Advertisement
Advertisement
7A300028 Rev. A
ANDES 3
User Guide
Contents
General Precautions ...................................................................................................... 1
Safety ........................................................................................................................... 1
1 Getting Started ....................................................................................................... 2
1.1 Unpacking the Printer ...................................................................................... 2
1.2 Installing and Charging the Battery Cartridge ..................................................... 3
1.2.1 Installing the Battery ............................................................................. 3
1.2.2 Charging the Battery .............................................................................. 4
1.3 Reading the LED Status ................................................................................... 5
1.4 Attaching Belt Loop System ............................................................................. 6
2.1 Adding Paper or Labels .................................................................................... 7
2.2 Tearing Paper ................................................................................................ 8
3 Using the Printer ..................................................................................................... 9
3.1 Initial Power-Up and Self-Test .......................................................................... 9
3.2 Connecting the Printer ................................................................................... 10
3.2.1 Dip Switches Location .......................................................................... 10
3.2.2 Setting Dip Switches ............................................................................ 11
3.2.3 Dip Switch Functions ............................................................................ 11
3.3 Communications ........................................................................................... 12
3.3.1 Serial Communications Specification ....................................................... 12
3.4 Infrared Communications Mode (IrDA) ............................................................ 13
3.5 Bluetooth/802.11b Communications (Option) ................................................... 13
3.6 Magnetic Stripe Reader (Option) ..................................................................... 13
3.7 Programming Information .............................................................................. 14
3.7.1 ASCII Control Characters ...................................................................... 15
3.7.2 Printer Font Commands ........................................................................ 15
3.7.3 Printer Font Commands – Character Set ................................................. 15 i
3.7.4 Printer Graphic Commands ................................................................... 16
3.7.5 Magnetic Card Reader Control Commands (When MCR is installed) ............. 16
3.7.6 Smart Card Reader Control Commands (when SCR is installed) .................. 17
3.7.7 Graphic Logo and Bar Code Commands................................................... 17
3.7.8 Printer Supervisory and Control Commands ............................................. 17
4.1 Print Head Cleaning Instructions ..................................................................... 19
4.2 Charging the Printer Battery .......................................................................... 19
4.2.1 Important Notes on Charging Batteries ................................................... 20
4.2.2 Important Notes on Replacing Batteries .................................................. 20
4.3 Verifying Battery Charge State ....................................................................... 20
4.4 Battery and Safety Information ...................................................................... 21
4.5 Recycling Batteries ....................................................................................... 21
4.6 Troubleshooting ........................................................................................... 22
4.7 Printer Supplies ............................................................................................ 23
5.1 Printer Specifications .................................................................................... 25
5.2 Supply Specifications .................................................................................... 25
5.3 Regulatory Notes .......................................................................................... 26
5.3.1 FCC Part 15 Class B ............................................................................. 26
5.3.2 Warranty ............................................................................................ 26
5.3.3 Warranty and/or Repair Service ............................................................. 26 ii
General Precautions
Before using this product be sure to read through this manual. After reading please keep the manual in a safe place for future reference.
The information contained herein is subject to change without notice of any type.
Datamax-O’Neil is not responsible for any operational results regardless of missing information, errors or any misprinting in this manual.
Datamax-O’Neil is not responsible for problems created as a result of using options and consumables not approved by them.
This product is designed for servicing at an Authorized Service Center. Other than routine maintenance described in this manual the user should not attempt to repair, service or disassemble this product.
Incorrect operation, handling or improper operating environments may cause damage or otherwise affect the proper operation of this product. Such actions invalidate the product warranty.
Safety
In this manual and on the Printer and accessories we make use of internationally recognized safety symbols as follows:
Caution! Refer to the explanation in this Manual
Caution! Risk of electric shock
Double Insulation or Reinforced Insulation
DC, Direct Current or Voltage
AC + DC, Current or Voltage
1
1 Getting Started
1.1 Unpacking the Printer
The ANDES 3 portable printer is a full featured portable receipt printer designed for varied job environments including field service, field sales, hospitality and restaurants, ticketing and many others where point of service receipts are required. The package contains:
Printer
Battery Cartridge
Universal Adapter (USA,UK, European and Australian plugs) for charging the battery inside the printer
Belt Loop System and
Roll of paper supply (already loaded in the printer).
Both cabled and wireless communication is possible.
Overview
FIGURE 1: PRINTER OVERVIEW
2
1.2 Installing and Charging the Battery Cartridge
Note: One battery cartridge is included with the printer. Similar to a cordless phone battery, the printer’s battery must be charged before using it.
Datamax-O’Neil batteries must be cycled several times to achieve maximum capacity. To cycle a battery fully, charge it and then allow full discharge through normal use in the printer.
1.2.1 Installing the Battery
Note: Refer to Figure 2 below to install the battery pack in the printer.
Unlock the battery door by sliding the battery door locking tab down
Open the battery door
Insert the battery as shown. The battery side with two contact terminals should be facing down to make contact with the two spring probes inside the battery compartment.
Close the battery door.
Lock the battery door by sliding the battery door locking tab up
FIGURE 2: INSTALLING THE BATTERY CARTRIDGE
Note: Ensure the battery is properly seated before closing door. To ensure a full charge do not operate the printer while charging.
3
1.2.2 Charging the Battery
Plug battery charger adapter output cable into the battery charger connector as shown in Figure 3.
FIGURE 3 – BATTERY CHARGER
Plug battery charger adapter into the appropriate AC line voltage socket.
The Yellow/Amber charging LED will illuminate indicating that the battery is being charged
The battery will be fast charged and after about 180 minutes. The LED will turn off
To remove the battery cartridge, open the battery door and tip the battery out of the printer
.
Note: To ensure a full charge do not operate the printer while charging.
Note: The wall mounted charger is a Class II equipment (
)
. Multiple plug configurations comply with most international standards. The wall-mounted charger is not supplied with plugs for use in Korea.
Model
Input Voltage/Current
Input Frequency
Output Voltage/Current ( )
ANDES 3
100-240 VAC/0.4A
47-63 Hz
10VDC/1.32A
Do not use a charger not approved by Datamax-O’Neil for use with the ANDES 3.
Use of an unapproved charger could damage the battery pack or the printer and will void the warranty.
The battery terminals are well recessed inside the printer. Do not allow them to contact conductive material since this may create a short circuit, which could cause injury or start a fire.
When using the wall mounted charger, ensure the socket outlet is close to the printer and easily accessible during the process. Switch the socket off, pull the charger from the socket, or disconnect the plug from the printer in case of problems.
4
1.3 Reading the LED Status
The illustration below points out the location of the LED indicators described in Table 1.
FIGURE 4 – LED INDICATOR LOCATIONS
Note: Refer to the Troubleshooting guide to determine error or fault condition.
Table 1 explains the LED indicator status. Refer to Figure 4 for the locations described for
ON/OFF and FEED pushbutton switches and AC adapter socket
Table 1 - Reading the LED Status
5
1.4 Attaching Belt Loop System
The belt loop system consists of two parts as seen in Figure 5:
A knob located on the back part of the printer just above the battery door
A strap with click on connector
To attach the strap to the knob insert the knob located at the bottom of the printer into the slot of the connector. Pull down until you hear a click. The printer is now secure. The loop is then placed over your belt. Allow the printer to hang down to either the left or right hip.
To release the printer, press in on the two latches on the connector and pull the knob clear of the slot.
Note: Do not force or pull the printer from the connector without pressing in on the two latches
KNOB CONNECTION
FIGURE 5– KNOB CONNECTION AND QUICK CLIP
6
2 Loading Supplies
2.1 Adding Paper or Labels
The printer can print text, bar codes and graphics on thermal receipt paper. See “Supply
Specifications” for the width, thickness requirements and approved vendors. Follow these steps to load printer paper.
Open the paper door by pressing the Paper Door Unlock Button on the top cover as indicated in Figure 6.
FIGURE 6 – OPENING PAPER DOOR
Place the paper supply roll into the paper supply well. Make sure the paper supply unwinds from the bottom as shown in Figure 7.
FIGURE 7 – INSTALLING PAPER ROLL
Position the paper supply between the print head guides.
Make sure some supply (2-3 inches) extends beyond the top of the paper supply well.
7
Close the paper door and press close as shown in Figure 8.
FIGURE 8 – CLOSING PRINTER
2.2 Tearing Paper
The printer’s paper door acts as a tear bar. Pull one edge of the paper against the tear bar as indicated, then tear down and across against the tear bar to tear the paper. See Figure 8 for details.
FIGURE 9 - TEARING PAPER
The tear bar may have sharp edges.
Note: Using the tear bar is the only way to tear the paper.
Note: Pulling up and pulling sideways without using the tear bar can cause a paper jam due to paper misalignment in the print head mechanism.
8
3 Using the Printer
3.1 Initial Power-Up and Self-Test
Once the Battery is charged and the paper is loaded, an initial power up and self-test can be performed:
Press the <On/Off> switch once. This turns printer on. LED #1 illuminates in green, blue or orange depending on the mode of communication.
The printer will stay ON until it is manually tuned
OFF.
If the printer is set for infrared communications
(IrDA) mode the printer will stay on all the time.
Pressing the <On/Off> switch again will turn the printer off.
Press the <On/Off> switch to turn the printer off.
The LED turns off.
To start the self-test, press and hold the <FEED> switch then press the <On/Off> switch
The printer will start printing the self-test message.
Release the <FEED> and <On/Off> switches.
Press the <On/Off> or <FEED> switch to stop the
self-test print.
The first few lines of self-test show the printer firmware version, the current printer settings (for example IrDA or Serial mode) and a list of any optional or special features installed. See Figure
10 for details.
FIGURE 10 –SELF-TEST
9
3.2 Connecting the Printer
The ANDES 3 printer supports Serial RS232 and IrDA compatible infrared communication interfaces. Radio frequency (RF) Bluetooth ™ communication is available as an optional feature as well as 802.11 interfaces.
Serial, IrDA, Bluetooth and 802.11b communication settings can be changed via a DIP switch located on the control card.
Printer drivers for Windows 95/98/NT/2000 and XP are available from Datamax-O’Neil.
PrinterCE print Control utility is available from Datamax-O’Neil for Windows CE devices. Printboy Print Utility from Bachmann Software or PalmPrint Utility, from
StevensCreek, are recommended for Palm Pilot devices
3.2.1 Dip Switches Location
The DIP switch is located inside the battery compartment as illustrated below indicating the location of this switch. To access to the dip switches open the battery door and remove to battery to access to the DIP – SWITCH. Figure 11 shows the DIP
– SWITCH location.
The functions assigned to these switches are shown in Table 2.
FIGURE 11 - DIP SWITCH LOCATION
Note: Ensure battery is properly seated before closing the door
If the Serial interface is selected, the communication Parameters, Baud Rate, Data Bit and Parity must be set.
Note: Optional serial cable is available for Serial RS232 communication
(Part # 5892RJD9).
10
7
8
6
3.2.2 Setting Dip Switches
ON
1 2 3 4 5
6 7 8
FIGURE 12: EXAMPLE: DIP SWITCH #1 SHOWN IN ‘ON’ POSITION
Note: Use care when changing dip switch settings. Carefully use a pointer on the dip switch you are going to change. DO NOT use a screw driver or apply excessive force.
3.2.3 Dip Switch Functions
Note: (Developer’s refer to Programming Manual for more information)
Table 2 – DIP Switch Setting
Dip Switch Function Switch # Switch # Switch # Notes
1 & 2
3 & 4 & 5
Communication Interface
Baud Rate
9600
SW 1
SW 3
ON
SW 2
OFF Baud rate set by Dip switches 3,4 and 5
Baud Rate can be negotiated up to the value
OFF
BT Baud Rate set for 57600 bps.
Dip switches 3,4 and 5 must be set to OFF position
802.11 Baud Rate set for 57600 bps
Dip switches 3,4 and 5 must be set to OFF position
SW 4 SW 5
OFF
ON
ON
OFF
OFF ON Use for fixed IrDA
Parity Bit
Parity Enabled
Parity Disabled
Odd/Even
Even Parity Checker
Odd Parity Checker
Auto Power Save
Power Save Disabled
Power Save Enabled
SW 6
ON
OFF
SW 7
ON
OFF
SW 8
OFF
ON
Does not apply for IrDA
Does not apply for IrDA
Does not apply for IrDA
Does not apply for IrDA
Manual On/Off
Auto Power Down
Note: In order for changes to the dip switch configuration to take effect, the printer power must be reset. This action occurs automatically when the battery is removed to gain access to the dip switches.
11
3.3 Communications
The ANDES 3 Printer is able to support two modes of communication simultaneously –
Either RS232 and IrDA (If Dip switch #1 is ON) or RS232 and 802.11b or Bluetooth ™
(If Dip switch #1 is OFF and Dip Switch #2 is ON).
Dip Switch #2 is used to control the RS232 Port. If the Switch is turned ON the RS232 port is disabled and if it is turned OFF the RS232 Port is enabled. If RS232 interface is not required, disabling the port will save battery power.
Bluetooth or 802.11 RF communications is available if optional daughter boards are installed. The printer can have either Bluetooth or 802.11 enabled but not both of them at the same time.
3.3.1 Serial Communications Specification
The RS232C Interface signals for the ANDES 3 Series printers are terminated on a 6
PIN RJ type data connector located on the side of the printer.
Six connections are provided from the Serial Interface to the host computer. The
Table 3 below lists the Serial Interface signals and pin outs on the RJ connector and the connector pin locations are shown in Figure 13.
A minimum of two connections are required for operation: RXD – pin 3 and Common – pin 1
Note: The communication parameters Baud Rate, Data Bit, and Parity must be set to the same settings as the host device.
FIGURE 13 – RJ DATA CONNECTOR
TABLE 3 – ANDES 3 - Serial RS232C Interface signals
12
3.4 Infrared Communications Mode (IrDA)
Dip Switch #1 must be in the <ON> position.
The printer can be powered up by pressing the power <On/Off> switch
If no IrDA connection is made, the printer will automatically power down to a lower power level to conserve battery life. It will remain in a “sleep” mode until an IrDA connection is made, at which time the printer will “wake” up and print the requested data
Pressing the power switch again will turn the printer <OFF>.
3.5 Bluetooth/802.11b Communications (Option)
Bluetooth operation: Dip Switch #1 must be in the <OFF> position.
Dip Switch # 2 must be in the <ON> position.
802.11b operation: Dip Switch #1 and #2 must be in the <ON> position.
Note: Adjust baud rate settings to match those of the BT or 802.11b module in your computing device
The printer can be powered up by pressing the power <On/Off> switch
Pressing the power <On/Off> switch again will turn the printer <OFF>.
Note: It is necessary for the mobile computing device you are using to discover the printer.
Refer to the instructions provided by the systems integrator.
Note: Systems Integrators: Refer to the Bluetooth manual provided with your mobile computer and the Bluetooth section of the Developer’s Manual/802.11b Application Note available for this printer.
3.6 Magnetic Stripe Reader (Option)
The Magnetic Card Reader is a factory-installed option. This option requires special application software to read and process cards with a magnetic stripe, such as credit cards or driver’s license
Note: Refer to the Figure 14 if your printer is equipped with the optional magnetic stripe reader
Quickly swipe the card through the reader either left to right or right to left. The magnetic stripe must be facing toward the paper supply door as indicated below while it is passed through the reader
Refer to Table 4 for the description of the LED indicator Status.
13
LED Indicator
Green
Red
Table 4 - Magnetic Card LED Indicator
State Status
ON
OFF
ON
Ready/waiting for card to be swiped.
Good swipe - Card data read OR
Card not ready to be swiped.
Error reading card’s data.
FIGURE 14: USING THE MAGNETIC CARD READER
3.7 Programming Information
This section lists the printer control commands strings.
Note: System Developers: Please refer to ANDES 3 developer’s manual for further details.
Other features may be available and are described in the Developer’s manual
14
3.7.1 ASCII Control Characters
Character Hex/Dec
EOT 04/04
CONTROL ACTION
End Of Text
BS
HT
LF
VT
FF
CR
SO
SI
XON
AUXON
XOFF
NORM
AUXOFF
CANCEL
08/08
09/09
0A/10
0B/11
0C/12
0D/13
0E/14
0F/15
11/17
12/18
13/19
14/20
15/21
18/24
Back Space
Horizontal Tab
Line Feed
Vertical Tab
Form Feed
Carriage Return
Shift Out
Shift In
Transmitter On.
Printer on.
Printer receiver is off
Return to default 42 column mode
Printer to Host: printer is off
Cancel and reset printer BUFFER
EXTEND 1C/28
EXTEND OFF 1D/29
Extended print
Extended print off/Normal print
3.7.2 Printer Font Commands
Font Name PITCH Character Size
(WxH)
Command
String
ESC+’k’+’9’
Downloadable
Monospace821BT
NO
Monospace821BT 20CPI NO
Monospace821BT 20CPI ESC+’k’+’7’
Monospace821BT 10 CPI Normal 20x23 ESC+’k’+’6’
NO
NO
Courier
Courier Mode 5
Courier Mode 4
Courier Mode 3
Courier Mode 2
Courier Mode 1
Courier Mode 0
24 CPI normal
21 CPI normal
19 CPI normal
16 CPI normal
12 CPI normal
13 CPI rotated
8x23
9x23
10x23
12x23
16x23
14x16
ESC+’k’+’5’
ESC+’k’+’4’
ESC+’k’+’3’
ESC+’k’+’2’
ESC+’k’+’1’
ESC+’k’+’0’
YES
YES
YES
YES
YES
NO
3.7.3 Printer Font Commands – Character Set
Command String
ESC - ‘F’ – 1
ESC - ‘F’ – 2
ESC - ‘U’ - ‘1’
ESC - ‘U’ - ‘0’
Printer Action
Selects International character set
Selects PC Line Draw character set
Enable emphasized print.
Disable emphasized print.
15
Table 5 shows the International and PC Line Character sets from 32 through 255.
Table 5: International and PC Line Draw Character Set
3.7.4 Printer Graphic Commands
Command String
ESC - ‘a’ – n
ESC - ‘J’ – n
ESC - ‘P’ - ‘#’
ESC - ‘P’ - ‘$’
ESC - ‘V’ - n1 – n2
ESC - ‘v’ - n1 – n2
Printer Action
Select dot line spacing between printed lines.
Graphic Line Feed command
Select Online mode, characters printed as received.
Select Buffer mode, characters are printed on (^ D)
8-bit Graphic command
RLE Compressed Graphic command
3.7.5 Magnetic Card Reader Control Commands (When MCR is installed)
Command String
ESC - ‘M’ - ‘nnm’ – Cr
Printer Action
Select MCR with (nn) auto timeout Where nn=”00” to “99” m=1: Reads track 1 only
ESC – ‘C’ m=2: Reads track 2 only m=3: Reads track 3 only m=4: Reads track 1 & 2 m=5: Reads track 2 & 3 m=6: Reads track 1, 2 & 3
Cancel MCR read process
16
3.7.6 Smart Card Reader Control Commands (when SCR is installed)
Command String
ESC - ‘M’ - ‘nn’ - ‘7’- Cr
ESC - ‘M’ - ‘nn’ - ‘8’- Cr
Printer Action
Select SCR in direct mode with Serial RS232.
(nn) is the auto timeout of the SCR.
Select SCR in PassThru mode with BT/802.11 or IrDA on.
(nn) is the auto timeout of the SCR.
3.7.7 Graphic Logo and Bar Code Commands
Command String
ESC – L – G –n
ESC – G - 0x0FF
ESC – L – g – n
Printer Action
Prepare printer to load image:
Loading Logo Complete:
Print stored logo image:
ESC - 'z' - n1 – n2 – L - [data] Print Bar Code without visible text
ESC - 'Z' - n1 – n2 – L - [data] Print Bar Code with visible text
ESC - ‘Q’ - ‘J’ – n
ESC - ‘Q’ - ‘Q’ – n
Reverse Dot Feed
Set Out of Paper Sensitivity
ESC - ‘Q’ - ‘F’ – m
ESC - ‘Q’ - ‘B’ – m
Set Forward Black Mark Seek
Reverse Black Mark Seek
3.7.8 Printer Supervisory and Control Commands
Command String
^V
Printer Action
Buffer, power timer & battery status
ESC - ‘P’ –‘^’
ESC – ‘M’ - ‘000’ - Cr
ESC - ‘M’ - ‘nn0’ - Cr
ESC – ‘M’ - ‘C’
ESC – ‘P’ – ‘( ‘
ESC – ‘ P’ - ‘)’
ESC – ‘ P’ - ‘+’ or ‘-‘
Print Battery Voltage disable the power down timer sets the power down timer to nn seconds
Reset Auto power down to 20 seconds
Firmware version query
Hardware model query:
Enable or Disable EOT printer response
17
18
4 Printer Maintenance
4.1 Print Head Cleaning Instructions
You may need to clean the print head and platen roller after printing a number of rolls of paper, whenever you load new supplies or when you see voids in the printout.
Do not use sharp objects to clean the print head. This may damage the printer and require service.
Open the paper door by pressing the Paper Door Unlock Button on the top cover as shown in Figure 4 . The paper supply door will pop up.
Remove the paper roll.
Moisten a cotton swab with isopropyl alcohol and clean the print head
Clean the platen roller with a dry cloth or small brush
Note: You can also use another cotton swab moistened with isopropyl alcohol. Turn the platen roller with your finger and run the cotton swab or dry cloth across it. Make sure the platen roller is clean all the way around.
Moisten another cotton swab with isopropyl alcohol. Rub the swab across the black mark sensor to remove any build-up
Moisten another cotton swab and rub the swab across the tear bar to remove any build-up
Note: You may experience dust build-up depending on the environment and the quality of the paper supply you use. If this occurs, use a can of compressed air to blow dust and paper debris out of the printer.
4.2 Charging the Printer Battery
The printer battery is charged using the wall mounted charger provided. Follow these steps to charge the battery pack.
Note: Maker sure the printer and all LED’s are OFF before charging battery.
Plug the charger into an appropriate wall socket; then plug the charger line cord into the adapter jack on the side of the printer (see Figure 1 )
The yellow CHARGE LED will illuminate, to indicate battery is charging.
The Charge LED turns off when battery cartridge is fully charged. It takes about 180 minutes to fast charge the battery cartridge
To insure full charge, printer should not be operated while the battery is charging.
19
4.2.1 Important Notes on Charging Batteries
The model ANDES 3 printers require an adapter output of 10VDC/1.32A.
The battery Fast-charge is initiated each time the power adapter is connected to the printer
The Fast-charge controller checks the battery’s voltage and temperature, before the start of the fast recharge process. If the battery voltage or the temperature is outside of the fast-charge limits, the charger defaults to trickle charge at C/10 or 70 mA rate
Optional external battery chargers are available for Datamax-O’Neil batteries. Refer to
Section 4.7
“Printer Supplies” for detailed information.
4.2.2 Important Notes on Replacing Batteries
Check for the correct Datamax-O’Neil part number for the battery and only use that part for your new battery
Risk of explosion if battery is replaced by an incorrect type
Dispose of used batteries according to instructions in Section 4.5
4.3 Verifying Battery Charge State
We strongly recommend testing your printer before returning it to Datamax-O’Neil. Follow these steps to identify and correct any battery power problem that may be encountered.
These will help to identify that the fault is with the printer and not some other part of your system.
To test the AC adapter:
Use a multi-meter and measure the output voltage. Output should be 10VDC.
Press the <ON/OFF> switch and wait until all LED’s are off.
Insert the AC adapter plug into the printer. If the amber LED goes on, the battery is not fully charged but the charge circuit is functioning.
The AC power portion of the circuit appears ok.
To test the DC power:
Disconnect the AC Adapter once the battery has charged for 5 minutes or so.
Press and hold the <FEED> switch, then press and release the <ON/OFF> switch and then release the <FEED> switch. The printer will print a “self test” receipt
If the self test receipt is printed, the DC power is ok.
To test if the battery is accepting charge:
20
Press <ON/OFF> switch and wait until all LED’s are off
Plug the AC power adapter into the printer. Press <ON>; the green LED is illuminated and after about 20 seconds the LED should go off
If the amber LED is on, this will continue on through this test indicating that the battery is accepting a charge and that the charge circuit is ok. At the end of a 180 minute charge cycle the LED will go off.
4.4 Battery and Safety Information
The printer is powered by a 7.4V Li-Ion battery cartridge.
Charging time in the printer is approximately 3.0 hours.
Take the battery out of printer if storing the printer for long periods of time.
The battery storage temperature is 40°F to 104°F (4°C to 40°C). Do not store a fully charged battery at temperatures greater than 104°F (40°C) for long periods of time – the battery may permanently lose charge capacity.
The recommended temperature for charging is between 68°F (20°C) to 77°F (25°C).
Be sure to use a fully charged battery before long or battery intensive printing sessions. Certain operations (for example, printing receipts with a lot of bar codes and graphics) drain the battery more quickly than others.
Dispose according to your local regulations. Do not throw in trash.
Do not disassemble, short circuit, heat above 80°C, or incinerate: the battery may explode.
4.5 Recycling Batteries
The Rechargeable Battery Recycling Corporation (RBRC) is a non-profit organization created to promote recycling of rechargeable batteries. For more information about how to recycle batteries in your area, visit
www.rbrc.org
.
21
4.6 Troubleshooting
Problem
Does not feed paper or has a paper jam.
Does not print
Light printing
Voids in printing
Red (Error) LED on
Action
Remove any jammed supply
Reload paper supply.
Check or replace the printer’s battery
Make sure the paper supply is loaded correctly, not backwards.
Verify communication between the host device and the printer by disconnecting the communication cable and performing a printer self test.
Check or recharge the battery
Adjust the print contrast through print application.
Clean the print head following the cleaning.
Instruction listed in Section 4.1
.
Check that paper roll is not out and paper door is closed.
Error reading MCR.
After extended printing, print head may be hot; printer will pause before resuming printing.
If the problem is not identified by following the above trouble shooting guide, contact
Datamax-O’Neil Technical Support. Support numbers and Email addresses are listed at
Section 6 of this manual.
Other than routine cleaning and other maintenance described in Section 4, the printer is not intended to be serviced by the user. It must be returned to an
Authorized Service Center. Under no circumstances should the user attempt to take the printer apart.
22
4.7 Printer Supplies
Part Number
79328I1
79328I1-1
79328I1R
79328I1R-1
151133
157261
756998-1
757068
757068-CASE
757150
757160
757352
767400-1
767400-2
767400-4
7A1000014
5892RJD9
Available from Datamax-O’Neil at www.datamax-oneil.com
Download: http://www.fieldsoftware.com/PrinterCE.htm
Download http://www.stevenscreek.com/pilot/dodownl oad.html
Description
ANDES 3 PKG
ANDES 3 PKG with Bluetooth™
ANDES 3 PKG 120 with MCR
ANDES 3 MCR PKG with MCR and Bluetooth™
24V In-Vehicle Charger
Multi-Plug Battery Charger Adapter (US, UK, Euro &
Australian Plug
Spare Belt Loop System
ANDES 3 Thermal Paper Pack (4” / 100’, 5 rolls)
ANDES 3 Thermal Paper (Case of 100 Rolls)
Thermal Print Head Cleaning Pen
Magnetic Card Reader Cleaning Cards (5 per order)
Shoulder Strap with Quick Clip
Battery Charger (2 Bay) Li-Ion 120VAC
Battery Charger (2 Bay) Li-Ion 220VAC
Battery Charger (2 Bay) Li-Ion 240VAC
Li-Ion Battery Cartridge: 7.4VDC– 2200 mAH
Serial Data Cable – RJ to DB9 PC compatible
Windows 95/98/NT/2000/ Drivers
Windows CE print Utility
Palm Pilot print Utility
23
24
5 Specifications
5.1 Printer Specifications
Height:
Width:
2.5 inches (64mm)
6.5 inches (167mm)
Length: 7.5 inches (192mm)
Weight: w/battery & supply 1.8 lbs. (850g)
Shipping weight:
Power:
Operating Temp. Limits:
Storage Temp. Limits:
3.3 lbs. (1.5kg)
7.4 V Li-Ion battery
32F to 122F (0 to 50C)
-4F to 140F (-20C to 60C)
Operating Humidity Limits: 20% to 85% non-condensing
Storage Humidity Limits: 5% to 95% non-condensing
Print Width: 4 inches wide (104mm)
203 dpi (8 dots per mm)
Printing Method:
Print Speed:
Supported Fonts:
(Bitmap)
Thermal Direct
Up to 3.0 inches/sec. @ 7.2v to ph.
Standard (normal and bold)
Large (normal)
Reduced (normal and bold)
Supported Bar Codes:
Large rotated.
Codabar, Code 39, UCC/EAN – 128, UPC/EAN/JAN, Interleaved 2 of
5, Code 128
Flash
768K SRAM --- (256K int. -- 512K ext.)
Charging Time: Approximately 180 minutes
Print Ratio: 25% black maximum/sq. in.
5.2 Supply Specifications
Supplies:
Supply Thickness:
Supply Width:
Supply Length:
Supply Sensing:
Paper roll diameter:
Approved Vendors
Thermal direct receipt paper
2.2 to 3.5 mils (receipt paper)
4.33 inches (110mm)
1 roll of receipt paper is ~100 ft. (30km.)
Black mark (on face of supply)
Outside: 2.0 inches (51 mm)
Inside: 0.40 inches (10 mm)
Kansaki: P300, P310, P350, P354, P390, P530UV, TO281CA, OP200,
TO381N, F180, F380, F550
Jujo: TF-50KS-E2C
Honshu: FH65BV-3
25
5.3 Regulatory Notes
5.3.1 FCC Part 15 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
For Bluetooth equipped printers, please note:
The printer contains an OEM Serial Port Adapter from connectBlue with FCC ID:
PVH070101. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
(2) this device must accept any interference received, including interference that may cause undesired operation.”
5.3.2 Warranty
This printer is warranted by Datamax-O’Neil to be free of defects in parts and workmanship for a period of one year from date of shipment. This warranty does not apply to defects resulting from action of the user such as misuse, improper wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification. Datamax-O’Neil specifically disclaims any implied warranties of merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, special, incidental or consequential damages. Datamax-O’Neil’s total liability is limited to the repair or replacement of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral is expressed or implied.
5.3.3 Warranty and/or Repair Service
A Return Authorization number must be issued before a unit is returned to Datamax-O’Neil for repair. Once a unit has been properly returned to Datamax-O’Neil (Note: The customer is responsible for ensuring proper packing to prevent damage in transit as well as the shipping costs back to Datamax-O’Neil), it will be repaired (estimates are provided first if the repair cost is estimated above $100.00) and returned via UPS ground. The customer may elect a faster mode of transport at their cost.
26
6 Customer Support
Datamax-O'Neil Americas
Orlando, FL USA
Monday - Friday
8:00am - 6:00pm EST
Tel: 407-523-5540
Fax: 407-523-5542 [email protected]
Datamax-O’Neil EMEA
Valence France
Monday - Friday
0830 - 1700 GMT
Tel: + 33 (0) 4 75 75 63 00
Fax: +33 (0) 4 75 82 98 38 [email protected]
Datamax-O'Neil Asia-Pacific
Singapore
Monday - Friday
0830 - 1730
Tel: +65 6505 2250
Fax: +65 6769 8135 [email protected]
COPYRIGHT © 2010, DATAMAX-O’NEIL
27
Advertisement
