ifs d7100 series install & oper instr

ifs d7100 series install & oper instr
D7120
D7120-R3
D7120WDM
D7120WDM-R3
D7130WDM
D7130WDM-R3
IFS Fiber Module
Installation & Operation
Instructions
P/N 1062848 • REV B • ISS 01AUG11
D7130WDM
OPTICAL ETHERNET TRANSCEIVER
UP
1 2 3
-- AUTO NEGOTIATE
-- SPEED
ifs
FIBER IN/OUT
International
Fiber
Systems
Incorporated
10 BASE -T / 100 BASE - TX
-- DUPLEX
FIBER LINK
FIBER LINK CONTACT
AUTO NEGOTIATE ON/OFF
POWER
POWER
-2
+12 VDC - 1
Simplex single mode
fiber optic cable
D7130WDM
OPTICAL ETHERNET TRANSCEIVER
FIBER IN/OUT
UP
1 2 3
-- AUTO NEGOTIATE
-- SPEED
ifs
International
Fiber
Systems
Incorporated
10 BASE -T / 100 BASE - TX
-- DUPLEX
FIBER LINK
FIBER LINK CONTACT
AUTO NEGOTIATE ON/OFF
POWER
POWER
-2
+12 VDC - 1
D7100
C
B
A
D
E
F
G
H
J
I
1
2
1
2
A Fiber Link
B Auto Negotiate ON/OFF
C Power
D
E
F
G
H
I
J
Auto Negotiate Switch
Speed Switch
Duplex Switch
Power Connector
Fiber Link Contact Connector
10 Base-T / 100 Base-TX Connector
Fiber Optic Connectors
(1 or 2 depending on model number)
LED illuminates
LED illuminates
LED illuminates
UP
DOWN
SWITCH #
ON
OFF
1
10
100
2
FULL
HALF
3
D7100 NOTES
Descriptions of Operation
a. Fiber Link LED
OFF = No fiber connection
GREEN = Fiber connection
b. Auto-negotiate LED OFF = Auto-negotiate off
GREEN = Auto - negotiate on
c. Default, recommended operation mode is auto - negotiate ON. When NOT using
auto - negotiate mode, a cross over cable must be used for the copper link segment.
Both ends of the copper link must be fixed at the same speed and duplex rating.
d. Auto - negotiate ON/OFF When auto - negotiate is ON, all capabilities for the
twisted pair interface are advertised including auto - mdi/mdi-x (auto detection for
straight cables vs. cross-over).
e. Speed Switch - Active only when auto - negotiate is OFF. The speed switch forces
the link setting to either 10 or 100.
f. Duplex Switch - active only when auto - negotiate is OFF. The duplex switch
forces the duplex rating to either full or half duplex.
g. h. Fiber Link Contact Connector -
OPEN = No fiber OR Power Off
CLOSED = Fiber connected
i. 10 base - T/100 base - TX Connector - The LED in the upper LEFT corner indicates
copper link status. Link = Green
The LED in the upper RIGHT corner indicates copper link speed:
GREEN = 100 mbs
ORANGE = 10 mbs
j. -
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesirable operation.
Changes or modifications not expressly approved by International Fiber Systems, Inc. could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
CLASS 1 LASER PRODUCT
(For purposes of IEC 60825-1)
Complies with FDA Performance Standard for Laser Products
Title 21
Code of Federal Regulations
Subchapter J
Comprehensive
Lifetime Warranty
(a) Seller warrants to the original End User that products and any
services furnished hereunder will be free from defects in material
and workmanship as of the date of delivery, and will conform to
Seller’s published technical specifications. The foregoing shall
apply only to failures to meet said warranties which appear within
that period of time during which the Products are installed in their
original installation for the original End User and operator of such
Products; provided, however, that in the event of product discontinuance, warranty support is limited to five (5) years from the
announcement of discontinuance. Notwithstanding the preceding
sentence, the duration of the warranty period for products not
manufactured by Seller (e.g., fiber optic cabling, test equipment,
power supplies or batteries) shall be the warranty period offered by
the original manufacturer, if any.
(b) The conditions of any tests shall be mutually agreed upon and
Seller shall be notified of, and may be represented at, all tests that
may be made. The warranties and remedies set forth herein are
conditioned upon (a) proper storage, installation, use and maintenance, and conformance with any applicable recommendations of
Seller and (b) Buyer promptly notifying Seller of any defects and,
if required, promptly making the product available for correction.
(c) If any product or service fails to meet the foregoing warranties,
Seller shall thereupon correct any such failure either at its option,
(i) by repairing any defective or damaged product or parts of the
products, or (ii) by making available any necessary repaired or
replacement products or parts thereof. Any repaired or replacement
part or product shall be warranted for the remaining period of the
original Warranty Period. Seller shall pay, or credit Buyer for, the
cost of freight for all return shipments of products or parts to
Buyer. Where a failure cannot be corrected by Seller's reasonable
efforts, the parties will negotiate an equitable adjustment in price.
(d) The preceding paragraph sets forth the exclusive remedies for
claims based on defect in or failure of products or services,
whether the claim is in contract, indemnity, warranty, tort
(including Seller's negligence), strict liability or otherwise and
however instituted. Upon the expiration of the warranty period,
all such liability shall terminate and BUYER shall have a reasonable time, within thirty days after the warranty period, to give
written notice of any defects which appeared during the warranty
period. The foregoing warranties are exclusive and in lieu of all
other warranties, whether written, oral, implied or statutory.
NO IMPLIED OR STATUTORY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE SHALL APPLY. Seller does not warrant any
products or services of others which BUYER has designated.
Contacting us
For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any
other documentation provided. If you still have questions, contact us during business hours (Monday through
Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time).
Sales and support contact information
North
America
Toll-free: 855.286.8889 in the US, including Alaska and Hawaii;
Puerto Rico; Canada.
Outside the toll-free area: 503.885.5700.
E-mail: [email protected]
Europe
Select Contact Us at www.utcfssecurityproducts.eu
Australia
[email protected]
Note: Be ready at the equipment before calling.
Online
Another great resource for assistance with your Interlogix product is our online publication library. To access
the library, go to our website at the following location:
http://www.interlogix.com/transmission1
1.
Many Interlogix documents are provided as PDFs (portable document format). To read these documents, you will
need Adobe Reader, which can be downloaded free from Adobe’s website at www.adobe.com.
Product Disassembly Instructions for WEEE
Per European Directive 2002/95/EC Waste Electrical and
Electronic Equipment
Required Tools:
One number 2 Phillips (crosstip) screwdriver.
One number 2 flat screwdriver.
For the enclosed box version:
1. Locate and remove box cover securement screws. Usually, but not limited to, at least
4 screws.
2. Lift off box top cover.
3. Locate and remove securement screws for printed circuit board.
4. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
5. Lift off printed circuit board.
6. Disassembly of box version of product is complete.
For rack version:
1. Locate and remove securement screws for printed circuit board. Usually, but not
limited to, at least 4 screws.
2. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
3. Lift off printed circuit board(s).
4. Disassembly of rack card version of product is complete.
Copyright
Trademarks and
patents
Manufacturer
Certification
ACMA compliance
Canada
European Union
directives
© 2011 UTC Fire & Security. All rights reserved.
Interlogix and IFS names and logos are trademarks of
UTC Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
N4131
Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
2004/108/EC (EMC directive): Hereby, UTC Fire & Security
declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive
2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information, see www.interlogix.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement