User manual | 3180

Manual Index
DEMING
®
INSTALLATION, OPERATION & MAINTENANCE MANUAL
Vertical In-Line Centrifugal Pumps
Series: 3180
Section: 38
ANSI B73.2
IMPORTANT!
A Crane Co. Company
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notification.
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Form No. 119992-Rev. C
CONTENTS
SAFETY FIRST ................................................................................3
A.
GENERAL INFORMATION...............................................................4
Receiving, Storage, Service Centers
B.
INSTALLATION ................................................................................4 - 5
Foundation, Piping, Wiring, Cooling
C.
OPERATION.....................................................................................5 - 6
Priming, Inital Adjustments - Packed Pumps
Inital Adjustments - Pumps with Mechanical Seals
D.
MAINTENANCE ...............................................................................6
Lubrication, Single Seal, Double Seal, Packing Box Care
E.
DISASSEMBLY ................................................................................6 - 8
F.
ASSEMBLY ......................................................................................8 - 9
G.
SPARE PARTS .................................................................................9
CROSS-SECTION & PARTS LIST ...................................................9 - 10
WARRANTY & RETURNED GOODS ..............................................11
Other brand and product names are trademarks or registered trademarks of their respective holders.
Deming® is a registered trademark of Crane Pumps & Systems, Inc.
1993, 11/06
2
Alteration Rights Reserved
SAFETY FIRST!
Please Read This Before Installing Or Operating Pump.
This information is provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help recognize this information,
observe the following symbols:
WARNING ! Do not wear loose clothing that may
become entangled in moving parts.
WARNING ! Keep clear of suction and discharge
openings. DO NOT insert fingers in pump with power
connected.
IMPORTANT! Warns about hazards that can result
in personal injury orIndicates factors concerned with
assembly, installation, operation, or maintenance which
could result in damage to the machine or equipment if
ignored.
Always wear eye protection when working on pumps.
CAUTION! Warns about hazards that can or will cause minor
personal injury or property damage if ignored. Used with symbols
below.
Make sure lifting handles are securely fastened each
time before lifting. DO NOT operate pump without safety
devices in place. Always replace safety devices that
have been removed during service or repair. Secure the
pump in its operating position so it can not tip over, fall
or slide.
WARNING! Warns about hazards that can or will cause serious
personal injury, death, or major property damage if ignored. Used
with symbols below.
Hazardous fluids can
cause fire or explosions, burnes or death
could result.
Biohazard can cause
serious personal injury.
Rotating machinery
Amputation or severe
laceration can result.
Extremely hot - Severe
burnes can occur on contact.
DO NOT exceed manufacturers recommendation for
maximum performance, as this could cause the motor
to overheat.
Hazardous fluids can Hazardous pressure, eruptions or explosions could cause personal
injury or property damage.
WARNING ! To reduce risk of electrical shock, all wiring
and junction connections should be made per the NEC
or CEC and applicable state or province and local
codes. Requirements may vary depending on usage
and location.
Hazardous voltage can
shock, burn or cause death.
Only qualified personnel should install, operate and repair
pump. Any wiring of pumps should be performed by a qualified
electrician.
WARNING! Products returned must be cleaned,
sanitized, or decontaminated as necessary prior to
shipment, to insure that employees will not be exposed
to health hazards in handling said material. All Applicable
Laws And Regulations Shall Apply.
WARNING ! To reduce risk of electrical shock, pumps and
control panels must be properly grounded in accordance
with the National Electric Code (NEC) or the Canadian
Electrical Code (CEC) and all applicable state, province,
local codes and ordinances. Improper grounding voids
warranty.
Bronze/brass and bronze/brass fitted pumps may
contain lead levels higher than considered safe for
potable water systems. Lead is known to cause cancer
and birth defects or other reproductive harm. Various
government agencies have determined that leaded
copper alloys should not be used in potable water
applications. For non-leaded copper alloy materials of
construction, please contact factory.
WARNING! To reduce risk of electrical shock, always
disconnect the pump from the power source before
handling or servicing. Lock out power and tag.
WARNING! Operation against a closed
discharge valve will cause premature bearing
and seal failure on any pump, and on end
suction and self priming pump the heat build
may cause the generation of steam with resulting dangerous
pressures. It is recommended that a high case temperature
switch or pressure relief valve be installed on the pump body.
Crane Pumps & Systems, Inc. is not responsible for
losses, injury, or death resulting from a failure to observe
these safety precautions, misuse or abuse of pumps or
equipment.
CAUTION ! Pumps build up heat and pressure
during operation-allow time for pumps to cool
before handling or servicing.
WARNING ! Do not pump hazardous materials
(flammable, caustic, etc.) unless the pump is specifically
designed and designated to handle them.
3
A - GENERAL INFORMATION
Long Term - Any length of time exceeding six (6) months,
but not more than twenty four (24) months. The units
should be stored in a temperature controlled area, a roofed
over walled enclosure that provides protection from the
elements (rain, snow, wind blown dust, etc..), and whose
temperature can be maintained between +40 deg. F and
+120 deg. F. Pump should be stored in its original shipping
container and before initial start up, rotate impeller by hand
to assure seal and impeller rotate freely.
To The Purchaser:
Congratulations! You are the owner of one of the finest
pumps on the market today. These pumps are products
engineered and manufactured of high quality components.
With years of pump building experience along with a
continuing quality assurance program combine to produce
a pump which will stand up to the toughest applications.
Service Centers:
For the location of the nearest Deming Service Center, check
your Deming representative or Crane Pumps & Systems
Service Department in Piqua, Ohio, telephone
(937) 778-8947 or Crane Pumps & Systems Canada, Inc.,
Bramton, Ontario, (905) 457-6223.
Check local codes and requirements before installation.
Servicing should be performed by knowledgeable pump
service contractors or authorized service stations.
Receiving:
Upon receiving the pump, it should be inspected for
damage or shortages. If damage has occurred, file a claim
immediately with the company that delivered the pump.
If the manual is removed from the crating, do not lose or
misplace.
B- INSTALLATION
Foundation
The In-Line pumps require no special foundation or piping.
They may be installed on any solid support as shown
in Figure 1, or with no under-support at all, if installed
within rigidly supported piping as shown in Figure 2. As
the illustration shown, they are frequently mounted in a
pipeline like a valve.
Storage:
Short Term - Pumps are manufactured for efficient
performance following long inoperative periods in storage.
For best results, pumps can be retained in storage, as
factory assembled, in a dry atmosphere with constant
temperatures for up to six (6) months.
Figure 1
In this pipeline, pump
is installed on a soild
under-support
Figure 2
When pump is installed
in a rigidly supported
pipeline, a soild undersupport is not required
4
Conduit box locations may be varied in increments of 90º.
Simply remove the four cap screws holding the motor to
the adapter, and rotate the motor until the conduit box is in
the desired position.
Piping
It is very important that suction and discharge pipes “line
up” naturally with the pump. DO NOT “pull” pipes into
position with flange bolts or fittings. Both suction and
discharge pipes should be supported independently near
the pump to avoid transmitting pipe strain to the pump
when flange bolts are tightened. Turn the pump shaft
by hand to see that it rotates freely. If the shaft binds,
indicates excessive strain on the casing, correct before
operating the pump.
Cooling
When pumping liquids exceeding 200º F, a water jacketed
packing box is recommended, see Figure 4. Sufficient
cooling water must be provided to reduce the seal or
packing cavity temperature to 180º F, see Figure 5, cooling
chart. All throttling must be done after water has passed
through the water cavity of the jacketed packing box.
If expansion joints are used, they must be of the limiting
bolt type to contain hydraulic forces. The suction pipe must
be kept free of air leaks, this is particularly true when static
suction lift exists or when suction line pressure is below
atmospheric pressure.
When the supply liquid is below the pump, a foot valve and
strainer should be installed in the suction pipe to facilitate
priming and a check valve should be installed next to the
pump in the discharge line to prevent rupture of the casing
from water hammer shock and/or reverse flow in the event
of power failure. In addition, the discharge line should
include a gate valve if priming is necessary. DO NOT
throttle the pump by adjusting a valve on the suction side
of the pump, this will result in pump cavitation.
If a reducer is used at the suction flange, it must be the
eccentric type installed with its flat surface at the top.
Suction piping should be installed so that it rises gradually
toward the pump.
Figure 4
Jacketed Packing Box
Wiring
Connect the power supply in conformance with local
Codes. Line voltage and wire capacity must match ratings
stamped on the motor name plate.
IMPORTANT! - Check rotation by momentarily
starting motor. Rotation must be clockwise
when viewing the pump from the motor end of
the unit, See Figure 3.
Figure 5 - COOLING CHART
Water Jacketed Stuffing Box Temperature (inlet water 72º F)
C - OPERATION
Figure 3
Motor can be rotated in
90º increments
Priming
Make sure packing (for seal) is supplied with proper
lubrication, see “Packing Box” in adjacent column. The
pump casing and suction pipe must be complerely filled
with liquid before operating the pump. This may be
accomplished by one of the following methods:
If the unit is equipped with a mechanical seal, it must be
lubricated to prevent damage to the seal faces.
5
1.
2.
Single Seal - Pumps with single seals are normally
furnished with an external recirculation line. A portion
of the liquid being pumped is recirculated from the
casing through the seal chamber to serve as a lubricant
and coolant. An alternate method is to supply a cool,
compatible lubricating liquid from an outside source to
the seal chamber at a pressure 15 to 25 psi higher than
suction pressure.
If adequate suction head is available, air can be
relieved from the casing and packing box by one of
two means:
a. For packed pumps, remove pipe plug (264) or
recirculation line fitting from discharge flange.
Replace when casing has been completely filled.
b. For pumps with mechanical seals, remove pipe
plug (208) from stuffing box or seal gland if
flexible-mounted. Do not replace the plug until all
air has escaped.
In cases where there is suction lift and system liquid is
not available, install a foot valve in the suction line.
Prime by filling suction piping and casing completely
through the tap in the discharge flange. Provide an air
vent at the high point.
Double Seal - On double seal applications, the seal
chamber must be filled with lubricant or clear, compatible
lubricating liquid under pressure. The liquid may be from
an outside source or may be from the pump discharge
passing through a filter and/or heat exchanger when
necessary. Pressure on the box must be 15 to 25 psi
higher than suction pressure. The liquid must circulate
through the outlet and a restriction must be placed in the
outlet to assure pressure on the seal chamber.
When the pump is fully primed, start the motor and slowly
open the valve in the discharge line.
Inital Adjustments - Packed Pumps
After the pump has been started, packing box glands
should be tightened to prevent excessive loss of liquid.
Packing Box Care - Before installing new rings of
packing, clean the packing box and inspect parts for wear.
If the shaft sleeve is worn, replace it, new packing will not
do an adequate job on a worn sleeve. Die molded packing
rings are preferable. Insert two rings. Twist the rings
sideways when installing, DO NOT pull the rings straight
out over the shaft. Stagger the joints to minimize leakage.
In cases where packed pumps are operating with a
suction lift over 20 feet, the packing should be lubricated
through the stuffing box tap from an external source. See
“Packing Box” .
Packing should not be too tight, as this will result in
burning the packing and scoring of the shaft sleeve. The
best gland adjustment will allow liquid to drip slowly from
the packing box gland. This will permit proper lubrication
of the shaft and dissipate generated heat. The gland must
NEVER be tightened to the point where leakage through
the stuffing box is completely stopped.
Tamp each ring in place and then slip the lantern ring into
the packing box behind them. Add three more rings behind
the lantern ring. Replace the gland and bolts, rotate the
shaft, and tighten gland securely. Be sure the lantern ring
is positioned to receive lubrication through the orifice in
the housing. Tighten nuts securely to seat the packing,
rotate the shaft several turns, and then loosen the nuts to
“finger-tightness” for starting.
Initial Adjustments - Pumps with Mechanical Seals
Mechanical seals are factory-adjusted at the time the
pump is assembled and, normally, need no further
adjustment in the field. The only prerequisite to operating
an In-Line pump equipped with a mechanical seal is to
make certain the seal chamber is filled with a compatible
liquid before starting the pump.
IMPORTANT! - Liquid being pumped should
drip slowly but constantly through the packing
and gland. This will prevent overheating, high
power consumption, and shaft sleeve damage.
NOTE: Numerals shown within parentheses after part
names on this and pages following provide ready
identification of such parts in the cross sectional
drawings.
If packing replacement becomes frequent:
a. Check motor bearing for excessive wear causing
shaft run-out.
b. Check packing for proper grade. Also, check
whether special packing is used, see pump data
card.
c. Check shaft sleeve for excessive wear or scoring
d. Check for crystallization of solution and for
embedded abrasives in the packing. Method of
packing lubrication may not be satisfactory.
e. Check recirculating line, if used, as well as
relevant fittings for partial or full blockage.
MAINTENANCE
D - Lubrication
Motor Bearings - See motor manufacturer’s recommendations
on motor name plate.
Packing Box - Packing must be continuously lubricated.
Packed pump are normally furnished less an external
recirculation line. When operating with suction lift and
clean liquid, recirculation from the pump discharge to
the packing box (or suitable grease) may be used, see
“Initial Adjustments” . When lubrication is supplied from an
outside source, it should be cool, clear water, light lithium
base grease, or a compatible lubricating fluid.
E - DISASSEMBLY
The In-Line Pumps feature “pull-out maintenance”
whereby the rotating assembly can be removed while the
casing remains in the line. To facilitate disassembly, refer
to Figure 6 thru 9 and to assembly drawings on page 10.
6
15. Remove stationary seat (A) and gasket (259) from
gland (251). Remove adapter from motor.
Steps 1 thru 6 that follow apply to all pumps.
1. Remove all cooling or lubrication lines, disconnect
the power.
2. Remove cap screws (212) holding casing (1) to
the adapter (71).
3. Tighten the jack screws (287) uniformly. This will
raise the unit out of the casing and simultaneously
lock the packing box cover (11) to the adapter.
Draw the jack screws up snug, see Figure 6.
Step 13a for Double Seal Pumps ONLY.
13a. Remove rotating portion of seal from the sleeve,
and stationary seats (A) and gasket (259) from the
gland and packing box. Remove adapter from motor.
Figure 7 - Single Seal Clamped Seat
Figure 6
4. Remove the motor and rotating assembly.
5. Remove the impeller screw (26), washer (270),
o-ring (272) and gasket (30), and pull the impeller
(2) from the shaft. Remove the impeller key (32)
and shaft gasket (38). If the wear rings on the
impeller (optional) and in the casing are worn or
scored, they should be replaced.
Steps 6 thru 9 for Packed Pumps ONLY.
6.
7.
8.
9.
Remove the split gland nuts (210), clips (206), and
the gland (17).
Remove the jack screws and slide the packing box
cover off. The shaft sleeve (14) may or may not come
off. If it does, simply remove it from the packing box, if
it clings to the shaft and is not scored, it may remain
there.
Remove the packing (13) and lantern ring (29).
Remove the cap screws (219) holding the motor to
the adapter. Remove the adapter from the motor.
Figure 8 - Single Seat Flexible Mount
Steps 10 and on apply only to pumps with mechanical
seals as shown in Figures 9 to 11. For other seal
constructions, see instructions furnished with pump.
10. Remove nuts (210) on seal gland studs (281).
11. Remove jack screws and, while holding shaft sleeve
in place, slip the stuffing box cover off.
12. With seal assembly on shaft sleeve, remove sleeve
and seal gland (251).
Steps 13 thru 15 for Single Seal Pumps ONLY.
13. Scribe a mark on sleeve at the spring retainer so that
proper axial location will be maintained when the
pump is reassembled.
14. Loosen set screws (K) in spring retainer (E) or seal
collar. Remove seal from sleeve.
Figure 9 - Double Seal
7
6.
Replace the jack screws (28) an draw down snug,
see Figure 8.
7.
Place the shaft gasket (38) over the end of the shaft.
Place the impeller (2) over the end of the shaft with
the keyway over the key. The impeller should be
tapped into position with a babbit or rawhide hammer.
Replace the impeller gasket (30), impeller washer
(270), o-ring (272), and impeller screw (26), and
tighten. Proceed to Step 8.
PARTS IDENTIFICATION LISTING DFOR SEAL TYPES
ILLUSTRATED IN FIGURES 9, 10 AND 11
Item
A
B
C
D
E
F
G
H
Name of part
Item
Name of part
J Shaft Packing
Seat (insert)
Gasket (outboard) K Set Screw
Washer (seal ring) P Throttle Bushing (Optional)
R O-ring
Shaft Packing
S Holding Clips *(Types 9T, 9BT)
Spring Retainer
251 Seal Gland
Spring
259 Gasket (inboard)
Disc
263 Pipe Plug
Snap Ring
Steps 4a thru 6b for Single Seal Pumps ONLY.
(*) Holding clips must be removed after seal is assembled on
shaft; see instructions furnished with seal.
4a. Before installing new or used seals, inspect and clean
all parts, remove all burrs, nicks etc., from shaft
sleeve.
F - ASSEMBLY
4b. Lightly oil the inside of the spring retainer or holder
(E) and the outside of the sleeve. Slide the rotating
portion of the seal over the sleeve.
Steps 1 through 3 apply to packed or sealed pumps.
1.
2.
4c. Line up the spring retainer to the premarked position
(see Step 13 under E - Disassembly). Tighten the set
screws.
If wearing rings need replacement, press the packing
box cover wearing ring (27) into the recess of the
packing box cover (11) making certain that it is
properly seated. The casing wearing ring (7) should
be pressed into the casing (1) until it is flush with the
inside edge of the casing.
5a. Replace the seal gland gaskets (A and 259). Oil the
outer surface of the seal seat (A) and press into the
seal gland (251).
5b. Carefully slide the seal gland and the gland gasket
(259) over the motor shaft.
If impeller (2) was equipped with wearing rings,
press the rear ring (8) onto the shoulder at the rear
of the impeller until it is flush with the rear face. Press
the front ring (8) onto the front shoulder of the impeller
so that it is flush with the front face.
5c. Place the shaft sleeve on the shaft and line up the
keyway in the sleeve with the keyslot in the shaft.
Replace the impeller key (32).
Before proceeding check wear ring tolerances. If
clearances are not as shown in the table below, it is
suggested that the impeller be machined to give the
correct clearance.
6a. If supplied, replace the throttle bushing in the packing
box.
6b. Place the packing box cover over the shaft and seal
the assembly. Replace jack screws (28) and draw
down snug (see Figure 8).
WEARING RING CLEARANCES (DIAMETRICAL)
Sizes
VAAE, VABE, VA10E
VA05E, VA50E, VA60E, VA70E
VA20E, VA30E, VA40E
VA80E
7a. Place the shaft gasket (38) over the end of the shaft.
Place the impeller (2) over the end of the shaft also,
with the keyway over the key. Tap impeller into
position with a babbit or rawhide hammer. Replace
the impeller gasket (30), impeller washer (270), o-ring
(272), and impeller screw (26) and tighten.
.011 - .016”
.013 - .018”
.013 - .018”
.017 - .022”
Galling type metals (316 - 347 - A20 Stainless) .017 - .022” All Size
3.
7b. Pull the seal gland into place, replace the gland
fasteners and tighten securely. Proceed to Step 8.
Reposition the adapter (71) on the motor and replace
the cap screws (219). Slide the slinger (40) onto the
shaft.
4.
Insert the shaft sleeve into the bore of the packing
box with the keyway towards the impeller. Insert
packing (13) and lantern ring (29) as described under
“Packing Box Care” .
5.
Place the entire packing box assembly and shaft
sleeve over the shaft and position the packing box
cover on the adapter. Line up the keyway in the
sleeve with the keyslot in the shaft and replace the
impeller key (32).
Steps 4-1 thru 7-2 for Double Seal Pumps ONLY.
4-1. Before installing new or used seals, inspect and clean
all parts, remove all burrs, nicks, etc, from shaft
sleeve.
4-2. Oil outer surface of seal seats (A). Press one into the
seal gland (251) and one into the packing box cover.
5-1. Slide the seal gland (251) and gland gasket (259)
over the motor shaft.
8
5-2. Place the shaft sleeve on the shaft, lining up the
keyway in the sleeve with the key slot in the shaft.
Replace the impeller key (32).
Item No Name of Parts
6-1. Slide the rotating portion of the seal over the shaft
sleeve.
6-2. Slide the packing box cover over the seal assembly
and sleeve. Replace the jack screws (28) and draw
down snug. See Figure 8.
1
Casing
2
Impeller
*7
Casing Wear Ring
*8
Impeller Wear Rings (Optional)
11
Packing Box Cover
*13
Packing
7-1. Place the shaft gasket (38) over the end of the shaft.
Place the impeller (2) over the end of the shaft also,
with the keyway over the key. Tap impeller into
position with a babbit or rawhide hammer. Replace
the impeller gasket (30), impeller washer (270), o-ring
(272), and impeller screw (26), and tighten.
*14
Shaft Sleeve
7-2. Pull the seal gland into place, replace the gland
fasteners and tighten securely. Proceed to Step 8.
*30
32
Impeller Key
Steps 8 thru 11 for Packed or Sealed Pumps ONLY.
*38
Shaft Gasket
8.
Replace the casing gasket (73)
9.
Relocate the unit in the casing and replace cap
screws (212) holding the adapter and cover the
casing.
17
Split Guard
*26
Impeller Screw
*27
Packing Box Wear Ring
29
Lantern Ring
Impeller Washer Gasket
40
Deflector
71
Adapter
*73
Gasket (Casing)
203
Name Plate
206
Split Gland Clip
208
Pipe Plug
210
Hex Nut
212
Cap Screw
214
Drive Screw
G - SPARE PARTS
216
Pipe Plug
219
Cap Screw
The assembly drawings and Parts List illustrate and
identify parts for 3180 Series pumps having a water
jacketed or air cooled stuffing box. Sealed pumps, except
for having a mechanical seal construction instead of the
packed stuffing box, are similar in design, see Figures 9,
10, and 11 and the table “Parts Identification Listing For
Seal Types’.
228
Motor
239
Stud
249
Hex Nut
264
Pipe Plug
270
Impeller Washer
10. Loosen the jack screws (287) to permit the unit to slip
into the casing. See Figure 8.
11. Tighten the cap screws replaced in Step 9 and snug
up the jack screws to prevent them from working out.
*272
When ordering spare parts, include the following data:
a. The serial number of the pump (on name plate)
b. The part name
c. The Item number
d. The quantity of parts required
If an impeller is ordered, specify the diameter across the
blade tips to be sure there is no further trim than that
shown on factory records. If a motor or motor parts are
ordered, specify the name of the driver manufacturer and
all other data on the driver name plate.
Impeller Screw o-ring
281
Gland Stud
287
Jack screw
297
Pipe Plug
298
Thread Protector
(*) Recommended spare parts.
(**) For water jacketed model only.
9
Figure 10
3180 Series
Vertical In-Line
Centifugal Pump
with Water
Jacketed Stuffing
Box (all sizes)
Figure 11
3180 Series
Vertical In-Line
Centifugal Pump with
Air Cooled Stuffing
Box (all sizes)
10
Limited 24 Month Warranty
Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship
under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained
in accordance with our instructions.This warranty gives you specific legal rights, and there may also be other rights
which vary from state to state. In the event the product is covered by the Federal Consumer Product Warranties Law
(1) the duration of any implied warranties associated with the product by virtue of said law is limited to the same
duration as stated herein, (2) this warranty is a LIMITED WARRANTY, and (3) no claims of any nature whatsoever
shall be made against us, until the ultimate consumer, his successor, or assigns, notifies us in writing of the defect,
and delivers the product and/or defective part(s) freight prepaid to our factory or nearest authorized service station.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply.
THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO ANY
PRODUCT SHALL BE TO REPLACE OR REPAIR AT OUR ELECTION, F.O.B. POINT OF MANUFACTURE OR
AUTHORIZED REPAIR STATION, SUCH PRODUCTS AND/OR PARTS AS PROVEN DEFECTIVE. THERE SHALL BE
NO FURTHER LIABILITY, WHETHER BASED ON WARRANTY, NEGLIGENCE OR OTHERWISE. Unless expressly
stated otherwise, guarantees in the nature of performance specifications furnished in addition to the foregoing material
and workmanship warranties on a product manufactured by us, if any, are subject to laboratory tests corrected for
field performance. Any additional guarantees, in the nature of performance specifications must be in writing and such
writing must be signed by our authorized representative. Due to inaccuracies in field testing if a conflict arises between
the results of field testing conducted by or for user, and laboratory tests corrected for field performance, the latter
shall control. RECOMMENDATIONS FOR SPECIAL APPLICATIONS OR THOSE RESULTING FROM SYSTEMS
ANALYSES AND EVALUATIONS WE CONDUCT WILL BE BASED ON OUR BEST AVAILABLE EXPERIENCE AND
PUBLISHED INDUSTRY INFORMATION. SUCH RECOMMENDATIONS DO NOT CONSTITUTE A WARRANTY OF
SATISFACTORY PERFORMANCE AND NO SUCH WARRANTY IS GIVEN.
This warranty shall not apply when damage is caused by (a) improper installation, (b) improper voltage (c) lightning
(d) excessive sand or other abrasive material (e) scale or corrosion build-up due to excessive chemical content. Any
modification of the original equipment will also void the warranty. We will not be responsible for loss, damage or labor
cost due to interruption of service caused by defective parts. Neither will we accept charges incurred by others without
our prior written approval.
This warranty is void if our inspection reveals the product was used in a manner inconsistent with normal industry practice
and\or our specific recommendations. The purchaser is responsible for communication of all necessary information
regarding the application and use of the product. UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE FOR
ANY OTHER DIRECT OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO TRAVEL EXPENSES,
RENTED EQUIPMENT, OUTSIDE CONTRACTOR FEES, UNAUTHORIZED REPAIR SHOP EXPENSES, LOST
PROFITS, LOST INCOME, LABOR CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES
ARE CAUSED BY ANY DEFECTS IN MATERIAL AND\OR WORKMANSHIP AND\OR DAMAGE OR DELAYS IN
SHIPMENT. THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise,
without our prior written approval.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
83 West Drive, Brampton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
IMPORTANT!
WARRANTY REGISTRATION
Your product is covered by the enclosed Warranty.
To complete the Warranty Registration Form go to:
http://www.cranepumps.com/ProductRegistration/
If you have a claim under the provision of the warranty, contact your local
Crane Pumps & Systems, Inc. Distributor.
RETURNED GOODS
RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”.
CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR.
Products Returned Must Be Cleaned, Sanitized,
Or Decontaminated As Necessary Prior To Shipment,
To Insure That Employees Will Not Be Exposed To Health
Hazards In Handling Said Material. All Applicable Laws
And Regulations Shall Apply.

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project