OG WA-03-R
OPERATION GUIDE
UHF Wireless Audio Module
WA-TX-03-R / WA-RX-03-R
Operation Guide
Version 1.6 (Sep. 2015)
CIRCUIT DESIGN, INC.,
7557-1 Hotaka, Azumino-city
Nagano 399-8303 JAPAN
Tel: + +81-(0)263-82-1024
Fax: + +81-(0)263-82-1016
e-mail: [email protected]
http://www.circuitdesign.jp
OG_WA-03-R_V16e
OPERATION GUIDE
CONTENTS
GENERAL DESCRIPTION ............................................................... 3
FEATURES ....................................................................................... 3
APPLICATION .................................................................................. 3
SPECIFICATION ............................................................................... 4
TERMINAL DESCRIPTION .............................................................. 5
CHANNEL TABLE ............................................................................. 7
REMARKS FOR INTEGRATION OF THE RECEIVER ANTENNA ... 7
CONNECTION DIAGRAM ................................................................. 8
BLOCK DIAGRAM ............................................................................ 9
DIMENSIONS ................................................................................. 11
REGULATORY COMPLIANCE INFORMATION ............................. 13
DECLARATION OF CONFORMITY ................................................ 15
CAUTIONS AND WARNINGS ......................................................... 16
REVISION HISTORY ....................................................................... 17
OG_WA-03-R_V16e
2
Circuit Design, Inc.
OPERATION GUIDE
GENERAL DESCRIPTION
The WA-TX-03-R / WA-RX-03-R are 15ch multichannel audio modules that operate
in the European harmonized 863 - 865 MHz band. In addition to offering a frequency
range sufficient for voice transmission, the compander noise reduction system has a
wide dynamic range, enabling transmission of clear audio signals.
As embedded devices, they include nearly all the parts necessary for audio
transmission in a small shielding case, making it possible to develop audio
transmission equipment in a short time.
FEATURES








863 – 865 MHz European Audio band
15 channels, 125 kHz steps
70 dB dynamic range with built in noise reduction system
50 Hz - 13 kHz audio response
Low power operation
Adjustable mute level
Small size for embedding in user equipment
R&TTE (EN301 357) and RoHS compliant
APPLICATIONS






Audio guiding in museums
Tour guide systems
Wireless conference systems
Wireless microphone systems for amateur users
Various audio transmissions
Voice monitoring
OG_WA-03-R_V16e
3
Circuit Design, Inc.
OPERATION GUIDE
SPECIFICATION
Common
Items
Compatible standard
Frequency range
Number of channels
Emission class
Operating distance
S/N ratio
Audio frequency response
T.H.D
Emphasis
Operating temperature range
Specification
EN 301 357
863 – 865 MHz
15
F3E
50 m
70 dB or more
50 Hz-13 kHz
2%
50 us
0 to 50 °C
WA-TX-03-R (Transmitter)
Items
Oscillation type
RF power
Frequency stability
Noise reduction
Spurious emission
Deviation
AF input level
AF input impedance
Maximum DC input to AF input
Supply voltage
Consumption current
Dimensions
Weight
Specification
Crystal based PLL oscillation
2 mW (e.r.p)
+/- 15 kHz
Compander
1 uW max.
20 kHz
- 93 to -13 dBv
20 kΩ or more
7 V DC max
4.2 to 6 V
70 mA
36 x 26 x 8 mm
13 g
Remarks
R&TTE
125 kHz step
Line-of-sight
W/IHF-A Filter
+/-3.5 dB
@AF 1kHz, Δf = 20kHz
Remarks
1 kHz @ -25 dBv
1 kHz
3.6 to 7 V *1
Excluding protrusion
*1 Supply voltage: 3.6 to 7V – Possible operating range without meeting full specifications
WA-RX-03-R (Receiver)
Items
Receiver type
Local oscillator type
IF Frequency
Noise reduction system
Receiver sensitivity
Squelch sensitivity
AF output level
AF output impedance
Supply voltage
Consumption current
Dimensions
Weight
*0 dBv=0.775 V
Specification
Single super heterodyne
Crystal based PLL oscillation
10.7 MHz
Expander
21 dBuV (- 92 dBm)
Adjustable
- 10 dBv
20 kΩ or less
3 to 5 V
45 mA
36 x 26 x 8 mm
13 g
Remarks
S/N 55 dB
by external VR
Δf = 20 kHz
Excluding protrusion
* The data was taken at 25 C unless otherwise specified
OG_WA-03-R_V16e
4
Circuit Design, Inc.
OPERATION GUIDE
TERMINAL DESCRIPTION
WA-TX-03-R transmitter module
No.
Name
I/O
Description
LED terminal for unavailable channels.
The terminal is high when any channel
outside CH 1 to 15 is selected.
LED can be powered directly
1
UNA
O
2
SW0
I
3
SW1
I
4
SW2
I
5
SW3
I
6
NC
-
7
NC
-
Equivalent circuit
Transmitter channel setting terminal
Select channel within 15 programmed
channels
Refer to “Channel table”
Terminal for stand-by with power off delay
Set to high to enter standby.
Set to ground when transmitting.
8
STB
I
9
AF
I
Audio signal input terminal
Audio input signal level -93 dBv to -13 dBv
Power supply (+) terminal
Voltage range is DC 4.2 to 6 V
A power source without ripple noise should
be used.
A protection diode for reverse connection is
provided in the circuit.
10
VCC
I
11
ANT
O
12
GND
OG_WA-03-R_V16e
I
Antenna terminal (RF output)
50 Ω impedance
GND terminal
The ground is for the power supply and
antenna radial.
Connect it to a wide ground plane for efficient
antenna emissions and stable operation.
5
Circuit Design, Inc.
OPERATION GUIDE
WA-RX-03-R receiver module
CN1
No.
1
2
3
Name
I/O
CON
LED
UNA
Equivalent circuit
I
Terminal for adjustment of mute level.
Connect a 10 to 20 kΩ VR to the terminal for
mute level adjustment.
The mute level is the threshold level of the
received signal field strength so as not to
output the received signal below the threshold
level.
O
MUTE LED terminal
The terminal is high when mute is in operation.
It is low when the AF signal is output, so that
the LED connecting the terminal works as an
AF output indicator showing the AF output
status.
The terminal is an open collector and is
connected to a 220Ω resistor (Max 10mA).
O
LED terminal for unavailable channels.
The terminal is high when any channel other
than CH 1 to 15 is selected.
The LED can be powered directly
4
VCC
I
5
AF
O
6
GND
7
ANT
OG_WA-03-R_V16e
Description
I
Power supply (+) terminal
The voltage range is DC 3.0 to 5 V
A power source without ripple noise should be
used.
Be sure to connect it with the correct polarity.
To maintain a lower voltage, a protection diode
is not provided in the circuit.
Audio output terminal
Output impedance is 20 kΩ.
Connection to a low input impedance interface
will decrease the output level.
Maximum output level is –10 dBv
When an audio amplifier is used, if the
amplified output is distorted by the MIC input,
insert an attenuator.
GND terminal
The ground is for the power supply and
antenna radial.
Connect it to a wide ground plane for stable
operation.
Antenna terminal (RF input).
50 Ω impedance
6
Circuit Design, Inc.
OPERATION GUIDE
CN2
No.
Name
I/O
1
SW0
I
2
SW1
I
3
SW2
I
Description
Equivalent circuit
Receiver channel setting terminal
Selects a channel within 15 programmed
channels
Refer to “Channel table”
4
SW3
I
5
NC
-
6
NC
-
CHANNEL TABLE
CH
TX/RX frequency
SW0
SW1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Unavailable
863.125
863.250
863.375
863.500
863.625
863.750
863.875
864.000
864.125
864.250
864.375
864.500
864.625
864.750
864.875
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
H
L
L
H
H
L
L
H
H
L
L
H
H
L
L
SW2
H
H
H
H
L
L
L
L
H
H
H
H
L
L
L
L
SW3
H
H
H
H
H
H
H
H
L
L
L
L
L
L
L
L
L = GND
Remarks for integration of the receiver antenna
Please pay due attention to the design of the antenna ground plane based on the general design theory.
Locate the antenna in a place where there are no objects between TX and RX and that is visible from
the transmitter antenna. If a PCB pattern line is used for connection between the antenna terminal and
the antenna you choose, please secure the following pattern width.
0.8
1
1.2
1.6
PCB thickness (mm)
1.3
1.4
1.7
2.7
Pattern width (mm)
(The example above shows a case where a G10 double-sided PCB is used.)
OG_WA-03-R_V16e
7
Circuit Design, Inc.
OPERATION GUIDE
CONNECTION EXAMPLE (WA-RX-03-R)
OG_WA-03-R_V16e
8
Circuit Design, Inc.
OPERATION GUIDE
BLOCK DIAGRAM (WA-TX-03-R)
OG_WA-03-R_V16e
9
Circuit Design, Inc.
OPERATION GUIDE
BLOCK DIAGRAM (WA-RX-03-R)
OG_WA-03-R_V16e
10
Circuit Design, Inc.
OPERATION GUIDE
DIMENSION WA-TX-03-R
Reference hole position (Top view)
OG_WA-03-R_V16e
11
Circuit Design, Inc.
OPERATION GUIDE
DIMENSION
WA-RX-03-R
Reference hole position (Top view)
OG_WA-03-R_V16e
12
Circuit Design, Inc.
OPERATION GUIDE
Regulatory Compliance Information
Regulatory compliance of the WA-TX-03-R and the WA-RX-03-R
The WA-TX-03-R and the WA-RX-03-R are designed for embedding in other equipment.
(Products incorporating the WA-TX-03-R and the WA-RX-03-R are henceforward referred to as final
products.)
The European regulation applicable to the WA-TX-03-R and the WA-RX-03-R is the R&TTE Directive
1999/5/EC.
The WA-TX-03-R and the WA-RX-03-R are intended to be used for the Radio Microphones defined in the
ERC/REC 70-03 Annex 10 and for the Wireless Audio Applications in the ERC/REC 70-03 Annex 13 (EN 301
357*)
The conformity assessment for the WA-TX-03-R and the WA-RX-03-R were completed in accordance with
the R&TTE Directive Annex II (RX) & III (TX) procedures, and the Declaration of Conformity is attached to this
manual.
* NOTE: EN 301 357 defines the equipment covered by its standard and the output power limits depend on the
equipment type. The WA-TX-03-R meets the output power limits allowed for all equipment types except for “in-vehicle
cordless” and “personal cordless”. If the WA-TX-03-R is used for “in-vehicle cordless” or “personal cordless”
equipment, the manufacturer is required to design the final product within the specified output power limit and to
perform the conformity assessment of the final product to EN 301 357.
Cautions related to regulatory compliance when embedding WA-TX-03-R/WA-RX-03-R
1. Antenna for the WA-TX-03-R
The WA-TX-03-R is supplied without a dedicated antenna and the user is required to provide an antenna.
The conformity assessment of the WA-TX-03-R was performed using Circuit Design’s evaluation board
and antenna (1/4 lambda lead antenna). We recommend that you use our standard antenna (ANT-LEA-02
or ANT-RIG-02), or an antenna with equivalent characteristics and performance. For details about our
evaluation boards and antennas, refer to www.circuitdesign.jp or contact us. If you use an antenna other
than the recommended antenna, further radio conformity assessment may be required.
2. Supply voltage of the WA-TX-03-R
The WA-TX-03-R should be used within the specified voltage range (4.2 V to 6.0 V).
3. Enclosure
To fulfill the requirements of EMC and safety requirements, the WA-TX-03-R and the WA-RX-03-R should
be mounted on the circuit boards of the final products and must be enclosed in the cases of the final
products. No surface of the WA-TX-03-R and the WA-RX-03-R should be exposed.
4. Cordless audio transmitter shutoff
The WA-TX-03-R does not have automatic transmitter shutoff function in the module. The manufacturer of
the final product is required to design the final product to have such function in accordance with EN 301
357.
OG_WA-03-R_V16e
13
Circuit Design, Inc.
OPERATION GUIDE
EMC requirements according to the R&TTE Directive Article 3.1b
The ESD-test (Electro Static Discharge test) was not performed on the WA-TX-03-R and the WA-RX-03-R.
The WA-TX-03-R and the WA-RX-03-R are designed for embedding in final products and rely on the
enclosures of the final products to provide the necessary protection. The ESD test should be performed on
the final products incorporating the WA-TX-03-R and the WA-RX-03-R.
Safety requirements according to the R&TTE Directive Article 3.1a
The WA-TX-03-R and the WA-RX-03-R rely on the final products to provide the electrical, mechanical, and
fire enclosure requirements.
The nominal supply voltage of the WA-TX-03-R is 4.2 – 6.0V and the WA-RX-03-R is 3.0 V – 5.0 VDC. The
worst input currents under normal operating conditions are 70mA and 45mA respectively. The final product
should be capable of supplying these power requirements.
The WA-TX-03-R and the WA-RX-03-R are entirely SELV (Separated Extra Low Voltage) when the supply
input from the final product is SELV, i.e. the WA-TX-03-R and the WA-RX-03-R are Class III equipment in
which protection against electric shock relies on a supply from an SELV circuit and in which hazardous
voltage is not generated.
The WA-TX-03-R and the WA-RX-03-R should be installed in the final products so that the required creepage
and clearance distances (within the final products) are maintained.
Conformity assessment of the final product
The manufacturer of the final product is responsible for the conformity assessment procedures of the final
product in accordance with the R&TTE Directive.
As to the conformity assessment of the R&TTE Directive Article 3.2 (Efficient use of the radio spectrum), the
manufacturer of the final products incorporating the R&TTE assessed WA-TX-03-R and WA-RX-03-R will be
exempted from its conformity assessment procedures. For details of how to use the conformity assessment
of the WA-TX-03-R and the WA-RX-03-R, please consult the relevant authorities or accredited certification
bodies.
Notification of the final product
The notification required by R&TTE Directive Article 6 (4) is not necessary if the final product is used in the
harmonized frequency band and is classified as Class-1 equipment. If the final product is not used in the
harmonized frequency band and is classified as Class-2 equipment, the manufacturer of the final product has
a duty to notify the relevant radio regulatory authorities in the countries where the final product is sold.
Exemption clause
Circuit Design, Inc does not guarantee the accuracy of the above mentioned information about the conformity
assessment and notification of the final product. Directives, technical standards, principles of operation and
the like may be interpreted differently by the authorities in each country. Also the national laws and
restrictions vary with the country. In case of doubt or uncertainty, we recommend that you check with the
authorities or official certification organizations of the relevant countries.
OG_WA-03-R_V16e
14
Circuit Design, Inc.
OPERATION GUIDE
OG_WA-03-R_V16e
15
Circuit Design, Inc.
OPERATION GUIDE
Important notice

Customers are advised to consult with Circuit Design sales representatives before ordering.
Circuit Design believes the provided information is accurate and reliable. However, Circuit Design reserves the
right to make changes to this product without notice.

Circuit Design products are neither designed nor intended for use in life support applications where malfunction
can reasonably be expected to result in significant personal injury to the user. Any use of Circuit Design products
in such safety-critical applications is understood to be fully at the risk of the customer and the customer must
fully indemnify Circuit Design, Inc for any damages resulting from any improper use.
 As the radio module communicates using electronic radio waves, there are cases where transmission will be
temporarily cut off due to the surrounding environment and method of usage. The manufacturer is exempt from
all responsibility relating to resulting harm to personnel or equipment and other secondary damage.
 The manufacturer is exempt from all responsibility relating to secondary damage resulting from the operation,
performance and reliability of equipment connected to the radio module.
Copyright
 All rights in this operation guide are owned by Circuit Design, Inc. No part of this document may be copied or
distributed in part or in whole without the prior written consent of Circuit Design, Inc.
Cautions
 Do not use the equipment within the vicinity of devices that may malfunction as a result of electronic radio waves
from the radio module.
 Communication performance will be affected by the surrounding environment, so communication tests should be
carried out before actual use.
 Ensure that the power supply for the radio module is within the specified rating. Short circuits and reverse
connections may result in overheating and damage and must be avoided at all costs.
 Ensure that the power supply has been switched off before attempting any wiring work.
 The case is connected to the GND terminal of the internal circuit, so do not make contact between the '+' side of
the power supply terminal and the case.
 When batteries are used as the power source, avoid short circuits, recharging, dismantling, and pressure. Failure
to observe this caution may result in the outbreak of fire, overheating and damage to the equipment. Remove the
batteries when the equipment is not to be used for a long period of time. Failure to observe this caution may
result in battery leaks and damage to the equipment.
 Do not use this equipment in vehicles with the windows closed, in locations where it is subject to direct sunlight,
or in locations with extremely high humidity.
 The radio module is neither waterproof nor splash proof. Ensure that it is not splashed with soot or water. Do not
use the equipment if water or other foreign matter has entered the case.
 Do not drop the radio module or otherwise subject it to strong shocks.
 Do not subject the equipment to condensation (including moving it from cold locations to locations with a
significant increase in temperature.)
 Do not use the equipment in locations where it is likely to be affected by acid, alkalis, organic agents or corrosive
gas.
 Do not bend or break the antenna. Metallic objects placed in the vicinity of the antenna will have a great effect on
communication performance. As far as possible, ensure that the equipment is placed well away from metallic
objects.
 The GND for the radio module will also affect communication performance. If possible, ensure that the case GND
and the circuit GND are connected to a large GND pattern.
Warnings
 Do not take a part or modify the equipment.
 Do not remove the product label (the label attached to the upper surface of the module.) Using a module from
which the label has been removed is prohibited.
Copyright 2015, Circuit Design, Inc.
OG_WA-03-R_V16e
16
Circuit Design, Inc.
OPERATION GUIDE
REVISION HISTORY
Version
1.0
1.1
1.2
1.3
1.4
1.5
1.6
Date
July 2007
Aug. 2007
Feb. 2009
Jan. 2010
Oct. 2010
Oct. 2013
Sep. 2015
OG_WA-03-R_V16e
Description
The first issue
Add DOC (Page 15)
DOC updated, Important notice added
Misdescription corrected in the Dimension drawings
DOC updated
Misdescription corrected in the Terminal description
DOC updated
17
Remark
Page 15 & 16
Page 11 & 12
Page 15
Page 6
Page 15
Circuit Design, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement