x Spies Hecker Plastic System

x Spies Hecker Plastic System
System
Data Sheet.
The Paint System
for plastic parts
Using this universal paint system, most plastic parts
found on motor vehicles can be easily refinished.
(Types of plastic: PP, PP/EPDM, ASB, SAN,PC, PPO,
PBTP, GRP, PA, PVC, R-TPU, PUR, PUR-RIM, PUR
soft, T.PO, UP-GF.)
This product is for professional painting of vehicles only.
13 V.1
VR Technical Data Sheet No.901.1(N/A) July. 2013
 2013 Axalta Coating Systems and all affiliates. All rights reserved.
The Paint System for plastic parts
Substrate
Primed Plastic
Substrate
Pretreatment:
Perform a solvent test to check if primer is reversible.
1. If the primer is reversible, then strip and treat as raw plastic.
2. If the primer is not reversible
a. Wash with soap and water, clean with Permaloid Silicone Remover
7010 Slow, Permahyd Silicone Remover 7085 or Permahyd Silicone
Remover 7096.Sand primer (with P500-800 dry or wet with P600-800).
Make sure to scuff all of the edges and hard to reach area with a gray
or gold scotch pad.
b. Re-clean with Permaloid Silicone Remover 7010 Slow, Permahyd
Silicone Remover 7085, Permahyd or Permahyd Silicone Remover
7096.
c. Use the appropriate surfacer and/or topcoat.
Substrate
Raw Plastic
Substrate
Pretreatment:
The substrate must be free from release agents.
Clean with Permahyd Plastic Cleaning Paste 7081 using hot water and a gray or gold
scuff pad.
Rinse thoroughly and bake for 15-30 minutes at a surface temperature of 140ºF.
Once the bumper has cooled, scrub once more with Permahyd Plastic Cleaning
Paste 7081 using hot water and a gray or gold scuff pad.
Rinse thoroughly and dry.
Now the appropriate primer/surfacer systems can be applied.
 2013 Axalta Coating Systems and all affiliates. All rights reserved.
The Paint System for plastic parts
Paint System
Primer:
To achieve good adhesion, plastic parts must be primed as soon as possible after they
have been thoroughly cleaned. The painter can choose between A or B as described
below.
For new or undamaged plastic:
A) Apply Permacron 1:1 Elastic Primer Surfacer 3300 (for application see VR
Data Sheet 310.1).Top coats can be applied wet on wet on top of this primer
surfacer.
For new, repaired or undamaged plastic:
B) Apply Priomat Elastic Primer 3304 Transparent or Priomat® Elastic Primer 4190
Gray. See appropriate TDS for each product.
a. An elastified surfacer must be applied over 3304 or 4190 prior to
topcoat. Some may be used wet on wet, other surfacers may require
sanding.
Recoat with:
®
Elastified Permasolid Vario Surfacer 8590
®
Elastified Permasolid Spectro Surfacer 5400
®
Elastified Permacron 2.1 Surfacer 5155
®
Elastified Permasolid 2.1 Surfacer 5157
®
Elastified Permasolid Spectro Sealer 5450
*See TDS for each surfacer for special mixing and application instructions for
use over plastic substrates.
Finish with a top coat system.
Special Notes
When using VHS Hardeners, be sure the mixture is stirred very thoroughly.
See Wizard® product retrieval or specific TDS for mixing with VHS Hardeners
®
®
No elastic additive is required in Permacron Series 293/295, Permahyd Hi-TEC 480,
Permacron® Semi-Gloss Elastic Clear Coat 8070 or Permasolid® Clear Coat Additive 8091
 2013 Axalta Coating Systems and all affiliates. All rights reserved.
The Paint System for plastic parts
Important Regulatory Information


For industrial use only by professional, trained painters. Not for sale to or use by the general public.
Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture
will have hazards of all components. Ready to use paint materials containing isocyanates can cause
irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies
and anyone with a history of respiratory complaints must not be asked to work with products containing
isocyanates. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying
respirator with particulate filters or appropriate ventilation, and gloves.
Any analytical results set forth herein do not constitute a warranty of specific product features or of the product’s
suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby
disclaim all warranties and representations, express or implied, with respect to this product, including any
warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark
law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale,
manufacturing or use may result in civil and criminal penalties.
SPIES HECKER
47818 West Anchor Court
Plymouth, MI 48170
Tel. 800-447-7437 (800-44-SPIES)
Fax 734-354-3405
www.SpiesHeckerUSA.com
 2013 Axalta Coating Systems and all affiliates. All rights reserved.
The Paint System for plastic parts
Raw
Plastic
7081
with
scuff pad
Bake
15-30
min.
7081
with
scuff pad
Repair or
New
New Cover
3304/
4190*
3300*/
Surfacer
with 3302
Flexed
Surfacer
Paint
Sand /
Paint
Paint –
WOW
(best practice)
 2013 Axalta Coating Systems and all affiliates. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement