................................... 73
Communications ............................................................................................................. 73
Type of Communication .................................................................................................. 73
Cable Modem (CM) Section .............................................................................................. 74
Networking Section ......................................................................................................... 74
Three Networking Modes................................................................................................. 75
Cable Modem (CM) Mode................................................................................................. 75
Residential Gateway (RG) Mode ........................................................................................ 77
Chapter 4: Additional Information ......................................................................................... 79
Frequently Asked Questions .................................................................................................. 79
General Troubleshooting ....................................................................................................... 81
Service Information ................................................................................................................ 83
3
Illustrations contained in this document are for representation only.
Table of Contents
Glossary ................................................................................................................................ 84
4
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Chapter 1: Connections and Setup
Introduction
Wireless Voice Gateway Features
• High Speed Data Service Solution
• DOCSIS 3.0 cable modem
• Giga Ethernet router with 4x Standard RJ-45 connectors for 10/100/1000Mbps. Auto-negotiation
and MDIS functions
• Wi-Fi 802.11b/g/n wireless connection
• Wireless security: multiple SSID and WPS solution
• Two RJ-11 Foreign Exchange Station (FXS) ports for phone and fax connections
• Support simultaneous voice and data communications
• Two simultaneous voice conversations in the different FXS ports with different CODEC: PCM
A-law, PCM-law, G.723.1, G.729, G.729a, G.729e, G.728, G.726, BV16 and BV32
• Echo Cancellation
• Voice Active Detection (VAD)
• DTMF detection and generation
• Comfort Noise Generation (CNG)
• Support V.90 fax and modem services
• RSA and 56 bit DES data encryption security
• SNMP network management support
• IPv4 and IPv6
• Advanced security features
• Support Web pages and private DHCP server for status monitoring
• Clear LED display
• Plug and Play
5
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
What’s on the CD-ROM
Insert the Wireless Voice Gateway CD-ROM into your CD-ROM drive to view troubleshooting tips, the
internal diagnostics, and other valuable information.
CD-ROM Contents:
• Electronic copy of this user’s guide in additional languages (PDF format)
• Adobe Acrobat Reader — application you can load to read PDF format, if you don’t have it loaded
already
• Links to Thomson web site
DOCSIS and PacketCable are trademarks of Cable Television Laboratories, Inc.
6
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Computer Requirements
For the best possible performance from your Wireless Voice Gateway, your personal computer must meet
the following minimum system requirements (note that the minimum requirements may vary by cable
companies):
IBM PC COMPATIBLE
MACINTOSH**
CPU
Pentium preferred
PowerPC or higher
System RAM
16MB (32MB preferred)
24MB (32MB preferred)
Operating System
Windows* NT / 2000 / Me / XP /
Mac OS** 7.6.1 or higher
Vista / Windows 7, Linux
Sound Card
Required for audio on CD-ROM
N/A
Video
VGA or better (SVGA preferred)
VGA or better (SVGA built-in preferred)
CD-ROM Drive
Required
Required
Ethernet
10BaseT , 100BaseT or 1000Mbps 10BaseT , 100BaseT or 1000Mbps
An Ethernet card makes it possible for your computer to pass data to and from
the internet. You must have an Ethernet card and software drivers installed in
your computer. You will also need a standard Ethernet cable to connect the
Ethernet card to your Wireless Voice Gateway.
Software
•
A TCP/IP network protocol for each machine
•
Microsoft Internet Explorer 4.0 or later or Netscape Navigator 4.0 or later.
(5.0 and 4.7 or later, respectively, are strongly recommended.)
* Windows is a trademark of Microsoft Corporation.
** Macintosh and the Mac OS are trademarks of Apple Computer, Inc.
7
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Wireless Voice Gateway Overview
Front Panel
The following illustration shows the front panel of the Wireless Voice Gateway:
8
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
The LEDs on the front panel are described in the table below (from left to right):
Internet
DWG875 /
Ethernet
Power
DWG875T
ON
Boot-up
USB
Wireless
Tel 1
Tel 2
Battery
Description
ON
On
X
ON
ON
X
Power on 0.25 sec
X
X
X
X
X
X
DS
US
Online
1
2
3
4
ON
ON
ON
ON
ON
ON
X
X
X
On
0.25 second
ON
FLASH FLASH FLASH
From power ON to system
initialization complete
Operation
ON
ON
ON
ON
Following system initialization
X
X
X
X
X
X
X
X
X
complete to (before)
1 second
ON
FLASH
OFF
OFF
X
X
X
X
X
X
X
X
X
During DS scanning and
acquiring SYNC
From SYNC completed,
ON
ON
FLASH
OFF
X
X
X
X
X
X
X
X
X
DOCSIS Start-up
receiving UCD to ranging
completed
During DHCP, configuration file
Operation
ON
ON
ON
FLASH
X
X
X
X
X
X
X
X
X
download, registration, and
Baseline Privacy initialization
ON
ON
ON
ON
FLASH FLASH
ON
X
X
X
X
X
X
X
X
X
Operational (NACO=ON)
OFF
X
X
X
X
X
X
X
X
X
Operational (NACO=OFF)
Wait registration with all DS
FLASH FLASH FLASH FLASH FLASH
X
X
X
X
X
X
X
X
and all US – Lights Flash
sequentially from the right to
left
From 1 to 4 DS, from 1 to 4
Channel
X
X
X
X
OFF
X
X
X
X
X
X
X
X
LEDs are ON.
From 5 to 8 DS, From 1 to 4
Bonding
LEDs are flashing
Operation
From 1 to 4 US, from 1 to 4
OFF
X
X
X
X
X
X
X
X
X
X
X
X
LEDs are ON.
Wait registration with all DS
FLASH FLASH FLASH FLASH FLASH
X
X
X
X
X
X
X
X
and all US – Lights Flash
sequentially from the left to
right
9
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Internet
DWG875 /
Ethernet
Power
DWG875T
DS
US
Online
1
2
3
4
USB
Wireless
Tel 1
Tel 2
Battery
Description
MTA
ON
ON
ON
ON
X
X
X
X
X
X
FLASH
OFF
OFF
MTA DHCP
initialization
ON
ON
ON
ON
X
X
X
X
X
X
OFF
FLASH
OFF
MTA SNMP/TFTP
ON
ON
ON
ON
X
X
FLASH FLASH
OFF
RSIP for NCS/Register for SIP
X
X
ON
X
X
X
X
X
X
X
OFF
OFF
OFF
OFF
ON
ON
ON
ON
No Ethernet Link
X
X
X
FLASH FLASH FLASH FLASH
CPE Operation
TX/RX Ethernet Traffic
OFF
ON
X
X
X
X
X
X
X
X
ON
Wireless is disable
X
X
X
FLASH
USB Operation
X
X
X
X
X
X
X
ON
No USB Link
X
X
X
X
FLASH
< CM Normal Operation >
Battery Good
<CM
AC Good
Normal
On
< CM Normal Operation >
Battery Low
Operatio
n>
ON
ON
FLASH
ON
ON
FLASH
AC Good
< CM Normal Operation >
Battery Bad
Both Lines On-Hook
ON
ON
Both Lines Off-Hook
ON
FLASH
ON
ON
FLASH
Both Lines On-Hook
FLASH
Both Lines Off-Hook
ON
ON
ON
FLASH
Both Lines On-Hook
OFF
Both Lines Off-Hook
ON
Both Lines On-Hook
OFF
FLASH
Battery Good
ON
Flash
Off
Off
AC Fail
Both Lines Off-Hook
ON
Battery Low
Tel1 Off-hook, Tel2 On-hook
Tel1 On-hook, Tel2 Off-hook
FLASH
FLASH
Tel1 Off-hook, Tel2 On-hook
Tel1 On-hook, Tel2 Off-hook
FLASH FLASH
AC Fail
Tel1 Off-hook, Tel2 On-hook
Tel1 On-hook, Tel2 Off-hook
FLASH FLASH
FLASH
Tel1 Off-hook, Tel2 On-hook
Tel1 On-hook, Tel2 Off-hook
FLASH FLASH
ON
Flash
USB Link
TX/RX USB Traffic
AC Good
On
Wireless initiate success or
TX/RX Wireless Traffic
OFF
ON
Ethernet Link
Both Lines On-Hook
Off
FLASH
ON
Tel1 Off-hook, Tel2 On-hook
Tel1 On-hook, Tel2 Off-hook
FLASH
Both Lines Off-Hook
AC Fail
Both Lines On-Hook
< All LEDs may be unlit due to lack of battery power>
OFF
Battery Bad
Tel1 Off-hook, Tel2 On-hook
Tel1 On-hook, Tel2 Off-hook
Both Lines Off-Hook
A software download and
SW Download
ON
FLASH FLASH
ON
X
X
X
X
X
X
X
X
X
while updating the FLASH
Operation
memory
10
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Rear Panel
A
TEL1 & TEL2
2x Telephony RJ-11 connectors
B
ETHERNET 1 2 3 4:
4x Ethernet 10/100/1000 Mbps RJ-45 connectors
C
USB Host:
1x USB 2.0 Connector
D
Reset:
1x Reset or reset to factory default this Wireless Voice Gateway
11
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
E
CABLE:
1x F-Connector for the coax cable
F
Power Connector:
1x AC Power Connector
I
WPS & WiFi on/off button: 1x button with two features:
to activate/disable the WiFi, to execute a WPS association
12
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Relationship among the Devices
This illustration shows a cable company that offers DOCSIS and PacketCable-compliant voice/data
services.
What the Modem Does
The Wireless Voice Gateway provides high-speed Internet access as well as cost-effective, toll-quality
telephone voice and fax/modem services over residential, commercial, and education subscribers on
public and private networks via an existing CATV infrastructure. It can inter-operate with the
PacketCable compliant head-end equipment and provide the IP-based voice communications. The IP
traffic can transfer between the Wireless Voice Gateway and DOCSIS compliant head-end equipment.
The data security secures upstream and downstream communications.
13
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
What the Modem Needs to Do Its Job
• The Right Cable Company: Make sure your local cable company provides data services that
use cable TV industry-standard DOCSIS compliant and PacketCable compliant technology.
• The Internet/Telephony Service Provider (ISP/TSP): Your cable company provides you
access to an Internet Service Provider (ISP) and Telephony Service Provider (TSP). The ISP is
your gateway to the Internet and provides you with a pipeline to access Internet content on the
World Wide Web (WWW). The TSP provides you with telephony access to other modems or
other telephony services over the Public Switched Telephone Network (PSTN).
Check with your cable company to make sure you have everything you need to begin; they’ll know if
you need to install special software or re-configure your computer to make your cable internet service
work for you.
14
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Contact Your Local Cable Company
You will need to contact your cable company to establish an Internet account before you can use your
gateway. You should have the following information ready (which you will find on the sticker on the
gateway):
•
The serial number
•
The model number
•
The Cable Modem (CM) Media Access Control (MAC) address
•
The Terminal Adapter (EMTA) MAC address
•
Security information: Service Set IDentifier (SSID), Encryption key / passphrase (WPA2-PSK by
default), channel number. Default values are indicated underneath the modem on the sticker.
Please verify the following with the cable company
•
The cable service to your home supports DOCSIS compliant two-way modem access.
•
Your internet account has been set up. (The Media Terminal Adapter will provide data service if the
cable account is set up but no telephony service is available.)
•
You have a cable outlet near your PC and it is ready for Cable Modem service.
Note: It is important to supply power to the modem at all times. Keeping your modem plugged in will
keep it connected to the Internet. This means that it will always be ready whenever you need.
Important Information
Your cable company should always be consulted before installing a new cable outlet. Do not attempt any
rewiring without contacting your cable company first.
15
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Connecting the Wireless Voice Gateway to a Single Computer
This section of the manual explains how to connect your Wireless Voice Gateway to the USB or Ethernet
port on your computer and install the necessary software. Please refer to Figure 1 to help you connect
your Digital Cable Modem for the best possible connection.
Attaching the Cable TV Wire to the Wireless Voice Gateway
1. Locate the Cable TV wire. You may find it one of three ways:
a.
Connected directly to a TV, a Cable TV converter box, or VCR. The line will be connected to
b.
c.
the jack, which should be labeled either IN, CABLE IN, CATV, CATV IN, etc.
Connected to a wall-mounted cable outlet.
Coming out from under a baseboard heater or other location. See Figure 1 for the wiring
example.
Notes: For optimum performance, be sure to
connect your Wireless Voice Gateway to the first
point the cable enters your home. The splitter
must be rated for at least 1GHz.
Fig. 1: Basic Home Wiring
16
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Important Connection Information
The Wireless Voice Gateway supports Ethernet connection.
Below are important points to remember before you connect the Wireless Voice Gateway.
•
For Ethernet connections, go to page 21.
•
For telephone and fax connections, go to page 23.
If you do not want to use the CD-ROM, follow instructions 1 through 4 to connect the Wireless Voice
Gateway to the Ethernet port on your computer. Instructions must be followed in the order they
appear.
1. Connect one end of the coaxial cable to the cable connection on the wall, and the other end to the
CABLE jack on the Wireless Voice Gateway.
2. Attaching power cord to Wireless Voice Gateway and plug into the AC outlet.
3. Insert the supplied Wireless Voice Gateway CD-ROM. Wait momentarily for the CD window display.
DWG875/DWG875T
Fig. 2: Main screen of CD
4. Close all open applications and dialog boxes, including the CD window.
Note: Some applications may interfere with your Wireless Voice Gateway installation.
17
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Ethernet Connection to a Computer
Make the connection to the modem in the following sequence:
1. Connect one end of the coaxial cable to the cable connection on the wall, and the other end to the
CABLE jack on the Wireless Voice Gateway.
2. Connect the plug from the AC power supply into the POWER AC ADAPTER jack on the Wireless
Voice Gateway, and plug the power supply into an AC outlet.
Note: Use only the power supply that accompanied this unit. Using other adapters may damage the unit.
3. Connect one end of the Ethernet cable to an Ethernet port on the back of your computer, and the
other end to the ETHERNET port on the Wireless Voice Gateway.
Fig.3: Ethernet Connection
18
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Connecting More Than A Computer to the Wireless Voice Gateway
If you need to connect more than one computer to the Wireless Voice Gateway, simply connect the
computers to an Ethernet port on the rear panel.
Fig.4: Multiple-PC Connection
Note: You may need to check with your service provider in order to connect multiple computers.
19
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Telephone or Fax Connection
When properly connected, most telephony devices can be used with the Wireless Voice Gateway just as
with a conventional telephone service. To make a normal telephone call, pick up the handset; listen for a
dial tone, then dial the desired number. For services such as call waiting, use the hook switch (or FLASH
button) to change calls. The following procedures describe some of the possible connection schemes for
using telephony devices with the Wireless Voice Gateway.
1. Connect a standard phone line cord directly from the phone (fax machine, answering machine, caller
ID box, etc.) to one of the LINE jacks on the Wireless Voice Gateway.
2. If there is a phone line in your home which is NOT connected to another telephone service provider,
connect a standard phone line cord from a jack on this line to one of the LINE jacks of the Wireless
Voice Gateway. Connect a standard phone line cord directly from the phone (fax machine, answering
machine, caller ID box, etc.) to one of the other jacks in the house that uses that line.
3. If you have a multi-line telephone, connect a standard phone line cord (not an RJ-14 type line cord)
from the phone to the LINE jacks on the Wireless Voice Gateway. (Other phones can be added to
each line by using standard phone line splitters.
Fig. 5: Phone/Fax Connection
20
Illustrations contained in this document are for representation only.
Chapter 1: Connections and Setup
Turning on the Wireless Voice Gateway
After installing the Wireless Voice Gateway and turn it on for the first time (and each time the modem is
reconnected to the power), it goes through several steps before it can be used. Each of these steps is
represented by a different pattern of flashing lights on the front of the modem.
Note: All indicators flash once before the initialization sequence.
If both DS and US LEDs are flashing sequentially, it means the Wireless Voice Gateway is automatically
updating its system software. Please wait for the lights to stop flashing. You cannot use your modem
during this time. Do not remove the power supply, switch off (on/off switch) or reset the Wireless Voice
Gateway during this process.
21
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Chapter 2: WEB Configuration
To make sure that you can access the Internet successfully, please check the following first.
1.
Make sure the connection (through Ethernet or USB) between the Wireless Voice Gateway and
your computer is OK.
2.
Make sure the TCP/IP protocol is set properly.
3.
Subscribe to a Cable Company.
4.
Make sure appropriate LEDs are turned on for normal operation as noted in the previous
chapter.
Accessing the Web Configuration
The Wireless Voice Gateway offers local management capability through a built in HTTP server and
a number of diagnostic and configuration web pages. You can configure the settings on the web page
and apply them to the device.
Once your host PC is properly configured; please proceed as follows:
1.
Start your web browser and type the private IP address of the Wireless Voice Gateway on the
URL field: 192.168.0.1.
2.
After connecting to the device, you will be prompted to enter username and password. By
default, the username is “ ” (empty) and the password is “admin”.
Fig. 6 Dialogue for Login
If you login successfully, the main page will appear.
Please Note; some of the WEB pages shown later, will differ for different software versions and per service providers instructions.
22
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Outline of Web Manager
The main screen will be shown as below.
Fig. 7 Outline of Web Manager
•
Main Menu: the hyperlinks on the top of the page, including Gateway, VoIP and several
sub-menu items
•
Title: the sidebar on the left side of the page indicates the title of this management interface, e.g.,
Software in this example
•
Main Window: the current workspace of the web management, containing configuration or
status information
For easy navigation, the pages are organized in groups with group in names main menu. Individual
page names within each group are provided in the sidebar. So to navigate to a page, click the group
hyperlink at the top, then the page title on the sidebar.
Your cable company may not support the reporting of some items of information listed on your
gateway’s internal web pages. In such cases, the information field appears blank. This is normal.
23
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Warning message to change the password
At your first connection or while the password is the default one, a warning message is displayed on
the top banner of each Web configuration page. We want to encourage you to change the password in
order to enforce the security of your modem. Please refer to the chapter “Password” page 27 for more
information.
24
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Gateway – Status Web Page Group
1. Software
The information section shows the hardware and software information about your gateway.
The status section of this page shows how long your gateway has operated since last time being
powered up, and some key information the Cable Modem received during the initialization process
with your cable company. If Network Access shows “Allowed,” then your cable company has
configured your gateway to have Internet connectivity. If not, you may not have Internet access, and
should contact your cable company to resolve this.
Fig. 8 Gateway\Status\Software
25
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
2. Connection
This page reports current connection status containing startup procedures, downstream and upstream
status, CM online information, and so on. The information can be useful to your cable company’s
support technician if you’re having problems.
Fig. 9 Gateway\Status\Connection
26
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
3. Password
Forcing end user to change the password
Upon access to the web pages on the CPE side of the router, if the user has not changed the default
web password, a warning message must be displayed in the top banner of the web interface such as
being visible while accessing any tabs.
This warning message informs the user that the default password must be changed:
In the second sentence, “here” is a hyperlink to the password setting page. Clicking on “here” lead to
the display of the password setting page.
More information
By default, the username is empty (“”) and the password is “admin”.
This is set by different actions (non exhaustive list):
- at the manufactory level,
- following a reset factory on the modem,
- following a reset from the operator,
- following a change by the user who wants to come back to the default setting after using its own
settings
When the current password is the default one, the user is strongly encouraged to change the default
web password:
- Once the user logs in the web pages, the password setting page is displayed
- the warning message must be displayed in the top banner of the web interface
- The user can still access to all the web pages even if the password is not changed
- The warning message must be displayed on the top banner of each accessed Web page while the
password is not changed
- The password warning message must be visible while accessing all tabs in a the same web page
- The password warning message is no more displayed on the banners once the default
password has been replaced by a new one.
At your first connection or while the password is the default one, a warning message is displayed on
the top banner of each Web configuration page. We want to encourage you to change the password in
order to enforce the security of your modem.
27
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
The password can be a maximum of 8 characters and is case sensitive. In addition, this page can be
used to restore the gateway to its original factory settings. Use this with caution, as all the settings you
have made will be lost. To perform this reset, set Restore Factory Defaults to Yes and click Apply.
This has the same effect as a factory reset using the rear panel reset switch, where you hold on the
switch for 15 seconds, then release it.
Note: We are always suggesting to modify the password is implementing for Voice Wireless Gateway.
It is a basically protection to access Voice Wireless Gateway.
Fig. 10 Gateway\Status\Password
To change the password: type the password, and re-enter it again.
If the password is accepted, you are required to re log on the web pages:
28
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
If the password is not accepted, an error message is displayed:
Click on try again.
29
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
4. Diagnostics
This page offers basic diagnostic tools for you to utilize when connectivity problems occur. When you
ping an Internet device, you send a packet to its TCP/IP stack, and it sends one back to yours. To use
the ping Test, enter the information needed and press Start Test; the Result will be displayed in the
lower part of the window. Press Abort Test to stop, and Clear Results to clear the result contents.
Note: Firewalls may cause pings to fail but still provide you TCP/IP access to selected devices behind
them. Keep this in mind when pinging a device that may be behind a firewall. Ping is most useful to
verify connectivity with PCs which do not have firewalls, such as the PCs on your LAN side.
Fig. 11 Gateway\Status\Diagnostics
30
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
5. Event Log
This page displays the contents of the SNMP event log. Press “Clear Log” button to clear the logs.
Fig. 12 Gateway\Status\Event Log
31
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
6. Backup/Restore
Backup/Restore Settings : This page allows you to save your current settings locally on your PC, or
to restore settings saved previously. The file name is “GatewaySettings.bin”.
Fig 13 Gateway\Status\Backup/Restore
32
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Gateway – Network Web Page Group
1. LAN
You can activate the DHCP server function for the LAN on this page.
With this activated function,
• your cable company’s DHCP server provides one IP address for your gateway,
• and your gateway’s DHCP server provides IP addresses, starting at the address you set in IP
Address on the LAN page, to your PCs. A DHCP server leases an IP address with an expiration
time.
To change the lowest IP address that your gateway will issue to your PCs, enter it into the IP Address
box and then click Apply.
IP Address and Subnet Mask:
A private IP address and Subnet Mask for LAN sub netting.
For example 192.168.0.1./ 255.255.255.0.
DHCP Server:
•
•
•
Select the check point of “Yes” or “No” to enable or disable a simple DHCP server for LAN.
Configure the IP address numbers for the DHCP server with “lease pool start” and “lease
pool end”.
Configure the IP address lease time with “lease time” for DHCP server. Default value is
604800 seconds.
Fig. 14 Gateway\Network\LAN
33
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
2. WAN
You can configure the optional internal DHCP server for the WAN on this page. This can be required
by some ISP providers.
Select different WAN Connection Type will lead to different contents. Take the WAN connection
type-DHCP for example, you can release and renew the WAN lease by pressing the buttons.
You can enter a spoofed MAC address that causes your gateway networking stack to use that MAC
address when communicating instead of the usual WAN MAC address, e.g., if the MAC address is
00:11:e3:df:66:95, this spoofed MAC address could be 00:11:e3:df:66:97 or any desired MAC
address.
Fig. 15 Gateway\Network\WAN
34
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
3. Computers
This page displays the status of the DHCP clients and current system time. You can cancel an IP
address lease by selecting it in the DHCP Client Lease Info list and then clicking the Force Available
button. If you do so, you may have to perform a DHCP Renew on that PC, so that it can obtain a new
lease.
Fig. 16 Gateway\Network\Computers
35
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
4. DDNS - Dynamic DNS service
This page allows to setup for Dynamic DNS server.
Fig 17 Gateway\Network\DDNS
36
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
5. Time server
This page allows configuration and display of the system time obtained from network servers via
Simple Network Time Protocol. The system has to be reset for any changes to take effect.
Fig 18 Gateway\Network\Time
37
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Gateway – Advanced Web Page Group
1. Options
This page allows you to enable/disable some features of the Wireless Voice Gateway.
Fig. 19 Gateway\Advanced\Options
•
WAN Blocking prevents others on the WAN side from being able to ping your gateway. With
WAN Blocking enabled, your gateway will not respond to pings it receives, effectively “hiding”
your gateway.
•
Ipsec PassThrough enables IpSec type packets to pass WAN LAN. IpSec (IP Security) is a
security mechanism used in Virtual Private Networks (VPNs).
•
PPTP PassThrough enables PPTP type packets to pass WAN LAN. PPTP (Point to Point
Tunneling Protocol) is another mechanism sometimes used in VPNs.
•
Remote Config Management makes the configuration web pages in your gateway accessible
from the WAN side. Note that page access is limited to only those who know the gateway access
password. When accessing your gateway from a remote location, your must use HTTP port 8080
and the WAN IP address of the gateway. For example, if the WAN IP address is 157.254.5.7, you
would navigate to http://157.254.5.7:8080 to reach your gateway.
•
Multicast Enable enables multicast traffic to pass WAN LAN. You may need to enable this to
see some types of broadcast streaming and content on the Internet.
•
UPnP Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers,
access the network and connect to other devices as needed. UPnP devices can automatically
38
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
discover the services from other registered UPnP devices on the network.
•
NatSipAlg Enable the gateway implements SIP ALG (Application-level gateway). It is enabled by
default and help in solving NAT related problems in client LAN side.
39
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
2. IP Filtering
This page enables you to enter the IP address ranges of PCs on your LAN that you don’t want to have outbound
access to the WAN. These PCs can still communicate with each other on your LAN, but packets designated to WAN
addresses are blocked by the gateway.
Fig. 20 Gateway\Advanced\IP Filtering
40
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
3. MAC Filtering
This page enables you to enter the MAC address of specific PCs on your LAN that you do not wish to
have outbound access to the WAN. As with IP filtering, these PCs can still communicate with each
other through the gateway, but packets they send to WAN addresses are blocked.
Fig. 21 Gateway\Advanced\MAC Filtering
41
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
4. Port Filtering
This page allows you to enter ranges of destination ports (applications) that you don’t want your LAN
PCs to send packets to. Any packets your LAN PCs send to these destination ports will be blocked.
For example, you could block access to worldwide web browsing (http = port 80) but still allow email
service (SMTP port 25 and POP-3 port 110). To enable port filtering, set Start Port and End Port for
each range, and click Apply. To block only one port, set both Start and End ports with the same value.
Fig. 22 Gateway\Advanced\Port Filtering
42
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
5. Forwarding
For LAN WAN communications, the gateway normally only allows you to originate an IP
connection with a PC on the WAN; it will ignore attempts of the WAN PC to originate a connection
onto your PC. This protects you from malicious attacks from outsiders. However, sometimes you may
wish for anyone outside to be able to originate a connection to a particular PC on your LAN if the
destination port (application) matches one you specify.
This page allows you to specify up to 10 such rules. For example, to specify that outsiders should have
access to an FTP server you have running at 192.168.0.5, create a rule with that address and Start Port
=20 and End Port =21 (FTP port ranges) and Protocol = TCP (FTP runs over TCP and the other
transport protocol, UDP), and click Apply. This will cause inbound packets that match to be forwarded
to that PC rather than blocked. As these connections are not tracked, no entry is made for them in the
Connection Table. The same IP address can be entered multiple times with different ports.
Fig. 23 Gateway\Advanced\Forwarding
43
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
6. Port Triggers
Some Internet activities, such as interactive gaming, require that a PC on the WAN side of your
gateway be able to originate connections during the game with your game playing PC on the LAN side.
You could use the Advanced-Forwarding web page to construct a forwarding rule during the game,
and then remove it afterwards (to restore full protection to your LAN PC) to facilitate this. Port
triggering is an elegant mechanism that does this work for you, each time you play the game.
Fig. 24 Gateway\Advanced\Port Triggers
Port Triggering works as follows. Imagine you want to play a particular game with PCs somewhere on
the Internet. You make one time effort to set up a Port Trigger for that game, by entering into Trigger
Range the range of destination ports your game will be sending to, and entering into Target Range
the range of destination ports the other player (on the WAN side) will be sending to (ports your PC’s
game receives on). Application programs like games publish this information in user manuals. Later,
each time you play the game, the gateway automatically creates the forwarding rule necessary. This
rule is valid until 10 minutes after it sees game activity stop. After 10 minutes, the rule becomes
inactive until the next matched outgoing traffic arrives.
For example, suppose you specify Trigger Range from 6660 to 6670 and Target Range from 113 to
113. An outbound packet arrives at the gateway with your game-playing PC source IP address
192.168.0.10, destination port 666 over TCP/IP. This destination port is within the Trigger destined for
port 113 to your game-playing PC at 192.168.0.10.
You can specify up to 10 port ranges on which to trigger.
44
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
7. DMZ Host
Use this page to designate one PC on your LAN that should be left accessible to all PCs from the
WAN side, for all ports. For example, if you put an HTTP server on this machine, anyone will be able
to access that HTTP server by using your gateway IP address as the destination. A setting of “0”
indicates NO DMZ PC. “Host” is another Internet term for a PC connected to the Internet.
Fig. 25 Gateway\Advanced\DMZ Host
45
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
8. RIP (Routing Information Protocol) Setup
This feature enables the gateway to be used in small business situations where more than one LAN
(local area network) is installed. The RIP protocol provides the gateway a means to “advertise”
available IP routes to these LANs to your cable operator, so packets can be routed properly in this
situation.
Your cable operator will advise you during installation if any setting changes are required here.
Fig. 26 Gateway\Advanced\RIP Setup
46
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Gateway – Firewall Web Page Group
1. Web Content Filtering
These pages allow you to enable, disable, and configure a variety of firewall features associated with
web browsing, which uses the HTTP protocol and transports HTML web pages. On these pages, you
designate the gateway packet types you want to have forwarded or blocked. You can activate settings
by checking them and clicking Apply.
The web-related filtering features you can activate from the Web Content Filter page include Filter
Proxy, Filter Cookies, Filter Java Applets, Filter ActiveX, Filter Popup Windows, and Firewall
Protection.
If you want the gateway to exclude your selected filters to certain computers on your LAN, enter their
MAC addresses in the Trusted Computers area of this page.
Fig. 27 Gateway\Firewall\Web Filter
47
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
2. TOD Filtering
Use this page to set rules that will block specific LAN side PCs from accessing the Internet, but only
at specific days and times. Specify a PC by its hardware MAC address, and then use the tools to
specify blocking time. Finally, click the Apply button to save your settings.
Fig. 28 Gateway\Firewall\TOD Filtering
48
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
3. Local Log and Remote Log
The gateway builds a log of firewall blocking actions that Firewall has taken.Using the Local Log
page lets you specify an email address to which you want the gateway to email this log. You must also
tell the gateway your outgoing (i.e. SMTP) email server’s name, so it can direct the email to it. Enable
Email Alerts has the gateway forward email notices when Firewall protection events occur. Click
E-mail Log to immediately send the email log. Click Clear Log to clear the table of entries for a fresh
start.
The log of these events is also visible on the screen. For each blocking event type that has taken place
since the table was last cleared, the table shows Description, Count, Last Occurrence, Target, and
Source.
Fig. 29 Gateway\Firewall\Local Log
The Remote Log page allows you to specify the IP address where a SysLog server is located and select
different types of firewall events that may occur. Then, each time such an event occurs, notification is
automatically sent to this log server.
Fig. 30 Gateway\Firewall\Remote Log
49
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Gateway – Parental Control Web Page Group
1. Basic
This page allows you to enable, disable, and configure a variety of firewall features associated with
web browsing, which uses the HTTP protocol and transports HTML web pages. On these pages, you
designate the gateway packet types you want to have forwarded or blocked. You can activate settings
by checking them and clicking Apply.
Here are some of your choices on the Parental Control page:
•
Activate Keyword Blocking and specify some keywords in the Keyword List to cause blocking
of web pages on the WAN side with the specified keyword in the content.
•
Activate Domain Blocking and specify some Domain Names (e.g. disney.com) in the Domain
List.
Fig. 31 Gateway\Parental Control\Basic
50
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Gateway – Wireless Web Page Group
The Wireless web pages group enables a variety of settings that can provide secure and reliable
wireless communications for even the most demanding tech-savvy user.
The Wireless Voice Gateway offers a choice of 802.1x, WPA and WPA-PSK authentication of your
PCs to the gateway, 64 and 128 bit WEP encryption of communication between the gateway and your
PCs to guaranty security, and an Access Control List function that enables you to restrict wireless
access to only your specific PCs.
The wireless function will probably work in your home as shipped from the factory, but without the
security features activated. In addition, the factory default wireless channel setting may not provide
optimum changes are recommended from the factory defaults, to secure your wireless communications
and provide optimum performance.
Performance
Because your wireless communication travels through the air, the factory default wireless channel
setting may not provide optimum performance in your home if you or your neighbors have other
interfering 2.4GHz devices such as cordless phones. If your wireless PC is experiencing very sluggish
or dramatically slower communication compared with the speed you achieve on your PC that is wired
to the gateway, try changing the channel number. See the 802.11b/g/n Basic Web Page discussion
below for details.
Authentication
Authentication enables you to restrict your gateway from communicating with any remote wireless
PCs that aren’t yours. The following minimum authentication-related changes to factory defaults are
recommended. See the 802.11b/g Basic and Access Control Web Page discussions below for details.
Network Name (SSID) – Set a unique name you choose
Network Type – Set to Open
Access Control List – Enter your wireless PCs’ MAC addresses
Security
Security secures or scrambles messages traveling through the air between your wireless PCs and the
gateway, so they can’t be observed by others. The following minimum security setting changes to
factory defaults are recommended. See the 802.11b/g Security Web Page discussion below for details.
Data Encryption – Set to WEP (64-bit)
PassPhrase – Use this feature to generate security keys
51
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
1. 802.11b/g/n Radio
To set the basic configuration for the wireless features, click RADIO from the Wireless menu. These
must match the settings you make on your wireless-equipped PC on the LAN side.
Fig. 32 Gateway\Wireless\Radio
•
Interface: The wireless radio in your gateway can be completely de-activated by changing Interface to
Disabled. Click the Apply button to save your settings. Activated by changing interface to enabled.
•
Wireless MAC Address: The MAC address for this wireless device will be displayed in this field
automatically.
•
Output Power:
This setting decides the output power of this device. You may use it to economize on electricity
by selecting lower percentage of power output. Control the range of the AP by adjusting the radio
output power.
•
802.11 Band: It can Support 2.4 GHz and 5 GHz exclusively.
•
802.11n mode: It will help you to Enable or Disable the 11N mode. To enable you need to select Auto, to
disable you need to select Off, and so force the AP to operate in 802.11g mode.
•
Bandwidth: Select wireless channel width 20Mhz is for default value (bandwidth taken by wireless
signals of this access point.)
52
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
•
Sideband for Control Channel (40Mhz only): There are “Lower” and “Upper” can be selected if
Bandwidth 40Mhz is Enabled.
•
Control Channel: There are 13 channels that you can choose. Choose the one that is suitable for this
device.
•
Current Channel: The channel that you choose will be displayed in this field.
•
Restore Wireless defaults: To recover to the default settings, press this button to retrieve the settings and
click Apply.
Setting
Description
Value List or Range
Default
Network Name
(SSID)
Set the Network Name
(also known as SSID) of
this network.
Up to 32-character
string containing
ASCII characters only
THOM-Dxxxxxxx
Network Type
Select Closed to hide the
network from active
scans. Select Open to
reveal the network to
active scans.
Open, Closed
Open
New Channel
Select a particular channel
1-13
on which to operate.
1, 6 or 11
Enable or disable the
wireless interface.
Enabled
Interface
Enabled, Disabled
Table1. Basic Settings Definitions
Your service provider might enforce different default settings, please check with your provider to insure
proper setup
53
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
2. 802.11b/g/n Primary Network
This page allows you to configure the Network Authentication. It provides several different
modes of wireless security. You will have to enter proper information according to the mode you
select.
Fig. 33 Gateway\Primary Network
WPA (Wi-Fi Protected Access)/WPA2
/WPA2:
/WPA2
It must be used in conjunction with an authentication server such as RADIUS to provide centralized
access control and management. It can provide stronger encryption and authentication solution than
54
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
none WPA modes. WPA2 is the second generation of WPA security
WPA-PSK (WPA-Pre-Shared Key) /WPA2-PSK (WPA2-Pre-Shared Key):
It is useful for small places without authentication servers such as the network at home. It allows the
use of manually-entered keys or passwords and is designed to be easily set up for home users.
WEP Encryption:
You can choose 64-bit or 128-bit according to your needs. If you choose Disabled, the Network Keys
will not be shown on this page. If selected, the data is encrypted using the key before being transmitted.
For example, if you set 128-bit in this field, then the receiving station must be set to use the128 Bit
Encryption, and have the same Key value too. Otherwise, it will not be able to decrypt the data.
( Note: You need to connect one end of the Ethernet cable to the Ethernet port on the back of your
computer, and the other end to the ETHERNET port on the Wireless Voice Gateway. )
•
If you select WEP (64-bit or 128-bit), you can adjust the following settings-
•
Shared Key Authentication: Decide whether to set the shared key Optional or Required by
selecting from the drop-down menu.
•
Network Key 1 to 4: The system allows you to enter four sets of the WEP key. For 64-bit WEP
mode, the key length is 5 characters or 10 hexadecimal digits. As for 128-bit WEP mode, the key
length is 13 characters or 26 hexadecimal digits.
•
Current Network Key: Select one set of the network key (from 1 to 4) as the default one.
•
PassPhrase: You can enter ASCII codes into this field. The range is from 8 characters to 64
characters. For ASCII characters, you can key in 63 characters in this field. If you want to key
in 64 characters, only hexadecimal characters can be used.
•
Generate WEP Keys: Click this button to generate the PassPhrase.
Fig. 34 PassPhrase
•
Apply: After proper configuration, click Apply to invoke the settings.
55
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
802.1x Authentication
If you enable the 802.1x authentication function, you will have to offer the following information•
RADIUS Server: RADIUS Server is a protocol for carrying authentication, authorization, and
configuration information between a Network Access Server which desires to authenticate its
links and a shared Authentication Server. Please key in the IP Address for the RADIUS Server.
•
RADIUS Port: Besides the IP address of the RADIUS Server, you have to enter the port number
for the server. Port 1812 is the reserved RADIUS-authentication port described in RFC 2138.
Earlier AP (RADIUS clients) use port 1945. The default value will be shown on this box. You
can keep and use it.
RADIUS Key: A RADIUS Key is like a password, which is used between IAS and the specific
RADIUS client to verify identity. Both IAS and the RADIUS client must be use the same
RADIUS Key for successful communication to occur. Enter the RADIUS Key.
•
Fig. 35 802.1x Authentication
56
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
WPA/WPA2
For the WPA/WPA2 network Authentication, the settings that you can adjust including WPA/WPA2
Encryption, RADIUS Server, RADIUS Port, RADIUS Key, Group Key Rotation Interval, and
WPA/WPA2 Re-auth Interval.
•
WPA/WPA2 Encryption: There are three types that you can choose, TKIP*, AES**,
TKIP+AES.
TKIP takes the original master key only as a starting point and derives its encryption keys
mathematically from this mater key. Then it regularly changes and rotates the encryption
keys so that the same encryption key will never be used twice
** AES provides security between client workstations operating in ad hoc mode. It uses a
mathematical ciphering algorithm that employs variable key sizes of 128, 192 or 256 bits.
•
RADIUS Server/RADIUS Port/RADIUS Key: Please refer to the previous page.
•
Group Key Rotation Interval: Key in the time for the WAP group key rotation interval. The unit
is second. With increasing rekey interval, user bandwidth requirement is reduced.
•
WPA/WPA2 Re-auth Interval: When a wireless client has associated with the Wireless Voice
Gateway for a period of time longer than the setting here, it would be disconnected and the
authentication will be executed again. The default value is 3600, you may modify it.
Fig. 36 WPA/WPA2
57
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
WPA-PSK/ WPA2-PSK
For the WPA-PSK/WPA2-PSK network Authentication, the settings that you can adjust including
WPA/WPA2 Encryption, WPA Pre-Shared Key, and Group key Rotation Interval.
•
WPA Pre-Shared Key: Please type the key to be between 8 and 63 characters, or 64
hexadecimal digits. Only the devices with a matching key that you set here can join this network.
•
WPA/WPA2 Encryption & WPA Group Rekey Interval : Please refer to the WPA/WPA2 part.
Fig. 37 WPA-PSK/WPA2-PSK
58
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Automatic Security Configuration
Fig. 38 Automatic Security Configuration
WiFi Protected Setup (WPS) is an easy and secure way of configuring and connecting your WiFi access point.
In your case, the DWG875/DWG875T is the Access Point (AP), and Your PC (or Wifi Device) is called the
STA. When configuring your Wifi Network via WPS, Messages are exchanged between the STA and AP in
order to configure the Security Settings on both devices.
•
WPS Config: It will help you to Enable or Disable the WPS feature. To enable you need to select WPS,
to disable you need to select Disabled.
Note: After you Enabled the WPS you will get the options as show in Fig.35 and the WPS Config State
box will show its configuration status.
•
Device Name: By using this you can change the factory default to a name of your choice which is up to 32
characters long as like SSID.
•
WPS Setup AP: Here you do not need to change anything, just skip this step.
•
WPS Add Client: There are two methods “Push-Button” and “PIN”. Select the method you want.
But, the default selection will be “PIN”.
59
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
If you select “Push-Button”, then the WPS Add Client option will appear as shown below.
Fig. 39 WPS/Push-Button
And then if you click “Add” button then WPS Setup AP page will appear as shown in Fig.38
Fig. 40 WPS Setup AP/PUSH
And WPS Configure Status will be “In progress”, after establishing the connection the WPS Configure
Status will be “Success!” as shown below. After successful connection the client will get IP address from
AP and then internet will be accessible.
Fig. 41 WPS Setup AP successful/PUSH
60
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
If you select WPS Method to PIN then it will ask for PIN while configuring the WiFi AP by showing a
text box so, you need to enter PIN to establish the connection. You can get the PIN from your connected
Wi-Fi client.
Fig. 42 WPS/PIN
•
PIN: Use this option to set the PIN, enter 4-8 digits PIN of the device you wish to configure. After
entering the pin click “Add” button, then the WPS Setup AP page will appear as shown in Fig.41
Fig. 43 WPS Setup AP/PIN
And WPS Configure Status will be “In progress”, after establishing the connection the WPS Configure
Status will be “Success!” as shown below. After successful connection the client will get IP address from
AP and then internet will be accessible.
61
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Fig. 44 WPS Setup AP successful/PIN
62
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
3. Guest Network
This page allows you to configure a guest network.
You can refer to the details described in previous sections to make the WiFi security settings and guest
LAN settings.
Fig. 45 Gateway\Wireless\Guest Network
63
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
4. Access Control
This page allows you to make access control to the AP or connected clients by offering the MAC
Addresses of the clients.
Fig. 46 Gateway\Wireless\Access Control
Administration Web Page Access : Select Allow to permit access to Administration Web Page from
PC connected over Wifi; or choose Deny to prevent the clients connected over Wifi from access to
Administration Web Page.
MAC Restrict Mode : Click Disabled to welcome all of the clients on the network; select Allow to
permit only the clients on the list to access the cable modem; or choose Deny to prevent the clients on
the list to access this device.
MAC Address : Your Gateway identifies wireless PCs by their WiFi MAC Address. This address
consists of a string of 6 pairs of numbers 0-9 and letters A-F, such as 00 90 4B F0 FF 50. It is usually
printed on the WiFi card of the device (e.g. the PCMCIA card in a laptop). It can also be determined
from a Windows DOS prompt as explained below.
Enter the MAC addresses of the connected clients into the fields, and then click Apply to add them to
the list for access control.
Apply : After proper configuration, click Apply to invoke the settings.
Connected Clients : The information of currently connected clients will be displayed here.
64
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
5. Bridging
The Bridging page provides a location where settings can be adjusted related to the WDS (Wireless
Distribution System) feature.
WDS is a system that enables the interconnection of access points wirelessly. It may also be referred
to as repeater mode because it appears to bridge and accept wireless clients at the same time (unlike
traditional bridging).
The wireless gateway can be placed in a mode that allows the gateway to communicate with other
“extender” wireless access points either exclusively or mixed with communications to local PCs. Use
this page to designate the Remote Bridges the gateway is allowed to communicate with, and to select
the Wireless Bridging mode.
Fig. 47 Gateway\Wireless\Bridging
•
Wireless Bridging:
Choose Disabled to shutdown this function; select Enabled to turn on the function of WDS.
•
Remote Bridges:
Enter the MAC Addresses of the remote Bridges to relay the signals for each other.
•
Apply:
After proper configuration, click Apply to invoke the settings.
65
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
6. 802.11e QoS (WMM) Settings
Wi-Fi Multimedia (WMM) is a component of the IEEE 802.11e wireless LAN standard for quality of
service (QoS). The QoS assigns priority to the selected network traffic and prevents packet collisions and
delays thus improving VoIP calls and watching video over WLANs.
•
Enable WMM:
This field allows you to enable WMM to improve multimedia transmission.
•
Enable WMM No-Acknowledgement:
This field allows you to enable WMM No-Ackonwledgement.
•
Power Save Support:
This field allows you to enable WMM Power-Save-Support.
Fig. 48 Gateway\Wireless\WMM
66
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
VoIP – Basic Web Page Group
1. Basic LAN
This page displays the basic LAN status of this device, including the downstream and upstream status,
device information, and interface parameters. You can select specific interface from the Interface
Name drop-down menu.
Fig. 49 VoIP\Basic\Basic LAN
67
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
2. Hardware Info
The hardware Info is displayed on this page.
Fig. 50 VoIP\Basic\Hardware Info
68
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
3. Event Log
The event logs are displayed on this web page. You can check them whenever you need.
Fig. 51-1 VoIP\Basic\Event log\DOCSIS
69
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
Fig. 51-2 VoIP\Basic\Event log\PacketCable
70
Illustrations contained in this document are for representation only.
Chapter 2: WEB Configuration
4. CM State
This page shows the current state of the cable modem.
Fig. 52 VoIP\Basic\Cm state
71
Illustrations contained in this document are for representation only.
Chapter 3: Networking
Chapter 3: Networking
Communications
Data communication involves the flow of packets of data from one device to another. These
devices include personal computers, Ethernet and USB hubs, cable modems, digital routers
and switches, and highly integrated devices that combine functions, like the Wireless Cable
Gateway.
The gateway integrates the functionality often found in two separate devices into one. It’s
both a cable modem and an intelligent wireless gateway networking device that can provide a
host of networking features, such as NAT and firewall. Figure 2 illustrates this concept, with
the cable modem (CM) functionality on the left, and networking functionality on the right. In
this figure, the numbered arrows represent communication based on source and destination,
as follows:
Type of Communication
1. Communication between the Internet and your PCs
Example: The packets created by your request for a page stored at a web site, and the
contents of that page sent to your PC.
2. Communication between your cable company and the cable modem side
Example: When your cable modem starts up, it must initialize with the cable company,
which requires the cable company to communicate directly with the cable modem itself.
3. Communication between your PCs and the networking side
Fig.53 Communication between your PCs and the network side
Example: The Wireless Cable Gateway offers a number of built-in web pages which you
73
Illustrations contained in this document are for representation only.
Chapter 3: Networking
can use to configure its networking side; when you communicate with the networking
side, your communication is following this path.
Each packet on the Internet addressed to a PC in your home travels from the Internet downstream on the cable company’s system to the WAN side of your Wireless Cable Gateway. There
it enters the Cable Modem section, which inspects the packet, and, based on the results,
proceeds to either forward or block the packet from proceeding on to the Networking section.
Similarly, the Networking section then decides whether to forward or block the packet from
proceeding on to your PC. Communication from your home device to an Internet device works
similarly, but in reverse, with the packet traveling upstream on the cable system.
Cable Modem (CM) Section
The cable modem (or CM) section of your gateway uses DOCSIS Standard cable modem
technology. DOCSIS specifies that TCP/IP over Ethernet style data communication be used
between the WAN interface of your cable modem and your cable company.
A DOCSIS modem, when connected to a Cable System equipped to support such modems,
performs a fully automated initialization process that requires no user intervention. Part of
this initialization configures the cable modem with a CM IP (Cable Modem Internet Protocol)
address, as shown in Figure 3, so the cable company can communicate directly with the CM
itself.
Networking Section
The Networking section of your gateway also uses TCP/IP (Transmission Control Protocol/
Internet Protocol) for the PCs you connected on the LAN side. TCP/IP is a networking protocol
that provides communication across interconnected networks, between computers with
diverse hardware architectures and various operating systems.
TCP/IP requires that each communicating device be configured with one or more TCP/IP
stacks, as illustrated by Figure 4. On a PC, you often use software that came with the PC or its
network interface (if you purchased a network interface card separately) to perform this
configuration. To communicate with the Internet, the stack must also be assigned an IP
(Internet Protocol) address. 192.168.100.1 is an example of an IP address. A TCP/IP stack can
be configured to get this IP address by various means, including a DHCP server, by you
directly entering it, or sometimes by a PC generating one of its own.
Ethernet requires that each TCP/IP stack on the Wireless Cable Gateway also have associated
with it an Ethernet MAC (Media Access Control) address. MAC addresses are permanently
fixed into network devices at the time of their manufacture. 00:90:64:12:B1:91 is an example
of a MAC address.
Data packets enter and exit a device through one of its network interfaces. The gateway offers
Ethernet, USB, and 802.11b/g wireless network interfaces on the LAN side and the DOCSIS
network interface on the WAN side.
When a packet enters a network interface, it is offered to all the TCP/IP stacks associated with
the device side from which it entered. But only one stack can accept it — a stack whose
74
Illustrations contained in this document are for representation only.
Chapter 3: Networking
configured Ethernet address matches the Ethernet destination address inside the packet.
Furthermore, at a packet’s final destination, its destination IP address must also match the IP
address of the stack.
Each packet that enters a device contains source MAC and IP addresses telling where it came
from, and destination MAC and IP addresses telling where it is going to. In addition, the
packet contains all or part of a message destined for some application that is running on the
destination device. IRC used in an Internet instant messaging program, HTTP used by a web
browser, and FTP used by a file transfer program are all examples of applications. Inside the
packet, these applications are designated by their port number. Port 80, the standard HTTP
port, is an example of a port number.
The Networking section of the router performs many elegant functions by recognizing
different packet types based upon their contents, such as source and destination MAC
address, IP address, and ports.
Three Networking Modes
Your gateway can be configured to provide connectivity between your cable company and
your home LAN in any one of three Networking Modes: CM, RG, and CH. This mode setting is
under the control of your cable company, who can select the mode to match the level of home
networking support for which you have subscribed. All units ship from the factory set for the
RG mode, but a configuration file which the cable company sends the cable modem section
during its initialization can change it.
Cable Modem (CM) Mode
Fig. 54 Cable Modem Mode
75
Illustrations contained in this document are for representation only.
Chapter 3: Networking
Fig. 55 Two IP stacks are activated in cable modem mode
CM (Cable Modem) Mode provides basic home networking. In this mode, two IP stacks are
active:
•
IP Stack 1 - for use by the cable company to communicate with the cable modem section
only. This stack receives its IP address from the cable company during CM initialization. It
uses the MAC address printed on the label attached to the Wireless Cable gateway.
•
IP Stack 2 - for use by you, the end user, to communicate with the cable modem and
Networking sections, to access the internal web page diagnostics and con guration. This
stack uses a fixed IP address: 192.168.100.1. It uses a MAC address of MAC label + 1 (the
MAC label is found on the bottom of the unit). E.g., if the MAC address is
00:90:64:12:B1:91, this MAC address would be 00:90:64:12:B1:92.
With CM Mode, your cable company must provide one IP address for the CM section, plus one
for each PC you connect from their pool of available addresses. Your cable company may have
you or your installer manually enter these assigned addresses into your PC, or use a DHCP
Server to communicate them to your PCs, or use a method that involves you entering host
names into your PCs.
Note that in CM Mode, packets passing to the Internet to/from your PCs do not travel through
any of the IP stacks; instead they are directly bridged between the WAN and LAN sides.
76
Illustrations contained in this document are for representation only.
Chapter 3: Networking
Residential Gateway (RG) Mode
Fig. 56 Residential Gateway Mode
Fig. 57 Three IP stacks are activated in Residential mode
RG (Residential Gateway) Mode provides basic home networking plus NAT (Network Address
Translation). In this mode, three IP stacks are active:
•
IP Stack 1 - for use by the cable company to communicate with the Cable Modem section
only. This stack receives its IP address from the cable company during CM initialization. It
uses the MAC address printed on the label attached to the Wireless Cable Gateway.
•
IP Stack 3 - for use by you to remotely (i.e. from somewhere on the WAN side, such as at
your remote workplace) communicate with the Cable Modem and Networking sections, to
remotely access the internal web page diagnostics and configuration. This stack is also
77
Illustrations contained in this document are for representation only.
Chapter 3: Networking
used by your cable company to deliver packets between the Internet and the gateway’s
networking section so they can be routed to/from your PCs. This stack requires an IP
address assigned by the cable company from their pool of available addresses. Your cable
company may have you or your installer manually enter assigned addresses into your
gateway, or use a DHCP Server to communicate them, or use a method that involves you
entering host names. This stack uses a MAC address of MAC label + 2 (the MAC label is
found on the bottom of the unit). E.g., if the MAC address is 00:90:64:12:B1:91, this MAC
address would be 00:90:64:12:B1:93.
•
IP Stack 5 - for use by you to locally (i.e. from somewhere on the LAN side in your home)
communicate with the Cable Modem and Networking sections, to access the internal web
page diagnostics and configuration. This stack is also used by the gateway’s networking
section to route packets between the gateway’s Networking section and your PCs. This
stack uses a fixed IP address: 192.168.0.1. It uses a MAC address of MAC label + 4 (the
MAC label is found on the bottom of the unit). E.g., if the MAC address is
00:90:64:12:B1:91, this MAC address would be 00:90:64:12:B1:95.
With RG Mode, your cable company must provide one IP address for the CM section, plus one
for the Networking section, from their pool of available addresses. With RG Mode, each PC you
connect gets an IP address from a DHCP Server that is part of the Networking section of the
gateway.
78
Illustrations contained in this document are for representation only.
Chapter 4: Additional Information
Chapter 4: Additional Information
Frequently Asked Questions
Q. What if I don’t subscribe to cable TV?
A. If cable TV is available in your area, data and voice service may be made available with or without
cable TV service. Contact your local cable company for complete information on cable services,
including high-speed internet access.
Q. How do I get the system installed?
A. Professional installation from your cable provider is strongly recommended. They will ensure proper
cable connection to the modem and your computer. However, your retailer may have offered a self
installation kit, including the necessary software to communicate with your cable ISP.
Q. My modem is connected to the power sector but does not work
A. Check the ON/OFF button on the rear panel of your modem. It should be set to “1”.
Q. Once my Wireless Voice Gateway is connected, how do I get access to the Internet?
A. Your local cable company provides your internet service*, offering a wide range of services including
email, chat, and news and information services, and a connection to the World Wide Web.
Q. It seems that the wireless network is not working
A. Check the WiFi LED on the front panel. If it is no lighted, press on the WPS button (on the side of the
modem) during 3 seconds and then check again the WiFi LED. If it is lighted, then the WiFi is enabled.
Q. Can I watch TV, surf the Internet, and talk to my friends through the Wireless Voice
Gateway at the same time?
A. Absolutely!
Q. What do you mean by “Broadband?”
A. Simply put, it means you’ll be getting information through a “bigger pipe,” with more bandwidth, than
a standard phone line can offer. A wider, “broader” band means more information, more quickly.
Q. What is DOCSIS and what does it mean?
A. “Data over Cable Service Interface Specifications” is the industry standard that most cable companies
are adopting as they upgrade their systems. Should you ever decide to move, the Wireless Voice Gateway
79
Illustrations contained in this document are for representation only.
Chapter 4: Additional Information
will work with all upgraded cable systems that are DOCSIS-compliant.
Q. What is PacketCable and what does it mean?
A. PacketCable is the industry standard for telephony services that most cable companies are adopting as
they upgrade their systems. Should you ever decide to move, the Wireless Voice Gateway will work with
all upgraded cable systems that are PacketCable compliant.
Q. What is Xpress Technology and what does it mean?
A. It is one of the popular performance-enhancing WiFi technologies, designed to improve wireless
network efficiency and boost throughput. It is more efficient in mixed environments, and it can work with
802.11a/b/g networks. When Xpress is turned on, aggregate throughput (the sum of the individual
throughput speeds of each client on the network) can improve by up to 27% in 802.11g-only networks,
and up to 75% in mixed networks comprised of 802.11g and 802.11b standard equipment. The
technology achieves higher throughput by by re-packaging data, reducing the number of overhead control
packets, so that more useful data can be sent during a given amount of time.
* Monthly subscription fee applies.
** Additional equipment required. Contact your cable company and ISP for any restrictions or additional
fees.
80
Illustrations contained in this document are for representation only.
Chapter 4: Additional Information
General Troubleshooting
You can correct most problems you have with your product by consulting the troubleshooting list that
follows.
I can’t access the internet.
•
Check all of the connections to your Wireless Voice Gateway.
•
Your Ethernet card or USB port may not be working. Check each product’s documentation for more
information.
•
The Network Properties of your operating system may not be installed correctly or the settings may
be incorrect. Check with your ISP or cable company.
All of the lights are flashing in sequence.
•
This means the Wireless Voice Gateway is automatically updating its system software. Please wait
for the lights to stop flashing. The updating process typically lasts less than one minute.
•
Do not remove the power supply or reset the Wireless Voice Gateway during this process.
I can’t get the modem to establish an Ethernet connection.
•
Even new computers don’t always have Ethernet capabilities – be sure to verify that your computer
has a properly installed Ethernet card and the driver software to support it.
•
Check to see that you are using the right type of Ethernet cable.
The modem won’t register a cable connection.
•
If the modem is in Initialization Mode, the INTERNET light will be flashing. Call your Cable
Company if it has not completed this 5-step process within 30 minutes, and note which step it is
getting stuck on.
•
The modem should work with a standard RG-6 coaxial cable, but if you’re using a cable other than
the one your Cable Company recommends, or if the terminal connections are loose, it may not work.
Check with your Cable Company to determine whether you’re using the correct cable.
•
If you subscribe to video service over cable, the cable signal may not be reaching the modem.
Confirm that good quality cable television pictures are available to the coaxial connector you are
using by connecting a television to it. If your cable outlet is “dead”, call your Cable Company.
•
Verify that the Cable Modem service is DOCSIS compliant and PacketCable compliant by calling
your cable provider.
81
Illustrations contained in this document are for representation only.
Chapter 4: Additional Information
I don’t hear a dial tone when I use a telephone.
•
Telephone service is not activated. If the rightmost light on the Wireless Voice Gateway stays on
while others flash, check with your TSP or cable company.
•
If the Wireless Voice Gateway is connected to existing house telephone wiring, make sure that
another telephone service is not connected. The other service can normally be disconnected at the
Network Interface Device located on the outside of the house.
•
If using the second line on a two-line telephone, use a 2-line to 1-line adapter cable.
For more Usage and Troubleshooting Tips use the web site links provided on the CD-ROM:
http://www.Technicolor.net/GlobalEnglish/Deliver/Cable/cable-modems-routers-gateways/Pages/default.aspx
82
Illustrations contained in this document are for representation only.
Chapter 4: Additional Information
Service Information
If you purchased or leased your Wireless Voice Gateway directly from your cable company, then warranty
service for the Digital Cable Modem may be provided through your cable provider or its authorized
representative. For information on 1) Ordering Service, 2) Obtaining Customer Support, or 3) Additional
Service Information, please contact your cable company. If you purchased your Wireless Voice Gateway
from a retailer, see the enclosed warranty card.
83
Illustrations contained in this document are for representation only.
Chapter 4: Additional Information
Glossary
10/100/1000 Mbps – Unshielded, twisted pair cable with an RJ-45 connector, used with Ethernet LAN
(Local Area Network). “10/100/1000” indicates speed (10/100/1000 Mbps), “Base” refers to baseband
technology, and “T” means twisted pair cable.
Authentication - The process of verifying the identity of an entity on a network.
DHCP (Dynamic Host Control Protocol) – A protocol which allows a server to dynamically assign IP
addresses to workstations on the fly.
Ethernet adapters – A plug-in circuit board installed in an expansion slot of a personal computer. The
Ethernet card (sometimes called a Network Interface Card , network adapter or NIC) takes parallel data
from the computer, converts it to serial data, puts it into a packet format, and sends it over the
10/100/1000 Mbps LAN cable.
DOCSIS (Data Over Cable Service Interface Specifications) – A project with the objective of
developing a set of necessary specifications and operations support interface specifications for Cable
Modems and associated equipment.
F Connector – A type of coaxial connector, labeled CABLE IN on the rear of the Wireless Voice
Gateway that connects the modem to the cable system.
HTTP (HyperText Transfer Protocol) – Invisible to the user, HTTP is used by servers and clients to
communicate and display information on a client browser.
Hub – A device used to connect multiple computers to the Wireless Voice Gateway.
IP Address – A unique, 32-bit address assigned to every device in a network. An IP (Internet Protocol)
address has two parts: a network address and a host address. This modem receives a new IP address from
your cable operator via DHCP each time it goes through Initialization Mode.
Key exchange - The swapping of mathematical values between entities on a network in order to allow
encrypted communication between them.
MAC Address – The permanent “identity” for a device programmed into the Media Access Control layer
in the network architecture during the modem’s manufacture.
NID - Network Interface Device, the interconnection between the internal house telephone wiring and a
conventional telephone service provider’s equipment. These wiring connections are normally housed in a
small plastic box located on an outer wall of the house. It is the legal demarcation between the
subscriber’s property and the service provider’s property.
84
Illustrations contained in this document are for representation only.
Chapter 4: Additional Information
PacketCable – A project with the objective of developing a set of necessary telephony specifications and
operations support interface specifications for Wireless Voice Gateways and associated equipment used
over the DOCSIS based cable network.
PSTN (Public Switched Telephone Network) – The worldwide voice telephone network which provides
dial tone, ringing, full-duplex voice band audio and optional services using standard telephones.
Provisioning - The process of enabling the Media Terminal Adapter (MTA) to register and provide
services over the network.
TCP/IP (Transmission Control Protocol/Internet Protocol) – A networking protocol that provides
communication across interconnected networks, between computers with diverse hardware architectures
and various operating systems.
TFTP - Trivial File Transfer Protocol, the system by which the Media Terminal Adapter’s configuration
data file is downloaded.
TSP - Telephony Service Provider, an organization that provides telephone services such as dial tone,
local service, long distance, billing and records, and maintenance.
Universal Serial Bus (USB) – USB is a “plug-and-play” interface between a computer and add-on
devices, such as a Wireless Voice Gateway.
Xpress Technology - One of the popular performance-enhancing WiFi technologies, designed to improve
wireless network efficiency and boost throughput. It is more efficient in mixed environments, and it can
work with 802.11a/b/g networks.
Please do not send any products to the Indianapolis address listed in this manual or on the carton. This
will only add delays in service for your product.
THOMSON
101 West 103rd Street,
Indianapolis, IN 46290, USA
85
Illustrations contained in this document are for representation only.
For more information
THOMSON
101 West 103rd Street,
Indianapolis, IN 46290, USA
http://www.technicolor.com
2006 Thomson Inc.- Trademark(s) ® Registered\ -Marca(s) Registada(s)\
○
Photos and features subject to change without notice.
Illustration of product finish may vary from actual color.
C