Installation Instructions for Cessna 310 . . 400 Series Aircraft

Installation Instructions for Cessna 310 . . 400 Series Aircraft
Installation Instructions for Cessna 310 . . 400 Series Aircraft
Sunvisor System
(Kit RC300/400-300-1)
(Kit RCS-300-6)
R1180000-006
Doc: 9051-0118-015
This is a FAA STC’d installation requiring a logbook entry upon completion.
Rev
C
Date
11/5/2007
Approved
GH
Installing your Rosen Sunvisor System is easily performed and should take approximately 1 hour.
Please read these short instructions COMPLETELY before starting.
Tools Required (not included):
Phillips Screwdriver
5/32 Allen Key
9/64 Allen Key
Installation Hardware (included):
Qty:
(4) #10-32 Flat Head Screw
NOTE: On Cessna 310’s this system will only fit
applications that have the original ball joint style
equipment as shown.
•
Using a Philips screwdriver, remove (2) stock ball mount visors.
•
If your mounting holes are positioned fore and aft in relationship to the centerline of your aircraft, your
swivel should look like this when viewed from behind:
•
If your mounting holes are positioned perpendicular to the centerline of your
aircraft, your swivel should look like this when viewed from behind:
•
If necessary, reconfigure swivel mount bracket as indicated.
86365 College View Road
Eugene, Oregon USA 97405
www.rosenvisor.com
541.747.0034
Page 1 of 2
•
This image is the pilot’s side of a longitudinal
configuration.
•
Attach your new Rosen Sunvisors using the #1032 Flat Head Screws provided. NOTE: The red
Thumb Screw knob should be forward, away
from the operator.
•
Repeat for the other side.
•
Installation is now complete.
Use and Care Instructions:
•
Visors will stow in different positions, but generally the system will stow overhead when in the forward
position.
Continued Airworthiness Instructions:
•
•
(On the ground only)
o
Periodically clean the lenses with a soft cloth, mild soap and water or an approved
aviation grade windscreen cleaner. Do not use abrasives on the lens.
o
Periodically adjust the pivot tensions on the visor assemblies.
Updates to this continued airworthiness section are available on the Rosen Website.
(www.rosenvisor.com)
The most up to date version of this document is available on the Rosen Website. (www.rosenvisor.com)
Airworthiness Limitations:
The Airworthiness Limitations Section is FAA approved and specifies maintenance required under
§§43.16 and 91.403 of the Federal Aviation Regulations unless an alternative program has been FAA
approved.
There are no airworthiness limitations associated with this installation.
86365 College View Road
Eugene, Oregon USA 97405
www.rosenvisor.com
541.747.0034
Page 2 of 2
Installation Instructions for Cessna 414A, 421B Series Aircraft
Sunvisor System
(Kit R1181300-0)
This is a FAA STC’d installation requiring a logbook entry upon completion.
Doc: 9051-0118-022
Rev
Date
Approved
C 11/6/2007
GH
Installing your Rosen Sunvisor System is easily performed and should take approximately 1 hour.
Please read these short instructions COMPLETELY before starting.
Installation Hardware (included):
Qty:
(2) E-clip
(1) #10-32 Cap Screw
(1) #8-32 x 5/8 Cap Screw
(1) 5/32 Allen Key
(1) 9/64 Allen Key
NOTE: This installation fits Cessna Models 414A and 421B aircraft with standard visor on swing mounts.
•
Remove the stock visors by loosening the socket head cap screws on
the swing arms and then removing the E-clips from the top surface.
Work the visor assembly down to remove.
•
Install the Rosen swivel into the swing arm from the bottom up, with
the E-clip groove towards the top, until the groove is accessible from
above the swing arm, and install the provided E-clip on the top
surface.
•
Pull the swivel down until the E-clip rests on the top surface of the swing arm. Tighten the swivel
clamp socket head cap screw on the swing arm (see above illustration).
•
Rotate the swing arm until the swivel post is as vertical as possible. (It may be necessary to loosen
the swing arm pivot clamp using an Allen key through the trim access hole.) Tighten the swing arm
pivot clamp.
NOTE: The red slide tensioning screw should be towards the windscreen when properly installed.
•
Remove the protective paper coverings from both sides of the visor before use.
•
Installation is now complete.
86365 College View Road
Eugene, Oregon USA 97405
www.rosenvisor.com
541.747.0034
Page 1 of 2
Continued Airworthiness Instructions:
•
•
(On the ground only)
o
Periodically clean the lenses with a soft cloth, mild
soap and water or an approved aviation grade
windscreen cleaner. Do not use abrasives on the
lens.
o
Periodically adjust the pivot tensions on the visor
assemblies.
Updates to this continued airworthiness section are available
on the Rosen Website. (www.rosenvisor.com)
The most up to date version of this document is available on the
Rosen Website. (www.rosenvisor.com)
Airworthiness Limitations:
The Airworthiness Limitations Section is FAA approved and specifies maintenance required under
§§43.16 and 91.403 of the Federal Aviation Regulations unless an alternative program has been FAA
approved.
There are no airworthiness limitations associated with this installation.
86365 College View Road
Eugene, Oregon USA 97405
www.rosenvisor.com
541.747.0034
Page 2 of 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement