dm-rmc-100
DM-RMC-100-1
DigitalMedia™ Room Controller & DM CAT Receiver
The DM-RMC-100-1 provides a convenient one-box interface solution to
support a single display device as part of a complete DigitalMedia
system. It functions as a DM CAT receiver and control interface,
providing a single HDMI® output along with a variety of control ports.
Its compact, low-profile design allows the DM-RMC-100-1 to be
installed discreetly behind a flat panel display or above a ceiling
mounted projector.
DigitalMedia™
As the leader in HDMI and control system technologies, Crestron® has
developed DigitalMedia, the first complete HD AV distribution system
that takes HDMI to a higher level, and allows virtually any mix of AV
sources to be distributed throughout the home, office, school, or
virtually any other facility.
DigitalMedia distributes uncompressed digital video and audio signals
up to 450 feet (137 m) using DM cable[1]. DigitalMedia thoughtfully
manages all of the different signals and devices, matching each
source's output to the capabilities of the selected display(s) without
using scaling or compression. Every signal is preserved in its native
video resolution and audio format, ensuring a pure, lossless signal
path throughout.
Multimedia Display Interface
A single HDMI digital AV output port is provided on the DM-RMC-100-1,
supporting HDMI with HDCP, Deep Color and 3D, handling WUXGA computer
resolutions and 1080p60 HDTV with multi-channel HD lossless
audio—all through a single connection. The HDMI output can also
handle DVI signals using an appropriate adapter or interface
cable[2]. In addition, there are RS-232, IR, and Ethernet control
ports provided for controlling the display device, plus two relays for
screen and lift control, and a SENS input for connection of an
optional current sensor or contact closure.
Multiple DM-RMC-100-1s may be installed to handle each display in a
multi-room distribution system, all fed from a central DM-MD series
switcher. Or, a single DM-RMC-100-1 can be fed straight from a
DM-TX-100 or other DM CAT transmitter to provide a simple solution for
extending a computer or AV signal to feed a single display. The
connection to the switcher or transmitter requires just one
DigitalMedia cable, with a potential cable length up to 450 feet[1].
In lieu of a central switcher, the DM-RMC-100-1's LAN port may be
used to connect over Ethernet to a 2-Series control system if needed.
Keyboard/Mouse Extender
When connected to a DM-MD series switcher or DM-TX-100 transmitter,
the DM-RMC-100-1 functions as a keyboard/mouse extender, allowing a
USB HID-compliant keyboard and/or mouse to be connected at the display
location, and used to control a computer or other host device located
at the central equipment rack or some other remote location.
Embedded Device Control
The primary objective of every Crestron system is to enable precisely
the control desired for a seamless user experience. The DM-RMC-100-1
includes built-in RS-232, IR, and Ethernet control ports to allow
programmable control of the display device connected to it. But, it
can also provide an alternative to these conventional control methods
by harnessing the CEC (Consumer Electronics Control) signal embedded
in HDMI. Through its connection to the control system, the
DM-RMC-100-1 provides a gateway for controlling the display device
right through the HDMI connection, potentially eliminating the need
www.crestron.com
800.237.2041
for any dedicated control wires or IR probes.
Low-Profile Installation
The DM-RMC-100-1 measures less than 1.3 inches deep and mounts to a
wall, ceiling, or other flat surface. All connections are positioned
along the bottom and top edges of the receiver, allowing cables to be
dressed neatly without obstruction. An array of indicators provide for
easy setup and troubleshooting, verifying the status of connections
and signal activity at a glance.
Please refer to the DigitalMedia Design Guide, Doc. #4789 for
additional information.
> DigitalMedia™ receiver and display controller
> DM CAT input supports up to 450 ft cable length[1]
> Low-profile surface mount design
> Provides one HDMI® or DVI display output[2]
> Handles HD video with Deep Color and 3D
> Includes USB HID keyboard/mouse port
> Enables device control via CEC, RS-232, IR, or Ethernet
> Provides relay screen/lift control
> Supports a power current sensor or contact closure
> Affords single-wire connection from a DM switcher or
transmitter
> Provides 10/100 Ethernet connection for display device or
control system
> Easy setup and diagnostics
DM-RMC-100-1
SPECIFICATIONS
Video
Input Signal Type: DM CAT (DigitalMedia over twisted-pair copper wire)
Output Signal Types: HDMI®, DVI[2]
Formats: HDMI w/Deep Color & 3D, DVI, HDCP content protection support
Input Resolutions, Progressive: [email protected], [email protected] (480p),
[email protected] (576p), [email protected], [email protected], [email protected],
[email protected], [email protected], [email protected], [email protected],
[email protected] (720p50), [email protected] (720p60), [email protected],
[email protected], [email protected], [email protected], [email protected],
[email protected], [email protected], [email protected], [email protected],
[email protected], [email protected], [email protected], [email protected]
(1080p24), [email protected] (1080p25), [email protected] (1080p50),
[email protected] (1080p60), [email protected], [email protected],
[email protected], plus any other resolution allowed by HDMI up to 165MHz
pixel clock
Input Resolutions, Interlaced: [email protected] (480i), [email protected] (576i),
[email protected] (1080i25), [email protected] (1080i30), plus any other
resolution allowed by HDMI up to 165MHz pixel clock
Output Resolutions: Matched to input
Audio
Input Signal Type: DM CAT
Output Signal Type: HDMI
Formats: Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby®
TrueHD, DTS®, DTS-ES, DTS 96/24, DTS-HD High Res, DTS-HD Master
Audio™, Up to 8ch PCM
Communications
DigitalMedia: DM CAT, DMNet, HDCP management, EDID format
management, CEC
Ethernet: 10BaseT/100BaseTX, auto-switching, auto-negotiating, autodiscovery, full/half duplex, TCP/IP, UDP/IP, CIP, DHCP, RSTP
USB: Supports USB HID class devices
Connectors - Bottom
SENS: (1) 2-pin 3.5mm detachable terminal block;
Digital/contact closure sensing input;
Rated for 0-24 Volts DC, referenced to GND;
Input Impedance: 2.2k ohms pulled up to 5 Volts DC;
Logic Threshold: 2.5 Volts DC nominal with 1 Volt hysteresis band
HDMI: (1) 19-pin Type A HDMI female;
HDMI digital video/audio output;
Also supports DVI[2]
USB: (1) USB Type A female;
USB 1.1 host port for connection of a mouse/keyboard or other USB HIDcompliant device
RELAY 1 - 2: (1) 4-pin 3.5mm detachable terminal block comprising (2)
normally open, isolated relays;
Rated 1 Amp, 30 Volts AC/DC;
MOV arc suppression across contacts
COM: (1) 5-pin 3.5mm detachable terminal block, bidirectional RS-232 port;
Up to 115.2k baud, hardware and software handshaking support
IR 1 - 2: (1) 4-pin 3.5mm detachable terminal block comprising (2) IR/Serial
ports;
IR output up to 1.1 MHz;
1-way serial TTL/RS-232 (0-5 Volts) up to 19200 baud
Connectors - Top
LAN: (1) 8-wire RJ45 female w/2 LED indicators;
10BaseT/100BaseTX Ethernet port;
Green LED indicates link status;
Amber LED indicates Ethernet activity
Crestron Electronics, Inc. 15 Volvo Drive | Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 | Fax: 201.767.1905
www.crestron.com
Cable Type:
DM-CBL DigitalMedia CableMaximum length without, between, before, or
after repeaters:
• 200 ft (60 m) for 720p, 1080i, 1080p24
DM-RMC-100-1
• 200 ft (60 m) for 1024x768 @75Hz
• 150 ft (45 m) for 1080p60
• 150 ft (45 m) for 1280x1024 @75Hz
• 150 ft (45 m) for 1920x1200 @60Hz
• 125 ft (38 m) for 1600x1200 @60Hz
• 50 ft (15 m) for 1080p60 Deep Color
Maximum total length using up to 2 repeaters:
•
•
•
•
•
•
•
450 ft (137 m) for 720p, 1080i, 1080p24
450 ft (137 m) for 1024x768 @75Hz
450 ft (137 m) for 1080p60
450 ft (137 m) for 1280x1024 @75Hz
450 ft (137 m) for 1920x1200 @60Hz
375 ft (114 m) for 1600x1200 @60Hz
150 ft (45 m) for 1080p60 Deep Color
Controls & Indicators
PWR: (1) green LED, indicates operating power supplied via DMNet
DM LINK: (1) green LED, indicates connection to an upstream DM device
VIDEO: (1) red/green dual-color LED, indicates video signal presence and
lock status
CNTRL: (1) red/green dual-color LED, indicates Ethernet connection and
control system communication status
SETUP: (1) red LED and (1) miniature recessed pushbutton, for Ethernet
auto-discovery
RESET: (1) miniature recessed pushbutton, for hardware reset
Power Requirements
Available Accessories
DM-CBL-NP-SP500: DigitalMedia™ Cable, non-plenum, 500 ft spool
DM-CBL-P-SP500: DigitalMedia™ Cable, plenum-rated, 500 ft spool
DM-CONN-20: DigitalMedia™ Cable Connectors, 20-Pack
DM-DR: DigitalMedia™ Repeater
CNSP-XX: Custom Serial Interface Cable
IRP2: IR Emitter Probe
CNXRMCS: TV Current Sensor
CBL-HD-1.5: Crestron® Certified HDMI® Interface Cable, 1.5 ft
CBL-HD-3: Crestron® Certified HDMI® Interface Cable, 3 ft
CBL-HD-6: Crestron® Certified HDMI® Interface Cable, 6 ft
CBL-HD-12: Crestron® Certified HDMI® Interface Cable, 12 ft
CBL-HD-20: Crestron® Certified HDMI® Interface Cable, 20 ft
CBL-HD-30: Crestron® Certified HDMI® Interface Cable, 30 ft
CBL-HD-DVI-1.5: Crestron® Certified HDMI® to DVI Interface Cable, 1.5 ft
CBL-HD-DVI-3: Crestron® Certified HDMI® to DVI Interface Cable, 3 ft
CBL-HD-DVI-6: Crestron® Certified HDMI® to DVI Interface Cable, 6 ft
CBL-HD-DVI-12: Crestron® Certified HDMI® to DVI Interface Cable, 12 ft
CBL-HD-DVI-20: Crestron® Certified HDMI® to DVI Interface Cable, 20 ft
CBL-HD-DVI-30: Crestron® Certified HDMI® to DVI Interface Cable, 30 ft
MP-WP152-B: Media Presentation Wall Plate - HDMI®, Black
MP-WP152-W: Media Presentation Wall Plate - HDMI®, White
MP-WP140-B: Media Presentation Wall Plate - DVI-I w/Mini-TRS Stereo
Audio, Black
MP-WP140-W: Media Presentation Wall Plate - DVI-I w/Mini-TRS Stereo
Audio, White
MP-WP185-B: Media Presentation Wall Plate - DigitalMedia™ CAT, Black
MP-WP185-W: Media Presentation Wall Plate - DigitalMedia™ CAT, White
DMNet Power Usage: 6 Watts (0.25 Amps @ 24 Volts DC)
Environmental
Temperature: 41° to 104°F (5° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: 21 BTU/Hr
Enclosure
Chassis: Metal, matte black finish
Mounting: Surface mount (mounting bracket included)
Dimensions
Height: 5.66 in (144 mm)
Width: 5.15 in (131 mm)
Depth: 1.29 in (33 mm) with mounting bracket
Weight
13.8 oz (392 g)
Available Models
DM-RMC-100-1: DigitalMedia™ Room Controller & DM CAT Receiver
Crestron Electronics, Inc. 15 Volvo Drive | Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 | Fax: 201.767.1905
www.crestron.com
Notes:
1. For DigitalMedia CAT wiring, use DM-CBL DigitalMedia Cable. Up to two
DM Repeaters (Model DM-DR) may be required. Refer to the Crestron
DigitalMedia Design Guide, Doc. #4789 for complete wiring guidelines.
2. HDMI requires an appropriate adapter or interface cable to accommodate
a DVI signal. CBL-HD-DVI interface cable available separately.
This product may be purchased from an authorized Crestron dealer. To find a
dealer, please contact the Crestron sales representative for your area. A
list of sales representatives is available online at www.crestron.
com/salesreps or by calling 800-237-2041.
Crestron, DigitalMedia, and DM are trademarks or registered trademarks of
Crestron Electronics, Inc. Dolby, Dolby Digital, and the double-D symbol
are trademarks or registered trademarks of Dolby Laboratories. DTS is a
registered trademark & the DTS logos and Symbol are trademarks of DTS, Inc.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
DM-RMC-100-1
Crestron Electronics, Inc. 15 Volvo Drive | Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 | Fax: 201.767.1905
www.crestron.com
All brand names, product names and trademarks are the property of their respective owners.
©2011 Crestron Electronics, Inc.
Specifications subject to change without notice. 5/17/2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement