Cisco | WAP54GX | User guide | Cisco WAP54GX User guide

USER GUIDE
Wireless-G Access Point
Model: WAP54G
About This Guide
About This Guide
Icon Descriptions
While reading through the User Guide you may see
various icons that call attention to specific items. Below is
a description of these icons:
NOTE: This check mark indicates that there is
a note of interest and is something that you
should pay special attention to while using the
product.
WARNING: This exclamation point indicates
that there is a caution or warning and it is
something that could damage your property or
product.
WEB: This globe icon indicates a noteworthy
website address or e-mail address.
Online Resources
Website addresses in this document are listed without
http:// in front of the address because most current web
browsers do not require it. If you use an older web browser,
you may have to add http:// in front of the web address.
Resource
Website
Linksys
www.linksys.com
Linksys International
www.linksys.com/international
Glossary
www.linksys.com/glossary
Network Security
www.linksys.com/security
Copyright and Trademarks
Linksys, Cisco and the Cisco Logo are
registered trademarks or trademarks
of Cisco Systems, Inc. and/or its
affiliates in the U.S. and certain other
countries. Copyright © 2008 Cisco
Systems, Inc. All rights reserved.
Other brands and product names are
trademarks or registered trademarks
of their respective holders.
Wireless-G Access Point
i
Table of Contents
Chapter 1: Product Overview
4
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 2: Wireless Security Checklist
5
General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2: Using the Linksys Wireless Guard Service
6
Client Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Network Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Your Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 3: Configuring the Wireless-G Access Point
12
How to Access the Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How to Navigate within the Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
The Setup Tab > Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
The Setup Tab > AP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
The Wireless Tab > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
The Wireless Tab > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
The Wireless Tab > Wireless MAC Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
The Wireless Tab > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 18
The Administration Tab > Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
The Administration Tab > SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
The Administration Tab > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
The Administration Tab > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
The Administration Tab > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
The Status Tab > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
The Status Tab > Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Appendix A: Troubleshooting
23
Appendix B: Specifications
24
Appendix C: Warranty Information
25
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Appendix D: Regulatory Information
27
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Avis d’Industrie Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Avis de non-responsabilité concernant les appareils sans fil . . . . . . . . . . . . . . . . . . 28
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Wireless-G Access Point
ii
Table of Contents
Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Appendix E: Software License Agreement
33
Software in Linksys Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Software Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Wireless-G Access Point
iii
Product Overview
Chapter 1
Chapter 1:
Product Overview
Thank you for choosing the Wireless-G Access Point. Use
the instructions in this User Guide to help you connect
the Access Point, set it up, and configure it to bridge your
different networks. These instructions should be all you
need to get the most out of the Access Point.
Front Panel
Link
Act (Green) The Activity LED lights up when
the Access Point is ready for wireless use. It
flashes when the Access Point is transmitting or
receiving data wirelessly.
Link (Orange) The Link LED lights up when
the Access Point is successfully connected
to a device through the Ethernet network
port. The LED flashes when the Access Point
is transmitting or receiving data through the
Ethernet network port.
Back Panel
Cisco logo (Orange/White) The Cisco logo
is the Access Point’s SecureEasySetup button.
It lights up when the Access Point is powered
on. The Cisco logo is orange when the
SecureEasySetup feature is not used, while the
color white indicates that the SecureEasySetup
feature is being used. When the Access Point
enters SecureEasySetup mode, the Cisco logo
will turn white and start flashing. Then the
Access Point will generate its SSID (network
name) and WPA-Personal (also called WPA-PSK)
key. If the Access Point successfully associates
with a client using SecureEasySetup, the
Cisco logo will stop flashing and stay white.
If the association is unsuccessful, then the
Cisco logo will stop flashing and stay orange.
To clear the SSID and WPA-Personal key, press
and hold down the Cisco logo for ten seconds.
The Cisco logo will turn orange to indicate a
successful reset.
NOTE: SecureEasySetup is a feature
that makes it easy to set up your
wireless network. If you have
SecureEasySetup devices, run the
Setup Wizard on the Access Point’s
Setup Wizard CD-ROM. Then follow
the on-screen instructions.
Power
Act
LAN The Ethernet network port connects to
an Ethernet network device, such as a switch or
router.
RESET There are two ways to reset the Access
Point’s factory defaults. Either press the Reset
button for approximately ten seconds, or use
the Administration > Factory Defaults screen of
the Access Point’s Web-based Utility.
NOTE: Resetting the Access Point will
erase all of your settings (including
wireless security, IP address, and
power output) and replace them with
the factory defaults. Do not reset the
Access Point if you want to retain
these settings.
POWER The Power port connects to the Access
Point’s power adapter.
Power (Red) The Power LED lights up when the
Access Point is powered on.
Wireless-G Access Point
4
Wireless Security Checklist
Chapter 2
Chapter 2:
Wireless Security Checklist
Wireless networks are convenient and easy to install, so
homes with high-speed Internet access are adopting them
at a rapid pace. Because wireless networking operates by
sending information over radio waves, it can be more
vulnerable to intruders than a traditional wired network.
Like signals from your cellular or cordless phones, signals
from your wireless network can also be intercepted. Since
you cannot physically prevent someone from connecting
to your wireless network, you need to take some additional
steps to keep your network secure.
1. Change the default wireless network name or SSID
Wireless devices have a default wireless network name
or Service Set Identifier (SSID) set by the factory. This
is the name of your wireless network, and can be up
to 32 characters in length. Linksys wireless products
use linksys as the default wireless network name. You
should change the wireless network name to something
unique to distinguish your wireless network from other
wireless networks that may exist around you, but do not
use personal information (such as your Social Security
number) because this information may be available for
anyone to see when browsing for wireless networks.
2. Change the default password
For wireless products such as access points, routers, and
gateways, you will be asked for a password when you
want to change their settings. These devices have a default
password set by the factory. The Linksys default password
is admin. Hackers know these defaults and may try to
use them to access your wireless device and change your
network settings. To thwart any unauthorized changes,
customize the device’s password so it will be hard to
guess.
3. Enable MAC address filtering
4. Enable encryption
Encryption protects data transmitted over a wireless
network. Wi-Fi Protected Access (WPA/WPA2) and Wired
Equivalency Privacy (WEP) offer different levels of security
for wireless communication.
A network encrypted with WPA/WPA2 is more secure
than a network encrypted with WEP, because WPA/WPA2
uses dynamic key encryption. To protect the information
as it passes over the airwaves, you should enable the
highest level of encryption supported by your network
equipment.
WEP is an older encryption standard and may be the
only option available on some older devices that do not
support WPA.
General Network Security Guidelines
Wireless network security is useless if the underlying
network is not secure.
•• Password protect all computers on the network and
individually password protect sensitive files.
•• Change passwords on a regular basis.
•• Install anti-virus software and personal firewall
software.
•• Disable file sharing (peer-to-peer). Some applications
may open file sharing without your consent and/or
knowledge.
Additional Security Tips
•• Keep wireless routers, access points, or gateways away
from exterior walls and windows.
•• Turn wireless routers, access points, or gateways
off when they are not being used (at night, during
vacations).
•• Use strong passphrases that are at least eight characters
in length. Combine letters and numbers to avoid using
standard words that can be found in the dictionary.
WEB: For more information on wireless
security, visit www.linksys.com/security
Linksys routers and gateways give you the ability to
enable Media Access Control (MAC) address filtering. The
MAC address is a unique series of numbers and letters
assigned to every networking device. With MAC address
filtering enabled, wireless network access is provided
solely for wireless devices with specific MAC addresses.
For example, you can specify the MAC address of each
computer in your home so that only those computers can
access your wireless network.
Wireless-G Access Point
5
Configuration
Chapter 2
Chapter 2:
Using the Linksys Wireless
Guard Service
3. The next screen will tell you to close all other
applications before continuing. If no other applications
are open, click Next to continue. If you want to exit to
close your other applications, click Cancel.
This chapter is only for users who have signed up for
Linksys Wireless Guard to secure their network and have
configured the Access Point for Linksys Wireless Guard. (For
information on configuring the Access Point for Linksys
Wireless Guard, refer to the Quick Installation Guide.)
You will now install the client software needed to securely
connect a PC to the Access Point that is protected by
Linksys Wireless Guard. This chapter will also show you
how to access your protected network and manage your
account.
Client Software Installation
1. If you haven’t already done so, on the Welcome screen
of the Setup Wizard on the CD-ROM, click Linksys
Wireless Guard Client. The Note screen shown below
will appear. To install the software on this PC, click
Continue. Click Cancel to cancel the installation.
Exit Other Applications
4. A license agreement will appear next. Scroll down or
press PAGE DOWN to read the entire agreement. To
accept the terms and continue the installation, click
Yes. To quit the installation, click No.
Note
2. A screen will appear to notify you that the setup is in
process. Wait until the next screen appears. If you want
to end the installation process, click Cancel.
License Agreement
Configuring Windows Installer
Wireless-G Access Point
6
Configuration
Chapter 2
5. On this screen, you will be informed where the
Linksys Wireless Guard client software will be
installed. To install to this folder, click Next. If
you want to choose a different location for the
folder, click Browse and select the location.
7. The Linksys Wireless Guard client software is
successfully installed. Before you can use the program,
you must restart your computer. Select Yes to restart
your computer now. Select No to restart your computer
at a later time. Remove any disks that are in their drives,
and then click Finish.
Click Back to return to the previous screen. Click
Cancel to cancel the installation.
Restart Your Computer
Destination Location
6. The InstallShield Wizard will start
program files. Click Next to continue.
copying
Click Back to return to the previous screen. Click
Cancel to cancel the installation.
8. After the Linksys Wireless Guard client software is
installed, a key icon will be displayed on the right side
of the system tray at the bottom of your screen. The
color of the key will change according to the status of
the network connection. The most common colors are
described below.
Key Icon
•• Green - Connected.
•• Green with Red X - Connected, but waiting for
authentication.
•• Gray - Not connected.
•• Red - Connected to a network that is not
protected by Linksys Wireless Guard.
Copying Files
Wireless-G Access Point
7
Configuration
Chapter 2
Network Access
Your Account
After Linksys Wireless Guard is installed, any time you
access a Linksys Wireless Guard protected network, the
Wireless Guard Login screen will appear. To access your
network, click Login as a Wireless Guard Member, or if
you are a guest, click Login as a Wireless Guard Guest.
Enter your user name and password, and then click
Login.
This section explains how to access your account, how to
add a guest, how to add another member to your account,
and how to secure and unprotect the Linksys Wireless
Guard network.
For more detailed information on your account and the
website, click your computer’s Start button, select the
Linksys Wireless Guard folder, and then click Linksys
Wireless Guard Help. For further information on Linksys
Wireless Guard only, you can contact Linksys Wireless
Guard Technical Support at 888 231-5506 or send an
e-mail to wirelessguard@linksys.com.
Accessing Your Account
Right-click on the green Wireless Guard Network key
icon, and then click View Membership and Network
Administration Website to log in to the Linksys Wireless
Guard website.
You can also click on your computer’s Start button,
select the Linksys Wireless Guard folder, then click
Membership and Network Administration Website.
1. The Member Login screen will appear. Enter the
administrator’s user name and password in the fields
provided. Click Login.
Wireless Guard Login Screen
Login as a Wireless Guard Member Select this option if
you are a registered member.
Login as a Wireless Guard Guest Select this option if
you are a registered guest member. The guest must first
be added as a guest at the Membership and Network
Administration Website. Refer to Add a Guest, page 9.
Save Password Select this if you want the system to
remember your password so you don’t have to enter it
when you log in.
Enable Auto Login Select this if you want the system to
bypass the login.
Click Cancel to cancel the login, or if you forget your
password, click Lost Password.
Wireless-G Access Point
Member Login Screen
2. The Wireless Guard Member Website home screen
will appear. Through this website, you can modify
your member or billing profile, view information
about your account or subscription, add or remove
members, modify access privileges of members and
guests, change network settings, and download
updates and documentation. There is a Help tab with
extensive information to help you with everything on
the website. The instructions for adding a guest or
member, as well as securing and unprotecting your
network, are also explained below.
8
Configuration
Chapter 2
Add a Guest
1. On the Wireless Guard Member Website home screen,
click the Network Admin tab.
4. The Add Guest screen will appear. Enter the Guest User
Name, Guest First Name, Guest Last Name, Password,
Password Verify, and Access Duration. Then click
Submit.
Home
2. The Network Administration screen will appear.
Under Network Administration, click Modify Access
Control.
Add Guest
Guest User Name Enter a user name of the guest you
want to add.
Guest First Name Enter the first name of the guest
you want to add.
Guest Last Name Enter the last name of the guest
you want to add.
Password Enter a password that’s at least six
characters long for the guest you want to add.
Password Verify Enter the password again.
Network Administration
3. The Modify Access Control screen will appear. Under
Guests, click Add Guest.
Access Duration Enter the length of time (in hours)
that the guest will be on the network.
5. The guest will need to install the Linksys Wireless
Guard Client software on his or her PC. The software
can be downloaded from the Setup CD-ROM or from
www.linksys.com/support. Refer to Client Software
Installation, page 6.
Modify Access Control
Wireless-G Access Point
9
Configuration
Chapter 2
Add a Member
To add a member, follow the instructions in steps 1
through 3 of Add a Guest, page 9, except in step 3, click
Add Member.
The Add Member screen will appear. Registered members
can enter their e-mail address in the field provided and
select the duration for access from the drop-down menu.
If you want this network member to have the authority to
put the network in Fallback Mode in case network security
is lost, select Permission to Initiate Network Fallback.
When finished, click Submit.
3. When the Subscriber information screen appears, enter
the first and last names, phone number, if desired,
and then e-mail address of the new member. Click
Next.
Click Back to return to the previous screen. Click
Cancel to cancel the member registration.
Subscriber Information
Add Member
To register as a member for Linksys Wireless Guard, refer to
the following instructions, and then when you are finished
with the registration process, return to this screen.
The member will need to install the Linksys Wireless Guard
Client software on his or her PC. The software can be
downloaded from the Setup CD-ROM or from linksys.com/
support. Refer to Client Software Installation, page 6.
4. When the next screen appears, choose who will be
paying for the account. If the new member will be
paying for the account, click I will pay for my own
subscription. I will enter my billing information
on the web site later. If the administrator will be
paying for the account, click Another member will be
paying for my subscription. Click Next.
Click Back to return to the previous screen. Click
Cancel to cancel the member registration.
Member Registration
1. Right-click on the green Wireless Guard Network key
icon, and then click Register Member.
2. The Welcome screen will appear. Click Next.
Account Finances
Welcome
Wireless-G Access Point
10
Configuration
Chapter 2
5. When this screen appears, enter the information you
will be using with the account. Enter a user name and
password, and then enter the password again. Also select
a security question and answer in case you forget your
password in the future. Click Next to continue.
Click Back to return to the previous screen. Click
Cancel to cancel the member registration.
Securing or Unprotecting Your Wireless Guard
Network
There may be some instances when you would want to
completely unprotect your network connection so it is not
using the Wireless Guard security. For example, if you take
your laptop to another location to give a presentation, and
connect to a network that is running 802.1x security, the
Linksys Wireless Guard software on your laptop will block
you from logging in to another network. You will need to
manually unprotect your network connection so you can
log in. When you come back to your own network, you
won’t have to manually re-secure the network connection.
Linksys Wireless Guard will recognize it and automatically
reinstate security.
To unprotect a network
Right-click the green Wireless Guard Network key icon
on the right-side of the system tray at the bottom of your
screen. Select Unprotect this Network Connection from
the menu.
Credentials Information
6. When the Congratulations screen appears, you will be
successfully registered for Linksys Wireless Guard. Click
Finish.
When the screen asks if you’re sure you want to unprotect
the network, click Yes.
To secure an unprotected network
Right-click the green Wireless Guard Network key icon.
Select Secure this Network Connection from the menu.
When the screen asks if you’re sure you want to secure the
network, click Yes.
NOTE: For more detailed information on your
account and the website, click your computer’s
Start button, select the Linksys Wireless
Guard folder, and then click Linksys Wireless
Guard Help.
Congratulations
7. You should now ask the administrator to add you to
his or her Wireless Guard Protected Network’s Access
Control List. To do so, the network administrator needs
to return to the Add Member screen (refer to Add a
Member, page 10).
Wireless-G Access Point
11
Configuration
Chapter 3
Chapter 3:
Configuring the Wireless-G
Access Point
How to Navigate within the Utility
The Access Point has been designed to be functional
right out of the box, with the default settings in the Setup
Wizard. However, if you want to change these settings, the
Access Point can be configured through your web browser
with the Web-based Utility. This chapter explains how to
use the Utility.
The Setup Tab > Network Setup
There are four main tabs: Setup, Wireless, Administration,
and Status. When you select a main tab, the screens for
that tab are listed below the main tab. To display a screen,
click its name in the list.
The first screen that appears is the Network Setup screen.
This allows you to change the Access Point’s general
settings.
The Utility can be accessed via a web browser through use
of a computer that is networked with the Access Point.
For a basic network setup, most users only have to use the
following screens of the Utility:
•• Setup On the Setup > Network Setup screen, enter
your basic network settings here.
•• Management Click the Administration tab and then
select the Management screen. To secure the Access
Point, change the password from the default value
(admin). Enter a new password in the Password and
Re-enter to confirm fields.
Setup > Network Setup (Automatic Configuration - DHCP)
How to Access the Web-Based Utility
To access the web-based utility of the Access Point, launch
your web browser. In the Address field, enter the Access
Point’s default IP address, 192.168.1.245, or the IP address
you entered during the Setup Wizard. (Should you need to
learn what IP address the Access Point presently uses, run
the Setup Wizard again. It will scan the Access Point and
give you its IP address.) Press Enter.
Internet Explorer Address Bar
The login screen will appear. Leave the User Name field
blank. The first time you open the Web-based Utility, use
the default password, admin. (You can set a new password
from the Administration > Management screen.) Then click
OK.
Setup > Network Setup (Static IP)
Network Setup
Device Name
You may assign any Device Name to the Access Point.
Unique, memorable names are helpful, especially if you are
employing multiple access points on the same network.
Configuration Type
Select Automatic Configuration - DHCP if your network
router will assign an IP address to the Access Point. The
Access Point’s IP Address, Subnet Mask, and Default
Gateway address will then be displayed.
Login Screen
Wireless-G Access Point
Select Static IP if you want to assign a static or fixed IP
address to the Access Point. Then complete the following:
12
Configuration
Chapter 3
IP Address The IP address must be unique to your
network. It is recommended to use the default IP address
of 192.168.1.245.
Subnet Mask The Subnet Mask must be the same as that
set on your Ethernet network.
Default Gateway Enter the IP address of your network’s
gateway. The gateway is the device that enables
communication between your computers and the
Internet. In most cases, your router acts as your gateway.
Change these settings as described here and click
Save Settings to apply your changes, or click
Cancel Changes to cancel your changes. Click Help for
more information.
The Setup Tab > AP Mode
On this screen you can change the Access Point’s mode
of operation. In most cases, you can keep the default,
Access Point. You may wish to change the Access Point’s
mode of operation if you want to use the Access Point as
a wireless repeater to extend the range of your wireless
network. You may also wish to change the Access Point’s
mode of operation if you want to use the Access Point as
a wireless bridge; for example, you can use two Access
Points in Wireless Bridge mode to connect two wired
networks that are in two different buildings.
AP Mode
The Access Point offers four modes of operation: Access
Point, AP Client, Wireless Repeater, and Wireless Bridge.
For the Repeater and Bridge modes, make sure the SSID,
channel, and security settings are the same for the other
wireless access points/devices.
LAN MAC Address
The MAC address of the Access Point is displayed here.
Access Point The AP Mode is set to Access Point by
default. This connects your wireless PCs to a wired network.
In most cases, no change is necessary.
AP (Access Point) Client When set to AP Client mode, the
AP Client is able to talk to one remote access point within
its range. This feature only works with another Wireless-G
Access Point (model number: WAP54G).
This mode allows the AP Client to act as a client of a remote
access point. The AP Client cannot communicate directly
with any wireless clients. A separate network attached to
the AP Client can then be wirelessly bridged to the remote
access point.
To use this mode, select AP Client and enter the LAN
MAC address of the remote access point in the Remote
Access Point’s LAN MAC Address field. If you do not know
the remote access point’s MAC address, click Site Survey.
Select the access point you want to use and click Close. If
you do not see the access point you want, click Refresh to
search for access points again.
Site Survey
Setup > AP Mode
NOTE: For the AP Client and Wireless Bridge
modes, the remote access point must be a
second Linksys Wireless-G Access Point (model
number: WAP54G). For the Wireless Repeater
mode, the remote wireless bridge must be a
second Linksys Wireless-G Access Point (model
number: WAP54G) or Wireless-G Router (model
number: WRT54G).
Wireless-G Access Point
Wireless Repeater When set to Wireless Repeater mode,
the Wireless Repeater is able to talk to up a remote access
point within its range and retransmit its signal. This feature
only works with the Linksys Wireless-G Router (model
number: WRT54G) or another Wireless-G Access Point
(model number: WAP54G).
To configure a Wireless Repeater environment, select
Wireless Repeater and enter the MAC address of the
remote access point in the Remote Access Point’s LAN MAC
Address field.
13
Configuration
Chapter 3
Wireless Bridge Diagram
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
The Wireless Tab > Basic Wireless Settings
Change the wireless network settings on this screen.
Wireless Repeater Diagram
Wireless Bridge This mode connects two physically
separated wired networks using two access points (use
additional access points to connect more wired networks).
This feature only works with another Wireless-G Access
Point (model number: WAP54G).
To configure a Wireless Bridge environment, select
Wireless Bridge, and enter the MAC addresses of the
wireless bridges/access points in the Remote Wireless
Bridge’s LAN MAC Addresses fields. You will also need to
set the remote wireless bridges/access points to Wireless
Bridge mode.
NOTE: In Wireless Bridge mode, the Access Point
can ONLY be accessed by another access point
in Wireless Bridge mode. In order for your other
wireless devices to access the Access Point, you
must reset it to Access Point mode. The two
modes are mutually exclusive.
Wireless > Basic Wireless Settings
Basic Wireless Settings
Configure the Access Point using the available settings.
Mode Select Mixed to allow both Wireless-G and
Wireless-B computers on the network, but with the
speed reduced. Select G-Only for maximum speed with
Wireless-G products only. The final selection, B-Only,
allows only Wireless-B products on the network. To disable
wireless performance, select Disabled.
Network Name (SSID) Enter the name of the Access
Point’s wireless network.
Wireless-G Access Point
14
Configuration
Chapter 3
Channel Select the appropriate channel from the list
provided; this will be the channel that all of your wireless
devices will use.
When the SecureEasySetup process is complete, the Basic
Wireless Settings screen will appear, and the Current
Encryption and Status information will be updated.
SSID Broadcast This feature allows the SSID to be
broadcast by the Access Point. You may want to enable
this function while configuring your network, but make
sure that you disable it when you are finished. With this
enabled, someone could easily obtain the SSID information
with site survey software and gain unauthorized access to
your main network. Click Enabled to broadcast the SSID
to all wireless devices in range. Click Disabled to increase
network security and block the SSID from being seen on
networked PCs.
Current Encryption This shows the encryption method
currently used by the Access Point.
SecureEasySetup Button The status of the Access Point’s
SecureEasySetup feature is displayed here. If you want to
use the Access Point’s SecureEasySetup feature, click the
SecureEasySetup button.
NOTE: If you have already set up your network
using your router’s SecureEasySetup feature,
then you cannot use the Access Point’s
SecureEasySetup feature. You must manually
configure the Access Point’s wireless settings to
match your existing network’s settings.
NOTE: SecureEasySetup uses WPA Personal
encryption. If your current wireless devices
do not support WPA Personal security, then
you cannot use SecureEasySetup on your
network. You will need to manually configure
your network security using the encryption
supported by your existing devices.
You will be asked to press the SecureEasySetup button
(hardware or software) on your wireless client (computer
or other network device) within two minutes to complete
the SecureEasySetup process. Click OK to continue.
SecureEasySetup Completed Screen
NOTE: You can only add one SecureEasySetup
device at a time. For additional devices, click
SecureEasySetup on the Wireless > Basic
Wireless Settings screen and repeat the process.
Reset Security If you already set up the network using
the Access Point’s SecureEasySetup feature and you want
to replace your current settings with new SecureEasySetup
settings, click Reset Security. A new screen will appear.
You will be asked to confirm that you want to reset your
wireless security settings. Click OK to continue.
Confirm Reset
The Access Point will generate a new network name (SSID)
and set of keys. To configure your wireless network using
SecureEasySetup, return to the previous page of this User
Guide and follow the instructions for the SecureEasySetup
button.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
Press the SecureEasySetup Button for Your Wireless Client
A new screen will be displayed while the Access Point is
waiting for you to push the SecureEasySetup button on
your wireless client.
Waiting for Completion of SecureEasySetup
Wireless-G Access Point
15
Configuration
Chapter 3
The Wireless Tab > Wireless Security
WPA2-Personal
Change the Access Point’s wireless security settings on
this screen.
Wireless Security
Security Mode Select the security method you want
to use, WPA-Personal, WPA2-Personal, WPA2-Mixed,
WPA-Enterprise, RADIUS, or WEP. (WPA stands for WiFi Protected Access, which is a security standard stronger
than WEP encryption. WPA2 is a stronger version of WPA.
WEP stands for Wired Equivalent Privacy, while RADIUS
stands for Remote Authentication Dial-In User Service.)
Refer to the appropriate instructions below. For detailed
instructions on configuring wireless security for the Access
Point, refer to Chapter 2: Wireless Security Checklist,
page 5. To disable such security, select Disabled.
WPA-Personal
Wireless > Wireless Security (WPA2-Personal)
Encryption AES is automatically selected as the
encryption method.
Passphrase Enter a Passphrase (also called a WPA Shared
Key) of 8-32 characters.
Key Renewal Enter a Key Renewal timeout period, which
instructs the Access Point how often it should change the
encryption keys.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
WPA2-Mixed
Wireless > Wireless Security (WPA-Personal)
Encryption WPA offers you two encryption methods,
TKIP and AES, with dynamic encryption keys. Select the
type of algorithm you want to use, TKIP or AES.
Passphrase Enter a Passphrase (also called a WPA Shared
Key) of 8-32 characters.
Key Renewal Enter a Key Renewal timeout period, which
instructs the Access Point how often it should change the
encryption keys.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
Wireless > Wireless Security (WPA2-Mixed)
Encryption TKIP + AES is automatically selected so both
methods can be used.
Passphrase Enter a Passphrase (also called a WPA Shared
Key) of 8-32 characters.
Key Renewal Enter a Key Renewal timeout period, which
instructs the Access Point how often it should change the
encryption keys.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
WPA-Enterprise
This option features WPA used in coordination with a
RADIUS server. (This should only be used when a RADIUS
server is connected to the Access Point.)
Wireless-G Access Point
16
Configuration
Chapter 3
Shared Secret Enter the Shared Secret key used by the
Access Point and RADIUS server.
Encryption Select a level of WEP encryption, 40/64 bits
(10 hex digits) or 128 bits (26 hex digits).
Passphrase To generate WEP keys using a Passphrase,
enter the Passphrase and click the Generate key.
Wireless > Wireless Security (WPA-Enterprise)
Encryption WPA offers you two encryption methods,
TKIP and AES, with dynamic encryption keys. Select the
type of algorithm you want to use, TKIP or AES.
RADIUS Server Enter the RADIUS server’s IP address.
RADIUS Port Enter the port number used by the RADIUS
server.
Key 1-4 If you want to manually enter WEP keys, then
complete the fields provided. Each WEP key can consist of
the letters “A” through “F” and the numbers “0” through “9”.
It should be 10 characters in length for 64-bit encryption
or 26 characters in length for 128-bit encryption.
TX Key Select which Key to use for data transmissions.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
WEP
Shared Secret Enter the Shared Secret key used by the
Access Point and RADIUS server.
Key Renewal Enter a Key Renewal timeout period, which
instructs the Access Point how often it should change the
encryption keys.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
RADIUS
This option features WEP used in coordination with a
RADIUS server. (This should only be used when a RADIUS
server is connected to the Access Point.)
Wireless > Wireless Security (WEP)
Encryption Select a level of WEP encryption, 40/64 bits
(10 hex digits) or 128 bits (26 hex digits).
Passphrase To generate WEP keys using a Passphrase,
enter the Passphrase and click Generate.
Key 1-4 If you want to manually enter WEP keys, then
complete the fields provided. Each WEP key can consist of
the letters “A” through “F” and the numbers “0” through “9”.
It should be 10 characters in length for 64-bit encryption
or 26 characters in length for 128-bit encryption.
TX Key Select which Key to use for data transmissions.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
Wireless > Wireless Security (RADIUS)
RADIUS Server Enter the RADIUS server’s IP address.
RADIUS Port Enter the port number used by the RADIUS
server.
Wireless-G Access Point
17
Configuration
Chapter 3
The Wireless Tab > Wireless MAC Filter
This screen allows you to permit or block wireless access
for computers with specific MAC addresses.
The Wireless Tab > Advanced Wireless
Settings
This screen allows you to configure the advanced settings
for the Access Point. In most cases, these settings do not
need to be changed.
Wireless > Advanced Wireless Settings
Wireless > Wireless MAC Filter
Wireless MAC Filter
Access Restriction
If you want to control access to your wireless network,
select Enable. If you do not wish to filter users by MAC
address, select Disable.
To deny access, click Prevent PCs listed below from
accessing the wireless network. To permit access,
click Permit PCs listed below to access the wireless
network.
MAC 01-25 Enter the MAC addresses of the computers
whose access you want to control. If you want to list more
than 25 MAC addresses, then select MAC Addresses
26~50 from the drop-down menu.
Click Clear to delete the MAC addresses you have
entered.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
Advanced Wireless
You can change the data transmission and output power
settings for the Access Point.
Authentication Type Select the authentication method
you want the Access Point to use, Shared Key or Open
System (Default). Shared Key is when both the sender
and the recipient share a WEP key for authentication.
Open System is when the sender and the recipient do not
share a WEP key for authentication. All devices on your
network must use the same authentication type. In most
cases, keep the default, Open System (Default).
Basic Rates This setting is not actually one rate of
transmission but a series of rates that are advertised
to the other wireless devices in your network, so they
know at which rates the Access Point can transmit. At
the Default setting, the Access Point will advertise that
it will automatically select the best rate for transmission.
Other options are 1-2Mbps, for use with older wireless
technology, and All, when you wish to have all rates
advertised. The Basic Data Rates are not the rates
transmitted; the rates transmitted can be configured
through the Transmission Rates setting on this screen.
Transmission Rates The range is from 1 to 54Mbps.
The rate of data transmission should be set depending
on the speed of your wireless network. You can select
from a range of transmission speeds, or you can keep the
default setting, Auto (Default), to have the Access Point
automatically use the fastest possible data rate and enable
the Auto-Fallback feature. Auto-Fallback will negotiate the
best possible connection speed between the Access Point
and a wireless client.
Wireless-G Access Point
18
Configuration
Chapter 3
Transmission Power You can adjust the output power
of the Access Point to get the appropriate coverage for
your wireless network. Select the level you need for your
environment. If you are not sure which setting to choose,
then keep the default setting, Full (Default).
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
CTS Protection Mode The CTS (Clear-To-Send) Protection
Mode function boosts the Access Point’s ability to catch
all Wireless-G transmissions but will severely decrease
performance. Select Enable if you want to permanently
enable this feature, or keep the default, Disable, if you
want to permanently disable this feature. In most cases,
CTS Protection Mode should remain disabled, unless the
Wireless-G products are experiencing severe problems
trying to transmit to the Access Point in an environment
with heavy 802.11b traffic.
On this screen you can configure the password as well as
back up or restore the Access Point’s configuration file.
The Administration Tab > Management
Frame Burst Mode Enabling this option should reduce
overhead and enhance your network performance,
depending on the manufacturer of your wireless products.
If you are not sure how to use this option, keep the default,
Disabled.
Administration > Management
Antenna Selection This selection is for choosing which
antenna transmits data, left or right. If you are not sure
which antenna to use, keep the default, Diversity, to
increase reception.
Management
Beacon Interval. This value indicates the frequency
interval of the beacon. A beacon is a packet broadcast
by the Access Point to keep the network synchronized. A
beacon includes the wireless networks service area, the
Access Point address, the Broadcast destination addresses,
a time stamp, Delivery Traffic Indicator Maps, and the
Traffic Indicator Message (TIM).
AP’s Password
DTIM Interval This value indicates how often the Access
Point sends out a Delivery Traffic Indication Message
(DTIM). Lower settings result in more efficient networking,
while preventing your PC from dropping into powersaving sleep mode. Higher settings allow your PC to
enter sleep mode, thus saving power, but interferes with
wireless transmissions.
Backup and Restore
Fragmentation Threshold This specifies the maximum
size a data packet can be before splitting and creating a
new packet. It should remain at its default setting of 2346.
A smaller setting means smaller packets, which will create
more packets for each transmission. If you have decreased
this value and experience high packet error rates, you can
increase it again, but it will likely decrease overall network
performance. Only minor modifications of this value are
recommended.
Restore Settings To upload a configuration file to the
Access Point, click Restore Settings and follow the onscreen instructions.
You should change the password that controls access to
the Access Point’s Web-based Utility.
Password Create a Password for the Access Point’s Webbased Utility.
Re-enter to Confirm To confirm the new Password, enter
it again in this field.
On this screen you can create a backup configuration file
or save a configuration file to the Access Point.
Backup Settings To save a backup configuration file on
a computer, click Backup Settings and follow the onscreen instructions.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
RTS Threshold. This setting determines how large
a packet can be before the Access Point coordinates
transmission and reception to ensure efficient
communication. This value should remain at its default
setting of 2347. Should you encounter inconsistent data
flow, only minor modifications are recommended.
Wireless-G Access Point
19
Configuration
Chapter 3
The Administration Tab > SNMP
The Administration Tab > Log
SNMP is a popular network monitoring and management
protocol. It provides network administrators with the
ability to monitor the status of the Access Point and
receive notification of any critical events as they occur on
the Access Point.
On this screen you can configure the log settings.
Administration > Log
Management
You can have logs that keep track of the Access Point’s
activities.
Administration > SNMP
SNMP V1/V2c
To enable the SNMP support feature, select Enable.
Otherwise, select Disable.
Contact Enter the name of the contact person, such as a
network administrator, for the Access Point.
Device Name Enter the name you wish to give to the
Access Point.
Location Enter the location of the Access Point.
SNMP Community
Log
To enable the Log support feature, select Enabled.
Otherwise, select Disabled.
Logviewer IP Address If you have chosen to monitor
the Access Point’s traffic, then you can designate a PC that
will receive permanent log files periodically. In the field
provided, enter the IP address of this PC. To view these
permanent logs, you must use Logviewer software, which
can be downloaded free of charge from www.linksys.
com.
View Log To see a temporary log of the Access Point’s
most recent activities, click this button. The View Log
screen appears.
You can have up to two passwords. Then select the level of
access you want to assign to each password.
(public) Enter the first password that allows access to the
Access Point’s SNMP information. The default is public.
Then select the level of access you want to assign, ReadOnly or Read/Write.
(private) Enter the second password that allows access
to the Access Point’s SNMP information. The default is
private. Then select the level of access you want to assign,
Read-Only or Read/Write.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
Wireless-G Access Point
View Log Screen
On the View Log screen, click First Page to see the first page
of log entries. Click Last Page to see the last page of log
entries. Click Previous Page to see the previous page of
log entries, and click Next Page to see the next page of log
entries. To delete all log entries, click Clear Log. To update
the log with the most recent activities, click Refresh.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Click Help for more information.
20
Configuration
Chapter 3
The Administration Tab > Factory Defaults
1. Download the firmware upgrade file from the Linksys
website, www.linksys.com.
On this screen you can restore the Access Point’s factory
default settings.
2. Extract the firmware upgrade file on your computer.
3. On the Firmware Upgrade screen, enter the location of
the firmware upgrade file in the field provided, or click
Browse to find the file.
4. Click Upgrade, and follow the on-screen instructions.
You can also click Cancel to cancel the upgrade, or
click Help for more information.
Click Help for more information.
The Status Tab > Local Network
Administration > Factory Defaults
Management
The Local Network screen displays the Access Point’s
current status information for the local network.
Write down any custom settings before you restore the
factory defaults. Once the Access Point is reset, you will
have to re-enter all of your configuration settings.
Factory Defaults
Restore Factory Defaults To restore the Access Point’s
factory default settings, click this button. Then follow the
on-screen instructions.
Click Help for more information.
The Administration Tab > Firmware
Upgrade
On this screen you can upgrade the Access Point’s firmware.
Do not upgrade the firmware unless you are experiencing
problems with the Access Point or the new firmware has a
feature you want to use.
Status > Local Network
AP’s Information
Firmware Version This is the version of the Access Point’s
current firmware.
Local Network
MAC Address The MAC Address of the Access Point’s
Local Area Network (LAN) interface is displayed here.
AP’s IP Address This shows the Access Point’s IP address,
as it appears on your local network.
Subnet Mask This shows the Access Point’s Subnet
Mask.
Default Gateway Displayed here is the IP address of the
Access Point’s Default Gateway.
Click Help for more information.
Administration > Firmware Upgrade
Firmware Upgrade
Before you upgrade the Access Point’s firmware, write
down all of your custom settings. After you upgrade its
firmware, you will have to re-enter all of your configuration
settings. To upgrade the Access Point’s firmware:
Wireless-G Access Point
21
Configuration
Chapter 3
The Status Tab > Wireless Network
The Wireless Network screen displays the Access Point’s
current status information for its wireless network.
Status > Wireless Network
Wireless Network
MAC Address The MAC Address of the Access Point’s
wireless interface is displayed here.
Mode The Access Point’s mode is displayed here.
Network Name (SSID) The Access Point’s main SSID is
displayed here.
Channel The Access Point’s channel setting for wireless
broadcast is shown here.
Security The wireless security setting for the Access Point
is displayed here.
SSID Broadcast Shown here is the setting of the Access
Point’s SSID Broadcast feature.
Click Help for more information.
Wireless-G Access Point
22
Appendix A
Appendix A:
Troubleshooting
Troubleshooting
WEB: If your questions are not addressed here,
refer to the Linksys website, www.linksys.com
I can’t connect to the Internet.
1. Verify the proper LEDs are lit on the Access Point.
•• Make sure the Power LED has a steady green light
and is not flashing.
•• Verify the Ethernet LED has a fairly steady green
light. It will flash occasionally, indicating activity.
•• Verify the Signal Strength LEDs are lit.
2. Power down everything, and power on each device in
the following order:
•• Access Point
•• PC
3. Ensure that the proper wireless network name (SSID)
has been selected. You can use the Site Survey button
on the Wireless > Basic Wireless Settings screen (refer to
The Wireless Tab > Basic Wireless Settings, page 14)
to scan for a list of available wireless network names
(SSIDs). If necessary, check with your ISP to verify the
proper wireless network name (SSID).
4. Make sure that you are using the proper encryption
settings required by your ISP to connect to their
service. The encryption settings of the Access Point are
configured on the Wireless > Wireless Security screen
(refer to The Wireless Tab > Wireless Security , page
16).
The wireless signal strength is very poor.
•• Try moving the location of the Access Point, if possible
move the Access Point near a window.
•• Adjust the direction of the antenna.
I cannot access the web-based utility after my computer
goes into sleep mode.
Disconnect the power from the Access Point and reconnect
it. You should be able to access the web-based utility once
the Access Point has fully booted.
I need to modify the settings on my Access Point.
1. Open your web browser.
2. Type your Access Point’s IP address into the address
bar (the default IP address is 192.168.1.245).
3. When prompted, enter the user name and password
for your Access Point. (The default user name is none
[leave the field blank], and the default password is
admin.)
4. Click the appropriate tab to change the settings.
Wireless-G Access Point
23
Specifications
Appendix B
Appendix B:
Specifications
Model
WAP54G
Standards
IEEE 802.11g, IEEE 802.11b,
IEEE 802.3, IEEE 802.3u
Ports
One 10/100 Auto-Cross Over
(MDI/MDI-X) port, power port
Buttons
Reset, SES (SecureEasySetup)
Cabling Type
RJ-45
LEDs
Power, Activity, Link,
SecureEasySetup
Transmit Power
802.11g: Typ. 13.5 ± 2 dBm @
Normal Temp Range
802.11b: Typ. 16.5 ± 2 dBm @
Normal Temp Range
Security Features
WPA, Linksys Wireless Guard,
WEP Encryption, MAC Filtering,
SSID Broadcast enable/disable
WEP Key Bits
64/128-bit
Environmental
Dimensions
7.32" x 1.89" x 6.65"
(186 x 48 x 169 mm)
Weight
16.23 oz. (460 g)
Power
External, 12V DC
Certification
FCC
Operating Temp.
32 to 150ºF (0 to 40ºC)
Storage Temp.
-40 to 185ºF (0 to 70ºC)
Operating Humidity
10 to 85% Noncondensing
Storage Humidity
5 to 90% Noncondensing
Wireless-G Access Point
24
Appendix C
Appendix C:
Warranty Information
Limited Warranty
Linksys warrants this Linksys hardware product against
defects in materials and workmanship under normal
use for the Warranty Period, which begins on the date of
purchase by the original end-user purchaser and lasts for
the period specified below:
•• One (1) year for new product
•• Ninety (90) days for refurbished product
This limited warranty is non-transferable and extends only
to the original end-user purchaser. Your exclusive remedy
and Linksys’ entire liability under this limited warranty
will be for Linksys, at its option, to (a) repair the product
with new or refurbished parts, (b) replace the product
with a reasonably available equivalent new or refurbished
Linksys product, or (c) refund the purchase price of the
product less any rebates. Any repaired or replacement
products will be warranted for the remainder of the
original Warranty Period or thirty (30) days, whichever is
longer. All products and parts that are replaced become
the property of Linksys.
Exclusions and Limitations
This limited warranty does not apply if: (a) the product
assembly seal has been removed or damaged, (b) the
product has been altered or modified, except by Linksys, (c)
the product damage was caused by use with non‑Linksys
products, (d) the product has not been installed, operated,
repaired, or maintained in accordance with instructions
supplied by Linksys, (e) the product has been subjected to
abnormal physical or electrical stress, misuse, negligence,
or accident, (f ) the serial number on the Product has been
altered, defaced, or removed, or (g) the product is supplied
or licensed for beta, evaluation, testing or demonstration
purposes for which Linksys does not charge a purchase
price or license fee.
ALL SOFTWARE PROVIDED BY LINKSYS WITH THE
PRODUCT, WHETHER FACTORY LOADED ON THE
PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING
THE PRODUCT, IS PROVIDED “AS IS” WITHOUT WARRANTY
OF ANY KIND. Without limiting the foregoing, Linksys does
not warrant that the operation of the product or software
will be uninterrupted or error free. Also, due to the
continual development of new techniques for intruding
upon and attacking networks, Linksys does not warrant
that the product, software or any equipment, system or
network on which the product or software is used will be
free of vulnerability to intrusion or attack. The product
may include or be bundled with third party software or
Wireless-G Access Point
Warranty Information
service offerings. This limited warranty shall not apply to
such third party software or service offerings. This limited
warranty does not guarantee any continued availability
of a third party’s service for which this product’s use or
operation may require.
TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIED
WARRANTIES AND CONDITIONS OF MERCHANTABILITY,
SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED TO THE DURATION OF THE
WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED
CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED.
Some jurisdictions do not allow limitations on how long
an implied warranty lasts, so the above limitation may not
apply to you. This limited warranty gives you specific legal
rights, and you may also have other rights which vary by
jurisdiction.
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT
WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE
THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING
OUT OF OR RELATED TO THE USE OF OR INABILITY TO
USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN
IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY
EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.
The foregoing limitations will apply even if any warranty
or remedy provided under this limited warranty fails of
its essential purpose. Some jurisdictions do not allow
the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not
apply to you.
Obtaining Warranty Service
If you have a question about your product or experience a
problem with it, please go to www.linksys.com/support
where you will find a variety of online support tools and
information to assist you with your product. If the product
proves defective during the Warranty Period, contact
Linksys Technical Support for instructions on how to
obtain warranty service. The telephone number for Linksys
Technical Support in your area can be found in the product
User Guide and at www.linksys.com. Have your product
serial number and proof of purchase on hand when calling.
A DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED
TO PROCESS WARRANTY CLAIMS. If you are requested to
return your product, you will be given a Return Materials
Authorization (RMA) number. You are responsible for
properly packaging and shipping your product to Linksys
at your cost and risk. You must include the RMA number
and a copy of your dated proof of original purchase when
returning your product. Products received without a RMA
number and dated proof of original purchase will be
25
Appendix C
Warranty Information
rejected. Do not include any other items with the product
you are returning to Linksys. Defective product covered
by this limited warranty will be repaired or replaced and
returned to you without charge. Customers outside of
the United States of America and Canada are responsible
for all shipping and handling charges, custom duties,
VAT and other associated taxes and charges. Repairs or
replacements not covered under this limited warranty will
be subject to charge at Linksys’ then-current rates.
Technical Support
This limited warranty is neither a service nor a support
contract. Information about Linksys’ current technical
support offerings and policies (including any fees for
support services) can be found at: www.linksys.com/support.
This limited warranty is governed by the laws of the
jurisdiction in which the Product was purchased by you.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,
CA 92623.
Wireless-G Access Point
26
Regulatory Information
Appendix D
Appendix D:
Regulatory Information
Safety Notices
FCC Statement
•• Do not use this product near water, for example, in a
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
•• Avoid using this product during an electrical storm.
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
•• Reorient or relocate the receiving antenna
•• Increase the separation between the equipment or
devices
•• Connect the equipment to an outlet other than the
receiver’s
•• Consult a dealer or an experienced radio/TV technician
for assistance
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator and your
body.
•• Caution: To reduce the risk of fire, use only No.26 AWG
or larger telecommunication line cord.
wet basement or near a swimming pool.
There may be a remote risk of electric shock from
lightning.
WARNING: This product contains lead, known
to the State of California to cause cancer, and
birth defects or other reproductive harm. Wash
hands after handling.
Industry Canada Statement
This Class B digital apparatus complies with Canadian
ICES-003 and RSS210.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device. This device has been designed to operate with
an antenna having a maximum gain of 2dBi. Antenna
having a higher gain is strictly prohibited per regulations
of Industry Canada. The required antenna impedance
is 50 ohms. To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen
that the EIRP is not more than required for successful
communication.
Industry Canada Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. IEEE
802.11b or 802.11g operation of this product in the USA is
firmware-limited to channels 1 through 11.
Wireless-G Access Point
27
Appendix D
Avis d’Industrie Canada
Cet appareil numérique de la classe B est conforme aux
normes NMB-003 et RSS210 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes :
1. il ne doit pas produire de brouillage et
2. il doit accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre
le fonctionnement du dispositif. Le dispositif a été
conçu pour fonctionner avec une antenne ayant un gain
maximum de 2 dBi. Les règlements d’Industrie Canada
interdisent strictement l’utilisation d’antennes dont le
gain est supérieur à cette limite. L’impédance requise
de l’antenne est de 50 ohms. Afin de réduire le risque d’interférence aux autres
utilisateurs, le type d’antenne et son gain doivent
être choisis de façon à ce que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne soit pas supérieure
au niveau requis pour obtenir une communication
satisfaisante.
Regulatory Information
Avis de non-responsabilité concernant les
appareils sans fil
Les performances maximales pour les réseaux sans fil
sont tirées des spécifications de la norme IEEE 802.11.
Les performances réelles peuvent varier, notamment
en fonction de la capacité du réseau sans fil, du débit
de la transmission de données, de la portée et de la
couverture. Les performances dépendent de facteurs,
conditions et variables multiples, en particulier de la
distance par rapport au point d’accès, du volume du trafic
réseau, des matériaux utilisés dans le bâtiment et du
type de construction, du système d’exploitation et de la
combinaison de produits sans fil utilisés, des interférences
et de toute autre condition défavorable.
Avis d’Industrie Canada concernant l’exposition
aux radiofréquences :
Ce matériel est conforme aux limites établies par IC
en matière d’exposition aux radiofréquences dans un
environnement non contrôlé. Ce matériel doit être installé
et utilisé à une distance d’au moins 20 cm entre l’antenne
et le corps de l’utilisateur.
L’émetteur ne doit pas être placé près d’une autre antenne
ou d’un autre émetteur, ou fonctionner avec une autre
antenne ou un autre émetteur.
Wireless Disclaimer
The maximum performance for wireless is derived from
IEEE Standard 802.11 specifications. Actual performance
can vary, including lower wireless network capacity,
data throughput rate, range and coverage. Performance
depends on many factors, conditions and variables,
including distance from the access point, volume of
network traffic, building materials and construction,
operating system used, mix of wireless products used,
interference and other adverse conditions.
Wireless-G Access Point
28
Appendix D
User Information for Consumer Products
Covered by EU Directive 2002/96/EC on
Waste Electric and Electronic Equipment
(WEEE)
This document contains important information for users
with regards to the proper disposal and recycling of
Linksys products. Consumers are required to comply with
this notice for all electronic products bearing the following
symbol:
Regulatory Information
Ceština (Czech) - Informace o ochraně životního
prostředí pro zákazníky v zemích Evropské unie
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené
tímto symbolem na produktu anebo na obalu bylo likvidováno
s netříděným komunálním odpadem. Tento symbol udává,
že daný produkt musí být likvidován odděleně od běžného
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu
a dalších elektrických a elektronických zařízení prostřednictvím
určených sběrných míst stanovených vládou nebo místními
úřady. Správná likvidace a recyklace pomáhá předcházet
potenciálním negativním dopadům na životní prostředí a lidské
zdraví. Podrobnější informace o likvidaci starého vybavení si
laskavě vyžádejte od místních úřadů, podniku zabývajícího se
likvidací komunálních odpadů nebo obchodu, kde jste produkt
zakoupili.
Dansk (Danish) - Miljøinformation for kunder i EU
English - Environmental Information for Customers in
the European Union
European Directive 2002/96/EC requires that the equipment
bearing this symbol on the product and/or its packaging must
not be disposed of with unsorted municipal waste. The symbol
indicates that this product should be disposed of separately
from regular household waste streams. It is your responsibility to
dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or
local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and
human health. For more detailed information about the disposal
of your old equipment, please contact your local authorities,
waste disposal service, or the shop where you purchased the
product.
Български (Bulgarian) - Информация относно
опазването на околната среда за потребители в
Европейския съюз
Европейска директива 2002/96/EC изисква уредите, носещи
този символ върху изделието и/или опаковката му, да не
се изхвърля т с несортирани битови отпадъци. Символът
обозначава, че изделието трябва да се изхвърля отделно от
сметосъбирането на обикновените битови отпадъци. Ваша
е отговорността този и другите електрически и електронни
уреди да се изхвърлят в предварително определени от
държавните или общински органи специализирани пунктове
за събиране. Правилното изхвърляне и рециклиране
ще спомогнат да се предотвратят евентуални вредни за
околната среда и здравето на населението последствия. За
по-подробна информация относно изхвърлянето на вашите
стари уреди се обърнете към местните власти, службите за
сметосъбиране или магазина, от който сте закупили уреда.
Wireless-G Access Point
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol
på produktet og/eller emballagen ikke må bortskaffes som
usorteret kommunalt affald. Symbolet betyder, at dette produkt
skal bortskaffes adskilt fra det almindelige husholdningsaffald.
Det er dit ansvar at bortskaffe dette og andet elektrisk og
elektronisk udstyr via bestemte indsamlingssteder udpeget
af staten eller de lokale myndigheder. Korrekt bortskaffelse
og genvinding vil hjælpe med til at undgå mulige skader for
miljøet og menneskers sundhed. Kontakt venligst de lokale
myndigheder, renovationstjenesten eller den butik, hvor du
har købt produktet, angående mere detaljeret information om
bortskaffelse af dit gamle udstyr.
Deutsch (German) - Umweltinformation für Kunden
innerhalb der Europäischen Union
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit
diesem Symbol versehen ist , nicht zusammen mit unsortiertem
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf
hin, dass das Produkt von regulärem Haushaltmüll getrennt
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses
Gerät und andere elektrische und elektronische Geräte über
die dafür zuständigen und von der Regierung oder örtlichen
Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
potentielle negative Folgen für Umwelt und die menschliche
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an
die örtlichen Behörden oder städtischen Entsorgungsdienste
oder an den Händler, bei dem Sie das Produkt erworben haben.
29
Appendix D
Regulatory Information
Eesti (Estonian) - Keskkonnaalane informatsioon
Euroopa Liidus asuvatele klientidele
Français (French) - Informations environnementales
pour les clients de l’Union européenne
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on
seadmeid, millel on tootel või pakendil käesolev sümbol ,
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike
ametiasutuste poolt ette nähtud kogumispunktide kaudu.
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste
tervisele. Vanade seadmete kõrvaldamise kohta täpsema
informatsiooni saamiseks võtke palun ühendust kohalike
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te
toote ostsite.
La directive européenne 2002/96/CE exige que l’équipement
sur lequel est apposé ce symbole sur le produit et/ou son
emballage ne soit pas jeté avec les autres ordures ménagères. Ce
symbole indique que le produit doit être éliminé dans un circuit
distinct de celui pour les déchets des ménages. Il est de votre
responsabilité de jeter ce matériel ainsi que tout autre matériel
électrique ou électronique par les moyens de collecte indiqués
par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme
ont pour but de lutter contre l’impact néfaste potentiel de ce
type de produits sur l’environnement et la santé publique. Pour
plus d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs publics
locaux, le service de traitement des déchets, ou l’endroit où vous
avez acheté le produit.
Español (Spanish) - Información medioambiental para
clientes de la Unión Europea
La Directiva 2002/96/CE de la UE exige que los equipos que
lleven este símbolo en el propio aparato y/o en su embalaje
no deben eliminarse junto con otros residuos urbanos no
seleccionados. El símbolo indica que el producto en cuestión
debe separarse de los residuos domésticos convencionales con
vistas a su eliminación. Es responsabilidad suya desechar este y
cualesquiera otros aparatos eléctricos y electrónicos a través de
los puntos de recogida que ponen a su disposición el gobierno y
las autoridades locales. Al desechar y reciclar correctamente estos
aparatos estará contribuyendo a evitar posibles consecuencias
negativas para el medio ambiente y la salud de las personas. Si
desea obtener información más detallada sobre la eliminación
segura de su aparato usado, consulte a las autoridades locales,
al servicio de recogida y eliminación de residuos de su zona o
pregunte en la tienda donde adquirió el producto.
ξλληνικά (Greek) - Στοιχεία περιβαλλοντικής
προστασίας για πελάτες εντός της Ευρωπαϊκής
Ένωσης
Η Κοινοτική Οδηγία 2002/96/EC απαιτεί ότι ο εξοπλισμός ο οποίος
φέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία
του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικά
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι
οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές.
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη
πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία.
Για περισσότερες πληροφορίες σχετικά με την απόρριψη του
παλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικές
αρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίο
αγοράσατε το προϊόν.
Wireless-G Access Point
Italiano (Italian) - Informazioni relative all’ambiente
per i clienti residenti nell’Unione Europea
La direttiva europea 2002/96/EC richiede che le apparecchiature
contrassegnate con questo simbolo
sul prodotto e/o
sull’imballaggio non siano smaltite insieme ai rifiuti urbani
non differenziati. Il simbolo indica che questo prodotto non
deve essere smaltito insieme ai normali rifiuti domestici. È
responsabilità del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante
le specifiche strutture di raccolta indicate dal governo o dagli
enti pubblici locali. Il corretto smaltimento ed il riciclaggio
aiuteranno a prevenire conseguenze potenzialmente negative
per l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli
enti pubblici di competenza, il servizio di smaltimento rifiuti o il
negozio nel quale avete acquistato il prodotto.
Latviešu valoda (Latvian) - Ekoloģiska informācija
klientiem Eiropas Savienības jurisdikcijā
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota
zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst
izmest nešķirotā veidā kopā ar komunālajiem atkritumiem
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē
to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar
parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo
un citas elektriskas un elektroniskas ierīces izmest atkritumos,
izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko
nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos
un pārstrāde tiek veikta pareizi, tad mazinās iespējamais
kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par
novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt
vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,
kur iegādājāties šo izstrādājumu.
30
Appendix D
Regulatory Information
Lietuvškai (Lithuanian) - Aplinkosaugos informacija,
skirta Europos Sąjungos vartotojams
Nederlands (Dutch) - Milieu-informatie voor klanten
in de Europese Unie
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),
negalima šalinti kartu su nerūšiuotomis komunalinėmis
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose
įsigijote tą gaminį.
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die
is voorzien van dit symbool op het product of de verpakking,
niet mag worden ingezameld met niet-gescheiden huishoudelijk
afval. Dit symbool geeft aan dat het product apart moet worden
ingezameld. U bent zelf verantwoordelijk voor de vernietiging
van deze en andere elektrische en elektronische apparatuur via de
daarvoor door de landelijke of plaatselijke overheid aangewezen
inzamelingskanalen. De juiste vernietiging en recycling van
deze apparatuur voorkomt mogelijke negatieve gevolgen voor
het milieu en de gezondheid. Voor meer informatie over het
vernietigen van uw oude apparatuur neemt u contact op met
de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de
winkel waar u het product hebt aangeschaft.
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti
fl-Unjoni Ewropea
Norsk (Norwegian) - Miljøinformasjon for kunder i EU
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih issimbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema
ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika
li dan il-prodott għandu jintrema separatament minn ma’ liskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew
il-ħanut minn fejn xtrajt il-prodott.
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol
avbildet på produktet og/eller pakningen, ikke må kastes
sammen med usortert avfall. Symbolet indikerer at dette
produktet skal håndteres atskilt fra ordinær avfallsinnsamling
for husholdningsavfall. Det er ditt ansvar å kvitte deg med
dette produktet og annet elektrisk og elektronisk avfall via egne
innsamlingsordninger slik myndighetene eller kommunene
bestemmer. Korrekt avfallshåndtering og gjenvinning vil
være med på å forhindre mulige negative konsekvenser for
miljø og helse. For nærmere informasjon om håndtering av
det kasserte utstyret ditt, kan du ta kontakt med kommunen,
en innsamlingsstasjon for avfall eller butikken der du kjøpte
produktet.
Magyar (Hungarian) - Környezetvédelmi információ az
európai uniós vásárlók számára
Polski (Polish) - Informacja dla klientów w Unii
Europejskiej o przepisach dotyczących ochrony
środowiska
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy
azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán
az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági
hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott
termék kidobásakor a szokványos háztartási hulladékelszállítási
rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön
felelõssége, hogy ezt, és más elektromos és elektronikus
berendezéseit a kormányzati vagy a helyi hatóságok által
kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ
hulladékfeldolgozás segít a környezetre és az emberi egészségre
potenciálisan ártalmas negatív hatások megelõzésében. Ha
elavult berendezéseinek felszámolásához további részletes
információra van szüksége, kérjük, lépjen kapcsolatba a helyi
hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal
üzlettel, ahol a terméket vásárolta.
Wireless-G Access Point
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt
oznaczony symbolem znajdującym się na produkcie i/lub jego
opakowaniu nie był wyrzucany razem z innymi niesortowanymi
odpadami komunalnymi. Symbol ten wskazuje, że produkt
nie powinien być usuwany razem ze zwykłymi odpadami z
gospodarstw domowych. Na Państwu spoczywa obowiązek
wyrzucania tego i innych urządzeń elektrycznych oraz
elektronicznych w punktach odbioru wyznaczonych przez władze
krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób
i jego recykling pomogą zapobiec potencjalnie negatywnym
konsekwencjom dla środowiska i zdrowia ludzkiego. W celu
uzyskania szczegółowych informacji o usuwaniu starego sprzętu,
prosimy zwrócić się do lokalnych władz, służb oczyszczania
miasta lub sklepu, w którym produkt został nabyty.
31
Appendix D
Regulatory Information
Português (Portuguese) - Informação ambiental para
clientes da União Europeia
Slovenčina (Slovene) - Okoljske informacije za stranke
v Evropski uniji
A Directiva Europeia 2002/96/CE exige que o equipamento
que exibe este símbolo no produto e/ou na sua embalagem
não seja eliminado junto com os resíduos municipais não
separados. O símbolo indica que este produto deve ser
eliminado separadamente dos resíduos domésticos regulares.
É da sua responsabilidade eliminar este e qualquer outro
equipamento eléctrico e electrónico através das instalações
de recolha designadas pelas autoridades governamentais ou
locais. A eliminação e reciclagem correctas ajudarão a prevenir
as consequências negativas para o ambiente e para a saúde
humana. Para obter informações mais detalhadas sobre a
forma de eliminar o seu equipamento antigo, contacte as
autoridades locais, os serviços de eliminação de resíduos ou o
estabelecimento comercial onde adquiriu o produto.
Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme,
označene s tem simbolom – na izdelku in/ali na embalaži – med
običajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba
izdelek odvreči ločeno od preostalih gospodinjskih odpadkov.
Vaša odgovornost je, da to in preostalo električno in elektronsko
opremo odnesete na posebna zbirališča, ki jih določijo
državne ustanove ali lokalna uprava. S pravilnim odlaganjem
in recikliranjem boste preprečili morebitne škodljive vplive na
okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare
opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer
ste izdelek kupili.
Română (Romanian) - Informaţii de mediu pentru
clienţii din Uniunea Europeană
Directiva europeană 2002/96/CE impune ca echipamentele care
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să
nu fie casate împreună cu gunoiul menajer municipal. Simbolul
indică faptul că acest produs trebuie să fie casat separat de
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi
acest produs şi alte echipamente electrice şi electronice prin
intermediul unităţilor de colectare special desemnate de guvern
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta
la prevenirea potenţialelor consecinţe negative asupra sănătăţii
mediului şi a oamenilor. Pentru mai multe informaţii detaliate
cu privire la casarea acestui echipament vechi, contactaţi
autorităţile locale, serviciul de salubrizare sau magazinul de la
care aţi achiziţionat produsul.
Slovenčina (Slovak) - Informácie o ochrane životného
prostredia pre zákazníkov v Európskej únii
Podľa európskej smernice 2002/96/ES zariadenie s týmto
symbolom
na produkte a/alebo jeho balení nesmie byť
likvidované spolu s netriedeným komunálnym odpadom.
Symbol znamená, že produkt by sa mal likvidovať oddelene
od bežného odpadu z domácností. Je vašou povinnosťou
likvidovať toto i ostatné elektrické a elektronické zariadenia
prostredníctvom špecializovaných zberných zariadení určených
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia
pomôže zabrániť prípadným negatívnym dopadom na životné
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov
alebo obchod, v ktorom ste si produkt zakúpili.
Wireless-G Access Point
Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä
symboli
itse tuotteessa ja/tai sen pakkauksessa, laitteistoa
ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään
tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää
tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet
viemällä tuote tai tuotteet viranomaisten määräämään
keräyspisteeseen. Laitteiston oikea hävittäminen estää
mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten
terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta
saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä
myymälästä, josta ostit tuotteen.
Svenska (Swedish) - Miljöinformation för kunder i
Europeiska unionen
Det europeiska direktivet 2002/96/EC kräver att utrustning med
denna symbol på produkten och/eller förpackningen inte får
kastas med osorterat kommunalt avfall. Symbolen visar att denna
produkt bör kastas efter att den avskiljts från vanligt hushållsavfall.
Det faller på ditt ansvar att kasta denna och annan elektrisk och
elektronisk utrustning på fastställda insamlingsplatser utsedda
av regeringen eller lokala myndigheter. Korrekt kassering och
återvinning skyddar mot eventuella negativa konsekvenser
för miljön och personhälsa. För mer detaljerad information om
kassering av din gamla utrustning kontaktar du dina lokala
myndigheter, avfallshanteringen eller butiken där du köpte
produkten.
WEB: For additional information, please visit
www.linksys.com
32
Appendix E
Appendix E: Software
License Agreement
Software in Linksys Products
This product from Cisco-Linksys LLC or from one of its
affiliates Cisco Systems-Linksys (Asia) Pte Ltd. or CiscoLinksys K.K. (“Linksys”) contains software (including
firmware) originating from Linksys and its suppliers
and may also contain software from the open source
community. Any software originating from Linksys and its
suppliers is licensed under the Linksys Software License
Agreement contained at Schedule 1 below. You may also
be prompted to review and accept that Linksys Software
License Agreement upon installation of the software
Any software from the open source community is licensed
under the specific license terms applicable to that software
made available by Linksys at www.linksys.com/gpl or as
provided for in Schedules 2, 3 and 4 below.
Where such specific license terms entitle you to the source
code of such software, that source code is upon request
available at cost from Linksys for at least three years
from the purchase date of this product and may also be
available for download from www.linksys.com/gpl. For
detailed license terms and additional information on
open source software in Linksys products please look at
the Linksys public web site at: www.linksys.com/gpl/ or
Schedules 2, 3 or 4 below as applicable.
BY DOWNLOADING OR INSTALLING THE SOFTWARE,
OR USING THE PRODUCT CONTAINING THE SOFTWARE,
YOU ARE CONSENTING TO BE BOUND BY THE SOFTWARE
LICENSE AGREEMENTS BELOW. IF YOU DO NOT AGREE TO
ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD,
INSTALL OR USE THE SOFTWARE. YOU MAY RETURN
UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED
AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT)
FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL
PURCHASE, SUBJECT TO THE RETURN PROCESS AND
POLICIES OF THE PARTY FROM WHICH YOU PURCHASED
SUCH PRODUCT OR SOFTWARE.
Software Licenses
The software Licenses applicable to software from Linksys
are made available at the Linksys public web site at:
www.linksys.com. For your convenience of reference, a
copy of the Linksys Software License Agreement and the
main open source code licenses used by Linksys in its
products are contained in the Schedules below.
Wireless-G Access Point
Software License Agreement
Schedule 1 - Linksys Software License Agreement
THIS LICENSE AGREEMENT IS BETWEEN YOU AND
CISCO-LINKSYS LLC OR ONE OF ITS AFFILIATES CISCO
SYSTEMS-LINKSYS (ASIA) PTE LTD. OR CISCO-LINKSYS
K.K. (“LINKSYS”) LICENSING THE SOFTWARE INSTEAD OF
CISCO-LINKSYS LLC. BY DOWNLOADING OR INSTALLING
THE SOFTWARE, OR USING THE PRODUCT CONTAINING
THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY
THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THESE
TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE
THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE
(OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER
PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND
UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO
THE RETURN PROCESS AND POLICIES OF THE PARTY FROM
WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.
License. Subject to the terms and conditions of this
Agreement, Linksys grants the original end user purchaser
of the Linksys product containing the Software (“You”)
a nonexclusive license to use the Software solely as
embedded in or (where authorized in the applicable
documentation) for communication with such product.
This license may not be sublicensed, and is not transferable
except to a person or entity to which you transfer
ownership of the complete Linksys product containing
the Software, provided you permanently transfer all rights
under this Agreement and do not retain any full or partial
copies of the Software, and the recipient agrees to the
terms of this Agreement.
“Software” includes, and this Agreement will apply to
(a) the software of Linksys or its suppliers provided in or
with the applicable Linksys product, excluding technology
from the open source community, and (b) any upgrades,
updates, bug fixes or modified versions (“Upgrades”) or
backup copies of the Software supplied to You by Linksys
or an authorized reseller, provided you already hold a
valid license to the original software and have paid any
applicable fee for the Upgrade.
Protection of Information. The Software and
documentation contain trade secrets and/or copyrighted
materials of Linksys or its suppliers. You will not copy
or modify the Software or decompile, decrypt, reverse
engineer or disassemble the Software (except to the
extent expressly permitted by law notwithstanding this
provision), and You will not disclose or make available
such trade secrets or copyrighted material in any form
to any third party. Title to and ownership of the Software
and documentation and any portion thereof, will remain
solely with Linksys or its suppliers.
Collection and Processing of Information. You agree that
Linksys and/or its affiliates may, from time to time, collect
and process information about your Linksys product and/
or the Software and/or your use of either in order (i) to
enable Linksys to offer you Upgrades; (ii) to ensure that
33
Software License Agreement
Appendix E
your Linksys product and/or the Software is being used in
accordance with the terms of this Agreement; (iii) to provide
improvements to the way Linksys delivers technology to
you and to other Linksys customers; (iv) to enable Linksys
to comply with the terms of any agreements it has with
any third parties regarding your Linksys product and/or
Software and/or (v) to enable Linksys to comply with all
applicable laws and/or regulations, or the requirements
of any regulatory authority or government agency.
Linksys and/ or its affiliates may collect and process
this information provided that it does not identify you
personally. Your use of your Linksys product and/or the
Software constitutes this consent by you to Linksys and/
or its affiliates’ collection and use of such information and,
for EEA customers, to the transfer of such information to a
location outside the EEA.
Software Upgrades etc. If the Software enables you to
receive Upgrades, you may elect at any time to receive
these Upgrades either automatically or manually. If you
elect to receive Upgrades manually or you otherwise
elect not to receive or be notified of any Upgrades, you
may expose your Linksys product and/or the Software
to serious security threats and/or some features within
your Linksys product and/or Software may become
inaccessible. There may be circumstances where we
apply an Upgrade automatically in order to comply with
changes in legislation, legal or regulatory requirements
or as a result of requirements to comply with the terms
of any agreements Linksys has with any third parties
regarding your Linksys product and/or the Software. You
will always be notified of any Upgrades being delivered
to you. The terms of this license will apply to any such
Upgrade unless the Upgrade in question is accompanied
by a separate license, in which event the terms of that
license will apply.
Open Source Software. The GPL or other open source
code incorporated into the Software and the open source
license for such source code are available for free download
at http://www.linksys.com/gpl. If You would like a copy
of the GPL or other open source code in this Software on a
CD, Linksys will mail to You a CD with such code for $9.99
plus the cost of shipping, upon request.
Term and Termination. You may terminate this License
at any time by destroying all copies of the Software
and documentation. Your rights under this License will
terminate immediately without notice from Linksys if You
fail to comply with any provision of this Agreement.
Limited Warranty. The warranty terms and period
specified in the applicable Linksys Product User Guide
shall also apply to the Software.
Disclaimer of Liabilities. IN NO EVENT WILL LINKSYS OR
ITS SUPPLIERS BE LIABLE FOR ANY LOST DATA, REVENUE
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF
CAUSE (INCLUDING NEGLIGENCE), ARISING OUT OF
Wireless-G Access Point
OR RELATED TO THE USE OF OR INABILITY TO USE THE
SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL
LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU
FOR THE PRODUCT. The foregoing limitations will apply
even if any warranty or remedy under this Agreement fails
of its essential purpose. Some jurisdictions do not allow
the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not
apply to You.
Export. Software, including technical data, may be subject
to U.S. export control laws and regulations and/or export
or import regulations in other countries. You agree to
comply strictly with all such laws and regulations.
U.S. Government Users. The Software and documentation
qualify as “commercial items” as defined at 48 C.F.R. 2.101
and 48 C.F.R. 12.212. All Government users acquire the
Software and documentation with only those rights
herein that apply to non-governmental customers.
General Terms. This Agreement will be governed by and
construed in accordance with the laws of the State of
California, without reference to conflict of laws principles.
The United Nations Convention on Contracts for the
International Sale of Goods will not apply. If any portion
of this Agreement is found to be void or unenforceable,
the remaining provisions will remain in full force and
effect. This Agreement constitutes the entire agreement
between the parties with respect to the Software and
supersedes any conflicting or additional terms contained
in any purchase order or elsewhere.
END OF SCHEDULE 1
Schedule 2
If this Linksys product contains open source software
licensed under Version 2 of the “GNU General Public
License” then the license terms below in this Schedule 2
will apply to that open source software. The license terms
below in this Schedule 2 are from the public web site at
http://www.gnu.org/copyleft/gpl.html
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright © 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
USA
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the
34
Appendix E
GNU General Public License is intended to guarantee your
freedom to share and change free software–to make sure
the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s
software and to any other program whose authors
commit to using it. (Some other Free Software Foundation
software is covered by the GNU Lesser General Public
License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to
freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to
distribute copies of free software (and charge for this
service if you wish), that you receive source code or can
get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know
you can do these things.
To protect your rights, we need to make restrictions that
forbid anyone to deny you these rights or to ask you to
surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the
software, or if you modify it.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must give the recipients
all the rights that you have. You must make sure that they,
too, receive or can get the source code. And you must
show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the
software, and (2) offer you this license which gives you
legal permission to copy, distribute and/or modify the
software.
Also, for each author’s protection and ours, we want to
make certain that everyone understands that there is no
warranty for this free software. If the software is modified
by someone else and passed on, we want its recipients
to know that what they have is not the original, so that
any problems introduced by others will not reflect on the
original authors’ reputations.
Finally, any free program is threatened constantly by
software patents. We wish to avoid the danger that
redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary.
To prevent this, we have made it clear that any patent must
be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution
and modification follow.
Wireless-G Access Point
Software License Agreement
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License applies to any program or other work
which contains a notice placed by the copyright
holder saying it may be distributed under the terms
of this General Public License. The “Program”, below,
refers to any such program or work, and a “work
based on the Program” means either the Program
or any derivative work under copyright law: that is
to say, a work containing the Program or a portion
of it, either verbatim or with modifications and/
or translated into another language. (Hereinafter,
translation is included without limitation in the term
“modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and
modification are not covered by this License; they
are outside its scope. The act of running the Program
is not restricted, and the output from the Program is
covered only if its contents constitute a work based on
the Program (independent of having been made by
running the Program). Whether that is true depends
on what the Program does.
1. You may copy and distribute verbatim copies of the
Program’s source code as you receive it, in any medium,
provided that you conspicuously and appropriately
publish on each copy an appropriate copyright
notice and disclaimer of warranty; keep intact all the
notices that refer to this License and to the absence
of any warranty; and give any other recipients of the
Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Program
or any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications
or work under the terms of Section 1 above, provided
that you also meet all of these conditions:
a. You must cause the modified files to carry
prominent notices stating that you changed the
files and the date of any change.
b. You must cause any work that you distribute or
publish, that in whole or in part contains or is
derived from the Program or any part thereof, to be
licensed as a whole at no charge to all third parties
under the terms of this License.
35
Appendix E
c. If the modified program normally reads commands
interactively when run, you must cause it, when
started running for such interactive use in the most
ordinary way, to print or display an announcement
including an appropriate copyright notice and
a notice that there is no warranty (or else, saying
that you provide a warranty) and that users may
redistribute the program under these conditions,
and telling the user how to view a copy of
this License. (Exception: if the Program itself is
interactive but does not normally print such an
announcement, your work based on the Program
is not required to print an announcement.)
These requirements apply to the modified work as
a whole. If identifiable sections of that work are not
derived from the Program, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do not
apply to those sections when you distribute them as
separate works. But when you distribute the same
sections as part of a whole which is a work based on
the Program, the distribution of the whole must be on
the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights
or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on
the Program.
In addition, mere aggregation of another work not
based on the Program with the Program (or with a
work based on the Program) on a volume of a storage
or distribution medium does not bring the other work
under the scope of this License.
3. You may copy and distribute the Program (or a
work based on it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
above provided that you also do one of the following:
a. Accompany it with the complete corresponding
machine-readable source code, which must be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange; or,
b. Accompany it with a written offer, valid for at least
three years, to give any third party, for a charge
no more than your cost of physically performing
source distribution, a complete machine-readable
copy of the corresponding source code, to be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange; or,
Wireless-G Access Point
Software License Agreement
c. Accompany it with the information you received as
to the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial
distribution and only if you received the program
in object code or executable form with such an
offer, in accord with Subsection b above.)
The source code for a work means the preferred form
of the work for making modifications to it. For an
executable work, complete source code means all
the source code for all modules it contains, plus any
associated interface definition files, plus the scripts
used to control compilation and installation of the
executable. However, as a special exception, the source
code distributed need not include anything that is
normally distributed (in either source or binary form)
with the major components (compiler, kernel, and so
on) of the operating system on which the executable
runs, unless that component itself accompanies the
executable.
If distribution of executable or object code is made
by offering access to copy from a designated place,
then offering equivalent access to copy the source
code from the same place counts as distribution of
the source code, even though third parties are not
compelled to copy the source along with the object
code.
4. You may not copy, modify, sublicense, or distribute
the Program except as expressly provided under
this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will
automatically terminate your rights under this License.
However, parties who have received copies, or rights,
from you under this License will not have their licenses
terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Program or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based
on it.
6. Each time you redistribute the Program (or any work
based on the Program), the recipient automatically
receives a license from the original licensor to copy,
distribute or modify the Program subject to these
terms and conditions. You may not impose any further
restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing
compliance by third parties to this License.
36
Software License Agreement
Appendix E
7. If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do
not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other
pertinent obligations, then as a consequence you
may not distribute the Program at all. For example,
if a patent license would not permit royalty-free
redistribution of the Program by all those who receive
copies directly or indirectly through you, then the only
way you could satisfy both it and this License would be
to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply and
the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system, which is implemented
by public license practices. Many people have
made generous contributions to the wide range of
software distributed through that system in reliance
on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear
what is believed to be a consequence of the rest of this
License.
8. If the distribution and/or use of the Program is
restricted in certain countries either by patents or by
copyrighted interfaces, the original copyright holder
who places the Program under this License may add an
explicit geographical distribution limitation excluding
those countries, so that distribution is permitted only
in or among countries not thus excluded. In such case,
this License incorporates the limitation as if written in
the body of this License.
9. The Free Software Foundation may publish revised
and/or new versions of the General Public License
from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number.
If the Program specifies a version number of this
License which applies to it and “any later version”, you
have the option of following the terms and conditions
either of that version or of any later version published
by the Free Software Foundation. If the Program does
Wireless-G Access Point
not specify a version number of this License, you
may choose any version ever published by the Free
Software Foundation.
10.If you wish to incorporate parts of the Program into
other free programs whose distribution conditions are
different, write to the author to ask for permission. For
software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will
be guided by the two goals of preserving the free status
of all derivatives of our free software and of promoting
the sharing and reuse of software generally.
NO WARRANTY
11.BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE,
BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR
A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
END OF TERMS AND CONDITIONS
END OF SCHEDULE 2
Schedule 3
If this Linksys product contains open source software
licensed under Version 2.1 of the“GNU Lesser General Public
License” then the license terms below in this Schedule 3
will apply to that open source software. The license terms
below in this Schedule 3 are from the public web site at
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html.
37
Appendix E
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
USA
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It also
counts as the successor of the GNU Library Public License,
version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your
freedom to share and change free software—to make
sure the software is free for all its users.
This license, the Lesser General Public License, applies to
some specially designated software packages—typically
libraries—of the Free Software Foundation and other
authors who decide to use it. You can use it too, but we
suggest you first think carefully about whether this license
or the ordinary General Public License is the better strategy
to use in any particular case, based on the explanations
below.
When we speak of free software, we are referring to
freedom of use, not price. Our General Public Licenses
are designed to make sure that you have the freedom
to distribute copies of free software (and charge for this
service if you wish); that you receive source code or can
get it if you want it; that you can change the software and
use pieces of it in new free programs; and that you are
informed that you can do these things.
To protect your rights, we need to make restrictions that
forbid distributors to deny you these rights or to ask you
to surrender these rights. These restrictions translate to
certain responsibilities for you if you distribute copies of
the library or if you modify it.
For example, if you distribute copies of the library,
whether gratis or for a fee, you must give the recipients
all the rights that we gave you. You must make sure that
they, too, receive or can get the source code. If you link
other code with the library, you must provide complete
object files to the recipients, so that they can relink them
with the library after making changes to the library and
recompiling it. And you must show them these terms so
they know their rights.
We protect your rights with a two-step method: (1) we
copyright the library, and (2) we offer you this license,
which gives you legal permission to copy, distribute and/
or modify the library.
Wireless-G Access Point
Software License Agreement
To protect each distributor, we want to make it very clear
that there is no warranty for the free library. Also, if the
library is modified by someone else and passed on, the
recipients should know that what they have is not the
original version, so that the original author’s reputation
will not be affected by problems that might be introduced
by others.
Finally, software patents pose a constant threat to the
existence of any free program. We wish to make sure
that a company cannot effectively restrict the users of
a free program by obtaining a restrictive license from a
patent holder. Therefore, we insist that any patent license
obtained for a version of the library must be consistent
with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered
by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain
designated libraries, and is quite different from the
ordinary General Public License. We use this license for
certain libraries in order to permit linking those libraries
into non-free programs.
When a program is linked with a library, whether
statically or using a shared library, the combination of
the two is legally speaking a combined work, a derivative
of the original library. The ordinary General Public
License therefore permits such linking only if the entire
combination fits its criteria of freedom. The Lesser General
Public License permits more lax criteria for linking other
code with the library.
We call this license the “Lesser” General Public License
because it does Less to protect the user’s freedom than
the ordinary General Public License. It also provides
other free software developers Less of an advantage over
competing non-free programs. These disadvantages are
the reason we use the ordinary General Public License
for many libraries. However, the Lesser license provides
advantages in certain special circumstances.
For example, on rare occasions, there may be a special
need to encourage the widest possible use of a certain
library, so that it becomes a de-facto standard. To achieve
this, non-free programs must be allowed to use the library.
A more frequent case is that a free library does the same
job as widely used non-free libraries. In this case, there is
little to gain by limiting the free library to free software
only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use
a large body of free software. For example, permission to
use the GNU C Library in non-free programs enables many
more people to use the whole GNU operating system, as
well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less
protective of the users’ freedom, it does ensure that the
user of a program that is linked with the Library has the
38
Appendix E
freedom and the wherewithal to run that program using a
modified version of the Library.
The precise terms and conditions for copying, distribution
and modification follow. Pay close attention to the
difference between a “work based on the library” and a
“work that uses the library”. The former contains code
derived from the library, whereas the latter must be
combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License Agreement applies to any software library
or other program which contains a notice placed by
the copyright holder or other authorized party saying
it may be distributed under the terms of this Lesser
General Public License (also called “this License”). Each
licensee is addressed as “you”.
A “library” means a collection of software functions
and/or data prepared so as to be conveniently linked
with application programs (which use some of those
functions and data) to form executables.
The “Library”, below, refers to any such software library
or work which has been distributed under these terms.
A “work based on the Library” means either the Library
or any derivative work under copyright law: that is to
say, a work containing the Library or a portion of it,
either verbatim or with modifications and/or translated
straightforwardly into another language. (Hereinafter,
translation is included without limitation in the term
“modification”.)
“Source code” for a work means the preferred form of
the work for making modifications to it. For a library,
complete source code means all the source code for
all modules it contains, plus any associated interface
definition files, plus the scripts used to control
compilation and installation of the library.
Activities other than copying, distribution and
modification are not covered by this License; they are
outside its scope. The act of running a program using
the Library is not restricted, and output from such a
program is covered only if its contents constitute a
work based on the Library (independent of the use
of the Library in a tool for writing it). Whether that is
true depends on what the Library does and what the
program that uses the Library does.
Wireless-G Access Point
Software License Agreement
1. You may copy and distribute verbatim copies of the
Library’s complete source code as you receive it, in
any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this License and to
the absence of any warranty; and distribute a copy of
this License along with the Library.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Library or
any portion of it, thus forming a work based on the
Library, and copy and distribute such modifications
or work under the terms of Section 1 above, provided
that you also meet all of these conditions:
a) The modified work must itself be a software
library.
b) You must cause the files modified to carry
prominent notices stating that you changed the
files and the date of any change.
c) You must cause the whole of the work to be
licensed at no charge to all third parties under the
terms of this License.
d) If a facility in the modified Library refers to a function
or a table of data to be supplied by an application
program that uses the facility, other than as an
argument passed when the facility is invoked, then
you must make a good faith effort to ensure that,
in the event an application does not supply such
function or table, the facility still operates, and
performs whatever part of its purpose remains
meaningful.
(For example, a function in a library to compute
square roots has a purpose that is entirely welldefined independent of the application. Therefore,
Subsection 2d requires that any applicationsupplied function or table used by this function
must be optional: if the application does not supply
it, the square root function must still compute
square roots.)
These requirements apply to the modified work as
a whole. If identifiable sections of that work are not
derived from the Library, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do
not apply to those sections when you distribute
them as separate works. But when you distribute
the same sections as part of a whole which is a
work based on the Library, the distribution of the
whole must be on the terms of this License, whose
permissions for other licensees extend to the entire
whole, and thus to each and every part regardless
of who wrote it.
39
Appendix E
Thus, it is not the intent of this section to claim
rights or contest your rights to work written entirely
by you; rather, the intent is to exercise the right to
control the distribution of derivative or collective
works based on the Library.
In addition, mere aggregation of another work
not based on the Library with the Library (or with
a work based on the Library) on a volume of a
storage or distribution medium does not bring the
other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a
given copy of the Library. To do this, you must alter all
the notices that refer to this License, so that they refer
to the ordinary GNU General Public License, version
2, instead of to this License. (If a newer version than
version 2 of the ordinary GNU General Public License
has appeared, then you can specify that version
instead if you wish.) Do not make any other change in
these notices.
Once this change is made in a given copy, it is
irreversible for that copy, so the ordinary GNU General
Public License applies to all subsequent copies and
derivative works made from that copy.
This option is useful when you wish to copy part of the
code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion
or derivative of it, under Section 2) in object code or
executable form under the terms of Sections 1 and
2 above provided that you accompany it with the
complete corresponding machine-readable source
code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used
for software interchange.
If distribution of object code is made by offering
access to copy from a designated place, then offering
equivalent access to copy the source code from the
same place satisfies the requirement to distribute
the source code, even though third parties are not
compelled to copy the source along with the object
code.
5. A program that contains no derivative of any portion
of the Library, but is designed to work with the Library
by being compiled or linked with it, is called a “work
that uses the Library”. Such a work, in isolation, is not
a derivative work of the Library, and therefore falls
outside the scope of this License.
However, linking a “work that uses the Library” with
the Library creates an executable that is a derivative
of the Library (because it contains portions of the
Library), rather than a “work that uses the library”. The
executable is therefore covered by this License. Section
6 states terms for distribution of such executables.
Wireless-G Access Point
Software License Agreement
When a “work that uses the Library” uses material from
a header file that is part of the Library, the object code
for the work may be a derivative work of the Library
even though the source code is not. Whether this is
true is especially significant if the work can be linked
without the Library, or if the work is itself a library. The
threshold for this to be true is not precisely defined by
law.
If such an object file uses only numerical parameters,
data structure layouts and accessors, and small macros
and small inline functions (ten lines or less in length),
then the use of the object file is unrestricted, regardless
of whether it is legally a derivative work. (Executables
containing this object code plus portions of the Library
will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you
may distribute the object code for the work under the
terms of Section 6. Any executables containing that
work also fall under Section 6, whether or not they are
linked directly with the Library itself.
6. As an exception to the Sections above, you may also
combine or link a “work that uses the Library” with the
Library to produce a work containing portions of the
Library, and distribute that work under terms of your
choice, provided that the terms permit modification
of the work for the customer’s own use and reverse
engineering for debugging such modifications.
You must give prominent notice with each copy of
the work that the Library is used in it and that the
Library and its use are covered by this License. You
must supply a copy of this License. If the work during
execution displays copyright notices, you must include
the copyright notice for the Library among them, as
well as a reference directing the user to the copy of this
License. Also, you must do one of these things:
a) Accompany the work with the complete
corresponding machine-readable source code
for the Library including whatever changes were
used in the work (which must be distributed
under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the
complete machine-readable “work that uses the
Library”, as object code and/or source code, so that
the user can modify the Library and then relink
to produce a modified executable containing the
modified Library. (It is understood that the user
who changes the contents of definitions files in the
Library will not necessarily be able to recompile the
application to use the modified definitions.)
40
Appendix E
Software License Agreement
b) Use a suitable shared library mechanism for linking
with the Library. A suitable mechanism is one that
(1) uses at run time a copy of the library already
present on the user’s computer system, rather than
copying library functions into the executable, and
(2) will operate properly with a modified version of
the library, if the user installs one, as long as the
modified version is interface-compatible with the
version that the work was made with.
8. You may not copy, modify, sublicense, link with, or
distribute the Library except as expressly provided
under this License. Any attempt otherwise to copy,
modify, sublicense, link with, or distribute the Library
is void, and will automatically terminate your rights
under this License. However, parties who have received
copies, or rights, from you under this License will not
have their licenses terminated so long as such parties
remain in full compliance.
c) Accompany the work with a written offer, valid
for at least three years, to give the same user the
materials specified in Subsection 6a, above, for a
charge no more than the cost of performing this
distribution.
9. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Library or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Library (or any work based on the
Library), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying,
distributing or modifying the Library or works based
on it.
d) If distribution of the work is made by offering access
to copy from a designated place, offer equivalent
access to copy the above specified materials from
the same place.
e) Verify that the user has already received a copy of
these materials or that you have already sent this
user a copy.
For an executable, the required form of the “work that
uses the Library” must include any data and utility
programs needed for reproducing the executable from
it. However, as a special exception, the materials to be
distributed need not include anything that is normally
distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless
that component itself accompanies the executable.
It may happen that this requirement contradicts the
license restrictions of other proprietary libraries that
do not normally accompany the operating system.
Such a contradiction means you cannot use both
them and the Library together in an executable that
you distribute.
7. You may place library facilities that are a work based
on the Library side-by-side in a single library together
with other library facilities not covered by this License,
and distribute such a combined library, provided that
the separate distribution of the work based on the
Library and of the other library facilities is otherwise
permitted, and provided that you do these two
things:
a) Accompany the combined library with a copy of the
same work based on the Library, uncombined with
any other library facilities. This must be distributed
under the terms of the Sections above.
b) Give prominent notice with the combined library of
the fact that part of it is a work based on the Library,
and explaining where to find the accompanying
uncombined form of the same work.
Wireless-G Access Point
10.Each time you redistribute the Library (or any work
based on the Library), the recipient automatically
receives a license from the original licensor to copy,
distribute, link with or modify the Library subject
to these terms and conditions. You may not impose
any further restrictions on the recipients’ exercise of
the rights granted herein. You are not responsible
for enforcing compliance by third parties with this
License.
11.If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do
not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other
pertinent obligations, then as a consequence you may
not distribute the Library at all. For example, if a patent
license would not permit royalty-free redistribution of
the Library by all those who receive copies directly or
indirectly through you, then the only way you could
satisfy both it and this License would be to refrain
entirely from distribution of the Library.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply, and
the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system which is implemented
by public license practices. Many people have
made generous contributions to the wide range of
41
Software License Agreement
Appendix E
software distributed through that system in reliance
on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear
what is believed to be a consequence of the rest of this
License.
12.If the distribution and/or use of the Library is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Library under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the
body of this License.
13.The Free Software Foundation may publish revised
and/or new versions of the Lesser General Public
License from time to time. Such new versions will be
similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Library specifies a version number of this License
which applies to it and “any later version”, you have the
option of following the terms and conditions either of
that version or of any later version published by the Free
Software Foundation. If the Library does not specify a
license version number, you may choose any version
ever published by the Free Software Foundation.
15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE LIBRARY, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD
THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW
OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE LIBRARY (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY
TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
END OF SCHEDULE 3
14.If you wish to incorporate parts of the Library into
other free programs whose distribution conditions are
incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for
this. Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of
software generally.
Schedule 4
NO WARRANTY
This product includes software written by Tim Hudson
(tjh@cryptsoft.com).
If this Linksys product contains open source software
licensed under the OpenSSL license:
This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/).
This product includes cryptographic software written by
Eric Young (eay@cryptsoft.com).
In addition, if this Linksys product contains open
source software licensed under the OpenSSL license
then the license terms below in this Schedule 3 will
apply to that open source software. The license terms
below in this Schedule 3 are from the public web site at
http://www.openssl.org/source/license.html.
The OpenSSL toolkit stays under a dual license, i.e. both
the conditions of the OpenSSL License and the original
SSLeay license apply to the toolkit. See below for the
actual license texts. Actually both licenses are BSD-style
Open Source licenses. In case of any license issues related
to OpenSSL please contact openssl-core@openssl.org.
Wireless-G Access Point
42
Appendix E
Software License Agreement
OpenSSL License
Original SSLeay License
Copyright © 1998-2007 The OpenSSL Project. All rights
reserved.
Copyright © 1995-1998 Eric Young (eay@cryptsoft.com)All
rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
This package is an SSL implementation written by Eric
Young (eay@cryptsoft.com).
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgment: “This product includes software
developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project”
must not be used to endorse or promote products
derived from this software without prior written
permission. For written permission, please contact
openssl-core@openssl.org.
5. Products derived from this software may not be called
“OpenSSL” nor may “OpenSSL” appear in their names
without prior written permission of the OpenSSL
Project.
6. Redistributions of any form whatsoever must retain
the following acknowledgment: “This product includes
software developed by the OpenSSL Project for use in
the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT
“AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
This product includes cryptographic software written by
Eric Young (eay@cryptsoft.com). This product includes
software written by Tim Hudson (tjh@cryptsoft.com).
Wireless-G Access Point
The implementation was written so as to conform with
Netscape’s SSL.
This library is free for commercial and non-commercial
use as long as the following conditions are adhered to.
The following conditions apply to all code found in this
distribution, be it the RC4, RSA, lhash, DES, etc., code; not
just the SSL code. The SSL documentation included with
this distribution is covered by the same copyright terms
except that the holder is Tim Hudson (tjh@cryptsoft.
com).
Copyright remains Eric Young’s, and as such any Copyright
notices in the code are not to be removed.
If this package is used in a product, Eric Young should be
given attribution as the author of the parts of the library
used. This can be in the form of a textual message at
program startup or in documentation (online or textual)
provided with the package.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgement:
“This product includes cryptographic software written
by Eric Young (eay@cryptsoft.com)”
The word ‘cryptographic’ can be left out if the routines
from the library being used are not cryptographic
related.
4. If you include any Windows specific code (or a derivative
thereof ) from the apps directory (application code)
you must include an acknowledgement: “This product
includes software written by Tim Hudson (tjh@
cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
43
Appendix E
Software License Agreement
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The license and distribution terms for any publicly available
version or derivative of this code cannot be changed. i.e.
this code cannot simply be copied and put under another
distribution license [including the GNU Public License.]
END OF SCHEDULE 4
8092230A-AI
Wireless-G Access Point
44
Download PDF

advertising