Ordering Guide 2015

Ordering Guide 2015
Document revision 3.1.0 - Modified on 19/06/2015
Ordering Guide
FALCOM Product List
June 2015
Please pay attention to our changed fax number!
Phone: +49 (0)3677 8042-0
Fax : +49 (0)3677 8042-215
Terms & Conditions
General Terms: See our general terms & conditions on following weblink: http://www.falcom.de/contact/general-terms/
More information: www.falcom.de
|
e-mail: [email protected]
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 1 of 27
Document revision 3.1.0 - Modified on 19/06/2015
Ordering Guide
June 2015
Table Of Contents
AVL DEVICES:
FOX3 ................................................................................................................................................................................................................................................ 3
FOX3-3G .......................................................................................................................................................................................................................................... 3
STEPPIII-UX-X-B1 ........................................................................................................................................................................................................................... 7
BOLERO-LT2-MS-B1 ..................................................................................................................................................................................................................... 10
JAZZ2-GPS+AND4 * ....................................................................................................................................................................................................................... 11
JAZZ2-GPS+GPRS+BT+WIFI+AND4 ............................................................................................................................................................................................ 11
DISCO-CH-B4-AU* ........................................................................................................................................................................................................................ 13
DISCO-B5-MAGNET * ................................................................................................................................................................................................................... 15
ROCK * ........................................................................................................................................................................................................................................... 16
MTR-1-X-RF * ................................................................................................................................................................................................................................ 17
MAMBO2-B6 .................................................................................................................................................................................................................................. 18
PREMIUM FEATURES:
FIRMWARE & HARDWARE PREMIUM FEATURE ....................................................................................................................................................................... 19
EVALUATION KITS:
FOX3/-3G-PROMOTION-KIT ......................................................................................................................................................................................................... 21
BOLERO-LT2-EVALKIT .................................................................................................................................................................................................................. 22
MAMBO2-B6-EVALKIT ................................................................................................................................................................................................................... 23
ORDERING INFORMATION:
ORDERING PROCESS ................................................................................................................................................................................................................. 24
ABBREVIATIONS:
USED ABBREVIATIONS ................................................................................................................................................................................................................ 25
* See notes on each product page
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 2 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
A) AVL DEVICES
FOX3
NONE
Quad Band GSM/GPRS module, high sensitivity GNSS receiver, 3-axis-motion-sensor (±8g), Certifications:
internal antennas, external antenna connectors, 8pin (2x4) main connector, 6pin accessory
CE, E1
connector, 2.5mm audio port and 10pin mini-USB connector. No installation cable included in
standard delivery. It should be ordered separately.
Main Port 8pin (2x4) connector includes:
RX_0, TX_0 : 1 x Serial port V.24 (1st serial interface - SER0)
V+
: 1 x Power supply (10.8 - 32.0 VDC)
IGN :
: 1 x Digital input (Ignition)
I/O :
: 3 x Multi-function inputs/outputs
Accessory Port 6pin (2x3) connector includes:
1-Wire
: 1 x 1-Wire port.
RX_1/TX_1 : 1 x RS-232 port V24 level (2nd serial interface - SER1)
I²C :
: 1 x I²C interface
10pin mini-USB connector includes:
USB
: 1 x USB 2.0 port (DATA+, DATA-, USB detect)
SPI
: 1 x SPI interface (MOSI, MISO, CLK, CS)
Audio port:
2.5mm jack : Microphone + Speaker
NONE
Quad Band GSM/GPRS module with integrated UMTS/HSPA (3G bands: 900/2100 MHz for Certifications:
CE pending
Europe and 850/1900 MHz for America) connectivity, high sensitivity GNSS receiver, 3-axismotion-sensor (±8g), internal antennas, external antenna connectors, 8pin (2x4) main
connector, 6pin accessory connector, 2.5mm audio port and 10pin mini-USB connector.
No installation cable included in standard delivery. It should be ordered separately.
Main Port 8pin (2x4) connector includes:
RX_0, TX_0 : 1 x Serial port V.24 (1st serial interface - SER0)
V+
: 1 x Power supply (10.8 - 32.0 VDC)
IGN :
: 1 x Digital input (Ignition)
I/O :
: 3 x Multi-function inputs/outputs
Accessory Port 6pin (2x3) connector includes:
1-Wire
: 1 x 1-Wire port.
RX_1/TX_1 : 1 x RS-232 port V24 level (2nd serial interface - SER1)
I²C :
: 1 x I²C interface
10pin mini-USB connector includes:
USB
: 1 x USB 2.0 port (DATA+, DATA-, USB detect)
SPI
: 1 x SPI interface (MOSI, MISO, CLK, CS)
Audio port:
2.5mm jack : Microphone + Speaker
Fields of application:
Trucks, Buses, Light trucks,
Special vehicles,
Data logging
FOX3-3G
Fields of application:
Trucks, Buses, Light trucks,
Special vehicles,
Data logging
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 3 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
FOX3/-3G-PROMOTION-KIT NONE
DESCRIPTION
NOTES
See description FOX3/-3G-PROMOTION-KIT, page 21
Accessories for FOX3/-3G
B1
None
Rechargeable 1000 mAh Li-Polymer battery
FAL-ANT-11
None
Combined Quad Band GSM 850/900/1800/1900 and active GPS antenna, incl. 2.5 m RG174
cable set with FAKRA-SMB connectors and double sided adhesive pad (not waterproof).
FAL-ANT-12
None
Combined Penta Band (GSM 850/900/1800/1900, 2.1-2.5GHz) and active GPS antenna incl.
2.5 m RG174 cable set with FAKRA-SMB connectors and double sided adhesive pad (not
waterproof).
CA27
None
Main port programming cable with car charger. This cable connects to the main port of the
FOX3 and consists of the 8pin (2x4) connector, RS-232 port and car charger. Cable length:
1.50 m.
CA31
None
Main port extended installation cable (8/8 wires) with UCOM connector for interfacing
JAZZ2/RFID. This cable connects to the main port of the FOX3/-3G and consists of the 8pin
(2x4) connector, a 4pin (2x2) UCOM connector and 6 x open end wires. Cable length: 1.50 m.
CA68
None
Main port extended installation cable (8/8 wires) with open ends. This installation cable
consists of the 8pin (2x4) double row MOLEX connector and 8 x open end wires.
Cable length: 1.50 m.
CA70
None
Main port basic installation cable (3/8 wires) with open ends. This installation cable consists
of the 8pin (2x4) connector and 3 x wires with open ends. Cable length: 1.50m.
CA69
None
Accessory port cable (6/6 wires) for 1-wire and UCOM connector for interfacing
additional JAZZ2/RFID. This cable connects to the accessory port of the FOX3/-3G and
consists of the 6pin (2x3) connector, a 4pin (2x2) UCOM connector and 6 x open end wires.
Cable length: 1.50 m.
CA71
None
Accessory port cable (6/6 wires) with open ends. This cable connects to the accessory port
of the FOX3/-3G and consists of the 6pin (2x3) connector and 6 x wires with open ends.
Cable length: 1.50 m.
© FALCOM GmbH 2015 | Subject to change without prior notification
FOX3-3G only
Page: 4 of 27
Document revision 3.1.0 - Modified on 19/06/2015
Accessories for FOX3/-3G (continued)
IOBOX-MINI
None
I/O extension module for FOX3/-3G. It extends the functionality of the FOX3/-3G by additional
13 inputs/outputs. The cable "CA38-STEPPIII-KFZ-1,5M" is required for connection of the I/Os
to the vehicle signals/external system. It has 16-wires with a cable length of 1,5 meter. This
cable is not included in the IOBOX-MINI standard delivery, it has to be ordered
separately.
16pin MOLEX connector comprising :
IN
: 8 x Digital inputs
OUT : 4 x Digital outputs
ANA : 1 x Analogue input
Hint: IOBOX-MINI can be used with FOX-IN/EN (with US option) and FOX3/-3G, however the
RX and TX lines on the 16pin connector of the IOBOX-MINI are not supported when
connected to the FOX3 device. These pins are available on the 6-pin accessory port.
For more details, refer to the FOX3/-3G hardware manual.
IOBOX-BT
None
BT4.0 + Bluetooth LE dual mode for FOX3
IOBOX-CAN
None
IOBOX-CAN provides an additional CAN-Bus interface and up to 8 x I/Os, to extend the
functionality of your FOX3/-3G devices, for almost every application within the automobile
industry.
RFID-A-B-EXT
None
12V-24V external passive RFID reader device ISO 14443, Type A/B. It consists of a 4pin
(2x2) UCOM connector and 5.0 m cable length. It connects to the FOX3/-3G device via CA31
cable.
RFID-TAGS-PACK-TYPE-A
A
planned
Passive RFID Transponder (Tag) Type A (10 pcs. or 100 pcs.).
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 5 of 27
Document revision 3.1.0 - Modified on 19/06/2015
FOX3/-3G ACCESSORY MATRIX
Interfaces/
Accessories
Audio
Interface
RFID
RS-232
Interface Interface
CA27
CA31
Bar-Code
Scanner
Interface
JAZZ2
Interface
SPI
interface
1-Wire
interface
Power


CA68

CA71
I²C /
1-Wire
Notes






CA70
CA69
Car
Charger










 - Available
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 6 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
A) AVL DEVICES
STEPPIII-UX-X-B1
X = CH
Fields of application:
Trucks, Buses,
Special vehicles
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver, 3- Certifications:
axis-motion-sensor (±3g), internal rechargeable min. 1000 mAh Li-Polymer battery, external
CE, E1, FCC,
GSM/GPS FAKRA-SMB antenna connectors, 16pin (2x8) connector, 15pin (1x15) connector, SIM
PTCRB, AT&T
card slot, 3 x LED indicators incl. 16pin automotive installation cable 1.5 m.
For programming the device you need CA13 or CA25-A cable.
16pin (2x8) connector includes:
IN
: 7 x Inputs (4 x Digital/Analoge inputs, 3 x Digital inputs)
V+
: 1 x Power supply (10.8 - 32.0 VDC)
IGN
: 1 x Digital input (ignition)
OUT
: 4 x Digital outputs (open collector 100 mA)
15pin (1x15) connector includes:
SERIAL : 2 x RS-232 ports (1 x V.24, 1 x TTL)
SPK/MIC : 1 x Audio interface (for connecting a speaker and microphone device)
IGN
VOUT
CH
: 1 x Digital input (ignition - the same IGN-pin as on 16pin connector)
: 2 x Power outputs (1 x 3.3VD/5VDC, 1 x battery voltage)
CAN-Bus interface (high speed CAN-Bus, CAN-FMS, CAN-OBD-II).
Accessories for STEPPIII-UX-X-B1
FAL-ANT-11
None
Combined Quad Band GSM 850/900/1800/1900 and active GPS antenna incl. 2.5 m RG174
cable set with FAKRA-SMB connectors and double sided adhesive pad (not waterproof).
FAL-ANT-12
None
Combined Penta Band (GSM 850/900/1800/1900, 2.1-2.5GHz) and active GPS antenna incl. 2.5
m RG174 cable set with FAKRA-SMB connectors and double sided adhesive pad (not waterproof).
CA13
None
Programming and audio connection cable with RS-232 serial port and audio jacks. It
consists of a 15pin (1x15) AMP connector, an RS-232 serial port female connector and 2.5mm /
3.5mm female audio jacks.
CA15
None
Audio connection cable with audio jacks. It consists of a 15pin (1x15) AMP connector and
2.5mm/3.5mm female audio jacks.
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 7 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
A) AVL DEVICES
Accessories for STEPPIII-UX-X-B1 (continued)
CA25-X
CA37
X=A
X=B
None
CA38
None
Audio Set
None
Programming and audio connection cable with RS-232 serial port and audio jacks. It
consists of a 15pin (1x15) AMP connector, 2.5mm / 3.5mm female audio jacks, a micro-USB
connector (serial TTL level 3.3V) for connection with MFD1 device, a 4pin (2x2) UCOM connector
for connecting the included RS-232 adapter cable with 4pin (2x2) UCOM connector.
A
RS-232 adapter cable with female connector (for PC).
B
RS-232 adapter cable with male connector for external peripheries (e.g. Serial Barcode Reader).
Adapter cable for connecting STEPPIII with RFID. It consists of a 15-pin (1x15) AMP connector
and a 4-pin (2x2) UCOM connector for connecting RFID-Reader device. Cable length ca. 21 cm.
Automotive connection cable and mounting cradle with 2A-Fuse. The connection cable has a
length of 1.5 m and a 16pin (2x8) connector. The mounting cradle is used to mount the STEPPIII
device
to
a
solid,
flat,
indoor
surface.
Please
refer
to
the
document
"STEPPIII_HardwareManual.pdf" for details, how to mount it.
FALCOM does not offer Audio set device, however it recommends to use active speaker and
microphone. Please refer to the electrical specifications for the MIC and SPK in the STEPPIII
hardware manual.
RFID-A-B-EXT
None
12V-24V external RFID reader device ISO 14443, Type A/B. It consists of a 4pin (2x2) UCOM
connector and 5.0 m cable length. It connects to a STEPPIII device via CA37.
RFID-TAGS-PACK-TYPE-A
None
RFID Transponder (Tag) Typ A (10 pcs. or 100 pcs.).
CON-200
None
Counterpart of the STEPPIII-UX 15pin AMP connector to self build cables. 15-pin (1x15) AMP
connector set (set of 10 pcs).
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 8 of 27
Document revision 3.1.0 - Modified on 19/06/2015
STEPPIII-UX-X-B1 ACCESSORY MATRIX
Interfaces/
Accessories
Audio
RFID
RS-232
Interface Interface Interface
Bar-Code
Scanner
Interface
JAZZ2
Interface
Antenna
interfaces
FAL-ANT-11

FAL-ANT-12

CA13

CA15

CA25-A

*
CA25-B

**
CA37
1-Wire
interface
Power
Car
Charger
Notes



CA38

 - Available; * Female; ** Male;
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 9 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
A) AVL DEVICES
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver Certifications:
and internal GPS/GSM antennas, built-in 3-axis-motion-sensor (±3g), internal rechargeable
CE, E1
1000 mAh Li-Polymer battery, SIM-Card interface, 5pin (1x5) connector, 4 programmable LED
indicators and 1 x free programmable push-button, incl. 3/5pin automotive installation cable
1.5 m and double sided adhesive pad (D=40 mm) for mounting.
BOLERO-LT2 does not support connection to RFID reader or JAZZ2 devices.
* See PREMIUMFor programming the device you need CA43 cable.
FEATURES
5pin (1x5) connector includes:
SERIAL
: 1 x Serial port V.24, for firmware update and configuration ONLY *.
V+
: 1 x Power supply (10.8 - 32.0 VDC)
IGN :
: 1 x Digital input (ignition)
BOLERO-LT2-MS-B1
Fields of application:
Cars, Light trucks,
Motorbikes
Accessories for BOLERO-LT2-MS-B1
CA34
None
Power connection cable with Car Charger. It consists of a 5pin connector and a car charger
with a cable length ca. 2 m.
CA43
None
Programming and power connection cable with RS-232 serial port and open ends. It
consists of 5pin (1x5) MOLEX connector, RS-232 serial port connector and 2 open end wires for
power supply with a cable length of 1.50 m.
Suction foot
(vacuum cup)
None
Suction foot with a 40 mm diameter adhesive pad for mounting BOLERO-LT2 on glass
surfaces. This is a perfect accessory for BOLERO-LT2, when you need to attach it to the
windshield of a car.
BOLERO-LT2-MS-B1 ACCESSORY MATRIX
Interfaces/
Accessories
Audio
RFID
RS-232
Bar-Code
JAZZ2
Antenna
Interface Interface Interface Scanner Interface Interface interfaces
1-Wire
Interface
CA34
CA43

Power
Car
Charger


Notes

 - Available
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 10 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
A) AVL DEVICES (Accessory device for interfacing to AVL devices)
JAZZ2-GPS+AND4*
NONE
Multi functional display 5“ TFT display with integrated built-in 64 channels GPS receiver and internal Certifications: CE
rechargeable battery 2300mAh. Resolution 800 x 480 pixel, 65k resistive touch-screen, embedded
* On request,
CPU 1GHz, 256MB RAM, 512 MB internal flash memory, 2GB FLASH, micro SD card slot, power
depending on
ON/OFF/Back button, USB 2.0 compliant 5 V, Android 4.0.
commercial
FALCOM strongly recommends to use and charge the JAZZ2 only via the AVL Car-Connection-Kit
conditions
(Cradle). If you don't use the JAZZ2 while it is mounted on its cradle, we recommend to switch it off, to
accelerate the charging process.
The standard delivery contents includes:
JAZZ2-GPS+AND4 + USB programming cable + Car charger
JAZZ2GPS+GPRS+BT+WIFI+AND4
NONE
Multi functional display 5“ TFT display with integrated built-in 64 channels GPS receiver, Quad-Band Certifications: CE
GSM/GPRS module, Bluetooth V2.1 (OPP,SPP,...) and WiFi IEEE 802.11 b/g, internal rechargeable
battery 2300mAh. Resolution: 800 x 480 pixel, 65k resistive touch-screen, embedded CPU 1GHz,
256MB RAM, 512 MB internal flash memory, 2GB FLASH , micro SD card slot, power
ON/OFF/Back button, USB 2.0 compliant 5 V, Android 4.0.
FALCOM strongly recommends to use and charge the JAZZ2 only via the AVL Car-Connection-Kit
(Cradle). If you don't use the JAZZ2 while it is mounted on its cradle, we recommend to switch it off, to
accelerate the charging process.
The standard delivery contents includes:
JAZZ2-GPS+GPRS+BT+WIFI+AND4 + USB programming cable + Car charger
Accessories for JAZZ2-GPS+AND4* & JAZZ2-GPS+GPRS+BT+WIFI+AND4
AVL Car-Connection-Kit
None
Car connection kit to connect JAZZ2 to a FALCOM AVL device. This kit consists of a cradle
including: 1.0 m cable with a 4pin (2x2) UCOM connector to connect the JAZZ2 to an AVL device via
one of the following listed cables. It must be ordered together with one of the following cables:
CA31
: FOX-IN/EN installation cable
CA32
: DISCO installation cable
MANDATORY
You may also need the Car-Mounting-Kit (vehicle suction foot) to mount it on your car windshield.
See Car-Mounting-Kit accessory listed below.
Car-Mounting-Kit
None
This car mounting kit allows you to use the JAZZ2 in a car. It consists of a vehicle suction foot which
can be mounted to the JAZZ2 using AVL Car-Connection-Kit or Car-Connection-Kit RS-232.
Car-Mounting-Kit can NOT be mounted directly to the JAZZ2.
Car-Connection-Kit RS232
None
Kit for using the JAZZ2 alone without AVL device. This kit consists of a cradle including: 1.0 m cable
with a RS-232 port and a mini-USB port.
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 11 of 27
Document revision 3.1.0 - Modified on 19/06/2015
JAZZ2-GPS+AND4* & JAZZ2-GPS+GPRS+BT+WIFI+AND4 ACCESSORY MATRIX
Interfaces/
Accessories
Audio
RFID
RS-232
Bar-Code
JAZZ2
Antenna
Interface Interface Interface Scanner Interface Interface interfaces
AVL CarConnection-Kit
1-Wire
Interface
Power
Car
Charger
Notes

Car-Mounting-Kit
Car-ConnectionKit RS-232

 - Available
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 12 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
B) ASSET TRACKING & TERMINAL ASSET DEVICES
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver,
3-axis-motion-sensor (±3g), CAN-Bus interface (high speed CAN-Bus, CAN-FMS, CAN-OBDII), internal battery (rechargeable 2250mAh Li-Polymer), internal GSM/GPS antennas, internal
SIM-card holder, protection class IP69K, mounting kit and external cable (1m) including:
- 2 x Audio jacks (for speaker and microphone),
- 1 x 8pin single row connector for data + power + IO (Input/Outputs),
- 1 x 4pin single row connector for connection to MFD1.
Audio jacks includes:
SPK
: 1 x 3.5mm jack for connecting a speaker device.
MIC
: 1 x 2.5mm jack for connecting a microphone device.
6/8pin (1x8) connector includes:
RX, TX : 1 x Serial port V.24
V+
: 1 x Power supply (10.8 - 32.0 VDC)
IGN
: 1 x Digital input (Ignition)
I/O
: 2 x Multi-function inputs/outputs
4pin (2x2) connector includes:
RX,TX : 1 x RS-232 port 3.3V TTL
V+
: 1 x Power supply for MFD1 device
DISCO-CH-B4-AU*
Fields of application:
Trucks, Buses, Light trucks,
Trains, Special vehicles
* On request,
depending on
commercial
conditions
Accessories for DISCO-CH-B4-AU
CA20
None
Programming and power/charging connection cable with RS-232 serial port and car
charger. This cable consists of 8pin (1x8) connector, RS-232 serial port connector and a car
charger for supplying power to the device. Cable length: 1.50 m
CA32
None
Installation and JAZZ2/RFID connection cable with 2A fuse. This cable consists of the
8pin (1x8) connector, a 4pin (2x2) connector for connecting a JAZZ1/RFID-reader and 6 x
open end wires. Cable length: 1.50 m
Audio Set
None
FALCOM does not offer Audio set device, however it recommends to use active speaker and
microphone.
RFID-A-B-EXT
None
5V-12V External RFID reader device ISO 14443, Type A/B. It consists of a 4pin (2x2)
connector and 5.0 m cable length. It connects to a DISCO-AU device via CA32 cable.
RFID-TAGS-PACK-TYPE-A
None
RFID Transponder (Tag) Typ A (10 pcs. or 100 pcs.).
DISCO-PC-SET-X
X=1
X=2
1 - Pylon Clamp-Set (2 x mast mounting clamps, V4A steel, salt-water proof).
2 - Mounting Kit (Already available in the standard delivery contents).
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 13 of 27
Document revision 3.1.0 - Modified on 19/06/2015
DISCO-CH-B4-AU ACCESSORY MATRIX
Interfaces/
Accessories
Audio
RFID
RS-232
Bar-Code
JAZZ1
Antenna
Interface Interface Interface Scanner Interface Interface interfaces
CA20
CA32
1-Wire
Interface
Power


Car
Charger
Notes



 - Available
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 14 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
B) ASSET TRACKING & TERMINAL ASSET DEVICES
DISCO-B5-MAGNET *
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver, 3axis-motion-sensor (±3g), internal GSM/GPS antennas, internal SIM-card holder, internal
battery pack (5x2250 mAh), protection class IP69K, 6 x magnetic mounts, inside light/dark
sensor, 2 x external buttons for truck mount/demount detections and 6/8pin round female socket
(Flanschdose).
For programming the device you need CA33 cable (see accessory section below).
8pin round female connector (Flanschdose) includes:
RX, TX
: 1 x Serial port V.24
V+
: 1 x Power supply (10.8 - 32.0 VDC)
IGN :
: 1 x Digital input (Ignition)
I/O :
: 3 x Multi-function inputs/outputs
None
Fields of application:
Trucks, Buses, Light trucks,
Trains, Special vehicles
* On request,
depending on
commercial
conditions
4pin (1x4) connector includes:
RX,TX
: 1 x RS-232 port 3.3V TTL
V+
: 1 x Power supply for MFD1 device
Accessories for DISCO-B5-MAGNET
CA33
None
Programming and power/charge connection cable with RS-232 serial port and Wall
Adapter Power Supply. This cable consists of an 8-pin round male-connector (Flanschdose),
an RS-232 serial port connector for configuration and an AC-DC wall adapter power supply
(EU) for charging the internal batteries.
DISCO-B5-MAGNET ACCESSORY MATRIX
Interfaces/
Accessories
CA33
Audio
RFID
RS-232
Interface Interface Interface
Bar-Code
Scanner
Interface
JAZZ1
Interface
Antenna
interfaces
1-Wire
Interface
Power
( Wall Adapter)

Car
Charger
Notes

 - Available
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 15 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
B) ASSET TRACKING & TERMINAL ASSET DEVICES
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver, 3axis-motion-sensor (±3g), internal GSM/GPS antennas, internal SIM-card holder, internal nonrechargeable LR20 battery-block (7V / 5x2250mAh), assembled by 4 standard cross-screws,
IP67 waterproof and shock-resistant case.
None
ROCK *
Fields of application:
Container monitoring,
Data logger
* On request,
depending on
commercial
conditions
Accessories for ROCK
CA44
None
USB programming cable. It consists of a 3pin (1x3) and an USB connector. Please refer to the
ROCK hardware manual for details how to connect this cable with ROCK. To communicate with
ROCK device you have to download and install FTDI driver from this website:
http://www.ftdichip.com
Safety Screw Set ROCK
None
Anti-theft screws ideal to assemble and keep your device safe. This set consists of 4 x
safety screws and corresponding 1 x screwdriver bit.
ROCK Battery-Block
None
ROCK back-up/replacement battery-block 5-cell LR20 battery-block (7,5V/10 Ah) incl. cable
with connector (3pin) to ROCK PCB connection. Please refer to the hardware manual of the
ROCK for details how to replace the battery-pack.
ROCK ACCESSORY MATRIX
Interfaces/
Accessories
CA44
Audio
RFID
USB
Bar-Code
JAZZ1
Antenna
Interface Interface Interface Scanner Interface Interface interfaces
1-Wire
Interface
Power
Car
Charger
Notes

 - Available
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 16 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
Standard version: Complete Terminal with AVL based communication module and integrated
RFID reader (ISO 14443) Type A/B, 4 x free configurable buttons (13.2 x 18.6 mm), 3 x free
programmable LED indicators, internal GSM/GPS antennas, 5.5 mm jack for ext. power supply,
inside SIM card holder, internal Lithium-Ion backup battery (700 mAh) incl. AC/DC power
adapter (110...240V).
* On request,
depending on
commercial
conditions
B) ASSET TRACKING & TERMINAL ASSET DEVICES
X = GPS
MTR-1-X-RF *
Fields of application:
Mobile time registration system
GPS
Built-in 50 channel high sensitivity GPS receiver
Accessories for MTR-1-RF
CA-FOX-8-2x4
None
CA27
None
Adapter cable for CA27 with an 8pin (1x8) and 8pin (2x4) male connectors. It must be ordered
together with CA27. For more details how to connect it to the MTR-1-RF PCB, refer to the MRT1-RF hardware manual.
FOX programming and power connection cable with RS-232 serial port and car charger. It
consists of 8pin (2x4) female connector, RS-232 serial port connector and a car charger
adapter. Cable length: 1.50 m. It must be ordered together with CA-FOX-8-2x4.
MTR-1-X-RF ACCESSORY MATRIX
Interfaces/
Accessories
Audio
RFID
RS-232
Interface Interface Interface
Bar-Code
Scanner
Interface
JAZZ1
Interface
Antenna
interfaces
1-Wire
Interface
Power
Car Charger
Notes
CA-FOX-8-2x4
CA27


 - Available
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 17 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
E) PERSONAL TRACKING DEVICES
MAMBO2-B6
None
Fields of application:
Personal tracker,
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver Certifications: CE, SAR,
based on u-blox chipset, full colour OLED display (128 x 128), 5-way navigation button, 2 x
FCC
control buttons, 1 x reset button, hands-free speaking, internal Li-polymer battery 1650 mAh, 3axis-motion-sensor, customizable GUI, SOS function, man-down detection, SIM card slot,
Internal speaker and microphone, and mini-USB port for data and charging incl. USB-to-miniUSB cable.
The standard MAMBO2-B6 is available in three versions:
1) Orange/Black casing with Silver buttons
2) Black/Black casing with Silver buttons
3) Black/Black casing with Red/Green buttons
Data logger,
Lone worker protection,
Remote worker monitoring,
Racing
Accessories for MAMBO2-B6
Docking-Station
None
Car-Mounting-Kit
None
Docking Station Set with quick charge. This docking station allows you to use your
MAMBO2-B6 in your home, office etc. It consists of the base plate, holding cradle, 9V AC/DC
wall adapter power supply with mini-USB port and EU-,US- or UK-plug. Please refer to the
document "Docking-Station.pdf" for details ,how to assemble it.
Car-Mounting-Kit with Car charger. This car mounting kit allows you to use your
MAMBO2-B6 in a car. This kit consists of vehicle suction foot, holding frame, base plate, USBto-mini-USB power cable, car charger with USB port, 4 x screws and 1 x Allen key ®. Please
refer to the document "Car-Mounting-Kit.pdf" for details, how to assemble it.
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 18 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
F) FIRMWARE & HARDWARE PREMIUM FEATURES FOR AVL DEVICES
The PREMIUM-FEATURES are extensions (APP) which are implemented in the standard FALCOM AVL firmware version 2.11.x
and higher, to provide more applications and additional functionalities. These features need to be activated before use, by
purchasing the corresponding unique activation keys, which are different for each premium feature and AVL device. The activation
keys are linked to the serial numbers of FALCOM devices and will be generated by FALCOM only. A web server will be provided
soon by FALCOM to download these features and allow you to enter the generated keys into the devices yourselves, using the
corresponding PFAL command. The PREMIUM-Features can be individually activated in the AVL devices during installation, as
well as in the AVL devices already deployed in the field.
FIRMWARE & HARDWARE PREMIUM FEATURE
Supported in firmware
version and later
ECO DRIVE GPS
None
ECODrive is a feature based on GPS only. ECOdrive enables fleet managers and drivers
to always keep track of current fuel consumption and driving style for helping them
analyse to improve driving efficiency.
avl_2.11.0_rc7
AES128
None
AES is the Advanced Encryption Standard, a United States government standard
algorithm for encrypting and decrypting data, that offers a higher level of security over
GPRS / TCP using 128-bit group encryption with 128 key length.
avl_2.10.0_rc8
INDEXED HISTORY
None
The indexed history feature enables reading of specific numbers of lines in the history.
Before using this feature you have to clear the old history records in the device.
avl_2.10.0_rc8
EXTENDED-GEOFENCES
None
This extended geofences feature allows you to create up to 3000 geofences and receive
a notification when a geofence event occurs. This feature can be used i.e. for bus
tracking and logistic projects.
avl_2.13.0_rc7
EXTENDED-ALARMS
None
This extended alarm feature extends the number of alarms that can be configured in the
AVL device to up to 250, whereas in the standard AVL firmware versions, the number of
alarms is limited to 100. The increased number of alarms allows you to use more alerts
and thus more flexibility and functionality to the firmware, in order to meet the users'
requirements.
avl_2.13.0_rc7
SERIAL-PORT
(Only for BOLERO-LT2)
None
This feature activates the RS-232 serial port of the BOLERO-LT2 by processing the data
being received from the external devices (e.g. Active & passive RFID readers, Bar-code
scanner or JAZZ2 device) connected to this serial port.
CAN-INTERFACE
(Only for FOX3/-3G)
None
This feature activates the CAN-Bus chip in the FOX3 and forwards CAN/CANFMS /CANOBDII messages in real time to third-parties' application databases.
avl_2.12.0_rc10
RS-485-INTERFACE
(Only for FOX3/-3G)
None
This feature reconfigures the second RS-232 interface in the FOX3 standard hardware
into an RS-485 interface, for the communication with sensors using RS-485 interface.
avl_2.12.0_rc10
© FALCOM GmbH 2015 | Subject to change without prior notification
avl_2.10.0_rc8
Page: 19 of 27
Document revision 3.1.0 - Modified on 19/06/2015
EVALUATION KIT - DESCRIPTION
To evaluate and demonstrate the performance of the AVL device, thus facilitating the placement of
orders, the purchase of its EVALUATION KIT is essential. It comes with following contents:
• 1 x AVL unit shipped pre-configured with all needed accessories
• 1 x Pre-charged SIM-Card supporting GPRS for data transmission
• 1 x 3 Month Free Access to Trace4You Server Frontend
• Access to complete documentation of the dedicated product
• Free support for starting up your project
• Free software and firmware upgrades (for series of standard devices)
Our Evaluation Kits are shipped pre-configured, with all settings needed for fast evaluation and
demonstration. The evaluation board in the Evalkit contains everything needed for helping you to
evaluate your application results. You don’t need anything else than the EVALKIT to get started. In
just a few minutes, you can set up your Evalkit and the AVL device goes online. You only need an
Internet enabled computer (PC client) with a pre-installed standard web browser for accessing the
device from the t4y server frontend. Falcom Workbench-Software tool can be downloaded free of
charge for local evaluation:
see: http://www.falcom.de/support/software-tools/falcom-workbench/
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 20 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
FOX3/-3G-PROMOTION-KIT
OPTIONS
None
DESCRIPTION
NOTES
PROMOTION KIT provides all the necessary hardware, software as well as the access data for
the online documentation and trace4you server to easily and quickly evaluate the product
and its functionalities. RoHS compliant.
PROMOTION-KIT contents:
- 1 x FOX3 or FOX3-3G device pre-configured, with all PREMIUM-FEATURES activated
- 1 x Rechargeable back-up battery
- 1 x FAL-ANT-11 or FAL-ANT-12 (external GSM/GNSS or GSM/3G/GNSS antenna, depending on
the version of the device included in the kit)
- 1 x USB to Serial converter with extension cable
- 1 x CA31 - Main port extended installation cable 1,5m, 8pin double row MOLEX connector, 4pin
double row UCOM connector for connecting RFID reader or JAZZ2 and open ends.
- 1 x CA69 - Accessory port cable 1,5m, 6pin double row MOLEX connector, 4pin double row
UCOM connector and open ends.
- 1 x Control-Box with main and accessory ports containing (cable length: 50 cm) :
- 8pin (2x4) MOLEX connector (it connects to the FOX3 main port).
- 6pin (2x3) MOLEX connector (it connects to the FOX3 accessory port).
- Contol-Box with 5 x LED indicators, 5 x switches, 3 x I/Os and 1 x IGN.
- a 9-pin SUB-D port known in the firmware as "Serial0" - 1st serial interface - SER0.
- Input power jack (12 - 32 VDC)
-
Power supply + US/UK/AU/EU adaptors
1 x Prepaid SIM card. Service fee includes 10MB of data transfer and 3 months access to
the FALCOM trace4you server for evaluation purposes
1 x Info sheet., containing SIM card information, login data for online documentation and
trace4you server).
1 x 8 hours free technical support .
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 21 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
EVALKITS
BOLERO-LT2-EVALKIT
None
Complete plug and play evaluation system for the BOLERO-LT2-MS-B1 device.
RoHS compliant. This delivery consists of 1 box:
Package contents:
1 x BOLERO-LT2-MS-B1 unit shipped pre-configured
1 x BOLERO-LT-EVALBOARD
1 x CA51 cable for connecting device to Evalboard
1 x RS-232 serial cable, connects EVALBOARD to a PC
1 x Double sided adhesive pad (D=40 mm)
1 x EU AC/DC power adapter, type FW7238/12
1 x US adapter
1 x UK adapter
1 x Key for closing and opening the box
1 x 3/5pin Automotive installation cable 1,5m.
1 x Infosheet, contains all information needed to get started with BOLERO-LT2 (SIM
card information, login data for accessing necessary online documentation and
trace4you server frontend).
1 x Prepaid pre-charged SIM card and 3 months access to the FALCOM web server
for evaluation purposes*.
*Attention: The prepaid SIM card is not available for all countries. The 3 months access to the
FALCOM demo web server is not part of the FALCOM’s liabilities but a voluntary offer free-ofcharge for BOLERO-LT2-EVALKIT buyers for evaluation and demonstration purposes and
without responsibility.
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 22 of 27
Document revision 3.1.0 - Modified on 19/06/2015
PRODUCT NAME
OPTIONS
DESCRIPTION
NOTES
EVALKITS
MAMBO2-B6-EVALKIT
None
Complete plug and play evaluation system for the MAMBO2-B6 device. RoHS
compliant. This delivery consists of 1 box:
Package contents:
-
1 x MAMBO2-B6 unit shipped pre-configured
1 x Docking station, consists of base plate, holding cradle, USB-to-mini-USB cable
1 x AC/DC removable adapter (9V output) for different plugs with USB port
1 x EU plug
1 x US plug
1 x UK plug
1 x Key for closing and opening the box
1 x Car mounting kit, consits of vehicle suction foot, holding frame, base plate,
USB-to-mini-USB power cable, car charger with USB port, 4 x screws and 1 x
allen key.
- 1 x Prepaid pre-charged SIM card and 3 months access to the FALCOM web
server for evaluation purposes *.
- 1 x Infosheet, contains all information needed to get started with MAMBO2-B6EVALKIT (SIM card information, login data for accessing necessary online
documentation and trace4you server frontend).
*Attention: The prepaid SIM card is not available for all countries. The 3 months access to the
FALCOM demo web server is not part of the FALCOM’s liabilities but a voluntary offer free-ofcharge for MAMBO2-B6-EVALKIT buyers for evaluation and demonstration purposes and
without responsibility.
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 23 of 27
Document revision 3.1.0 - Modified on 19/06/2015
ORDERING PROCESS
In order to process your PO without any further inquiries, please provide the following information:
Order Information
Description
[COMPANY NAME]
[CUSTOMER P.O. NO]
[DATE OF P.O.]
[BILLING ADDRESS]
[VAT-NO]
[SHIPPING ADDRESS]
[INCOTERM]
[PREFERRED CARRIER]
Depending of the INCOTERM
[CARRIER ACCOUNT-NO]
[CONTACT DETAILS]
Details of the recipient at the delivery address incl. name and phone number.
[PRODUCT NAME]
As stated in Ordering Guide, including options.
[QUANTITY]
[PRICE]
See price list or SQ.
[REQUESTED DELIVERY DATE]
Optional.
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 24 of 27
Document revision 3.1.0 - Modified on 19/06/2015
USED ABBREVIATIONS
Abbreviation
Meaning
Abbreviation
Meaning
EOL
End Of Life
USB
Universal Serial Bus
ODM
Original Design Manufacturer
SPI
Serial Peripheral Interface
MOQ
Minimum Order Quantity
RS-232
Recommended Standard 232 (EIA standard for transmitting serial data)
LTB
Last Time Buy
CAN
Controller Area Network
LTD
Last Time Delivery
FMS
Fleet Management Systems
NPI
New Product Introduction
OBD-II
On Board Diagnostics, 2nd generation
GSM
Global Standard for Mobile Communications
I/O
Multi function input/output
GPS
Global Positioning System
VDC
Volts Direct Current
GLONASS
Global Navigation Satellite System (Russia)
TFT
Thin Film Transistor
SIM
Subscriber Identification Module
SD
Secure Digital
GPRS
General Packet Radio Service
CPU
Central Processing Unit
IGN
Ignition
RAM
Random Access Memory
SPK
Speaker
DDR
Double Data Rate
MIC
Microphone
SPP
Serial Port Profile (Bluetooth)
OUT
Digital Output
RFID
Radio-Frequency IDentification
IN
Digital Input
OLED
Organic Light-Emitting Diode
TTL
Transistor-Transistor-Logic
GUI
Graphical User Interface
LED
Light-Emitting Diode
AES
Advanced Encryption Standard
RX
Receive direction
SQ
Special quote.
TX
Transmit direction
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 25 of 27
Document revision 3.1.0 - Modified on 19/06/2015
FALCOM GmbH products are RoHS conform
FALCOM GmbH  Gewerbering 6  98704 Langewiesen  Germany  Phone: +49 (0)3677 8042-0  Fax: +49 (0)3677 8042-215  e-mail: [email protected]  Web: www.falcom.de
Terms & Conditions
General Terms: See our general terms & conditions on following weblink: http://www.falcom.de/contact/general-terms/
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 26 of 27
Document revision 3.1.0 - Modified on 19/06/2015
Document history:
Version
Changes
Modified
3.1.0
Extended: FOX3/3G PROMOTION-KIT contents (new added: USB to Serial converter + FAL-ANT-11 or FAL-ANT-12 + 8 hours free technical support)
19/06/2015
3.0.9
Some made corrections
12/06/2015
3.0.8
Changed ordering-options for devices: STEPPIII-UX, DISCO, BOLERO-LT2 (see the product page)
Changed Fax number
05/06/2015
3.0.7
Some made corrections
04/06/2015
3.0.6
Added new devices: FOX3-3G and IOBOX-CAN
Renamed: FOX3-STARTERKIT to FOX3/3G PROMOTION-KIT
Extended: FOX3/3G PROMOTION-KIT contents (SIM card + trace4you access)
Removed devices: FOX-IN/EN (all versions), JAZZ1
Removed EVALKITS: FOX3, STEPPIII-UX, FOX-IN/EN, DISCO
03/06/2015
2.0.6
- Extended: FOX3-EVALKIT contents - CA69 cable added.
20/02/2015
2.0.5
- Updated: FOX3/-3G-PROMOTION-KIT contents.
- Changed: PAID-Features to PREMIUM FEATURES.
19/02/2015
2.0.4
- Changed Hint: IOBOX-MINI can be used with FOX-IN/EN and FOX3.
- Removed the accessory "Leather-Bag" for MAMBO2.
08/12/2014
2.0.3
- Added CA68 (main port installation cable 8pin connector with open ends) for FOX3
24/10/2014
2.0.2
- Added STARTERKIT for FOX3
06/10/2014
2.0.1
- Added paid-features: EXTENDED-GEOFENCES, EXTENDED-ALARMS
30/09/2014
2.0.0
- Added: FOX3 and FOX3-EVALKIT
- Added: Premium-features for FOX3 (only): CAN-INTERFACE & RS-485-INTERFACE
19/09/2014
1.1.1
- Added DISCO-B5-MAGNET-EVALKIT (this version is still not released)
09/01/2014
1.0.1
- JAZZ-2 is offered without camera
01/07/2013
1.0.0
- Initial version
14/06/2011
© FALCOM GmbH 2015 | Subject to change without prior notification
Page: 27 of 27
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement