Allen-Bradley 1791 16A0/B, 0A16/B, 8AC/B, 8AR/B, 32A0/B, 0A32/B, 16AC/B, 24A8/B, 24AR/B, 16B0/B, 0B16/B, 8BC/B, 8BR/B, 32B0/B, 0B32/B, 16BC/B, 24B8/B, 24BR/B Discrete Block I/O User manual
1791 16A0/B, 1791 0A16/B, 1791 8AC/B, 1791 8AR/B, 1791 32A0/B, 1791 0A32/B, 1791 16AC/B, 1791 24A8/B, 1791 24AR/B, 1791 16B0/B, 1791 0B16/B, 1791 8BC/B, 1791 8BR/B, 1791 32B0/B, 1791 0B32/B, 1791 16BC/B, 1791 24B8/B, 1791 24BR/B are small, self-contained remote I/O devices complete with power supply, programmable controller interface, input/output connections and signal conditioning circuitry. Connect sensors and actuators to the module and use the remote I/O cable to connect the block I/O to your programmable controller.
PDF
Download
Document
Advertisement
Advertisement
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment • FAST SHIPPING AND DELIVERY • TENS OF THOUSANDS OF IN-STOCK ITEMS • EQUIPMENT DEMOS • HUNDREDS OF MANUFACTURERS SUPPORTED • LEASING/MONTHLY RENTALS • ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center WE BUY USED EQUIPMENT Sell your excess, underutilized, and idle used equipment We also offer credit for buy-backs and trade-ins www.artisantg.com/WeBuyEquipment InstraView REMOTE INSPECTION LOOKING FOR MORE INFORMATION? Visit us on the web at www.artisantg.com for more information on price quotations, drivers, technical specifications, manuals, and documentation SM Remotely inspect equipment before purchasing with our interactive website at www.instraview.com Contact us: (888) 88-SOURCE | [email protected] | www.artisantg.com 1791 Discrete I/O AC and DC Block I/O Input and Output Modules User Manual Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Important User Information Because of the variety of uses for the products described in this publication, those responsible for the application and use of this control equipment must satisfy themselves that all necessary steps have been taken to assure that each application and use meets all performance and safety requirements, including any applicable laws, regulations, codes and standards. The illustrations, charts, sample programs and layout examples shown in this guide are intended solely for example. Since there are many variables and requirements associated with any particular installation, Allen-Bradley does not assume responsibility or liability (to include intellectual property liability) for actual use based upon the examples shown in this publication. Allen-Bradley publication SGI–1.1, “Safety Guidelines For The Application, Installation and Maintenance of Solid State Control” (available from your local Allen-Bradley office) describes some important differences between solid-state equipment and electromechanical devices which should be taken into consideration when applying products such as those described in this publication. Reproduction of the contents of this copyrighted publication, in whole or in part, without written permission of Allen–Bradley Company, Inc. is prohibited. Throughout this manual we make notes to alert you to possible injury to people or damage to equipment under specific circumstances. ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage or economic loss. Attention helps you: Identify a hazard. Avoid the hazard. Recognize the consequences. Important: Identifies information that is especially important for successful application and understanding of the product. Important: We recommend you frequently backup your application programs on appropriate storage medium to avoid possible data loss. Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Summary of Changes Summary of Changes Summary of Changes This release of the publication contains updated information on: revised labels changed fuse specifications which modules do or do not support complementary I/O Manual Organization To help you find new and revised information in this release of the publication, we have included change bars as shown to the right of this paragraph. S-1 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Table of Contents Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . S1 Manual Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S1 Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P1 Purpose of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vocabulary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About Block I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P1 P1 P1 P1 P2 Introducing Discrete Block I/O . . . . . . . . . . . . . . . . . . . . . . 11 Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How Block I/O Fits in a PLC System . . . . . . . . . . . . . . . . . . . . . . . 11 11 13 I/O Interface and System Design . . . . . . . . . . . . . . . . . . . . 21 Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 21 25 28 Installing Block I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preinstallation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the Block I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Termination Resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surge Suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote I/O Link Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extended Node Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compatibility of 1771 I/O Products with Extended Node Numbers . . Selecting Remote I/O Link Speed . . . . . . . . . . . . . . . . . . . . . . . . 31 31 33 34 334 334 336 337 338 338 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com ii Table of Contents Configuring Your Block I/O for PLC Family Programmable Controllers . . . . . . . . . . . . . . . . . . . . . 41 Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting the Configuration Switches . . . . . . . . . . . . . . . . . . . . . . . . Using Complementary I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 41 49 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Preface Using This Manual Purpose of Manual This manual shows you how to use your block I/O with an Allen-Bradley programmable controller. It helps you install, program and troubleshoot your module. Audience You must be able to program and operate an Allen-Bradley programmable controller (PLC) to make efficient use of block I/O modules. We assume that you know how to do this in this manual. If you do not, refer to the appropriate PLC programming and operations manual before you attempt to program this module. Vocabulary In this manual, we refer to: the block I/O module as the “block” or the “module” the programmable controller as the “controller” or “processor” Manual Organization This manual is divided into five chapters. The following chart shows each chapter with its corresponding title and brief overview of the topics covered in that chapter. Chapter Title Topics Covered 1 Introducing Block I/O Description of the modules, including general and hardware features 2 I/O Interface and System Design Compatibility, device determination and fusing 3 Installing Block I/O Module power requirements, location, and wiring information 4 Configuring Your Block I/O for PLC Family Programmable Controllers How to set the configuration switches and address the block I/O 5 Troubleshooting How to use the indicators to troubleshoot your block I/O module Specifications Specifications for the block I/O modules Appendix A P-1 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Preface Using This Manual About Block I/O Block I/O consists of small, self-contained remote I/O devices complete with power supply, programmable controller interface, input/output connections and signal conditioning circuitry. Table P.A is a list of block I/O modules covered in this publication. Table P.A Types of Discrete Block I/O Related Publications Catalog Number Voltage Description 179116A0/B 120V ac 16 input ac block I/O module 17910A16/B 120V ac 16 output ac block I/O module 17918AC/B 120V ac 8 input/8 output ac block I/O module 17918AR/B 120V ac 8 input/8 relay output ac block I/O module 179132A0/B 120V ac 32 input, 0 output ac block I/O module 17910A32/B 120V ac 0 input, 32 output ac block I/O module 179116AC/B 120V ac 16 input, 16 output ac block I/O module 179124A8/B 120V ac 24 input, 8 output ac block I/O module 179124AR/B 120V ac 24 input, 8 relay output ac block I/O module 179116B0/B 24V dc 16 input dc block I/O module 17910B16/B 24V dc 16 output dc block I/O module 17918BC/B 24V dc 8 input/8 output dc block I/O module 17918BR/B 24V dc 8 input/8 relay output dc block I/O module 179132B0/B 24V dc 32 input, 0 output dc block I/O module 17910B32/B 24V dc 0 input, 32 output dc block I/O module 179116BC/B 24V dc 16 input, 16 output dc block I/O module 179124B8/B 24V dc 24 input, 8 output dc block I/O module 179124BR/B 24V dc 24 input, 8 relay output dc block I/O module For a list of publications with information on Allen-Bradley products, consult our publication index (SD499). P-2 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 1 Introducing Discrete Block I/O Chapter Objectives In this chapter, you will learn what ac and dc block I/O is, its features, and how it functions. General Description Block I/O modules are small, self-contained remote I/O devices complete with power supply, programmable controller interface, input/output connections and signal conditioning circuitry. Table 1.A Types of Discrete Block I/O Catalog Number Voltage Inputs Outputs Description 179116A0/B 120V ac 16 17910A16/B 120V ac 16 0 input, 16 output 17918AC/B 120V ac 8 8 8 input, 8 output 17918AR/B 120V ac 8 8 8 input, 8 relay output 179132A0/B 120V ac 32 17910A32/B 120V ac 179116AC/B 120V ac 16 input, 0 output 32 input, 0 output 32 0 input, 32 output 16 16 16 input, 16 output 179124A8/B 120V ac 24 8 24 input, 8 output 179124AR/B 120V ac 24 8 24 input, 8 relay output 179116B0/B 24V dc 16 17910B16/B 24V dc 17918BC/B 24V dc 17918BR/B 16 input, 0 output 16 0 input, 16 output 8 8 8 input, 8 output 24V dc 8 8 8 input, 8 relay output 179132B0/B 24V dc 32 32 input, 0 output 17910B32/B 24V dc 32 0 input, 32 output 179116BC/B 24V dc 16 16 16 input, 16 output 179124B8/B 24V dc 24 8 24 input, 8 output 179124BR/B 24V dc 24 8 24 input, 8 relay output 1791IOBX1 24V dc 64 64 64 sinking input, 64 sourcing output 1791IOVX1 24V dc 64 64 64 sourcing input, 64 sinking output 1791IOBW1 24V dc 32 32 32 sinking input, 32 sourcing output 1791IOVW1 24V dc 32 32 32 sourcing input, 32 sinking output 1 Not covered in this manual. Refer to individual user manuals for these products. 1-1 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 1 Introducing Block I/O The blocks are compatible with PLC-2, PLC-3, PLC-5/250 and PLC-5 family programmable controllers, and the SLC 5/02 modular controllers. Refer to the table below for information on using block I/O with various Allen-Bradley programmable controllers. If You are Using: You must use: PLC2 family programmable controller 1771SN subI/O scanner or 1772SD and SD2 remote I/O scanners PLC3 family programmable controller PLC5 family programmable controller Block attaches directlyy to controller PLC5/250 programmable controller SLC programmable controller 1747SN remote I/O scanner Figure 1.1 shows the physical features of the block I/O. Figure 1.1 Major Features of the Block I/O Modules 32Point Block I/O 16Point Block I/O 179132B0 17918AC 120V ac IN/OUT 1 00 01 02 03 04 05 06 07 Left Removable Terminal Strip for Input, Output, Remote I/O and Power Connections OUTPUT COMM 00 01 02 03 04 05 06 07 Left and Right Removable Terminal Strips for Input, Output, Remote I/O and Power Connections IN G+1 00 10 01 11 02 12 03 13 04 14 05 15 06 16 07 17 (G+1) 10 11 12 13 14 15 16 17 00 01 02 03 04 05 06 07 00 01 02 03 04 05 06 07 ALLENBRADLEY IN G 00 10 01 11 02 12 03 13 04 14 05 15 06 16 07 17 STATUS STATUS Equipment Grounding Stud 10 11 12 13 14 15 16 17 COMM 00 01 02 03 04 05 06 07 30 30 G 00 01 02 03 04 05 06 07 Indicators INPUT 24V dc INPUT 1 Equipment Grounding Stud 30 RACK # 1 ALLENBRADLEY Switch assemblies are located behind front cover. Open cover to access. 1-2 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 1 Introducing Block I/O Terminal Strip - Remote I/O link, power and input/output connections are made to the removable terminal strip for easy connection of wiring, and block replacement if necessary. Switch Assembly - Two switch assemblies are provided for setting the I/O rack number, starting I/O group, communication rate, last chassis, and last state. Status Indicators - Indicators display the status of communication and input/output. Use these indicators to help in troubleshooting. How Block I/O Fits in a PLC System Block I/O is a complete I/O interface that includes the functionality of the I/O rack, adapter, power supply, and I/O modules in a single unit. Connect sensors and actuators to the module and use the remote I/O cable to connect the block I/O to your programmable controller. Connect the block I/O to your remote I/O link as you would any other device (Figure 1.2). The block looks like a 1/4 I/O rack to the processor, and uses two words of input image table memory and two words of output image table memory. The block is addressed directly on the remote I/O link. Input and output data is scanned asynchronously and transferred back and forth between the block and the controller input and output image table. Figure 1.2 Block I/O Connection in a PLC System Blocks are daisychained to a programmable controller or a scanner Programmable Controller or Scanner Block I/O each block is 1/4 I/O rack 10828I 1-3 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 2 I/O Interface and System Design Chapter Objectives In this chapter, you will learn what is compatible with block I/O, how to determine what devices to use, and what fuse to use for outputs. Input Compatibility Block I/O inputs convert ac or dc signals from user devices to the appropriate logic level for use within the processor. Typical input devices include: proximity switches limit switches selector switches float switches pushbutton switches AC block output modules are compatible with 1771 series input modules that require greater than 3mA for the off-state current. A 1771 I/O input module that meets these specifications is: cat. no. 1771-ID16 ac isolated input module AC block input modules are compatible with 1771 series output modules if the off-state leakage current of the module is less than the block module minimum off-state current and the on-state voltage minimum of the ac block input is greater than the supply voltage minus the on-state voltage drop across the 1771 output module. Some 1771 I/O modules that meet these specifications are: cat. no. 1771-OAN ac (120V) output module cat. no. 1771-OD16 ac (120V) isolated output module at 120V ac cat. no. 1771-ODD ac (120V) isolated output module at 120V ac cat. no. 1771-ODZ isolated ac output module DC block output modules are compatible with 1771 series input modules that require greater than 0.5mA for the off-state current. Some 1771 I/O input modules that meet these specifications are: cat. no. 1771-IB dc (12–24V) input module cat. no. 1771-IBD dc (10–30V) input module cat. no. 1771-IBN dc (10–30V) input module cat. no. 1771-ICD dc (20–60V) input module cat. no. 1771-IN ac (24V) input module cat. no. 1771-IQ16 dc (24V) input module cat. no. 1771-IH dc (24-48V) input module 2-1 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 2 I/O Interface and System Design DC block input modules are compatible with 1771 series output modules if the off-state leakage current of the module is less than the block module minimum off-state current and the on-state voltage minimum of the dc block input is greater than the supply voltage minus the on-state voltage drop across the 1771 output module. Some 1771 I/O modules that meet these specifications are: 1771-OB dc output driver module 1771-OBD dc (10–60V) output module 1771-OBN dc (10–30V) output module Other Allen-Bradley products that are compatible with block inputs are shown in Table 2.A. Table 2.A Compatibility of Other AllenBradley Products Product AC DC Product AC DC Contactors Bulletin 100 Outputs 100A75 100A45 (pure coil) 100B180 (economized coil) Bulletin 500 NEMA 0-2 NEMA 00 Relays (Bulletin 700) Type F Yes Yes Type PK Yes Yes Type N Yes No Type R Yes No Type P Yes Yes Type RM Yes Yes Type PH Yes Yes Series 4000 Yes Yes Series 6000 Yes Yes Series 5000 Yes Yes Series 7000 Yes Yes Photoswitches Inputs Proximity Switches 871C Yes Yes 871 Yes Yes 871L Yes Yes 871Z Yes Yes 871P Yes N/A 802PR see 1 N/A 871T Yes Yes 871T Yes Yes 1 Refer to individual switch specifications 2-2 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 2 I/O Interface and System Design When selecting devices to use with the block I/O inputs, verify that the on–state voltage and currents of the device fall into the on–state region for the block input. Also verify that the off–state current and voltage fall into the off–state region of the block I/O module (Figure 2.1). Figure 2.1 dc Input Specifications ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ ÉÉÉÉÉÉ ÉÉÉÉÉÉ ÉÉÉÉÉÉ ÉÉÉÉÉÉ Current 11mA On Minimum onstate = 2.5mA Undefined or Transition Region Minimum offstate = 1.5mA Off 0 0 5.0 Off 10 Voltage On 30 Figure 2.2 ac Input Specifications at 60Hz ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ ÉÉÉÉÉÉ ÉÉÉÉÉÉ ÉÉÉÉÉÉ ÉÉÉÉÉÉ Current 12.3mA On Minimum onstate = 5.0mA Undefined or Transition Region Minimum offstate = 2.3mA Off 0 0 Off 35 Voltage 79 132 2-3 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 2 I/O Interface and System Design Example: You want to use an ac 2–wire Bulletin 871C Proximity Switch for an input to a block I/O module. To determine if the switch is compatible with the block, verify the following: Iblock-off > Ileakage-switch Vsupply - Vswitch-on > Vblock-on where: Iblockoff = minimum off-state current of block input Ileakageswitch = maximum off-state leakage current of proximity switch Vsupply = minimum value of supply voltage Vswitchon = maximum on-state voltage drop of proximity switch Vblockon = minimum on-state voltage specification Simplified schematics of ac and dc input circuits are shown in Figure 2.3 and Figure 2.4. Figure 2.3 Simplified Schematic of ac Input Circuit Input Indication LED (logic) System Circuitry Opto Isolation Input Filter 33V Input 27KΩ L1 0.2µF 3.16KΩ 79-132V ac 33Ω 27KΩ L2 Common Figure 2.4 Simplified Schematic of Sinking dc Input Circuit Input Indication LED (logic) 2.8KΩ System Circuitry Input Filter Input Opto Isolation +10-30V dc + 464Ω DAN212K Return Common 2-4 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com 18555 Chapter 2 I/O Interface and System Design Output Compatibility The block I/O may be used to drive a variety of output devices. Typical output devices compatible with the block I/O outputs include: motor starters solenoids indicators When designing a system, ensure that the block I/O output can supply the necessary surge and continuous current for proper operation. Take care to ensure that the surge and continuous current are not exceeded. Damage to the module could result. The block I/O outputs are capable of directly driving the block I/O inputs of the same type. AC Outputs The ac output circuits for block I/O are capable of driving ac loads with a maximum surge current (inrush) of 10A/1200 Watts and a maximum holding current of 300mA/36 Watts at 60oC (600mA/72 Watts at 30oC). The maximum drive characteristics are shown below. Figure 2.5 ac Output Drive Current Surge Current 10A Continuous @ 30oC 600mA Continuous @ 60oC 300mA 0 0 10ms 50ms Time The drive circuit for ac outputs is shown in Figure 2.6. 2-5 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 2 I/O Interface and System Design Figure 2.6 Simplified Schematic of ac Output Circuit Output Indication LED (logic) System Circuitry L1 Common Opto Isolation 10Ω 178Ω 20-132V ac 0.033µF 75Ω Out RL L2 When sizing output loads, check the documentation supplied with the output device for the surge and continuous current needed to operate the device. Refer to Table 2.A to determine which Allen-Bradley products will directly interface to the outputs. Example: The output device is an ac solenoid operated air valve with an inrush current (surge) of 1.995A for 10ms and a holding current (continuous) of 275mA. Figure 2.7 shows that the load of the output device is within the operating specifications of the ac output. Figure 2.7 ac Output Drive Current Load for ac Air Valve Surge Current 10A ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ 2A 1.995A Continuous 300mA 275mA 0 0 10ms Time 50ms 2-6 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 2 I/O Interface and System Design DC Outputs The dc output circuits for block I/O are capable of driving dc loads with a maximum surge current (inrush) of 3A/72 Watts and a maximum holding current of 500mA/12 Watts at 60oC (1A/24 Watts at 30oC). The maximum drive characteristics are shown below (Figure 2.8). Figure 2.8 dc Output Drive Current Surge Current 3A Continuous @ 30oC 1A Continuous @ 60oC 500mA 0 0 50ms Time The drive circuit for dc outputs is shown in Figure 2.9. Figure 2.9 Simplified Schematic of dc Output Circuit Output Indication LED (logic) +10-30V dc 10KΩ System Circuitry Opto Isolation 15V + + 4KΩ Output RL 1N4004 - Return 12247-I When sizing output loads, check the documentation supplied with the output device for the surge and continuous current needed to operate the device. Refer to Table 2.A to determine which Allen-Bradley products will directly interface to the outputs. 2-7 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 2 I/O Interface and System Design Relay Output The relay outputs on block I/O modules are electro-mechanical outputs and do not require specific compatibility with the load device as to current sinking or sourcing. Figure 2.10 Simplified Schematic of Relay Output Circuit Input/Output Indication LED (logic) +5V 100Ω 1kΩ 0.033µF System Circuitry L1 Common 20-132V ac L2 Output RL Fusing 12477-I The 16- and 32-point ac and dc block I/O modules are internally fused to protect the module. No external power fusing is required. Outputs are not fused. Fusing of outputs is recommended. If desired to fuse an output, you must provide external fusing. Table 2.B Recommended Fuses Type of Circuit ac dc Part Number1 Size Rating in Amps Maximum Surge Current2 (repeatable every 2s) SANO SS21.0 0.25 in. x 1.25 in. 1.0A 3.0A for 50ms SANO MQ21.0 5mm x 20mm 1.0A 2.5A for 50ms Littelfuse 322 1.25 0.25 in. x 1.25 in. 1.25A 2.25A for 50ms SANO MQ4800 5mm x 20mm 800mA3 2.0A for 50ms 1 Note: Do not substitute another fuse for those listed. 2 The recommended fuses will withstand surges of the above listed currents for the time specified. 3 Current must be limited to 650mA when using this fuse.. Both ac and dc block I/O modules (except relay output modules) are derated linearly above 30oC up to and including 60oC, as shown in Table 2.C. For modules with relay outputs, refer to Appendix A for output current and surge current ratings. 2-8 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 2 I/O Interface and System Design Table 2.C Output Ratings and Nonfused Surge Currents Catalog Number 17910A16/B 17918AC/B 17910A32/B 179116AC/B 179124A8/B 17910B16/B 17918BC/B 17910B32/B 179116BC/B 179124B8/B Maximum Output Rating at: 60oC 30oC Voltage Mounting 120V ac Vertical 600mA 300mA 120V ac Horizontal 300mA 150mA 120V ac Vertical 600mA 300mA 120V ac Horizontal 300mA 150mA 120V ac Vertical 600mA 300mA 120V ac Horizontal 300mA 150mA 120V ac Vertical 600mA 300mA 120V ac Horizontal 300mA 150mA 120V ac Vertical 600mA 300mA 120V ac Horizontal 300mA 150mA 24V dc Vertical 1A 500mA 24V dc Horizontal 500mA 250mA 24V dc Vertical 1A 500mA 24V dc Horizontal 500mA 250mA 24V dc Vertical 1A 500mA 24V dc Horizontal 500mA 250mA 24V dc Vertical 1A 500mA 24V dc Horizontal 500mA 250mA 24V dc Vertical 1A 500mA 24V dc Horizontal 500mA 250mA Maximum Surge Current 10A for 50ms (repeatable every 2s) 3A for 50ms (repeatable every 2s) 2-9 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Chapter Objectives In this chapter, you will learn how to mount the block, connect the input and output wiring to the block, add surge suppression (if required), connect remote I/O wiring, terminate the remote I/O link, and select remote I/O link speed. Preinstallation Considerations Before installation, you must determine the: scanner/processor to use number of blocks on your network throughput requirements total distance of the installation transmission rate desired external fuses required (if any) Acceptable combinations are shown in Table 3.A. Table 3.A Acceptable Combinations of Processor and Block I/O When using and Maximum Capacity 1771SN 16 blocks with 150 ohm terminator 1772SD 1772SD2 1772SD, 16 blocks/channel, 28 blocks/scanner with 150 ohm terminator Any PLC3 scanner module 16 blocks/channel, 64 blocks/scanner with 150 ohm terminator. 128 blocks with 2 scanners and 150 ohm terminator. PLC2 family PLC 3 family f il PLC3 1775S5, or SR5 module PLC5VME (6008LTV)2 PLC5 family PLC5/11 PLC5/151 Baud Rate Used Maximum Network Distance 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 57.6K 10,000 cablefeet 32 blocks/channel, 64 blocks/scanner with 82 ohm terminator. 128 blocks with 2 scanners, 82 ohm terminator and extended node addressing. 115.2K 5,000 cablefeet 230.4K 2,000 cablefeet 4 blocks with 150 ohm terminator 57.6K 10,000 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 230.4K 2,500 cablefeet 57.6K 10,000 cablefeet 4 blocks with 150 ohm terminator 12 blocks with 150 ohm terminator 3-1 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O When using and PLC5/20 PLC5/25 Maximum Capacity 12 blocks with 82 ohm or 150 ohm terminator 16 blocks with 150 ohm terminator, 28 blocks with 82 ohm terminator and extended node addressing 16 blocks/channel, 28 blocks per processor with 150 ohm terminator PLC5/30 28 blocks/channel, blocks/channel 28 blocks per processor with 82 ohm terminator and extended node addressing 16 blocks/channel, 60 blocks per processor with 150 ohm terminator PLC5/40 32 blocks/channel, blocks/channel 60 blocks per processor with 82 ohm terminator and extended node addressing PLC5 family (continued) 16 blocks/channel, 32 blocks per processor with 150 ohm terminator PLC5/40L 32 blocks/channel, blocks/channel 60 blocks per processor with 82 ohm terminator and extended node addressing 16 blocks/channel, 64 blocks per processor with 150 ohm terminator PLC5/60 32 blocks/channel, blocks/channel 92 blocks per processor with 82 ohm terminator and extended node addressing 16 blocks/channel, 32 blocks per processor with 150 ohm terminator PLC5/60L 32 blocks/channel, blocks/channel 64 blocks per processor with 82 ohm terminator and extended node addressing Baud Rate Used Maximum Network Distance 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 230.4K 2,500 cablefeet 57.6K 10,000 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 230.4K 2,500 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 230.4K 2,500 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 230.4K 2,500 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 230.4K 2,500 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 230.4K 2,500 cablefeet 3-2 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O When using and 16 blocks/channel, 32 blocks/scanner, (128 blocks with 4 scanners) with 150 ohm terminator and extended node addressing PLC5/250 requires a 5150RS remote scanner PLC 5 family f il (continued) ( ti d) PLC5 S C / or SLC5/03 S C / SLC5/02 Controllers Baud Rate Used Maximum Capacity 32 blocks/channel, 32 blocks/scanner, (128 blocks with 4 scanners) with 82 ohm terminator and extended node addressing S Remote I/O /O Scanner S 1747SN Module 16 blocks with 150 ohm terminator 16 blocks with 82 ohm terminator Maximum Network Distance 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 230.4K 2,500 cablefeet 57.6K 10,000 cablefeet 115.2K 5,000 cablefeet 230.4K 2,500 cablefeet 1 PLC5/15 series A and PLC5/15 series B prior to revision H (B/H) can only address 3 blocks. 2 PLC5/25 revisions prior to A/D can only address 7 blocks. Installing the Block I/O Figure 3.1 shows the mounting dimensions for the block I/O module. Mount the blocks vertically with a minimum of 2” between blocks. This air gap is necessary to maintain proper cooling air flow through the block. Figure 3.1 Mounting Dimensions for the Block I/O Modules 2.710 (68.8) 1.71 (43.4) 0.5 (12.7) 4.35 (110.5) 3.35 (85.1) 0.5 (12.7) 17918AC 1 Block 2.0 (50.8) air gap on all 4 sides. Operating temperature in air gap below module must not exceed 60oC (140oF). Equipment Grounding Stud 00 01 02 03 04 05 06 07 6.60 (167.6) 179124B8 30 24V dc IN/OUT 1 00 01 02 03 04 05 06 07 INPUT 6.95 (176.5) Dimensions Inches (Millimeters) 120V ac IN/OUT IN G OUTPUT 00 01 02 03 04 05 06 07 10 11 12 13 14 15 16 17 00 01 02 03 04 05 06 07 6.95 6.60 (176.5) (167.6) COMM STATUS 00 01 02 03 04 05 06 07 IN (G+1) ALLENBRADLEY IN G+1 00 01 02 03 04 05 06 07 00 01 02 03 04 05 06 07 16point Block I/O Modules 1 RACK # ALLENBRADLEY CAUTION: When tightening grounding stud nut, do not exceed 15 inlbs. 6.95H x 2.710W x 3.85D (176.5H x 68.8W x 98D) OUT G 00 01 02 03 04 05 06 07 OUT G 00 01 02 03 04 05 06 07 30 30 IN G 00 10 01 11 02 12 03 13 04 14 05 15 06 16 07 17 6.95H x 4.35W x 3.85D (176.5H x 110.5W x 98D) 2 Mounting Holes for 1/4inch screws 32point Block I/O Modules 3-3 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.2 Mounting on a DIN Rail 1. Hook top of slot over DIN rail. 2. While pressing block against rail, pull down on locking lever. 3. When block is flush against rail, push up on locking lever(s) to secure block to rail. DIN Rail AB Pt. No. 199DR1 462773 EN 50022 (35 x 7.5mm) Locking Lever Locking levers 32point Block I/O Module Connecting Wiring 16point Block I/O Module 12382I Make wiring connections to the removable terminal block which plugs into the front of the block. ATTENTION: The terminal blocks are not keyed to prevent incorrect insertion. If you remove a terminal block, make certain that each terminal block is inserted with the lower row of screws on the outside of the block (positioned toward the outside of the module). Figure 3.3 Removing the Terminal Block To remove terminal strip, unscrew the 2 captive screws and pull terminal strip out. Repeat for second terminal strip on 32point modules. 32point Block I/O Module 16point Block I/O Module 3-4 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com 12383I Chapter 3 Installing Block I/O Figure 3.4 Terminal Block Pin Numbering 32point Block I/O Module 16point Block I/O Module Refer to the table below for the Figure and page number of the wiring for each block I/O module. Catalog Number Wiring Connections Catalog Number Wiring Connections Catalog Number Wiring Connections 179116A0 Figure 3.5, page 36 179116AC Figure 3.11, page 314 17918BR Figure 3.17, page 323 17910A16 Figure 3.6, page 37 179124A8 Figure 3.12, page 316 179132B0 Figure 3.18, page 324 17918AC Figure 3.7, page 38 179124AR Figure 3.13, page 318 17910B32 Figure 3.19, page 326 17918AR Figure 3.8, page 39 179116B0 Figure 3.14, page 320 179116BC Figure 3.20, page 328 179132A0 Figure 3.9, page 310 17910B16 Figure 3.15, page 321 179124B8 Figure 3.21, page 330 17910A32 Figure 3.10, page 312 17918BC Figure 3.16, page 322 179124BR Figure 3.22, page 332 3-5 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.5 Input Connections for the 179116A0 Series B 1 PLC RIO 1 2 GND NOT USED BLU CLR COM 1 COM 1 COM 1 in 00 L2/N in 01 in 02 in 03 L1 in 04 in 05 in 06 30 in 07 30 L1 1 L2/N SLC L1 1 2 N NOT USED RIO NOT USED GND BLU SHD CLR COM 2 COM 2 COM 1 COM 1 COM 2 COM 1 in 10 L2/N in 11 in 12 in 00 L2/N in 01 in 02 in 13 L1 in 14 in 15 in 03 in 04 L1 in 05 in 16 in 06 29 in 17 30 in 07 30 L1 L2/N L1 N NOT USED SHD COM 2 COM 2 COM 2 in 08 L2/N in 09 in 10 in 11 L1 in 12 in 13 in 14 29 in 15 NOTE: Com 1 connections are internally connected together. Com 2 connections are internally connected together. Connections Power Connections Remote I/O Connections 179116A0 Series B Designation Description Terminal L1 ac hot 1 N ac neutral 3 GND Chassis ground 21 BLU Blue wire RIO 6 CLR Clear wire RIO 8 SHD Shield RIO 7 I/O Connections Input Input in 00 thru in 07 Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 COM 1 L2/N Input Common 10, 12, 142 COM 2 L2/N Input Common 9, 11, 133 PLC: in 10 thru in 17 SLC: in 08 thru in 15 PLC: Input 10 thru Input 17 SLC: Input 08 thru Input 15 15, 17, 19, 21, 23, 25, 27, 29 Not used For internal test only; not for customer use. 4, 5 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 10, 12 and 14 are internally connected. 3 Terminals 9, 11 and 13 are internally connected. 3-6 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.6 Output Wiring Connections for the 17910A16 Series B 1 PLC 1 2GND GND NOT NOT USED USED RIO L2/N L1L1 L2/N L1 SLC L1 2 GND NN NOT NOT USED USED L1-2 COM 2 L1-2 COM 2 L2/N BLU L2/N COM L1-1 1 L1-2 COM L1-1 2 COM 1 out 10 L1 SHD L1-2 L1-1 L1-2 L1-1 L2/N out 08 out 00 out 09 out 01 out 10 out 02 out 11 out 03 out 12 out 04 out 13 out 05 out 14 out 06 29 out 15 30 out 07 30 L1 L1-2 L1-1 out 00 00 out 08 out out 11 out 01 01 out 09 out out 12 out 02 out 10 out 13 out 03 out 11 out 03 out 14 out 04 out 12 out 04 out 15 out 13 out out 05 05 out 16 out 06 out 14 out 06 29 out 17 30 15 out 07 L2/N L1 NOT USED CLR L1 L1 1 N NOT USED RIO BLU BLU SHD SHD CLR CLR COM L1-1 1 1 30 NOTE: L11 connections must be externally connected together to accommodate total amperage. L12 connections must be externally connected together to accommodate total amperage. Output fusing is recommended. Refer to Table 2.B on page 28. Connections Power Connections Remote I/O Connections 17910A16 Series B Designation Description Terminal L1 ac hot 1 N ac neutral 3 GND Chassis ground 21 BLU Blue wire RIO 6 CLR Clear wire RIO 8 SHD Shield RIO 7 I/O Connections Output Output out 00 thru out 07 Output 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 L1-1 L1 output supply 10, 12, 142 L1-2 L1 output supply 9, 11, 133 PLC: out 10 thru out 17 SLC: out 08 thru out 15 PLC: Output 10 thru 17 SLC: Output 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 Not used For internal test only; not for customer use. 4, 5 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 10, 12 and 14 must be externally connected by customer. 3 Terminals 9, 11 and 13 must be externally connected by customer. 3-7 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.7 Input/Output Wiring Connections for the 17918AC Series B 1 PLC and SLC 1 2 GND NOT USED RIO BLU CLR COM in COM in COM in in 00 L2/N in 01 in 02 in 03 L1 L1 in 04 in 05 in 06 30 L1 L2/N N NOT USED SHD L1 out L1 out L1 out L1 L2/N out 00 out 01 out 02 out 03 out 04 out 05 out 06 29 out 07 in 07 30 NOTE: COM in connections are internally connected together. L1 out connections must be externally connected together to accommodate total amperage. Output fusing is recommended. Refer to Table 2.B on page 28. Connections Power Connections Remote I/O Connections 12390-I 17918AC Series B Designation Description Terminal L1 ac hot 1 N ac neutral 3 GND Chassis ground 21 BLU Blue wire RIO 6 CLR Clear wire RIO 8 SHD Shield RIO 7 I/O Connections Input Output in 00 thru in 07 Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 COM in L2/N input common 10, 12, 142 L1 out L1 output supply 9, 11, 133 out 00 thru out 07 Output 00 thru 07 15, 17, 19, 21, 23, 25, 27, 29 Not used For internal test only; not for customer use. 4, 5 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 10, 12 and 14 are internally connected. 3 Terminals 9, 11 and 13 must be externally connected by customer. 3-8 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.8 Input/Output Wiring Connections for the 17918AR Series B 1 PLC and SLC 2 1 GND NOT USED RIO BLU N NOT USED SHD CLR Vac/dc COM in COM in COM in in 00 L2/N in 01 in 02 in 03 L1 in 04 in 05 in 06 30 in 07 30 L2/N L1 L1 L1/+ out Vac/dc out Vac/dc out L2/N/ac/dc out 00 out 01 out 02 out 03 out 04 out 05 out 06 29 out 07 NOTE: COM in connections are internally connected together. Vac/dc out connections must be externally connected together to accommodate total amperage. Output fusing is recommended. Size fuse according to output load and surge current requirements. Connections Power Connections Remote I/O Connections 12387-I 1791-8AR Series B Designation Description Terminal No. L1 ac hot 1 N ac neutral 3 GND Chassis ground 21 BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 SHD Shield - RIO 7 I/O Connections Input Output in 00 thru in 07 Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 COM in L2/N input common 10, 12, 142 Vac/dc out ac or dc output supply 9, 11, 133 out 00 thru out 07 Output 00 thru 07 15, 17, 19, 21, 23, 25, 27, 29 Not used For internal test only; not for customer use. 4, 5 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 10, 12 and 14 are internally connected. 3 Terminals 9, 11 and 13 must be externally connected by customer. 3-9 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.9 Input Wiring Connections for the 179132A0 Series B PLC 1 1 2 L1 GND NOT USED NOT USED L2/N in 10 in 00 L1 L1 in 06 in 17 1 SLC 1 1 L1 GND BLU CLR COM 1 COM 1 COM 1 in 13 in 05 in 10 in 02 in 11 in 12 in 09 in 01 in 10 in 04 in 07 L2/N L1 in 11 in 03 in 15 30 in 06 1 in 07 L1 in 13 in 05 in 14 29 in 12 in 04 L1 L2/N in 08 in 00 in 09 in 03 30 in 17 4 COM 4 COM 4 COM 3 COM 3 COM 3 L2/N in 08 in 01 in 06 in 07 30 NO 29 NOT CONN USED NO CONN NOT USED NOT USED NO CONN NO CONN NO CONN COM SHD COM 2 COM 2 COM 2 in 02 L1 in 16 2 30 L2/N NOT USED in 00 L2/N L1 N NOT USED RIO L1 in 15 1 30 2 in 14 in 05 29 in 07 in 13 in 04 in 16 30 in 12 in 03 in 15 in 05 in 11 in 02 in 14 in 04 L2/N in 10 in 01 in 13 in 03 COM 4 COM 4 COM 4 in 00 in 12 in 02 NO CONN COM 3 COM 3 COM 3 in 11 in 01 NOT USED NO CONN L2/N NO CONN NO CONN NO CONN COM 2 COM 2 COM 2 COM 1 COM 1 COM 1 in 06 29 SHD CLR L1 30 NOT USED BLU L2/N 30 L2/N N NOT USED RIO L1 in 14 2 in 15 1 NOTE: COM 1 connections are internally connected together. COM 2 connections are internally connected together. COM 3 connections are internally connected together. COM 4 connections are internally connected together. 3-10 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Connections Power Connections Remote I/O Connections 1791-32A0 Series B Connector/Terminal Designation Description Left Conn. L1 ac hot 1 N ac neutral 3 GND Chassis ground 21 BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 SHD Shield - RIO 7 Right Conn. I/O Connections Input (G)6 Input (G+1)7 in 00 thru in 07 Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 COM 1 L2/N Input Common 10, 12, 142 COM 2 L2/N Input Common 9, 11, 133 PLC: in 10 thru in 17 SLC: in 08 thru in 15 PLC: Input 10 thru 17 SLC: Input 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 in 00 thru in 07 Input 00 thru 07 15, 13, 11, 9, 7, 5, 3, 1 COM 3 L2/N Input Common 17, 19, 214 COM 4 L2/N Input Common 18, 20, 225 PLC: in 10 thru in 17 SLC: in 08 thru in 15 PLC: Input 10 thru 17 SLC: Input 08 thru 15 16, 14, 12, 10, 8, 6, 4, 2 Not used For internal test only; not for customer use. No Conn No internal connection; customer can use. 4, 5 29, 27, 26 30, 28, 25, 24, 23 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Left connector terminals 10, 12 and 14 are internally connected together. 3 Left connector terminals 9, 11 and 13 are internally connected together 4 Right connector terminals 21, 19 and 17 are internally connected together 5 Right connector terminals 22, 20 and 18 are internally connected together 6 IN (G) = input module group (1 word). 7 IN (G+1) = input module group plus 1 word 3-11 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.10 Output Wiring Connections for the 17910A32 Series B PLC 1 1 2 GND RIO L2/N CLR L1 out 00 out 02 out 03 out 04 out 05 out 06 30 out 07 30 29 NOT USED L1-2 NOT USED NO CONN L1 L2/N L1-2 NO CONN NO CONN L2/N L1 L1-4 L1-3 L1-2 L1-3 out 00 out 11 out 01 out 12 out 02 out 13 out 03 out 14 out 04 out 15 out 05 out 16 out 06 29 out 17 1 out 07 L1 L2/N L1 L2/N L1-4 L1-3 out 10 NO CONN NO CONN NOT USED SHD L1-1 out 01 30 L2/N NOT USED L1-1 L1-1 L1 N NOT USED BLU L1 L1-4 out 10 out 11 out 12 out 13 out 14 out 15 out 16 2 out 17 1 30 SLC 1 1 2 GND NOT USED BLU RIO L2/N CLR L1 L1 L1-1 L1-1 L1-1 out 00 out 01 out 02 out 03 out 04 out 05 out 06 30 out 07 30 L1 30 L2/N 30 29 NOT USED N L1-2 L1 L2/N out 08 out 10 out 11 out 12 out 13 out 14 29 out 15 NO CONN NO CONN L2/N L1 L1-4 L1-3 L1-4 L1-3 L1-2 out 09 NOT USED NO CONN SHD L1-2 NO CONN NOT USED NOT USED L1-3 out 00 out 01 out 02 out 03 out 04 out 05 out 06 1 out 07 NO CONN L1-4 out 08 out 09 out 10 out 11 out 12 out 13 out 14 2 out 15 1 NOTE: L1-1 connections must be externally connected together to accommodate total amperage. L1-2 connections must be externally connected together to accommodate total amperage. L1-3 connections must be externally connected together to accommodate total amperage. L1-4 connections must be externally connected together to accommodate total amperage. Output fusing is recommended. Refer to Table 2.B on page 28. 3-12 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Connections Power P Connections Remote R t I/O Connections 1791-0A32 Series B Connector/Terminal Designation Description Left Conn. L1 ac hot 1 N ac neutral 3 Chassis ground 21 GND BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 SHD Shield - RIO 7 Right Conn. I/O Connections Output (G)6 Output (G + 1)7 PLC: out 00 thru 07 SLC: out 00 thru 07 PLC: Output 00 thru 07 SLC: Output 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 L1-1 L1 output supply 10, 12, 142 PLC: out 10 thru 17 SLC: out 08 thru 15 PLC: Output 10 thru 17 SLC: Output 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 L1-2 L1 output supply 9, 11, 133 PLC: out 00 thru 07 SLC: out 00 thru 07 PLC: Output 00 thru 07 SLC: Output 00 thru 07 15, 13, 11, 9, 7, 5, 3, 1 L1-3 L1 output supply 17, 19, 214 PLC: out 10 thru 17 SLC: out 08 thru 15 PLC: Output 10 thru 17 SLC: Output 08 thru 15 16, 14, 12, 10, 8, 6, 4, 2 L1-4 L1 output supply 22, 20, 185 Not used For internal test only; not for customer use. No Conn No internal connection; customer can use. 4, 5 29, 27, 26 30, 28, 25, 24, 23 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 10, 12 and 14 must be externally connected by customer to accommodate total amperage. 3 Terminals 9, 11 and 13 must be externally connected by customer to accommodate total amperage. 4 Terminals 17, 19 and 21 must be externally connected by customer to accommodate total amperage. 5 Terminals 18, 20 and 22 must be externally connected by customer to accommodate total amperage. 6 OUT (G) = output module group (one word). 7 OUT (G + 1) = output module group plus one word. 3-13 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.11 Input/Output Wiring Connections for the 179116AC Series B 1 PLC 1 2 L1 GND NOT USED BLU RIO L1 30 L2/N 30 NO 29 CONN NOT USED NO CONN NOT USED NOT USED NO CONN NO N NOT USED SHD CLR COM COM 1 COM 1 COM 1 NO CONN 2 COM 2 COM 2 L2/N L1-3 in 10 in 01 out 00 L2/N out 01 in 12 out 02 in 02 in 13 in 03 L1 30 out 04 in 15 in 05 in 06 out 03 L1 in 14 in 04 L1-3 L1-3 in 00 in 11 L2/N L1 out 05 in 16 out 06 29 in 17 1 in 07 out 07 1 1 2 BLU RIO L1 in 00 L2/N in 01 in 02 in 03 L1 in 04 in 05 in 06 30 in 07 L1 L2/N L1-4 out 10 out 11 out 12 out 13 out 14 out 15 out 16 2 out 17 30 29 NOT USED N NO CONN L2/N L1-3 L1-3 L2/N in 10 out 00 out 01 out 02 in 11 in 12 L1 L1-3 in 08 in 09 NOT USED NO CONN 2 COM 2 COM 2 L1 in 13 in 16 29 in 15 30 out 03 out 04 out 05 out 06 1 out 07 NO CONN NO CONN NOT USED NOT USED SHD CLR COM COM 1 COM 1 COM 1 L2/N 30 L2/N L1 GND NOT USED L1 L1-4 1 30 SLC CONN L1-4 NO CONN L1-4 L1-4 L1-4 out 08 out 09 out 10 out 11 out 12 out 13 out 14 2 out 15 1 NOTE: COM 1 connections are internally connected together. COM 2 connections are internally connected together. L1-3 connections must be externally connected together to accommodate total amperage. L1-4 connections must be externally connected together to accommodate total amperage. Output fusing is recommended. Refer to Table 2.B on page 28. 3-14 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Connections Power Connections Remote I/O Connections 1791-16AC Series B Connector/Terminal Designation Description Left Conn. L1 ac hot 1 N ac neutral 3 GND Chassis ground 21 BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 SHD Shield - RIO 7 Right Conn. I/O Connections Input (G)6 Output (G)7 in 00 thru in 07 Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 COM 1 L2/N Input Common 10, 12, 142 COM 2 L2/N Input Common 9, 11, 133 PLC: in 10 thru in 17 SLC: in 08 thru in 15 PLC: Input 10 thru 17 SLC: Input 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 PLC: out 00 thru 07 SLC: out 00 thru 07 PLC: Output 00 thru 07 SLC: Output 00 thru 07 15, 13, 11, 9, 7, 5, 3, 1 L1-3 L1 output supply 21, 19, 174 PLC: out 10 thru 17 SLC: out 08 thru 15 PLC: Output 10 thru 17 SLC: Output 08 thru 15 16, 14, 12, 10, 8, 6, 4, 2 L1-4 L1 output supply 22, 20, 185 Not used For internal test only; not for customer use. No Conn No internal connection; customer can use. 4, 5 29, 27, 26 30, 28, 25, 24, 23 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 10, 12 and 14 are internally connected together. 3 Terminals 9, 11 and 13 are internally connected together. 4 Terminals 17, 19 and 21 must be externally connected by customer to accommodate total amperage. 5 Terminals 18, 20 and 22 must be externally connected by customer to accommodate total amperage. 6 IN (G) = input module group. 7 OUT (G) = output module group. 3-15 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.12 Input/Output Wiring Connections for the 179124A8 Series B PLC 1 1 2 L1 GND COM 1 COM 1 NO CONN COM 3 COM 3 COM 3 L2/N in 10 in 00 in 00 in 11 in 01 L2/N in 01 in 12 in 02 in 02 in 13 in 03 L1 in 14 in 04 in 15 in 05 in 06 NOT USED in 03 in 04 L1 in 05 in 16 in 06 29 in 17 30 in 07 1 in 07 SLC 1 1 L1 GND RIO CLR COM 1 COM 1 COM 1 in 00 L2/N in 01 in 02 in 03 L1 in 04 in 05 in 06 30 in 07 30 L1 L2/N L1-4 L1 L2/N L1 L2/N L1-4 L1-4 out 00 out 01 out 02 out 03 out 04 out 05 out 06 2 out 07 30 NOT USED NOT USED NOT USED COM 2 COM 2 COM 2 COM 3 COM 3 COM 3 L2/N in 00 in 09 L2/N in 01 in 10 in 02 in 11 in 13 L1 in 03 in 04 L1 in 05 in 14 29 in 15 NO CONN NO CONN in 08 in 12 NOT USED NO CONN SHD in 06 1 in 07 30 NO CONN NO CONN 29 N NOT USED BLU NO CONN 1 30 2 NOT USED NO CONN COM 2 COM 2 COM 2 COM 1 NO CONN NO CONN 29 NOT USED SHD CLR L1 30 NOT USED BLU L2/N 30 L2/N N NOT USED RIO L1 L1-4 L1-4 L1-4 out 00 out 01 out 02 out 03 out 04 out 05 out 06 2 out 07 1 NOTE: COM 1 connections are internally connected together. COM 2 connections are internally connected together. COM 3 connections are internally connected together. L1-4 connections must be externally connected together to accommodate total amperage. Output fusing is recommended. Refer to Table 2.B on page 28. 3-16 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Connections Power Connections Remote I/O Connections 1791-24A8 Series B Connector/Terminal Designation Description Left Conn. L1 ac hot 1 N ac neutral 3 GND Chassis ground 21 BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 SHD Shield - RIO 7 Right Conn. I/O Connections Input (G)6 Input (G + 1)7 Output (G)8 in 00 thru in 07 Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 COM 1 L2/N Input Common 10, 12, 142 COM 2 L2/N Input Common 9, 11, 133 PLC: in 10 thru in 17 SLC: in 08 thru in 15 PLC: Input 10 thru 17 SLC: Input 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 in 00 thru in 07 Input 00 thru 07 15, 13, 11, 9, 7, 5, 3, 1 COM 3 L2/N Input Common 17, 19, 214 L1-4 L1 Output Supply 22, 20, 185 PLC: out 00 thru out 07 SLC: out 00 thru out 07 PLC: Output 00 thru 07 SLC: Output 00 thru 07 16, 14, 12, 10, 8, 6, 4, 2 Not used For internal test only; not for customer use. No Conn No internal connection; customer can use. 4, 5 29, 27, 26 30, 28, 25, 24, 23 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Left connector terminals 10, 12 and 14 are internally connected together. 3 Left connector terminals 9, 11 and 13 are internally connected together. 4 Right connector terminals 21, 19 and 17 are internally connected together. 5 Right connector terminals 22, 20 and 18 must be externally connected to accommodate total amperage. 6 (IN G) = input module group (1 word). 7 IN (G+1) = input module group plus 1 word. 8 OUT (G) = output module group (1 word). 3-17 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.13 Input/Output Wiring Connections for the 179124AR Series B PLC 1 1 2 L1 GND COM 1 COM 1 COM 1 L2/N in 11 L2/N in 12 in 13 L1 in 14 in 15 in 05 L1 in 16 29 30 in 07 1 in 07 1 1 L1 GND CLR COM 1 COM 1 COM 1 in 00 L2/N in 01 in 02 in 03 L1 in 04 in 05 in 06 30 in 07 30 L1 L2/N/- ac/dc 2 out 07 30 L2/N 30 NOT USED NOT USED NOT USED NO CONN SHD L2/N in 08 in 09 L2/N in 10 in 11 in 13 in 14 29 in 15 NO CONN Vac/dc 4 Vac/dc 4 COM 3 Vac/dc COM 3 4 out 00 in 00 out 01 in 01 out 02 in 02 out 03 in 03 out 04 in 04 out 05 in 05 out 06 COM 3 COM 2 in 12 NOT USED NO CONN COM 2 COM 2 NO CONN NO CONN 29 N NOT USED BLU L1/+ 1 SLC RIO NO CONN Vac/dc 4 Vac/dc 4 COM 3 Vac/dc COM 3 4 out 00 in 00 out 01 in 01 out 02 in 02 out 03 in 03 out 04 in 04 out 05 in 05 out 06 in 06 in 17 30 2 NO CONN COM 3 in 10 in 04 NO CONN NOT USED NO CONN COM 2 in 03 in 06 NO CONN COM 2 in 02 NOT USED NOT USED COM 2 in 01 L1 29 SHD in 00 L2/N 30 NOT USED BLU CLR 30 L2/N N NOT USED RIO L1 L1 L1 in 06 1 in 07 L1/+ L2/N/- ac/dc 2 out 07 1 NOTE: COM 1 connections are internally connected together. COM 2 connections are internally connected together. COM 3 connections are internally connected together. Vac/dc 4 connections must be externally connected together to accommodate maximum amperage. Output fusing is recommended. Size fuse according to output load and surge current requirements. 3-18 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Connections Power Connections Remote I/O Connections 1791-24AR Series B Connector/Terminal Designation Description Left Conn. L1 ac hot 1 N ac neutral 3 GND Chassis ground 21 BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 SHD Shield - RIO 7 Right Conn. I/O Connections Input (G)6 Input (G+1)7 Output (G)8 in 00 thru in 07 Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 COM 1 L2/N Input Common 10, 12, 142 COM 2 L2/N Input Common 9, 11, 133 PLC: in 10 thru in 17 SLC: in 08 thru in 15 PLC: Input 10 thru 17 SLC: Input 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 in 00 thru in 07 Input 00 thru 07 15, 13, 11, 9, 7, 5, 3, 1 COM 3 L2/N Input Common 21, 19, 174 Vac/dc 4 ac or dc Output Supply 22, 20, 185 PLC: out 00 thru out 07 SLC: out 00 thru out 07 PLC: Output 00 thru 07 SLC: Output 00 thru 07 16, 14, 12, 10, 8, 6, 4, 2 Not used For internal test only; not for customer use. No Conn No internal connection; customer can use. 4, 5 29, 27, 26 30, 28, 25, 24, 23 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Left connector terminals 10, 12 and 14 are internally connected together. 3 Left connector terminals 9, 11 and 13 are internally connected together. 4 Right connector terminals 21, 19 and 17 are internally connected together. 5 Right connector terminals 22, 20 and 18 must be externally connected to accommodate total amperage. 6 IN (G) = input module group (1 word). 7 IN (G+1) = input module group plus 1 word. 8 OUT (G) = output module group (1 word). 3-19 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.14 Input Wiring Connections for the 179116B0 Series B 1 PLC RIO 1 2 GND NOT USED BLU NOT USED RET 1 RET 1 + +24 24V dc 1 SLC 2 RIO BLU in 01 in 02 in 03 in 04 in 05 in 06 in 07 RET 2 RET 1 in 11 in 12 24V dc 24V dc in 13 + + in 00 in 01 in 02 in 03 in 14 in 04 in 15 in 05 in 16 in 06 in 17 in 07 30 in 08 in 09 in 10 24V dc in 11 + in 12 in 13 in 14 in 15 30 NOTE: Ret 1 connections are internally connected together. Ret 2 connections are internally connected together. Connections 179116B0 Series B Designation Description Terminal No. P Power Connections +24 +24V dc Power 1 RET +24 dc Return 3 GND Chassis ground 21 Remote R t I/O Connections BLU Blue wire RIO 6 CLR Clear wire RIO 8 SHD Shield RIO 7 I/O Connections Input Input RET 2 RET 1 in 10 24V dc NOT USED NOT USED RET 2 + SHD CLR NOT USED RET 2 +24 RET +24 NOT USED NOT USED SHD in 00 1 GND RET +24 NOT USED CLR 24V dc + in 00 thru in 07 Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 RET 1 RET 1 Input Common 12, 142 RET 2 RET 2 Input Common 11, 133 PLC: in 10 thru in 17 SLC: in 08 thru in 15 PLC: Input 10 thru input 17 SLC: Input 08 thru input 15 15, 17, 19, 21, 23, 25, 27, 29 Not Used For internal test only; not for customer use. 4, 5, 9, 10 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 12 and 14 are internally connected. 3 Terminals 11 and 13 are internally connected. 3-20 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.15 Output Wiring Connections for the 17910B16 Series B 1 PLC 2 GND NOT USED RIO BLU CLR 24V dc + RET 1 Vdc 1 Vdc 1 out 00 out 01 out 02 out 03 out 04 out 05 out 06 30 out 07 1 +24 + 24V dc RET +24 NOT USED Vdc 2 2 GND 24V dc out 10 BLU 24V dc RET 2 Vdc 2 Vdc 2 out 00 out 11 out 01 out 12 out 02 out 13 out 03 out 14 out 04 out 15 out 05 out 16 out 06 29 out 17 30 24V dc 24V dc SHD RET 1 Vdc 1 Vdc 1 + + NOT USED CLR + 1 +24 RET +24 NOT USED RIO SHD RET 2 Vdc 2 1 SLC out 07 + out 08 out 09 out 10 out 11 out 12 out 13 out 14 29 out 15 30 30 Note: Vdc 1 connections must be externally connected together to accommodate amperage rating. Vdc 2 connections must be externally connected together to accommodate amperage rating. Output fusing is recommended. Refer to Table 2.B on page 28. Connections Power Connections Remote I/O Connections 17910B16 Series B Designation Description Terminal No. +24 +24V dc Power 1 RET +24 dc Return 3 GND Chassis ground 21 BLU Blue wire RIO 6 CLR Clear wire RIO 8 SHD Shield RIO 7 I/O Connections Output p Output out 00 thru out 07 Output 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 Vdc 1 +24V dc output supply 12, 142 RET 1 dc output return 10 Vdc 2 +24V dc output supply 11, 133 RET 2 dc output return 9 PLC: out 10 thru out 17 SLC: out 08 thru out 15 PLC: Output 10 thru 17 SLC: Output 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 Not used For internal test only; not for customer use. 4, 5 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 12 and 14 must be externally connected by customer to accommodate amperage rating. 3 Terminals 11 and 13 must be externally connected by customer to accommodate amperage rating. 3-21 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.16 Input/Output Wiring Connections for the 17918BC Series B 1 PLC and SLC 1 2 GND NOT USED RIO BLU CLR + 24V dc NOT USED RET in RET in in 00 in 01 in 02 in 03 in 04 in 05 in 06 30 in 07 +24 + 24V dc RET +24 NOT USED SHD RET out Vdc out Vdc out + 24V dc out 00 out 01 out 02 out 03 out 04 out 05 out 06 29 out 07 30 NOTE: RET in connections are internally connected together. Vdc out connections must be externally connected together to accommodate amperage rating. Output fusing is recommended. Refer to Table 2.B on page 28. Connections Power Connections Remote I/O Connections 17918BC Series B Designation Description Terminal No. +24 +24V dc Power 1 RET +24 dc Return 3 GND Chassis ground 21 BLU Blue wire RIO 6 CLR Clear wire RIO 8 SHD Shield RIO 7 I/O Connections Input Output p 1 2 3 in 00 thru in 07 Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 RET in dc input Return 12, 142 Vdc out dc output Supply 11, 133 RET out dc output Return 9 out 00 thru out 07 Output 00 thru 07 15, 17, 19, 21, 23, 25, 27, 29 Not used For internal test only; not for customer use. 4, 5, 10 Connect chassis ground to equipment grounding stud. These are not internally connected. Terminals 12 and 14 are internally connected. Terminals 11 and 13 must be externally connected by customer to accommodate amperage rating. 3-22 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.17 Input/Output Wiring Connections for the 17918BR Series B 1 PLC and SLC 1 2 GND NOT USED RIO BLU CLR + 24V dc + +24 RET +24 in 00 in 01 in 02 in 03 in 04 in 05 in 06 30 in 07 - NOT USED SHD NOT NOT USED USED Vac/dc out RET Vac/dc in out RET in out 00 - 24V dc L1/+ L2N/ac/dc out 01 out 02 out 03 out 04 out 05 out 06 29 out 07 30 NOTE: RET in connections are internally connected together. Vac/dc out connections must be externally connected together to accommodate amperage rating. Output fusing is recommended. Refer to Table 2.B on page 28. Connections Power Connections Remote I/O Connections 12399-I 1791-8BR Series B Designation Description Terminal No. +24 +24V dc Power 1 RET +24 dc Return 3 GND Chassis ground 21 BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 SHD Shield - RIO 7 I/O Connections Input Output 1 2 3 in 00 thru in 07 Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 RET in dc input Return 12, 142 Vac/dc out ac or dc Output Supply 11, 133 out 00 thru out 07 Output 00 thru 07 15, 17, 19, 21, 23, 25, 27, 29 Not used For internal test only; not for customer use. 4, 5, 9, 10 Connect chassis ground to equipment grounding stud. These are not internally connected. Terminals 12 and 14 are internally connected. Terminals 11 and 13 must be externally connected by customer to accommodate amperage rating. 3-23 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.18 Input Wiring Connections for the 179132B0 Series B PLC 1 1 2 +24 GND + 24V dc 30 29 - 24V dc + + 24V dc - in 06 in 17 in 07 1 1 RIO + 24V dc - CLR in 00 in 01 in 02 in 03 in 04 in 05 in 06 30 in 07 30 30 24V dc - 30NO 29 NOT CONN USED NO CONN NOT USED NOT USED NO CONN NO CONN NO CONN NOT RET +24 NOT USED SHD NOT USED NOT USED RET 1 RET 1 + +24 NOT USED BLU in 17 1 SLC GND in 16 2 1 30 2 in 15 in 05 in 16 in 07 in 14 in 04 29 30 in 13 in 03 in 15 in 05 in 12 in 02 in 14 in 04 in 11 in 01 in 13 in 03 - 24V dc + in 10 in 00 in 12 in 02 RET 4 RET 4 RET 3 RET 3 in 11 in 01 NOT USED NOT USED in 10 in 00 NOT USED NO CONN NO CONN RET 2 RET 2 RET 1 RET 1 NOT USED NO CONN NOT USED NOT USED NO CONN NO CONN NOT USED SHD CLR in 06 30 - NOT USED BLU - 24V dc RET +24 NOT USED RIO + RET 2 RET 2 in 08 in 09 in 10 in 11 in 12 in 13 in 14 29 in 15 - 24V dc + + 24V dc - USED NOT USED RET 4 RET 4 RET 3 RET 3 in 08 in 00 in 09 in 01 in 10 in 02 in 11 in 03 in 12 in 04 in 13 in 05 in 06 1 in 07 - 24V dc + in 14 2 in 15 1 NOTE: RET 1 connections are internally connected together. RET 2 connections are internally connected together. RET 3 connections are internally connected together. RET 4 connections are internally connected together. 3-24 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Connections 1791-32B0 Series B Connector/Terminal Designation Description Left Power P Connections +24 +24V dc Power 1 RET +24 dc Return 3 Chassis ground 21 Remote R t I/O Connections BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 Shield - RIO 7 GND SHD Right I/O Connections Input (G)6 Input (G + 1)7 PLC: in 00 thru 07 SLC: in 00 thru 07 PLC: Input 00 thru 07 SLC: Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 RET 1 dc input return 12, 142 PLC: in 10 thru 17 SLC: in 08 thru 15 PLC: Input 10 thru 17 SLC: Input 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 RET 2 dc input return 11, 133 PLC: in 00 thru 07 SLC: in 00 thru 07 PLC: Input 00 thru 07 SLC: Input 00 thru 07 15, 13, 11, 9, 7, 5, 3, 1 RET 3 dc input return 19, 174 PLC: in 10 thru 17 SLC: in 08 thru 15 PLC: Input 10 thru 17 SLC: Input 08 thru 15 16, 14, 12, 10, 8, 6, 4, 2 RET 4 dc input return 20, 185 Not used For internal test only; not for customer use. No Conn No internal connection; customer can use. 4, 5, 9, 10 29, 27, 26, 22, 21 30, 28, 25, 24, 23 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 12 and 14 are internally connected together. 3 Terminals 11 and 13 are internally connected together. 4 Terminals 19 and 17 are internally connected together. 5 Terminals 20 and 18 are internally connected together. 6 IN (G) = input module group. 7 IN (G + 1) = input module group plus 1. 3-25 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.19 Output Wiring Connections for the 17910B32 Series B PLC 1 1 2 GND BLU _ CLR 24V dc RET 1 Vdc 1 Vdc 1 + out 00 out 01 out 02 out 03 out 04 out 05 out 06 30 out 07 + 24V dc 30 _ SHD NO CONN + 24V dc _ _ RET 3 Vdc 3 Vdc 3 24V dc + out 10 out 00 out 11 out 01 out 12 out 02 out 13 out 03 out 14 out 04 out 15 out 05 out 16 out 06 29 out 17 1 1 NOT USED RIO BLU CLR _ 24V dc + RET 1 Vdc 1 Vdc 1 out 00 out 01 out 02 out 03 out 04 out 05 out 06 30 out 07 30 NOT USED 1 out 07 NO CONN RET 4 Vdc 4 Vdc 4 + 24V dc _ out 10 out 11 out 12 out 13 out 14 out 15 out 16 2 out 17 1 SLC GND NO CONN NO CONN 30 2 CONN NOT USED NOT USED NOT USED RET 2 Vdc 2 Vdc 2 30 NO 29 RET +24 NOT USED RIO +24 +24 + 24V dc 30 _ 29 RET +24 out 08 out 09 out 10 out 11 out 12 out 13 out 14 29 out 15 NOT USED NO CONN SHD Vdc 2 NO CONN NOT USED NOT USED RET 2 Vdc 2 NOT USED 30 NO CONN NO CONN NO CONN + 24V dc _ _ 24V dc RET 3 Vdc 3 Vdc 3 + out 00 out 01 out 02 out 03 out 04 out 05 out 06 1 out 07 RET 4 Vdc 4 + 24V dc _ Vdc 4 out 08 out 09 out 10 out 11 out 12 out 13 out 14 2 out 15 1 Note: Vdc 1 connections must be externally connected together to accommodate amperage rating. Vdc 2 connections must be externally connected together to accommodate amperage rating. Vdc 3 connections must be externally connected together to accommodate amperage rating. Vdc 4 connections must be externally connected together to accommodate amperage rating. Output fusing is recommended. Refer to Table 2.B on page 28. 3-26 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Connections 1791-0B32 Series B Connector/Terminal Designation Description Left Power P Connections +24 +24V dc Power 1 RET +24 dc Return 3 Chassis ground 21 Remote R t I/O Connections BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 Shield - RIO 7 GND SHD Right I/O Connections Output (G)6 Output (G + 1)7 PLC: out 00 thru 07 SLC: out 00 thru 07 PLC: Output 00 thru 07 SLC: Output 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 Vdc 1 +24V dc output supply 12, 142 RET 1 dc output return 10 PLC: out 10 thru 17 SLC: out 08 thru 15 PLC: Output 10 thru 17 SLC: Output 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 Vdc 2 +24V dc output supply 11, 133 RET 2 dc output return 9 PLC: out 00 thru 07 SLC: out 00 thru 07 PLC: Output 00 thru 07 SLC: Output 00 thru 07 15, 13, 11, 9, 7, 5, 3, 1 Vdc 3 +24V dc output supply 19, 174 RET 3 dc output return 21 PLC: out 10 thru 17 SLC: out 08 thru 15 PLC: Output 10 thru 17 SLC: Output 08 thru 15 16, 14, 12, 10, 8, 6, 4, 2 Vdc 4 +24V dc output supply 20, 185 RET 4 dc output return 22 Not used For internal test only; not for customer use. No Conn No internal connection; customer can use. 4, 5 29, 27, 26 30, 28, 25, 24, 23 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 12 and 14 must be externally connected by customer to accommodate amperage rating. 3 Terminals 11 and 13 must be externally connected by customer to accommodate amperage rating. 4 Terminals 19 and 17 must be externally connected by customer to accommodate amperage rating. 5 Terminals 20 and 18 must be externally connected by customer to accommodate amperage rating. 6 OUT (G) = output module group. 7 OUT (G + 1) = output module group plus 1. 3-27 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.20 Input/Output Wiring Connections for the 179116BC Series B 1 1 2 GND NOT USED NOT USED RET 2 RET 2 RET 1 RET 1 in 01 in 02 in 03 in 04 in 05 in 06 30 in 07 30 out 06 1 RET 4 Vdc 4 Vdc 4 + 24V dc _ out 10 out 11 out 12 out 13 out 14 out 15 out 16 2 out 17 1 1 in 00 out 05 NO CONN out 07 1 RET 1 RET 1 out 04 in 17 SLC + 24V dc - out 03 29 in 07 30 NOT USED out 02 in 16 30 CLR out 01 in 15 in 05 RIO out 00 in 14 in 04 BLU 24V dc RET 3 Vdc 3 Vdc 3 + in 13 in 03 NOT USED _ in 12 in 02 GND - 24V dc + in 11 in 01 NOT USED NO CONN NO CONN NO CONN NO CONN NOT USED in 10 in 00 2 30 29 NOT USED SHD CLR in 06 - NOT USED BLU + 24V dc - + 24V dc RET +24 NOT USED RIO +24 30 PLC +24 + 24V dc 30 29 NOT USED RET +24 NO CONN - 24V dc + _ 24V dc RET 3 Vdc 3 Vdc 3 + in 08 in 09 in 10 in 11 in 12 out 00 out 01 out 02 out 03 in 13 out 04 in 14 out 05 29 in 15 NOT USED NO CONN SHD RET 2 RET 2 CONN NO CONN NOT USED NOT USED NOT USED 30 NO out 06 1 out 07 NO CONN RET 4 Vdc 4 Vdc 4 + 24V dc _ out 08 out 09 out 10 out 11 out 12 out 13 out 14 2 out 15 1 NOTE: RET 1 connections are internally connected. RET 2 connections are internally connected. Vdc 3 connections must be externally connected to accommodate amperage rating. Vdc 4 connections must be externally connected to accommodate amperage rating. Output fusing is recommended. Refer to Table 2.B on page 28. 3-28 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Connections 1791-16BC Series B Connector/Terminal Designation Description Left Power P Connections +24 +24V dc Power 1 RET +24 dc Return 3 Chassis ground 21 Remote R t I/O Connections BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 Shield - RIO 7 GND SHD Right I/O Connections Input (G)6 Output (G)7 PLC: in 00 thru 07 SLC: in 00 thru 07 PLC: Input 00 thru 07 SLC: Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 RET 1 dc input return 12, 142 PLC: in 10 thru 17 SLC: in 08 thru 15 PLC: Input 10 thru 17 SLC: Input 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 RET 2 dc input return 11, 133 PLC: out 00 thru 07 SLC: out 00 thru 07 PLC: Output 00 thru 07 SLC: Output 00 thru 07 15, 13, 11, 9, 7, 5, 3, 1 Vdc 3 +24V dc output supply 19, 174 RET 3 dc output return 21 PLC: out 10 thru 17 SLC: out 08 thru 15 PLC: Output 10 thru 17 SLC: Output 08 thru 15 16, 14, 12, 10, 8, 6, 4, 2 Vdc 4 +24V dc output supply 20, 185 RET 4 dc output return 22 Not used For internal test only; not for customer use. No Conn No internal connection; customer can use. 4, 5, 9, 10 29, 27, 26 30, 28, 25, 24, 23 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 12 and 14 are internally connected. 3 Terminals 11 and 13 are internally connected. 4 Terminals 17 and 19 must be externally connected by customer to accommodate amperage rating. 5 Terminals 20 and 18 must be externally connected by customer to accommodate amperage rating. 6 IN (G) = input module group. 7 OUT (G) = output module group. 3-29 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.21 Input/Output Wiring Connections for the 179124B8 Series B PLC 1 1 2 GND NOT USED BLU RIO + CLR 24V dc _ NOT USED RET 1 RET 1 in 00 in 01 in 02 in 03 in 04 in 05 in 06 30 in 07 + +24 24V dc 30 _ 29 NOT USED RET +24 NOT USED NOT USED NO CONN SHD NOT USED RET 2 RET 2 NO CONN _ 24V dc + + 24V dc _ in 10 in 11 in 01 in 12 in 02 in 13 in 03 in 14 in 04 in 15 in 05 in 16 in 06 29 in 17 1 1 1 NOT USED BLU RIO + CLR 24V dc _ NOT USED RET 1 RET 1 in 00 in 01 in 02 in 03 in 04 in 05 in 06 30 in 07 30 in 07 NO CONN NOT USED NO CONN RET 4 Vdc 4 Vdc 4 + 24V dc _ out 00 out 01 out 02 out 03 out 04 out 05 out 06 2 out 07 1 SLC GND RET 3 RET 3 in 00 30 2 NOT USED 30 NO CONN + +24 24V dc 30 _ 30 NO 29 NOT CONN USED NO CONN NOT NOT USED USED NO CONN NO CONN NO CONN RET RET +24 NOT USED SHD NOT USED RET 2 RET 2 _ 24V dc + + 24V dc RET 3 RET 3 in 08 in 00 in 09 in 01 in 10 in 02 in 11 in 03 in 12 in 04 in 13 in 05 in 14 29 in 15 4 Vdc 4 Vdc 4 NOT USED _ in 06 1 in 07 + 24V dc _ out 00 out 01 out 02 out 03 out 04 out 05 out 06 2 out 07 1 NOTE: RET 1 connections are internally connected together. RET 2 connections are internally connected together. RET 3 connections are internally connected together. Vdc 4 connections must be externally connected together to accommodate amperage rating. Output fusing is recommended. Refer to Table 2.B on page 28. 3-30 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Connections 1791-24B8 Series B Connector/Terminal Designation Description Left Conn. Power P Connections +24 +24V dc Power 1 RET +24 dc Return 3 Chassis ground 21 Remote R t I/O Connections BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 Shield - RIO 7 GND SHD Right Conn. I/O Connections Input (G)6 Input (G + 1)7 Output ((G))8 PLC: in 00 thru 07 SLC: in 00 thru 07 PLC: Input 00 thru 07 SLC: Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 RET 1 dc input return 12, 142 PLC: in 10 thru 17 SLC: in 08 thru 15 PLC: Input 10 thru 17 SLC: Input 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 RET 2 dc input return 11, 133 PLC: in 00 thru 07 SLC: in 00 thru 07 PLC: Input 00 thru 07 SLC: Input 00 thru 07 15, 13, 11, 9, 7, 5, 3, 1 RET 3 dc input return 19, 174 PLC: out 00 thru 07 SLC: out 00 thru 07 PLC: Output 00 thru 07 SLC: Output 00 thru 07 16, 14, 12, 10, 8, 6, 4, 2 V dc 4 dc output supply 20, 185 RET 4 dc output return 22 Not used For internal test only; not for customer use. No Connection No internal use; customer can use. 4, 5, 9, 10 29, 27, 26, 21 30, 28, 25, 24, 23 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 12 and 14 are internally connected. 3 Terminals 11 and 13 are internally connected. 4 Terminals 17 and 19 are internally connected. 5 Terminals 20 and 18 must be externally connected by customer to accommodate amperage rating. 6 IN G = input module group. 7 IN (G + 1) = input module group plus 1. 8 OUT (G) = output module group. 3-31 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.22 Input/Output Wiring Connections for the 179124BR Series B PLC 1 1 2 GND +24 + NOT USED NOT USED _ RET 2 RET 2 RET 1 RET 1 24V dc + + 24V dc _ RET 3 RET 3 in 00 in 01 in 02 in 13 in 03 in 03 in 14 in 04 in 04 in 15 in 05 30 _ NOT USED in 12 in 02 in 05 in 16 in 06 29 in 17 in 07 1 SLC 1 1 GND NOT USED BLU RIO + CLR 24V dc _ NOT USED RET 1 RET 1 in 00 in 01 in 02 in 03 in 04 in 05 in 06 30 in 07 30 NO CONN in 07 NOT USED L1/+ Vac/dc 4 Vac/dc 4 L2N/ac/dc out 00 out 01 out 02 out 03 out 04 out 05 out 06 2 out 07 1 30 2 NOT USED NO CONN in 11 in 01 in 06 NOT USED NO CONN in 10 in 00 CONN NO CONN NOT USED SHD CLR 30 NO 29 NOT USED BLU 24V dc 24V dc 30 _ RET +24 NOT USED RIO + + +24 24V dc 30 _ 30 NO 29 NOT CONN USED NO CONN NOT NOT USED USED NO CONN NO CONN NO CONN NOT USED NOT RET +24 NOT USED SHD NOT USED RET 2 RET 2 _ 24V dc + + 24V dc USED _ RET 3 RET 3 in 08 in 00 in 09 in 01 in 10 in 02 in 11 in 03 in 12 in 04 in 13 in 05 in 14 29 in 15 in 06 1 in 07 Vac/dc 4 Vac/dc 4 L1/+ L2N/ac/dc out 00 out 01 out 02 out 03 out 04 out 05 out 06 2 out 07 1 NOTE: RET 1 connections are internally connected together. RET 2 connections are internally connected together. RET 3 connections are internally connected together. Vac/dc 4 connections must be externally connected together to accommodate amperage rating. Output fusing is recommended. Size fuse according to output load and surge current requirements. 3-32 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Connections 1791-24BR Series B Connector/Terminal Designation Description Left Conn. Power P Connections +24 +24V dc Power 1 RET +24 dc Return 3 Chassis ground 21 Remote R t I/O Connections BLU Blue wire - RIO 6 CLR Clear wire - RIO 8 Shield - RIO 7 GND SHD Right Conn. I/O Connections Input (G)6 Input (G + 1)7 Output (G)8 PLC: in 00 thru 07 SLC: in 00 thru 07 PLC: Input 00 thru 07 SLC: Input 00 thru 07 16, 18, 20, 22, 24, 26, 28, 30 RET 1 dc input return 12, 142 PLC: in 10 thru 17 SLC: in 08 thru 15 PLC: Input 10 thru 17 SLC: Input 08 thru 15 15, 17, 19, 21, 23, 25, 27, 29 RET 2 dc input return 11, 133 PLC: in 00 thru 07 SLC: in 00 thru 07 PLC: Input 00 thru 07 SLC: Input 00 thru 07 15, 13, 11, 9, 7, 5, 3, 1 RET 3 dc input return 19, 174 PLC: out 00 thru 07 SLC: out 00 thru 07 PLC: Output 00 thru 07 SLC: Output 00 thru 07 16, 14, 12, 10, 8, 6, 4, 2 Vac/dc 4 ac or dc output supply 20, 185 Not used For internal test only; not for customer use. No Connection No internal use; customer can use. 4, 5, 9, 10 29, 27, 26, 22, 21 30, 28, 25, 24, 23 1 Connect chassis ground to equipment grounding stud. These are not internally connected. 2 Terminals 12 and 14 are internally connected. 3 Terminals 11 and 13 are internally connected. 4 Terminals 19 and 17 are internally connected. 5 Terminals 20 and 18 must be externally connected by customer to accommodate amperage rating. 6 IN G = input module group. 7 IN (G + 1) = input module group plus 1. 8 OUT (G) = output module group. Table 3.B Acceptable Wiring Cables for Block I/O Connection Use Cable Type Remote I/O link Belden 9463 Input and output wiring Up to 14AWG (2mm2) stranded with 3/64 inch insulation 3-33 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Termination Resistor A termination resistor must be installed on the last block in a series. Connect the resistor as shown in Figure 3.23. Figure 3.23 Installing the Termination Resistor Connect termination resistor across terminals 6 (BLU) and 8 (CLR). BLU Refer to Table 3.A for proper terminator for your application. CLR SHD Termination Resistor Surge Suppression 10835I Output modules contain surge suppression circuitry for the block output devices. The ac output modules provide an RC network to limit the magnitude of voltage transients that may occur when a device is wired in parallel or series with hard contacts. The dc output modules have clamping diodes that shunt voltage transients to the power supply. Important: We recommend that you use an additional suppression device if an output module is being used to control an inductive device such as: relays solenoids motor starters motors and is in series with or parallel to a “hard contact” such as: pushbuttons selector switches By adding a suppression device directly across the coil of an inductive device, you will prolong the life of the output devices and switch contacts. Figure 3.24 shows an output module with a suppression device. 3-34 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Figure 3.24 Connecting Surge Suppression Devices L1 GND NOT USED BLU N NOT USED L2/N L1 SHD CLR COM in COM in COM in in 00 in 01 COM out COM out snubber COM out out 00 out 01 out 02 Load in 02 out 03 in 03 in 04 out 04 out 05 in 05 in 06 out 06 out 07 in 07 12346I The impedance characteristic is the most important factor in selecting a suppression device; thus no single suppression device can be recommended for every possible load. Table 3.C shows acceptable Allen-Bradley suppression devices and their catalog numbers for typical loads. Table 3.C AllenBradley Suppression Devices Suppression Device Catalog Number Motor Starter Bulletin 509 599K041 Relay Bulletin 700 Type N or P 700N241 Miscellaneous 700N242 1 Maximum coil voltage 150V ac or dc 2 Bulletin 700N24 is a universal surge suppressor. You can use it on electromagnetic devices with the limitation of 35 sealed VA, 150V. 3-35 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Remote I/O Link Wiring Blocks must be wired in series as shown in Figure 3.25 or Figure 3.26. Do not attempt to wire any block in parallel. The number of blocks used depends not only on the user requirements but also on the system used. Refer to Table 3.A (page 3-1) for maximum block usage for individual systems. Figure 3.25 Series Connection for Block I/O Using PLC2, PLC3 or PLC5 Family Programmable Controllers To Programmable Controller or I/O Scanner Module 1 I/O Rack 1 I/O Rack 1 I/O Rack 1 I/O Rack Install terminating resistor on last block. 3-36 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com 10833I Chapter 3 Installing Block I/O Figure 3.26 Series Configurations for Block I/O Using the SLC Programmable Controller To 1747SN Scanner Module 1 2 15 16 Up to 16 blocks with SLC5/02 or SLC5/03 Install terminating resistor on last block. Extended Node Capability 10834I If this is the last remote I/O adapter on the remote I/O link in a PLC system, you must use a terminating resistor to terminate both ends of the remote I/O link (scanner end and last block end). The size of the terminator is determined by the system configuration. Older system configurations must use a 150 ohm resistor at both ends. With newer devices that can support it, you can use an 82 ohm termination resistor at both ends. The 82 ohm terminators provide “extended node” capability which allows you to have up to 32 physical devices on the remote I/O link. (The number of logical racks capable of being addressed by the scanner is not affected.) ATTENTION: Devices that are operating at 230.4K baud must have 82 ohm terminators in place for proper operation. 3-37 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 3 Installing Block I/O Compatibility of 1771 I/O Products with Extended Node Numbers Certain products are not compatible with extended node capabilities obtained with the use of 82 ohm terminators. Table 3.D lists those products that are not compatible. Table 3.D Noncompatible Products Device Scanners Adapters Miscellaneous Selecting Remote I/O Link Speed Series 1771SN All 1772SD All 1772SD2 All 1775SR All 1775S4A All 1775S4B All 1771AS All 1771ASB Series A 1771DCM All 1771AF All 1771AF1 All The remote I/O link can operate at three speeds: 57.6K, 115.2K or 230.4K bits/s. The selection of link speed is dependent on the scanner/processor used, throughput requirements, distance required and the type of remote I/O devices being used. Throughput Requirements The throughput, a portion of which is I/O scan time, must be balanced against the distance requirements for the application. The typical discrete I/O scan time is shown in Table 3.E below. Use these values along with your processor/scanner manual to determine system throughput. Table 3.E I/O Scan Time vs. Remote I/O Link Distance 57.6K Bits/s 115.2K Bits/s 230.4K Bits/s Typical Discrete I/O Scan Time (each block) 10ms 7.0ms 3ms Remote I/O link distance 10,000 ft. 5,000 ft. 2,500 ft. 3-38 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Chapter Objectives In this chapter, you will learn how to configure your block I/O when used with PLC family programmable controllers. This includes the following: setting the configuration switches addressing the block I/O Setting the Configuration Switches Each block I/O module has two 8-position switches for setting: starting I/O group I/O rack number communication rate last chassis last state complementary I/O input filter speed (dc inputs only) processor restart/lockout These switches are accessible by opening the clear plastic door on the front of the module (Figure 4.1). ATTENTION: Cycle power to the block I/O module after setting the switches. 4-1 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Figure 4.1 Switch Settings for the ac and dc Block I/O Modules (16point illustrated) 179116B0 Default Switch Settings = 0 24V dc INPUT 7 8 1 6 dc Applications SW2-7 Filter Speed Select 0 Slow 1 Fast Note: For inputs only ac Applications SW2-7 Not Used 5 SW2 4 10 11 12 13 14 15 16 17 3 00 01 02 03 04 05 06 07 INPUT 1 2 INPUT SW2-8 Not used 1 7 8 0 SW2-5 0 1 SW2-4 0 1 Last I/O Group Not last rack Last rack Processor Restart/Lockout (PRL) Processor Restart Processor Lockout Hold Last State Reset Outputs Hold Last State 4 5 6 SW1 SW2-6 0 1 1 2 3 30 Open cover to access switches 0 Position = 0 1 Position = 1 End View ATTENTION: Cycle power to the module after setting the switches. NOTE: Only block I/O modules with all inputs or all outputs can use complementary I/O. Series A block I/O modules do not support complementary I/O. If using series A modules, set this switch to 0. Set switch SW2-3 to 0 if this rack will have a unique address (not complemented). If this rack address is a duplicate of another I/O block or chassis, set the switch to 1 for primary or 0 for complementary. Refer to Table 4.G for the complementary I/O rack address. SW2-3 0 Complementary I/O1 NonCompleted Systems 0 Complementary Rack1 1 Primary Rack1 1 See Note. Communication Rate SW2-2 SW2-1 Bits/s 0 0 57.6 K 0 1 115.2 K 1 0 230.4 K 1 1 230.4 K SW1-3 thru 8 Rack Address Refer to Table 4.F for settings. SW1-2 0 0 1 1 Starting Quarter SW1-1 Module Group 0 0 (1st) 1 2 (2nd) 0 4 (3rd) 1 6 (4th) 12403-I 4-2 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Table 4.F Switch Settings for Block I/O (Primary Rack) 1747SN Rack Number Rack 0 Rack 1 Rack 2 Rack 3 1771SN Rack Number Rack 1 Rack 2 Rack 3 Rack 4 Rack 5 Rack 6 Rack 7 PLC-2 Rack Number Rack 1 Rack 2 Rack 3 Rack 4 Rack 5 Rack 6 Rack 7 PLC-5 Rack Number Not Valid Rack 1 Rack 2 Rack 3 Rack 4 Rack 5 Rack 6 Rack 7 Rack 10 Rack 11 Rack 12 Rack 13 Rack 14 Rack 15 Rack 16 Rack 17 Rack 20 Rack 21 Rack 22 Rack 23 Rack 24 Rack 25 Rack 26 Rack 27 PLC-5/250 Rack Number Rack 0 Rack 1 Rack 2 Rack 3 Rack 4 Rack 5 Rack 6 Rack 7 Rack 10 Rack 11 Rack 12 Rack 13 Rack 14 Rack 15 Rack 16 Rack 17 Rack 20 Rack 21 Rack 22 Rack 23 Rack 24 Rack 25 Rack 26 Rack 27 Rack 30 Rack 31 Rack 32 Rack 33 Rack 34 Rack 35 Rack 36 Rack 37 PLC-3 Rack Number Rack 0 Rack 1 Rack 2 Rack 3 Rack 4 Rack 5 Rack 6 Rack 7 Rack 10 Rack 11 Rack 12 Rack 13 Rack 14 Rack 15 Rack 16 Rack 17 Rack 20 Rack 21 Rack 22 Rack 23 Rack 24 Rack 25 Rack 26 Rack 27 Rack 30 Rack 31 Rack 32 Rack 33 Rack 34 Rack 35 Rack 36 Rack 37 Rack 40 Rack 41 Rack 42 Rack 43 Rack 44 Rack 45 Rack 46 Rack 47 Rack 50 SW1 Switch Position 8 7 6 5 4 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 4-3 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers 1747SN Rack Number 1771SN Rack Number PLC-2 Rack Number PLC-5 Rack Number PLC-5/250 Rack Number PLC-3 Rack Number Rack 51 Rack 52 Rack 53 Rack 54 Rack 55 Rack 56 Rack 57 Rack 60 Rack 61 Rack 62 Rack 63 Rack 64 Rack 65 Rack 66 Rack 67 Rack 70 Rack 71 Rack 72 Rack 73 Rack 74 Rack 75 Rack 76 Not Valid SW1 Switch Position 8 7 6 5 4 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Rack address 77 is an illegal configuration. PLC5/11 processors can scan rack 03. PLC5/15 and PLC5/20 processors can scan racks 01-03. PLC5/25 and PLC5/30 processors can scan racks 01-07. PLC5/40 and PLC5/40L processors can scan racks 01-17. PLC5/60 and PLC5/60L processors can scan racks 01-27. PLC5/250 processors can scan racks 00-37. Table 4.G Switch Settings for Block I/O as Complementary I/O (PLC-2 and PLC-5 only) SW1 Switch Position PLC-2 Rack Number PLC-5 Rack Number 8 7 6 5 4 3 Rack 1 Not Valid 0 0 1 0 0 0 Rack 2 Rack 1 0 0 1 0 0 1 Rack 3 Rack 2 0 0 1 0 1 0 Rack 4 Rack 3 0 0 1 0 1 1 Rack 5 Rack 4 0 0 1 1 0 0 Rack 6 Rack 5 0 0 1 1 0 1 Rack 7 Rack 6 0 0 1 1 1 0 Rack 7 0 0 1 1 1 1 ATTENTION: Series A modules do not support complementary I/O. When configured as complementary I/O: ● ● ● PLC2 can scan racks 01-07 PLC5/11 can scan rack 03 PLC5/20, PLC5/30, PLC5/40, PLC5/60 can scan racks 01-07 4-4 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers The SLC 500 controllers communicate with the block I/O using an I/O Scanner module (cat. no. 1747-SN series A). Refer to the user manual for the 1747-SN/A Scanner module for more information. Note: These block I/O modules are not compatible with the 1747-DSN Distributed I/O Scanner module. Each block I/O module uses 2 words of output image table memory and 2 words of input image table memory. Each block occupies 1/4 rack of data table, with 4 blocks comprising 1 logical rack. Image table usage for one assigned rack number and examples of image table usage are shown in Figures 4.2 through 4.10. Figure 4.2 I/O Image Table for One Assigned Rack Number with 16point Modules 17918AC 17910B16 179116B0 179116A0 0 1 2 3 4 5 6 7 15 17 0 SLC 0 PLC Reserved Reserved Reserved Reserved Reserved Reserved 1 I/O Rack 15 17 0 1 2 3 4 5 6 7 Input Image 8 7 10 7 Output Image 8 7 10 7 Reserved Reserved Reserved Reserved 0 SLC 0 PLC Reserved Reserved Reserved 4-5 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Figure 4.3 Input/Output Image Table Usage Example for One Starting I/O Group for 16 Output Modules (cat. no. 17910A16, 0B16) PLC2 Example 0 1 0 00 Type of I/O 1 = Input 0 = Output PLC3, PLC5, PLC5/250 Example O 1 0 00 I/O Bit I/O Group Number I/O Rack Number I/O Bit I/O Group Number I/O Rack Number Reserved 11 10 Reserved 110 111 Starting I/O Group 0 Type of I/O I = Input O = Output Input Image Block Data 010 17 16 15 14 13 12 11 10 7 6 5 4 3 2 1 0 11 10 Reserved 011 Output Image Block Data 10838I Figure 4.4 Input/Output Image Table Usage Example for One Starting I/O Group with 16 Input Modules (cat. no. 179116A0, 16B0) PLC2 Example 1 1 0 00 Type of I/O 1 = Input 0 = Output 110 I 1 0 00 Type of I/O I = Input O = Output I/O Bit I/O Group Number I/O Rack Number Starting I/O Group 0 PLC3, PLC5, PLC5/250 Example 17 16 15 14 13 12 11 10 I/O Bit I/O Group Number I/O Rack Number 7 6 111 Reserved 010 Reserved 011 11 Reserved 10 5 4 3 2 1 0 Input Image Block Data Output Image Block Data 10838I Figure 4.5 Input/Output Image Table Usage Example for One Starting I/O Group for 8 Input/8 Output Modules (cat. no. 17918AC, 8BC, 8AR, 8BR) PLC2 Example Type of I/O 1 = Input 0 = Output I/O Rack Number 110 Starting I/O Group 0 1 1 0 00 PLC3, PLC5, PLC5/250 Example I I/O Bit I/O Group Number Reserved 1 0 00 Type of I/O I = Input O = Output I/O Rack Number 7 6 5 4 I/O Bit I/O Group Number 3 2 1 0 2 1 0 11Reserved 10 111 Input Image Block Data 010 011 Reserved 7 6 5 4 3 11 Reserved 10 Block Data Output Image 10838I 4-6 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Figure 4.6 I/O Image Table for One Assigned Rack Number with 32point Modules 179116AC 17910B32 179132B0 179132A0 0 1 2 3 4 5 6 7 Input Image 8 7 10 7 15 17 0 SLC 0 PLC Reserved Reserved Reserved 1 I/O Rack Output Image 8 7 10 7 15 17 Reserved Reserved Reserved Reserved 0 1 2 3 4 5 6 7 0 SLC 0 PLC Reserved Figure 4.7 Input/Output Image Table Usage Example for One Starting I/O Group for 32 Output Modules (cat. no. 17910A32, 0B32) PLC2 Example 0 1 0 00 Type of I/O 1 = Input 0 = Output I/O Rack Number 110 Starting I/O Group 0 111 PLC3, PLC5, PLC5/250 Example O 1 0 00 Type of I/O I = Input O = Output I/O Bit I/O Group Number I/O Bit I/O Group Number I/O Rack Number Reserved 11 10 Reserved Input Image Block Data 010 17 16 15 14 13 12 11 10 7 6 5 4 3 2 1 0 011 17 16 15 14 13 12 11 10 10 7 6 5 4 3 2 1 0 Output Image Block Data 10838I 4-7 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Figure 4.8 Input/Output Image Table Usage Example for One Starting I/O Group with 32 Input Modules (cat. no. 179132A0, 32B0) PLC2 Example PLC3, PLC5, PLC5/250 Example I 1 1 0 00 Type of I/O 1 = Input 0 = Output I/O Bit I/O Group Number I/O Rack Number 110 Starting 111 I/O Group 010 0 1 0 00 Type of I/O I = Input O = Output I/O Bit I/O Group Number I/O Rack Number 17 16 15 14 13 12 11 10 7 6 5 4 3 2 1 0 17 16 15 14 13 12 11 10 7 6 5 4 3 2 1 0 Input Image Block Data Reserved Output Image 11 Reserved 10 011 Block Data 10838I Figure 4.9 Input/Output Image Table Usage Example for One Starting I/O Group for 16 Input/16 Output Modules (cat. no. 179116AC, 16BC) PLC2 Example 1 1 0 00 Type of I/O 1 = Input 0 = Output 110 1 0 00 Type of I/O I = Input O = Output I/O Bit I/O Group Number I/O Rack Number Starting I/O Group 0 PLC3, PLC5, PLC5/250 Example I 17 16 15 14 13 12 11 10 I/O Bit I/O Group Number I/O Rack Number 7 6 5 6 5 4 3 2 1 0 2 1 0 Input Image 11Reserved 10 111 Block Data 010 17 16 15 14 13 12 11 10 7 4 3 Output Image 11 Reserved 10 011 Block Data 10838I Figure 4.10 Input/Output Image Table Usage Example for One Starting I/O Group for 24 Input/8 Output Modules (cat. no. 179124A8, 24B8, 24AR, 24BR) PLC2 Example PLC3, PLC5, PLC5/250 Example 1 1 0 00 Type of I/O 1 = Input 0 = Output I/O Bit I/O Group Number I/O Rack Number 110 Starting I/O Group 0 111 17 16 15 14 13 Reserved I 1 0 00 Type of I/O I = Input O = Output 12 I/O Bit I/O Group Number I/O Rack Number 11 10 7 6 5 4 3 2 1 0 11 10 7 6 5 4 3 2 1 0 2 1 0 Input Image Block Data 010 011 Reserved 7 6 5 4 3 11 Reserved 10 Output Image Block Data 4-8 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com 10838I Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Using Complementary I/O PLC-2 and PLC-5 family processors support a complementary I/O configuration. Complementary I/O can allow you to maximize memory usage without increasing memory size. Refer to the user’s manual for your processor to see if it supports this type of configuration. You configure complementary I/O by duplicating an I/O rack number of one I/O chassis (primary) in another I/O chassis (complementary), I/O group for I/O group. The I/O modules in the complementary chassis perform the opposite function of the corresponding modules in the primary chassis. Important: Series A block I/O modules do not support complementary I/O. If using complementary I/O, use series B modules. When using I/O racks in a complementary configuration, the block I/O must be paired with a device which occupies 1/4 rack of I/O space (i.e. primary and complementary must be the same logical rack size). Note: The 1747-SN series A is not capable of supporting complementary I/O. Figure 4.11 Processor Data Table Use with Complementary I/O 16 or 32point Input Block I/O 16 or 32point Input Block I/O 16 or 32point Input Block I/O To Programmable Controller or I/O Scanner Module Input Block and Output Block on each pair have the same logical address. 16 or 32point Input Block I/O 16 or 32point Output Block I/O 16 or 32point Output Block I/O 16 or 32point Output Block I/O 16 or 32point Output Block I/O Install terminating resistor on last block. 1 I/O Rack with Complementary I/O 10833I 4-9 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Remote rack numbers which can have a complementary rack are rack numbers 01 thru 07 only (Table 4.H). When configured as complementary I/O: PLC-2 can scan racks 01–07 PLC-5/11 can scan rack 03 PLC-5/20, PLC-5/30, PLC-5/40, PLC-5/60 can scan racks 01–07 Table 4.H PLC-2 and PLC-5 With Complementary I/O SW1 Switch Position PLC-2 Rack Number PLC-5 Rack Number 8 7 6 5 4 3 Rack 1 Not Valid 0 0 1 0 0 0 Rack 2 Rack 1 0 0 1 0 0 1 Rack 3 Rack 2 0 0 1 0 1 0 Rack 4 Rack 3 0 0 1 0 1 1 Rack 5 Rack 4 0 0 1 1 0 0 Rack 6 Rack 5 0 0 1 1 0 1 Rack 7 Rack 6 0 0 1 1 1 0 Rack 7 0 0 1 1 1 1 Figure 4.12 I/O Image Table for One Assigned Rack Number with Series B 16point Modules using Complementary I/O 1/4 Rack 1/4 Rack 1/4 Rack 1/4 Rack 17910B16 179116A0 179116B0 179116A0 17910B16 179116A0 17910B16 179116A0 0 1 2 3 4 5 6 7 15 17 Input Image 8 7 10 7 0 SLC 0 PLC Reserved Reserved Reserved Reserved 1 I/O Rack 15 17 0 1 2 3 4 5 6 7 Output Image 8 7 10 7 Reserved Reserved Reserved Reserved 4-10 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com 0 SLC 0 PLC Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Figure 4.13 Input/Output Image Table Usage Example for One I/O Group for Series B 16point Output Modules (cat. no. 17910A16, 0B16) Complemented by Series B 16point Input Modules (cat. no. 179116A0, 16B0) PLC2 Example PLC5 Family Example 0 1 0 00 Type of I/O 1 = Input 0 = Output I/O Bit I/O Group Number I/O Rack Number Starting I/O Group 0 O 1 0 00 Type of I/O I = Input O = Output I/O Bit I/O Group Number I/O Rack Number 110 17 16 15 14 13 12 7 6 5 4 3 2 1 111 17 16 15 14 13 12 11 10 10 7 6 5 4 3 2 1 0 11 10 0 Input Image (used by Input Module) Block Data 010 17 16 15 14 13 12 011 11 10 7 6 5 4 3 2 1 0 16 15 14 13 12 11 10 10 7 6 5 4 3 2 1 0 Output Image (used by output module) Block Data 10838I Figure 4.14 I/O Image Table for One Assigned Rack Number with Series B 32point Modules using Complementary I/O Input Image 1/4 Rack 1/4 Rack 1/4 Rack 17910B32 179132B0 17910B32 179132A0 17910B32 179132B0 17910B32 179132A0 0 1 2 3 4 5 6 7 15 17 1 I/O Rack 1/4 Rack 0 1 2 3 4 5 6 7 15 17 8 7 10 7 Output Image 8 7 10 7 0 SLC 0 PLC 0 SLC 0 PLC 4-11 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Figure 4.15 Input/Output Image Table Usage Example for One I/O Group for Series B 32point Output Modules (cat. no. 17910A32, 0B32) Complemented by Series B 32point Input Modules (cat. no. 179132A0, 32B0) PLC2 Example Type of I/O 1 = Input 0 = Output I/O Rack Number Starting I/O Group 0 PLC5 Family Example O 1 0 00 0 1 0 00 Type of I/O I = Input O = Output I/O Rack Number I/O Bit I/O Group Number I/O Bit I/O Group Number 110 17 16 15 14 13 12 11 10 7 6 5 4 3 2 1 0 111 11 10 10 7 17 16 15 14 13 12 11 6 5 4 3 2 1 0 010 17 16 15 14 13 12 11 10 7 6 5 4 3 2 1 0 011 17 16 15 14 13 12 11 11 10 10 7 6 5 4 3 2 1 0 Input Image (used by Input Module) Block Data Output Image (used by output module) Block Data 10838I Figure 4.16 I/O Image Table for One Assigned Rack Number with Series B 32point Modules and Series B 16point Modules Complemented by each other Input Image 1/4 Rack 1/4 Rack 1/4 Rack 17910B16 179132B0 17910B32 179116A0 17910B32 179116B0 17910B16 179132A0 0 1 2 3 4 5 6 7 15 17 0 1 2 3 4 5 6 7 0 SLC 0 PLC Reserved Reserved 1 I/O Rack 1/4 Rack 8 7 10 7 15 17 Output Image 8 7 10 7 Reserved Reserved 4-12 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com 0 SLC 0 PLC Chapter 4 Configuring Your Block I/O for PLC Family Programmable Controllers Figure 4.17 Input/Output Image Table Usage Example for One I/O Group for Series B 32point Output Modules (cat. no. 17910A32, 0B32) Complemented by Series B 16point Input Modules (cat. no. 179116A0, 16B0) PLC2 Example Type of I/O 1 = Input 0 = Output I/O Rack Number Starting I/O Group 0 PLC5 Family Example O 1 0 00 0 1 0 00 I/O Bit I/O Group Number Type of I/O I = Input O = Output I/O Rack Number I/O Bit I/O Group Number 110 17 16 15 14 13 12 11 10 6 5 4 3 2 1 0 111 Reserved 11 10 10 7 6 17 16 15 14 13 12 11 5 4 3 2 1 0 010 17 16 15 14 13 12 11 10 7 6 5 4 3 2 1 0 011 17 16 15 14 13 12 11 11 10 10 7 6 5 4 3 2 1 0 7 Input Image (used by Input Module) Block Data Output Image (used by output module) Block Data 10838I 4-13 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 5 Troubleshooting Chapter Objectives In this chapter you will learn about the indicators on the block I/O module, and how to use them to troubleshoot the unit. Indicators Each block I/O module has indicators (Figure 5.1) which provide indication of module status. Each module has the following: Indicator Color Quantity Description COMM Green 1 Indicates whether communication is occurring between processor or scanner and the block module STATUS Red 1 Indicates hardware or software error, and if communication has failed I/O Status Red 16 Reflect the state of the individual inputs and/or outputs (on or off) Figure 5.1 shows the location of the indicators. Refer to Table 5.A for status indications reported by the indicators. Figure 5.1 Indicators on the Block I/O Module Communication Indicator (green) Communication Indicator (green) COMM COMM 32 Input/Output Status Indicators (red) 16 Input/Output Status Indicators (red) STATUS STATUS Fault Status Indicator (red) Fault Status Indicator (red) 16point Block 32point Block 12404-I 5-1 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Chapter 5 Troubleshooting Table 5.A Troubleshooting Chart Indication Probable Cause Corrective Action Green COMM indicator on Red STATUS indicator off I/O status indicator on/off Normal operation None required Red STATUS indicator on Block failed selftest, or a major fault is detected. Cycle power to the block. If problem persists, replace the block. Red STATUS indicator flashing Green COMM indicator off Communication failure - RIO cable off, 100ms between valid frames, 20ms idle time exceeded. Improper processor or scanner switch settings. Check remote I/O cable connections, verify scanner or processor switch settings. No communication with processor, scanner etc. Check that power is applied to block. Make sure that proper number of blocks are configured. Check remote I/O link for duplicate address. Reset command (or output disable bit for SLC) has been issued by processor or scanner. Check program. Correct as necessary. Check terminator, resistors and cable wiring. SLC or programmable controller in program mode. Place in run mode. Processor restart lockout is selected and a fault has occurred. (Communication to block is established.) Cycle power to block. Green COMM indicator off Green COMM indicator flashing COMM and STATUS indicators alternately flashing 5-2 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ 6SHFLILFDWLRQV )RU 6SHFLILFDWLRQV IRU 5HIHU WR $% 3DJH $ $% 3DJH $ $&% 3DJH $ $5% 3DJH $ $% 3DJH $ $% 3DJH $ $&% 3DJH $ $% 3DJH $ $5% 3DJH $ %% 3DJH $ %% 3DJH $ %&% 3DJH $ %5% 3DJH $ %% 3DJH $ %% 3DJH $ %&% 3DJH $ %% 3DJH $ %5% 3DJH $ $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $ 6HULHV % 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN JURXSV RI 1RPLQDO ,QSXW &XUUHQW P$ 1RPLQDO ,QSXW 9ROWDJH 9 DF 2QïVWDWH 9ROWDJH 5DQJH ï9 DF ï+] 2IIVWDWH 9ROWDJH 0D[LPXP 9 2QVWDWH &XUUHQW 0LQLPXP P$ # 9 +] 2IIVWDWH &XUUHQW 0LQLPXP P$ +] ,QSXW ,PSHGDQFH 0D[LPXP . RKPV # +] ,QSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV PV PD[LPXP DOORZV IRU F\FOH GURSRXW *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU ,QWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 DF ï+] P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH PP VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $ 6HULHV % 6SHFLILFDWLRQV 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN JURXSV RI 2XWSXW 9ROWDJH 5DQJH ï9 DF ï+] 2XWSXW &XUUHQW 5DWLQJ 9HUWLFDO 0WJ +RUL]RQWDO 0WJ P$ # R& P$ # R& P$ # R& P$ # R& 6XUJH &XUUHQW $ IRU PV HDFK UHSHDWDEOH HYHU\ VHF 0LQLPXP 2QVWDWH &XUUHQW P$ SHU RXWSXW 0D[LPXP 2QVWDWH 9ROWDJH 'URS 9 SHDN # P$ 2IIVWDWH /HDNDJH &XUUHQW PD[LPXP P$ 2XWSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV # +] PV # +] PV # +] PV # +] *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU ,QWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 DF ï+] P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH PP VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $& 6HULHV % 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN JURXS RI 1RPLQDO ,QSXW &XUUHQW P$ 1RPLQDO ,QSXW 9ROWDJH 9 DF 2QVWDWH 9ROWDJH 5DQJH ï9 DF ï+] 2IIVWDWH 9ROWDJH 0D[LPXP 9 2QVWDWH &XUUHQW 0LQLPXP P$ # 9 +] 2IIVWDWH &XUUHQW 0LQLPXP P$ +] ,QSXW ,PSHGDQFH 0D[LPXP . RKPV # +] ,QSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV PV PD[LPXP DOORZV IRU F\FOH GURSRXW 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN JURXS RI 2XWSXW 9ROWDJH 5DQJH ï9 DF 2XWSXW &XUUHQW 5DWLQJ 9HUWLFDO 0WJ +RUL]RQWDO 0WJ P$ # R& P$ # R& P$ # R& P$ # R& 6XUJH &XUUHQW $ IRU PV HDFK UHSHDWDEOH HYHU\ VHF 0LQLPXP 2QVWDWH &XUUHQW P$ SHU RXWSXW 0D[LPXP 2QVWDWH 9ROWDJH 'URS 9 SHDN # P$ 2IIVWDWH /HDNDJH &XUUHQW PD[LPXP P$ 2XWSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV # +] PV # +] PV # +] PV # +] *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU ,QWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 DF ï+] P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH PP VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $5 6HULHV % 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN JURXS RI 1RPLQDO ,QSXW &XUUHQW P$ 1RPLQDO ,QSXW 9ROWDJH 9 DF 2QVWDWH 9ROWDJH 5DQJH ï9 DF ï+] 2IIVWDWH 9ROWDJH 0D[LPXP 9 2QVWDWH &XUUHQW 0LQLPXP 0D[LPXP P$ # 9 +] P$ # 9 +] 2IIVWDWH &XUUHQW 0LQLPXP P$ +] ,QSXW ,PSHGDQFH 0D[LPXP . RKPV # +] ,QSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV PV PD[LPXP DOORZV IRU F\FOH GURSRXW 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN JURXS RI )RUP $ QRUPDOO\ RSHQ HOHFWURPHFKDQLFDO UHOD\V 2XWSXW 9ROWDJH 5DQJH ORDG GHSHQGHQW ï9 DF # $ UHVLVWLYH PD[LPXP ï9 GF # $ UHVLVWLYH PD[LPXP 9 GF # $ UHVLVWLYH PD[LPXP 2XWSXW &XUUHQW 5DWLQJ DW UDWHG SRZHU 5HVLVWLYH ï 3) FRV q $ # ï9 DF $ # ï9 GF $ # 9 GF ,QGXFWLYH ï 3) FRV q $ # ï9 DF $ # ï9 GF /5 PV $ # 9 GF /5 PV 6XUJH &XUUHQW DW UDWHG SRZHU ZLWK LQGXFWLYH ORDGV $ # ï9 DF FRV q $ # ï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rtisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $5 6HULHV % 6SHFLILFDWLRQV *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU ,QWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 DF ï+] P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF %HWZHHQ RSHQ FRQWDFWV 9 DF 9 DF 9 DF 9 DF LQLWLDO 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï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rtisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV % 6HULHV % 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN ï JURXSV RI 2QVWDWH 9ROWDJH 5DQJH ï9 GF 2QVWDWH &XUUHQW 0D[LPXP 0LQLPXP P$ # 9 P$ # 9 2IIVWDWH 9ROWDJH 0D[LPXP 9 GF 2IIVWDWH &XUUHQW 0LQLPXP P$ ,QSXW ,PSHGDQFH 0D[LPXP . RKPV ,QSXW 6LJQDO 'HOD\ )DVW 6ORZ PV RQ PV RII PD[LPXP PV RQ PV RII PD[LPXP *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH ï9 GF &XUUHQW P$ 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH PP VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV % 6HULHV % 6SHFLILFDWLRQV 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN ï JURXSV RI 2XWSXW 9ROWDJH 5DQJH ï9 GF 2XWSXW &XUUHQW 5DWLQJ 9HUWLFDO 0WJ +RUL]RQWDO 0WJ P$ # R& $ # R& P$ # R& P$ # R& 6XUJH &XUUHQW $ IRU PV HDFK UHSHDWDEOH HYHU\ VHF 0LQLPXP 2QVWDWH &XUUHQW P$ SHU RXWSXW 0D[LPXP 2QVWDWH 9ROWDJH 'URS 9 # UDWHG FXUUHQW 2IIVWDWH /HDNDJH &XUUHQW PD[LPXP P$ 2XWSXW 6LJQDO 'HOD\ PV RQ PV RII PD[LPXP *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 GF P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH PP VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV %& 6HULHV % 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN ï JURXS RI 2QVWDWH 9ROWDJH 5DQJH ï9 GF 2QVWDWH &XUUHQW 0D[LPXP 0LQLPXP P$ # 9 P$ # 9 2IIVWDWH 9ROWDJH 0D[LPXP 9 GF 2IIVWDWH &XUUHQW 0LQLPXP P$ ,QSXW ,PSHGDQFH 0D[LPXP . RKPV ,QSXW 6LJQDO 'HOD\ )DVW 6ORZ PV RQ PV RII PD[LPXP PV RQ PV RII PD[LPXP 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN ï JURXS RI 2XWSXW 9ROWDJH 5DQJH ï9 GF 2XWSXW &XUUHQW 5DWLQJ 9HUWLFDO 0WJ +RUL]RQWDO 0WJ P$ # R& $ # R& P$ # R& P$ # R& 6XUJH &XUUHQW $ IRU PV HDFK UHSHDWDEOH HYHU\ VHF 0LQLPXP 2QVWDWH &XUUHQW P$ SHU RXWSXW 0D[LPXP 2QVWDWH 9ROWDJH 'URS 9 # UDWHG FXUUHQW 2IIVWDWH /HDNDJH &XUUHQW PD[LPXP P$ 2XWSXW 6LJQDO 'HOD\ PV RQ PV RII PD[LPXP *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 GF P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH PP VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV %5 6HULHV % 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN ï JURXS RI 2QVWDWH 9ROWDJH 5DQJH ï9 GF 2QVWDWH &XUUHQW 0D[LPXP 0LQLPXP P$ # 9 P$ # 9 2IIVWDWH 9ROWDJH 0D[LPXP 9 GF 2IIVWDWH &XUUHQW 0LQLPXP P$ ,QSXW ,PSHGDQFH 0D[LPXP . RKPV ,QSXW 6LJQDO 'HOD\ )DVW 6ORZ PV RQ PV RII PD[LPXP PV RQ PV RII PD[LPXP 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN JURXS RI )RUP $ QRUPDOO\ RSHQ HOHFWURPHFKDQLFDO UHOD\V 2XWSXW 9ROWDJH 5DQJH ORDG GHSHQGHQW ï9 DF # $ UHVLVWLYH PD[LPXP ï9 GF # $ UHVLVWLYH PD[LPXP 9 GF # $ UHVLVWLYH PD[LPXP 2XWSXW &XUUHQW 5DWLQJ DW UDWHG SRZHU 5HVLVWLYH ï 3) FRV q $ # ï9 DF $ # ï9 GF $ # 9 GF ,QGXFWLYH ï 3) FRV q $ # ï9 DF $ # ï9 GF /5 PV $ # 9 GF /5 PV 6XUJH &XUUHQW DW UDWHG SRZHU ZLWK LQGXFWLYH ORDGV $ # ï9 DF FRV q $ # ï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rtisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV %5 6HULHV % 6SHFLILFDWLRQV *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 GF P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï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rtisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $ 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN JURXSV RI 1RPLQDO ,QSXW &XUUHQW P$ 1RPLQDO ,QSXW 9ROWDJH 9 DF 2QïVWDWH 9ROWDJH 5DQJH ï9 DF ï+] 2IIVWDWH 9ROWDJH 0D[LPXP 9 2QVWDWH &XUUHQW 0LQLPXP 0D[LPXP P$ # 9 +] P$ # 9 +] 2IIVWDWH &XUUHQW 0LQLPXP P$ +] ,QSXW ,PSHGDQFH 0D[LPXP . RKPV # +] ,QSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV PV PD[LPXP DOORZV IRU F\FOH GURSRXW *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 DF ï+] P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $ 6SHFLILFDWLRQV 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN JURXSV RI 2XWSXW 9ROWDJH 5DQJH ï9 DF ï+] 2XWSXW &XUUHQW 5DWLQJ 9HUWLFDO 0WJ +RUL]RQWDO 0WJ P$ # R& P$ # R& P$ # R& P$ # R& 6XUJH &XUUHQW $ IRU PV HDFK UHSHDWDEOH HYHU\ VHF 0LQLPXP 2QVWDWH &XUUHQW P$ SHU RXWSXW 0D[LPXP 2QVWDWH 9ROWDJH 'URS 9 SHDN # P$ 2IIVWDWH /HDNDJH &XUUHQW PD[LPXP P$ 2XWSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV # +] PV # +] PV # +] PV # +] *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 DF ï+] P$ # 9 DF + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $& 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN JURXSV RI 1RPLQDO ,QSXW &XUUHQW P$ 1RPLQDO ,QSXW 9ROWDJH 9 DF 2QVWDWH 9ROWDJH 5DQJH ï9 DF ï+] 2IIVWDWH 9ROWDJH 0D[LPXP 9 2QVWDWH &XUUHQW 0LQLPXP 0D[LPXP P$ # 9 +] P$ # 9 +] 2IIVWDWH &XUUHQW 0LQLPXP P$ +] ,QSXW ,PSHGDQFH 0D[LPXP . RKPV # +] ,QSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV PV PD[LPXP DOORZV IRU F\FOH GURSRXW 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN JURXSV RI 2XWSXW 9ROWDJH 5DQJH ï9 DF 2XWSXW &XUUHQW 5DWLQJ 9HUWLFDO 0WJ +RUL]RQWDO 0WJ P$ # R& P$ # R& P$ # R& P$ # R& 6XUJH &XUUHQW $ IRU PV HDFK UHSHDWDEOH HYHU\ VHF 0LQLPXP 2QVWDWH &XUUHQW P$ SHU RXWSXW 0D[LPXP 2QVWDWH 9ROWDJH 'URS 9 SHDN # P$ 2IIVWDWH /HDNDJH &XUUHQW PD[LPXP P$ 2XWSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV # +] PV # +] PV # +] PV # +] *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 DF ï+] P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ 0D[LPXP :DWWV 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $ 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN JURXSV RI 1RPLQDO ,QSXW &XUUHQW P$ 1RPLQDO ,QSXW 9ROWDJH 9 DF 2QVWDWH 9ROWDJH 5DQJH ï9 DF ï+] 2IIVWDWH 9ROWDJH 0D[LPXP 9 2QVWDWH &XUUHQW 0LQLPXP 0D[LPXP P$ # 9 +] P$ # 9 +] 2IIVWDWH &XUUHQW 0LQLPXP P$ +] ,QSXW ,PSHGDQFH 0D[LPXP . RKPV # +] ,QSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV PV PD[LPXP DOORZV IRU F\FOH GURSRXW 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN JURXS RI 2XWSXW 9ROWDJH 5DQJH ï9 DF 2XWSXW &XUUHQW 5DWLQJ 9HUWLFDO 0WJ +RUL]RQWDO 0WJ P$ # R& P$ # R& P$ # R& P$ # R& 6XUJH &XUUHQW $ IRU PV HDFK UHSHDWDEOH HYHU\ VHF 0LQLPXP 2QVWDWH &XUUHQW P$ SHU RXWSXW 0D[LPXP 2QVWDWH 9ROWDJH 'URS 9 SHDN # P$ 2IIVWDWH /HDNDJH &XUUHQW PD[LPXP P$ 2XWSXW 6LJQDO 'HOD\ PV # +] PV # +] PV # +] PV # +] 2II WR RQ 2Q WR RII *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 DF ï+] P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $5 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN JURXSV RI 1RPLQDO ,QSXW &XUUHQW P$ 1RPLQDO ,QSXW 9ROWDJH 9 DF 2QVWDWH 9ROWDJH 5DQJH ï9 DF ï+] 2IIVWDWH 9ROWDJH 0D[LPXP 9 2QVWDWH &XUUHQW 0LQLPXP 0D[LPXP P$ # 9 +] P$ # 9 +] 2IIVWDWH &XUUHQW 0LQLPXP P$ +] ,QSXW ,PSHGDQFH 0D[LPXP . RKPV # +] ,QSXW 6LJQDO 'HOD\ 2II WR RQ 2Q WR RII PV PV PD[LPXP DOORZV IRU F\FOH GURSRXW 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN JURXS RI )RUP $ QRUPDOO\ RSHQ HOHFWURPHFKDQLFDO UHOD\V 2XWSXW 9ROWDJH 5DQJH ORDG GHSHQGHQW ï9 DF # $ UHVLVWLYH PD[LPXP ï9 GF # $ UHVLVWLYH PD[LPXP 9 GF # $ UHVLVWLYH PD[LPXP 2XWSXW &XUUHQW 5DWLQJ DW UDWHG SRZHU 5HVLVWLYH ï 3) FRV q $ # ï9 DF $ # ï9 GF $ # 9 GF ,QGXFWLYH ï 3) FRV q $ # ï9 DF $ # ï9 GF /5 PV $ # 9 GF /5 PV 6XUJH &XUUHQW DW UDWHG SRZHU ZLWK LQGXFWLYH ORDGV $ # ï9 DF FRV q $ # ï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rtisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV $5 6SHFLILFDWLRQV *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 DF ï+] P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF %HWZHHQ RSHQ FRQWDFWV 9 DF 9 DF 9 DF 9 DF LQLWLDO 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï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rtisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV % 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN ï JURXSV RI 2QVWDWH 9ROWDJH 5DQJH ï9 GF 2QVWDWH &XUUHQW 0D[LPXP 0LQLPXP P$ # 9 P$ # 9 2IIVWDWH 9ROWDJH 0D[LPXP 9 GF 2IIVWDWH &XUUHQW 0LQLPXP P$ ,QSXW ,PSHGDQFH 0D[LPXP . RKPV ,QSXW 6LJQDO 'HOD\ )DVW 6ORZ PV RQ PV RII PD[LPXP PV RQ PV RII PD[LPXP *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 GF P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH PP VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV % 6SHFLILFDWLRQV 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN ï JURXSV RI 2XWSXW 9ROWDJH 5DQJH ï9 GF 2XWSXW &XUUHQW 5DWLQJ 9HUWLFDO 0WJ +RUL]RQWDO 0WJ P$ # R& $ # R& P$ # R& P$ # R& 6XUJH &XUUHQW $ IRU PV HDFK UHSHDWDEOH HYHU\ VHF 0LQLPXP 2QVWDWH &XUUHQW P$ SHU RXWSXW 0D[LPXP 2QVWDWH 9ROWDJH 'URS 9 # UDWHG FXUUHQW 2IIVWDWH /HDNDJH &XUUHQW PD[LPXP P$ 2XWSXW 6LJQDO 'HOD\ PV RQ PV RII PD[LPXP *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 GF P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH PP VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV %& 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN ï JURXSV RI 2QVWDWH 9ROWDJH 5DQJH ï9 GF 2QVWDWH &XUUHQW 0D[LPXP 0LQLPXP P$ # 9 P$ # 9 2IIVWDWH 9ROWDJH 0D[LPXP 9 GF 2IIVWDWH &XUUHQW 0LQLPXP P$ ,QSXW ,PSHGDQFH 0D[LPXP . RKPV ,QSXW 6LJQDO 'HOD\ )DVW 6ORZ PV RQ PV RII PD[LPXP PV RQ PV RII PD[LPXP 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN ï JURXSV RI 2XWSXW 9ROWDJH 5DQJH ï9 GF 2XWSXW &XUUHQW 5DWLQJ 9HUWLFDO 0WJ +RUL]RQWDO 0WJ P$ # R& $ # R& P$ # R& P$ # R& 6XUJH &XUUHQW $ IRU PV HDFK UHSHDWDEOH HYHU\ VHF 0LQLPXP 2QVWDWH &XUUHQW P$ SHU RXWSXW 0D[LPXP 2QVWDWH 9ROWDJH 'URS 9 # UDWHG FXUUHQW 2IIVWDWH /HDNDJH &XUUHQW PD[LPXP P$ 2XWSXW 6LJQDO 'HOD\ PV RQ PV RII PD[LPXP 6SHFLILFDWLRQV FRQWLQXHG RQ QH[W SDJH *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 GF P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH PP VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV % 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN ï JURXSV RI 2QVWDWH 9ROWDJH 5DQJH ï9 GF 2QVWDWH &XUUHQW 0D[LPXP 0LQLPXP P$ # 9 P$ # 9 2IIVWDWH 9ROWDJH 0D[LPXP 9 GF 2IIVWDWH &XUUHQW 0LQLPXP P$ ,QSXW ,PSHGDQFH 0D[LPXP . RKPV ,QSXW 6LJQDO 'HOD\ )DVW 6ORZ PV RQ PV RII PD[LPXP PV RQ PV RII PD[LPXP 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN ï JURXS RI 2XWSXW 9ROWDJH 5DQJH ï9 GF 2XWSXW &XUUHQW 5DWLQJ 0WJ 9HUWLFDO 0WJ +RUL]RQWDO P$ # R& $ # R& P$ # R& P$ # R& 6XUJH &XUUHQW $ IRU PV HDFK UHSHDWDEOH HYHU\ VHF 0LQLPXP 2QVWDWH &XUUHQW P$ SHU RXWSXW 0D[LPXP 2QVWDWH 9ROWDJH 'URS 9 # UDWHG FXUUHQW 2IIVWDWH /HDNDJH &XUUHQW PD[LPXP P$ 2XWSXW 6LJQDO 'HOD\ PV RQ PV RII PD[LPXP *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 GF P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï WR R) WR QRQFRQGHQVLQJ &RQGXFWRUV :LUH 6L]H &DWHJRU\ JDXJH PP VWUDQGHG PD[LPXP LQFK LQVXODWLRQ PD[LPXP <RX XVH WKLV FRQGXFWRU FDWHJRU\ LQIRUPDWLRQ IRU SODQQLQJ FRQGXFWRU URXWLQJ DV GHVFULEHG LQ WKH V\VWHP OHYHO LQVWDOODWLRQ PDQXDO $ Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV %5 6SHFLILFDWLRQV ,QSXW 6SHFLILFDWLRQV ,QSXWV SHU %ORFN ï JURXSV RI 2QVWDWH 9ROWDJH 5DQJH ï9 GF 2QVWDWH &XUUHQW 0D[LPXP 0LQLPXP P$ # 9 P$ # 9 2IIVWDWH 9ROWDJH 0D[LPXP 9 GF 2IIVWDWH &XUUHQW 0LQLPXP P$ ,QSXW ,PSHGDQFH 0D[LPXP . RKPV ,QSXW 6LJQDO 'HOD\ )DVW 6ORZ PV RQ PV RII PD[LPXP PV RQ PV RII PD[LPXP 2XWSXW 6SHFLILFDWLRQV 2XWSXWV SHU %ORFN JURXS RI )RUP $ QRUPDOO\ RSHQ HOHFWURPHFKDQLFDO UHOD\V 2XWSXW 9ROWDJH 5DQJH ORDG GHSHQGHQW ï9 DF # $ UHVLVWLYH PD[LPXP ï9 GF # $ UHVLVWLYH PD[LPXP 9 GF # $ UHVLVWLYH PD[LPXP 2XWSXW &XUUHQW 5DWLQJ DW UDWHG SRZHU 5HVLVWLYH ï 3) FRV q $ # ï9 DF $ # ï9 GF $ # 9 GF ,QGXFWLYH ï 3) FRV q $ # ï9 DF $ # ï9 GF /5 PV $ # 9 GF /5 PV 6XUJH &XUUHQW DW UDWHG SRZHU ZLWK LQGXFWLYH ORDGV $ # ï9 DF FRV q $ # ï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rtisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com $SSHQGL[ $ 6SHFLILFDWLRQV %5 6SHFLILFDWLRQV *HQHUDO 6SHFLILFDWLRQV ([WHUQDO 3RZHU LQWHUQDOO\ SURWHFWHG QR H[WHUQDO IXVH UHTXLUHG 9ROWDJH &XUUHQW 'LPHQVLRQV ,QFKHV 0LOOLPHWHUV ï9 GF P$ + ; : ; ' + ; : ; ' ,VRODWLRQ 3RZHU VXSSO\ WR 5,2 ,2 *URXSWR*URXS ,2 *URXSWR/RJLF 9 DF 9 DF 9 DF 3RZHU 'LVVLSDWLRQ :DWWV 0D[LPXP 7KHUPDO 'LVVLSDWLRQ 0D[LPXP %78KU (QYLURQPHQWDO &RQGLWLRQV 2SHUDWLRQDO 7HPSHUDWXUH 6WRUDJH 7HPSHUDWXUH 5HODWLYH +XPLGLW\ WR R& WR R) ï WR R& ï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rtisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Index Symbols **Empty**, 336 B block compatibility, 12 16-point modules, 411 32-point modules, 412 one assigned rack number 16-point and 32-point modules, 412 16-point modules, 45 32-point modules, 47, 411 complementary I/O, 410 indicators, location, 51 C compatibility, 12 ac input modules, 21 ac output modules, 21 dc input modules, 22 dc output modules, 21 extended node numbers, 338 other Allen-Bradley products, 22 input compatibility, 21 input devices, typical, 21 L LED indicators, 51 M complementary I/O, with 1/2-slot addressing, 49 mounting, DIN rail, 34 configuration switches, 41 mounting dimensions, 33 connecting block I/O, in a PLC system, 13 D description, P2, 11 O on-state voltage and currents, 23 output circuits, dc, 27 output compatibility, 25 E extended node capability, 337 F features, 12 fusing output ratings and surge currents, 29 recommended fuses, 28 I image table usage, 45 16 input/16 output modules, 48 16-point input modules, 46 16-point output modules, 46 24 input/8 output modules, 48 32-point input modules, 48 32-point output modules, 47 8 input/8 output modules, 46 complementary I/O 16 and 32-point modules, 413 output currents, ac, 25 R related publications, P2 remote I/O link, selecting speed, 338 remote I/O link connector, 13 remote I/O link wiring, 336 S scanning, 13 schematics ac output, 26 dc output, 27 simplified, 24 series connections, SLC, 337 simplified schematics, 24 specifications, A1 status indicators, 13 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com I–2 Index surge suppression, 334 switch settings, 42 complementary I/O, 410 complementary rack, 44 primary rack, 43 T terminal block pin numbering, 35 removal, 34 termination resistor, 334 throughput requirements, 338 troubleshooting chart, 52 Types of block I/O, 11 1791-0A32, 1791-0B16, 1791-0B32, 1791-16A0, 1791-16AC, 1791-16B0, 1791-16BC, 1791-24A8, 1791-24AR, 1791-24B8, 1791-24BR, 1791-32A0, 1791-32B0, 1791-8AC, 1791-8AR, 1791-8BC, 1791-8BR, 312 321 326 36 314 320 328 316 318 330 332 310 324 38 39 322 323 types of block I/O, P2 W wiring connections, 34 1791-0A16, 37 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com AllenBradley has been helping its customers improve productivity and quality for 90 years. AB designs, manufactures and supports a broad range of control and automation products worldwide. They include logic processors, power and motion control devices, manmachine interfaces and sensors. AllenBradley is a subsidiary of Rockwell International, one of the world's leading technology companies. With major offices worldwide. Algeria • Argentina • Australia • Austria • Bahrain • Belgium • Brazil • Bulgaria • Canada • Chile • China, PRC • Colombia • Costa Rica • Croatia • Cyprus • Czech Republic • Denmark • Ecuador • Egypt • El Salvador • Finland • France • Germany • Greece • Guatemala • Honduras • Hong Kong • Hungary • Iceland • India • Indonesia • Israel • Italy • Jamaica • Japan • Jordan • Korea • Kuwait • Lebanon • Malaysia • Mexico • New Zealand • Norway • Oman • Pakistan • Peru • Philippines • Poland • Portugal • Puerto Rico • Qatar • Romania • Russia-CIS • Saudi Arabia • Singapore • Slovakia • Slovenia • South Africa, Republic • Spain • Switzerland • Taiwan • Thailand • The Netherlands • Turkey • United Arab Emirates • United Kingdom • United States • Uruguay • Venezuela • Yugoslavia World Headquarters, AllenBradley, 1201 South Second Street, Milwaukee, WI 53204 USA, Tel: (1) 414 3822000 Fax: (1) 414 3824444 Publication 1791-6.5.3 - March 1994 Supersedes publication 17916.5.3 dated August 1993 PN 955117-24 Copyright 1994 AllenBradley Company, Inc. Printed in USA Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment • FAST SHIPPING AND DELIVERY • TENS OF THOUSANDS OF IN-STOCK ITEMS • EQUIPMENT DEMOS • HUNDREDS OF MANUFACTURERS SUPPORTED • LEASING/MONTHLY RENTALS • ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center WE BUY USED EQUIPMENT Sell your excess, underutilized, and idle used equipment We also offer credit for buy-backs and trade-ins www.artisantg.com/WeBuyEquipment InstraView REMOTE INSPECTION LOOKING FOR MORE INFORMATION? Visit us on the web at www.artisantg.com for more information on price quotations, drivers, technical specifications, manuals, and documentation SM Remotely inspect equipment before purchasing with our interactive website at www.instraview.com Contact us: (888) 88-SOURCE | [email protected] | www.artisantg.com ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Complete I/O Interface
- Compatible with PLC-2, PLC-3, PLC-5/250, PLC-5 and SLC
- Removable Terminal Strip
- Switch Assembly
- Status Indicators
- Asynchronous Data Transfer
Frequently asked questions
Refer to Table 3.A for acceptable combinations of processor and block I/O, including maximum capacity and network distance based on baud rate.
Connect the wiring to the removable terminal block, ensuring the lower row of screws is positioned towards the outside of the module. Refer to the wiring diagrams for specific pin numbers.
Output fusing is recommended. Refer to Table 2.B for recommended fuse types and ratings based on the circuit type (ac or dc).
Mount the blocks vertically with a minimum of 2” between blocks to ensure proper cooling air flow. Refer to Figure 3.1 for the mounting dimensions.
Visit www.artisantg.com for more information on price quotations, drivers, technical specifications, manuals, and documentation.