JVC DR-MV5SEK User Guide Manual Operating Instruction Pdf

JVC DR-MV5SEK User Guide Manual Operating Instruction Pdf
Filename [MV5SEK_01Cov1.fm]
MV5SEK_00.book Page 1 Wednesday, August 31, 2005 7:58 PM
DVD VIDEO RECORDER &
VIDEO CASSETTE RECORDER
DR-MV5SEK
DR-MV5BEK
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
INSTRUCTIONS
LPT1037-001C
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
Filename [MV5SEK_02Safety.fm]
MV5SEK_00.book Page 2 Wednesday, August 31, 2005 7:58 PM
2
EN
Masterpage:Left0
SAFETY FIRST
Safety Precautions
The rating plate and the safety caution are on the rear of the unit.
WARNING: DANGEROUS VOLTAGE INSIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION:
A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS
UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE UNIT CORRECTLY AS
INSTRUCTED.
WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO
NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE
DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE
INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CLASS 1 LASER PRODUCT
REPRODUCTION OF LABELS
WARNING LABEL INSIDE OF THE UNIT
IMPORTANT:
8 Please read the various precautions on pages 2 and 3 before
installing or operating the unit.
8 It should be noted that it may be unlawful to re-record prerecorded tapes, DVDs, or discs without the consent of the
owner of copyright in the sound or video recording, broadcast
or cable programme and in any literary, dramatic, musical, or
artistic work embodied therein.
CAUTION:
8 When you are not using the unit for a long period of time, it is
recommended that you disconnect the power cord from the
mains outlet.
8 Dangerous voltage inside. Refer internal servicing to qualified
service personnel. To prevent electric shock or fire hazard,
remove the power cord from the mains outlet prior to
connecting or disconnecting any signal lead or aerial.
● VIDEO Plus+ and PlusCode are registered trademarks of Gemstar
Development Corporation. The VIDEO Plus+ system is manufactured
under licence from Gemstar Development Corporation.
● This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must
be authorised by Macrovision Corporation, and is intended for home
and other limited viewing users only unless otherwise authorised by
Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
The STANDBY/ON 1 button does not completely shut off
mains power from the unit, but switches operating current on and
off. “`” shows electrical power standby and “!” shows ON.
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly.
Failure to heed the following precautions may result in
damage to the unit, remote control or disc.
1. DO NOT place the unit —
— in an environment prone to extreme temperatures or
humidity.
— in direct sunlight.
— in a dusty environment.
— in an environment where strong magnetic fields are
generated.
— on a surface that is unstable or subject to vibration.
2. DO NOT block the unit’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the unit or remote control.
4. DO NOT place anything which might spill on top of the unit
or remote control.
(If water or liquid is allowed to enter this equipment, fire or
electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with
water. Also DO NOT place any containers filled with water or
liquids (such as cosmetics or medicines, flower vases, potted
plants, cups, etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted
candles, on the apparatus.
8. AVOID violent shocks to the unit during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the unit when you move it from
a cold place to a warm place, or under extremely humid
conditions—just as water droplets form on the surface of a glass
filled with cold liquid. In conditions where condensation may occur,
disconnect the unit’s power plug from the wall and keep it
disconnected for a few hours to let the moisture dry, then turn on
the unit.
ATTENTION:
To mobile phone users:
Using a mobile phone in the vicinity of the unit may cause picture
vibration on the TV screen or change the screen to a blue back
display.
● Manufactured under license from Dolby Laboratories. “Dolby” and
double-D symbol are trademarks of Dolby Laboratories.
● “DTS” and “DTS Digital Out” are trademarks of Digital Theater
Systems, Inc.
● Cassettes marked “VHS” (or “S-VHS”) can be used with this unit.
However, S-VHS recording is not possible with this model.
● This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that
makes it possible to play back S-VHS recordings in the SP mode with
regular VHS resolution.
● HQ VHS is compatible with existing VHS equipment.
2
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
On placing the unit:
Some TVs or other appliances generate strong magnetic fields.
Do not place such appliances on top of the unit as it may cause
picture disturbance.
Wednesday, 31 August 2005 19:57
Filename [MV5SEK_02Safety.fm]
Masterpage:Right+
MV5SEK_00.book Page 3 Wednesday, August 31, 2005 7:58 PM
SAFETY FIRST
IMPORTANT:
Connection to the mains supply in the United Kingdom.
DO NOT cut off the mains plug from this equipment.
If the plug fitted is not suitable for the power points in your home
or the cable is too short to reach a power point, then obtain a
proper safety approved extension lead/adapter or consult your
dealer.
In the unlikely event of the plug fuse failing be sure to
replace the fuse only with an identical approved type, as
originally fitted, and to replace the fuse cover. If the fuse
fails again consult your nearest JVC dealer.
If nonetheless the mains plug is cut off remove the fuse and
dispose of the plug immediately, to avoid a possible shock
hazard by inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains plug then follow
the instructions given below:
DO NOT make any connection to the Larger Terminal coded E or
Green.
The wires in the mains lead are coloured in accordance with the
following code:
Blue to N (Neutral) or Black
Brown to L (Live) or Red
If these colours do not correspond with the terminal
identifications of your plug, connect as follows:
Blue wire to terminal coded N (Neutral) or coloured Black.
Brown wire to terminal coded L (Live) or coloured Red.
If in doubt — consult a competent electrician.
Some Do’s And Don’ts On The Safe Use
Of Equipment
This equipment has been designed and manufactured to meet
international safety standards but, like any electrical
equipment, care must be taken if you are to obtain the best
results and safety is to be assured.
DO
DO
DO
DO
read the operating instructions before you attempt to use
the equipment.
ensure that all electrical connections (including the mains
plug, extension leads and interconnections between
pieces of equipment) are properly made and in
accordance with the manufacturer’s instructions. Switch off
and withdraw the mains plug when making or changing
connections.
consult your dealer if you are ever in doubt about the
installation, operation or safety of your equipment.
be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt
about it working normally, or if it is damaged in any way —
switch off, withdraw the mains plug and consult your
dealer.
DON’T remove any fixed cover as this may expose dangerous
voltages.
DON’T leave equipment switched on when it is unattended unless
it is specifically stated that it is designed for unattended
operation or has a standby mode. Switch off using the
switch on the equipment and make sure that your family
knows how to do this. Special arrangements may need to
be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that
you are distracted from the requirements of road safety. It
is illegal to watch television whilst driving.
DON’T listen to headphones at high volume, as such use can
permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with
curtains or soft furnishings. Overheating will cause
damage and shorten the life of the equipment.
3
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
EN
3
DON’T use makeshift stands and NEVER fix legs with wood
screws — to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings
provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or
moisture.
ABOVE ALL...
—NEVER let anyone especially children push anything into holes,
slots or any other opening in the case — this could result in a fatal
electrical shock;
—NEVER guess or take chances with electrical equipment of any
kind — it is better to be safe than sorry!
Check Contents
CHECK ALL THE CONTENTS SHOWN BELOW.
DVD Video Recorder & Video Cassette Recorder
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
Infrared Remote
Control Unit
RF Cable
“AA” Batteries (x 2)
21-pin SCART Cable
4You are now ready to install your unit. (墌 pg. 15)
Information for Users on Disposal of Old Equipment
[European Union]
This symbol indicates that the electrical and
electronic equipment should not be
disposed as general household waste at its
end-of-life. Instead, the product should be
handed over to the applicable collection
Attention:
point for the recycling of electrical and
electronic equipment for proper treatment, This symbol is only
recovery and recycling in accordance with valid in the
European Union.
your national legislation.
By disposing of this product correctly, you
will help to conserve natural resources and
will help prevent potential negative effects on the environment
and human health which could otherwise be caused by
inappropriate waste handling of this product. For more
information about collection point and recycling of this product,
please contact your local municipal office, your household waste
disposal service or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste,
in accordance with national legislation.
(Business users)
If you wish to dispose of this product, please visit our web page
www.jvc-europe.com to obtain information about the take-back
of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in
accordance with applicable national legislation or other rules in
your country for the treatment of old electrical and electronic
equipment.
Wednesday, 31 August 2005 19:57
Filename [MV5SEK_03Contents.fm]
Masterpage:Right0
MV5SEK_00.book Page 4 Wednesday, August 31, 2005 7:58 PM
Contents
Enjoying your life with DV
Enjoying your life with
DVD r
Beautiful
images
Enjoy the vivid picture quality of
DVD recording/playback.
OH!! !
Great!
Beautifu
Easy
dubbing
With the simple operation, you
can dub from DVD to tape or
tape to DVD.
4
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:57
Filename [MV5SEK_03Contents.fm]
Masterpage:Right0
MV5SEK_00.book Page 5 Wednesday, August 31, 2005 7:58 PM
CONTENTS
ur life with DVD
recorder
Choose the disc type for
recording from DVD-RAM, DVDRW and DVD-R.
3 types of
DVD discs
Read me first!
For your safety .................................... 2
About discs .......................................... 6
Index ................................................. 10
Are you ready?
Get over it!
– connections – .............. 15
Initial settings .................................... 17
Let’s enjoy...
Basic playback .............. 24
Basic recording .............. 26
Using timer ....................................... 29
All over dubbing ................................ 37
Advanced playback ........................... 47
Advanced recording .......................... 61
What’s navigation? ............................ 65
Beautiful!
Comfortable
playback
Navigation function helps you to
find the disc and programme you
want to watch.
Arrange your style
1 remote control is good enough! ..... 74
For better sound ................................ 76
It can be more useful ......................... 78
Need help?
Tips for your trouble .......................... 91
Terms ................................................. 99
5
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:57
Filename [MV5SEK_04DiscInfo.fm]
Masterpage:Left0
MV5SEK_00.book Page 6 Wednesday, August 31, 2005 7:58 PM
6
EN
DISC INFORMATION
About Discs
Recordable/Playable Discs
You can use discs with the following logos for recording and
playback.
DVD-RAM
12 cm: 4.7 GB/9.4 GB
8 cm: 1.4 GB/2.8 GB
Ver. 2.0/2x speed
Ver. 2.1/1x – 2x speed
DVD-RW
12 cm: 4.7 GB/9.4 GB
Ver. 1.1/1x – 2x speed (Video mode/VR mode)
DVD-R
12 cm: 4.7 GB
8 cm: 1.4 GB
Ver. 2.0/1x – 4x speed (Video mode)
● The above table is based on the information as of April 2005.
● Recording and playback may not be performed depending on the
characteristics and condition of the disc used, leading to
unsatisfactory results. Using discs manufactured by JVC is
recommended since they have been tested to be compatible with this
unit.
DVD-RAM Discs
It is only possible to use discs which conform with DVD-RAM
standard Version 2.0 or 2.1.
● It is impossible to record on DVD-RAM discs which do not conform to
this standard. If you use a disc formatted under a different standard
version, format it on this unit before use.
● It may not be possible to record, play back, edit or dub a DVD-RAM
disc even if it conforms to the standard if it was recorded or edited on
the devices from other manufacturers or on a PC, or if it has far too
many titles, or if there is very little available capacity remaining on the
disc.
● DVD-RAM discs recorded on this unit cannot be played back on an
incompatible DVD player.
● It is possible to record copy-once programmes of digital broadcasts
only onto 4.7/9.4 GB DVD-RAM discs (2.8 GB DVD-RAM discs are
not compatible).
DVD-R/RW Discs
It is only possible to use DVD-R discs which conform with DVD-R
standard Version 2.0.
When a DVD-R/RW disc (Video mode) is finalised (墌 pg. 90), it
can be played back on a standard DVD player as a DVD VIDEO
disc.
When a DVD-RW disc (VR mode) is finalised (墌 pg. 90), it can be
played back on a standard DVD player compatible with the VR
mode of DVD-RW discs.
Before finalising —
— it is possible to record on unrecorded areas of the disc, edit the
disc title and programme titles, and delete programmes.
● It is impossible to record or edit DVD-R/RW discs recorded on other
devices even if they have not been finalised.
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
programme is deleted from a DVD-R disc.
6
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
After finalising —
After a DVD-R/RW disc (Video mode) has been finalised, it is
possible to play back the recorded programmes (video and/or
audio) on a standard DVD video player as a DVD VIDEO disc.
● Edited titles are displayed as the
“DVD menu” in video mode.
● It is impossible to record, edit or
delete the data either in video
mode or in VR mode.
● Either in video mode or in VR
mode, although the disc can be
played back on DVD players from
other manufacturers, sometimes it
may not be possible to play back
depending on the disc and recording conditions.
● It is impossible to record on CD-R/RW or DVD-R discs used for
authoring.
● It is impossible to record onto DVD-R/RW (Video mode) discs
broadcasts that allow you to copy once. The copy-once programmes
can only be recorded onto DVD-RW discs formatted in VR mode.
NOTE:
The following may result if you play back a DVD-R disc recorded on
another unit.
● The disc does not play.
● A mosaic pattern (block noise) appears on the screen.
● Video or audio may be dropped out.
● The unit stops during playback.
Discs For Playback Only
You can use discs with the following logos for playback only.
DVD VIDEO
Video CD/Super Video CD
(example of region code
indications)
Audio CD
CD-DA files
CD-R
CD-DA/JPEG/
MP3 files
CD-RW
CD-DA/JPEG/
MP3 files
CD-ROM
JPEG/MP3 files
● Playback may not be performed depending on the characteristics and
condition of the disc used.
● DTS Audio CDs can also be played back (An optional DTS decoder is
required).
● MP3 and JPEG discs can be played back on this unit only when they
have been recorded in the ISO9660 or Joliet format and finalised.
● JPEG files that can be played back on this unit must conform to JFIF/
Baseline process, and the maximum resolution of a JPEG file is
2,812 x 2,112 pixels.
● CD-R/RW discs recorded in music CD format need to be finalised to
play back on this unit.
● Operation and audio quality of this unit are not guaranteed for discs
that do not conform to the Compact Disc specification (CD-DA).
Before you play back a CD, check for the CD logo and read the notes
on the package to confirm that it conforms to the Compact Disc
specification.
● Depending on the intentions of the author of the software, recording
conditions of DVD discs and Video CD discs may be restricted. Since
this unit plays back discs according to the intentions of the author of
the software as indicated on the disc, some functions may not
operate as commanded.
● When switching from the first layer to the second layer of doublelayered DVD VIDEO discs, the image and sound may be momentarily
distorted. This is not a malfunction.
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_04DiscInfo.fm]
Masterpage:Right+
MV5SEK_00.book Page 7 Wednesday, August 31, 2005 7:58 PM
DISC INFORMATION
● DVD-AUDIO discs compatible with DVD video players can be played.
● Super Audio CDs (SACD) compatible with conventional CD players
can be played.
● It is possible to play back finalised +R/+RW (Video mode only) discs.
“DVD” lights on the front display panel when a +R/+RW disc is
loaded.
However, the use of +R double layer disc on this unit may not be
recommended.
Unplayable Discs
The following types of discs cannot be played using this unit.
Do not attempt to play back any kind of disc that is damaged
(cracked, warped, or repaired with adhesive tape) or discs in
unusual shapes (heart-shaped, octagonal, or other forms). If such
discs are accidentally played back, it may cause noise that can
lead to speaker damage.
●
●
●
●
CD-ROM discs (including PHOTO-CD and CD-G)
Discs recorded in Packet Write (UDF) format
1.3-GB double density CDs (DDCD)
High density CDs (HDCD)
The following discs also cannot be played back.
● Discs of a region number other than “2”
● DVD-RAM (2.6 GB/5.2 GB)
● DVD-RAM (TYPE1)
EN
7
Recording Medium And Format
DVD-RAM
● Recording and erasing can be performed as many times as possible
on a disc.
● Editing can be performed after recording, such as deleting unwanted
parts.
● While recording, it is possible not only to start playback of a
programme currently being recorded, but also to watch another
programme previously recorded.
DVD-RW (VR mode)
● Recording and erasing can be performed as many times as possible
on a disc.
● Editing can be performed after recording, such as deleting unwanted
parts.
DVD-RW (Video mode)
● Can be played back on other DVD players after finalising.
● New recording can be performed by erasing all the data on a disc
once played back.
DVD-R
● Can be played back on other DVD players after finalising.
● Suitable when keeping a recorded disc for a long time.
File Structure Of Discs
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with the
“Compact Disc Digital Audio” standard. Therefore, the use of
Non-DVD side of a DualDisc on this product may not be
recommended.
Region Number
The world is divided into 6 regions for DVD VIDEO discs.
DVD VIDEO discs are assigned a region number to indicate which
region they may be played back in. A disc cannot be played back
on this unit unless the region number of the disc matches that of
the unit. The region number for this unit is “2”. Only discs whose
region number includes “2” or “ALL” can be played back such as
shown below.
Examples of DVD VIDEO labels which can be played back
using this unit.
Marks of discs in this instruction manual
Allows operation with a
DVD-RAM disc.
Allows operation with a
Video CD/Super Video
CD (SVCD) disc.
Allows operation with a
DVD-R disc.
Allows operation with
an Audio CD disc.
Allows operation with a
DVD-RW disc.
Allows operation with a
disc including MP3
files.
Allows operation with a
DVD VIDEO disc.
Allows operation with a
disc including JPEG
files.
7
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
“titles”. Each title has a number (title number) that can be used to
select desired titles. Titles are further divided into units called
“chapters”. Each chapter has a number (chapter number) that can
also be used to select desired chapters. Note that some discs are
not divided into titles and chapters.
When you record a programme on a DVD-RAM/RW (VR mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes from monaural or bilingual
to stereo due to commercial breaks, etc. It is also possible to insert
chapter marks at desired locations during playback. (墌 pg. 49)
When you record a programme on a DVD-R/RW (Video mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes due to commercial breaks,
etc. It is also possible to insert chapter marks at desired locations
during either recording or playback. Once the disc has been
finalised, these chapter marks are deleted and new chapter marks
are assigned automatically approximately every 5 minutes.
DVD-RAM, DVD-RW, DVD-R or DVD VIDEO disc
Title 1
Chapter 1
Chapter 2
Title 2
Chapter 3
Chapter 1
Chapter 2
Chapter 3
● In Video mode, even before finalising, it is impossible to perform
editing operations other than changing the disc name and/or title
names and deleting programmes and/or titles.
● After finalising, it is impossible to perform editing operations.
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_04DiscInfo.fm]
Masterpage:Left+
MV5SEK_00.book Page 8 Wednesday, August 31, 2005 7:58 PM
8
EN
DISC INFORMATION
Audio CD/Video CD/Super Video CD (SVCD)
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video CD
discs.
However, some discs are not divided into tracks.
Audio CD or Video CD
Track 1
Track 2
Track 3
Track 4
JPEG/MP3 Disc (CD-R/RW/ROM)
MP3/JPEG files put in directories nested in several levels on a disc
will be organised as if they were put in single level directories
(groups) by the MP3/JPEG Navigation of this unit. (墌 pg. 72)
File structure of a disc before starting the MP3/JPEG
Navigation
DVD VIDEO Marks
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of the disc. Check the marks indicating the contents and
functions of the disc. Note, however, that in some cases a disc may
not include a mark even for a function it supports.
Marks related to video
Number of subtitles
Number of angles
Recorded under the
standard 4:3 aspect
ratio
Screen includes black
bands at the top and
the bottom of image
which has a standard
4:3 aspect ratio (letter
box)
Video playback is in Wide video mode (16:9) on
wide televisions, but in letter box on televisions
with standard 4:3 aspect ratio.
Directory
MP3 file
JPEG file
File structure of the disc after starting the MP3/JPEG
Navigation
Files are automatically grouped as follows and displayed on the
MP3/JPEG Navigation screen. Data is displayed in the
alphabetical order of file name. Files are grouped based on roots.
Video playback is in Wide video mode (16:9) on
wide televisions, but pan and scan is used on
televisions with standard 4:3 aspect ratio (either
the left or right side of the image is cut-out).
Marks related to audio
Number of audio tracks
Dolby Digital mark
It has been developed by Dolby Laboratories as
a digital surround system.
DTS (Digital Theater Systems)
You can enjoy DTS audio if you connect an
amplifier with a built-in DTS decoder to the
[DIGITAL AUDIO OUT] connector of the unit.
● This unit can recognise up to 9 hierarchies including directories and
files.
Also, it can recognise up to 250 files in each group, and up to 99
groups on a disc.
NOTES:
● Video CD discs that support Playback Control (PBC)
The contents of a disc are recorded into several hierarchies, and played
back according to the instructions on the screen while navigating through
the hierarchies. It is also possible to playback recorded tracks
consecutively without activating the PBC function even when playing a
PBC-compatible disc. (墌 pg. 50)
● Regarding the contents recorded on discs
Some files may not be played back depending on the file types and other
factors.
8
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_04DiscInfo.fm]
Masterpage:Right+
MV5SEK_00.book Page 9 Wednesday, August 31, 2005 7:58 PM
DISC INFORMATION
Placing A Disc
Care And Handling Of Discs
Opening the disc tray
Press x (OPEN/CLOSE) to open the disc tray.
How to handle discs
When handling a disc, do not
touch the surface of the disc.
Since discs are made of
plastic, they are easily
damaged. If a disc gets dirty,
dusty, scratched or warped, the
images and sound will not be
picked up correctly, and such a
disc may cause the unit to malfunction.
VHS
REC
DVD
PR
VHS/DVD
VHS
DUBBING
DVD
DV IN
● Pressing the button again closes the disc tray.
● Use the button to open and close the disc tray.
● Do not block the disc tray with your hand while it is opening or closing
as this may result in hardware failure.
● Do not place unplayable discs or any object other than a disc on the
disc tray.
● Do not press down strongly on the disc tray or place any heavy
objects on it.
Discs without cartridges
Place the disc on the disc tray with the
label side facing up. Since disc size
changes depending on the disc to be
played back, be sure to correctly align
the disc with the grooves for its size. If
the disc is not in its groove, it may be
scratched or otherwise damaged. To
insert an 8 cm disc, place it according
to the inner groove.
DVD
DUB
VCR
EN
PULL-OP
DVD
REC
LINK
DV IN
CH
FF
REW
REC
DVD
PAUSE
REMAIN
<< SLOW
REC
>>
MODE
DVD-RAM discs contained in cartridges
Double-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the side
you wish to play back or record facing down. If you insert the disc
with “Side A” facing down, programmes are recorded on the side A.
Single-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the label
side facing up.
9
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
EN
9
Label side
Do not damage the label side, stick paper to or use any adhesives
on its surface.
Recording side
Make sure that discs are not scratched and dirty on the recording
side before use. Scratches and dirt on the recording side of a disc
may hinder proper playback and recording. Also be careful that a
DVD-RAM disc may get scratched or dirt when removed from
cartridge then put back in after use.
Storage
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt adhering
to a disc, wipe with a soft dry cloth, moving
from the centre outwards.
If a disc is difficult to clean, wipe with a cloth
moistened with water. Never use record
cleaners, petrol, alcohol or any anti-static
agents.
CAUTION:
Sometimes during playback, noise may appear or images may
be garbled. This is sometimes due to the disc. (It may not be up
to industry standards.)
These symptoms are caused by the discs, not by the malfunction
of the unit.
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Left0
MV5SEK_00.book Page 10 Wednesday, August 31, 2005 7:58 PM
10 EN INDEX
Front View
A
B
DE
C
VHS
STANDBY/ON
FGHIJKL
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
MN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
O
P
Eject Button (x (EJECT)) 墌 pg. 25
Cassette Loading Slot
VHS Lamp (VHS) 墌 pg. 25
DVD Lamp (DVD) 墌 pg. 24
Open/Close Button (x (OPEN/CLOSE)) 墌 pg. 9
Reverse Search Button (3) (DVD deck) 墌 pg. 47, 54
Rewind Button (3) (VHS deck) 墌 pg. 59
Forward Search Button (5) (DVD deck) 墌 pg. 47, 54
Fast Forward Button (5) (VHS deck) 墌 pg. 59
Stop Button (8) 墌 pg. 24, 25
Disc Tray
Play Button (4) 墌 pg. 24, 25
Pause Button (9) 墌 pg. 24, 59
Record Button (7) 墌 pg. 26, 28
Standby/On Button (STANDBY/ON 1)
S-video Input Connector (S-VIDEO) (DVD deck only)
墌 pg. 42
Video/Audio Input Connectors
(VIDEO/AUDIO ((MONO) L/R)) 墌 pg. 42
Front Display Panel 墌 pg. 14
Q
R
S
TU
Q Infrared Beam Receiving Window
R VHS/DVD Select Button* (VHS/DVD) 墌 pg. 24, 25
* This button will not function during navigation mode or set up mode.
S Dubbing Button (DUBBING) 墌 pg. 38 – 40
Dubbing Direction Buttons (VHS]/}DVD) 墌 pg. 37 –
40
T Channel Buttons (PR +/–) 墌 pg. 26, 28, 41
U DV Input connector (DV IN (i*)) (DVD deck only)
墌 pg. 41
* i (i.Link) refers to the IEEE1394-1995 industry specification and
extensions thereof. The i logo is used for products compliant with the
i.Link standard.
To access covered connectors, push and
open the connector cover.
STANDBY/ON
PUSH-OPEN
S-VIDEO
VIDEO
AUDIO
Rear View
A B
C
D E
F
G
H
I
J
A Region Number Label 墌 pg. 7
B AC Power Cord 墌 pg. 15
C Cooling Fan
● This prevents the temperature from rising inside the unit.
Do not remove it.
● Install the unit so as not to block the area around the fan.
● The cooling fan on the rear of the unit may be activated even if
the unit is turned off in the following cases;
— In the Automatic Satellite Programme Recording standby
mode (墌 pg. 36), slightly before the starting time of PDC
recording (墌 pg. 30)
— If you connect the decoder or the satellite receiver to the [L-2
IN/DECODER] connector and if “L-2 SELECT” is set to
“DECODER” or “SAT VIDEO/RGB”. (墌 pg. 44)
— “JUST CLOCK” is set to “ON” (墌 pg. 88)
(Set “JUST CLOCK” to “OFF” if you mind the noise of the fan.)
D Audio Output Connectors (AUDIO OUTPUT (LEFT/
RIGHT)) 墌 pg. 16, 43
10
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
E Component Video Output Connectors (COMPONENT
VIDEO OUT) (DVD deck only) 墌 pg. 16
● This component video output enables you to watch the images on
the VHS deck in Progressive scan mode, refer to “VHS
Progressive Scan” (墌 pg. 60).
F L-1 Input/Output Connector (L-1 IN/OUT) 墌 pg. 15, 43,
76
G Antenna Input Connector (ANTENNA IN) 墌 pg. 15
H Digital Audio Output Connector
(DIGITAL AUDIO OUT (COAXIAL)) (DVD deck only)
墌 pg. 46, 77
I L-2 Input/Decoder Connector* (L-2 IN/DECODER)
墌 pg. 43, 76
* The decoder function of this unit is not available in the U.K.
J Antenna Output Connector (ANTENNA OUT) 墌 pg. 15
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Right+
MV5SEK_00.book Page 11 Wednesday, August 31, 2005 7:58 PM
INDEX
Remote Control
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
EN
11
N Reverse Search Button (3) (DVD deck) 墌 pg. 47, 54
Rewind Button (3) (VHS deck) 墌 pg. 59
Reverse Slow Button (SLOW –) 墌 pg. 48
O Record Button (7) 墌 pg. 26, 28
P Recording Mode Button (REC MODE) 墌 pg. 26, 28
Remain Button (REMAIN) 墌 pg. 49, 61
Q On-Screen Button (ON SCREEN) 墌 pg. 12, 13, 55
R Display Button (DISPLAY) 墌 pg. 49, 61
S Audio Button (AUDIO) 墌 pg. 50
T Subtitle Button (SUBTITLE) 墌 pg. 49
U TV/DVD Switch 墌 pg. 20
V DVD Standby/On Button (DVD STANDBY/ON 1)
W TV Standby/On Button (TV STANDBY/ON 1) 墌 pg. 75
X TV/Video Input Button (TV/VIDEO) 墌 pg. 61, 63
Y TV Volume Buttons (TV % +/–) 墌 pg. 75
Z Channel Buttons (PR +/–) 墌 pg. 26, 28, 41
Page Buttons 墌 pg. 66, 70, 71
a Memo Button (MEMO) 墌 pg. 66, 70
Mark Button (MARK) 墌 pg. 49
b Timer Button (TIMER #) 墌 pg. 29, 31, 32
c Automatic Satellite Programme Recording Button (SAT
#) 墌 pg. 36
d Navigation Button (NAVIGATION) 墌 pg. 65
e Enter Button (ENTER) 墌 pg. 20
f Return Button (RETURN) 墌 pg. 29, 57
g Forward Skip Button (6) 墌 pg. 47, 49, 54
Next Button 墌 pg. 50
h Forward Search Button (5) (DVD deck) 墌 pg. 47, 54
Fast Forward Button (5) (VHS deck) 墌 pg. 59
Forward Slow Button (SLOW +) 墌 pg. 48
i Play Button (4) 墌 pg. 24, 25
j Pause Button (9) 墌 pg. 24, 59
k Stop Button (8) 墌 pg. 24, 25
Clear Button (CLEAR) 墌 pg. 58
l Skip Search Button (
) 墌 pg. 48, 54
m Angle Button (ANGLE) (DVD deck only) 墌 pg. 49
Live Check Button (LIVE CHECK) 墌 pg. 54
n One Touch Replay Button (
) 墌 pg. 54
o Set Up Button (SET UP) 墌 pg. 20
p Progressive Scan Button (PROGRESSIVE SCAN)
墌 pg. 60, 80
How To Use
The remote control can operate most of your unit’s functions, as
well as basic functions of TV sets of JVC and other brands.
(墌 pg. 74)
● Point the remote control toward the receiving window.
● The maximum operating distance of the remote control is about
8 m.
NOTES:
A Open/Close Button (x (OPEN/CLOSE)) 墌 pg. 9, 24
B Eject Button (x (EJECT)) 墌 pg. 25
C VHS Button* 墌 pg. 25
* This button will not function during navigation mode or set up mode.
D DVD Button* 墌 pg. 24
● When inserting the batteries, be sure to insert in the correct
directions as indicated under the battery cover.
● If the remote control doesn’t work properly, remove its batteries,
wait for approximately 5 minutes, replace the batteries and then try
operating the unit again.
* This button will not function during navigation mode or set up mode.
E Number Buttons 墌 pg. 26, 28, 29, 67
F Cancel Button (CANCEL) 墌 pg. 58
Counter Reset Button (0000) 墌 pg. 63
G Auxiliary Button (AUX)
H VIDEO Plus+ Button 墌 pg. 29
I Programming Button (PROG) 墌 pg. 31, 32, 34
J Top Menu Button (TOP MENU) 墌 pg. 47
K rt w e Buttons 墌 pg. 20
L Menu Button (MENU) 墌 pg. 47
M Reverse Skip Button (2) 墌 pg. 47, 49, 54
Previous Button 墌 pg. 50
11
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Left+
MV5SEK_00.book Page 12 Wednesday, August 31, 2005 7:58 PM
12 EN INDEX
On-Screen Display (DVD deck)
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the remote control is pressed, various operational indicators appear on the
TV screen. To clear the operational indicators, press ON SCREEN twice.
When using Live Memory playback
When playing back a recorded title
A
B
C
DVD-VIDEO
LPCM 2ch
D
E
TITLE1
F
G
A
B
DVD-RW/VR
SP
0:01:23
D
E
F
STEREO
PR 95
G
H
Disc type
Recording mode
Current time
Recording point
Current status (recording)
Elapsed recording time
Audio mode
Recording channel number
REC QUALITY
PR 10
F
G
E
Disc type
Current time
Bar meter for recording/playback
Recording mode
Current playback time/Elapsed recording time
Audio mode
Recording channel number
B
DVD-RW/VR
TITLE12
SP
EACH
C
A
B
C
D
E
F
G
When pressing REC MODE
(Appears for eight seconds.)
STEREO
A
18:04
CHAPTER1
18:36
CHAPTER1
0:13:34
DV Dubbing
When capturing images from the external DV
equipment
C
EACH
TITLE2
LP
D
C
A
B
C
D
E
F
G
TITLE14
0:12:27
EACH
Disc type
Audio mode
Current status (playback)
Playback title number
Playback chapter number
Current playback point
Elapsed playing time
XP:
SP:
LP :
EP:
FR:
TITLE2
0:01:08
When recording
A
B
C
D
E
F
G
H
B
DVD-RAM
CHAPTER1
EACH
A
B
C
D
E
F
G
A
D
--:--
CHAPTER--
0:00:00
E
L
R
F
DV
G
Disc type
Current time
Current recording point
Current status (recording)
Elapsed recording time
Sound mode
Recording channel (DV input)
DV Dubbing Controller
DV DUBBING
RECORDABLE TIME
1:00
2:00
4:01
6:03
2:31 (FR150)
DV
A
A
B
A Recording mode
B Remaining disc time for each recording speed
AUDIO 1
1
DV
B
2
C
A Displays when remote control is set to DV control mode.
B Auto capture button
C Sound monitor switch
During Instant Timer Recording (ITR)
SP
TITLE13
CHAPTER1
ITR
0:13
A
A Record remaining time
12
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Right+
MV5SEK_00.book Page 13 Wednesday, August 31, 2005 7:58 PM
INDEX
EN
13
On-Screen Display (VHS deck)
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the remote control is pressed, various operational indicators appear on the
TV screen. To clear the operational indicators, press ON SCREEN twice.
H Tape Position Indicator
The tape position indicator
appears on the TV screen
when you press 3 or 5
from the Stop mode or perform
an Index Search. (墌 pg. 59)
The position of “q” in relation to
“0” (beginning) or “+” (end)
shows you where you are on
the tape.
NOTE:
Beginning
End
Depending on the type of tape
being used, the tape position
indicator may not appear correctly.
A
B
C
D
E
F
G
Operation Mode Indicators
Tape Speed (SP/LP)
Tape Direction
Index Mark Indicator (MARK) 墌 pg. 28
Counter Display
Tape Remaining Time Indicator 墌 pg. 64
Audio Mode Display 墌 pg. 60
I VPS/PDC Indicator* 墌 pg. 30
* VPS (Video Programme System) recording is not currently available in the
U.K. and not possible with this unit.
J
K
L
M
Type of Broadcast 墌 pg. 64
Current Day/Month/Year
Clock Display
Channel Position Number and Station Name/Auxiliary
Input Indicator (L-1, L-2, F-1 or SAT*)
* When “L-2 SELECT” is set to “SAT VIDEO/RGB” (墌 pg. 45), “SAT”
appears instead of “L-2”.
N “Cassette Loaded” Mark
13
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Left+
MV5SEK_00.book Page 14 Wednesday, August 31, 2005 7:58 PM
14 EN INDEX
Front Display Panel
AB
C
D
H
I
O
P
Q
L
M
N
R
S
T
U
J Track/Chapter Indicator (TRK/CHAP)
)
Lights when video mode is selected by pressing TV/VIDEO.
“TRK” or “CHAP” lights depending on a disc loaded while the 3rd
and 4th digits from the left of the Multi Display (R) indicate the
numbers explained below.
“TRK”:
Total number of tracks or track number being played
back are displayed on the Multi Display.
“CHAP”: Chapter number being played back are displayed on the
Multi Display.
B Disc Type Indicator
When a disc is loaded, the type of the disc is indicated.
Disc Status Indicator
When a disc is running, the disc marks rotate.
During High-Speed Search: Rotate faster than normal playback.
During Slow Motion:
Rotate slower than normal playback.
While recording/dubbing:
Inner red ring lights. During Timer
Recording, inner red ring slowly
blinks.
While playing back:
Outside ring lights.
While paused:
Disc marks blink when either
recording or playing back.
While stopped:
Disc marks all light.
While resume stopped:
Disc marks all blink.
While the disc tray opened:
Disc marks all light out.
No disc on the disc tray:
Disc marks all light out.
VR Mode Indicator (VR) 墌 pg. 7, 89
Lights when a DVD-RW disc is formatted in VR mode.
C VPS/PDC Indicator*墌 pg. 29 – 30
* VPS (Video Programme System) recording is not currently available in
the U.K. and not possible with this unit.
D Linear PCM Indicator (LPCM)
Lights when “XP MODE REC AUDIO” is set to “LINEAR PCM”
(墌 pg. 79) for recording with DVD-RAM, DVD-R and DVD-RW
discs, and when Linear PCM audio is played.
E Cassette Loaded Mark (
)
Indicates the present of a cassette in the VHS deck.
Lights when a cassette is loaded into the VHS deck. Blinks when
the end of the tape has been reached during timer recording or
when the unit is in timer recording standby mode with a cassette
without record safety tab inserted.
F VHS Timer Indicator (
K
J
LPCM
FR
XP SP LP EP
VR +-RW VCD
DVD -RAM
VHS
A Video Indicator (
EF G
)
K Random/Programme Playback Mode Indicator (RND/
PRGM) 墌 pg. 58
“RND”:
Lights when Random Playback mode is set.
“PRGM”: Lights when Programme Playback mode is set.
/1/A–B) 墌 pg. 56
L Repeat Mode Indicator (
Select Repeat Playback mode on the on-screen bar.
“
”:
Whole disc is played back repeatedly.
“
1”:
A single title/chapter/track is played back repeatedly.
“
A–B”: The selected part (A–B) is played back repeatedly.
No display: Repeat Playback mode is off.
M
Indicator 墌 pg. 32
Lights when a disc set up for On-Disc Timer Programming is loaded.
N DVD Timer Indicator (
)
Lights when the DVD deck is in the timer recording standby mode or
when timer recording is in progress.
Blinks when rapidly when TIMER# is pressed under the following
conditions:
● Clock is not set.
● Timer programming has not been set.
● Disc is not loaded.
● Timer recording standby mode with a non recordable disc.
O VHS Indicator 墌 pg. 25
Lights when VHS mode has been selected, during recording or
when tapes recorded in VHS format are played back.
P Video Output Indicator (
) 墌 pg. 80
No display: Indicates that interlace mode is engaged.
:
Indicates that progressive mode is engaged.
(Example)
lights when video output mode is in progressive
mode.
Lights when the VHS deck is in the timer recording standby mode or
when timer recording is in progress.
Blinks rapidly when TIMER# is pressed under the following
conditions:
● Clock is not set.
● Timer programming has not been set.
● Cassette is not loaded.
● Timer recording standby mode with a cassette without safety tab
inserted.
● Tape end is reached during time recording.
Q Group/Title Number Display
R Track/Chapter Number Display
S Remaining Time/Elapsed Time Indicator 墌 pg. 49, 61
Blinks when recording mode is being set.
While “FR” lights up, the left 3 digits of the Multi Display (Q R)
indicate setting values ranging from “60” to “480”. After the value
has been set, only “FR” lights.
T Remaining Time/Elapsed Time Display 墌 pg. 49, 61
U Multi Display
G Recording Mode Indicator (XP/SP/LP/EP/FR) 墌 pg. 27
H Group/Title Indicator (GRP/TITLE)
“GRP” or “TITLE” lights depending on a disc loaded while the left 2
digits of the Multi Display (Q) indicate the numbers explained below.
“GRP”:
Total number of groups or group number being played
back are displayed on the Multi Display.
“TITLE”: Total number of titles or title number being played back
are displayed on the Multi Display.
Lights when remaining time of DVD-RAM, DVD-R and DVD-RW
discs is displayed, and lights out when elapsed time is displayed.
The right 6 digits of the Multi Display (T) indicate elapsed or
remaining time of each track.
No display: Indicates elapsed time of the disc.
Displayed: Indicates remaining time of the disc.
Displays clock, received channel, elapsed time, and remaining time.
Also displays status of the unit (NO DISC/OPEN/CLOSE/
READING).
I Channel/Recording Mode Indicator
Indicates the channel received. Or the recording mode (SP, LP) of
the VHS deck. (墌 pg. 28)
14
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Right0
MV5SEK_00.book Page 15 Wednesday, August 31, 2005 7:58 PM
GET OVER IT! – CONNECTIONS –
15
Composite Connection
Connections
It’s essential that your unit be properly connected.
ATTENTION:
Your TV must have a 21-pin AV input connector (SCART)
for the connection to the unit.
THESE STEPS MUST BE COMPLETED BEFORE ANY
VIDEO OPERATION CAN BE PERFORMED.
1
2
EN
Place the unit on a stable, horizontal surface.
Connect the unit to a TV depending on the TV and
cables you use.
● (墌 pg. 15, “Composite Connection”)
● (墌 pg. 16, “Component Video Connection (DVD deck only)”)
Aerial connector
Back of TV
RF cable
(provided)
TV aerial cable
21-pin SCART connector
4
Disconnect the TV aerial cable from the TV.
Connect the TV aerial cable to the [ANTENNA IN]
connector on the rear panel of the unit.
Connect the [ANTENNA OUT] connector on the rear
panel of the unit and the TV’s aerial connector with
the provided RF cable.
Connect the [L-1 IN/OUT] connector on the rear
panel of the unit and the TV’s 21-pin SCART
connector with a provided 21-pin SCART cable.
● The [L-1 IN/OUT] connector accepts and delivers either a
composite signal (regular video signal), Y/C signal or
RGB signal.
● Set your TV to the VIDEO (or AV), Y/C, or RGB mode
according to the type of your TV’s SCART connector.
● Select an appropriate option of “L-1 OUTPUT” as follows
(墌 pg. 44):
When your TV’s SCART
connector accepts:
Set “L-1 OUTPUT” to:
Composite video signals
“SCART VIDEO”
Y/C signal (separated
luminance (brightness) and
chrominance (colour)
signals)
“SCART S-VIDEO”
RGB signal
“SCART RGB”
5
21-pin SCART cable
(provided)
AC power cord
1
2
3
Plug the end of the AC power cord into an AC outlet.
● “LOADING” blinks on the front display panel when the AC
plug of the power cord is connected into a AC outlet and
no operation will be done for approximately 50 seconds.
This is not a malfunction.
ANTENNA IN
After connection is completed, perform “Auto Set Up” on
page 17.
Back of unit
AC outlet
15
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
L-1 IN/OUT
ANTENNA OUT
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Left+
MV5SEK_00.book Page 16 Wednesday, August 31, 2005 7:58 PM
16 EN GET OVER IT! – CONNECTIONS –
Component Video Connection (DVD deck only)
ATTENTION:
Your TV also must have a component video input
connectors for the connection to the unit.
1
2
Back of TV
3
4
Component video input connectors
RF cable
(provided)
Connect the unit’s [COMPONENT VIDEO OUT]
connectors to the TV’s component video input
connectors.
Connect the unit’s [AUDIO OUT] connectors to the
TV’s AUDIO input connectors.
● You can obtain high-quality component video pictures.
● If your TV is not stereo-capable, use the unit’s [AUDIO
OUT] connectors to connect to an audio amplifier for Hi-Fi
stereo sound reproduction.
● By using the component video connection, you can view
the images in the progressive mode. For switching to the
progressive mode, refer to “Scan Mode Set” (墌 pg. 80).
Aerial connector
Component video cable
(not provided)
Perform 1 – 3 in “Composite Connection”
(墌 pg. 15).
TV aerial cable
Plug the end of the AC power cord into an AC outlet.
● “LOADING” blinks on the front display panel when the AC
plug of the power cord is connected into an AC outlet and
no operation will be done for approximately 50 seconds.
This is not a malfunction.
After connection is completed, perform “Auto Set Up” on
page 17.
ANTENNA IN
AC power cord
Back of unit
AC outlet
COMPONENT VIDEO OUT
ANTENNA OUT
16
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Right0
MV5SEK_00.book Page 17 Wednesday, August 31, 2005 7:58 PM
INITIAL SETTINGS
Auto Set Up
Auto Channel Set/Auto Clock Set/Auto Guide Program
Number Set
After the 1 button on the unit or remote control is pressed for
the first time to turn on the unit, the Auto Set Up function sets the
tuner channels, clock and Guide Program numbers
automatically.
EN
17
ATTENTION:
Once you have performed Auto Set Up, even if the unit’s memory
backup has expired, all the stored stations and their Guide
Program numbers remain in the unit’s memory and the unit will
not perform Auto Set Up again. The unit only performs Auto
Clock Set when the unit is turned on.
If you have moved to a different area, perform each setting as
required.
● Tuner setting (墌 pg. 84)
● Clock setting (墌 pg. 88)
If a new station starts broadcasting in your area, perform tunesr
setting. (墌 pg. 84)
NOTES:
VHS
DVD
● In areas where no TV station transmits a PDC (Programme Delivery
Control) signal, the unit can perform neither Auto Clock Set nor Auto
Guide Program Number Set.
● If there is a power cut, or if you press 1 or SET UP while Auto Set
Up is in progress, Auto Set Up will be interrupted; be sure to turn off
the unit power once and try again from step 1.
● Auto Clock Set may not function properly depending on the reception
condition.
After “Auto Set Up” is completed, perform “Monitor Set (DVD
Deck Only)” on page 21.
ENTER
SET UP
Before starting, make sure of the following:
●
●
●
●
The TV aerial cable should be connected to the unit.
The unit’s AC power cord should be connected to a AC outlet.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
1 Press 1 to turn on the unit. The AUTO SET/T-V LINK display
appears on the TV screen.
2 Press rt to select “AUTO
SET”, then press ENTER. The
AUTO SET screen will appear,
and the unit automatically
performs Auto Channel Set.
INITIAL SET UP
INITIAL SET UP / CHANNEL SET
AUTO SET
T-V LINK
● When Auto Channel Set is
completed, “PLEASE WAIT” will
OK
SET UP
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
be displayed for about 90
SELECT
EXIT
seconds, since channel data is
exchanged between the DVD
deck and the VHS deck. No operation will be done during this time.
ATTENTION:
● When you have connected the
unit to a TV offering T-V Link via a
fully-wired 21-pin SCART cable
(墌 pg. 15) and the TV is turned
on, the unit automatically
performs the Preset Download
(墌 pg. 18) even if you select
“AUTO SET” for Auto Set Up
function.
INITIAL SET UP
INITIAL SET UP / CHANNEL SET
AUTO SET
AUTO SET
T-V LINK
PLEASE WAIT...
CANCEL
SET UP
EXIT
17
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
OK
SELECT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Left+
MV5SEK_00.book Page 18 Wednesday, August 31, 2005 7:58 PM
18
EN
INITIAL SETTINGS
Preset Download
Auto Channel Set By Downloading From TV/Auto
Clock Set/Auto Guide Program Number Set
ATTENTION:
You can use this function only with a TV offering T-V Link, etc.* Be
sure to use a fully-wired 21-pin SCART cable.
* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART
cable. The degree of compatibility and available functions may differ by
system.
VHS
DVD
If you have connected the unit to your TV via a 21-pin SCART
cable (墌 pg. 15), the unit will automatically perform Preset
Download instead of the Auto Set Up in step 2 on page 17. After
downloading, the unit sets the clock and Guide Program numbers
automatically.
● Slide the TV/DVD switch to DVD.
1 Press 1 to turn on the unit. The AUTO SET/T-V LINK display
appears on the TV screen.
2 Press rt to select “T-V LINK” and press ENTER. The T-V
LINK screen will appear, and the unit automatically performs Auto
Channel Set.
● When Auto Channel Set is
completed, “PLEASE WAIT” will
be displayed for about 90
seconds, since channel data is
exchanged between the DVD
deck and the VHS deck. No
operation will be done during this
time.
Preset positions on the front display
panel increase from “PR 1”; do NOT
press any button on the unit or
remote control until the front display
panel shows clock time, “PR 1” or “–
–:– –” as illustrated on page 19.
AUTO SET
T-V LINK
SET UP
OK
SELECT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
INITIAL SET UP
INITIAL SET UP / CHANNEL SET
AUTO SET
T-V LINK
PLEASE WAIT...
SET UP
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
● For details, refer to the instruction
SELECT
EXIT
manual of your TV.
● In the area where no TV station transmits a PDC (Programme
Delivery Control) signal, the unit can perform neither Auto Clock Set
nor Auto Guide Program Number Set.
● If there is a power cut, or if you press 1 or SET UP while
downloading or set up is in progress, it will be interrupted; be sure to
turn off the unit power once and try again from the beginning.
● Auto Clock Set may not function properly depending on the reception
condition.
● On this unit, the characters available for station names (ID) are A–Z,
0–9, –, f, + and I (space). Some names of downloaded stations
may differ from those of your TV. (墌 pg. 87)
ENTER
SET UP
18
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
INITIAL SET UP / CHANNEL SET
EXIT
ATTENTION:
NOTES:
INITIAL SET UP
After “Preset Download” is completed, perform “Monitor Set
(DVD Deck Only)” on page 21.
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Right+
MV5SEK_00.book Page 19 Wednesday, August 31, 2005 7:58 PM
INITIAL SETTINGS
Results Of Auto Set Up/Preset Download Appearing
On The Front Display Panel
If both Auto Channel Set and
Auto Clock Set have been
performed successfully, the
correct current time is displayed.
Turn on the TV and select its AV mode, then make sure that all
necessary stations have been stored in the unit’s memory by using
the PR +/– button(s).
● If station names (ID – 墌 pg. 97) have also been stored in the unit’s
memory, the station name will be displayed at the top right corner of
the TV screen for about 5 seconds when the unit is tuned to a
different station.
● If you want to set the tuner manually such as to add or skip channels,
to change channel positions, or to set or change station names, see
pages 85 – 87.
If Auto Channel Set has
succeeded but Auto Clock Set
has not, “PR 1” (channel
position) is displayed.
OR
If both Auto Channel Set and Auto Clock Set have failed,
“– –:– –” is displayed.
A Turn on the TV and select its AV mode, then make sure that all
necessary stations have been stored in the unit’s memory by using
the PR +/– button(s).
● If station names (ID – 墌 pg. 97) have also been stored in the unit’s
memory, the station name will be displayed at the top right corner of
the TV screen for about 5 seconds when the unit is tuned to a
different station.
● If you want to set the tuner manually such as to add or skip channels,
to change channel positions, or to set or change station names, see
pages 85 – 87.
EN
19
INFORMATION
Just Clock
Your unit is equipped with the Just Clock function which provides
accurate time keeping through automatic adjustments at regular
intervals, by reading data from a PDC signal. If you want to take
advantage of this function, simply set it to “ON”. (墌 pg. 88)
If you have any difficulty with the above procedures call the JVC
Customer Service Hot Line on 0870 330 5000.
T-V Link Functions (DVD Deck Only)
When you connect the unit to your TV via a fully-wired 21-pin
SCART cable (墌 pg. 15), the following functions are available. You
can use these functions only with a TV offering T-V Link, etc.*
For details, refer to the instruction manual of your TV.
* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART
cable. The degree of compatibility and available functions may differ by
system.
TV Auto Power On
The TV will turn on and be set to its AV mode automatically
whenever you start playback.
For details, refer to the instruction manual of your TV.
Unit Auto Standby
You can use your TV’s remote control to turn off the unit.
For details, refer to the instruction manual of your TV.
Direct Rec
You can easily start recording the programme that you are
watching on your TV. When you use this function, set “DIRECT
REC” to “ON”. (墌 pg. 79)
B Perform “Clock Set” on page 88.
ATTENTION:
After making sure the cables are connected properly, turn off the unit’s
power once, then turn the unit’s power back on again.
Perform “Auto Set Up” on page 17 or “Preset Download” on page 18
again.
IMPORTANT:
● To check if the Guide Program numbers have been set correctly,
perform the VIDEO Plus+ Timer Programming. (墌 pg. 29)
● In certain reception conditions, station names may not be stored
correctly, and auto Guide Program Number Set may not work
properly. If the Guide Program numbers are not set properly when
you timer-record a TV programme using the VIDEO Plus+ system,
the unit will record a TV programme of a different station. When
programming the timer using the VIDEO Plus+ system, be sure to
check the desired channel is selected correctly. (墌 pg. 29)
● Your unit memorises all detected stations even if reception of some of
them is poor. You can delete those stations with an unacceptable
picture. (墌 pg. 86, “Delete A Channel”)
19
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Left+
MV5SEK_00.book Page 20 Wednesday, August 31, 2005 7:58 PM
20
EN
INITIAL SETTINGS
Menu/Audio/Subtitle Language Set (DVD Deck Only)
Language
Some DVD discs contain the DVD menu display, audio and
subtitles in multiple languages. With these discs, you can set the
default language as you like.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
● The procedure shows how to set “MENU LANGUAGE” as an
example.
1 Press DVD so that the DVD lamp lights up on the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “DVD SET UP”, then press t.
4 Press w e to select
DVD SET UP
VHS
DVD
“LANGUAGE SET”, then press t.
5 Press rt to select “MENU
LANGUAGE”, then press ENTER.
6 Press rt to select your
desired language, then press
ENTER.
● See “Language Code List”
(墌 pg. 96).
FUNCTION SET UP
LANGUAGE SET
INITIAL SET UP
AUDIO OUTPUT
UTILITY
MENU LANGUAGE
ENGLISH
AUDIO LANGUAGE
ENGLISH
SUBTITLE
SET UP
EXIT
OFF
OK
SELECT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
7 Press SET UP to complete the setting.
NOTE:
ENTER
When the selected language is not available on the disc, the disc’s
default menu language is played back.
SET UP
20
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_05Name.fm]
Masterpage:Right+
MV5SEK_00.book Page 21 Wednesday, August 31, 2005 7:58 PM
INITIAL SETTINGS
Monitor Set (DVD Deck Only)
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
EN
21
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “FUNCTION SET UP”, then press t.
3 Press w e to select “VIDEO
DVD SET UP
IN/OUT”, then press t.
FUNCTION SET UP
VIDEO IN/OUT RECORDING SET
4 Press rt to select
MONITOR TYPE
“MONITOR TYPE”, then press
ENTER.
L-1 INPUT
VIDEO
L-1 OUTPUT
option, then press ENTER.
6 Press SET UP to complete the
L-2 SELECT
SET UP
EXIT
OTHERS
4:3LB
VIDEO
F-1 INPUT
5 Press rt to select the desired
INITIAL SET UP
DISPLAY SET
OK
SELECT
SCART VIDEO
VIDEO/RGB
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
setting.
VHS
DVD
* The boldface settings below indicate the settings at your
purchase.
8 MONITOR TYPE — 4:3 LB / 4:3 PS / 16:9 AUTO / 16:9 FIX
4:3 LB (Letter Box conversion): Select this when the aspect ratio of
your TV is 4:3 (conventional TV). While viewing a wide screen
picture, the black bars appear on the top and the bottom of the
screen.
4:3 PS (Pan&Scan): Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide screen picture, the
black bars do not appear; however, the left and right edges of the
pictures will not be shown on the screen.
16:9 AUTO (Wide television conversion): Select this when the
aspect ratio of your TV is 16:9 (wide TV).
16:9 FIX (Wide television conversion): Select this when the aspect
ratio of your TV is fixed to 16:9 (wide TV). The unit automatically
adjusts the screen width of the output signal correctly when
playing back a picture whose aspect ratio is 4:3.
ENTER
SET UP
Pan&Scan/Letter Box
In general, DVD VIDEO disc are produced for a wide-screen TV
with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect ratio.
There are two styles to display the image, “Pan&Scan” (PS) and
“Letter Box” (LB).
Pan&Scan
The right and left side of the image are cut off.
The image fills the screen.
● The picture will be shown in the “4:3 LB” mode
depending on the disc even if the “4:3 PS” mode
is selected.
Letter Box
Black bands appear at the top and bottom of
the image. The image itself appears in 16:9
aspect ratio.
21
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_06TocOperation.fm]
MV5SEK_00.book Page 22 Wednesday, August 31, 2005 7:58 PM
Masterpage:Left0
Playback
DVD ..............................................................................................................................24
Playback of the programme being recorded (Live Memory playback).......................51
How to search and manage the DVD titles (Navigation) ..........................................65
VHS ...............................................................................................................................25
Recording
DVD ............................................................ 26
About recording mode............................ 27
VHS ............................................................. 28
About recording mode............................ 28
hat do you w
22
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_06TocOperation.fm]
Masterpage:Right0
MV5SEK_00.book Page 23 Wednesday, August 31, 2005 7:58 PM
Timer
recording
Using PlusCode number........................................... 29
Setting timer manually............................................. 31
How to record a satellite programme ...................... 36
Dubbing
From VHS to DVD .................................................................................................. 37
From DVD to VHS .................................................................................................. 39
Dubbing from a digital equipment like a camcorder............................................... 41
u want to do?
23
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_07Basic PlayRec.fm]
Masterpage:Left0
MV5SEK_00.book Page 24 Wednesday, August 31, 2005 7:58 PM
24
EN
BASIC PLAYBACK
To play back an MP3/JPEG disc, see “Playback With MP3/
JPEG Navigation” (墌 pg. 72).
Basic Playback (DVD)
1 Load a disc.
● For details, refer to “Placing A Disc” (墌 pg. 9).
● Playback begins automatically if an auto-playback DVD
disc is loaded.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
VHS/DVD on the unit repeatedly
2 Press
or DVD on the remote control so that
the DVD lamp lights up on the unit.
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
DVD lamp
ENTER
3 Press 4 to start playback.
● If you load a DVD disc whose region code does not match
the unit, “REGION CODE ERROR” appears on the TV
screen. For details, refer to “Region Number” (墌 pg. 7).
● With Video CD discs with PBC control or some DVD
discs, the menu display may appear on the TV screen
after starting playback. In this case, select an item which
you want to play back from the menu. Otherwise, the
playback cannot go forward. Refer to “Playback Control
(PBC) Function” (墌 pg. 50) or “Locating A Desired Scene
Using The DVD Menu” (墌 pg. 47).
● The Library Database DVD Navi also enables you to
search and select the desired titles. (墌 pg. 66)
4 Press 9 to pause playback.
● To resume normal playback, press 4.
5 Press 8 to stop playback.
ATTENTION:
● It takes approximately 30 seconds to read a disc
depending on the type and condition of the disc since
this unit is multi-disc compatible (DVD-RAM, DVD-RW,
DVD-R). It may even take several minutes when a disc
is dirty, scratched or warped.
● It may take a few seconds to start playback. This is not
a malfunction.
● Forward/reverse high-speed search and other
operations cannot be performed while playback is
stopped.
24Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
● When a recordable disc is played, playback stops and a
programme received with the unit’s tuner resumes on the
TV screen.
● When a playback-only disc is played, playback stops and
the TV screen becomes all blue when you press 8.
Pressing 8 again resumes a programme received with
the unit’s tuner.
● If x (OPEN/CLOSE) is pressed during playback,
playback stops, then the disc tray opens.
eject the disc, press x (OPEN/
6 ToCLOSE).
NOTE:
When the Library Database DVD Navi screen appears,
choose a thumbnail image of the desired title on the TV
screen, then press ENTER. (墌 pg. 66)
Filename [MV5SEK_07Basic PlayRec.fm]
Masterpage:Right+
MV5SEK_00.book Page 25 Wednesday, August 31, 2005 7:58 PM
BASIC PLAYBACK
Basic Playback (VHS)
● Make sure the window side is up, the rear label side is
facing you and the arrow on the front of the cassette is
pointed toward the unit.
● Do not apply too much pressure when inserting.
● If the record safety tab has been removed, playback
begins automatically.
● The unit’s power comes on automatically and the counter
is reset to 0:00:00.
VHS
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
VHS lamp
25
1 Load a cassette.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
STANDBY/ON
EN
VHS/DVD on the unit repeatedly
2 Press
or VHS on the remote control so that
the VHS lamp lights up on the unit.
3 Press 4 to start playback.
4 Press 9 to pause playback.
● To resume normal playback, press 4.
5 Press 8 to stop playback.
eject the cassette, press x
6 To(EJECT).
Usable cassettes
Full-Size VHS
T-30 (ST-30**) / T-60 (ST-60**) / T-90 / T-120 (ST-120**) /
T-160 (ST-160**) / ST-210**
Compact VHS*
TC-20 (ST-C20**)
TC-30 (ST-C30**)
TC-40 (ST-C40**)
* Compact VHS
camcorder recordings
can be played on this
unit. Simply place the
recorded cassette into a VHS Cassette Adapter and it
can be used just like any full-sized VHS cassette.
** This unit can record on regular VHS and Super VHS
cassettes.
However, it will record regular VHS signals only.
• S-VHS recording is not possible with this unit.
● This unit is equipped with SQPB (S-VHS QUASI
PLAYBACK) that lets you watch tapes recorded in the
S-VHS format with regular VHS resolution.
• SQPB does not deliver Super VHS resolution.
25Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_07Basic PlayRec.fm]
Masterpage:Left0
MV5SEK_00.book Page 26 Wednesday, August 31, 2005 7:58 PM
26
EN
BASIC RECORDING
Basic Recording (DVD)
1 Load a recordable disc.
● For details, refer to “Placing A Disc” (墌 pg. 9).
VHS/DVD on the unit repeatedly
2 Press
or DVD on the remote control so that
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
the DVD lamp lights up on the unit.
ATTENTION:
It is not possible to record programmes on a DVD-R disc
which has already been finalised.
VHS
STANDBY/ON
REC
DVD
VIDEO
● If you record the programmes received by the satellite
receiver ...
1) Select “L-2” by pressing PR +/–.
2) Set the satellite receiver to the appropriate channel.
PR
VHS/DVD
S-VIDEO
PR +/– or the number buttons to
3 Press
select the channel you wish to record.
AUDIO
VHS
DUBBING
DVD
DV IN
DVD lamp
REC MODE repeatedly to select
4 Press
the recording mode, then press
ENTER.
● Each time you press REC MODE, the recording mode
changes as follows:
XP ] SP ] LP ] EP ] FR60–FR360* ] FR420,
FR480 ] (Back to the beginning)
* The value is selectable from 1 to 6 hours in 5-minutes interval
by pressing w e repeatedly after selecting “FR60–FR360”. To
change the value in 30-minutes interval, press and hold w e.
● For details on the recording mode, see “Recording Mode”
(墌 pg. 27).
we
7 on the unit to start recording.
5 Press
Or while holding 7, press 4 on the
remote control.
6 Press 9 to pause recording.
● To resume recording, press 4.
7 Press 8 to stop recording.
● It takes about 10 seconds to end the writing session when
you stop recording.
26Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_07Basic PlayRec.fm]
Masterpage:Right+
MV5SEK_00.book Page 27 Wednesday, August 31, 2005 7:58 PM
BASIC RECORDING
NOTES:
● It is recommended to format a DVD-RAM disc before use if
you use the disc on this unit for the first time.
● When using a brand-new DVD-RW disc, format the disc
either in VR mode or in Video mode. (墌 pg. 89)
● Recordings made on DVD-R/RW disc must be finalised to
play back on other DVD players. Perform “Finalise A Disc
(DVD Deck Only)” (墌 pg. 90).
● You can record up to 99 programmes and 999 play lists on
each disc.
● Some programmes can only be recorded one time.
● When recording is started, an index of the first part of
recording is automatically recorded. (墌 pg. 65) To record
satellite programmes, refer to page 36. To delete the index,
refer to page 67.
● Recording sometimes may stop or cannot be performed even
if there is enough available capacity remaining on the disc.
EN
27
Recording Mode
MPEG2 format is used as recording format. As a guide for
picture quality, the “bps” unit is used to represent how much
data can be recorded per second. The larger this value is,
the better the picture quality becomes but more capacity is
required for the recording. Select XP or SP for programmes
where quick movement occurs, such as sports
programmes, and LP or EP for talk shows, etc. with
relatively less movement.
The recording modes for a 4.7 GB disc are set as follows:
Recording
mode
Recording amount
(approx.)
Maximum recording
time (approx.)
XP
9.6 Mbps
1 hour
SP
5 Mbps
2 hours
LP
2.5 Mbps
4 hours
EP
1.6 Mbps
6 hours
FR60–
FR360*
(墌 pg. 62)
The amount varies
depending on the
selected time.
1 – 6 hours
FR420*
7 hours
FR480*
8 hours
* For details on FR mode, refer to “Free Rate Function” (墌 pg. 62).
Recording Resume Function
If there is a power outage during recording, Instant Timer
Recording (ITR) (墌 pg. 61) or timer recording (墌 pg. 29,
31), the recording will resume automatically when power is
restored to the unit unless the unit’s memory backup has
expired.
27Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_07Basic PlayRec.fm]
Masterpage:Left+
MV5SEK_00.book Page 28 Wednesday, August 31, 2005 7:58 PM
28
EN
BASIC RECORDING
Basic Recording (VHS)
PR +/– or the number buttons to
3 Press
select the channel you wish to record.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
VHS
STANDBY/ON
● If you record the programmes received by the satellite
receiver ...
1) Select “L-2” by pressing PR +/–.
2) Set the satellite receiver to the appropriate channel.
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
REC MODE repeatedly to set the
4 Press
recording mode.
DV IN
VHS lamp
7 on the unit to start recording.
5 Press
Or while holding 7, press 4 on the
remote control.
● If “SUPERIMPOSE” is set to “AUTO” (墌 pg. 79), “MARK”
blinks on the screen while an index code is being marked.
● B.E.S.T. takes place at the beginning of both the first SP
and the first LP recording after inserting the cassette.
(墌 pg. 64)
● If “DIRECT REC” is set to “ON”, the programme that
appears on the TV screen will be recorded. (墌 pg. 79)
6 Press 9 to pause recording.
● You can select channel during the Record Pause mode.
● To resume recording, press 4.
7 Press 8 to stop recording.
Recording Mode
Recording
mode
a cassette with the record safety
1 Load
tab intact.
● The unit’s power comes on automatically and the counter
is reset to 0:00:00.
VHS/DVD on the unit repeatedly
2 Press
or VHS on the remote control so that
the VHS lamp lights up on the unit.
28Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Maximum
recording
time
(approx.)
Use
SP
3 hours
Select when the picture
quality is important.
LP
6 hours
Select when the time is
important. You can record 2
times longer than SP mode.
Recording Resume Function
If there is a power outage during recording, Instant Timer
Recording (ITR) (墌 pg. 63) or timer recording (墌 pg. 29,
31), the recording will resume automatically when power is
restored to the unit unless the unit’s memory backup has
expired.
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Right0
MV5SEK_00.book Page 29 Wednesday, August 31, 2005 7:58 PM
TIMER RECORDING
VIDEO Plus+ Timer Programming
perform timer programming.
Load a recordable disc.
For VHS deck
Load a cassette with safety tab intact.
3 Press VIDEO Plus+ to access the VIDEO Plus+ screen.
4 Press the number buttons to
VIDEO Plus+ PRGM
enter the PlusCode number of a
programme you wish to record,
then press ENTER.
PLUSCODE NO.
DATE
1 2 3 4
START
STOP
TV PROG
● If you have made a mistake, press
REC MODE
DAILY/WEEKLY
VPS/PDC
NAME
CANCEL and input the correct
SP
ON
number before you press ENTER.
OK
ENTER PLUSCODE NO. WITH [0-9] KEYS
● To clear all entered numbers at a
THEN PRESS [ENTER]
time, press CLEAR (8).
● If the number you entered is
invalid, “PLUSCODE NO. ERROR CONFIRM PLUSCODE NO.
THEN RETRY” appears on the TV screen. Input a valid PlusCode
number.
● If “GUIDE PROGRAMME IS NOT SET” appears on the TV screen,
set Guide Program numbers manually. (墌 pg. 83)
● When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMME” appears on the TV screen, you need to cancel some
of the reserved programmes. (墌 pg. 34)
Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
VHS
29
2 For DVD deck
You can programme each deck to timer-record as many as
8 programmes up to 30 days ahead.
With the VIDEO Plus+ system, timer programming is greatly
simplified because each TV programme has a corresponding code
number which your unit is able to recognise.
You can use the remote control to enter the PlusCode number.
●
●
●
●
EN
1 Press DVD or VHS to select the deck on which you want to
1
4
7
DVD
0–9
2
5
8
0
3
6
9
5 The PlusCode number you entered and the matching timer-
recording information are displayed on the TV screen. Check the
programme data.
● To cancel this setting, press RETURN.
CANCEL
VIDEO Plus +
TIMER
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “VIDEO Plus+ System Setup” (墌 pg. 83) and
set the Guide Program number correctly.
ENTER
6 Press w e to select the desired recording option as required.
RETURN
CLEAR (
Press rt to select the desired setting, then press ENTER.
)
IMPORTANT:
● “STOP” (To advance/go back the stop time by 30 minutes, press and
hold rt).
● “DAILY/WEEKLY” (墌 pg. 30, “Weekly/Daily Recording”)
● “VPS/PDC” (墌 pg. 30, “PDC Recording”)
● “REC MODE” (墌 pg. 27, 28, “Recording Mode”)
● “NAME” (墌 pg. 67, “Modify Title Name”) (DVD deck only)
7 Press ENTER to access the Programme Confirmation screen.
8 Press ENTER to complete timer programming.
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, the wrong channel number will
be displayed on the VIDEO Plus+ programme screen in step 5.
When this happens, set the correct Guide Program number for that
station. (墌 pg. 83, “VIDEO Plus+ System Setup”)
● To programme another timer, repeat steps 3 – 8.
● If “PROGRAMME OVERLAPPED” appears on the TV screen, see
page 35.
Satellite Receiver Users (DVD Deck Only)
To timer-record a satellite broadcast using the VIDEO Plus+
system:
A Perform “VIDEO Plus+ Timer Programming”.
B Set the satellite receiver to the appropriate channel before
the selected programme begins.
C Leave the satellite receiver’s power on.
● To disengage the timer mode, press TIMER # again.
NOTES:
● There may be cases that the VIDEO Plus+ Timer Programming
function prolongs the stop time of the programming.
● When two successive programmes are recorded on a DVD-RW disc
with the VIDEO Plus+ Timer Programming function, the beginning of
the second one may be left off the recording.
● SHOWVIEW Timer Programming is not possible on the discs used
exclusively for On-Disc Timer Programming.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
● To record the programmes received by the satellite receiver, record
on the DVD discs. For details, refer to “Satellite Receiver Users (DVD
Deck Only)” above.
29Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
9 Press TIMER # to engage the unit’s timer mode. The DVD timer
indicator lights up on the unit and the unit is automatically turned
off.
Filename [MV5SEK_08Basic TimerDub.fm]
MV5SEK_00.book Page 30 Wednesday, August 31, 2005 7:58 PM
30 EN TIMER RECORDING
Weekly/Daily Recording
You can record programmes with one of the following weekly/daily
timer settings.
WEEKLY: Select to record a weekly programme.
MON–FRI: Select to record a daily programme from Monday
through Friday.
MON–SAT: Select to record a daily programme from Monday
through Saturday.
SUN–SAT: Select to record a daily programme from Sunday
through Saturday.
PDC Recording
Now available from some TV stations, PDC (Programme Delivery
Control) is service designed to assure safe, accurate timer
recording. With this system, special code signals are transmitted
together with the audio/video signals. These code signals control
your video unit and have precedence over the advertised times you
may have preset into the timer. This means that your unit will start
and stop recording when the preset TV programmes actually start
and end — even if the broadcast time of a preset TV programme is
changed from what has been advertised. PDC is currently
available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a
few small relay transmitters. Ch.3 operates a PDC service in some
areas. All channels intend to offer this service in due course.
Check your TV programme listing guide for latest information. If the
channel you intend to record does not offer a PDC service your unit
will not start recording if PDC has been selected. Be sure to set
PDC to “OFF” if PDC is not available on your selected channel.
(See step 6 on page 29.).
NOTES:
● When you use Manual Timer Programming, set the start time (PDC
time) exactly as advertised in the TV listing. A different time than
advertised will result in no recording.
● PDC recording is also possible when a satellite receiver or a cable
system is connected to [L-2 IN/DECODER] connector on your unit.
● PDC recording is also possible via the [L-1 IN/OUT] connector.
How to check if the station being received transmits a VPS/
PDC signal
A Press DVD so that the DVD lamp lights up on the unit.
B Hold down DISPLAY for about 5 seconds. “VPS/PDC” appears
blinking on the front display panel. If a PDC signal is detected from
the station, “VPS/PDC” will stop blinking. If no PDC signal is
detected from the station, “VPS/PDC” will blink at a slower rate.
C Press DISPLAY again to return to normal display.
30Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Masterpage:Left+
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Right+
MV5SEK_00.book Page 31 Wednesday, August 31, 2005 7:58 PM
TIMER RECORDING
EN
31
1 Press DVD or VHS to select the deck on which you want to
Manual Timer Programming
perform timer programming.
2 For DVD deck
Load a recordable disc.
You can programme each deck to timer-record as many as
8 programmes up to 30 days ahead.
If you do not know the PlusCode number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
●
●
●
●
Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
For VHS deck
Load a cassette with safety tab intact.
3 Press PROG to access the
Programme Check screen.
4 For DVD deck
Press rt w e to select “DVD”
and press rt to select “NEW
TIMER PROGRAMME”, then
press ENTER.
For VHS deck
Press rt w e to select “VHS”
and press rt to select “NEW
TIMER PROGRAMME”, then
press ENTER.
5 Press rt to set the desired
VHS
DVD
VHS
EXIT
PROG
DISC TIMER PRGM
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
TIMER PROGRAMME
DATE
05/07 SAT
START
STOP
TV PROG
20:00
20:30
VTM 10
DAILY/WEEKLY
VPS/PDC
REC MODE
OFF
LP
date.
● The current date appears on the
TV screen. The date you enter
appears in its place.
DVD
START-STOP TV PROG DAILY/WEEKLY VPS/PDC REC MODE
DATE
ON
WEEKLY
05/07 SAT 19:00 - 20:00
44
SP
ON
10/07 THU 22:00 - 22:30
10
XP
OFF
11/07 FRI 13:30 - 14:00
26
LP
OFF
11/07 FRI 16:00 - 17:00
33
LP
++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++
EXIT
PROG
NAME
CONFIRM SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
6 Press w e to select “START”, then press rt to set the desired
start time.
PROG
ENTER
TIMER
● Each press of rt advances/goes back the start time in 1-min.
increments.
● To advance/go back the start time in 30-min. increments, press and
hold rt.
7 Press w e to select “STOP”, then press rt to set the desired
rtwe
stop time.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press and
hold rt.
8 Press w e to select “TV PROG”, then press rt to select the
desired channel.
9 Press w e to select the desired recording option as required.
● Refer to step 6 in “VIDEO Plus+ Timer Programming” (墌 pg. 29).
10 Press ENTER to access the Programme Confirmation screen.
11 Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 11.
● If “PROGRAMME OVERLAPPED” appears on the TV screen, see
page 35.
12 Press TIMER # to engage the unit’s timer mode. The DVD
timer indicator lights up on the unit and the unit is automatically
turned off.
● To disengage the timer mode, press TIMER # again.
Satellite Receiver Users (DVD Deck Only)
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform “Manual Timer Programming”.
B Set the satellite receiver to the appropriate channel before
the selected programme begins.
C Select “L-2” in step 8.
D Leave the satellite receiver’s power on.
NOTES:
● When two successive programmes are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
● In case of a power failure after programming, the unit’s memory
backup keeps your selections for approximately 10 minutes.
● Programmes that start after midnight must have the next day’s date.
● To record the programmes received by the satellite receiver, record
on the DVD discs. For details, refer to “Satellite Receiver Users (DVD
Deck Only)” above.
31Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Left+
MV5SEK_00.book Page 32 Wednesday, August 31, 2005 7:58 PM
32
EN
TIMER RECORDING
On-Disc Timer Programming (DVD Deck
Only)
● Each press of rt advances/goes back the start time in 1-min.
increments.
● To advance/go back the start time in 30-min. increments, press and
hold rt.
7 Press w e to select “STOP”, then press rt to set the desired
stop time.
On-Disc Timer Programming is a function used with discs that are
especially intended for a specific programme. The disc is then
programmed for a programme you always watch every day or
every week. Since older programmes are automatically
overwritten, a single DVD-RAM/RW (VR mode) disc can be used
without worrying about how much recording capacity remains.
(墌 pg. 33)
You can programme each disc to timer-record as many as
8 programmes.
●
●
●
●
Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press and
hold rt.
8 Press w e to select “TV PROG”, then press rt to select the
desired channel.
9 Set “DAILY/WEEKLY” option.
● Refer to step 6 in “VIDEO Plus+ Timer Programming” (墌 pg. 29).
● It is necessary to set “DAILY/WEEKLY” option for On-Disc Timer
Programming. (墌 pg. 30, “Weekly/Daily Recording”)
10 Set the other recording options as required.
● You can select XP, SP, LP, EP or FR480 mode for “REC MODE”.
However, you cannot select FR (JUST), FR60–FR360 and FR420.
● Refer to step 6 in “VIDEO Plus+ Timer Programming” (墌 pg. 29).
● It is not possible to use the Free Rate function. (墌 pg. 62)
11 Press ENTER to access the Programme Confirmation screen.
12 Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 12.
ATTENTION:
● On-Disc Timer Programming is possible only with the disc for OnDisc Timer Programming.
● If data is recorded on a disc for On-Disc Timer Programming using
a unit from another manufacturer, On-Disc Timer Programming
may no longer function properly.
DVD
Satellite Receiver Users
To timer-record a satellite broadcast using the On-Disc Timer
Programming function:
A Perform “On-Disc Timer Programming (DVD Deck Only)”.
B Set the satellite receiver to the appropriate channel before
the selected programme begins.
C Select “L-2” in step 8.
D Leave the satellite receiver’s power on.
To Timer-record The Programme With The Programmed Disc
1 Load a programmed disc.
2 Press TIMER #. The unit turns off and “
” appears on
the front display panel. The DVD timer indicator also lights up on
the unit and the unit is automatically turned off.
● To disengage the timer mode, press TIMER # again.
PROG
ENTER
TIMER
rtwe
To Make The Disc For On-Disc Timer Programming
1 Load a recordable disc.
2 Press DVD so that the DVD lamp lights up on the unit.
3 Press PROG to access the Programme Check screen.
4 When On-Disc Timer Programming is made for the first
time on the disc
Press rt to select “DISC TIMER PRGM”, then press ENTER.
● When some programmes are recorded on the disc, a caution
message appears. In such a case, backup the programmes as
required, then format the disc before making On-Disc Timer
Programming. (墌 pg. 89)
When On-Disc Timer Programming has already been made on
the disc
Press rt to select “DISC TIMER PROGRAMME”, then press
ENTER.
5 Press rt to set the desired date.
● The current date appears on the TV screen. The date you enter
appears in its place.
6 Press w e to select “START”, then press rt to set the desired
start time.
32Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
NOTES:
● On-Disc Timer Programming is not possible on a DVD-RW disc
formatted in video mode. (墌 pg. 89)
● The information of a programme recorded with On-Disc Timer
Programming is not stored in the library. (墌 pg. 71)
● The play list is not created for the programmes recorded with On-Disc
Timer Programming. (墌 pg. 68)
● Basic Recording (墌 pg. 26), VIDEO Plus+ Timer Programming
(墌 pg. 29), Manual Timer Programming (墌 pg. 31) are not possible
on the On-Disc Timer programmed disc.
● The beginning of a programme may not be recorded. Also, if the 1st
programme’s recording stop time and the 2nd programme’s recording
start time is the same, the ending of the 1st programme may not be
recorded.
● If there is a power cut while recording, the recordings before the
power cut are not guaranteed.
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Right+
MV5SEK_00.book Page 33 Wednesday, August 31, 2005 7:58 PM
TIMER RECORDING
EN
How Discs Are Overwritten
(Example 1)
To record a 1-hour serial drama every Friday in SP mode
Overwritten
1st
Blank
2nd
1st
2nd
Overwritten
3rd
The first programme is
overwritten by the third.
(Example 2)
To record a 15-minute serial drama every morning in XP mode
4th
1st
8th
5th
3rd
2nd
7th
6th
(Example 3)
To record a 90-minute serial drama every Sunday in SP mode
2nd
3rd
Blank
Blank
1st
Blank
Areas treated as blank cannot be played back even if they contain
recorded material.
NOTES:
● On-Disc Timer Programming may not always work as these examples.
● On-Disc Timer Programming may not complete successfully if the recording stop time is extended due to PDC.
33Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
4th
3rd
The second programme is
overwritten by the forth.
33
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Left+
MV5SEK_00.book Page 34 Wednesday, August 31, 2005 7:58 PM
34
EN
TIMER RECORDING
Check, Cancel And Change Programmes
1 When the DVD timer indicator lights on the front display
VHS
panel
Press TIMER #, then press 1.
DVD
When “
” lights on the front display panel and the DVD
timer indicator also lights up on the front display panel.
Press 1.
When “SAT #” lights on the front display panel
Press SAT #, then press 1.
2 Press PROG to access the Programme Check screen, then
CANCEL
PROG
ENTER
press rt w e to select “VHS” or “DVD”.
TIMER
SAT
● To return to the previous screen after you check the programme,
press PROG again.
rtwe
To cancel the programme
Press rt to select a programme to be cancelled, then press
CANCEL.
3 Press rt to select the programme, then press ENTER. The
programme screen appears.
4 Change the settings of the desired recording options as
required.
● Refer to steps 5 – 10 in “Manual Timer Programming” (墌 pg. 31).
5 Press PROG to complete timer correction. The normal screen
resumes.
6 For VIDEO Plus+, Manual or On-Disc Timer Programming
(DVD deck only)
Press TIMER #.
For Automatic Satellite Programme Recording
Press SAT # for 2 seconds or more.
● The DVD timer indicator also lights up on the front display panel and
the VHS deck is automatically selected. When the VHS deck is in
timer standby mode, the unit is automatically turned off.
NOTE:
When you check, cancel and change a On-Disc Timer Programming,
be sure to insert the On-Disc Timer programmed disc.
Programme’s information on the front display panel
You can check the details of the programmes on the front display
panel. However, it is not possible to cancel or change the
programme’s setting.
A Press PROG.
● “NEW PROG” or “P-1” (if 8 programmes have already been set)
appears.
B Press rt until the desired programme number (“P-1” to “P8”) appears, then press ENTER.
C Press e.
● Each time you press e, the indication changes as follows (the
settings in parentheses are examples):
Date (“DATE 08.03SU”) ] Start time (“ON 11:00”) ] Stop time
(“OFF 11:30”) ] Channel (“PR 1”) ] Weekly/Daily (“MO-FR
DAILY”) ] Programme number (“P-1”) and recording mode (“SP”)
] (Back to the beginning)
D Press PROG to complete checking.
● The normal display resumes.
34Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Right+
MV5SEK_00.book Page 35 Wednesday, August 31, 2005 7:58 PM
TIMER RECORDING
EN
35
When Programmes Overlap Each Other
If “PROGRAMME OVERLAPPED” appears, you have another
programme overlapping the programme you have just made.
Confirm with the arrow on “OK”, then press PROG. The
Programme Check screen appears and conflicting programmes
will be highlighted in pink.
Example: Programme 3 (you
have just made) and
programme 4 overlap each
other.
CANCEL
PROG
ENTER
1 Confirm the overlapping
programmes. Overlapping
programmes appear on the TV
screen.
NOTE:
VHS
DVD
DATE
START-STOP TV PROG DAILY/WEEKLY VPS/PDC REC MODE
05/07 SAT 18:10-20:00
ON
L-1
SP
06/01 THU 18:10-20:00
L-1
ON
SP
10/07 THU 19:00-20:00
7
XP
WEEKLY
OFF
10/07 THU 19:45-20:30
7
OFF
LP
++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++
EXIT
PROG
DISC TIMER PRGM
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
If you do not mind this overlap, press PROG to finish the timer
programme setting. The programme whose start time is earlier will be
recorded and the other one will not be recorded correctly.
2 Press rt to select the desired programme to be cancelled or
changed.
● If programme on the DVD deck and programme on VHS deck overlap
each other, mark appears on the left of the date of each item.
Press rt w e to select “VHS” or “DVD”, then select the programme
to be cancelled or changed.
To cancel the programme
Press CANCEL.
● “THE TIMER PROGRAMMING SETTING WAS CANCELLED”
appears on the TV screen for about 5 seconds, then the normal
screen resumes.
To change the programme setting
Press ENTER, then go to step 3.
3 Change the programme setting.
● Refer to steps 5 – 10 in “Manual Timer Programming” (墌 pg. 31).
4 Press PROG to check if the conflict has been settled. The
Programme Check screen appears.
5 Engage the unit’s timer mode.
● Refer to step 6 in “Check, Cancel And Change Programmes”
(墌 pg. 34).
NOTE:
When any overlaps remain after deletion and modification of
programmes, the Programme Check screen remains showing the
conflicting programmes. In such a case, repeat the procedure above
until the conflict is solved.
35Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Left+
MV5SEK_00.book Page 36 Wednesday, August 31, 2005 7:58 PM
36
EN
TIMER RECORDING
Automatic Satellite Programme
Recording (DVD Deck Only)
This function allows you to automatically record a satellite
programme which is timer-programmed on your external satellite
receiver. Connect a satellite receiver to the unit’s [L-2 IN/
DECODER] connector and programme the timer on the satellite
receiver. The unit starts or stops recording by the signals input
from the satellite receiver. After recording, the unit’s power shuts
off automatically.
● When you record programmes by connecting to a digital terrestrial
receiver (Freeview receiver or similar), perform the same steps as
“Automatic Satellite Programme Recording (DVD Deck Only)”
(墌 pg. 36).
● Be sure not to turn on the satellite receiver before the programme
is executed; otherwise, the unit will start recording when the
satellite receiver’s power is turned on.
● If you have connected another appliance other than a satellite
receiver to the [L-2 IN/DECODER] connector, be sure not to
engage the Automatic Satellite Programme Recording mode;
otherwise, the unit will start recording when the connected
appliance’s power is turned on.
● Automatic Satellite Programme Recording and timer-recording
cannot be done at the same time.
DVD
SAT
36Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
1 Load a recordable disc.
2 Press DVD so that the DVD lamp lights up on the unit.
3 Press REC MODE repeatedly to set the recording mode.
4 Press and hold SAT # for about 2 seconds to engage the
Automatic Satellite Programme Recording mode. “SAT #” appears
on the front display panel.
NOTES:
ATTENTION:
REC MODE
● Make sure the satellite receiver is connected to the unit’s [L-2 IN/
DECODER] connector.
● Programme the timer on the satellite receiver.
● Slide the TV/DVD switch to DVD.
● To disengage the Automatic Satellite Programme Recording mode,
press SAT #.
● If the unit’s power is off, it is not possible to engage the Automatic
Satellite Programme Recording mode.
● For timer programming of the satellite receiver, refer to the instruction
manual of the satellite receiver.
● Automatic Satellite Programme Recording is not possible if your
satellite receiver does not have a timer.
● Pressing the unit’s 1 button while Automatic Satellite Programme
Recording is in progress turns off the unit’s power and disengages
the Automatic Satellite Programme Recording mode.
● If there are more than one satellite programmes you wish to record
with Automatic Satellite Programme Recording, it is not possible to
set different recording modes for each programme.
● Depending on the type of satellite receiver, the unit may not record a
slight portion of the beginning of the programme or may record
slightly longer than the actual length of the programme.
● Just Clock (墌 pg. 88) does not work when the Automatic Satellite
Programme Recording mode is engaged.
● You can also record a programme from your cable system in the
same way if the system has a timer.
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Right0
MV5SEK_00.book Page 37 Wednesday, August 31, 2005 7:58 PM
EDITING
One-Touch Expert Dubbing (From VHS
To DVD)
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Make sure that both the DVD deck and the VHS deck are in the
stop mode.
VHS
EN
37
Auto Recording Mode Optimizer
The unit calculates the total recording time of the VHS tape and
automatically selects the optimum DVD recording mode.
Auto Title Creation Dubbing
Each index code (VISS signal) on the VHS tape is detected and
created as a title on the DVD disc. When a tape contains multiple
VISS signals, separate titles are created for each VISS signal
(for each programme).
Auto Blank-Cut Dubbing
Recording to the DVD pauses during blank sections on the VHS
tape and restarts when a signal is detected.
1 For DVD deck
Load a recordable disc.
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
● Load an empty disc. If a disc with recorded data is loaded, the time
calculation will not include the recorded section, and so dubbing may
not be possible for an entire tape.
For VHS deck
Load a cassette you want to dub.
2 Press and hold VHS] for more than 2 seconds to start
dubbing.
● The unit fast-forwards and rewinds the tape to calculate the recording
time, then starts dubbing after setting automatically the recording
mode that enables recording to fill exactly one disc. It takes a few
minutes to calculate the recording time.
● After dubbing is completed, the VHS deck rewinds the tape
automatically and the unit shuts off.
● To cancel dubbing, press VHS] again so that “]” lights off.
● To stop dubbing, press 8.
Stop and pause mode on the DVD deck
When recording, the unit automatically searches for the blank
section of the disc no matter where the disc was stopped or
paused.
In contrast to VHS tapes, recorded sections on discs cannot be
overwritten.
NOTES:
● When you turn on the unit next time, press VHS] so that “]” lights
off before performing any operations. If it is not done, recording on
the DVD deck is not possible.
● It is not possible to dub a tape with a copy protection signal.
● If there is no remaining recording time left on a DVD disc, the tape
automatically stops at that position.
● It is not possible to perform other operations like Live Memory
Playback. Check the recorded programme on the disc after dubbing.
● It is not possible to perform dubbing on the On-Disc Timer
programmed disc. Either cancel the disc programming, or use an
unprogrammed disc.
● If the index code (VISS signal) is found on a tape during One-Touch
Expert Dubbing, a single title is created. While creating a title, the
dubbing stops. Dubbing starts again once the title is created. When a
tape contains multiple VISS signals, separate titles are created for
each VISS signal.
● During still picture on the VHS deck, the images may jitter, but this is
not a malfunction.
37Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Left+
MV5SEK_00.book Page 38 Wednesday, August 31, 2005 7:58 PM
38
EN
EDITING
Manual Dubbing (From VHS To DVD)
Load a recordable disc.
For VHS deck
Load a cassette you want to dub.
Dubbing A Part Of A Cassette
2 Press VHS] to select the dubbing direction.
You can dub the selected scenes on a tape to the DVD disc,
starting and stopping wherever you wish.
●
●
●
●
1 For DVD deck
● “]” lights up on the unit.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Make sure that both the DVD deck and the VHS deck are in the
stop mode.
3 Set “VHS]DVD DUBBING” to “1 PROG”. (墌 pg. 81)
4 Prepare the VHS deck for dubbing.
A Press VHS/DVD on the unit repeatedly or VHS on the remote
control so that the VHS lamp lights up on the unit.
B Locate the point from where you want to start dubbing, then
pause playback.
● During still picture on the VHS deck, the images may jitter, but this is
not a malfunction.
5 Prepare the DVD deck for dubbing.
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
VHS/DVD VHS
DUBBING
A Press VHS/DVD on the unit repeatedly or DVD on the remote
control so that the DVD lamp lights up on the unit.
B Press REC MODE repeatedly to set the recording mode.
C Press and hold 7, then press 9 so that the DVD deck enters
the Record Pause mode.
6 Press and hold DUBBING for more than 2 seconds to start
dubbing.
7 Press 8 to stop recording on the DVD deck.
● Both the VHS deck and the DVD deck are stopped.
● After dubbing is completed, press VHS] so that “]” lights off. If it is
not done, recording on the DVD deck is not possible.
VHS
REC MODE
38Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
NOTES:
DVD
● It is not possible to dub a tape with a copy protection signal.
● If there is no remaining recording time left on a DVD disc, the tape
automatically stops at that position.
● It is not possible to perform other operations like Live Memory
Playback. Check the recorded programme on the disc after dubbing.
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Right+
MV5SEK_00.book Page 39 Wednesday, August 31, 2005 7:58 PM
EDITING
Disc Dubbing (From DVD To VHS)
For VHS deck
Load a cassette with the record safety tab intact.
You can easily use this unit for dubbing without connecting any
other equipment.
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Make sure that both the DVD deck and the VHS deck are in the
stop mode.
● Set “SUPERIMPOSE” to “OFF”. (墌 pg. 79)
}DVD
VHS
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
39
Load a disc you want to dub.
Dubbing An Entire Disc
STANDBY/ON
EN
1 For DVD deck
AUDIO
VHS
DUBBING
DVD
DV IN
VHS/DVD DUBBING
VHS
DVD
REC MODE
PROGRESSIVE
SCAN
39Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
2 Press VHS/DVD on the unit repeatedly or VHS on the remote
control so that the VHS lamp lights up on the unit.
3 Press REC MODE repeatedly to set the recording mode.
4 Press }DVD to select the dubbing direction.
● “}” lights up on the unit.
5 Press and hold DUBBING for more than 2 seconds to start the
dubbing.
● If the tape has not been rewound, the VHS deck rewinds the tape
automatically. When the VHS deck has finished rewinding, dubbing
begins automatically.
● After dubbing is completed, the VHS deck rewinds the tape
automatically and the unit shuts off.
● To stop dubbing, press 8.
NOTES:
● When you turn on the unit next time, press }DVD so that “}” lights
off before performing any operations. If it is not done, recording on
the VHS deck is not possible.
● It is not possible to start dubbing if the unit retains a memory of the
resume points. Press 8 twice to clear the resume points.
● There may be a discrepancy of several seconds between where you
intend dubbing to start, and where it actually starts.
● The superimposed indication during the operation or dubbing is not
recorded.
● When the end of the tape is reached during dubbing, dubbing is done
and “[” indicator on the front panel blinks. When pressing x
(EJECT) to eject the tape, “[” indicator on the front panel stops
blinking.
● When the progressive mode is set, “}” does not light up on the unit.
Press PROGRESSIVE SCAN so that video output indicator ( )
lights off on the front display panel.
● It may be impossible to dub a DVD-R or DVD-RW (Video mode) disc
recorded on the devices from other manufacturers or on a PC. In
such case, perform “Manual Dubbing (From DVD To VHS)”
(墌 pg. 40).
● It is not possible to perform other operations like Live Memory
Playback. Check the recorded programme on the disc after dubbing.
● If “]” lights up on the unit and you play back a DVD VIDEO disc, the
images dubbed to the VHS deck may not be output to the TV
properly.
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Left+
MV5SEK_00.book Page 40 Wednesday, August 31, 2005 7:58 PM
40
EN
EDITING
1 For DVD deck
Manual Dubbing (From DVD To VHS)
Load a disc you want to dub.
For VHS deck
Load a cassette with the record safety tab intact.
Dubbing A Part Of A Disc
You can dub the selected scenes on a DVD disc to a tape, starting
and stopping wherever you wish.
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Make sure that both the DVD deck and the VHS deck are in the
stop mode.
● Set “SUPERIMPOSE” to “OFF”. (墌 pg. 79)
VHS
STANDBY/ON
REC
DVD
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
VHS/DVD
DUBBING
● “}” lights up on the unit.
3 Prepare the DVD deck for dubbing.
A Press VHS/DVD on the unit repeatedly or DVD on the remote
control so that the DVD lamp lights up on the unit.
B Locate the point from where you want to start dubbing, then
pause playback.
4 Prepare the VHS deck for dubbing.
A Press VHS/DVD on the unit repeatedly or VHS on the remote
control so that the VHS lamp lights up on the unit.
B Press REC MODE repeatedly to set the recording mode.
C Press and hold 9, then press 7 so that the VHS deck enters
the Record Pause mode.
5 Press and hold DUBBING for more than 2 seconds to start the
dubbing.
PR
VHS/DVD
S-VIDEO
2 Press }DVD to select the dubbing direction.
DVD
6 Press 8 to stop recording on the VHS deck.
● Both the VHS deck and the DVD deck are stopped.
● After dubbing is completed, press }DVD so that “}” lights off. If it is
not done, recording on the VHS deck is not possible.
NOTES:
VHS
DVD
PR +/–
ENTER
REC MODE
PROGRESSIVE
SCAN
40Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
● It is not possible to start dubbing if the unit retains a memory of the
resume points. Press 8 twice to clear the resume points.
● There may be a discrepancy of several seconds between where you
intend dubbing to start, and where it actually starts.
● The superimposed indication during the operation or dubbing is not
recorded.
● When the end of the tape is reached during dubbing, dubbing is done
and “[” indicator on the front panel blinks. When pressing x
(EJECT) to eject the tape, “[” indicator on the front panel stops
blinking.
● When the progressive mode is set, “}” does not light up on the unit.
Press PROGRESSIVE SCAN so that video output indicator ( )
lights off on the front display panel.
● It is not possible to perform other operations like Live Memory
Playback. Check the recorded programme on the disc after dubbing.
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Right+
MV5SEK_00.book Page 41 Wednesday, August 31, 2005 7:58 PM
EDITING
DV Dubbing (DVD Deck Only)
NOTES:
● Be sure to use the DV cable VC-VDV 204U for connection.
● When you connect a PC to the [DV IN] connector, we do not
assure the normal operation of this unit.
Your unit
VHS
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
41
on the unit’s front panel.
You can dub programmes from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
STANDBY/ON
EN
1 Connect a camcorder or DV equipment to the [DV IN] connector
DVD
DV IN
To [DV IN]
2 Load a DVD-RAM/RW/R disc on the unit.
3 Press PR +/– to set the channel to “DV”.
● The “DV DUBBING” controller appears on the TV screen.
● If “
” does not appear on the “DV DUBBING” controller, make
sure the DV equipment is connected correctly.
4 Press w e to select
5 Press rt to select the desired
, then press ENTER.
sound track, then press ENTER.
AUDIO 1: Select this to record the
original stereo sound played
back on the connected DV
equipment.
AUDIO 2: Select this to record the
dubbed stereo sound played
back on the connected DV
equipment.
MIX: Select this to record the sound of both “AUDIO 1” and
“AUDIO 2”.
● Note that this selection is not available when the source programme
is recorded in 16BIT (48 kHz) mode.
6 Press REC MODE repeatedly to set the recording mode.
7 Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: 4, 5, 3, 8, 9.
Camcorder
DV cable
(VC-VDV 204U)
(not provided)
● To play back in slow speed (1/10 of the normal speed), press 9 to
pause playback, then press 3 or 5.
● To play back frame-by-frame, press 9 to pause playback, then press
9 repeatedly. Each press of 9 advances a frame.
● To change the playback direction, press 3 or 5.
8 Press w e to select
DV connector
DV equipment
, then press ENTER. The
dubbing starts.
● Playback on the external DV equipment and recording on the unit
should start simultaneously.
● When the playback from the beginning is not possible, the “DV
DUBBING” controller cannot be used. Perform dubbing without using
the “DV DUBBING” controller. (墌 below)
● To pause dubbing, press w e to select
, then press
ENTER. Both the unit and the external DV equipment pause dubbing.
Pressing 9 on the unit also works the same way.
● To clear the “DV DUBBING” controller from the TV screen, press
ON SCREEN.
9 Press 8 on the remote control to stop dubbing.
● Both the unit and the external DV equipment stop dubbing.
NOTES:
● Dubbing copyright guarded programmes is not possible.
● Original DV informations such as the recording date and time are not
recorded.
● The superimposed indication during the operation or dubbing is not
recorded.
● It is not possible to perform dubbing when “]” lights up on the unit.
Press VHS] so that “]” lights off.
Performing dubbing without using the “DV DUBBING”
controller
A Press PR +/– to set the channel to “DV”.
B Press REC MODE repeatedly to set the recording mode.
C Start playback on the external DV equipment slightly before the
actual point from where you wish to start dubbing.
D Press 7 on the unit to start recording. Or press and hold 7 and
press 4 on the remote control. The dubbing starts.
E When the dubbing ends, press 8 on the unit, then stop
playback on the external DV equipment.
41Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Left+
MV5SEK_00.book Page 42 Wednesday, August 31, 2005 7:58 PM
42
EN
EDITING
Edit From A Camcorder
● Slide the TV/DVD switch to DVD.
You can use a camcorder as the source player and your unit as the
recording deck.
A If the camcorder has no S-VIDEO output connector:
A If the camcorder has no S-VIDEO output connector:
— connect the camcorder’s AUDIO/VIDEO OUT connectors to the
unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors on the front
panel.
● When using a monaural camcorder, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.
Your unit
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
1 Make connections.
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
Recorder
To [VIDEO/AUDIO
((MONO) L/R)] input
B If the camcorder has an S-VIDEO output connector:
— connect the camcorder’s AUDIO OUT and S-VIDEO OUT
connectors to the unit’s [AUDIO] and [S-VIDEO] input connectors
on the front panel.
2 Press VHS/DVD on the unit repeatedly to select the recording
deck.
3 Press PR +/– to select “F-1”.
● Set “F-1 INPUT” to “VIDEO” for the [VIDEO] input connector, or
“S-VIDEO” for the [S-VIDEO] input connector, depending on the
connector being used. (墌 pg. 45)
Audio/video cable (not provided)
4 Press REC MODE repeatedly to set the recording mode.
5 Start playback on the camcorder slightly before the actual point
from where you wish to start dubbing.
6 Press 7 on the unit to start recording. Or while holding 7, press
4 on the remote control. The dubbing starts.
7 Press 8 on the unit, then stop playback on the camcorder.
NOTES:
● All necessary cables can be obtained from your dealer.
● Refer to the camcorder’s instruction manual for operating procedure.
● The quality of dubbed picture becomes poorer than that of the
original.
AUDIO/VIDEO OUT
Player
B If the camcorder has an S-VIDEO output connector (DVD
deck only):
Your unit
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
To [S-VIDEO]
input
To [AUDIO] input
S-video cable
(not provided)
Recorder
Audio cable
(not provided)
S-VIDEO OUT
AUDIO OUT
Player
42Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Right+
MV5SEK_00.book Page 43 Wednesday, August 31, 2005 7:58 PM
EDITING
Edit To Or From Another Recorder
You can use your unit as the source player or as the recording
deck.
NOTE:
When using another recorder as the recording deck, refer to its
instruction manual.
A When using your unit as the source player:
TV receiver
Player
Your unit
EN
43
Slide the TV/DVD switch to DVD.
1 Connect the player’s 21-pin SCART connector to the unit’s 21pin SCART connector as illustrated.
A When using your unit as the source player:
— connect its [L-1 IN/OUT] connector to the recording deck.
B When using your unit as the recording deck:
— connect its [L-1 IN/OUT] or [L-2 IN/DECODER] connector to
the source player.
● If another recorder is compatible with the Y/C signal (DVD deck only):
— when using your unit as the source player, set “L-1 OUTPUT” to
“SCART S-VIDEO”. (墌 pg. 44)
— when using your unit as the recording deck, set “L-2 SELECT” to
“S-VIDEO/RGB”. (墌 pg. 45)
2 Press VHS/DVD repeatedly to select the recording deck.
3 Press PR +/– to select “L-1” for the [L-1 IN/OUT] connector, or
21-pin SCART cable (provided)
21-pin SCART cable
(not provided)
“L-2” for the [L-2 IN/DECODER] connector, depending on the
connector being used when using this unit as the recording deck.
For DVD deck
● When using the [L-1 IN/OUT] connector, set “L-1 OUTPUT” to
“VIDEO” or “S-VIDEO”. (墌 pg. 44)
● When using the [L-2 IN/DECODER] connector, set “L-2 SELECT” to
“VIDEO/RGB” or “S-VIDEO/RGB”. (墌 pg. 45)
4 Press REC MODE repeatedly to set the recording mode.
5 Engage the Play mode of the source player.
6 Engage the Record mode of the recording deck.
7 Stop recording on the recording deck, then stop playback on the
Another recorder
Recorder
source player.
B When using your unit as the recording deck:
TV receiver
Recorder
Your unit
21-pin SCART
cable (provided)
21-pin SCART cable
(not provided)
Another recorder
Player
43Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
NOTES:
● All necessary cables can be obtained from your dealer.
● For Y/C signal input/output, be sure to use a 21-pin SCART cable
that is compatible with the Y/C signal.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting. (墌 pg. 79)
● If you are using another recorder with S-Video and Audio output
connectors, connect its S-Video and Audio output connectors to this
unit’s [S-VIDEO] and [AUDIO] input connectors on the front panel.
Then, set the unit’s input mode to “F-1” in step 3, and set “F-1 INPUT”
to “S-VIDEO”. (墌 pg. 45) (DVD deck only)
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Left+
MV5SEK_00.book Page 44 Wednesday, August 31, 2005 7:58 PM
44
EN
EDITING
* The boldface settings below indicate the settings at your purchase.
Output/Input Set
8 L-1 OUTPUT — SCART VIDEO / SCART S-VIDEO / SCART
RGB / COMPONENT
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
SCART VIDEO: If a connected appliance’s input is compatible only
with regular video signals, set to “SCART VIDEO”.
SCART S-VIDEO: If a connected appliance’s input is compatible
VHS
with Y/C signals, set to “SCART S-VIDEO”. You can obtain highquality picture. (For connection, be sure to use a 21-pin SCART
cable that is compatible with the Y/C signal.)
SCART RGB: If a connected appliance’s input is compatible with
RGB signals, set to “SCART RGB”. You can obtain a high-quality
RGB picture.
COMPONENT: If a connected appliance’s input is compatible with
Y/PB/PR signals, set to “COMPONENT”. You can obtain a highquality Y/PB/PR picture. Switch the TV to the input that you can
watch component video pictures.
DVD
8 L-1 INPUT — VIDEO / S-VIDEO
VIDEO: If a connected appliance’s output is compatible only with
regular video signals, set to “VIDEO”.
S-VIDEO: If a connected appliance’s output is compatible with Y/C
ENTER
signals, set to “S-VIDEO”. You can obtain a high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
NOTES:
● If “L-1 OUTPUT” is set to “SCART S-VIDEO”, “SCART RGB” or
“COMPONENT”, it is not possible to set “L-1 INPUT” to “S-VIDEO”.
● If “L-2 SELECT” is set to “DECODER”, it is not possible to set “L-1
INPUT” to “S-VIDEO”.
● If “L-2 SELECT” is set to “DECODER”, it is only possible to set “L-1
OUTPUT” to “SCART VIDEO”.
● Component video signals are not output from the [L-1 IN/OUT]
connector.
● When Progressive scan mode is engaged, it is not possible to select
the setting of “L-1 OUTPUT”. (墌 pg. 44)
SET UP
L-1 Output And L-1 Input Setting
The [L-1 IN/OUT] connector accepts and delivers either a composite
signal (regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set “L-1
OUTPUT” and “L-1 INPUT” to the appropriate mode depending on
the type of appliance connected to the unit’s [L-1 IN/OUT] connector.
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “FUNCTION SET UP”, then press t.
3 Press w e to select “VIDEO
DVD SET UP
IN/OUT”, then press t.
4 Press rt to select “L-1
OUTPUT” or “L-1 INPUT”, then
press ENTER.
5 Press rt to select the
appropriate setting, then press
ENTER.
FUNCTION SET UP
VIDEO IN/OUT RECORDING SET
MONITOR TYPE
VIDEO
L-1 INPUT
L-1 OUTPUT
L-2 SELECT
EXIT
OTHERS
4:3LB
VIDEO
F-1 INPUT
SET UP
INITIAL SET UP
DISPLAY SET
OK
SELECT
SCART VIDEO
VIDEO/RGB
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
6 Press SET UP to complete the setting.
NOTES:
● If “L-1 INPUT” or “L-1 OUTPUT” is set to “S-VIDEO”, the monocrome
signal is output from VHS deck. Be sure to select setting other than
“S-VIDEO” when you use the VHS deck.
● When the progressive mode is set, be sure to set “L-1 OUTPUT” to
“COMPONENT”. (墌 pg. 44)
● If “L-1 OUTPUT” is not set to “COMPONENT”, it is not possible to
output images from the [COMPONENT VIDEO OUT] connector.
44Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_08Basic TimerDub.fm]
Masterpage:Right+
MV5SEK_00.book Page 45 Wednesday, August 31, 2005 7:58 PM
EDITING
EN
45
L-2 Select Setting
F-1 Input Setting
Set “L-2 SELECT” to the appropriate mode depending on the type
of appliance connected to the unit’s [L-2 IN/DECODER] connector.
Set “F-1 INPUT” to the appropriate mode depending on the
connector ([VIDEO] or [S-VIDEO]) being used on the front panel.
1 Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting”
1 Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting”
(墌 pg. 44).
(墌 pg. 44).
2 Press rt to select “L-2 SELECT”, then press ENTER.
3 Press rt to select the
2 Press rt to select “F-1 INPUT”, then press ENTER.
3 Press rt to select the
DVD SET UP
appropriate setting, then press
ENTER.
4 Press SET UP to complete the
setting.
NOTES:
FUNCTION SET UP
VIDEO IN/OUT RECORDING SET
MONITOR TYPE
INITIAL SET UP
DISPLAY SET
OTHERS
4:3LB
VIDEO
F-1 INPUT
VIDEO
L-1 INPUT
L-1 OUTPUT
L-2 SELECT
SCART VIDEO
VIDEO/RGB
S-VIDEO/RGB
S-VIDEO/RGB
SAT VIDEO/RGB
SELECT WITH [CURSORS]
DECODER
THEN PRESS [ENTER]
DVD SET UP
appropriate setting, then press
ENTER.
4 Press SET UP to complete the
setting.
FUNCTION SET UP
VIDEO IN/OUT RECORDING SET
MONITOR TYPE
INITIAL SET UP
DISPLAY SET
OTHERS
4:3LB
VIDEO
VIDEO
VIDEO
S-VIDEO
F-1 INPUT
L-1 INPUT
L-1 OUTPUT
L-2 SELECT
SCART VIDEO
VIDEO/RGB
● If “L-2 SELECT” is set to
SELECT
EXIT
“S-VIDEO/RGB”, it is not possible
to output colour signals correctly
from the VHS deck.
● If “L-2 SELECT” is set to “DECODER”, only the DVD deck operates
properly.
* The boldface settings below
indicate the settings at your
purchase.
* The boldface settings below indicate the settings at your purchase.
S-VIDEO: When connecting an appliance to the [S-VIDEO] input
8 L-2 SELECT — VIDEO/RGB / S-VIDEO/RGB /
SAT VIDEO/RGB / DECODER
NOTE:
SET UP
OK
SET UP
EXIT
OK
SELECT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
8 F-1 INPUT — VIDEO / S-VIDEO
VIDEO: When connecting an appliance to the [VIDEO] input
connector, set to “VIDEO”.
connector, set to “S-VIDEO”.
Select “VIDEO/RGB” or “S-VIDEO/RGB” to use this unit as the
recording deck with the player connected to the [L-2 IN/
DECODER] connector, or to use the satellite receiver connected to
the [L-2 IN/DECODER] connector.
VIDEO/RGB: If a connected appliance’s output is compatible with
regular video signals, set to “VIDEO/RGB”.
S-VIDEO/RGB: If a connected appliance’s output is compatible with
Y/C signals, set to “S-VIDEO/RGB”. You can obtain high-quality
picture. (For connection, be sure to use a 21-pin SCART cable
that is compatible with the Y/C signal.)
Select “SAT VIDEO/RGB” to view a satellite programme with the
TV set while the unit is turned off. (墌 pg. 76)
SAT VIDEO/RGB: If a connected satellite receiver’s output is
compatible with regular video signals, set to “SAT VIDEO/RGB”.
DECODER*: To use a decoder connected to the [L-2 IN/DECODER]
connector.
* This setting is not available in the U.K.
NOTES:
● If you have a satellite receiver or a decoder connected to the [L-2 IN/
DECODER] connector, be sure to set “L-2 SELECT” back to
appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to the [L-2
IN/DECODER] connector, leave “L-2 SELECT” set to “VIDEO/RGB”.
● When “L-2 SELECT” is set to “SAT VIDEO/RGB”, “SAT” appears on
the TV screen or front display panel instead of “L-2”.
● If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible to set
“L-2 SELECT” to “DECODER” or “SAT VIDEO/RGB”.
● If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to set “L-2
SELECT” to “DECODER”.
● If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” to “SAT
VIDEO/RGB” or “DECODER”, be sure to connect the [L-1 IN/OUT]
connector with a TV.
● If “L-2 SELECT” is set to “S-VIDEO/RGB”, the monocrome signal is
output from VHS deck. Be sure to select setting other than
“S-VIDEO/RGB” when you use the VHS deck.
45Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
● If “F-1 INPUT” is set to “S-VIDEO”, the monocrome signal is output
from VHS deck. Be sure to select “VIDEO” when you use the VHS
deck.
Filename [MV5SEK_08Basic TimerDub.fm]
MV5SEK_00.book Page 46 Wednesday, August 31, 2005 7:58 PM
46
EN
Masterpage:Left+
EDITING
1 Connect the unit and a digital audio device using an optional
coaxial cable.
Digital Audio Dubbing
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
However, it is not possible to dub copy-protected discs.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
2 Place a disc on the unit and load an MD or CD on the connected
digital audio device.
3 Select the audio to be dubbed.
4 Start playback slightly before the actual point from where you
wish to start dubbing.
5 Press 9 to pause playback.
6 Select the input mode on the connected digital audio device.
7 Press 4 to start playback on the unit.
8 Start recording on the digital audio device.
9 Stop recording on the digital audio device. Then press 8 to stop
Example: Dubbing to an MD
Recorder
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where you
intend editing to start, and where it actually starts.
Digital audio device
(MD deck, etc.)
Coaxial cable
(not provided)
To [DIGITAL AUDIO
OUT (COAXIAL)]
Player
46Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Rear of unit
Filename [MV5SEK_09Advanced Operation.fm]
MV5SEK_00.book Page 47 Wednesday, August 31, 2005 7:58 PM
Masterpage:Right0
ADVANCED PLAYBACK
47
Locating The Start Point Of The Item Or Skip The Item
Advanced Playback (DVD)
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
EN
Press 2 or 6 during playback.
● Pressing 6 locates the start point of the item or skips the item in
the forward direction, then resumes playback.
● Pressing 2 locates the start point of the item or skips the item in
the reverse direction, then resumes playback.
When a DVD-RAM/RW/R disc is played
Current programme
DVD
0–9
News
Previous
programme
Drama
Next
programme
Reverse
Movie
Forward
● : marked points (墌 pg. 49)
TOP MENU
ENTER
Example:
To locate the beginning of the next item, press 6 once.
To locate the beginning of the current item, press 2 once.
To locate the beginning of the previous item, press 2 three
times.
MENU
When a DVD VIDEO, Audio CD or Video CD disc is played
Playback point
Locating A Desired Scene Using The DVD Menu
Scene 2
(Chapter 2)
or
Track 2
Scene 3
(Chapter 3)
or
Track 3
Scene 4
(Chapter 4)
or
Track 4
DVD VIDEO discs may have top menu and disc menu.
Top menu
DVD discs generally have their own menus which show the disc
contents. These menus contain various items such as titles of a
movie, names of songs, or artist information. You can locate a
desired scene by using the top menu displayed on the TV screen.
Press TOP MENU to access the top menu.
Disc menu
Disc menus include playback data (angle menu, subtitle menu,
etc.) specific to each title.
Press MENU to access the disc menu.
1 Press TOP MENU or MENU to
Reverse
Forward
Example:
To locate the beginning of the next item, press 6 once.
To locate the beginning of the current item, press 2 once.
High-Speed Search
During playback, press 5 for forward high-speed search, or
3 for reverse high-speed search.
access the DVD menu.
2 Press rt w e to select a
desired title, then press ENTER.
Playback starts.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press 4.
NOTE:
For Audio CD
You can perform 4 levels of speed search with 5 and 3.
(Audio is active also during high-speed search.) You cannot
perform slow motion for each direction.
● It may be possible to select the
desired item using the number
buttons depending on the menu
display.
Example:
When “X” appears on the TV
screen in step 1, the disc does not have a top menu or disc menu.
47Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Left+
MV5SEK_00.book Page 48 Wednesday, August 31, 2005 7:58 PM
48
EN
ADVANCED PLAYBACK
Resume Function
It is possible to memorise the position where you stop playback
and resume playback from that position.
● Be sure to set “RESUME” to “ON” or “DISC RESUME”. (墌 pg. 80)
1 Press 8 during playback to memorise a resume point.
● The unit enters Resume Stop mode and memorises the position
where you have stopped playback as a resume point. (The inside of
the disc status indicator on the front display panel blinks while
memorising.)
● The unit retains a memory of the resume points of the last 30 discs
played back, even though they have been ejected if “RESUME” is set
to “DISC RESUME”. (墌 pg. 80)
● To clear the resume points:
(The inside of the disc status indicator stops blinking and lights.)
When “RESUME” is set to “ON”:
MARK
TOP MENU
ENTER
MENU
SLOW – (
)
SLOW + (
)
• Press 1 to turn off the unit.
• Press x (OPEN/CLOSE) to take out the disc.
• Press 8 in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
When “RESUME” is set to “DISC RESUME”:
REMAIN
ANGLE
SUBTITLE
Still Picture/Frame-By-Frame Playback
• Set “RESUME” to “OFF”. (墌 pg. 80)
• Press 8 in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
2 Press 4 in stop mode to resume playback. The unit starts
playback from the resume point.
NOTES:
1 Press 9 to pause during playback.
2 Press 9 repeatedly to activate frame-by-frame playback.
● Each press of w or e advances/reverses the still picture frame by
frame.
● Frame-by-frame playback for reverse direction cannot be performed
with Video CD discs.
● To resume normal playback, press 4.
Slow Motion
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5).
● Each press of SLOW – (3) or SLOW + (5) increases the slow
motion speed for each direction (from 1/16 to 1/2 times the normal
speed).
● Slow motion for reverse direction cannot be performed with Video CD
discs.
Skip Search
During playback, press
.
● Each press initiates an approximately 30-second period of fastmotion playback. Normal playback resumes automatically.
48Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
● “DISC RESUME” setting works on DVD VIDEO, VCD and already
finalised DVD-R/DVD-RW (video mode) discs. For other types of
discs, the function under “ON” setting will be applied even if
“RESUME” is set to “DISC RESUME”. (墌 pg. 80)
● If you stop the playback of a disc for which a resume point has
already been memorised, the memory will be updated with the new
resume point.
● After the unit has memorised the resume points for 30 discs,
remembering a new resume point will cause the unit to delete the
oldest memorised point. Stopping playback of a disc for which a
resume point is already stored may change the order in which the
points are stored. This may potentially change the order in which
points are deleted.
● When the unit memorises a resume point for a disc, it also
remembers audio language, subtitle and angle settings.
● This function may not work for some Video CDs.
● When “RESUME” is changed to “ON” or “OFF” (墌 pg. 80), resume
points of the discs memorised with “RESUME” set to “DISC
RESUME” will be cleared.
● Resume points are memorised for each side of a double-sided disc.
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Right+
MV5SEK_00.book Page 49 Wednesday, August 31, 2005 7:58 PM
ADVANCED PLAYBACK
Marking Positions To Play Back Again Later
It is possible to mark positions (up to 999 points) where you want
to play back once again later, and start playback from a marked
position. Marking onto DVD-RAM/RW (VR mode only) discs when
recording is helpful to locate a start point when you play back the
discs later.
To mark positions:
During playback, press MARK at
positions you want to mark.
● “MARK” appears on the TV screen.
You can easily locate the marked
positions using 2 or 6 when you
play back the disc.
To delete the marked positions:
While paused, press 2 or 6 to
locate a marked position you want to
delete, then press MARK.
When a PBC-compatible Video CD disc is loaded, deactivate the PBC
function. (墌 pg. 50)
Angle Selection
You can enjoy a variety of scene angles if a DVD VIDEO disc
contains “multi-angle” parts, where the same scene was shot from
different angles.
If the disc contains “multi-angle” parts, “
” appears on the TV
screen at the beginning of the “multi-angle” part.
1 Press ANGLE during playback.
NOTES:
2 Press ANGLE or w e to select
Checking The Time Information
You can check time information of a disc on the front display panel
and the TV screen.
Each press of DISPLAY changes the display as follows:
8 DVD-RAM/DVD-R/DVD-RW
During recording
Current title elapsed time ] Disc remaining time* ] Clock time
(front display panel only) ] (back to the beginning)
* only discs before finalising
● Clock time is displayed only when a recordable disc is recorded.
During playback
Current title elapsed time ] Disc remaining time* ] Each title
elapsed time ] (back to the beginning)
* only discs before finalising
In stop mode or during playback
● It is possible to check disc remaining time according to recording
modes also by pressing REMAIN.
● In FR mode, it is possible to set recording time in detail. While the
recording mode and the disc remaining time are displayed by
pressing REMAIN, press rt to select “FR”, then press w e to
select the desired recording time. (墌 pg. 62)
● It is not possible to switch the recording mode during playback or
while recording.
49Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
49
In stop mode
0:00 ] Playback time of track 1 ] 0:00 ] Total length of a disc ]
(back to the beginning)
NOTE:
● Crossed “MARK” appears on the TV
screen, and the marked position is
deleted.
● When a monaural or bilingual programme changes to a stereo
programme while recording, a mark signal is automatically recorded.
● Titles will be divided into “chapters” at the marked points according to
the disc types as follows:
DVD-R/RW (Video mode): After finalising, titles are divided into
“chapters” at the marked points that are marked automatically
approximately every 5 minutes during recording before finalising.
(墌 pg. 90)
DVD-RW (VR mode): After finalising, titles are divided into “chapters”
at the marked points that are marked at the desired locations during
playback before finalising. (墌 pg. 90)
DVD-RAM: Titles are divided into “chapters” at the marked points that
are marked at the desired locations during playback.
DVD VIDEO and finalised disc: Creating of marked points are not
permitted.
EN
8 Video CD/Audio CD
During playback
Current track elapsed time ] Current track remaining time ] Total
elapsed time ] Total remaining time ] (back to the beginning)
The angle selection display
appears on the TV screen.
When 3 scene angles are
contained.
your desired angle.
● Each time you press ANGLE or
w e, the angle changes.
● When “X” appears on the TV screen, the current scene is not
recorded from multiple angles. In addition, some discs prohibit angle
selection.
● To clear the angle selection display, press ENTER. In addition, the
angle selection display disappears automatically if no operation is
done for 10 seconds.
Subtitle Selection
Some DVD VIDEO discs contain more than one subtitle language,
from among which you can choose the desired subtitle language.
“ ” appears on the TV screen at the beginning of the part where
more than one subtitle language are recorded.
1 Press SUBTITLE during
playback. The subtitle selection
display appears on the TV screen.
● Each time you press SUBTITLE,
the subtitle display is switched on
and off.
ENGLISH
When 3 subtitle languages are
contained.
2 Press w e to select your desired language.
● To clear the subtitle selection display, press ENTER.
NOTES:
● When “X” appears on the TV screen, no subtitle language is
recorded.
● When the subtitle language won’t be changed with the procedure
above, change the subtitle on a disc menu displayed by pressing
MENU.
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Left+
MV5SEK_00.book Page 50 Wednesday, August 31, 2005 7:58 PM
50 EN ADVANCED PLAYBACK
Audio Language/Sound Selection
Playback Control (PBC) Function
Some DVD VIDEO discs contain the multiple audio language or
sound. You can select the desired audio language or sound. For
some Video CD discs, you can switch the audio channel to choose
Karaoke either with or without the vocal.
Some Video CD discs support the PBC function. PBC is an
abbreviation of “Play Back Control”. A Video CD disc recorded with
PBC has its own menus, such as a list of the songs on the disc.
You can locate a specific scene by using the menu.
1 Press AUDIO during playback.
1 Press 4 in stop mode. The PBC menu appears.
2 Press the number buttons to enter the number of the desired
The Audio Language/Sound
selection display appears.
2 Press AUDIO or w e to select
ENGLISH
When 3 audio languages are
contained.
scene. The unit starts playback of the selected item.
● Each time you press AUDIO or w e, the audio language/sound
changes.
● To clear the Audio Language/Sound selection display, press ENTER.
● “PBC” appears on the front display panel.
● When “NEXT” or “PREVIOUS” appears on the TV screen:
Pressing NEXT (6) advances to the next page.
Pressing PREVIOUS (2) returns to the previous page.
● You can return to the menu by pressing RETURN.
● The method of the operation is different depending on the disc.
NOTES:
NOTES:
your desired audio language/
sound.
● When “X” appears on the TV screen, no audio language is recorded.
● When the audio language won’t be changed with the procedure
above, change the audio on a disc menu displayed by pressing
MENU.
● Pressing AUDIO to select the audio language/sound is only possible
during playback. It is not possible to select by pressing AUDIO in stop
mode. However, you can select the desired audio language/sound
from the setup menu while in stop mode.
Audio Channel Selection
When watching bilingual programmes or playing discs on which
you recorded bilingual or stereo programmes, you can choose the
desired audio channel.
● When “SUPERIMPOSE” is set to “AUTO”, you can confirm on the TV
screen the audio channel you have chosen. (墌 pg. 79)
● Each time you press AUDIO, the audio channel
changes.
TRACK
USE
On-Screen Display
For main and sub audio of bilingual
programme
For main audio of bilingual programme
For sub audio of bilingual programme
For stereo discs
For audio of left channel
For audio of right channel
NOTE:
It is not possible for DVD-R/DVD-RW (Video mode) disc playback to
switch the audio channel.
When you can’t switch the audio channel of a bilingual
programme
When the unit is connected with a digital audio device using an
optional coaxial cable and “DIGITAL AUDIO OUT” is set to
“DOLBY DIGITAL/PCM”, it is not possible to switch the audio
channel of a bilingual programme recorded on a DVD-RAM or
DVD-RW (VR mode) disc. (墌 pg. 77) In this case, perform the
following steps using the remote control to switch “DIGITAL AUDIO
OUT” from “DOLBY DIGITAL/PCM” to “PCM ONLY”.
A Press SET UP to access the Main Menu screen.
B Press w e to select “DVD SET UP”, then press t.
C Press w e to select “AUDIO OUTPUT”, then press t.
D Press rt to select “DIGITAL AUDIO OUT”, then press ENTER.
E Press rt to select “PCM ONLY”, then press ENTER. (墌 pg. 78)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel.
50Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
● If you want to playback a PBC-compatible Video CD disc without
activating the PBC function, start playback in stop mode by using the
number buttons, instead of the 4 button, to choose the track, then
press ENTER.
● To activate the PBC function when a PBC-compatible Video CD disc
is being played back without the PBC function, press TOP MENU, or
press 8 then press 4.
Filename [MV5SEK_09Advanced Operation.fm]
MV5SEK_00.book Page 51 Wednesday, August 31, 2005 7:58 PM
Masterpage:Right+
ADVANCED PLAYBACK
51
Recording/Playback Status Display
Live Memory Playback
(DVD Deck Only)
●
●
●
●
EN
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
This unit records pictures onto the DVD-RAM discs, instead of
video tapes, then plays back the pictures recorded on the discs.
This makes it possible to achieve high-speed writing and read-out
that has not been possible with conventional VHSs, enabling
recording and playback simultaneously.
High-speed spin
Recording
(High-speed writing)
Playback
(High-speed read-out)
Image figure of DVD-RAM disc
It is called “Live Memory Playback” to start playback of the
programme being recorded, with a time-lag between a recording
point and a playback point, as shown in the figure below.
Current playback point
(Live Memory Playback)
Live Memory Playback status can be
checked by pressing DISPLAY to display
the bar meter on the superimpose display.
Current recording position
(Recording point)
Recording start point
Playback
continues
0
DISPLAY
30 min.
Recording
continues
1 hour
Currently elapsed recording time
Press DISPLAY. The current status is superimposed on the TV
screen.
Bar meter display
Not only can this unit play back a programme previously recorded
while recording or timer recording another programme, but the unit
also allows you to play back from the beginning of a programme
while continuing to record the same programme.
BBC1
Superimpose display
51Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Left+
MV5SEK_00.book Page 52 Wednesday, August 31, 2005 7:58 PM
52 EN ADVANCED PLAYBACK
Overview Of Live Memory Playback
You can play back a programme you are recording from the beginning while continuing to record or timer record onto a DVD-RAM disc.
This is called “Live Memory Playback”.
(Recording screen)
(Live Memory Playback screen)
To start Live Memory Playback,
press 4 to play back from the
beginning OR press
to
reverse-skip a little.
BBC1
To stop Live Memory
Playback, press 8.
Checking the
picture currently
being recorded
To clear, press
LIVE CHECK.
To stop recording,
press 8.
To display, press
LIVE CHECK.
(Playback and Live Check screen)
Recording
stops
To stop Live Memory Playback,
press 8.
BBC1
Live Memory Playback
picture
NOTES:
NAVIGATION
Press NAVIGATION to display Library Database
DVD Navi menu, then choose a programme to play
back. (墌 pg. 65)
ON SCREEN
LIVE CHECK
Pressing LIVE CHECK during Live Memory
Playback allows you to check the picture
currently being recorded.
52Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Recording
picture
● Live Memory Playback could be performed approximately 30
seconds after recording has started.
● Although high-speed search up to approximately 30 seconds before
the current recording point is possible during Live Memory
Playback, once the current recording point is reached, the unit
resumes normal playback and maintains a delay of approximately
30 seconds so that recording and playback can continue.
● When using Live Memory Playback during timer recording, playback
continues even after the end of the recording.
● When using Live Memory Playback during timer recording, playback
is automatically stopped just before recording starts, and then
recording starts when the time arrives for the next timer-programme.
● It is impossible to perform ITR even if you press 7 during Live
Memory Playback. (墌 pg. 51)
Press 8 to display the programme being recorded, then perform
ITR settings.
● Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
● Live Memory Playback cannot be performed while recording the
source from DV input. (墌 pg. 41, “DV Dubbing (DVD Deck Only)”)
● When LIVE CHECK is pressed to display the picture currently being
recorded, the picture size may not be correct.
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Right+
MV5SEK_00.book Page 53 Wednesday, August 31, 2005 7:58 PM
ADVANCED PLAYBACK
EN
53
Display During Live Memory Playback
During recording, you can watch at your will what was previously recorded or is currently being recorded. It is possible to perform freely
normal playback operations (forward/reverse high-speed search and variable-speed search) within the range of the red or blue bar on the
TV screen.
When Live Memory Playback reaches the point of 30 seconds before the current recording point by forward high-speed search or other
operations, the unit returns to normal playback.
The superimpose display appears by pressing ON SCREEN. (墌 pg. 12)
The Live Check picture is displayed on the bottom right corner by pressing LIVE CHECK.
Playback counter
Recording mode
Live Memory Playback mark
Recording title number
Playback title number
Recording counter display
(remaining/elapsed time)
Disc used
Present time
DVD-RAM
TITLE
9
0:14:55
XP
TITLE
9
22 : 0 0
PR 12
67
12:34:25
CHAPTER
EACH
KOALA
BBC1
Title name
Bar meter (see below)
Recording channel
Station Name
Playback mark
Recording mark
Live Check picture
Recording mark
This unit displays the current recording/playback status by the bar meter.
(Example of bar meter display)
Capacity of a disc
Not recorded
Recorded
While stopped
Total length of the programme being played
Current playback position
During playback
Capacity of a disc
Remaining capacity when recording started
Current recording position
While recording
Capacity of a disc
Recording start position
Current playback position
Current recording position
Live Memory Playback
Capacity of a disc
Recording start position
Current recording position
Current playback position
Live Memory Playback of
another programme
Total length of the programme being played back
Blue (recorded part)
Green (playing part)
Orange (recording part)
Black (unrecorded or unplayed part)
53Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Left+
MV5SEK_00.book Page 54 Wednesday, August 31, 2005 7:58 PM
54 EN ADVANCED PLAYBACK
Buttons To Be Used During Live Memory Playback
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
DVD
H
Pressing once skips forward for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips forward continuously as many times as
pressed.
It is useful when skipping over unwanted sections.
I
Pressing once skips back for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips back for approximately 7 seconds
continuously as many times as pressed.
It is useful when watching sports programmes, etc.
J LIVE CHECK
A
Pressing once displays the picture currently being recorded and
the one being played back simultaneously.
Pressing successively clears the Live Check window and displays
only the picture currently being played back.
You can check, for example, if the programme you are recording
has already finished.
To Play Back From The Beginning Of The Programme
While Recording
B
D
F
C
E
G
H
I
J
A NAVIGATION
Displays Library Database DVD Navi menu. You can choose a title
to play back.
B2
● Pressing once skips back to the beginning of the chapter being
played back.
● Pressing down for 2 or more seconds during playback reverses
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
Available only when paused
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed.
C6
● Pressing once skips forward to the beginning of the next chapter
being played back.
● Pressing down for 2 or more seconds during playback advances
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
You can play back a programme you are recording from the
beginning while continuing to record or timer record onto a DVDRAM disc.
Press 4. Live Memory Playback starts from the beginning of the
programme being recorded.
● Pressing 2 or 6 allows you to locate the desired scenes.
To Move Back The Playback Position Slightly While
Recording (One Touch Replay Function)
You can move back the playback position while continuing to
record or timer record onto a DVD-RAM disc.
Press
.
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds and
resumes pause.
To Watch A Programme Previously Recorded While
Recording
You can play back a programme you recorded previously while
recording.
Available only when paused
1 Press 4 during recording. Live Memory Playback starts.
2 Press 2 or 6 to locate the beginning of the desired
D3
programme.
NOTE:
● Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed.
● Each press of the button during playback advances the playback
speed in 5 steps in the reverse direction.
Available only when paused
● Pressing once reverses playback at 1/16 times the normal speed.
Then, each press of the button reverses slow-motion at 1/16 times, 1/4
times and 1/2 times the normal playback.
E5
● Each press of the button during playback advances the playback
speed in 4 steps in the forward direction.
Available only when paused
● Pressing once advances playback at 1/16 times the normal speed.
Then, each press of the button advances slow-motion at 1/16 times,
1/4 times and 1/2 times the normal playback.
F8
● Pressing once during Live Memory Playback returns to the screen on
air.
● Pressing twice during recording stops recording and returns to the
screen on air.
G9
Pressing once pauses playback (still picture playback). Pressing
repeatedly advances the still picture frame by frame.
54Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
To stop playback, press 8. The programme being recorded is
displayed.
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Right+
MV5SEK_00.book Page 55 Wednesday, August 31, 2005 7:58 PM
ADVANCED PLAYBACK
EN
55
JPEG disc
Using The On-screen Bar
A
JPEG
The on-screen bar allows you to control various playback
functions. Some of the functions operated on Navigation Menu can
be controlled on the On-screen bar.
Be sure to clear Library Database DVD Navi screen by pressing
NAVIGATION.
B
D
10 sec
K
A
B
C
D
E
F
G
H
I
J
K
Disc type.
Select this for Repeat Playback. (墌 pg. 56)
Select this for A-B Repeat Playback. (墌 pg. 56)
Select this for search function. (墌 pg. 56)
Select this for time search function. (墌 pg. 57)
Select this for Picture Control function. (墌 pg. 57)
Select this to switch picture source type. (墌 pg. 57)
Current status area for the selected item.
Select this for Programme Playback. (墌 pg. 58)
Select this for Random Playback. (墌 pg. 58)
Select this to control the switching interval of the slide show.
(墌 pg. 58)
NOTE:
Although examples of the on-screen bar are provided here only for 3
types of discs, the on-screen bar will be displayed for whichever disc
indicated in the left column.
Basic Operation On The On-screen Bar
Example: When selecting Picture Control function of DVD
During playback or while stopped
NAVIGATION
ENTER
1 Press ON SCREEN twice to access the on-screen bar. The item
currently selected is highlighted and pointed by H .
AUTO 1
DVD-VIDEO
2 Press w e to select “
”, then press ENTER. The pop-up
window appears under the selected item.
AUTO 1
DVD-VIDEO
ON SCREEN
3 Press rt to select the desired option, then press ENTER.
How To Access The On-screen Bar
DVD-VIDEO
1 Press ON SCREEN twice whenever a disc is loaded.
Contents of the on-screen bar during playback
DVD VIDEO
A
DVD-VIDEO
AUTO 1
AUTO 1
NORMAL
CINEMA
SHARP
SOFT
To clear the on-screen bar
Press ON SCREEN.
NOTE:
See the corresponding pages for details on each menu item.
B
C
D
E
F
G
Video CD
A
H
VIDEO-CD
CINEMA
B
C
D
E
I
J
F
55Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Left+
MV5SEK_00.book Page 56 Wednesday, August 31, 2005 7:58 PM
56
EN
ADVANCED PLAYBACK
A-B Repeat Playback
You can repeat the desired part.
During playback
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”.
3 Press ENTER at the beginning of the desired part you want to
0–9
repeat (point A). The elapsed playing time of the point A appears.
DVD-VIDEO
A
ENTER
CINEMA
0:16:58
AUTO 1
B
4 Press ENTER at the end of the desired part you want to repeat
(point B). The elapsed playing time of the point B appears.
● The selected part of the disc (between point A and B) is played
repeatedly.
DVD-VIDEO
A
ON SCREEN
CLEAR (8)
Repeat Playback
AUTO 1
0:16:58
B
0:17:45
To clear the on-screen bar
Press ON SCREEN.
To cancel A-B Repeat Playback
Press w e to select “
”, then press ENTER.
NOTES:
You can repeat playback as you like according to the type of disc.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
DVD-VIDEO
AUTO 1
3 Press rt repeatedly to select the desired Repeat mode, then
press ENTER.
DVD-RAM/RW/R
OFF: Repeat playback is not performed.
ALL REPEAT: The whole disc is played back repeatedly.
TITLE REPEAT: The current title is played back repeatedly.
DVD VIDEO
OFF: Repeat playback is not performed.
TITLE REPEAT: The current title is played back repeatedly.
CHAPTER REPEAT: The current chapter is played back repeatedly.
Audio CD/Video CD/JPEG/MP3
OFF: Repeat playback is not performed.
ALL REPEAT: The whole disc is played back repeatedly.
TRACK REPEAT*: The current track is played back repeatedly.
* “TRACK REPEAT” cannot be selected for JPEG discs.
To clear the on-screen bar
Press ON SCREEN.
To cancel Repeat Playback
Repeat the above procedure from step 1, select “OFF” in step 3,
then press ENTER.
NOTES:
● Repeat Playback is not possible for a Video CD with PBC function.
● Repeat Playback may not work properly depending on the type of the
disc being used.
56Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
● A-B Repeat Playback may not work properly depending on the type
of disc being used.
● The subtitles recorded around the A-B point may not appear.
● When the end of the item is reached before the end point is set, the
on-screen bar disappears from the TV screen. In such a case, repeat
the procedure from step 1.
● The point B must be set at least 3 seconds after the point A.
● When playing back a DVD, A-B Repeat Playback is possible only
within the same title.
●“
” cannot be selected during Programme and Random
Playback.
●“
” cannot be selected while stopped.
Locating The Beginning Of A Desired Selection
You can locate the beginning of a title, chapter, group or track.
During playback or while stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER.
3 Press rt to select the desired item, then press ENTER.
● Skip this step for Video CD and Audio CD.
For DVD-RAM/RW/R, DVD VIDEO
“TITLE SEARCH” or “CHAPTER SEARCH” is selectable. (“TITLE
SEARCH” is selectable only while stopped.)
For JPEG, MP3
“GROUP SEARCH” or “TRACK SEARCH” is selectable.
For Video CD, Audio CD
“TRACK” is selectable.
AUTO 1
DVD-VIDEO
TITLE SEARCH
CHAPTER SEARCH
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Right+
MV5SEK_00.book Page 57 Wednesday, August 31, 2005 7:58 PM
ADVANCED PLAYBACK
4 Press the number buttons to enter the desired item number,
then press ENTER.
EN
57
Adjusting The Picture Quality
● Playback starts from the selected section.
Examples:
A To select track 5, press the number button “5”.
B To select track 15, press the number button “1” and “5”.
C To select track 25, press the number button “2”, then “5”.
You can obtain optimal picture quality by selecting an appropriate
picture mode.
If you have specified a wrong selection
Press CLEAR (8) on the remote control unit and repeat the above
procedures from step 2.
window appears under the selected item.
To clear the on-screen bar
Press ON SCREEN.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER. The pop-up
DVD-VIDEO
NOTES:
AUTO 1
● When “X” is displayed on the TV screen in step 4, the chapter you
have selected is not contained in the disc, or chapter search does not
work on the disc.
● Before you press ENTER, playback may start automatically when
you enter the section’s number depending on the disc.
● This function is not possible for a Video CD with PBC function.
3 Press rt to select the desired option, then press ENTER.
Time Search
To clear the on-screen bar
Press ON SCREEN.
NORMAL: Normally select this option.
CINEMA: Suitable for a movie disc, etc.
SHARP: Clearer, sharper-edged picture when viewing images with
lots of flat, same-coloured surfaces such as cartoons.
SOFT: Select this option when too much noise appears.
Setting The Progressive Mode
You can play back a disc from the desired point by specifying the
elapsed playing time from the beginning of a programme (DVDRAM, DVD-R, DVD-RW and DVD VIDEO) or a disc (Video CD and
Audio CD).
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”, then press ENTER. The pop-up
window appears under the selected item.
DVD-VIDEO
TIME
AUTO 1
:
:
3 Press the number buttons to enter the time, then press
ENTER. Playback starts from the specified time.
Example:
To play back from a point 12 (minutes): 50 (seconds) elapsed.
TIME
Press 1
TIME
1 Set the unit to the progressive scan mode. (墌 pg. 80)
2 Press ON SCREEN twice to access the on-screen bar.
3 Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
ENTER
TIME
You can obtain optimal picture quality by selecting whether the
content on the disc is processed by field (video source) or by frame
(film source).
Press 2
TIME
Press 5
Press 0
TIME
If you have specified a wrong selection,
Press CLEAR (8) on the remote control unit and repeat the above
procedures from step 2.
To clear the on-screen bar
Press ON SCREEN.
NOTES:
● When “X” is displayed on the TV screen in step 3, you have selected
a point that exceeds the recording time of the disc.
● Some DVD VIDEO discs do not contain time information, and it is not
possible to use the Time Search function. In such cases, “X” is
displayed on the TV screen as well.
● This function is not possible for a Video CD with PBC function.
57Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
DVD-VIDEO
AUTO 2
4 Press rt to select the desired option, then press ENTER.
AUTO 1: Used to play a disc containing both video and film source
materials. This system recognises the source type (video or film)
of the current disc according to the disc information. Normally
select this option.
AUTO 2: Almost the same as the “AUTO 1”, but the processing of
the scenes with movement is different. Select “AUTO 1” or
“AUTO 2” to your preference.
FILM: Suitable for playing back a progressive scanned film source
disc.
VIDEO: Suitable for playing back a video source disc. The outlines
on the played back pictures will be soft.
To clear the on-screen bar
Press ON SCREEN.
NOTE:
When the progressive mode is set, be sure to set “L-1 OUTPUT” to
“COMPONENT”. (墌 pg. 44) Progressive scan is output only from
[COMPONENT VIDEO OUT] connector.
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Left+
MV5SEK_00.book Page 58 Wednesday, August 31, 2005 7:58 PM
58
EN
ADVANCED PLAYBACK
Random Playback
You can play back all the tracks on the disc in random order.
While stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “RND”, then press ENTER. Playback starts
0–9
in random order.
VIDEO-CD
CANCEL
RANDOM
To clear the on-screen bar
Press ON SCREEN.
ENTER
rtwe
RETURN
To cancel Random Playback
Perform steps 1 and 2.
NOTE:
The same track will not be played back more than once during Random
Playback.
Select The Switching Interval Of The Slide Show
ON SCREEN
CLEAR (8)
Programme Playback
You can control the switching interval of the slide show.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
You can programme up to 99 tracks (Video CD or Audio CD) to
play back in the desired order.
While stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “PRGM”, then press ENTER. The
programme table appears under on-screen bar.
VIDEO-CD
10 sec
3 Press rt to select the desired option, then press ENTER.
● Each time you press rt, the interval changes as follows:
5 SEC. { 10 SEC. { 15 SEC. { 20 SEC. { 25 SEC. {
30 SEC. { (Back to the beginning)
To clear the on-screen bar
Press ON SCREEN.
NOTE:
PROGRAMME
3 Press the number buttons to
JPEG
USE [0-9] KEYS TO SELECT TRACK
enter the track numbers in the
desired order.
Examples:
A To select track 5, press the
Programme Tota l Time
number button “5” and
ENTER.
B To select track 15, press the number button “1” and “5”.
C To select track 25, press the number button “2” and “5”.
If you have specified a wrong selection
Press CANCEL. The last selection is erased.
Or press CLEAR (8). The whole selection is erased.
4 Press 4. Playback starts in the programmed order.
● When all of the programmed tracks have been played back,
Programme Playback stops, but the programmed information
remains.
● To add tracks to the end of the programme, perform steps 1 through
3.
● During Programme Playback, pressing 6 skips to the next
selection of the programme. Pressing 2 returns to the beginning of
the current selection.
To clear the on-screen bar and the contents of the programme
Press ON SCREEN.
To cancel Programme Playback
Press w e to select “PRGM”, then press ENTER.
NOTE:
Programme Playback is not possible depending on the type of disc.
58Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
JPEG files are played back as a slide show. It may take more time to
display an image with larger file size.
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Right+
MV5SEK_00.book Page 59 Wednesday, August 31, 2005 7:58 PM
ADVANCED PLAYBACK
59
High-Speed Search
Advanced Playback (VHS)
●
●
●
●
EN
During playback, press 5 for forward high-speed search, or
3 for reverse high-speed search.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Press VHS so that the VHS lamp lights up on the unit.
VHS
● Each press of the button increases the search speed for each
direction.
When pressing 5:
(SP): +5x{+7x
(LP): +11x{+21x
When pressing 3:
Once 3 is pressed, reverse search starts in –1x normal playback
speed. After this process, each press of 3 changes the search
speed between –5x and –7x in SP mode, –11x and –21x in LP mode.
(SP): –1x]–5x{–7x
(LP): –1x]–11x{–21x
● To resume normal playback, press 4.
Quick Rewind A Little
PR +/–
During playback, press
. The unit rewinds the picture a little
(about 7 seconds) and resumes playback.
● If the button is pressed repeatedly, the unit rewinds the pictures
continuously and resumes playback.
Skip Search
During playback, press
sections.
1 to 6 times to skip over unwanted
● Each press initiates an approximately 30-second period of fastmotion playback. Normal playback resumes automatically.
● To resume normal playback, press 4.
Index Search
Your unit automatically marks index codes at the beginning of each
recording. This function gives you quick access to any one of the 9
index codes in either direction.
Clean the video heads using a dry cleaning cassette when:
● Rough, poor picture appears while a tape is played back.
● The picture is unclear or no picture appears.
● “USE CLEANING CASSETTE” appears on the screen (only with
“SUPERIMPOSE” set to “AUTO”). (墌 pg. 79)
NOTE:
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or humidity
● in a dusty environment
● flaw, dirt or mold on video tapes
● continuous usage for a long time
ATTENTION:
In the search, still, slow-motion or frame-by-frame playback mode,
● the picture will be distorted.
● the noise bars will appear.
● there may be a loss of colour.
● you cannot hear the sound.
NOTE:
Before starting, make sure the unit is in the Stop mode.
Press 2 or 6 to activate Index Search. “2 1” or “6 1” is
displayed on the TV screen and search begins in the corresponding
direction.
● To access index codes 2 through 9, press 2 or 6 repeatedly
until the correct index number is displayed.
Example:
To locate the beginning of B from the current position, press 2
twice.
To locate the beginning of D from the current position, press 6
once.
Current position
Still Picture/Frame-By-Frame Playback
1 Press 9 to pause during playback.
● If there is vertical jitter, press PR +/– to correct the picture.
2 Press 9 repeatedly to activate frame-by-frame playback.
● To resume normal playback, press 4.
Slow Motion
1 Press 9 to pause during playback.
2 Press and hold 9 for 2 seconds, then release. Press 9 and
release again to return to still picture.
● To resume normal playback, press 4.
NOTE:
During slow motion playback, some noise may appear on the TV
screen. Press PR + or – to eliminate the noises.
59Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Index number
● When the specified index code is located, playback begins
automatically.
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Left+
MV5SEK_00.book Page 60 Wednesday, August 31, 2005 7:58 PM
60 EN ADVANCED PLAYBACK
Next Function Memory
The Next Function Memory “tells” the unit what to do after
rewinding. Before continuing, make sure the unit is in the Stop
mode.
For Automatic Start Of Playback
Press 3, then press 4 within 2 seconds.
For Automatic Cassette Ejection
Press 3, then press x (EJECT) within 2 seconds.
Soundtrack Selection
Your unit is capable of recording three soundtracks (HI-FI L, HIFI R and NORM) and will play back the one you select.
During Playback
Pressing AUDIO changes the soundtrack as follows:
TRACK
Repeat Playback
HI FI
LjhR
Your unit can automatically play back the whole tape 100 times
repeatedly.
HI FI
Lj
1 Press 4 to start playback.
2 Press and hold 4 for over 5 seconds, then release.
HI FI
hR
●“
” lights up on the front display panel.
● After playing back a tape 100 times, the unit stops automatically.
3 Press 8 at any time to stop Repeat Playback.
● Pressing 4, 3, 5 or 9 also stops Repeat Playback.
Manual Tracking
Your unit is equipped with automatic tracking control. During
playback, you can override this and adjust the tracking manually by
pressing the PR buttons.
USE
On-Screen Display
For Hi-Fi stereo tapes
For main audio of Bilingual tapes
For sub audio of Bilingual tapes
NORM
For audio-dubbed tapes
HI FI
NORM
For audio-dubbed tapes
NOTES:
● “HI FI L j h R” should normally be selected. In this mode, Hi-Fi
stereo tapes are played back in stereo, and the normal audio track is
played back automatically for tapes with only normal audio.
● For instructions on recording stereo and bilingual programmes, refer
to page 64.
● “SUPERIMPOSE” must be set to “AUTO” or the on-screen displays
will not appear. (墌 pg. 79)
VHS Progressive Scan
1 During playback, press PR + or – on the unit simultaneously to
activate manual tracking.
2 Press PR + or – to adjust the tracking manually.
● To return to automatic tracking, press PR + or – simultaneously
or eject and insert the tape again.
NOTE:
When a new tape is inserted, the unit enters the automatic tracking
mode automatically.
You can watch the images on VHS deck in the Progressive scan
mode via component video.
ATTENTION:
● Your TV needs to be compatible with Progressive and to have
Component video input connectors.
● Make sure that there is no disc in the unit.
1 Set the Progressive-compatible TV to the component input
mode.
2 Press DVD so that the DVD lamp lights up on the unit.
3 Press PROGRESSIVE SCAN for 3 or more seconds.
● The video output indicator
lights up on the front display panel.
4 Press VHS so that the VHS lamp lights up on the unit, then
press PROGRESSIVE SCAN.
● “]” lights up on the unit.
NOTES:
● Be sure to engage the DVD deck in stop mode.
● During still picture in VHS Progressive Scan mode, the images may
jitter, but this is not a malfunction.
60Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Right0
MV5SEK_00.book Page 61 Wednesday, August 31, 2005 7:58 PM
ADVANCED RECORDING
61
Instant Timer Recording (ITR)
Advanced Recording (DVD)
●
●
●
●
EN
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
1 Press 7 on the unit to start recording.
2 Press 7 again to engage the ITR mode.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
● On the front display panel, “0:30” appears.
3 If you want to record for more than 30 minutes, press 7 to
extend the time. Each press extends recording time by 30 minutes.
NOTE:
You can only perform ITR using the 7 button on the unit.
Watch Another Programme While Recording On The Unit
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
While recording is going on, you can watch another programme on
the TV by using the TV’s tuner.
NOTE:
It is required that the remote control is set to be able to operate the TV
in advance. (墌 pg. 75)
1 During recording, press TV/VIDEO to switch the TV’s input
mode so that the programme selected on the TV appears.
DVD
TV/VIDEO
2 Slide the TV/DVD switch to TV.
3 Press PR +/– repeatedly to select the desired channel.
NOTE:
If a decoder is connected to the unit (墌 pg. 76), you can select a
scrambled channel as well as other normal channels.
PR +/–
Elapsed Recording Time And Disc Remaining Time
Indication
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time ] Disc remaining time ] Clock ] (Back to
the beginning)
● You can also check the disc remaining time by pressing REMAIN
while the unit is stopped or recording is in progress. The list of disc
remaining times for all recording modes appears on the TV screen.
REMAIN
DISPLAY
61Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Left+
MV5SEK_00.book Page 62 Wednesday, August 31, 2005 7:58 PM
62 EN ADVANCED RECORDING
Free Rate Function
Receiving Stereo And Bilingual Programmes
To record the entire programme, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the programme to be recorded and either the
remaining disc space or the specified recording time (from 60
minutes to 480 minutes).
8 To record the entire programme within the actual
remaining disc space
Select “FR (JUST)” in a recording mode selection procedure.
● Note that this function is available only for timer programming
recording (墌 pg. 29, 31).
8 To record the entire programme by specifying the desired
recording time
Select “FR60–FR360”, “FR420” or “FR480” in a recording mode
selection procedure. (墌 pg. 26, 29, 31)
8 To record a 25-min. long daily programme five times just
on the same DVD disc for example
Perform “VIDEO Plus+ Timer Programming” (墌 pg. 29) procedure.
Be sure to set the recording mode to “FR125” and set Weekly/Daily
Rec Function to “MON–FRI” in step 6 to fit the total recording time
to the whole disc space.
Blank
A: 1st
B: 2nd
C: 3rd
D: 4th
E: 5th
When the same programme is recorded in SP mode instead of in
“FR125”, the 5th programme cannot be recorded.
Blank
NOTES:
A: 1st
B: 2nd
C: 3rd
D: 4th
E: Blank (20 min.)
● You can programme this unit to timer-record, regardless of the disc
remaining time. When the disc remaining time is not enough,
recording may stop in the middle of a programme. To avoid this,
make sure of the disc remaining time before setting timer
programming.
(Example) If you programmed to timer-record for 60 minutes in SP
mode on a 120-minute disc, the disc remaining time would be 30
minutes in XP mode, 60 minutes in SP mode, 120 minutes in LP
mode, 180 minutes in EP mode, and 240 minutes in FR480 mode.
Timer-recording will not complete beyond these remaining times.
● The maximum recording time of “FR (JUST)” mode is the same as
the recording time of FR480 mode. When timer programming a long
programme in “FR (JUST)” mode on a disc whose remaining time is
short, it is recommended to check the disc remaining time in FR480
mode to see if the remaining time is enough for the programme.
● Even if more than one programme are timer programmed in “FR
(JUST)” mode, only the first one is recorded.
● In order to ensure that the recording fits on the disc, this feature may
leave a slight non-recorded section at the end of the disc.
● There may be some noise and sound disturbance at the point on the
disc where the unit switches the mode.
62Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Your unit is equipped with a Digital stereo sound decoder (NICAM)
making reception of stereo and bilingual broadcasts possible.
When the channel is changed, the type of broadcast being
received will be displayed on the TV screen for a few seconds.
Type of Broadcast Being
Received
On-screen Display
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
NOTES:
● “SUPERIMPOSE” must be set to “AUTO”. Otherwise the on-screen
displays will not appear. (墌 pg. 79)
● If the quality of stereo sound being received is poor, the broadcast
might be received in monaural with better quality.
Selection Of The Audio Channel To Be Recorded On A
Disc
When a programme is recorded on a DVD-RAM or DVD-RW disc
in VR mode, all audio channels of the receiving programme are
recorded on the disc. When you record a programme on a DVD-R
or DVD-RW disc in video mode, select the desired audio channel
(from among “NICAM 1/MAIN”, “NICAM 2/SUB”, “MONO”) to be
recorded on the disc. (墌 pg. 79)
NOTE:
Before playing back a programme recorded in stereo, or a bilingual
programme, refer to “Audio Channel Selection” on page 50.
Filename [MV5SEK_09Advanced Operation.fm]
Masterpage:Right+
MV5SEK_00.book Page 63 Wednesday, August 31, 2005 7:58 PM
ADVANCED RECORDING
Advanced Recording (VHS)
●
●
●
●
EN
63
Accidental erasure prevention
To prevent accidental recording on
a recorded cassette, remove its
safety tab. To record on it later,
cover the hole with adhesive tape.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Press VHS so that the VHS lamp lights up on the unit.
Record safety tab
Watch Another Programme While Recording On The Unit
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
While recording is going on, you can watch another programme on
the TV by using the TV’s tuner.
NOTE:
It is required that the remote control is set to be able to operate the TV
in advance. (墌 pg. 75)
1 During recording, press TV/VIDEO to switch the TV’s input
mode so that the programme selected on the TV appears.
VHS
TV/VIDEO
2 Slide the TV/DVD switch to TV.
3 Press PR +/– repeatedly to select the desired channel.
NOTE:
If a decoder is connected to the unit (墌 pg. 76), you can select a
scrambled channel as well as other normal channels.
0000
PR +/–
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
1 Press 7 on the unit to start recording.
2 Press 7 again to engage the ITR mode.
● On the front display panel, “0:30” appears.
3 If you want to record for more than 30 minutes, press 7 to
extend the time. Each press extends recording time by 30 minutes.
NOTES:
DISPLAY
● You can only perform ITR using the 7 button on the unit.
● During Instant Timer Recording, any other timer programmed
recording won’t start even if their start time has come. In such a case,
the timer programmed recording starts (if the end time of the timer
programmed recording is set after the end of Instant Timer
Recording) after the Instant Timer Recording finishes.
Elapsed Recording Time Indication
1 Press DISPLAY until a counter reading appears on the front
display panel.
2 Press 0000 to reset the counter before starting recording or
playback.
● The counter is reset to “0:00:00” and shows the exact elapsed time
as the tape runs. You can check the exact time of a recording or
playback.
63Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_09Advanced Operation.fm]
MV5SEK_00.book Page 64 Wednesday, August 31, 2005 7:58 PM
64 EN ADVANCED RECORDING
Tape Remaining Time
Masterpage:Left+
B.E.S.T. Picture System
1 Press DISPLAY until the time remaining on the tape appears.
● By pressing the DISPLAY button, you can change display to show
the clock time, counter reading or tape remaining time.
NOTE:
Depending on the type of tape being used, the tape remaining time
reading may not appear right away, or is not correct.
“– –:– –” may sometimes appear, or the display may blink on occasion.
Receiving Stereo And Bilingual Programmes
Your unit is equipped with a Digital stereo sound decoder (NICAM)
making reception of stereo and bilingual broadcasts possible.
When the channel is changed, the type of broadcast being
received will be displayed on the TV screen for a few seconds.
Type of Broadcast Being
Received
On-screen Display
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
(none)
ST NICAM
BIL. NICAM
NICAM
● To listen to a stereo programme, press AUDIO until “HI FI L j h R”
appears on the TV screen.
● To listen to a bilingual programme, press AUDIO until “HI FI L j” or
“HI FI h R” appears on the TV screen.
● To listen to the standard (Regular Monaural) audio while receiving a
NICAM broadcast, press AUDIO until “NORM” appears on the TV
screen.
NOTE:
“SUPERIMPOSE” must be set to “ON”, or the on-screen displays will
not appear. (墌 pg. 79)
To Record Stereo and Bilingual Programmes (A2)
Stereo programmes are automatically recorded in stereo on the
Hi-Fi audio track (with the normal audio track recording mixed L
and R channel sound).
● Bilingual programmes are automatically recorded in bilingual on the
Hi-Fi audio track. The main soundtrack will be recorded on the
normal audio track.
To Record NICAM Stereo and Bilingual Programmes
The NICAM audio programme will be recorded on the Hi-Fi audio
track, and the standard audio programme will be recorded on the
normal audio track.
NOTES:
● If the quality of stereo sound being received is poor, the broadcast
will be received in monaural with better quality.
● Before playing back a programme recorded in stereo, or a bilingual
programme, refer to “Soundtrack Selection” on page 60.
64Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
The B.E.S.T. (Biconditional Equalised Signal Tracking) system
checks the condition of the tape in use during playback and
recording, and compensates to provide the highest-possible
playback and recording pictures. You can set “B.E.S.T.” to “ON” or
“OFF” to your preference. (墌 pg. 81)
Playback
The unit assesses the quality of the tape once you initiate
playback.
● The unit adjusts the playback picture quality based on the quality of
the tape in use.
● B.E.S.T. is active during automatic tracking. “BEST” appears blinking
on the front display panel.
● “BEST” only appears at the beginning of automatic tracking. Even
though it doesn’t appear after that, the B.E.S.T. function is operative.
Recording
The unit assesses the quality of the tape once you initiate
recording.
● The unit spends approximately 7 seconds assessing the condition of
the tape, then begins recording.
ATTENTION:
Since the B.E.S.T. system works before recording actually starts,
there is a delay of approximately 7 seconds after 7 and 4 on the
remote control are pressed, or 7 on the unit is pressed. To make
sure you record the desired scene or programme in its entirety, first
perform the following steps:
A Press and hold 9 and press 7 to engage the Record Pause
mode.
● The unit then automatically checks the condition of the tape and,
after approximately 7 seconds, re-enters Record Pause mode.
B Press 4 to start recording.
If you want to bypass the B.E.S.T. system and begin recording
immediately, set “B.E.S.T.” to “OFF”. (墌 pg. 81)
Filename [MV5SEK_10Navigation.fm]
Masterpage:Right0
MV5SEK_00.book Page 65 Wednesday, August 31, 2005 7:58 PM
NAVIGATION (DVD DECK ONLY)
Library Database DVD Navi
The Library Database DVD Navi enables you to search and select
the desired titles recorded on a DVD-RAM/R/RW disc very easily.
You can record up to 99 titles on a disc.
Each time a title is recorded on the disc, the information of the title
is registered for the Library Database DVD Navi automatically.
So, you can confirm the information of the titles recorded on the
disc with the Library Database DVD Navi screen. And, you can
also select one of the titles recorded using the Library Database
DVD Navi.
The following screen appears as the Library Database DVD Navi
screen when you press NAVIGATION. You can move the arrow to
select the desired position on the screen by pressing rt w e on
the remote control.
A
B
ORIGINAL
PLAY LIST
LIBRARY
REMAIN TIME
0001
1
CD E
2
87min(SP)
3
1/6
4
DANCE
DANCE CURNIV
28/07/03 MON10:00 - 11:00
MODIFY
OK
SELECT
F
DELETE
NAVIGATION
EXIT
PR.7CH SP
EDITING
[OTHERS]
60min
PROTECT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
G
H
A Index
B
C
D
E
F
G
H
(Small still picture of each title)
Names of functions
ORIGINAL (墌 pg. 66)
PLAY LIST (墌 pg. 68)
LIBRARY (墌 pg. 71)
Remaining time
(Based on the recording mode currently selected)
Current/Total number of title(s)
(For example, there are 6 recorded titles and the title indicated
by the arrow is the 3rd one.)
Icons
(Indicate the recording condition for each title.)
Recording information for the title indicated by the arrow
Guidance for operations
Operational commands
EN
65
Using Library Database DVD Navi system, you can easily modify
registered information, edit the title or play list, as well as search
for the beginning of each title.
About registration of information
The following information is automatically registered for each title
when ordinary recording or timer recording is performed, then
stored in an area specified on the unit.
●
●
●
●
●
●
●
index* (reduced still pictures to show programme titles)
programme title*
category*
date and time
channel
recording mode
length of recording time
The items marked with an asterisk (*) can be easily modified and
registered again after recording by using Library Database DVD
Navi system.
About editing of titles
Library Database DVD Navi system has the following functions for
editing of titles.
● “Modify Play List Information” (墌 pg. 68)
● “Delete Title” (墌 pg. 67)
The limitations of registration
You can register information up to 99 titles.
When the amount of information is at the limits of registration, you
cannot record new title any more. In this case, you need to delete
old titles to register new one. (墌 pg. 67)
NOTE:
Once a DVD-R/RW (Video mode) disc has been finalised, the displays
for original and play list do not appear. Only display for library appears.
The display for original
recording
ORIGINAL
PLAY LIST
LIBRARY
REMAIN TIME
0001
1
2
3
The display for play list
ORIGINAL
87min(SP)
4
PLAY LIST
LIBRARY
0001
1
2
3
4
DANCE
DANCE CURNIV
28/07/03 MON 10:00 - 11:00
MODIFY
OK
SELECT
DELETE
NAVIGATION
EXIT
PR. 7CH SP
EDITING
[OTHERS]
60min
PROTECT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
[OTHERS]
28/07/03 MON
MODIFY
OK
SELECT
DELETE
NAVIGATION
EXIT
EDITING
CREATE
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
The Icons and their meanings
This title is write-protected.
This title has stereo sounds.
This title has bilingual sounds.
This title was recorded with timer recording.
65
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_10Navigation.fm]
Masterpage:Left+
MV5SEK_00.book Page 66 Wednesday, August 31, 2005 7:58 PM
66 EN NAVIGATION (DVD DECK ONLY)
Scan For Beginning Of Title
Modify Original Information
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
PR +/–
MEMO
NAVIGATION
ENTER
NAVIGATION
ENTER
CLEAR (
rtwe
)
You can scan the beginning of the title easily with the Library
Database DVD Navi.
1 Load a recorded disc.
2 Press NAVIGATION. The Library Database DVD Navi screen
appears.
3 Press rt w e to select
ORIGINAL
“ORIGINAL”, then press ENTER.
LIBRARY
REMAIN TIME
0001
1
4 Press w e to select the index
(small still pictures) of the desired
title.
PLAY LIST
2
3
87min(SP)
4
DANCE
DANCE CURNIV
28/07/03 MON 10:00 - 11:00
PR. 7CH SP
[OTHERS]
60min
● You can press PR + or – to show
MODIFY
DELETE
EDITING
PROTECT
OK
other pages.
NAVIGATION
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
EXIT
SELECT
● When you want the plural titles to
be played back continuously,
press MEMO after selecting the desired title. The numbers of the
playback order appear on the index. You can select up to 30 titles.
● When you want to correct the order, move the arrow to the desired
index and press MEMO. The number disappears and the unit renumbers the other titles automatically.
● When you want to cancel the order, press CLEAR (8).
Modify Index
1 Press NAVIGATION. The Library Database DVD Navi screen
appears.
2 Press rt w e to select “ORIGINAL”, then press ENTER.
3 Press rt w e to select one title you want to modify, then press
t.
4 Press rt w e to select “MODIFY”, then press ENTER.
5 Press w e to select “MODIFY INDEX”.
6 Search for the picture from the
MODIFY INDEX
MODIFY NAME
title by pressing the appropriate
buttons (3, 4, 5, or 9). The
pictures of the title appear on the
left window.
MODIFY CATEGORY
REPLACE
00:05:00
00:00:21
[OTHERS]
60min
5 Press 4 to start playback.
6 Press 9 to pause playback.
7 Confirm the arrow is on
7 Press 8 to stop playback.
● When you press ENTER with the arrow on “RETURN” you can return
to the previous screen.
● To resume normal playback, press 4.
28/07/03 MON 10:00 - 11:00
RETURN
“REPLACE”, then press ENTER
to register new index. New index
appears on the right window.
OK
SELECT
NAVIGATION
EXIT
PR.7CH SP
SELECT SCENE WITH [PLAY/PA USE etc.]
THEN PRESS [ENTER]
8 Press NAVIGATION to return to the normal screen.
● Press 8 to cancel pause mode after pressing NAVIGATION.
66
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_10Navigation.fm]
Masterpage:Right+
MV5SEK_00.book Page 67 Wednesday, August 31, 2005 7:58 PM
NAVIGATION (DVD DECK ONLY)
67
EN
Modify Title Name
Delete Title
1 Perform steps 1 to 3 of “Modify Index” (墌 pg. 66) before
continuing.
You cannot record any more with Library Database DVD Navi once
the registered titles on the disc reach 99 titles. Deleting
unnecessary titles after dubbing or other operations can increase
remaining time and available recording capacity. (For DVD-R discs,
although it is possible to delete recorded titles, available recording
capacity does not increase.) The deleted title is never resumed.
Play lists and programme information in the unit’s library are also
deleted.
2 Press rt w e to select “MODIFY”, then press ENTER.
3 Press w e to select “MODIFY NAME”.
4 Press rt w e to select the
MODIFY INDEX
desired letter or command, then
press ENTER. Repeat this
process to complete the name.
MODIFY NAME
MODIFY CATEGORY
DANCE CURNIV
DELETE
A
B
J
K
DELETE ALL
C
D
E
F
G
H
I
1
2
3
!
L
M
N
O
P
Q
R
4
5
6
&
"
'
#
$
(
)
%
● To correct a letter, press rt w e
DANCE CURNIV
[OTHERS]
28/07/03 MON 10:00 - 11:00 PR.7CH SP 60min
to select “DELETE” or “DELETE
RETURN
SAVE
ALL”, then press ENTER.
OK
NAVIGATION ENTER NAME WITH [0 - 9] KEYS
● You can enter the letters up to 64. SELECT
THEN SELECT “SAVE”
EXIT
● You can also enter the new name
with the number buttons. For
example, when you press 2 repeatedly, “A”, “B”, “C”, “a”, “b”, “c”, “2”,
and then “A” appear by turns. You can use the following buttons.
S
T
U
V W X
Y
Z
7
8
9
0
+
-
Number buttons: for entering letters, numbers and blank space
w e buttons: for moving the entering or inserting point
CLEAR (8) button: for correcting a letter
2/6 buttons: for changing character tables
5 Press rt w e to select “SAVE”, then press ENTER.
6 Press rt w e to select “RETURN”, then press ENTER. The
1 Perform steps 1 to 2 of “Modify Index” (墌 pg. 66) before
continuing.
2 Press rt w e to select one title you want to delete, then press
t.
3 Press rt w e to select “DELETE”, then press ENTER. The
message appears for your confirmation.
4 Press w e to select “YES”, then press ENTER.
● When you cancel the deletion, select “NO”, then press ENTER.
5 Press NAVIGATION to return to the normal screen.
Delete Unwanted Part Of The Title (DVD-RAM/DVDRW (VR mode))
You can delete unwanted part of the title.
1 Perform steps 1 to 2 of “Modify Index” (墌 pg. 66) before
Library Database DVD Navi screen appears again.
continuing.
7 Press NAVIGATION to return to the normal screen.
2 Press w e to select one title whose unwanted part you want to
Modify Category
3 Press w e to select “EDITING”, then press ENTER.
4 Press 4 to start playback. The playback pictures appear in the
delete, then press t.
1 Perform steps 1 to 3 of “Modify Index” (墌 pg. 66) before
continuing.
window on the screen. The elapsed playing time starts counting
with the arrow on “IN”.
2 Press rt w e to select “MODIFY”, then press ENTER.
3 Press w e to select “MODIFY CATEGORY”.
4 Press rt w e to select the
MODIFY INDEX
desired category, then press
ENTER.
5 Press ENTER. The Library
Database DVD Navi screen
appears again.
6 Press NAVIGATION to return
to the normal screen.
MOVIES
SPORTS
EDUCATION
SHOPPING
MODIFY NAME
MUSIC
DOCUMENTARY
HOBBY
OTHERS
DANCE CURNIV
28/07/03 MON 10:00 - 11:00
5 Find the point where you want
MODIFY CATEGORY
DRAMA
NEWS
ENTERTAINMENT
PR.7CH SP
ANIMATION
WEATHER
ART
[OTHERS]
60min
RETURN
OK
SELECT
NAVIGATION
EXIT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
the deletion to begin, then press
ENTER with the arrow on “IN”.
The edit-in time is fixed and the
elapsed playing time starts
counting again.
6 Find the point where you want
the deletion to end, then press
ENTER with the arrow on “OUT”.
The edit-out time is fixed.
DELETE SCENE
IN
OUT
A
0:00:29:24
A
IN
-:--:--:-: : :
OUT
TOTAL TIME
TITLE 05 CHAPTER 01
TIME 0000:00:53 **
RETURN
OK
SELECT
PREVIEW
NAVIGATION
EXIT
EXECUTE
CLEAR
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in and edit-out
points.
Protect Title (DVD-RAM/DVD-RW (VR mode))
7 Press rt w e to select “PREVIEW”, then press ENTER to
preview the edited title.
You can protect titles to prevent accidental erasure of the
important titles.
8 Press rt w e to select “EXECUTE”, then press ENTER.
1 Perform steps 1 to 2 of “Modify Index” (墌 pg. 66) before
continuing.
● If you do not want to delete the scene, select “CLEAR” and press
ENTER.
2 Press rt w e to select a title you want to protect, then press
9 Press w e to select “YES”, then press ENTER. The selected
scene is deleted.
t.
3 Press w e to select “PROTECT”, then press ENTER. “
”
appears.
● To cancel the protection, repeat 2 – 3 again.
4 Press NAVIGATION to return to the normal screen.
● To cancel the deletion, press w e to select “NO”, then press ENTER.
To modify the points
A Press w e to select “CLEAR”, then press ENTER.
B Repeat steps 4 – 9 as necessary.
NOTE:
10 Press NAVIGATION to return to the normal screen.
All the titles on a disc will be deleted once the disc is formatted even if
they are protected titles. (墌 pg. 67)
NOTES:
67
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
● There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
● Available recording capacity may not match the deleted part after
deletion.
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_10Navigation.fm]
Masterpage:Left+
MV5SEK_00.book Page 68 Wednesday, August 31, 2005 7:58 PM
68
EN
NAVIGATION (DVD DECK ONLY)
8 Press w e to select “PREVIEW”, then press ENTER to preview
Modify Play List Information
the play list.
9 Press w e to select “EXECUTE”, then press ENTER. The play
list is created.
To modify the points
A Press w e to select “CLEAR”, then press ENTER.
B Repeat steps 5 – 9 as necessary.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
10 Press NAVIGATION to return to the normal screen.
NOTES:
● There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
● The title, index and category of the play list can be modified in the
same way as “ORIGINAL”. (墌 pg. 66)
● You can modify the play list that has just been created here by
adding, moving, or deleting unwanted parts to create a digest edition,
etc.
Add Scenes To A Play List
1 Perform steps 1 to 3 of “Create Play List” (墌 pg. 68) before
PR +/–
continuing.
2 Press w e to select the play list to which you wish to add a
MEMO
scene, then press t.
3 Press w e to select “EDITING”, then press ENTER.
4 Press w e to select “ADD
NAVIGATION
ENTER
DELETE SCENE
rtwe
MOVE SCENE
ADD SCENE
SCENE”.
IN
5 Press 4 to start playback. The
playback pictures appear in the
window on the screen. The
elapsed playing time starts
counting with the arrow on “IN”.
● To locate the beginning of other
titles, press 2/6.
Play List
It is a collection of the scenes. A play list can be freely edited and
played back without ever changing any original recording data.
Using the random access of a DVD disc (which allows video data
to be instantly read no matter where it is on the disc), a play list
includes information such as the timer counter for the playback
start point and end point, indexes for checking the contents of
recorded data, category information, and more. Playback
according to a play list you have created allows you to enjoy
various combinations of video images from a single title.
Create Play List
OUT
-:--:--:--
IN
-:--:--:-: : :
OUT
TOTAL TIME
TITLE 05 CHAPTER 01
TIME 0000:00:53 **
RETURN
OK
SELECT
PREVIEW
NAVIGATION
EXIT
EXECUTE
CLEAR
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
6 Find the point where you want the added scene to begin, then
press ENTER with the arrow on “IN”. The edit-in time is fixed and
the elapsed playing time starts counting again.
7 Find the point where you want the added scene to end, then
press ENTER with the arrow on “OUT”. The edit-out time is fixed.
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in and edit-out
points.
8 Press w e to select “PREVIEW”, then press ENTER to preview
approximately 5 seconds before and after the edited scene.
9 Press w e to select “EXECUTE”, then press ENTER. The
selected scene is added.
1 Load a DVD-RAM or DVD-RW (VR mode) disc that was
recorded with this unit.
To modify the points
A Press w e to select “CLEAR”, then press ENTER.
B Repeat steps 5 – 9 as necessary.
2 Press NAVIGATION. The Library Database DVD Navi screen
10 Press NAVIGATION to return to the normal screen.
appears.
NOTE:
3 Press rt w e to select “PLAY LIST”, then press t or ENTER.
4 Press rt w e to select “CREATE”, then press ENTER.
5 Press 4 to start playback. The playback pictures appear in the
There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
window on the screen. The elapsed playing time starts counting
with the arrow on “IN”.
● To locate the beginning of other titles, press 2/6.
6 Find the point where you want
the created play list to begin, then
press ENTER with the arrow on
“IN”. The edit-in time is fixed and
the elapsed playing time starts
counting again.
7 Find the point where you want
the created play list to end, then
press ENTER with the arrow on
“OUT”. The edit-out time is fixed.
CREATE
IN
OUT
A
A
0:00:29:24
IN
-:--:--:-: : :
OUT
TOTAL TIME
TITLE 05 CHAPTER 01
TIME 0000:00:53 **
RETURN
OK
SELECT
PREVIEW
NAVIGATION
EXIT
EXECUTE
CLEAR
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in and edit-out
points.
● The edit-out point must come after the edit-in point.
68
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_10Navigation.fm]
Masterpage:Right+
MV5SEK_00.book Page 69 Wednesday, August 31, 2005 7:58 PM
NAVIGATION (DVD DECK ONLY)
69
EN
Move Scenes
Delete Unwanted Part From Play List
1 Perform steps 1 to 3 of “Create Play List” (墌 pg. 68) before
1 Perform steps 1 to 3 of “Create Play List” (墌 pg. 68) before
continuing.
continuing.
2 Press w e to select a play list into which you wish to move a
2 Press w e to select a play list from which you wish to delete
scene, then press t.
unwanted parts, then press t.
3 Press w e to select “EDITING”, then press ENTER.
4 Press w e to select “MOVE
3 Press w e to select “EDITING”, then press ENTER.
4 Press w e to select “DELETE
DELETE SCENE
MOVE SCENE
ADD SCENE
SCENE”.
5 Press 4 to start playback. The
playback pictures appear in the
window on the screen. The
elapsed playing time starts
counting with the arrow on “IN”.
● To locate the beginning of other
titles, press 2/6.
DELETE SCENE
IN
OUT
-:--:--:--
IN
-:--:--:--
OUT
: : :
-:--:--:--
TOTAL TIME
MOVE TO
TITLE 05 CHAPTER 01
TIME -- --:--:--:--
RETURN
OK
SELECT
PREVIEW
NAVIGATION
EXIT
EXECUTE
CLEAR
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
MOVE SCENE
ADD SCENE
SCENE”, then press ENTER.
IN
5 Press 4 to start playback. The
playback pictures appear in the
window on the screen. The
elapsed playing time starts
counting with the arrow on “IN”.
● To locate the beginning of other
titles, press 2/6.
OUT
-:--:--:--
IN
-:--:--:-: : :
OUT
TOTAL TIME
TITLE 05 CHAPTER 01
TIME -- --:--:--:--
RETURN
OK
SELECT
PREVIEW
NAVIGATION
EXIT
EXECUTE
CLEAR
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
6 Find the point where you want the moved scene to begin, then
6 Find the point where you want the deletion to begin, then press
press ENTER with the arrow on “IN”. The edit-in time is fixed and
the elapsed playing time starts counting again.
ENTER with the arrow on “IN”. The edit-in time is fixed and the
elapsed playing time starts counting again.
7 Find the point where you want the moved scene to end, then
7 Find the point where you want the deletion to end, then press
press ENTER with the arrow on “OUT”. The edit-out time is fixed.
8 Press 4 to start playback.
9 Find the point where you want the moved scene to be moved,
ENTER with the arrow on “OUT”. The edit-out time is fixed.
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in and edit-out
points.
then press ENTER with the arrow on “MOVE TO”.
8 Press w e to select “PREVIEW”, then press ENTER to preview
10 Press w e to select “PREVIEW”, then press ENTER to
9 Press w e to select “EXECUTE”, then press ENTER. The
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in, edit-out and
move-to points.
preview the part approximately 5 seconds before and after the
point to which the scene has been moved.
11 Press w e to select “EXECUTE”, then press ENTER. The
selected scene is moved.
To modify the points
A Press w e to select “CLEAR”, then press ENTER.
B Repeat steps 5 – 11 as necessary.
12 Press NAVIGATION to return to the normal screen.
the scene approximately 5 seconds before and after the deleted
part.
selected scene is deleted.
To modify the points
A Press w e to select “CLEAR”, then press ENTER.
B Repeat steps 5 – 9.
10 Press NAVIGATION to return to the normal screen.
NOTE:
There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
NOTE:
There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
69
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_10Navigation.fm]
Masterpage:Left+
MV5SEK_00.book Page 70 Wednesday, August 31, 2005 7:58 PM
70 EN NAVIGATION (DVD DECK ONLY)
Play Back Play List
1 Perform steps 1 to 3 of “Create Play List” (墌 pg. 68) before
continuing.
2 Press w e to select the index
(small still pictures) of the desired
play list.
ORIGINAL
PLAY LIST
LIBRARY
0001
1
2
3
4
● You can press PR + or – to show
other pages.
[OTHERS]
● When you want the plural play
28/07/03 MON
MODIFY
DELETE
EDITING
CREATE
lists to be played back
OK
NAVIGATION
SELECT WITH [CURSORS]
continuously, press MEMO after
THEN PRESS [ENTER]
EXIT
SELECT
selecting the desired play lists.
The numbers of the playback
order appear on the index. You can select up to 30 play lists.
● When you want to correct the order, move the arrow on the desired
index and press MEMO. The number disappears and the unit renumbers the other play lists automatically.
● When you want to cancel the order, press CLEAR (8).
3 Press ENTER or 4 to start playback.
4 Press 9 to pause playback.
● To resume normal playback, press 4.
5 Press 8 to stop playback.
Delete Play List
1 Perform steps 1 to 3 of “Create Play List” (墌 pg. 68) before
continuing.
2 Press w e to select one play list you want to delete, then press
t.
3 Press w e to select “DELETE”, then press ENTER.
4 Press w e to select “YES”, then press ENTER.
● When you cancel the deletion, select “NO”, then press ENTER.
5 Press NAVIGATION to return to the normal screen.
NOTE:
Even if a play list is deleted, the titles recorded on a DVD disc and the
library information are not affected at all.
Modify Index
A Perform steps 1 to 3 of “Create Play List” (墌 pg. 68) before
continuing.
B Perform steps 3 to 8 of “Modify Index” (墌 pg. 66).
Modify Play List Name
A Perform steps 1 to 3 of “Create Play List” (墌 pg. 68) before
continuing.
B Press rt w e to select one title you want to modify, then
press t.
C Perform steps 2 to 7 of “Modify Title Name” (墌 pg. 67).
Modify Category
A Perform steps 1 to 3 of “Create Play List” (墌 pg. 68) before
continuing.
B Press rt w e to select one play list you want to modify, then
press t.
C Perform steps 2 to 6 of “Modify Category” (墌 pg. 67).
70
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_10Navigation.fm]
Masterpage:Right+
MV5SEK_00.book Page 71 Wednesday, August 31, 2005 7:58 PM
NAVIGATION (DVD DECK ONLY)
EN
71
Register Disc
Modify Library Information
1 Load a disc you want to register.
2 Press NAVIGATION. The Library Database DVD Navi screen
appears.
Title information can be registered in the unit’s memory for up to
1,300 titles. It is helpful when finding out on which disc the desired
programme is recorded.
3 Press rt w e to select “LIBRARY”, then press ENTER.
4 Press w e to select “REGISTER”, then press ENTER.
5 Press w e to select “REGISTER”, then press ENTER to confirm
the registration.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
6 Press NAVIGATION to return to the normal screen.
NOTES:
● It is not possible to register discs used for On-Disc Timer
Programming. (墌 pg. 32)
● It is not possible to register discs formatted on devices other than
JVC’s DVD recorders.
● It is not possible to register discs recorded on devices other than
JVC’s DVD recorders.
● It is not possible to register discs when “SAVE AS LIBRARY” is set to
“OFF”. (墌 pg. 79)
Delete Information
PR +/–
1 Press NAVIGATION. The Library Database DVD Navi screen
appears.
NAVIGATION
ENTER
2 Press rt w e to select “LIBRARY”, then press ENTER.
3 Press rt w e to select the appropriate sort button to sort the
information, then press ENTER.
4 Press w e to select a title you want to delete, then press t.
5 Press rt w e to select “DELETE”, then press ENTER.
6 Press w e to select “DELETE”, then press ENTER to confirm
rtwe
the deletion.
Scan For Title From Library
7 Press NAVIGATION to return to the normal screen.
1 Press NAVIGATION. The Library Database DVD Navi screen
appears.
2 Press rt w e to select “LIBRARY”, then press ENTER.
3 Press w e to select the
ORIGINAL
appropriate sort button to sort the
information, then press ENTER.
“DISC No.” : Sort by disc number
“CATEGORY” : Sort by category
“DATE” : Sort by date
“NAME” : Sort by name
DISC No.
DELETE
OK
PLAY LIST
CATEGORY
LIBRARY
DATE
NAME
REGISTER
NAVIGATION
● The sorting order can be switched SELECT
EXIT
between ascending order and
descending order by pressing the sort buttons.
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
4 Press w e to select the desired title, then press ENTER.
● You can press PR + or – to show other pages.
● Playback begins automatically after the selected title is located.
When the disc that contains the selected title is not loaded
A screen prompting you to load the designated disc appears. Place
the disc whose number is displayed on the screen after pressing
ENTER to close the prompt screen. Then perform steps 1 to 4.
NOTE:
If a disc registered in the library is recorded or modified on DVD units
from other manufacturers, it may become impossible to operate
properly.
71
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_10Navigation.fm]
Masterpage:Left+
MV5SEK_00.book Page 72 Wednesday, August 31, 2005 7:58 PM
72
EN
NAVIGATION (DVD DECK ONLY)
Playback With MP3/JPEG Navigation
Locating The Desired Group And Tracks
1 Load a disc.
2 Press NAVIGATION. The MP3/JPEG Navigation screen
appears.
This unit can play back discs that MP3 sound files and JPEG
image files taken with digital still cameras or other devices are
recorded.
The MP3/JPEG Navigation enables you to search and select the
desired files recorded on CD-R/RW or CD-ROM discs very easily.
The following screen appears as the MP3/JPEG Navigation screen
when you press NAVIGATION. You can move the arrow to select
the desired position on the screen by pressing rt w e on the
remote control.
A
B
MY BEST
MP3
JPEG
ROOT
Europe
D
EXIT
The unit starts playback from the selected item.
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
E
G
F
H
I
SONG SONG
another.mp3
1/48
01SONG
07SONG
SONG
02SONG
03SONG
04SONG
05SONG
06SONG
08SONG
09SONG
10SONG
11SONG
12SONG
SONG
SONG
1 SONG
SONG
2 SONG
OK
NAVIGATION
EXIT
Tracks” above before continuing.
Name of the inserted disc.
Sort buttons (“MP3” / “JPEG”)
Selected group number/total number of groups on the disc
Group name
Return button (“RETURN”)
Group name/Created date
File type indicator
: MP3
: JPEG
H Selected file
I Selected file number/total number of files in the group that
contains the selected file
J Title number/file name
● If you press 4 instead of ENTER in step 4, the unit starts playback
from the first file of the group.
● JPEG files are played back as a slide show at the set intervals.
(墌 pg. 58)
● If a file name includes any 2-byte character, the unit may not show
the file name correctly.
● Press rt to select “RETURN”, then press ENTER to return to the
screen that shows the group(s).
● The order of the groups and items shown in steps 4 and 5 may differ
from the order shown on your PC.
1 Perform steps 1 to 4 of “Locating The Desired Group And
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
J
A
B
C
D
E
F
G
NOTES:
Programme Playback
RETURN
SELECT
For MP3 Playback
● The tracks in the selected group appear.
● The unit stops when all items in the selected group are played back.
Rock
RETURN
SELECT
4 Press w e to select the desired group, then press ENTER.
5 Press rt w e to select the desired item, then press ENTER.
1/1
20/11/03 THU 20/11/03 THU 20/11/03 THU 20/11/03 THU
NAVIGATION
For JPEG Playback
Press w e to select “JPEG”. Only groups which contain JPEG files
appear.
● The images in the selected group appear.
MUSIC/FRANCE/POPS
20/11/03 THU
OK
Press w e to select “MP3”. Only groups which contain MP3 files
appear.
For JPEG Playback
C
Pops
3 For MP3 Playback
2 Press rt w e to select the desired item, then press MEMO in
the desired order.
● The order number appears on the left of the track name.
● Repeat this step as necessary.
● To cancel the track, press rt w e to select the track, then press
CANCEL.
● Pressing CLEAR (8) clears all the order numbers.
3 Press 4 to start playback.
● To quit the Programme Playback, press 8.
● Repeat playback can be performed if it is set as such on the onscreen bar. (墌 pg. 55)
NOTES:
● It is not possible to select tracks and images simultaneously.
● It is not possible to select tracks or images in other groups.
On completion of the playback of all the items
A Perform steps 1 to 4 of “Locating The Desired Group And
Tracks” above.
B Press CLEAR (8).
● The order numbers are reset and cleared.
C Press NAVIGATION to complete the procedure.
72
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_11TocSubsidiary.fm]
Masterpage:Right0
MV5SEK_00.book Page 73 Wednesday, August 31, 2005 7:58 PM
EN
73
Arrange your style
Remote control setting ..................................... 74
How to change the code or how to operate your TV set with this remote control.
For better sound ............................................. 77
Using Dolby Digital or DTS equipment
It can be more useful by changing your settings!
For DVD operations....................................... 78
For VHS operations ....................................... 81
Format .......................................................... 89
Before you start recording on a new disc
Finalise ......................................................... 90
To play back a disc on other DVD players
Need help?
Tips for your trouble ........................................ 91
Specifications ................................................. 95
Appendix — Language code list —...................... 96
Appendix — TV station and ID list — ................... 97
Appendix — TV station channel number guide — .. 98
What do you want to know? — Terms — ............. 99
73
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_12RemoSys.fm]
Masterpage:Left0
MV5SEK_00.book Page 74 Wednesday, August 31, 2005 7:58 PM
74
EN
REMOTE CONTROL
● Keep pressing SET UP down during step 1.
Remote Control Functions
1 Press the number button “1” for 1, “2” for 2, “3” for 3 or “4”
for 4 to change the remote control code, then press ENTER.
Remote Control 1/2/3/4 Code Switching
The remote control is capable of controlling four JVC video units
independently. Each of the units can respond to one of four codes
(1, 2, 3 or 4). The remote control is preset to send 3 code signals
because your unit is initially set to respond to 3 code signals. You
can easily modify your unit to respond to 1, 2 or 4 code signals.
● Slide the TV/DVD switch to DVD.
2 Press 1 on the unit to turn off the unit.
3 Press 4 on the unit for over 5 seconds while the unit is turned
off. The code currently set appears on the front display panel.
4 Press 8 on the remote control to change the unit’s code. The
code currently set on the remote control blinks on the front display
panel for approximately 5 seconds, and is applied to the unit.
NOTE:
Even when “POWER SAVE” is set to “ON” (墌 pg. 79), it is possible to
change the remote code.
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
1–4
ENTER
SET UP
74
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_12RemoSys.fm]
Masterpage:Right+
MV5SEK_00.book Page 75 Wednesday, August 31, 2005 7:58 PM
REMOTE CONTROL
EN
75
TV Multi-Brand Remote Control
Your remote control can operate the basic functions of your TV set.
In addition to JVC TVs, other manufacturer’s TVs can also be
controlled.
0–9
TV/VIDEO
TV +/–
● Turn off the TV using its remote control.
● Slide the TV/DVD switch to TV.
IMPORTANT:
PR +/–
Although the provided remote control unit is compatible with JVC
televisions, as well as many other models, it may not work with your TV,
or in some instances, may have limited function capability.
● Keep pressing SET UP down during step 1.
1 Enter your TV’s brand code using the number buttons, then
press ENTER.
ENTER
2 Press 1 on the unit’s remote control to turn on the TV and try
operations (墌 step 3).
● Once you have set the remote control to operate the TV, you do not
have to repeat this step until you replace your remote control’s
batteries.
● Some brands of TVs have more than one code. If the TV does not
function with one code, try entering another.
3 Press the corresponding buttons to operate the TV: 1, TV/
VIDEO, PR +/–, TV % +/–, number buttons.
● For some brands of TVs, you must press ENTER after having
pressed the number buttons.
SET UP
75
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
BRAND NAME
CODE
JVC
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SHARP
SONY
SAMSUNG
SANYO
SEARS
TOSHIBA
ZENITH
01, 03
10
02
03
04, 11
05
06
07
12
13
13
08
09
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_12RemoSys.fm]
Masterpage:Left0
MV5SEK_00.book Page 76 Wednesday, August 31, 2005 7:58 PM
76
EN
SYSTEM CONNECTIONS
Connecting To A Satellite Receiver
Connect the satellite receiver to the [L-2 IN/DECODER] connector,
then connect the [L-1 IN/OUT] connector to the TV’s connector.
NOTES:
● Set “L-2 SELECT” to “VIDEO/RGB” or “S-VIDEO/RGB”. (墌 pg. 45)
● You can use the Automatic Satellite Programme Recording function
(墌 pg. 36) with this connection. (DVD deck only)
● To record a programme via the satellite receiver, select L-2 mode by
pressing PR +/– so that “L-2” appears on the front display panel.
● For details, refer to the instruction manual of the satellite receiver.
Outdoor unit
Satellite cable
Connecting/Using A Decoder (DVD
Deck Only)
The [L-2 IN/DECODER] connector can be used as an input
connector for an external decoder (descrambler). Simply connect a
decoder and you can enjoy a variety of programming that is
available through scrambled channels.
Decoder
TV aerial cable
Aerial
TV aerial cable
TV
L-1 IN/OUT
Satellite receiver
ANTENNA IN
ANTENNA OUT
L-2 IN/
DECODER
RF cable (provided)
TV
1 Set “L-2 SELECT” to “DECODER”. (墌 pg. 45)
2 Connect your unit’s [L-2 IN/DECODER] connector to the
decoder’s 21-pin SCART connector using a 21-pin SCART cable.
IMPORTANT
When you set “L-2 SELECT” to “SAT VIDEO/RGB” (墌 pg. 45), it
is possible to view a satellite broadcast with the TV set to its AV
mode even if the unit is turned off. When the unit is in Stop mode
or recording, press TV/VIDEO on the remote control to turn off
the video indicator (
) on the unit.
● If you turn on the unit when the satellite receiver’s power is off,
nothing appears on the TV screen. In this case, turn on the satellite
receiver, or set the TV to its TV mode, or press TV/VIDEO on the
remote control to set the unit to the AV mode.
76
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_12RemoSys.fm]
MV5SEK_00.book Page 77 Wednesday, August 31, 2005 7:58 PM
Masterpage:Right+
SYSTEM CONNECTIONS
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
These instructions enable you to connect your unit to a Dolby
Digital Decoder or an amplifier with built-in DTS.
EN
77
When you can’t switch the audio channel of a bilingual
programme
When the unit is connected with a digital audio device using an
optional coaxial cable and “DIGITAL AUDIO OUT” is set to
“DOLBY DIGITAL/PCM”, it is not possible to switch the audio
channel of a bilingual programme recorded on a DVD-RAM or
DVD-RW (VR mode) disc. In this case, perform the following steps
using the remote control to switch “DIGITAL AUDIO OUT” from
“DOLBY DIGITAL/PCM” to “PCM ONLY”.
A Press SET UP to access the Main Menu screen.
B Press w e to select “DVD SET UP”, then press t.
C Press w e to select “AUDIO OUTPUT”, then press t.
D Press rt to select “DIGITAL AUDIO OUT”, then press
ENTER.
E Press rt to select “PCM ONLY”, then press ENTER.
(墌 pg. 78)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel. (墌 pg. 50)
Dolby Digital Decoder or
amplifier with built-in DTS
To DIGITAL AUDIO input
Coaxial cable
(not provided)
To [DIGITAL AUDIO
OUT (COAXIAL)]
Rear of unit
1 Connect the unit and a Dolby Digital Decoder or an amplifier
with built-in DTS using an optional coaxial cable.
NOTES:
● For Dolby Digital sound, set “DIGITAL AUDIO OUT” to “DOLBY
DIGITAL/PCM”. (墌 pg. 78)
● For DTS sound, set “DIGITAL AUDIO OUT” to “STREAM/PCM”.
(墌 pg. 78)
CAUTIONS:
● This unit has a dynamic range of more than 110 dB with regards to its
Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to the
speakers may damage them.
● Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do not
place the speakers adjacent to the TV set as this can adversely affect
the playback picture.
77
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Left0
MV5SEK_00.book Page 78 Wednesday, August 31, 2005 7:58 PM
78
EN
SUBSIDIARY SETTINGS
* The boldface settings below indicate the settings at your purchase.
Mode Set (DVD Deck)
AUDIO OUTPUT
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
8 DIGITAL AUDIO OUT — DOLBY DIGITAL / PCM / STREAM /
PCM / PCM ONLY
Set to the appropriate mode according to the type of the device
connected to [DIGITAL AUDIO OUTPUT] connector.
DOLBY DIGITAL/PCM: Select this when you connect the digital
input connector of a Dolby Digital Decoder or an amplifier with a
built-in Dolby Digital Decoder.
STREAM/PCM: Select this when you connect the digital input
connector of an amplifier with a built-in DTS, Dolby Digital, or
MPEG multichannel decoder.
PCM ONLY: Select this when you connect the linear PCM digital
input of other audio equipment (amplifier, MD or DAT deck, etc.).
NOTE:
DVD
If you watch or play back a title which contains multiple audio
languages, select “PCM ONLY” in advance and choose main or sub
audio with AUDIO.
8 ANALOG AUDIO OUT — STEREO / DOLBY SURROUND
ENTER
Select the appropriate setting to accommodate the unit to the
connected A/V equipment. This function takes effect when a
DVD VIDEO disc is played back.
STEREO: Select this when listening to conventional two-channel
stereo audio with the unit’s [AUDIO OUTPUT] connectors
connected to a stereo amplifier/receiver or TV set, or in case you
want to record the audio from a DVD VIDEO disc to a Mini Disc,
etc.
DOLBY SURROUND: Select this when listening to multichannel
surround audio with the unit’s [AUDIO OUTPUT] connectors
connected to an amplifier/receiver with a built-in surround
decoder or a surround decoder.
rtwe
SET UP
8 D. RANGE CONTROL — NORMAL / WIDE RANGE / TV
MODE
Various modes of this unit are categorised into menus nested in 2
levels shown in the following table. To change the settings of these
modes, find the desired mode in the menu (for details on each
menu, see pages 78 through 80), then follow the procedure below.
DVD SET UP
LANGUAGE SET (墌 pg. 20)
AUDIO OUTPUT (墌 pg. 78)
UTILITY (墌 pg. 89, 90)
FUNCTION SET UP
VIDEO IN/OUT (墌 pg. 21, 44)
RECORDING SET (墌 pg. 79)
DISPLAY SET (墌 pg. 79)
OTHERS (墌 pg. 80)
INITIAL SET UP
AUTO CH SET (墌 pg. 84)
MANUAL CH SET (墌 pg. 85)
GUIDE PR (墌 pg. 83)
CLOCK SET (墌 pg. 88)
● The procedure below shows how to set the desired option of the
“AUDIO REC” mode as an example.
1 Press DVD so that the DVD lamp lights up on the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “FUNCTION SET UP”, then press t.
4 Press w e to select
DVD SET UP
“RECORDING SET”, then press t.
5 Press rt to select “AUDIO
REC”, then press ENTER.
6 Press rt to select the desired
FUNCTION SET UP
VIDEO IN/OUT RECORDING SET
SAVE AS LIBRARY
XP MODE REC AUDIO
AUDIO REC
DIRECT REC
option, then press ENTER.
7 Press SET UP to complete the
SET UP
EXIT
setting.
78Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
OK
SELECT
INITIAL SET UP
DISPLAY SET
OTHERS
ON
DOLBY DIGITAL
NICAM1/MAIN
NICAM1/MAIN
NICAM2/SUB
MONO
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
The dynamic range (the difference between the loudest sound and
the quietest one) can be compressed during playback of a
programme encoded in Dolby Digital format.
This function takes effect when a DVD VIDEO disc recorded in
Dolby Digital format is played back at low or middle volume.
NORMAL: Normally select this setting to activate this function.
WIDE RANGE: Select this to deactivate this function when you
enjoy wide dynamic range programme.
TV MODE: Select this when you hear the sound through the TV’s
speaker(s).
NOTES:
● This function has no effect on programmes other than that recorded
in Dolby Digital format.
● The effect of “NORMAL” and “WIDE RANGE” may not be different
depending on discs.
8 OUTPUT LEVEL — STANDARD / LOW
You can lower the output level of analog audio to accommodate
the unit to the connected A/V equipment.
STANDARD: Normally select this setting.
LOW: The output level of analog audio is lowered.
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Right+
MV5SEK_00.book Page 79 Wednesday, August 31, 2005 7:58 PM
SUBSIDIARY SETTINGS
EN
79
RECORDING SET
DISPLAY SET
8 SAVE AS LIBRARY — OFF / ON
8 SUPERIMPOSE — OFF / AUTO
When this function is set to “ON”, the recording information is
automatically stored in the library. For details, refer to “Modify
Library Information” (墌 pg. 71).
When this function is set to “AUTO”, various operational indicators
appear on the TV screen.
OFF: To turn off superimposed indications.
AUTO: To superimpose operational indications for approximately
five seconds just after the corresponding operation.
8 XP MODE REC AUDIO — DOLBY DIGITAL / LINEAR PCM
You can select the audio format when you record a title in XP
mode. When this function is set to “LINEAR PCM”, you can obtain
a high-quality audio sound.
DOLBY DIGITAL: To record in Dolby Digital format.
LINEAR PCM: To record in Linear PCM format.
8 AUDIO REC — NICAM 1/MAIN / NICAM 2/SUB / MONO
You can select the desired NICAM audio channel to be recorded
on a DVD-R/RW (Video mode) disc.
NICAM 1/MAIN: To record the main language of NICAM audio.
NICAM 2/SUB: To record the sub language of NICAM audio.
MONO: To record the standard (monaural) sound of NICAM audio.
NOTE:
This function works only for the NICAM bilingual programme.
8 DIRECT REC — OFF / ON
When this function is set to “ON”, you can easily start recording the
programme that you are watching on your TV. Press and hold 7
and press 4 on the remote control, or press 7 on the unit.
NOTES:
● When you use the Direct Rec function, be sure to use a TV offering
T-V LINK, etc. and connect a fully-wired 21-pin SCART cable
between the unit and the TV. (墌 pg. 15)
● If “DIRECT REC” is set to “OFF”, the 7 button functions as described
in “Basic Recording (DVD)” (墌 pg. 26) or “Basic Recording (VHS)”
(墌 pg. 28).
● During Direct Rec, “– –” appears on the front display panel.
● If a programme is recorded with the Direct Rec, the station name will
not be registered in the library. “– – – –” will be displayed for the
station name.
● Even if there is no power supply for more than 60 minutes, the unit
keeps the setting.
NOTES:
● Even when “SUPERIMPOSE” is set to “OFF”, you can display the
various operational indicators by pressing ON SCREEN. To clear the
operational indicators, press ON SCREEN again.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting.
● When you select “AUTO”, during playback, the operation mode
indicators may be disturbed depending on the type of disc being
used.
8 GREY/BLUE BACK — OFF / ON
When this function is set to “ON”, the TV screen becomes all grey
(DVD deck)/blue (VHS deck) when receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals, set
this function to “OFF”.
8 DIMMER — BRIGHT / DIMMED1 / DIMMED2 / OFF
You can change the brightness of the front display panel.
BRIGHT: To turn on the light on the front display panel. (Blue lamp
on the front display panel is turned on.)
DIMMED1/DIMMED2: To change the brightness level. (Blue lamp
on the front display panel is turned off.)
OFF: To turn off the light on the front display panel. (Blue lamp on
the front display panel is turned off.)
8 POWER SAVE — OFF / ON
When this function is set to “ON”, you can reduce the power
consumption while the unit is turned off.
● During Power Save mode —
— the front display panel will be turned off.
— the Just Clock function (墌 pg. 88) does not work.
● Power Save does not work when —
— the unit is in the Timer mode.
— the unit’s power is turned off after timer-recording or Instant Timer
Recording.
— “L-2 SELECT” is set to “DECODER” or “SAT VIDEO/RGB”. (墌 pg. 45)
● It takes some time for the unit to complete initialisation after you turn
on the unit power, with “HELLO” blinking on the front display panel.
79Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Left+
MV5SEK_00.book Page 80 Wednesday, August 31, 2005 7:58 PM
80 EN SUBSIDIARY SETTINGS
OTHERS
8 RESUME — OFF / ON / DISC RESUME
When this function is set to “ON” or “DISC RESUME”, you can use
the resume function. (墌 pg. 48)
OFF: You cannot use the resume function.
ON: You can start playback from the resume point of the placed
disc.
DISC RESUME: The unit retains a memory of the resume points of
the last 30 discs played back, even though they have been
ejected.
NOTE:
VHS
DVD
“DISC RESUME” setting works on DVD VIDEO, VCD and already
finalised DVD-R/DVD-RW (video mode) discs. For other types of discs,
the function under “ON” setting will be applied even if “RESUME” is set
to “DISC RESUME”.
8 AUTO POWER OFF — OFF / 3H
When this function is set to “3H”, the unit is turned off automatically
if no operation is done with 3 hours.
Scan Mode Set
If you connect the unit and TV with Component Video Connection
(墌 pg. 15), you can select the scan mode from two modes:
Interlaced scan mode which is used in the conventional TV
system, and Progressive scan mode which enables reproduction
of higher-quality images.
8 Interlaced scan
In the conventional video system, a picture is shown on the display
monitor in two halves. The Interlaced scan system places lines of
the second half of the picture in-between lines of the first half of the
picture.
8 Progressive scan
Progressive scan displays all the horizontal lines of a picture at
one time, as a single frame. This system can convert the interlaced
video from DVD into progressive format for connection to a
progressive display. It dramatically increases the vertical
resolution.
ATTENTION:
● Your TV needs to be compatible with Progressive.
● Make sure that there is no disc in the unit.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
PROGRESSIVE
SCAN
1 Press DVD so that the DVD lamp lights up on the unit.
2 Press PROGRESSIVE SCAN for 3 or more seconds.
● Video output indicator ( ) lights on the front display panel if
Progressive scan mode has been established. (墌 pg. 14)
● Each press of PROGRESSIVE SCAN for 3 or more seconds
switches the scan mode.
NOTES:
● When the progressive mode is set, be sure to set “L-1 OUTPUT” to
“COMPONENT”. (墌 pg. 44) Progressive scan is output only from
[COMPONENT VIDEO OUT] connector.
● Interlaced scan mode is the setting at your purchase.
● Interlaced scan mode might be suitable depending on video material.
● Scan mode cannot be set while menu screen is displayed.
● When the Progressive scan mode is engaged, no video signal is
output from [L-1 IN/OUT] connector.
Watch the images on VHS deck in the Progressive scan
mode via component video
1 Set the Progressive-compatible TV to the component input
mode.
2 Press DVD so that the DVD lamp lights up on the unit.
3 Press PROGRESSIVE SCAN for 3 or more seconds.
● The video output indicator
lights up on the front display panel.
4 Press VHS so that the VHS lamp lights up on the unit, then
press PROGRESSIVE SCAN.
● “]” lights up on the unit.
NOTES:
● Be sure to engage the DVD deck in stop mode.
● During still picture in VHS Progressive Scan mode, the images
may jitter, but this is not a malfunction.
80Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Right+
MV5SEK_00.book Page 81 Wednesday, August 31, 2005 7:58 PM
SUBSIDIARY SETTINGS
EN
81
* The boldface settings below indicate the settings at your purchase.
Mode Set (VHS Deck)
8 VHS]DVD DUBBING — 1 PROG / ENTIRE
Set to the appropriate mode when you perform the dubbing from
VHS tape to DVD disc. For details, refer to pages 37 – 38.
1 PROG: Dubbing stops when the unit decodes the index code
(VISS signal).
ENTIRE: Dubbing stops when the end of the tape reached.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
8 B.E.S.T. — ON / OFF
You can set the B.E.S.T. (Biconditional Equalised Signal Tracking)
system to “ON” or “OFF”.
NOTES:
VHS
ENTER
rtwe
● When watching a tape recorded with “B.E.S.T.” set to “ON”, it is
recommended that you leave B.E.S.T. on during playback as well.
● When watching a rental tape or one recorded on another video
recorder, or when using this unit as the player for editing, set
B.E.S.T. to your preference.
● The B.E.S.T. system works for both SP and LP modes only after a
tape has been inserted and the Record mode is first initiated. It does
not work during recording.
● The B.E.S.T. system does not work while Automatic Satellite
Programme Recording is in progress. (墌 pg. 36)
● In the case of timer recordings, the B.E.S.T. system works before
recording is initiated.
● Once the cassette is ejected, the B.E.S.T. data is cancelled. The next
time the cassette is used for recording, B.E.S.T. is re-performed.
● Pressing the unit’s 7 button while “BEST” is displayed does not start
Instant Timer Recording. (墌 pg. 61)
8 PICTURE CONTROL — AUTO (NORM) / EDIT / SOFT
SET UP
Various modes of this unit are categorised into menus nested in 2
levels shown in the following table. To change the settings of these
modes, find the desired mode in the menu (for details on each
menu, see pages 81 through 82), then follow the procedure below.
VHS SET UP
(墌 pg. 81 – 82)
FUNCTION SET UP*
VIDEO IN/OUT (墌 pg. 21, 44)
RECORDING SET (墌 pg. 79)
DISPLAY SET (墌 pg. 79)
OTHERS (墌 pg. 80)
* Common settings with DVD
deck
INITIAL SET UP*
* Common settings with DVD
deck
AUTO CH SET (墌 pg. 84)
MANUAL CH SET (墌 pg. 85)
GUIDE PR (墌 pg. 83)
CLOCK SET (墌 pg. 88)
● The procedure below shows how to set the desired option of the
“B.E.S.T.” mode as an example.
1 Press VHS so that the VHS lamp lights up on the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “VHS SET UP”, then press t.
4 Press rt to select “B.E.S.T.”,
VHS SET UP
FUNCTION SET UP
INITIAL SET UP
then press ENTER.
5 Press rt to select the desired
option, then press ENTER.
6 Press SET UP to complete the
VHS ] DVD DUBBING
B.E.S.T
ENTIRE
PICTURE CONTROL
ON
OFF
AUTOON
AUDIO SP ] LP TIMER
OFF
setting.
SET UP
EXIT
81Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
OK
SELECT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
This feature helps you to adjust the playback picture quality
according to your preference. Normally select “AUTO (NORM)”.
AUTO (NORM): Picture quality is adjusted automatically.
EDIT: Minimises picture degradation during editing (recording and
playback).
SOFT: Reduces image coarseness when viewing overplayed tapes
containing a lot of noise.
NOTES:
● When you select “EDIT” or “SOFT”, the selected mode will not
change until you select another mode.
● When you select “EDIT” to dub tapes, be sure to select “AUTO
(NORM)” after you finish dubbing the tapes.
● When “B.E.S.T.” is “OFF”, “PICTURE CONTROL” switches
automatically from “AUTO” to “NORM”.
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Left+
MV5SEK_00.book Page 82 Wednesday, August 31, 2005 7:58 PM
82
EN
SUBSIDIARY SETTINGS
8 AUTO SP]LP TIMER — ON / OFF
When this function is set to “ON”, the unit automatically switches to
LP mode to allow complete recording if there is not enough tape to
record the entire programme while timer-recording in SP mode.
For Example:
Recording a programme of 140 minutes in length onto a 120-minute tape.
Approximately 100 minutes
SP mode
Tray Lock (DVD Deck Only)
You can lock the disc tray to prohibit the unwanted disc ejection by
children.
● Turn off the unit.
Approximately 40 minutes
LP mode
Total 140 minutes
Make sure you set this function to “ON”, before the timer-recording starts.
NOTES:
● If you have programmed the unit to timer-record 2 or more
programmes, the second programme and those thereafter may not fit
on the tape if you set “AUTO SP]LP TIMER” to “ON”. In this case,
make sure the mode is not engaged, then set the tape speed
manually during timer programming.
● In order to ensure that the recording fits on the tape, this feature may
leave a slight non-recorded section at the end of the tape.
● There may be some noise and sound disturbance at the point on the
tape where the unit switches from SP to LP mode.
● The “AUTO SP]LP TIMER” feature is not available during ITR
(Instant Timer Recording), and the feature will not work properly on
the following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.
82Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
VHS
STANDBY/ON
REC
DVD
PR
VHS/DVD
S-VIDEO
VIDEO
AUDIO
VHS
DUBBING
DVD
DV IN
To lock tray
While the unit is turned off, press and hold 8, then press x
(OPEN/CLOSE) on the unit. “LOCK” appears on the front display
panel and the disc tray is locked.
To unlock tray
While the unit is turned off, press and hold 8, then press x
(OPEN/CLOSE) on the unit. “UNLOCK” appears on the front
display panel.
Filename [MV5SEK_13Subsidiary.fm]
MV5SEK_00.book Page 83 Wednesday, August 31, 2005 7:58 PM
Masterpage:Right+
SUBSIDIARY SETTINGS
EN
83
Guide Program Number Set
VIDEO Plus+ System Setup
IMPORTANT:
Normally, Auto Set Up (墌 pg. 17), Preset Download (墌 pg. 18) or
Auto Channel Set (墌 pg. 84) sets the Guide Program numbers
automatically. You need to set the Guide Program numbers manually
only in the following cases.
● When timer-programming with the VIDEO Plus+ system, the
channel position, where the station you wish to record is received
on your unit, is not selected,
OR
when you add a channel after Auto Set Up, Preset Download or Auto
Channel Set has taken place,
—Set the Guide Program number for that station manually.
● When you wish to timer-record a satellite programme with the
SHOWVIEW system,
—Set the Guide Program numbers for all satellite broadcasts received
on your satellite receiver.
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “INITIAL SET UP”, then press t.
3 Press w e to select “GUIDE
DVD SET UP
PR”, then press t.
4 Press rt to select “GUIDE
PROGRAMME”, then press
ENTER.
5 Press rt to select the Guide
Program number for the desired
station as shown in the TV
listings. Then press ENTER.
FUNCTION SET UP
AUTO CH SET MANUAL CH SET
GUIDE PROGRAMME
TV PROGRAMME
SET UP
EXIT
OK
SELECT
INITIAL SET UP
GUIDE PR
CLOCK SET
1
F-1
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
● To change the Guide Program number in 10 increments, press and
hold rt.
6 Press rt to select “TV PROGRAMME”, then press ENTER.
7 Press rt to select the number of the unit’s channel position on
which the Guide Program number’s broadcast is received by the
unit or the satellite receiver. Then press ENTER.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
● If the satellite broadcast is received on your unit’s auxiliary channel
“L-2”, select “L-2” for the channel position.
● Repeat steps 4 and 7 as necessary.
8 Press SET UP to complete the setting.
Guide Program Number
“Guide Program (GUIDE PROGRAMME) number” refers to the
assigned TV station numbers, according to broadcast area, for the
VIDEO Plus+ timer recording. The Guide Program numbers can be
found in most TV listings.
VHS
ENTER
SET UP
83Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Left+
MV5SEK_00.book Page 84 Wednesday, August 31, 2005 7:58 PM
84
EN
SUBSIDIARY SETTINGS
Auto Channel Set
Tuner Set
Your unit needs to memorise all necessary stations in channel
positions in order to record TV programmes. Auto Channel Set
automatically assigns all receivable stations in your area to call
them up by using the PR +/– buttons without going through any
vacant channels.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “INITIAL SET UP”, then press t.
3 Press w e to select “AUTO CH SET”, then press ENTER.
● When you have connected the unit to a TV offering T-V Link via a
fully-wired 21-pin SCART cable (墌 pg. 15), the unit automatically
performs the Preset Download and the T-V LINK screen will appear.
(墌 pg. 18)
● The Auto Set screen appears, and remains on screen while the unit
searches for receivable stations.
Wait until the TV screen as shown in step 4 appears.
4 View the Confirmation screen.
“SCAN COMPLETED” is displayed on the TV screen. Press “OK”.
5 Press SET UP to complete the setting.
● When Auto Channel Set is completed, “PLEASE WAIT” will be
displayed for about 90 seconds, since channel data is exchanged
between the DVD deck and the VHS deck. No operations will be
done during this time.
● Using the Confirmation screen, you can skip or add channel
positions, enter station names and perform other operations. Refer to
pages 85 – 87 for the procedures.
● Depending on reception conditions, the stations may not be stored in
order, and the station names may not be stored correctly.
VHS
IMPORTANT:
● In certain reception conditions, station names may not be stored
correctly, and Auto Guide Program Number Set may not work
properly. When the Guide Program numbers are not set properly,
the programme that you do not intended to record will be timerrecorded by the VIDEO Plus+ system of the unit. When
programming the timer using the VIDEO Plus+ system, be sure to
check the desired channel is selected correctly. (墌 pg. 29)
● Your unit memorises all receivable stations even if reception of
some of them is poor. You can delete those stations with an
unacceptable picture from the list. (墌 pg. 86, “Delete A Channel”)
ENTER
NOTES:
SET UP
IMPORTANT:
Perform the following steps only if —
— Auto Channel Set has not been set correctly by Auto Set Up
or by Preset Download. (墌 pg. 17, 18)
— you have moved to a different area or if a new station starts
broadcasting in your area.
84Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
● Fine tuning is performed automatically during Auto Channel Set. If
you want to perform tuning manually, refer to “Fine-Tuning Channels
Already Stored” (墌 pg. 87).
● If you perform Auto Channel Set when the aerial cable is not
connected properly, “SCAN COMPLETED –NO SIGNAL–” appears
on the TV screen in step 4. In such a case, make sure of the aerial
connection and press ENTER; Auto Channel Set will start again.
Filename [MV5SEK_13Subsidiary.fm]
MV5SEK_00.book Page 85 Wednesday, August 31, 2005 7:58 PM
Masterpage:Right+
SUBSIDIARY SETTINGS
Manual Channel Set
Store channels that were not stored during Auto Set Up
(墌 pg. 17), Preset Download (墌 pg. 18) or Auto Channel Set
(墌 pg. 84).
85
Confirmation screen appears.
4 Press rt w e to select a
blank position in which you want
to store a channel, then press
ENTER twice. The Manual
Channel Set screen appears.
5 Press rt to select “BAND”,
then press ENTER.
VHS
EN
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “INITIAL SET UP”, then press t.
3 Press w e to select “MANUAL CH SET”, then press t. The
(Example) To store in position 12.
DVD SET UP
FUNCTION SET UP
INITIAL SET UP
INITIAL SET UP / MANUAL CH SET
PR
CH
ID
PR
CH
ID
01
26
BBC1
08
---02
33
BBC2
09
---10
---03
23
ITV
11
---04
30
CH4
12
---05
37
CH5
---13
---06
07
---14
---OK
SET UP
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
RETURN
The programme currently received
on the selected channel position
appears behind the confirmation
screen.
6 Press rt to change the band
between CH (regular) and CC
(cable), then press ENTER.
ENTER
7 Press rt to select “CH”, then
press ENTER.
8 Press rt to input the channel
number you want to store.
SET UP
DVD SET UP
FUNCTION SET UP
INITIAL SET UP
INITIAL SET UP / MANUAL CH SET
BAND
CH CH
01 CC
CH
ID
E-SP
DECODER
OFF
FINE
SET UP
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
RETURN
● To enter the registered station
name (墌 pg. 97), press rt to
select “ID”, then press ENTER. Press rt.
● For fine tuning adjustment, press rt to select “FINE”, then press
ENTER. Press rt to perform fine-tuning.
● When “L-2 SELECT” is set to “VIDEO/RGB”, “S-VIDEO/RGB” or
“SAT VIDEO/RGB”, the “DECODER” setting cannot be changed.
(墌 pg. 45)
9 Press ENTER to enter new channel information. The
Confirmation screen appears.
● Repeat steps 4 – 9 as necessary.
10 Press SET UP to close the Confirmation screen.
● When Auto Channel Set is completed, “PLEASE WAIT” will be
displayed for about 90 seconds, since channel data is exchanged
between the DVD deck and the VHS deck. No operations will be done
during this time.
● To change positions, see “Change Station Channel Position”
(墌 pg. 86).
● If you wish to set station names other than the ones registered in your
unit, see “Set Stations (B)” (墌 pg. 87).
ATTENTION:
Guide Program numbers are not set when channels are stored
manually. (墌 pg. 83, “VIDEO Plus+ System Setup”)
85Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Left+
MV5SEK_00.book Page 86 Wednesday, August 31, 2005 7:58 PM
86
EN
SUBSIDIARY SETTINGS
Delete A Channel
1 Perform steps 1 – 3 of “Manual Channel Set” (墌 pg. 85) to
access the Confirmation screen before continuing.
2 Press rt w e to select the item you want to delete.
3 Press CANCEL to delete a channel. The item next to the
cancelled one moves up one line.
● Repeat steps 2 and 3 as necessary.
4 Press SET UP to close the Confirmation screen.
Change Station Channel Position
CANCEL
1 Perform steps 1 – 3 of “Manual Channel Set” (墌 pg. 85) to
access the Confirmation screen before continuing.
2 Press rt w e to select the item you want to move, then press
ENTER
ENTER.
3 Press rt w e to select the new channel position, then press
ENTER.
Example: If you moved the station in position 4 to position 2, the
stations originally in positions 2 and 3 each move down
one space.
DVD SET UP
FUNCTION SET UP
INITIAL SET UP / MANUAL CH SET
PR
CH
ID
PR
SET UP
01
26
02
23
03
30
04
33
05
37
06
07
SET UP
BBC1
ITV
CH4
BBC2
CH5
------OK
RETURN
SELECT
08
09
10
11
12
13
14
INITIAL SET UP
CH
DVD SET UP
ID
----------------------
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
FUNCTION SET UP
INITIAL SET UP / MANUAL CH SET
PR
CH
ID
PR
01
26
02
23
03
30
04
33
05
37
06
07
SET UP
BBC1
ITV
CH4
BBC2
CH5
------OK
RETURN
SELECT
INITIAL SET UP
CH
08
09
10
11
12
13
14
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
● Repeat steps 2 and 3 as necessary.
4 Press SET UP twice to close the Confirmation screen.
86Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
ID
----------------------
Filename [MV5SEK_13Subsidiary.fm]
MV5SEK_00.book Page 87 Wednesday, August 31, 2005 7:58 PM
Masterpage:Right+
SUBSIDIARY SETTINGS
EN
Set Stations (A)
Fine-Tuning Channels Already Stored
Set station names that are registered in your unit.
1 Perform steps 1 – 3 of “Manual Channel Set” (墌 pg. 85) to
1 Perform steps 1 – 3 of “Manual Channel Set” (墌 pg. 85) to
access the Confirmation screen before continuing.
2 Press rt w e to select the item you want.
3 Press ENTER twice to access the Manual Channel Set screen.
4 Press rt to select “ID”, then press ENTER.
5 Press rt until the new station’s name (ID) you want to store
appears, then press ENTER. Registered station names (墌 pg. 97)
appear as you press rt.
6 Press w e to select “OK”, then press ENTER.
● Repeat steps 2 – 6 as necessary.
7 Press SET UP twice to close the Confirmation screen.
Set Stations (B)
Set station names other than the ones registered in your unit.
1 Perform steps 1 – 3 of “Manual Channel Set” (墌 pg. 85) to
access the Confirmation screen and then perform steps 2 and 3 of
“Set Stations (A)” above before continuing.
2 Press rt to select “ID”, then press ENTER.
3 Press ENTER twice.
4 Press w e to locate the character insertion point.
5 Press rt to cycle through the characters (A–Z, 0–9, –, f, +, I
(space)) and stop when the desired character is indicated, then
press e to enter.
● Enter the remaining characters the same way (maximum of 4).
6 After entering all characters, press w e to select “OK”, then
press ENTER.
7 Press SET UP twice to close the Confirmation screen.
NOTE:
The characters available for the station name (ID) are A–Z, 0–9, –,
f, +, I (space) (maximum of 4).
87Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
87
access the Confirmation screen before continuing.
2 Press rt w e to select the channel you want to fine-tune, then
press ENTER.
3 Press ENTER twice.
4 Press ENTER to access the Manual Channel Set screen. The
Manual Channel Set screen appears.
5 Press rt to select “FINE”.
6 Press w e until the picture appears in its best quality.
● Repeat steps 2 – 6 as necessary.
7 Press SET UP three times to close the Confirmation screen.
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Left+
MV5SEK_00.book Page 88 Wednesday, August 31, 2005 7:58 PM
88
EN
SUBSIDIARY SETTINGS
1 Press w e to select “INITIAL SET UP”, then press t.
2 Press w e to select “CLOCK
Clock Set
DVD SET UP
SET”, then press t.
IMPORTANT:
If you performed Auto Set Up (墌 pg. 17) or Preset Download
(墌 pg. 18), without ever having set the clock previously, the
unit’s built-in clock is also set automatically.
Perform the following steps only if —
— Auto Clock Set has not been performed correctly by Auto Set
Up or Preset Download.
OR
— you want to change Just Clock setting. (墌 “Just Clock” in the
right column)
FUNCTION SET UP
AUTO CH SET MANUAL CH SET
INITIAL SET UP
GUIDE PR
CLOCK SET
3 Press rt to select “YEAR”,
YEAR
2005
then press ENTER. Press rt to
set the year, then press ENTER.
DATE
05/07 (SAT)
TIME
18:56
JUST CLOCK
OFF
● Repeat the same procedure to set
TV PROGRAMME
18
the date and time. When you set
OK
SET UP
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
the time, press and hold rt to
SELECT
EXIT
change the time by 30 minutes.
● When you set the date, press and hold rt to change the date by 15
days.
4 Press rt to select “JUST CLOCK”, then press ENTER. Press
rt to set to the desired mode, then press ENTER.
● The default setting is “OFF”.
● For the Just clock function, refer to “Just Clock” below.
● If you set to “OFF”, you can disregard the next step as you won’t be
able to receive regular clock adjustments.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
5 Press rt to select “TV PROGRAMME”, then press ENTER.
Press rt to set the channel position to the number representing
the station transmitting clock setting data, then press ENTER.
● The unit is preset to receive clock setting and adjustment data from
channel position 1.
VHS
DVD
6 Press SET UP to start the clock operation.
NOTES:
● Just Clock (when set to “ON”) adjusts the unit’s built-in clock every
hour, except for 23:00, 0:00, 1:00 and 2:00.
● Just Clock is not effective when:
— the unit’s power is on.
— the unit is in the Timer mode.
— a difference of more than 3 minutes exists between the built-in
clock’s time and the actual time.
— the unit is in the Automatic Satellite Programme Recording
mode. (墌 pg. 36) (DVD deck only)
— the unit is in the Power Save mode. (墌 pg. 79)
— “L-2 SELECT” is set to “SAT VIDEO/RGB”. (墌 pg. 45)
ENTER
● If Just Clock is set to “ON”, the unit’s clock is automatically adjusted
at the start/end of Summer Time.
● Just Clock may not function properly depending on the reception
condition.
SET UP
Just Clock
The Just Clock function provides accurate time keeping through
automatic adjustments at regular intervals, by reading data from a
PDC signal.
The Just Clock option can be set to “ON” or “OFF” at the Clock Set
screen (the default setting is “OFF”).
IMPORTANT:
If you turn off Just Clock, the accuracy of your unit’s built-in clock may
be reduced, which could adversely effect timer recording. We
recommend you to keep Just Clock on. In cases where the clock setting
data from a PDC signal is incorrect, however, you are advised to keep
Just Clock set to “OFF”.
88Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Right+
MV5SEK_00.book Page 89 Wednesday, August 31, 2005 7:58 PM
SUBSIDIARY SETTINGS
Format A Disc (DVD Deck Only)
Some DVD-RAM/RW discs are unformatted.
Format the disc when you use an unformatted disc or you want to
delete all recordings and data on the disc.
ATTENTION:
● When a disc is formatted, all recordings and data are erased. It is
impossible to restore them.
● Never turn off the unit or disconnect the AC power cord while
“NOW FORMATTING...” is displayed on the TV screen.
●
●
●
●
EN
89
Format A DVD-RAM Disc
1 Press DVD so that the DVD lamp lights up on the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “DVD SET UP”, then press t.
4 Press w e to select “UTILITY”,
DVD SET UP
then press t.
5 Press rt w e to select
“FORMAT”, then press ENTER.
Press w e to select “YES”, then
press ENTER.
6 Press w e to select “OK”, then
press ENTER.
FUNCTION SET UP
INITIAL SET UP
AUDIO OUTPUT
LANGUAGE SET
UTILITY
FORMAT
FINALISE
CANCEL DISC FINALISATION
SET UP
EXIT
OK
SELECT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
Format A DVD-RW Disc
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Load a DVD-RAM/RW disc to format.
1 Perform steps 1 to 4 of “Format A DVD-RAM Disc” as above
before continuing.
2 Press rt w e to select “FORMAT”, then press ENTER. Press
DVD
w e to choose “VR MODE” or “VIDEO MODE”, then press ENTER
when “DISC WILL BE FORMATTED” appears on the TV screen.
“VR MODE”: To be chosen when you want to record, erase, or edit
data on the disc repeatedly.
“VIDEO MODE”: To be chosen when you want to erase all the data
on the disc once played back to record new data, or play back the
disc on other DVD players.
3 Press w e to select “YES”, then press ENTER.
NOTES:
● It is impossible to format Version 1.0 DVD-RW discs in Video mode.
● It is impossible to format DVD-R discs.
● All the titles on a disc will be deleted once the disc is formatted even if
they are protected titles. (墌 pg. 67)
ENTER
rtwe
SET UP
89Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Left+
MV5SEK_00.book Page 90 Wednesday, August 31, 2005 7:58 PM
90
EN
SUBSIDIARY SETTINGS
Finalise A Disc (DVD Deck Only)
Finalising DVD-R/RW discs recorded on this unit makes it possible
for the discs to be played back on other DVD players. DVD-RW
discs are finalised in the mode that the discs were formatted,
enabling playback on compatible DVD players.
Title names input in the Library Database DVD Navi are registered
as title names in the DVD menu. (墌 pg. 67)
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
Load a DVD-R/RW disc to finalise.
DVD
Before finalising
●
●
●
●
●
It is possible to record on a blank space.
It is possible to enter title names. (墌 pg. 67)
It is possible to delete titles. (墌 pg. 67)
It is impossible to overwrite recorded areas of DVD-R discs.
Available recording capacity does not increase even if a recorded
title is deleted from a DVD-R disc.
● It is impossible to record or edit DVD-R/RW discs recorded on other
devices even if they have not been finalised.
After finalising (For DVD-R/RW (Video mode) discs)
● Video and audio that have been recorded by then are recorded in
conformity to the DVD Video standard, enabling you to play back the
discs as DVD VIDEO discs.
● Although DVD-R/RW discs finalised on this unit become playable on
DVD players compatible with DVD-R/RW discs, some discs still may
not play, for which JVC cannot take responsibility.
● Marked points marked before finalising will be deleted, and titles will
be divided automatically into “chapters” approximately every 5
minutes. (墌 pg. 49)
● Depending on the DVD players and DVD-R/RW discs used, and on
the conditions of recording, it may not be possible to play back the
discs. In this case, play back the discs on this unit.
● Additional recordings become impossible.
Finalise A DVD-R/RW Disc
1 Perform steps 1 to 4 of “Format A DVD-RAM Disc” (墌 pg. 89)
before continuing.
2 Press rt w e to select “FINALISE”, then press ENTER.
● For DVD-R/RW (Video mode) discs, the background selection screen
will appear. Press rt w e to select the desired background from a
selection of 18 backgrounds.
ENTER
3 Press w e to select “OK”, then press ENTER.
4 Press w e to select “OK”, then press ENTER.
5 Press SET UP to return to the normal screen.
rtwe
● Menu screen is cleared.
● Once a DVD-R/RW (Video mode) disc has been finalised, the
displays for original and play list do not appear. Only display for
library appears.
● Once a DVD-RW (VR mode) disc has been finalised, it can be played
on DVD players compatible with VR mode.
Cancel The Finalisation Of A DVD-RW Disc
1 Load a DVD-RW disc to cancel the disc finalisation, and perform
steps 1 to 4 of “Format A DVD-RAM Disc” (墌 pg. 89) before
continuing.
SET UP
2 Press rt w e to select “CANCEL FINALISATION”, then press
ENTER.
3 Press w e to select “EXECUTE”, then press ENTER.
4 Press SET UP to return to the normal screen.
● When the disc finalisation is cancelled, the mode in which the disc
was formatted is restored, making the disc recordable. (墌 pg. 7, 89)
90Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_13Subsidiary.fm]
MV5SEK_00.book Page 91 Wednesday, August 31, 2005 7:58 PM
Masterpage:Right0
TROUBLESHOOTING
Before requesting service for a problem, use this chart and see if
you can solve the trouble yourself. Small problems are often easily
solved, and this can save you the trouble of sending your unit off
for repair.
Initialising (DVD Deck Only)
Malfunction occurs on the unit.
]Press 1 to turn off the unit, press and hold 1, then press 8
for two seconds or more.
General
No power is supplied to the unit.
● The AC power plug is disconnected from the AC outlet.
]Connect the AC power plug to the AC outlet securely. (墌 pg. 15)
The disc tray cannot be opened.
]Open the disc tray by following the steps below.
1. Press 8 and 1 on the unit simultaneously.
2. Press and hold x (OPEN/CLOSE) on the unit for
approximately 30 seconds until the tray is opened.
3. Remove the disc, then press x (OPEN/CLOSE). The unit
shuts off.
The remote control does not work properly.
]Remove the batteries, wait for 5 minutes or more, then load the
batteries again.
● The setting of the remote control code is inappropriate.
]Set the same remote control code (1, 2, 3, or 4) on both the unit
and the remote control. (墌 pg. 74)
● The batteries are discharged.
]Replace the dead batteries with new ones.
Dubbing from the external equipment is not possible.
● The source (another video recorder, camcorder) has not been
properly connected.
]Confirm that the source is properly connected.
● All necessary power switches have not been turned on.
]Confirm that all units’ power switches are turned on.
● The setting of the input channel position is inappropriate.
]Select the input channel position (“F-1”, “L-1” or “L-2”) that
corresponds to the input terminal connected to the external
equipment. (墌 pg. 43)
The on-screen display superimposed on the programme played
back/received on this unit is recorded when you dub the
programme to an external recording equipment.
]Set “SUPERIMPOSE” to “OFF”. (墌 pg. 79)
The unit does not operate.
● There are cases when the operation is prohibited on the disc.
● Lightning or static electricity may cause malfunction of the unit.
]Press 1 to turn the power off, then press the button again to
turn the power on.
The remote control of a JVC TV will not operate the unit.
● The setting of the remote control code is inappropriate.
]To operate the unit using a JVC TV remote control, set the
remote control code of the unit to “1” (Default: “3”). (墌 pg. 74)
91Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
EN
91
Playback (DVD Deck)
The DVD deck cannot be operated.
● The DVD deck is not selected.
]Press VHS/DVD on the unit repeatedly or DVD on the remote
control so that the DVD lamp lights up on the unit.
Images do not appear on the TV screen.
● The TV receiver’s channel selector is not set to the AV mode.
]Set the TV to its AV mode.
● When interlace scanned programme is played back, progressive
scan mode is selected.
]Press and hold PROGRESSIVE SCAN until
disappears from
the front display panel. (墌 pg. 80)
Playback does not start or stop immediately after playback is
started by pressing .
On the front display panel, “NO DISC” appears.
● The disc is loaded upside down.
]Place the disc on the disc tray with the playback surface facing
down. (墌 pg. 9)
● A disc not being compatible with the unit is loaded.
]Load a playable disc on the unit. (墌 pg. 6)
● A dirty disc is loaded.
]Clean the disc. (墌 pg. 9)
● Defective disc is loaded.
]Replace the warped or scratched disc with a normal one.
Images are blurred or distorted when you start High-Speed
Search.
]Images are blurred or distorted at the point where the playback
speed changes and this is not a malfunction of the unit.
Playback does not start.
]Playback does not start for approximately 30 seconds after
recording is stopped and this is not a malfunction of the unit.
Filename [MV5SEK_13Subsidiary.fm]
MV5SEK_00.book Page 92 Wednesday, August 31, 2005 7:58 PM
92 EN TROUBLESHOOTING
Playback (VHS Deck)
The VHS deck cannot be operated.
Masterpage:Left+
Recording (VHS Deck)
During recording, the tape does not run. The VHS recording lamp
lights up on the unit.
● The VHS deck is not selected.
]Press VHS/DVD on the unit repeatedly or VHS on the remote
control so that the VHS lamp lights up on the unit.
● The unit is in the Record Pause mode.
]Press 4 to resume recording.
The tape will not rewind or fast-forward.
Recording cannot be done.
● The tape is already fully rewound or fast-forwarded.
]Check the cassette.
● There is no cassette loaded, or the cassette loaded has had its
record safety tab removed.
]Insert a cassette, or using adhesive tape, cover the hole where
the tab was removed.
The playback picture does not appear while the tape is running.
● The TV receiver’s channel selector is not set to the AV mode.
]Set the TV to its AV mode.
Noise appears during visual search.
TV broadcasts cannot be recorded.
● “L-1”, “L-2” or “F-1” has been selected as the input mode.
]Set to the desired channel.
● This is normal.
Camcorder recording is not possible.
Noise appears during normal playback.
● The camcorder has not been properly connected.
]Confirm that the camcorder is properly connected.
● The input mode is not correct.
]Set the input mode to “F-1”.
● The automatic tracking mode is engaged.
]Try manual tracking. (墌 pg. 60)
The playback picture is blurred or interrupted while TV
broadcasts are clear or “USE CLEANING CASSETTE” message
appears on the screen.
● The video heads may be dirty.
]Use a dry cleaning cassette, or consult your JVC dealer.
Breaks are noticeable in Hi-Fi soundtrack.
● The automatic tracking mode is engaged.
]Try manual tracking. (墌 pg. 60)
Recording (DVD Deck)
The desired programme cannot be recorded.
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
(墌 pg. 85)
Recording cannot be made.
● No disc or a disc not being compatible with the unit is loaded.
]Load a recordable disc on the unit. (墌 pg. 6)
● The disc loaded is not formatted.
]Format the disc. (墌 pg. 89)
● A finalised DVD-R disc is loaded.
]Recording cannot be made on finalised discs. Load a recordable
disc on the unit.
● The disc is full or does not have enough space for the title to be
recorded.
]Clear unnecessary titles on the disc or load a blank disc.
(墌 pg. 67)
The tape is automatically stopped and “[’’ on the front display
panel won’t stop blinking.
● The end of the tape was reached during recording.
]The programme may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire programme.
Timer Recording (DVD Deck)
“NO DISC” appears on the front display panel.
● No disc is loaded.
]Press TIMER # so that the DVD timer lamp lights off. Load a
recordable disc, then press TIMER # again.
Timer programming cannot be made.
● Date and time is not correct.
]Set date and time correctly. (墌 pg. 88)
● Timer recording is in progress.
]Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
Timer programming recording does not start.
● Date and time is not correct.
]Set date and time correctly. (墌 pg. 88)
VIDEO Plus+ Timer Programming cannot be made.
● Date and time set on the unit is not correct.
]Set date and time correctly. (墌 pg. 88)
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
(墌 pg. 85)
The VIDEO Plus+ system does not timer-record properly.
● The unit’s channel positions have been set incorrectly.
]Refer to “VIDEO Plus+ System Setup” (墌 pg. 83) and reperform
the procedure.
92Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_13Subsidiary.fm]
MV5SEK_00.book Page 93 Wednesday, August 31, 2005 7:58 PM
Masterpage:Right+
TROUBLESHOOTING
EN
Automatic Satellite Programme Recording does not start.
VIDEO Plus+ Timer Programming cannot be made.
● The satellite receiver is not connected properly to this unit.
]Connect the satellite receiver to the [L-2 IN/DECODER]
connector properly. (墌 pg. 76)
● Date and time set on the unit is not correct.
]Set date and time correctly. (墌 pg. 88)
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
(墌 pg. 85)
On the front display panel, “– –:– –” appears.
● Power failure occurred.
]Set date and time correctly. (墌 pg. 88)
“PROGRAMME FULL” appears on the TV screen during timer
programming.
● 8 programmes have already been timer programmed.
]Clear unnecessary programmes on the unit, then try timer
programming again. (墌 pg. 34)
The disc space does not increase when recorded titles are
cleared.
● The PC’s data recorded on a DVD-RAM drive cannot be cleared
on this unit.
]Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (墌 pg. 9, 89)
Timer Recording (VHS Deck)
“NO TAPE” appears on the front display panel.
● No tape is loaded.
]Press TIMER # so that the VHS timer indicator lights off. Load a
cassette with the record safety tab intact, then press TIMER #
again.
Timer programming cannot be made.
93
The VIDEO Plus+ system does not timer-record properly.
● The unit’s channel positions have been set incorrectly.
]Refer to “VIDEO Plus+ System Setup” (墌 pg. 83) and
reperform the procedure.
Other Problems
The image of the TV broadcast appears distorted on the TV
screen.
For composite connection
]Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator ( ) lights off on the front display panel.
For component video connection
]Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator ( ) lights up on the front display panel.
When scanning channels, some of them are skipped over.
● Those channels have been designated to be skipped.
]If you need the skipped channels, restore them. (墌 pg. 85)
The channel cannot be changed.
● Recording is in progress.
]Press 9 to pause the recording, change channels, then press 4
to resume recording.
● Date and time is not correct.
]Set date and time correctly. (墌 pg. 88)
● The timer is not engaged.
]Press TIMER # and confirm that the VHS timer indicator lights
up on the front panel display.
● Timer recording is in progress.
]Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
● After the manual settings were made, Auto Channel Set was
performed.
]Perform “Manual Channel Set” (墌 pg. 85).
Timer programming recording does not start.
Malfunction occurs and the unit cannot be power off.
● Date and time is not correct.
]Set date and time correctly. (墌 pg. 88)
● The timer is not engaged.
● Press TIMER # and confirm that the VHS timer indicator lights
up on the front panel display.
]Reset the unit by disconnecting the AC power plug from the AC
outlet and connect again.
The VHS timer indicator on the front display panel won’t stop
blinking.
● The timer is engaged but there’s no cassette loaded.
]Load a cassette with the record safety tab intact.
● The loaded cassette has had its record safety tab removed.
]Remove the cassette and cover the hole with adhesive tape, or
insert a cassette with the record safety tab intact.
The tape is automatically stopped and “[’’ and the VHS timer
indicator on the front display panel won’t stop blinking.
● The end of the tape was reached during timer recording.
]The programme may not have been recorded in its
entirety. Next time make sure you have enough time on
the tape to record the entire programme.
● The end of the tape was reached during Instant Timer
Recording.
]The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
93Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Channel settings that were made manually seem to have
changed or disappeared.
Filename [MV5SEK_13Subsidiary.fm]
MV5SEK_00.book Page 94 Wednesday, August 31, 2005 7:58 PM
94 EN TROUBLESHOOTING
On-screen Message
DISC NOT REGISTERED IN THE LIBRARY
REGISTER DISC?
● A disc that is not registered in the library has been inserted.
Register the disc as necessary. (墌 pg. 71)
INSERT DISC #XXXX
● Appears when a title that has been selected in the library is not
contained in the loaded disc.
CAN NOT RECORD OR MAKE PLAY LIST
DELETE UNWANTED TITLES
● Recording and/or editing cannot be performed.
● The number of titles exceeds 99.
● The number of play lists exceeds 999.
SET CLOCK BEFORE TIMER PROGRAMMING
● To set the timer programme, the clock must be set in advance.
(墌 pg. 88)
PROGRAMME FULL
DELETE UNWANTED TIMER PROGRAMME
● You can programme each deck to timer-record as many as 8
programmes. To programme more, you need to cancel a timer
programme already set. (墌 pg. 34)
Masterpage:Left+
COULD NOT FINALISE THIS DISC
CHECK THE DISC
● Finalising is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (墌 pg. 9, 90)
COULD NOT CANCEL DISC FINALISATION
CHECK THE DISC
● Canceling disc finalisation is not complete since the disc may be
dirty or damaged. Take out the disc, clean it and retry. (墌 pg. 9,
90)
PRESS [STOP] AGAIN TO STOP RECORDING
● During Live Memory playback, 8 has been pressed. (墌 pg. 54)
TIMER RECORDING COMPLETED
● Timer recording has finished during Live Memory playback.
PLAYBACK WILL STOP
THEN TIMER RECORDING WILL START
● Timer recording finished during Live Memory playback, then the
next timer recording is about to begin while playback continues.
COPY PROHIBITED
CAN NOT RECORD
● An attempt has been made to record copy-protected contents.
● An attempt has been made to record copy-once contents on a
disc that is not CPRM compatible, such as DVD-R.
NO DISC INSERTED
● Operation has been attempted when a disc is not loaded, or
loaded upside down. (墌 pg. 9)
DISC NOT RECORDABLE
INSERT RECORDABLE DISC
● When a playback-only disc or a finalised disc is loaded, 7 has
been pressed. (墌 pg. 6)
PLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRY
● An invalid PlusCode number has been input. (墌 pg. 29)
GUIDE PROGRAMME IS NOT SET
SELECT CHANNEL YOU WANT TO RECORD
● To set the timer programme using the VIDEO Plus+ system, the
Guide Program Number must be set in advance. (墌 pg. 83)
CAN NOT SET VIDEO PLUS+ TIMER PROGRAMMING DURING
TIMER RECORDING OR INSTANT TIMER RECORDING
CANCEL TIMER RECORDING OR INSTANT TIMER RECORDING
THEN ENTER THE PLUSCODE NO. AGAIN
● Appears when you tried to input a PlusCode number during
timer recording or instant timer recording.
REGION CODE ERROR
CHECK DISC
● A disc loaded cannot be played back on this unit since the region
number of the disc does not match that of the unit. (墌 pg. 7)
UNREADABLE DISC
CHECK DISC
● When an incompatible disc is loaded, 4 has been pressed.
(墌 pg. 7)
COULD NOT FORMAT THE DISC
CHECK THE DISC
● Formatting is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (墌 pg. 9, 89)
94Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
COPY PROHIBITED
CAN NOT PLAY
● The unit has detected invalid contents at the start or in the
middle of playback.
THE i.LINK DEVICE THAT YOU HAVE CONNECTED IS NOT
RECOGNIZED
MAKE SURE THAT THE DEVICE IS CONNECTED PROPERLY
AND POWERED ON
● An attempt has been made to start DV dubbing when a digital
video camera is not properly connected to the unit.
● Check the connection. (墌 pg. 41)
Filename [MV5SEK_13Subsidiary.fm]
MV5SEK_00.book Page 95 Wednesday, August 31, 2005 7:58 PM
Masterpage:Right0
SPECIFICATIONS
EN
GENERAL
VIDEO/AUDIO (VHS Deck)
Power requirement
AC 220 V – 240 Vd, 50/60 Hz
Power consumption
Power on: 38 W
Power off: 7.0 W
Temperature
Operating: 5°C to 35°C
Storage: –20°C to 60°C
Operating position
Horizontal only
Dimensions (WxHxD)
435 mm x 96 mm x 344 mm
Weight
5.8 kg
Input/Output
Video input: 1.0 Vp-p, 75 C (pin jack)
Audio input:
–8 dB, 50 kC (pin jack)
Corresponding to mono (left)
Audio output: –8 dB, 1 kC (pin jack)
21-pin SCART connectors:
IN/OUT x 1, IN/DECODER x 1
Input/Output (DVD Deck Only)
S-video input:
Y: 1.0 Vp-p, 75 C
C: 0.300 Vp-p, 75 C
i.Link: 4-pin for DV input
Component video output:
Y: 1.0 Vp-p, 75 C
CB/CR, PB/PR : 0.7 Vp-p, 75 C
Corresponding to copy protection
Digital audio output: Coaxial
Corresponding to Dolby Digital and DTS Digital Surround
Bit stream
Selectable in digital audio output setting menu
Signal system
PAL colour signal and CCIR monochrome signal, 625 lines/50
fields
Recording system
DA4 (Double Azimuth) head helical scan system
Format
VHS PAL standard
Maximum recording time
(SP): 180 min. with E-180 video cassette
(LP): 360 min. with E-180 video cassette
Signal-to-noise ratio
45 dB
Horizontal resolution
230 lines
Frequency range
(Normal audio): 70 Hz to 10,000 Hz
(Hi-Fi audio): 20 Hz to 20,000 Hz
VIDEO/AUDIO (DVD Deck)
Provided accessories
RF cable,
21-pin SCART cable,
Infrared remote control unit,
“AA” battery x 2
Recording time
Maximum 8 hours (with 4.7 GB disc)
(XP): Approx. 1 hour
(SP): Approx. 2 hours
(LP): Approx. 4 hours
(EP): Approx. 6 hours
(FR): Approx. 1 hour – 8 hours
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Video recording compression system
MPEG2 (CBR/VBR)
95Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
95
Specifications shown are for SP mode unless otherwise specified.
TUNER/TIMER
TV channel storage capacity
99 positions (+AUX position)
Tuning system
Frequency synthesizer tuner
Channel coverage
VHF 47 MHz – 143 MHz/
143 MHz – 470 MHz
UHF 470 MHz – 862 MHz
Memory backup time
Approx. 10 minutes
ACCESSORIES
E.& O.E. Design and specifications subject to change without
notice.
ATTENTION:
This unit contains microcomputers. External electronic noise or
interference could cause malfunctioning. In such cases, switch the
unit off and unplug the AC power cord. Then plug it in again and turn
the unit on. Take out the disc. After checking the disc, operate the
unit as usual.
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Left0
MV5SEK_00.book Page 96 Wednesday, August 31, 2005 7:58 PM
96 EN APPENDIX
Language Code List
AA
Afar
IK
Inupiak
RN
Kirundi
AB
Abkhazian
IN
Indonesian
RO
Rumanian
AF
Afrikaans
IS
Icelandic
RU
Russian
AM
Ameharic
IW
Hebrew
RW
Kinyarwanda
AR
Arabic
JI
Yiddish
SA
Sanskrit
AS
Assamese
JW
Javanese
SD
Sindhi
AY
Aymara
KA
Georgian
SG
Sangho
AZ
Azerbaijani
KK
Kazakh
SH
Serbo-Croatian
BA
Bashkir
KL
Greenlandic
SI
Singhalese
BE
Byelorussian
KM
Cambodian
SK
Slovak
BG
Bulgarian
KN
Kannada
SL
Slovenian
BH
Bihari
KO
Korean (KOR)
SM
Samoan
BI
Bislama
KS
Kashmiri
SN
Shona
BN
Bengali, Bangla
KU
Kurdish
SO
Somali
BO
Tibetan
KY
Kirghiz
SQ
Albanian
BR
Breton
LA
Latin
SR
Serbian
CA
Catalan
LN
Lingala
SS
Siswati
CO
Corsican
LO
Laothian
ST
Sesotho
CS
Czech
LT
Lithuanian
SU
Sundanese
CY
Welsh
LV
Latvian, Lettish
SW
Swahili
DZ
Bhutani
MG
Malagasy
TA
Tamil
EL
Greek
MI
Maori
TE
Telugu
EO
Esperanto
MK
Macedonian
TG
Tajik
ET
Estonian
ML
Malayalam
TH
Thai
EU
Basque
MN
Mongolian
TI
Tigrinya
FA
Persian
MO
Moldavian
TK
Turkmen
FJ
Fiji
MR
Marathi
TL
Tagalog
FO
Faroese
MS
Malay (MAY)
TN
Setswana
FY
Frisian
MT
Maltese
TO
Tonga
GA
Irish
MY
Burmese
TR
Turkish
GD
Scots Gaelic
NA
Nauru
TS
Tsonga
GL
Galician
NE
Nepali
TT
Tatar
GN
Guarani
OC
Occitan
TW
Twi
GU
Gujarati
OM
(Afan) Oromo
UK
Ukrainian
HA
Hausa
OR
Oriya
UR
Urdu
HI
Hindi
PA
Panjabi
UZ
Uzbek
HR
Croatian
PL
Polish
VI
Vietnamese
HU
Hungarian
PS
Pashto, Pushto
VO
Volapuk
HY
Armenian
PT
Portuguese
WO
Wolof
Xhosa
IA
Interlingua
QU
Quechua
XH
IE
Interlingue
RM
Rhaeto-Romance
YO
Yoruba
ZU
Zulu
96Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Right 3Column
MV5SEK_00.book Page 97 Wednesday, August 31, 2005 7:58 PM
APPENDIX
EN
97
TV Station And ID List
The “ID” abbreviation is what is shown on-screen in lieu of the station name. The “ID” abbreviation is listed in the Confirmation screen and
is displayed on the TV screen when the unit is tuned to a different station.
ID*
STATION NAME
ID*
STATION NAME
Anglia TV
ARD
ARTE
BBC Group
BBC1
BBC2
BBCW
Berlin 1
Berlin 2
Border TV
Bayern1
Bayern3
BRT1
BRT2
Children Ch
Canal +
CNN
Channel TV
Central TV
Channel 4
Channel 5
DISC
DRS
DR TV
DSF
Euronews
Euronews
Eurosports
France1
France2
France3
Granada TV
Grampian TV
Hessen1
Hessen3
HRT
HTV
ITV Network
Kabelkanal
London
MDR
MTV
Nord3
NDR1
NDR3
NED1
NED2
NED3
Network 2
NRK
N-TV
Offener Kanal
ORF1
ORF2
ORF3
OWL 3
Premiere
PR07
RAI1
RAI2
RAI3
ANGL
ARD
ARTE
BBC
BBC1
BBC2
BBCW
BLN1
BLN2
BORD
BR1
BR3
BRT1
BRT2
CHLD
CH+
CNN
CHNL
CNTR
CH 4
CH 5
DISC
DRS
DRTV
DSF
EURN
EURO
EURS
FR1
FR2
FR3
GRNA
GRMP
HR1
HR3
HRT
HTV
ITV1
KABL
LNDN
MDR
MTV
N3
NDR1
NDR3
NED1
NED2
NED3
NET2
NRK
N-TV
OKAN
ORF1
ORF2
ORF3
OWL3
PRMI
PR07
RAI1
RAI2
RAI3
RB1
RB3
Rikisutvarpid-S
RTBF 1
RTBF 2
RTE 1
RTL
RTL 2
RTP
SAT
SAT 1
Scottish TV
SC4
SDR
SDR1
SFB1
SFB3
SKY
Sky One
Sky Net
Sport
SR 1
Super RTL
STV Test
STV 1
STV 2
Suedwest3
SWF 1
Schweiz4
TYNE TEES
Text
TF1
TNT int
TRT int
TSI
TSR
TSW
TVE
TV Polonia
TVP 1
TVP 2
TVS
TV2
TV5
Tele Zurich
Ulster TV
Veronica
VIVA
VIVA2
VOX
VTM
VT4
West1
West3
YLE 1
YLE 2
Yorkshire TV
ZDF
Zurich 1
3SAT
RB1
RB3
RKPS
RTB1
RTB2
RTE1
RTL
RTL2
RTP
SAT
SAT1
SCOT
SC4
SDR
SDR1
SFB1
SFB3
SKY
SKY1
SKYN
SPRT
SR1
SRTL
STVT
STV1
STV2
SWR
SWF1
SWZ4
TEES
TEXT
TF1
TNT
TRT
TSI
TSR
TSW
TVE
TVPA
TVP1
TVP2
TVS
TV2
TV5
TZUR
ULST
VERN
VIVA
VIV2
VOX
VTM
VT4
WDR1
WDR3
YLE1
YLE2
YORK
ZDF
ZUR1
3SAT
97Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
Filename [MV5SEK_13Subsidiary.fm]
Masterpage:Left+
MV5SEK_00.book Page 98 Wednesday, August 31, 2005 7:58 PM
98 EN APPENDIX
TV Station Channel Number Guide
Only the main stations are listed. There are in addition many relay stations, and full lists are available from the BBC and ITV.
BBC1 BBC2
London & South-East
Bluebell Hill ........................ 40
Crystal Palace.................... 26
Dover ................................. 50
Heathfield........................... 49
Oxford ................................ 57
ITV
CH4
CH5
46
33
56
52
63
43
23
66
64
60
65
30
53
67
53
—
37
—
—
49
63
28
62
44
26
60
25
59
41
23
53
32
65
47
29
—
—
67
37
—
44
41
47
—
South
Hannington ........................ 39
Midhurst ............................. 61
Rowridge............................ 31
45
55
24
42
58
27
66
68
21
35
—
—
West
Mendip ............................... 58
64
61
54
37
East
Sandy Heath ...................... 31
Sudbury ............................. 51
Tacolneston........................ 62
27
44
55
24
41
59
21
47
65
39
35
52
Midlands
Ridge Hill ........................... 22
Sutton Coldfield ................. 46
The Wrekin ........................ 26
Waltham............................. 58
28
40
33
64
25
43
23
61
32
50
29
54
35
37
35
35
North
Belmont.............................. 22
Emley Moor........................ 44
28
51
25
47
32
41
56
37
South-West
Beacon Hill......................... 57
Caradon Hill ....................... 22
Huntshaw Cross ................ 55
Redruth .............................. 51
Stockland Hill ..................... 33
Channel Islands
Fremont Point .................... 51
98Wednesday, 31 August
19:58
Downloaded FromPage
DvDPlayer-Manual.com
JVC2005
Manuals
BBC1 BBC2
ITV
CH4
CH5
34
62
28
59
32
65
56
48
North-East
Bilsdale West Moor ........... 33
Chatton.............................. 39
Pontop Pike ....................... 58
26
45
64
29
49
61
23
42
54
35
—
68
Scotland
Angus ................................ 57
Black Hill............................ 40
Sandale ............................. 22
Caldbeck ............................—
Creigkelly........................... 31
Darvel ................................ 33
Durris................................. 22
Eitshal ............................... 33
Keelylang Hill..................... 40
Knock More ....................... 33
Rosemarkie ....................... 39
Rumster Forest.................. 31
Selkirk ............................... 55
63
46
—
34
27
26
28
26
46
26
45
27
62
60
43
—
28
24
23
25
23
43
23
49
24
59
53
50
—
32
21
29
32
29
50
29
42
21
65
—
37
—
56
48
35
67
—
—
—
67
—
52
Wales
Blaenplwyf ......................... 31
Carmel............................... 57
Llanddona ......................... 57
Moel-y-Parc ....................... 52
Presely .............................. 46
Wenvoe ............................. 44
27
63
63
45
40
51
24
60
60
49
43
41
21
53
53
42
50
47
56
—
—
—
37
—
Northern Ireland
Brougher Mountain............ 22
Divis .................................. 31
Limavady ........................... 55
28
27
62
25
24
59
32
21
65
—
37
—
North-West
Caldbeck ........................... 30
Winter Hill .......................... 55
Filename [MV5SEK_14IX.fm]
Masterpage:Right0
MV5SEK_00.book Page 99 Wednesday, August 31, 2005 7:58 PM
LIST OF TERMS
EN
99
A
P
A-B Repeat Playback ................................................ 56
Accidental erasure prevention .................................... 63
Adjusting The Picture Quality ..................................... 57
Angle Selection ........................................................ 49
Audio Channel Selection ........................................... 50
Audio Language/Sound Selection ............................... 50
Auto Channel Set ..................................................... 17
Automatic Satellite Programme Recording .................. 36
Pan&Scan ................................................................ 21
PDC recording .......................................................... 30
Play List ................................................................... 68
Playback Control (PBC) Function ............................... 50
Programme Playback .......................................... 58, 72
Progressive scan ...................................................... 80
C
Check, Cancel And Change Programmes ................... 34
Copy-once contents .................................................. 94
CPRM ..................................................................... 94
D
Delete Title .............................................................. 67
Disc menu ............................................................... 47
Disc Resume ........................................................... 80
Discs For Playback Only ............................................. 6
E
Elapsed Recording Time And Disc Remaining Time
Indication ............................................................ 61
Elapsed Recording Time Indication ............................ 63
F
File Structure Of Discs ................................................ 7
Free Rate Function ................................................... 62
G
Q
Quick Rewind A Little ................................................ 59
R
Random Playback ..................................................... 58
Recordable/Playable Discs .......................................... 6
Recording Medium And Format .................................... 7
Recording Mode ................................................. 27, 28
Recording Resume Function ................................ 27, 28
Region Number .......................................................... 7
Register Disc ............................................................ 71
Repeat Playback ................................................ 56, 60
Resume Function ..................................................... 48
S
Select The Switching Interval Of The Slide Show ......... 58
Setting The Progressive Mode ................................... 57
Skip Search ....................................................... 48, 59
Slow Motion ....................................................... 48, 59
Soundtrack Selection ................................................ 60
Still Picture/Frame-By-Frame Playback ................. 48, 59
Subtitle Selection ...................................................... 49
Guide Program Number ............................................ 83
T
H
Tape Remaining Time ............................................... 64
Time Search ............................................................ 57
Top menu ................................................................ 47
High-Speed Search .............................................47, 59
I
Index Search ............................................................ 59
Instant Timer Recording (ITR) ...............................61, 63
Interlaced scan ......................................................... 80
J
U
Unplayable Discs ........................................................ 7
Usable cassettes ...................................................... 25
V
L
VHS Progressive Scan .............................................. 60
Video mode .......................................................... 7, 89
VR mode ............................................................. 7, 89
Language Code List .................................................. 96
Letter Box ................................................................ 21
Live Memory ............................................................ 51
When Programmes Overlap Each Other ..................... 35
Just Clock ................................................................ 88
W
M
Manual Channel Set ................................................. 85
Manual Tracking ....................................................... 60
Marking Positions To Play Back Again Later ................ 49
Menu/Audio/Subtitle Language Set ............................. 20
N
Next Function Memory .............................................. 60
O
On-Disc Timer Programming ..................................... 32
One Touch Replay Function ...................................... 54
One-Touch Expert Dubbing ....................................... 37
On-screen Bar .......................................................... 55
99
Downloaded FromPage
DvDPlayer-Manual.com
JVC Manuals
Wednesday, 31 August 2005 19:58
Filename [MV5SEK_15Cov4.fm]
MV5SEK_00.book Page 100 Wednesday, August 31, 2005 7:58 PM
EN
DR-MV5SEK
DR-MV5BEK
© 2005 Victor Company of Japan, Limited
Page 100Wednesday, 31JVC
August
2005 19:58
Downloaded From DvDPlayer-Manual.com
Manuals
EK
Printed in China
0905TYH-AL-BJ
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement