ViewSonic VA702b-3 Service manual

ViewSonic VA702b-3 Service manual
Service Manual
ViewSonic VA702-1
VA702b-1
Model No. VS10781
17” Color TFT LCD Display
(VA702-1_ VA702b-1_SM Rev. 1b Sep. 2006)
ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright
Copyright © 2006 by ViewSonic Corporation. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranty of merchantability or fitness for any
particular purpose. Further, ViewSonic reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation of ViewSonic to notify any
person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision
1a
1b
SM Editing Date
10/20/05
9/12/2006
ViewSonic Corporation
ECR Number
Description of Changes
Initial Release
Add 2 nd panel V7 & VA (updated RSPL, BOM)
i
Confidential - Do Not Copy
Editor
G. Han
Jamie Chang
VA702-1_VA702b-1
TABLE OF CONTENTS
1.
Precautions and Safety Notices
1
2.
Specification
4
3.
Front Panel Function Control Description
13
4.
Circuit Description
18
5.
Adjustment Procedure
29
6.
Troubleshooting Flow Chart
35
7.
Recommended Spare Parts List
42
8.
Exploded Diagram and Exploded Parts List
47
9.
Block Diagram
49
10. Schematic Diagrams
50
11. PCB Layout Diagrams
58
ViewSonic Corporation
ii
Confidential - Do Not Copy
VA702-1_VA702b-1
1. Precautions and Safety Notices
1. SAFETY PRECAUTIONS
This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However,
improper used or installation may cause damage to the monitor as well as to the user.
WARNINGS:
z
z
z
z
z
z
z
z
This monitor should be operated only at the correct power sources indicated on the label on the rear of the
monitor. If you’re unsure of the power supply in you residence, consult your local dealer or Power
Company.
Use only the special power adapter that comes with this monitor for power input.
Do not try to repair the monitor by yourself, as it contains no user-serviceable parts. Only the qualified
technician can repair it.
Do not remove the monitor cabinet. There are high-voltage parts inside that may cause electric shock to
human bodies.
Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.
Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power cable immediately
and consult your closed dealer.
Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply
non-ammonia based cleaner onto the cloth, not directly onto the glass screen.
Do not place heavy objects on the monitor or power cord.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety visual inspections and the
protection afforded by them cannot necessarily be obtained by using replacement components rated for
higher voltage, wattage, etc. Before replacing any of these components read the parts list in this manual
carefully. The use of substitute replacement parts, which do not have the same safety characteristics as
specified in the parts list, may create shock, fire, or other hazards.
3. SERVICE NOTES
z
When replacing parts or circuit boards, clamp the lead wires around terminals before soldering.
z
Keep wires away from high voltage, high temperature components and sharp edges.
z
Keep wires in their original position so as to reduce interference.
z
Adjustment of this product please refers to the user’ manual.
ViewSonic Corporation
1
Confidential - Do Not Copy
VA702-1_VA702b-1
4. Handling and Placing Methods
Correct Methods:
Incorrect Methods:
Only touch the metal of the LCD panel or the front
Surface of the LCD panel is pressed by fingers and
cover of he monitor. Do not touch the surface of the
that may cause "Mura".
polarizer.
Taking out the monitor by grasping the LCD panel.
That may cause "Mura".
Take out the monitor with cushions.
ViewSonic Corporation
2
Confidential - Do Not Copy
VA702-1_VA702b-1
Correct Methods:
Incorrect Methods:
Placing the monitor on foreign objects, That could
scratch the surface of the panel or cause "Mura".
Place the monitor on a clean and soft foam pad.
The panel is placed facedown on the lap. That may
cause "Mura".
ViewSonic Corporation
3
Confidential - Do Not Copy
VA702-1_VA702b-1
2. Specification
INTRODUCTION
FEATURES
VA702/b
Size
17 “
Luminance (Typ)
300 cd/㎡
Contrast Ratio (Typ)
500:1
TFTLCD PANEL
Colors (6 bits + 2 bits FRC)
16.2 M
Response Time (Typ)
12 ms
Viewing Angle (H/V)
140 ° / 125 °
Recommend resolution
[email protected]
Size
17 “
Luminance (Typ)
300 cd/㎡
Contrast Ratio (Typ)
500:1
nd
2
Colors
(6
bits
+
2
bits
FRC)
16.2
M
TFTLCD PANEL
Response Time (Typ)
8 ms
Viewing Angle (H/V)
150 ° / 135 °
Recommend resolution
[email protected]
Size
17 “
Luminance (Typ)
280 cd/㎡
Contrast Ratio (Typ)
600:1
3rd
Colors
(6
bits
+
2
bits
FRC)
16.2
M
TFTLCD PANEL
Response Time (Typ)
8 ms
Viewing Angle (H/V)
150 ° / 135 °
Recommend resolution
[email protected]
Analog (75ohms, 0.7/1.0 Vp-p)
Yes
Input Signal
Digital
No
Separate Sync
Yes
Sync Compatibility
Composite Sync
No
Sync on Green
No
PC
Yes
Compatibility
Power Mac
Yes
TV Box (NextVision 6)
Yes
Power Voltage
AC 100-240V, 50/60Hz
Yes
On Mode(Max / Typ)
36 W/ 35 W
Power Consumption
Off Mode (Max)
≦1 W
Yes
Tilt ( 20 ° - -5 °)
Swivel
No
Ergonomics
Pivot
No
Height Adjust
No
OSD Control
[ 1 ] [▼] [▲] [ 2 ] [ ]
Yes
Physical (W x H x D)
378 x 374 x 196 mm
Dimension
Package (W x H x D)
440 x 511 x 132 mm
Physical (Net Weight)
4.5 kg
Weight
Package (Gross Weight)
6.2 kg
Operating Condition Temperature (℉/℃)
32℉-104℉ / 0℃-40℃
Humidity (%)
10 % - 90 %
Temperature (℉/℃)
-4℉-140℉ / -20℃-60℃
Storage Condition
Humidity (%)
5 % - 90 %
UL, cUL, FCC-B, CB, CE, ENERGY, NOM, TUV/GS, TUV ERGO
(covers ISO13406-2 & MPRII), TCO’03, GOST-R+20 ORIGINAL
Regulation
COPIES HYGIENIC, SASO, PCBC, VCCI, BSMI, CCC, (PSB), (CTICK), TUV-S, Green Mark, Energy Star, RoHS, WEEE
ViewSonic Corporation
4
Confidential - Do Not Copy
VA702-1_VA702b-1
GENERAL specification
Test Resolution & Frequency
Test Image Size
Contrast and Brightness Controls
1280x1024 @ 60Hz
Full Size
Factory Default:
Contrast = 70%, Brightness = 100%
VIDEO INTERFACE
Analog Input Connector
Video Cable Strain Relief
Video Cable Connector DB-15 Pin out
Video Signals
Video Impedance
Maximum PC Video Signal
Maximum Mac Video Signal
Sync Signals
DDC 1/2B
Sync Compatibility
Video Compatibility
Resolution Compatibility
Exclusions
ViewSonic Corporation
DB-15 (Analog), refer the appendix A
Equal to twice the weight of the monitor for
five minutes
Compliant DDC 1/2B
Video RGB (Analog) - Separate
75 Ohms (Analog)
950 mV with no damage to monitor
1250 mV with no damage to monitor
LVDS
Compliant with Revision 1.3
Separate Sync
Shall be compatible with all PC type
computers, Macintosh computers, and after
market video cards
640 x 350, 640 x 480, 720 x 400 (640 x
400*), 800 x 600, 832 x 624, 1024 x 768,
1152 x 870, 1280 x 720, 1280 x 1024
Not compatible with interlaced video
5
Confidential - Do Not Copy
VA702-1_VA702b-1
POWER SUPPLY
Internal Power Supply
Input Voltage Range
Input Frequency Range
Short Circuit Protection
Over Current Protection
Leakage Current
Efficiency
Fuse
Power Dissipation
Max Input AC Current
INRUSH CURRENT (COLD START)
Power Supply Cold Start
Power Supply Transient Immunity
Power Supply Line Surge Immunity
Power Supply Missing Cycle Immunity
Power Supply Acoustics
US Type Power Cable
European Type Power Cable
CCC Type Power Cable
PSE Type Power Cable
Power Saving Operation(Method)
Power Consumption
Recovery Time
ViewSonic Corporation
Part Number: ILIPI-004
90 TO 264 VAC
47.5 TO 63 HERTZ
Output can be shorted without damage
2.4 A typical at 14.2 VDC
3.5mA (Max) at 254VAC / 60Hz
80% typical at 115VAC Full Load
Internal and not user replaceable
35 Watts (typ)
0.8 Arms @ 90VAC, 0.4 Arms @265VAC
30 A @ 120VAC, 50 A (max) @ 220VAC
Shall start and function properly when
under full load, with all combinations of
input voltage, input frequency, and
operating temperature
Shall be able to withstand an ANSI/IEEE
C62.41-1980 2000V 200 ampere ring wave
transient test with no damage
Shall be able to withstand 1.5 times
nominal line voltage for one cycle with no
damage
Shall be able to function properly, without
reset or visible screen artifacts, when ½
cycle of AC power is randomly missing at
nominal input
The power supply shall not produce audible
noise that would be detectable by the user.
Audible shall be defined to be in compliance
with ISO 7779 (DIN EN27779:1991) Noise
measurements of machines acoustics.
Power Switch noise shall not be considered
Separate 3-prong NEMA 5-15P type plug.
Length = 1.8m. Connects to display.
Color = Black
Schuko CEE7-7 type plug.
Length = 1.8m, Connects to display.
Color = Black
Separate 3-prong type plug.
Length = 1.8m. Connects to display.
Color = Black
Separate 2-prong NEMA 1-15P type plug.
Length = 1.8m. Connects to display.
Color = Black
VESA DPMS Signaling
On Mode < 36 W (max) / 35 W(typ)
Off Mode< 1W
On Mode = N/A, Active Off < 3 sec
6
Confidential - Do Not Copy
VA702-1_VA702b-1
ELECTRICAL REQUIREMENT
Horizontal / Vertical Frequency
Horizontal Frequency
Vertical Refresh Rate
30 – 82 KHZ
50 – 85* HZ.
* WHEN THE RESOLUTION IS SET TO 1280 X 1024, THE
VERTICAL REFRESH RATE MAY BE UP TO 75 HZ; FOR ALL
OTHER RESOLUTIONS, THE VERTICAL REFRESH RATE MAY
BE UP TO 85HZ.
Maximum Pixel Clock
Sync Polarity
140 MHz
Independent of sync polarity.
Timing Table
Item
Timing
1
640 x 350 @ 70Hz, 31.5kHz
2
640 x 400 @ 60Hz, 31.5kHz
3
640 x 400 @ 70Hz, 31.5kHz
4
640 x 480 @ 50Hz, 24.7kHz
5
640 x 480 @ 60Hz, 31.5kHz
6
640 x 480 @ 67Hz, 35.0kHz
7
640 x 480 @ 72Hz, 37.9kHz
8
640 x 480 @ 75Hz, 37.5kHz
9
640 x 480 @ 85Hz, 43.27kHz
10
720 x 400 @ 70Hz, 31.5kHz
11
800 x 600 @ 56Hz, 35.1kHz
12
800 x 600 @ 60Hz, 37.9kHz
13
800 x 600 @ 75Hz, 46.9kHz
14
800 x 600 @ 72Hz, 48.1kHz
15
800 x 600 @ 85Hz, 53.7kHz
16
832 x 624 @ 75Hz, 49.7kHz
17
1024 x 768 @ 60Hz, 48.4kHz
18
1024 x 768 @ 70Hz, 56.5kHz
19
1024 x 768 @ 72Hz, 58.1kHz
20
1024 x 768 @ 75Hz, 60.0kHz
21
1024 x 768 @ 85Hz, 68.67kHz
22
1152 x 870 @ 75Hz, 68.7kHz
23
1280 x 1024 @ 60Hz, 63.4kHz
24
1280 x 1024 @ 75Hz, 79.97kHz
25
1280x 720 @ 60Hz, 45kHz (HDTV)
Analog
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Primary Presets
1280x1024 @ 60Hz
User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO
configuration
Changing Modes
● Maximum Mode Change Blank Time for image stability: 3 seconds (Max), excluding
“Auto Image Adjust” time.
● Under DOS mode (640 x 350, 720 x 400 & 640 x 400), it should recall factory setting
when execute “Auto Image Adjust”.
● The monitor needs to do “Auto Image Adjust” the first time when a new mode is
detected. (See section “0-Touch™ Function Actions”)
ViewSonic Corporation
7
Confidential - Do Not Copy
VA702-1_VA702b-1
AUDIO INTERFACE (SPEAKER SPECIFICATION)
No Audio function
TFT LCD PANEL
Panel Characteristics:
1st Source Panel
Model number
Type
Active Size
Pixel Arrangement
Pixel Pitch
GLASS TREATMENT
# OF BACKLIGHTS
BACKLIGHT LIFE
Luminance (Center) –
Condition:
CT = 6500K, Contrast = Max, Brightness =
Max
Brightness Uniformity (13 points)
Contrast Ratio
Color Depth
Viewing Angle (Horizontal)
VIEWING ANGLE (VERTICAL)
Response Time
10%-90% @ Ta=25°C
Panel Defects
ViewSonic Corporation
Innolux MT170EN01 V1
TN type with LVDS interface
337.9 (H) x 270.3 (V)
RGB Vertical Stripe
0.264 mm
Anti Glare (Hard coating 3H)
4 CCFL edge-light (2 top / 2 bottom)
40,000 Hours (Min) / 50,000 (Typ)
300 cd/m2 (Typ after 30 minute warm up)
250 cd/m2 (Min after 30 minute warm up)
0.8 (Typ), 0.75(Min)
δ = Min Luminance of 13 points/Max Luminance
of 13 points
500:1 (Typ), 400:1 (min)
16.2 million colors (6 bits + 2 bits FRC)
@ CR>= 5
@ CR>=10
Typical: 160º
Typical: 140º
Minimum: 130º
Minimum: 150º
@ CR>= 5
@ CR>=10
Typical: 160º
Typical: 130º
Minimum: 120º
Minimum: 150º
12 ms (Tr= 3 ms, Tf = 9 ms) (typ)
16 ms (Tr= 5 ms, Tf = 11 ms)(max)
Please see Panel Quality Specifications.
8
Confidential - Do Not Copy
VA702-1_VA702b-1
2nd Source Panel
Model number
Type
Active Size
Pixel Arrangement
Pixel Pitch
GLASS TREATMENT
# OF BACKLIGHTS
BACKLIGHT LIFE
Luminance (Center) –
Condition:
CT = 6500K, Contrast = Max,
Brightness = Max
Brightness Uniformity (13 points)
Contrast Ratio
Color Depth
Viewing Angle (Horizontal)
Innolux MT170EN01 V4
TN type with LVDS interface
337.9 (H) x 270.3 (V)
RGB Vertical Stripe
0.264 mm
Anti Glare (Hard coating 3H)
4 CCFL edge-light (2 top / 2 bottom)
40,000 Hours (Min) / 50,000 (Typ)
300 cd/m2 (Typ after 30 minute warm up)
250 cd/m2 (Min after 30 minute warm up)
0.8 (Typ), 0.75(Min)
δ = Min Luminance of 13 points/Max
Luminance of 13 points
500:1 (Typ), 400:1 (min)
16.2 million colors (6 bits + 2 bits FRC)
@ CR>=10
Typical: 150º
@ CR>= 5
Typical: 170º
@ CR>=10
Typical: 135º
VIEWING ANGLE (VERTICAL)
Response Time
10%-90% @ Ta=25°C
Panel Defects
ViewSonic Corporation
@ CR>= 5
Typical: 155º
8 ms (Tr= 2 ms, Tf = 6 ms) (typ)
18 ms (Tr= 7 ms, Tf = 11 ms)(max)
Please see Panel Quality Specifications.
9
Confidential - Do Not Copy
VA702-1_VA702b-1
3rd Source PAnel
Model number
Type
Active Size
Pixel Arrangement
Pixel Pitch
GLASS TREATMENT
# OF BACKLIGHTS
BACKLIGHT LIFE
Luminance (Center) –
Condition:
CT = 6500K, Contrast = Max,
Brightness = Max
Brightness Uniformity (13 points)
Contrast Ratio
Color Depth
Viewing Angle (Horizontal)
VIEWING ANGLE (VERTICAL)
Innolux MT170EN01 V7
TN type with LVDS interface
337.9 (H) x 270.3 (V)
RGB Vertical Stripe
0.264 mm
Anti Glare (Hard coating 3H)
4 CCFL edge-light (2 top / 2 bottom)
40,000 Hours (Min) / 50,000 (Typ)
280 cd/m2 (Typ after 30 minute warm up)
250 cd/m2 (Min after 30 minute warm up)
0.8 (Typ), 0.75(Min)
δ = Min Luminance of 13 points/Max
Luminance of 13 points
600:1 (Typ), 400:1 (min)
16.2 million colors (6 bits + 2 bits FRC)
@ CR>=10
@ CR>=10
Typical: 150º
Typical: 140º
Minimum: 130º
@ CR>= 5
Typical: 170º
@ CR>=10
Typical: 135º
@ CR>=10
Typical: 130º
Minimum: 120º
@ CR>= 5
Typical: 155º
Response Time
10%-90% @ Ta=25°C
Panel Defects
ViewSonic Corporation
8 ms (Tr= 2 ms, Tf = 6 ms) (typ)
16 ms (Tr= 6 ms, Tf = 10 ms)(max)
Please see Panel Quality Specifications.
10
Confidential - Do Not Copy
VA702-1_VA702b-1
IMAGE PERFORMANCE
Factory Defaults
Item
Contrast
Brightness
Color Temperature
Sharpness
720x400/640x400
Defaults
70%
100%
6500K
33%
720x400
Luminance
Lv (Max) –
Condition:
Contrast = 100%
Brightness = 100%
Color Temperature = 6500K
Lv (Def) –
Condition:
Contrast = Default
Brightness = Default
Color Temperature = 6500K
Preset Color Temperatures
SRGB
Preset 1 9300K
CCT (Max) = 10250K.
CCT (Min) = 8500K
Preset 2 6500K (Primary)
CCT (Max) = 6950K
CCT (Min) = 6100K
Preset 3 5400K
CCT (Max) = 5915K
CCT (Min) = 4935K
Preset Color Temperature
Adjustability
ViewSonic Corporation
Defaults
50%
50%
15 Sec
On
Enabled
Same as the Luminance in section
4-7 “TFT LCD PANEL”
Lv (Def) / Lv (Max) x 100% ≧ 85%
Display Size
Horizontal Display Size, Primary Preset
Vertical Display Size, Primary Preset
Saturation
Contrast = Default
Brightness = Default
Test Pattern = 32-Gray
Contrast = 100%
Brightness = 100%
Test Pattern = 32-Gray
Item
OSD H. Position
OSD V. Position
OSD Time Out
OSD Background
Resolution Notice
Full Screen
Full Screen
No visible saturation
6 – 8 level saturation (Max)
It should meet IEC 61966-2-1 (1999-10) standard
Wx= 0.283 +/- 0.02,
Wy= 0.298 +/- 0.02
Wx= 0.313 +/- 0.02
Wy= 0.329 +/- 0.02
Wx= 0.335 +/- 0.02
Wy= 0.350 +/- 0.02
Each color preset shall be adjustable. Red, Green,
and Blue shall be individually controlled.
11
Confidential - Do Not Copy
VA702-1_VA702b-1
MECHANICAL
Dimension (Desktop)
Width
Height
Depth
Monitor Weight
378mm (14.9 inch)
374 mm (14.7 inch)
196 mm ( 7.7 inch)
4.5 Kg (9.9 lbs)
*Refer to Figure 1
Dimension (Head Only / Wall Mount) – Unfolding the Monitor Stand
Width
378 mm (14.9 inch)
Height
424 mm (16.7 inch)
Depth
61 mm (2.38 inch)
Monitor Weight
4.5 Kg (9.9 lbs)
*Refer to Figure 1
Ergonomics
Tilt Up
Tilt Down
Cabinet Material
Display Head Plastic Material
Neck/Base Plastic Material
Internal Plastic Cabinet Components
Front Bezel Color
Neck, Base, and Rear Cover Color
Rear logo color
Cabinet Color Drift Due To UV-Light
Cabinet Texture
Samples
ViewSonic Corporation
From 0º up to ≧20º
From 0º down to -3º ~ -5 º
ABS UL94-HB
ABS UL94-HB
All internal plastic cabinet components shall be
in compliance with the requirements of TCO’03
The reference for the bezel is the silver color
(VA702) and the midnight gray color (VA702b)
chip provided by ViewSonic
The reference for the bezel is the black color
(VA702) and the midnight gray color
(VA702b) chip provided by ViewSonic.
The color difference between any two cabinet
components shall be less than 0.80 “Delta E”, in
the 1976 CIE L*a*b Colorspace.
The rear logo is silver color with the black color
background (VA702) and midnight gray color
and background (VA702b) chip provided by
ViewSonic
The color drift due to UV-Light shall be less than
3.0 “Delta E” in the 1976 CIE L*a*b colorspace.
Testing shall be performed according to the
requirements of ASTM Test Method D4459-93.
Mold-Tech # 11010 used on all external textured
surfaces.
The supplier shall submit textured color chips,
plastic material specifications, and Material
Safety Data Sheets for approval.
12
Confidential - Do Not Copy
VA702-1_VA702b-1
3. Front Panel Function Control Description
Adjusting the Screen Image
Use the buttons on the front control panel to display and adjust the OSD controls which display
on the screen. The OSD controls are explained at the top of the next page and are defined in
“Main Menu Controls” on page 10.
Main Menu
with OSD controls
Front Control Panel
shown below in detail
Power light
Green = ON
Orange = Power Saving
Displays the control screen
for the highlighted control.
Also toggles between two
controls on some screens.
Also a shortcut to Auto
Image Adjust.
Standby Power
On/Off
Scrolls through
menu options and
adjusts the
displayed control.
Also a shortcut to
display the
Contrast
adjustment control
screen.
Displays the
Main Menu or
exits the
control screen
and saves
adjustments.
ViewSonic Corporation
13
Confidential - Do Not Copy
VA702-1_VA702b-1
Do the following to adjust the display setting:
1. To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 15
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2. To select a control to adjust, pressSorTto scroll up or down in the Main Menu.
3. After the desired control is selected, press button [2]. A control screen like the one shown
below appears.
The line at the bottom of the screen shows
the current functions of buttons 1 and 2:
Exit or select the Brightness control.
4. To adjust the setting, press the upSor downTbuttons.
5. To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:
• Adjust the computer's graphics card so that it outputs a 1280 x 1024 @ 60Hz video signal to
the LCD display. (Look for instructions on “changing the refresh rate” in the graphics card's
user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION until the
screen image is completely visible. (The black border around the edge of the screen should
barely touch the illuminated “active area” of the LCD display.)
ViewSonic Corporation
14
Confidential - Do Not Copy
VA702-1_VA702b-1
Main Menu Controls
Adjust the menu items shown below by using the upSand downTbuttons.
Control
Explanation
Auto Image Adjust automatically sizes, centers, and fine tunes the video signal
to eliminate waviness and distortion. Press the [2] button to execute Auto Image
Adjust.
NOTE: Auto Image Adjust works with most common video cards. If this
function does not work on your LCD display, then lower the video refresh rate
to 60 Hz and set the resolution to its pre-set value.
Contrast adjusts the difference between the image background (black level)
and the foreground (white level).
Brightness adjusts background black level of the screen image.
Color Adjust provides several color adjustment modes, including preset color
temperatures and a User Color mode which allows independent adjustment of
red (R), green (G), and blue (B). The factory setting for this product is 6500K
(6500 Kelvin).
sRGB - This is quickly becoming the industry standard for color management,
with support being included in many of the latest applications. Enabling this
setting allows the LCD display to more accurately display colors the way they
were originally intended. Enabling the sRGB setting will cause the Contrast and
Brightness adjustments to be disabled.
9300K - Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).
6500K - Adds red to the screen image for warmer white and richer red.
5400K - Adds green to the screen image for a darker color.
ViewSonic Corporation
15
Confidential - Do Not Copy
VA702-1_VA702b-1
Control
Explanation
User Color - Individual adjustments for red (R), green (G), and blue (B).
1. To select color (R, G or B) press button [2].
2. To adjust selected color, pressSorT.
3. When all color adjustments are complete, press button [1] twice.
Information displays the timing mode (video signal input) coming from the
graphics card in the computer, the LCD model number, the serial number, and
the ViewSonic® website URL. See your graphics card’s user guide for
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1280 x 1024 @ 60Hz (recommended) means that the resolution
is 1280 x 1024 and the refresh rate is 60 Hertz.
Manual Image Adjust
H./V. Position (Horizontal/Vertical Position) moves the screen image left or
right and up or down. Press button [2] to toggle between Horizontal and
Vertical. The Horizontal setting moves the screen image to the left or to the
right. The Vertical setting moves the screen image up and down.
H. Size (Horizontal Size) adjusts the width of the screen image.
Fine Tune sharpens the focus by aligning text and/or graphics with pixel
boundaries.
NOTE: Try the Auto Adjust function before using the Fine Tune control.
Sharpness adjusts the clarity and focus of the screen image.
ViewSonic Corporation
16
Confidential - Do Not Copy
VA702-1_VA702b-1
Control
Explanation
Setup Menu displays the menu shown below:
Language Select allows the user to choose the language used in the menus and
control screens.
Resolution Notice advises the optimal resolution to use.
OSD Position allows the user to move the OSD menus and control screens.
OSD Timeout sets the length of time the OSD screen is displayed. For example,
with a “15 second” setting, if a control is not pushed within 15 seconds, the
display screen disappears.
OSD Background allows the user to turn the OSD background On or Off.
Memory Recall returns the adjustments back to factory settings if the display is
operating in a factory Preset Timing Mode listed in the Specifications of this
manual.
ViewSonic Corporation
17
Confidential - Do Not Copy
VA702-1_VA702b-1
4. Circuit Description
Electronic Circuit Theory
1 Switching Mode Power Supply
1.1 AC Current Input Circuit
P801 is a connector for connecting AC Power. F801 is a fuse to protect all the circuit. AC input voltage
is from 90V to 264V. R820 and R821 joined between two inputting main circuit to prevent man from
shock. L801 is used to clear up low frequency wave. C801 and C806 are used to discharge the waves
that L801 produced. High frequency waves are damped by C801 and C806. D801 is a rectifier which
composed of 4 build-in diodes, it inverts AC to DC.
1.2 High Voltage to Low Voltage Control Circuit
C805 is used to smooth the wave from rectifier. IC802 is a highly integrated PWM controller, which
build-in a power MOSFET. When rectified DC high voltage is applied to the DRAIN pin during start-up,
the MOSFET is off initially, and the CONTROL pin capacitor is charged through a switched high
voltage current source connected internally between the DRAIN and CONTROL pins. When the
CONTROL pin voltage Vc reaches approximately 5.8V, the control circuitry is activated and the
soft-start begins. The soft-start circuit gradually increases the duty cycle of the MOSFET from zero to
the maximum value over approximately 10ms. If no external feedback/supply current is fed into the
CONTROL pin by the end of the soft-start, the high voltage current source is turned off and the
CONTROL pin will start discharging in response to the supply current drawn by the control circuitry.
Resistor R803, R807, R824 and R825 are for line over voltage shut-down (OVP) and line under-voltage
detection (UVP).Resistors R801, R805, R822, and R823 are for external current limit adjustment, and
used to reduce the current limit externally to a value close to the operating peak current of primary about
1.35A. The mean is power will protected when the primary current over about 1.35A.
When PWM is turned off, the main current flow will be consumed through D804 and ZD802, This will
prevent MOSFET which built-in IC802 from being damaged under large current impulse and voltage
spike.
D806 and C815 provide internal Auxiliary current to CONTROL pin during normal operation. In
addition, error amplifier and feedback current to the CONTROL pin are for duty cycle control.
1.3 DC_5V and DC_14V Output Circuit
For DC 5V, D805 is used to rectify the inducted current. R806 and C811 are used to store energy when
current is reversed. The parts including C812, C814, C822, C821, B801 and L803 are used to smooth
the current waves.
For DC 14V, D803 is used to rectify the inducted current. R802 and C802 are used to store energy when
current is reversed. The parts including C808, C810 and L802 are used to smooth the current waves.
1.4 Feedback and OVP Protect Circuit
Pin R of IC803 is supplied 2.5V stable voltage. It is connected to 5V and 14V output through R811,
R810 and R818. R811, R810 and R818 are output sampling resistor. When the sampling voltage more
than 2.5V or less than 2.5V, feedback current of IC802 will change, this can change the voltage from
transformer T801.
For 5VDC output OVP, ZD803 is a zener diode, when 5V output voltage becomes up to 5.6V, the zener
current cause R819 voltage become up to 0.7V, Q801 is triggered and OVP starts. For 12VDC output
OVP, ZD804 is a Zener Diode, when 14V output voltage becomes up to 16V, the zener current cause
R819 voltage become up to 0.7V, Q801 is triggered and OVP starts. The collector current of Q801 is
used to make build-in diode light. FB Current of IC802 will be changed; it can change the voltage from
T801.
Q802, R827, R828 and ZD801 make up of dummy loading circuit. For start-up sequence, during 5V
output take place high loading first, this dummy loading circuit operated to insure 14V not be increased.
ViewSonic Corporation
18
Confidential - Do Not Copy
VA702-1_VA702b-1
2 Inverter circuit
2.1 Low voltage to high voltage circuit
12VDC supplies the power to IC501 through F501; the control signals that BRIGHTNESS and ON/OFF
come from I/F board. ON/OFF signal connect to pin8 of IC501 and makes IC501 enabled.
BRIGHTNESS is connected to pin7 of IC501 to adjust the panel luminance. R524, R529, C505 make
up of a delay-time circuit and R528, R523, R524 make up of a voltage divided circuit. C504 is used to
filter the high frequency noise. The operation frequency is determined by R522 and C529. For BURST
MODE, its dimming frequency is determined by R527 and C506. C502 is used for soft start and
compensation, C502, C528 are used to filter noise.
The output drives, including NDR4, NDRV2, PDRV3, PDRV1 (pins1, 3, 15, 16 respectively), generate a
square pulses to drive MOSFET U501, U502. And U501, U502 works as full-bridge topology, it is high
efficient, zero voltage switch.
During start up, VSEN (pin9) detects the voltage at the transformer secondary. When VSEN reaches
3.0V, the output voltage is regulated. If no current is detected for around 1.5 seconds, IC501 will shut
down.
The current flowing through CCFL is detected and regulated through sense resistor R509, R511. The
feedback voltage through R506, R507, and C508 connected to Pin11 (ISEN), and then compared with a
reference voltage (1.5V) via a current amplifier, resulting in PWM drive outputs to full-bridge switches.
2.2 Protection circuit
Over Voltage Protection: R501and R502 are connected in high voltage output connector, the divided AC
voltage is inverted DC voltage through D508, R505 and C507are used to rectify wave & dump noise.
Then the voltage signal reaches Pin9 VSEN of IC501, when the voltage changes, build-in PWM of
IC501 will adjust output voltage.
Open Lamp Protection: In normal operation, the resistors R510, R511, R512, R509 are sensed a high
level AC voltage, the AC signal IS1 invert DC voltage through D509, R515, C533, and the high level
DC voltage reaches the gate pin of Q502, similarly, the gate pin of Q503, Q504, Q505 has high level DC
voltage. So the gate pin of Q501 has a low level voltage, and the IC501 is normal operation. Once one
of signal IS1, IS2, IS3, and IS4 is low, the voltages of Q501 gate pin is high level, and make the voltage
of ISEN low level, the IC501 will shut down.
3 I/F Board Circuit
3.1 Power Input
+5V is from the power board and supply for U101(FS8860-18PJ)﹑U102(FS8860-33PJ)﹑
U105(MCU:W78E65P) and panel. +3.3V output is generated from +5V through C169 and C102
filtering, and U102 outputs. +3.3V is used for U104 (Scaler: TSU16AK). +1.8V output is generated
from +5V through C169, C105 and C102 filtering, and U101 outputs. +1.8V is also used for U104.
3.2 MCU (W78E65P)
VDD is +5V and its frequency of XTAL1 is 22.1184MHz. U105 #2 is defined as panel-enable. When
the I/O port is low, Q101 and Q102 are conducted. And then after C109 and C110 filtering, obtain the
voltage of VLCD, which will be connected to CN103. U105 #3 is defined as CCFL-enable. When the
I/O port is low, Q103 is pulled up and the backlights are on; When the I/O port is high, Q103 is
conducted and the backlights are off. U105 #4 is defined as DET-VGA, connected with CN102 #5.
U105 #14, #36, #37, #38, #39, #40, #41, #42, #43 are the communications with U104 (Scaler), which
are connected to #72, #31, #78, #77, #30, #70, #71, #69, #32 of Scaler. U105 #43 outputs reset signal to
U104 (Scaler).
U106 is EEPROM used for saving EDID data, which is connected by SCL and SDA pins with #16 and
#17 of MCU. Connect #12 to #26 of U105 for ISP.
3.3 Scaler (TSU16AK)
The frequency of XTAL2 is 14.318MHz. U104 #1, #102-#103, #106-#113, #118-#125, #128 output
LVDS digital data of 8 bit to panel control circuit through CN103. U104 #73 generates a PWM
waveform by regulating the duty to control the brightness of the backlights. U104 #30-#32, #69-#72,
#77-#78 are the communications with U105 (MCU) that are connected to #36-#43 of MCU. These
communications include HWRESET, CSZ/ALE, SCL/RDZ, SDA/WRZ, and AD0-AD3.
ViewSonic Corporation
19
Confidential - Do Not Copy
VA702-1_VA702b-1
3.4 VGA Input
Signal R, G, B, SOG input through CN102 #1, #2, #3, and C115, C116, C117 and C118 filtering the
high frequency noise. Signal HSYNC and VSYNC input through CN102 #13 and #14, and C119, R119,
C120, R120 filtering. Then the analog signal enters U104, and then U104 deals with it internally. In
addition, TVS101, TVS102, TVS103 (the three are BAV99), TVS104, TVS105, TVS106, TVS107 (they
are constant voltage diode of 5V6) are ESD protector. Signal DDC-SCL inputs via CN102 #15, and then
passes through TVS107 for ESD protection, goes into EDID EEPROM IC U103. Signal DDC-SDA
inputs via CN102 #12, and then passes through TVS106 for ESD protection, goes into EDID EEPROM
IC U103. CN102 #5 is defined as cable detect pin, this detector realizes via R107 and U105 #4. The
PC-5V of U103 is supplied by PC via CN103 #9 with D103 for ESD protection, or supplied by Monitor
self via D104.U103 is an EEPROM IC, which is a kind of memory and used for saving EDID data.
3.5 Button Control
Button “Key-Power” is defined as power on/off, which is connected to U105 #24 through CN106 #4.
Button “Key-2” is defined as two functions of selecting and adjustment, which is connected to U105
#25 through CN106 #1.
Button “Key-Up” is defined as plus, which is connected to U105 #26 through CN106 #3.
Button “Key-Down” is defined as minus, which is connected to U105 #27 through CN106 #5.
Button “Key-1” is defined as two functions of menu and exit, which is connected to U105 #28 through
CN106 #2.
LED indicator on the front bezel is defined as follows:
a. When press button “Key-Power”, U105 #6 is pulled down and U105 #7 is pulled high, so Q104 is
conducted and the LED indicator is green.
b. When in power-saving mode, U105 #6 is pulled high and U105 #7 is pulled down, so Q105 is
conducted and the LED indicator is orange.
3. FACTORY PRESET TIMING TABLE
Item
Resolution
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
640 x 350
640 x 400
640 x 400
640 x 480
720 x 400
800 x 600
832 x 624
1024 x 768
1152 x 870
1280 x 1024
ViewSonic Corporation
1280 x 720
H-Freq.
(KHz)
31.5kHz
31.5kHz
31.5kHz
24.7kHz
31.5kHz
35.0kHz
37.9kHz
37.5kHz
43.27kHz
31.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
53.7kHz
49.7kHz
48.4kHz
56.5kHz
58.1kHz
60.0kHz
68.67kHz
68.6kHz
63.4kHz
79.97kHz
45kHz
20
V-Freq.
(Hz)
70Hz
60Hz
70Hz
50Hz
60Hz
67Hz
72Hz,
75Hz,
85Hz
70Hz
56Hz
60Hz
72Hz
75Hz
85Hz
75Hz
60Hz
70Hz
72Hz
75Hz
85Hz
75Hz
60Hz
75Hz
60Hz
Confidential - Do Not Copy
Dot Clock
(MHz)
25.2
25.2
25.2
19.8
25.2
30.2
31.5
31.5
36.0
28.3
36.0
40.0
50.0
49.5
56.3
57.3
65.0
75.0
78.5
78.8
94.5
100
108
135
74.2
VA702-1_VA702b-1
4. Power On/Off Sequence
4.1 Hardware Power ON
When power cord is plugged into AC socket, SMPS starts work and provides U105 and U106 with
VCC5V. When VCPU inputs to U105, U105 resets circuit active, sets U105 all registers to preset modes,
and then U105 #43 sends out a HWRESET signal voltage to reset U104, and then monitor goes into
stand-by mode. That means hardware power on has been completed.
4.2 Software Power ON/OFF
When press power key, U105 #24 recieves low pulse, and sends out “Power on/off” order back to U104,
and then U104 will do the power on/off.
- If Power ON, U105 #6 (LED_Green) will send out High potential, and then LED green on.
- If Power OFF, U105 #7 (LED_Orange) will send out High potential, and then LED Orange on.
The Panel_Vcc, Backlight_En, CLK/DATA output to panel will follow the following sequency.
T1 (ms)
0.1~10
T2 (ms)
0~10
T3 (ms)
>200
T4 (ms)
>100
T5 (ms)
0~50
T6 (ms)
0.1~10
T7 (ms)
>1000
3
5. AC Outlet Pin Assignment
2
1
P801
Pin
Symbol
Description
1
2
3
L
N
E
Live
Neutral
GND
6. Inner Connector Pin Assignment
6.1 CN501, CN502, CN503, CN504 (Connect to Panel Backlight, SM02B-BHSS-1-TB or equivalent)
Pin
Symbol
Description
1
H.V.
High voltage for lamp
2
L.V.
Low voltage for lamp
6.2 CN101 (Power BD to Interface BD)
Pin
Symbol
No.
1,2
+5V (VCC5V)
+5.2V output
3,6
GND
Ground
ViewSonic Corporation
Description
21
Confidential - Do Not Copy
VA702-1_VA702b-1
4
5
BRIGHTNESS
ON/OFF
Brightness Control
CCFL on/off Control
6.3 CN106 (Interface BD to Keypad)
Pin
Symbol
Description
No.
1
KEY_SELECT/AUTO Select control and auto adjustment control
2
KEY_MENU/EXIT
OSD page selection and exit
3
KEY_UP
OSD “▲” control to adjust value to increase
4
KEY_POWER
DC power on/off control
5
KEY_DOWN
OSD “▼” control to adjust value to decrease
6
LED_GREEN
Green LED lighting control
7
GND
Ground
8
LED_ORANGE
Orange LED lighting control
6.4 CN103 (Connect I/F BD to panel, FI-X30S-H or Equivalent)
Pin No.
Symbol
Function
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
RXO0RXO0+
RXO1RXO1+
RXO2RXO2+
GND
RXOCRXOC+
RXO3RXO3+
RXE0RXE0+
GND
RXE1RXE1+
GND
RXE2RXE2+
RXECRXEC+
RXE3RXE3+
GND
GND
GND
GND
VCC
VCC
VCC
minus signal of odd channel 0(LVDS)
plus signal of odd channel 0(LVDS)
minus signal of odd channel 1(LVDS)
plus signal of odd channel 1(LVDS)
minus signal of odd channel 2(LVDS)
plus signal of odd channel 2(LVDS)
Ground
minus signal of odd clock channel (LVDS)
plus signal of odd clock channel (LVDS)
minus signal of odd channel 3(LVDS)
plus signal of odd channel 3(LVDS)
minus signal of even channel 0(LVDS)
plus signal of even channel 0(LVDS)
Ground
minus signal of even channel 1(LVDS)
plus signal of even channel 1(LVDS)
Ground
minus signal of even channel 2(LVDS)
plus signal of even channel 2(LVDS)
minus signal of even clock channel (LVDS)
plus signal of even clock channel (LVDS)
minus signal of even channel 3(LVDS)
plus signal of even channel 3(LVDS)
Ground
Ground
Ground or Open
Ground
Power supply (5.0 V)
Power supply (5.0 V)
Power supply (5.0 V)
6.5 CN102 (D-SUB Connector)
Pin
1
2
3
Symbol
Red video input
Green video input
Blue video input
ViewSonic Corporation
Pin
6
7
8
Symbol
Red GND
Green GND
Blue GND
22
Pin
11
12
13
Symbol
NC
Serial data (SDA)
H / H+V SYNC
Confidential - Do Not Copy
VA702-1_VA702b-1
4
5
NC
Cable Detect
9
10
+5V(from PC)
GND
14
15
VSYNC
Data clock line (SCL)
7. Key Parts Pin Assignment
7.1 IC802 (TOP246Y, Power Control IC)
Pin
Symbol
I/O
Description
1
C
I
Control
2
L
I
Line Sense
3
X
I
External Current Limit
4
S
O
Source of MOSFET(GND)
5
F
I
Frequency
6
D
I
Drain of MOSFET
7.2 IC501 (OZ9910G, CCFL inverter controller IC)
Pin No.
Symbol
I/O
Description
Bottom MOSFET gate drive output in dual forward
1
NDRV4
O
converter
2
PGND
High-current power ground
Bottom MOSFET gate drive output in dual forward
3
NDRV2
O
converter
4
GNDA
Low-current signal ground
5
CT
I
Timing capacitor of high frequency oscillator
6
LCT
I
Timing capacitor of set LPWM frequency
7
ADJ
I
Control command input –DC
8
ENA
I
Enable input
I
9
VSEN
Voltage sense feedback
I
10
CMP_SST
Soft start and loop compensation capacitor
11
12
13
14
15
ISEN
VREF
VIN
HSB
PDRV3
16
PDRV1
7.3 U104 (TSU16AK)
Pin
Symbol
1
LVBOM
2
GND
3
BYPASS
4
NC
5
NC
6
BUSTYPE
7
NC
8
NC
9
NC
10 GND
11
VDDP
12 NC
13 NC
14 NC
15 NC
16 NC
ViewSonic Corporation
I
O
I
I
O
O
Current sense feedback
Reference voltage output
Supply voltage for IC
High side driver buffer output
Top MOSFET gate drive output in dual forward converter
Top MOSFET gate drive output in dual forward converter
I/O
O
IN
O
Description
B-Link Negative LVDS Differential Data
Ground
For External Bypass Capacitor
Not connected
Not connected
Low : Serial bus; High : Direct bus
Not connected
Not connected
Not connected
Ground
Digital Output Power
Not connected
Not connected
Not connected
Not connected
Not connected
23
Confidential - Do Not Copy
VA702-1_VA702b-1
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
NC
VDDC
GND
GND
VDDP
NC
NC
NC
NC
NC
NC
NC
NC
AD0
AD3
HWRESET
XIN
XOUT
AVDD_MPLL
GND
HSYNC0
VSYNC0
GND
NC
NC
GND
NC
NC
VDD_ADC
NC
NC
GND
NC
NC
VDD_ADC
REXT
AVDD PLL
GND
AVDD ADC
GND
BINOM
BINO
GINOM
GINO
SOGIN0
RINOM
RINO
GND
AVDD_ADC
REFP
REFM
GND
ALE/CS
WRZ/SDA
RDZ/SCL
INT
PWM0
PWM1
NC
NC
ViewSonic Corporation
I
O
I/O
I/O
I
I
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I/O
I
O
O
O
Not connected
Digital Core Power
Ground
Ground
Digital Output Power
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
DDR direct bus AD0; 4mA driving strength
DDR direct bus AD3; 4mA driving strength
Hardware reset; active high
Crystal Oscillator Input
Crystal Oscillator Output
MPLL Power
Ground
Analog HSYNC input
Analog VSYNC input
Ground
Not connected
Not connected
Ground
Not connected
Not connected
ADC Power
Not connected
Not connected
Ground
Not connected
Not connected
ADC Power
External resistor 390 ohm to AVDD ADC
PLL Power
Ground
ADC Power
Ground
Reference ground for analog blue input
Analog blue input
Reference ground for analog green input
Analog green input
Sync-on-green input
Reference ground for analog red input
Analog red input
Ground
ADC Power
Internal ADC top de-coupling pin
Internal ADC bottom de-coupling pin
Ground
DDR direct bus ALE; active high
DDR direct bus WRZ; active low
DDR direct bus RDZ; active low
CPU interrupt; 4mA driving strength
PWM0; 4mA driving strength
PWM1; 4mA driving strength
Not connected
Not connected
24
Confidential - Do Not Copy
VA702-1_VA702b-1
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
AD1
AD2
NC
NC
NC
NC
NC
VDDP
GND
GND
VDDC
NC
NC
NC
NC
NC
NC
VDDP
GND
GND
VDDC
NC
NC
NC
NC
LVA3P
LVA3M
VDDP
GND
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
VDDP
GND
GND
VDDC
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
VDDP
ViewSonic Corporation
I/O
I/O
O
I
O
I
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
DDR direct bus AD1; 8mA driving strength
DDR direct bus AD2; 8mA driving strength
Not connected
Not connected
Not connected
Not connected
Not connected
Digital Output Power
Ground
Ground
Digital Core Power
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Digital Output Power
Ground
Ground
Digital Core Power
Not connected
Not connected
Not connected
Not connected
A-Link Positive LVDS Differential Data
A-Link Negative LVDS Differential Data
Digital Output Power
Ground
A-Link Positive LVDS Differential Clock
A-Link Negative LVDS Differential Clock
A-Link Positive LVDS Differential Data
A-Link Negative LVDS Differential Data
A-Link Positive LVDS Differential Data
A-Link Negative LVDS Differential Data
A-Link Positive LVDS Differential Data
A-Link Negative LVDS Differential Data
Digital Output Power
Ground
Ground
Digital Core Power
B-Link Positive LVDS Differential Data
B-Link Negative LVDS Differential Data
B-Link Positive LVDS Differential Clock
B-Link Negative LVDS Differential Clock
B-Link Positive LVDS Differential Data
B-Link Negative LVDS Differential Data
B-Link Positive LVDS Differential Data
B-Link Negative LVDS Differential Data
Digital Output Power
25
Confidential - Do Not Copy
VA702-1_VA702b-1
127
128
GND
LVBOP
O
Ground
B-Link Positive LVDS Differential Data
7.4 U105 (Micro-controller: W78E65P-40)
Pin
1
2
3
4
5
Symbol
P4.2/INT3
P1,0/T2
P1.1/T2EX
P1.2
P1.3/PWM0
I/O
O
O
I
O
6
P1.4/PWM1
O
7
P1.5/PWM2
O
8
9
10
11
P1.6/PWM3
P1.7/PWM4
RST
P3.0/RXD
12
P4.3/INT2
13
14
15
16
17
18
P3.1/TXD
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
P3.6/WR
19
P3.7/RD
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
XTAL2
XTAL1
GND
P4.0
P2.0/A8
P2.1/A9
P2.2/A10
P2.3/A11
P2.4/A12
P2.5/A13
P2.6/A14
P2.7/A15
PSEN
ALE
P4.1
35
EA
36
37
38
39
40
41
42
43
44
P0.7/AD7
P0.6/AD6
P0.5/AD5
P0.4/AD4
P0.3/AD3
P0.2/AD2
P0.1/AD1
P0.0/AD0
+5V
ViewSonic Corporation
I
I
O
O
I/O
I
O
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
I
Description
A bi-directional I/O port with alternate function.
Enable panel power on
Enable CCFL work
VGA cable detection
provide alternated function of PWM Volume
provide alternated function of PWM Green LED
lighting control
provide alternated function of PWM Orange LED
lighting control
Function is the same as that of standard 8052
Function is the same as that of standard 8052
Reset control pin
SCL line of I2C for EDID, debug function
PORT 4: A bi-directional I/O port with alternate
function.
SDA line of I2C for EDID, debug function
Interrupt request control pin
Shut Down Volume Mute standard 8052.
SCL line of I2C communication with EEPROM
SDA line of I2C communication with EEPROM
DVI cable detection standard 8052.
EEPROM write protection control for DVI EDID
Prevent E2PROM Write in standard 8052.
Crystal 22.1184MHz In
Crystal 22.1184MHz out
Sink voltage ground
A bi-directional I/O port with alternate function.
DC power on/off control
OSD “►” control to adjust value to increase
OSD “◄” control to adjust value to decrease
Selection of menu command listed
OSD page selection
Auto adjustment control
A bi-directional I/O port with internal pull-ups
A bi-directional I/O port with internal pull-ups
Program Store Enable
Address Latch Enable
A bi-directional I/O port with alternate function
External Access Enable external ROM. The ROM
address and data will not be presented on the bus if
the EA pin is high and the program counter is
within the 64 KB area.
DDR Direct Bus Communication with Scaler
DDR Direct Bus Communication with Scaler
DDR Direct Bus Communication with Scaler
DDR Direct Bus Communication with Scaler
WRZ line of DDR Direct Bus
RDZ line of DDR Direct Bus
ALE line of DDR Direct Bus
Hardware reset to Scaler
+5V for MCU working voltage
26
Confidential - Do Not Copy
VA702-1_VA702b-1
Disassembly Block
VA702/b (INL PANEL)DIS-ASSEMB LY BLOCK
BASE SUB-ASSM *1
HINGE COVER*2
(SCREW,P,CROSS,M5*22, Ni*4)
BEZEL SUB-ASSM *1
(SCREW,B,CROSS,T4*10, BLK*4)
BEZEL
SUB-ASSM(G/S)
BUTTON FUNCTION KEY*1
FRONT BEZEL (G/S)*1
BACK COVER
SUB-ASS’Y
HINGE,RIGHT*1
HINGE,LEFT*1
(SCREW,F,CROSS,T4*10, Ni*4)
(SCREW,I ,CROSS,M3*4,Zw*1)
LED LENS*1
SUPPORT VESA *1
BACK COVER *1
Rubber spacer*1
Logo *1
BACK COVER SUB-ASS’Y*1
BRACKET_R*1
GROUND WIRE*1
KEYPAD CABEL*
KEYPAD ASSM*1
(SCREW,PW,CROSS,M3*5, Ni *2)
(SCREW,I ,CROSS,M3*4,Zw*2)
(Ace tape*4)
BASE COVER
SUB-ASS’Y
PLATE BASE *1
BASE COVER *1
INL PANEL*1
BRACKET_R*1
(SCREW,PW,CROSS,M3*5, Ni *2)
(SCREW,I ,CROSS,M3*4,Zw*2)
(Ace tape *2)
IF BOARD*1
POWER BOARD*1
FFC CABLE*1
CLIP,WIRE*1
(SCREW,PW,CROSS,M3*5, Ni*5)
(BOLT, #4-40x11.8, Ni*2)
CHASSIS*1
INSULATOR,MYLAR*1
Note: Arrows are disassembly directions.
ViewSonic Corporation
27
Confidential - Do Not Copy
VA702-1_VA702b-1
Assembly Block
VA702/b (INL panel)ASSEMBLY BLOCK
CHASSIS*1
FRONT BEZEL (G/S)*1
LOGO PLATE,THREE BRID*1
INSULATOR,MYLAR*1
IF BOARD*1
POWER BOARD*1
FFC CABLE*1
CLIP,WIRE*1
(SCREW,PW,CROSS,M3*5, Ni*4)
(BOLT, #4-40x11.8, Ni*2)
LED LENS*1
BUTTON FUNCTION KEY*1
LOGO PLATE
“VIEWSONIC”*1
SUPPORT VESA *1
LOGO PLATE(ELLIPSE)*1
INL PANEL*1
BRACKET_L*1
(SCREW,PW,CROSS,M3*5, Ni*2)
(SCREW,I ,CROSS,M3*4,Zw*2)
(Ace tape*2)
BRACKET_R*1
GROUND WIRE*1
KEYPAD CABEL*1
KEYPAD ASSM*1
(SCREW,PW,CROSS,M3*5, Ni*2)
(SCREW,I ,CROSS,M3*4,Zw*2)
(Ace tape*4)
Rubber*1
PLATE BASE *1
RUBBER FOOT LE1708 *4
BEZEL
SUB-ASSM(G/S
)
BACK COVER *1
BACK COVER
SUB-ASS’Y
BASE COVER *1
BASE COVER
SUB-ASS’Y
BASE SUB-ASSM *1
OPENING STAND LABEL*1
HINGE COVER*2
(SCREW,P,CROSS,M5*22, Ni*4)
BACK COVER SUB-ASS’Y*1
HINGE,RIGHT*1
HINGE,LEFT*1
(SCREW,F,CROSS,T4*10, Ni*4)
(SCREW,I ,CROSS,M3*4,Zw*1)
S/N LABEL*1
QC LABEL*1
HI POT LABEL*1
BEZEL SUB-ASSM *1
ID LABEL*1
(SCREW,B,CROSS,T4*10, BLK*4)
V17 LCD MONITOR
FINAL ASM(INL)
Note: Arrows are assembly directions.
ViewSonic Corporation
28
Confidential - Do Not Copy
VA702-1_VA702b-1
5. Adjustment Procedure
1.
Key Function Description
CONTROL
KEY
[AUTO] [2]
By pressing [AUTO] key, “Auto Image Adjust” is performed
[MENU] [1]
By pressing [MENU] key, Main menu display
[▼] [▲]
[POWER]
2.
KEYS FUNCTION
A. When “MENU OSD” display, press these keys to change the contents of an
adjustment item, or change an adjustment value
B. When “MENU OSD” is un-display, press these keys to change brightness
and contrast
Power on or power off the monitor
Hot Key Operation
CONTROL
KEY
[▼] + [▲]
[1] + [2]
[1] + [▼] +
[▲]
KEYS FUNCTION
Recall Contrast or Brightness while in the Contrast or Brightness
adjustment, or recall both of Contrast and Brightness when the OSD is
not open.
Toggle 720x400 and 640x400 mode when input 720x400 or 640x400 mode.
White Balance (Not shown on user’s guide)
[1] + [▼]
Power Lock
[1] + [▲]
OSD Lock
Remark : All the short cuts function are only available while OSD off
3.
OSD Control
3.1 OSD table
Layer 1
Auto Image Adjust
Contrast/Brightness
Color Adjust
Layer 2
Contrast (+ / -)
Brightness (+ / -)
Srgb
9300K
6500K
5400K
Red (+ / -)
Green (+ / -)
Blue (+ / -)
User Color
Information
Manual Image Adjust
H Position (+ / -)
V Position (+ / -)
+/-
H/V Position
H Size
ViewSonic Corporation
Layer 3
29
Confidential - Do Not Copy
VA702-1_VA702b-1
Fine Tune
Sharpness
Language Select
Setup Menu
Resolution Notice
OSD Position
OSD Time Out
OSD Background
+/+/English
French
German
Italian
Spanish
Finnish
Japanese
Simplified Chinese
Traditional Chinese
On/Off
H Position (+ / -)
V Position (+ / -)
On/Off
Memory Recall
3.2 OSD lock Menu function
Item
Activate OSD lock
OSD Lock Menu Function Check
Method
Phenomenon
Press any of buttons"1", "▼",
[1] + [▲] 10S
"▲", "2" will appear "OSD
Locked" 3s
Deactivate OSD lock: [1] + [▲] 10S(again)
NOTICE:
When the OSD is locked will lock all functions.
Status bar indicating OSD Lock or Unlock is in progress and when complete it will
indicate “OSD Locked”
OSD Lock should not lock Power Button and Power Lock function
3.3 Power lock Menu function
Item
Activate Power Lock
Power Lock Menu Function Check
Method
Phenomenon
Can not turn off the LCD;
Press the power button will
appear "Power Button Locked"
[1] + [▼] 10S
OSD 3s;
LCD would automatically turn
back "On" when power is
restored after a power failure
Deactivate Power
[1] + [▼] 10S(again)
Lock
NOTICE:
Status bar indicating Power Button lock or unlock is in progress and when complete it will
indicate “Power Button Locked”
Power should only be lockable in the “On State”
ViewSonic Corporation
30
Confidential - Do Not Copy
VA702-1_VA702b-1
3.4 Resolution notice function
Resolution Notice Menu
Method
Phenomenon
Resolution Notice OSD should
show on screen after changing to
Activate Resolution
non-native mode for 30 sec,
-----Notice Menu
And it should disappear after 10s
or by pushing button [1] or [2]
Deactivate
Push button [2] under Resolution
Resolution
Notice
------Notice OSD, select Disable
Menu
Item
3.5 Factory Mode Introduction
When input the signal, press “power key” to turn off the monitor. Press” [▼] +[▲] +[ ] “at the
same time so as to enter factory mode. After power on, press ‘’Menu[1]’’ key, you can see the
Factory menu.
INL
: Currently using panel model name
V2 050526
: Currently using firmware version information.
Auto Color
: Automatically calibrate chip ADC parameter by using chip internal DAC
Color Temperature : The R, G, B of 9300K and 6500K and 5400K and User Mode
Colors are all generated from scaling back end.
4. Burn-in pattern
If it is a new monitor, and in factory mode, if no VGA signal input, Burn-in pattern will self
generate automatically. Burn in patterns are: full Red, Green, Blue, White and Black. You can not escape
from Burn-in pattern until plug in VGA Cable, and then press the power key. Turn the monitor off and
then turn it on.
5. Auto Color (Automatically calibrate chip ADC parameter by using chip internal
DAC)
If it is a new-built set and it is first time to do the “auto color”, please confirm the following steps:
-Connect the VGA cable with the standard video pattern generator and display 16-gray pattern on
the monitor.
- Press “Power” to power off the monitor.
- Press” [▼] +[▲] +[ ] “simultaneously to enter factory mode.
- Press ‘’Menu[1]’’, then press ‘’Auto[2]’’ to execute Auto color item.
- After the “Auto Color” process finished, please press “Power” to restart monitor.
6. EDID (Rewrite EDID data to EEPROM)
If we need to rewrite the EEPROM data, please confirm the following steps.
1. Plug in VGA Cable; we can rewrite the EDID data to EEPROM by using “EDID Rewrite”
program.
2. If the “EDID Rewrite” process finished, please pull out VGA cable and press ‘’2’’+’’▲’’ at the
same time.
3. Pull out AC power cable or press power key to restart.
ViewSonic Corporation
31
Confidential - Do Not Copy
VA702-1_VA702b-1
7. Upload firmware to MCU via VGA Cable
7.1 Connect ISP board between monitor and PC as below configure
D-SUB
15PIN
RS232
9PIN
Insert to
RS232 9pin
CON on PC
D-SUB
15PIN
ISP Board
LCD Monitor
D-Sub
Service
cable
PC
VGA
output
Normal
shipping
cable
+12V Adapter
7.2 Before plug in the power cord, make sure keep “▲“ key to be pressed, when power on you can
enter ISP mode.
7.3 8051ispwriter.exe will detect automatically which MCU used in this monitor. Do it as the order
shown on the screen, choose the corresponding firmware version, and load to MCU.
7.4 After finish, please plug out power cable and re-start monitor again.
8 After repair, to ensure the quality you should do the following test and
adjustment
Item
Test OSD
function
Contrast Check
Content
1.Signal is set as [email protected]
2. LCM button are from left to right, checking whether each
single function key and compound function key can be
worked.
1. Set input mode to [email protected]
2. Set Pattern to 32 gray shades
3. Set contrast to the max. The brightest 5~6 shades brightness
cannot be distinguished.
Equipment
Chroma
Signal Generator
Chroma
Signal Generator
Color
Temperature
1. Do “Auto color” at 1280 x [email protected], 32gray shades
2. Measure color temperature, check it complies with the
following temperature:
5400K x=0.335 +/- 0.02, y=0.350 +/- 0.02
6500K x=0.313 +/- 0.02, y=0.329 +/- 0.02
9300K x=0.283 +/- 0.02, y=0.298 +/- 0.02
Chroma Signal
Generator and color
analyzer
Modes switching
check
1. Use Chroma Pattern Generator to make sequence.
VESA (640x480 800x600 1024x768 1280x1024), MAC
832x624 DOS (640x350 720x400), the detail supported
modes and power saving signal.
2. Confirm the above timing modes must be full screen and
the picture must be normal.
3. LED is Orange at power saving mode.
Chroma Signal
Generator
ViewSonic Corporation
32
Confidential - Do Not Copy
VA702-1_VA702b-1
Y measurement
at default setting
Panel Flicker
check
Power saving
1. Set brightness to default value 100 and contrast to default
value 70 at 6500K
2. At full white patter, Measure Y, which should be
250+/-10cd/m² (QDI 220+/- 10cd/m²)
1. Mode: [email protected]
2. Set Brightness& contrast to default value
3. Do “Auto Image Adjust”
4. Shut down PC to check whether there’s glitter on the center
of the picture.
1. Mode: [email protected]
2. Pattern: full white
3. Brightness: Max.
4. Contrast: Default
5. Check power consumption at each modes
Power
State
LED color
Consumption
<38W
Normal
Green
<1W
Stand By
Orange
<1W
Power Key Off
No
ViewSonic Corporation
33
Confidential - Do Not Copy
Chroma Signal
Generator and Color
Analyzer
Equipment::
Chroma Signal
Generator & PC
Chroma signal
generator and Power
meter
AC input:
230V/50Hz
VA702-1_VA702b-1
6. Troubleshooting Flow Chart
1.
Common Acknowledge
z
If you change the interface board, be sure that the U105, U106 and U103 these three components also
changed to the new I/F board because there was program inside. If not, please re-write EDID or upload
firmware into MCU via VGA Cable.
If you adjust clock and phase, please do it at the condition of Windows shut down pattern.
If you confirm the R.G.B. color is normal or not, please do it under 16-grey scalar pattern.
This LCM is analog interface. So if the entire screen is an abnormal color that means the problem happen
in the analog circuit part, if only some scale appears abnormal color that stand the problem happen in the
digital circuit part.
If you check the H/V position, please use the crosshatch pattern.
This LCM support more than 30 timing modes, if the input timing mode is out of specification, the picture
may appears abnormally.
If brightness uneven, repairs Inverter circuit or change a new panel.
If you find the vertical line or horizontal line lost on the screen, please change panel.
z
z
z
z
z
z
z
ViewSonic Corporation
34
Confidential - Do Not Copy
VA702-1_VA702b-1
2. No Power & Power LED Off
No power
Check circuit
if short
Check primary
rectifier voltage
Check IC802,
C805, T801
Check F801, P801,
D801
Check pin3 of
IC802 voltage
about 1V
Check R801, R805,
R822, R823, R817
Check pin2 of IC802
voltage about 2V
Check R803, R807,
R824, R825
Check pin1 of IC802
voltage is 5.8V
Check R812, R816,
C818
END
ViewSonic Corporation
35
Confidential - Do Not Copy
VA702-1_VA702b-1
3.
DC output voltage is unstable
Output Voltage Unstable
Check Vbe of
Q801 below 0.3V
Check ZD801, ZD802,
ZD803, D803, D805
Check circuit if
short
Check Q801, Q802
Check reference
voltage
Check pinR
of IC801
Check R809, R814,
IC801, R818
Check R810, R811
Check feedback
circuit
Check Vpin3-4 of
IC801 about 6V
Check C815, D806,
R812
Check Vpin1-2 of
IC801 about
1V
Check R809,
R814
END
ViewSonic Corporation
36
Confidential - Do Not Copy
VA702-1_VA702b-1
4. Output power is unstable
Unstable power
Check sampling
Circuit
Check R810,
R811, R818
Change R810, R811,
R818
Check the C pin
voltage of IC803
if 3V
Check the R pin
voltage of IC803
about 2.5V
Change
IC803
Check R809, R808, R814,
D809
Check pin1 of
IC802 voltage
is 5.8V
Check D806, C815 if
short
Change
D806, C815
Check pin3 of
IC802 voltage
about 1V
Change R801, R805,
R822, R823, R817
END
ViewSonic Corporation
37
Confidential - Do Not Copy
VA702-1_VA702b-1
5. Backlight can’t be turned on
No raster?
Yes
LED Green?
Yes
Backlight cannot be
turned on.
Yes
No
Is there 14Vdc voltage
on pin13 of IC501?
Check power
supply
Yes
No
Is R526 Ok?
Is there high-level voltage
on pin8 of IC501?
Yes
Check I/F
board
No
Yes
R526 open
Connecting the
output connector
again
No
Check CN501,
CN502, CN503 and
CN504?
Yes
No
Is there pulse waveform on
pin1, pin3, pin15 and pin16 of
IC501 at the moment of restart?
Is Ok IC501?
Yes
U501, U502 fail
No
IC501 fail
Yes
No
T501, T502 fail
Is ok T501, T502?
Yes
ViewSonic Corporation
Check protected circuit Q501,
Q502, Q503, Q504
38
END
Confidential - Do Not Copy
VA702-1_VA702b-1
6. Black Screen and backlight turn on
ViewSonic Corporation
39
Confidential - Do Not Copy
VA702-1_VA702b-1
7.
White Screen
White Screen
OK
LVDS Cable Reinsert
Workmanship
NG
OK
Change LVDS Cable
LVDS Cable NG
NG
Check VLCD is 5V
OK
Check LVDS signals
NG
Check
Q101,Q102,Q107,R103
Panel Fail
NG
Check Panel-Enable of
U105(pin2) is low
OK
OK
Check the HWRESET of
U104 exists
NG
Check RP101
OK
NG
Check the pins of
U105
END
ViewSonic Corporation
40
Confidential - Do Not Copy
VA702-1_VA702b-1
8.
Bad Screen
Bad Screen
OK
LVDS Cable Reinsert
Workmanship
NG
OK
Change LVDS Cable
LVDS Cable NG
NG
1.Check
X101,C154,C155
2.Check
X102,C126,C168
NG
Check Crystal:pin20,21 of
U105 and pin 33,34 of U104
OK
NG
Check the communication of
U104 and U105
Check ALE/RDZ/
WRZ/AD0/AD1/AD2/
AD3/HWRESET
OK
Check the pins of
U104 and U105
ViewSonic Corporation
41
Confidential - Do Not Copy
VA702-1_VA702b-1
7. Recommended Spare Parts List
RECOMMENDED SPARE PARTS LIST (VA702-1)
ViewSonic Model Number: VS10781
Rev: 1b
Serial No. Prefix: PST
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Description
ECR/ECN
ViewSonic P/N
Ref. P/N
Location
Universal number#
KIT,ACCESSORY(INL), LE1709
A-00003039
703000000500
PWR CORD 10A/125V BLK 6FT UL/CSA,SVT 18x
A-00003040
453070800250
PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx0. RoHS
Added on 9/11/06
A-00005255
453070800170R
KIT,ACCESSORY,VA702-INL V7,LE1709 RoHS
Added on 9/11/06
A-00005274
703000000506R
B-00003041
790411300600
PC Board Assembly: PCBA,IF BOARD, LE1709-6A0
PCBA,KEYPAD BOARD, LE1709
B-00003042
790411500000
PCBA,KEYPAD BOARD, LE1709 RoHS
Added on 9/11/06
B-00005278
790411500000R
PCBA,PWR&INV./B, LE1709-6A0
B-00003043
790411400600
PCBA,PWR&INV./B, LE1709-6A0 RoHS
Added on 9/11/06
B-00005279
790411400600R
PCBA,IF BOARD(V7), LE1709- 6A0 RoHS
Added on 9/11/06
B-00008066
790411300630R
BASE, LE1709
C-00003044
501240201000
Cabinets:
BEZEL,FRONT(SILVER),VA702, LE1709
C-00003045
501010202700
COVER,BACK, LE1709
C-00003046
501020202900
ASSY,BASE, LE1709 RoHS
Added on 9/11/06
C-00005262
714020002400R
ASSY,BEZEL(S),LE1709,VA702 RoHS
Added on 9/11/06
C-00005263
714030002400R
ASSY,BACK COVER, LE1709 RoHS
Added on 9/11/06
C-00005264
714050002400R
COVER,HINGE, LE1709 RoHS
Added on 9/11/06
C-00006088
501020203000R
CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40
CB-00003047
453010100100
Cables:
CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40 RoHS
Added on 9/11/06
CB-00005254
453010100100R
HRN LVDS FFC 30P 234mm,RoHSACCX30234KU28 RoHS
Added on 9/11/06
CB-00005259
430303000140R
HRN ASS'Y 4x2P 189mm UL2651#28SZ504479B, RoHS
Added on 9/11/06
CB-00005260
430300800320R
HRN ASS'Y 1P 137mm BLACK,UL100 7 #20, RoHS
Added on 9/11/06
CB-00005261
430300100210R
LCD PANEL 17" MT170EN01-V1(INNOLUX)
E-00003048
631102070270
Electronic
LCD PANEL 17" MT170EN01-V7-G1,AM17000057 RoHS
Added on 9/11/06
E-00008006
631102071910R
Components:
LCD PANEL 17" MT170EN01-V7-G2,AM17000057 RoHS
Added on 9/11/06
E-00008007
631102071920R
LCD PANEL 17" MT170EN01-V7-G3,AM17000057 RoHS
Added on 9/11/06
E-00008008
631102071930R
SCREW,B,CROSS,T.T-4*10,BLK ,RoHS
Added on 9/11/06
HW-00005265
509412610500R
Hardware:
SCREW,F,CROSS,T.T-4*10,Ni RoHS
Added on 9/11/06
HW-00005266
509212610300R
SCREW,P,CROSS,M5*22,Ni,RoHS
Added on 9/11/06
HW-00005267
509116822300R
SCREW,PW,CROSS,W/WAS,M3*5,NI RoHS
Added on 9/11/06
HW-00005269
509146305300R
BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN. RoHS
Added on 9/11/06
HW-00005270
509000000700R
SCREW,I,CROSS,M3*4,Zw,RoHS
Added on 9/11/06
HW-00005271
509016304102R
HINGE,RIGHT, LE1709 RoHS
Added on 9/11/06
HW-00005276
502060401910R
HINGE,LEFT, LE1709 RoHS
Added on 9/11/06
HW-00005277
502060401900R
GENERIC FOAM SET
Added on 9/11/06
P-00001347
30833
Packing Material:
GENERIC BOX
Added on 9/11/06
P-00002515
20653
P-00003049
506120004300
BAG,PLASTIC,L550xW450xT0.05mm,LE1709
CARTON,VA702, LE1709
P-00003050
506020006800
CARTON,VA702, LE1709 RoHS
Added on 9/11/06
P-00005256
506020006800R
CUSHION,EPS-L, LE1709
P-00003051
506040005500
CUSHION,EPS-L, LE1709 RoHS
Added on 9/11/06
P-00005257
506040005500R
P-00003052
CUSHION,EPS-R, LE1709
506040005510
CUSHION,EPS-R, LE1709 RoHS
Added on 9/11/06
P-00005253
506040005510R
BAG,PE+EPE,L590xW480xT0.6mm (PRINTED)LE1 RoHS
Added on 9/11/06
P-00005272
506120300400R
BAG,PLASTIC,l690xW(455+145)xT0.05mm, LE1 RoHS
Added on 9/11/06
P-00005273
506120004500R
Plastics:
RUBBER,FOOT,OD14.1xT2.5mm,3M, LE1708
PL-00003053
503020002600
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to
eliminate repeated cross checks of each item between this version and prior versions.
Accessories:
ViewSonic Corporation
42
Confidential - Do Not Copy
VA702-1_VA702b-1
RECOMMENDED SPARE PARTS LIST (VA702B-1)
ViewSonic Model Number: VS10781
Rev: 1b
Serial No. Prefix: PSX
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Accessories:
Board Assembly:
Cabinets:
Cables:
Electronic
Components:
Hardware:
Packing Material:
Plastics:
Description
PWR CORD 10A/125V BLK 6FT UL/CSA,SVT 18x
KIT,ACCESSORY,VA702B-INL,LE1709
PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx0. RoHS
PCBA,IF BOARD, LE1709-6A0
PCBA,KEYPAD BOARD, LE1709
PCBA,KEYPAD BOARD, LE1709 ROHS
PCBA,PWR&INV./B, LE1709-6A0
PCBA,PWR&INV./B, LE1709-6A0 ROHS
PCBA,IF BOARD(V7), LE1709- 6A0 ROHS
BASE, LE1709
COVER,BACK, LE1709
BEZEL,FRONT(GRAY),VA702b, LE1709
ASSY,BASE, LE1709 RoHS
ASSY,BACK COVER, LE1709 RoHS
COVER,HINGE, LE1709 RoHS
ASSY,BEZEL(G),LE1709,VA702b RoHS
CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40
CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40 RoHS
HRN LVDS FFC 30P 234mm,RoHSACCX30234KU28 RoHS
HRN ASS'Y 4x2P 189mm UL2651#28SZ504479B, RoHS
HRN ASS'Y 1P 137mm BLACK,UL100 7 #20, RoHS
LCD PANEL 17" MT170EN01-V1(INNOLUX)
LCD PANEL 17" MT170EN01-V7-G1,AM17000057 RoHS
LCD PANEL 17" MT170EN01-V7-G2,AM17000057 RoHS
LCD PANEL 17" MT170EN01-V7-G3,AM17000057 RoHS
SCREW,B,CROSS,T.T-4*10,BLK ,ROHS
SCREW,F,CROSS,T.T-4*10,Ni ROHS
SCREW,P,CROSS,M5*22,Ni,ROHS
SCREW,PW,CROSS,W/WAS,M3*5,NI RoHS
BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RoHS
SCREW,I,CROSS,M3*4,Zw,ROHS
HINGE,RIGHT, LE1709 RoHS
HINGE,LEFT, LE1709 RoHS
BAG,PLASTIC,L550xW450xT0.05mm,LE1709
FOAM,EPS-L, LE1709
FOAM,EPS-L, LE1709 RoHS
FOAM,EPS-R, LE1709
FOAM,EPS-R, LE1709 RoHS
BOX,VA702B, LE1709
BOX,VA702b, LE1709 RoHS
BAG,PE+EPE,L590xW480xT0.6mm (PRINTED)LE1 RoHS
BAG,PLASTIC,l690xW(455+145)xT0.05mm, LE1 RoHS
GENERIC BOX
GENERIC FOAM SET
RUBBER,FOOT,OD14.1xT2.5mm,3M, LE1708
ECR/ECN
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
Added on 9/11/06
ViewSonic P/N
A-00003040
A-00003054
A-00005255
B-00003041
B-00003042
B-00005278
B-00003043
B-00005279
B-00008066
C-00003044
C-00003046
C-00003055
C-00005262
C-00005264
C-00006088
C-00008095
CB-00003047
CB-00005254
CB-00005259
CB-00005260
CB-00005261
E-00003048
E-00008006
E-00008007
E-00008008
HW-00005265
HW-00005266
HW-00005267
HW-00005269
HW-00005270
HW-00005271
HW-00005276
HW-00005277
P-00003049
P-00003051
P-00005257
P-00003052
P-00005253
P-00003056
P-00008079
P-00005272
P-00005273
P-00002515
P-00001347
PL-00003053
Ref. P/N
453070800250
703000000510
453070800170R
790411300600
790411500000
790411500000R
790411400600
790411400600R
790411300630R
501240201000
501020202900
501010202710
714020002400R
714050002400R
501020203000R
714030002410R
453010100100
453010100100R
430303000140R
430300800320R
430300100210R
631102070270
631102071910R
631102071920R
631102071930R
509412610500R
509212610300R
509116822300R
509146305300R
509000000700R
509016304102R
502060401910R
502060401900R
506120004300
506040005500
506040005500R
506040005510
506040005510R
506020006810
506020006810R
506120300400R
506120004500R
20653
30833
503020002600
Location
Universal number#
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic
Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
ViewSonic Corporation
43
Confidential - Do Not Copy
VA702-1_VA702b-1
BOM LIST (VA702-1)
ViewSonic Model Number: VS10781
Serial No. Prefix: PST
Rev: 1b
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
ViewSonic P/N
CB-00005261
CB-00005260
CB-00005259
CB-00005254
A-00003675
A-00003671
A-00006733
A-00006734
N/A
N/A
C-00006088
N/A
N/A
N/A
N/A
N/A
HW-00005277
HW-00005276
N/A
N/A
N/A
N/A
N/A
N/A
N/A
P-00005256
N/A
N/A
N/A
P-00005257
P-00005253
N/A
N/A
N/A
P-00005272
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
HW-00005270
HW-00005271
HW-00005267
HW-00005269
HW-00005266
HW-00005265
N/A
E-00008006
E-00008007
E-00008008
N/A
C-00005262
C-00005263
C-00005264
N/A
N/A
B-00008066
B-00005279
B-00005278
Ref. P/N
430300100210R
430300800320R
430303000140R
453010100100R
453070800230R
453070800420R
453070800480R
453070800500R
501010202700R
501020202900R
501020203000R
501030201900R
501120101200R
501240201000R
502020300700R
502020300710R
502060401900R
502060401910R
502080300300R
502090301300R
502170300400R
503010001700R
503020002600R
505040202000R
505040203600R
506020006800R
506037003700R
506039001200R
506039002301R
506040005500R
506040005510R
506102000300R
506102000400R
506102000500R
506120300400R
506150001310R
506250005102R
506380001800R
506380002100R
506381000700R
506390000400R
506390000600R
506390210110R
506390400100R
506390500100R
506431000300R
506440002300R
506440002400R
506440002600R
506440003000R
509000000700R
509016304102R
509116822300R
509146305300R
509212610300R
509412610500R
511100001500R
631102071910R
631102071920R
631102071930R
703000000500R
714020002400R
714030002400R
714050002400R
71407276B100R
71408276B100R
790411300630R
790411400600R
790411500000R
ViewSonic Corporation
Description
HRN ASS'Y 1P 137mm BLACK,UL1007 #20,RoHS
HRN ASS'Y 4x2P 189mm UL2651#28SZ504479B,
HRN LVDS FFC 30P 234mm,RoHSACCX30234KU28
CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40
PWRCORD 5A/250V BLK 6FT UK3Gx.75mm(SP60/ For V7 Panel
PWRCORD 10A/250V BLACK 6FT SAA,H05W-F/3G For V7 Panel
PWRCORD 7A/125V BLK 6FT CNS,VCTF 3Gx0.75 For V7 Panel
PWRCORD 16A/250V BLK 6FT KTL,H05VV-F 3Gx For V7 Panel
BEZEL,FRONT(SILVER),VA702,LE1709
COVER,BACK, LE1709
COVER,HINGE, LE1709
BUTTON,FUNCTION KEY, LE1709
LENS, LE1709
BASE, LE1709
BRACKET,LEFT, LE1709
BRACKET,RIGHT, LE1709
HINGE,LEFT, LE1709
HINGE,RIGHT, LE1709
SUPPORT,VESA, LE1709 ROHS
CHASSIS, LE1709
PLATE,BASE,LE1709
RUBBER,SPACER,L25xW10xT4.0mm,LE1709
RUBBER,FOOT,OD14.1xT2.5mm,3M, LE1708 ROH
INSULATOR,MYLAR,L79.7xW62.7mm,CHASSIS, L
INSULATOR,PET,355x292x0.1mm, LE1709
CARTON,VA702, LE1709
CARDBOARD,COVER,L1120xW980xH120xT5mm,LE1
CORNER PAPER,820x50x50mm
CORNER PAPER,2050x50x50xT3mm,LE1709 ROHS
CUSHION,EPS-L, LE1709
CUSHION,EPS-R, LE1709
LOGO PLATE,VIEWSONIC, LE1709
LOGO PLATE,VIEWSONIC, LE1709(THREE BIRDS
LOGO PLATE,VIEWSONIC, LE1709(ELLIPSE)
BAG,PE+EPE,L590xW480xT0.6mm(PRINTED)LE19
PALLET,1120x980x120mm.LE1709 ROHS
LBL,AGENCY(VA702), LE1709(KOREA MARK)
TAPE,WRAPPING TYPE,48mmx50M ROHS LE1915
TAPE,WRAPPING TYPE(VIEWSONIC),50mmx75M,L
TAPE,ACE,45mmx30M(PC=10x45mm),LE1709 ROH
LABEL,OPENING STAND, LE1709
LABEL,HI-POT PASS, LE1709
LABEL,CARTON(8ms),PRC, LE1709 For V7 Panel
LABEL,PRODUCT(2), LE1709
LABEL,ENERGY STAR, LE1709
FILM,PE 500mmx900M ROHS
LABEL,BLANK,76.2x76.2mm,LE1709(UPC)
LABEL,BLANK,50x25mm,LE1709(S/N)
LABEL,BLANK,210x65mm,LE1709(PALLET)
LABEL,BLANK,35x8mm, LE1709 ROHS For V7 Panel
BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RO
SCREW,I,CROSS,M3*4,Zw,ROHS
SCREW,P,CROSS,M5*22,Ni,ROHS
SCREW,PW,CROSS,W/WAS,M3*5,NI
SCREW,F,CROSS,T.T-4*10,Ni ROHS
SCREW,B,CROSS,T.T-4*10,BLK ,ROHS
CLIP,WIRE.CH-01P(PG), LE1709
LCD PANEL 17" MT170EN01-V7-G1,AM17000057
LCD PANEL 17" MT170EN01-V7-G2,AM17000057
LCD PANEL 17" MT170EN01-V7-G3,AM17000057
KIT,ACCESSORY,VA702-INL,LE1709
ASSY,BASE, LE1709
ASSY,BEZEL(S),LE1709
ASSY,BACK COVER, LE1709
ASSY,FIANL(S,V7/G1&2&3),LE1709-6A0
ASSY,PANEL(V7/G1&2&3),LE1709-6A0
PCBA,IF BOARD(V7), LE1709- 6A0 ROHS
PCBA,PWR&INV./B, LE1709-6A0 ROHS
PCBA,KEYPAD BOARD, LE1709 ROHS
44
Location
For VSI
For VSI
For VSI
For Singapore
For Australia
For TWN
For Korea
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
For VSI
Confidential - Do Not Copy
Universal number#
Q'ty (PC)
100
1
1
1
1
1
1
1
100
1
2
1
1
1
1
1
1
1
100
1
1
1
400
1
100
1
0.02778
0.0556
5.556
1
1
1
1
1
100
1.389
1
1.2
0.00513ROL
0.1
1
1
1
1
1
0.05
1
1
0.02778
2
2
100
4
9
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
VA702-1_VA702b-1
BOM LIST (VA702B-1)
ViewSonic Model Number: VS10781
Serial No. Prefix: PSX
Rev: 1b
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
ViewSonic P/N
CB-00005261
CB-00005260
CB-00005259
CB-00005254
A-00003675
A-00006679
A-00003671
A-00006733
A-00006734
N/A
N/A
C-00006088
N/A
N/A
N/A
N/A
N/A
HW-00005277
HW-00005276
N/A
N/A
N/A
N/A
N/A
N/A
P-00008079
N/A
N/A
N/A
P-00005257
P-00005253
N/A
N/A
N/A
P-00005272
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
HW-00005270
HW-00005271
HW-00005267
HW-00005269
HW-00005266
HW-00005265
N/A
E-00008006
E-00008007
E-00008008
N/A
C-00005262
C-00008095
C-00005264
N/A
N/A
B-00008066
B-00005279
B-00005278
Ref. P/N
430300100210R
430300800320R
430303000140R
453010100100R
453070800230R
453070800250R
453070800420R
453070800480R
453070800500R
501010202710R
501020202900R
501020203000R
501030201900R
501120101200R
501240201000R
502020300700R
502020300710R
502060401900R
502060401910R
502080300300R
502090301300R
502170300400R
503010001700R
503020002600R
505040202000R
506020006810R
506037003700R
506039001200R
506039002301R
506040005500R
506040005510R
506102000300R
506102000400R
506102000500R
506120300400R
506150001310R
506250005112R
506380001800R
506380002100R
506381000700R
506390000400R
506390000600R
506390210110R
506390500100R
506431000300R
506440002300R
506440002400R
506440002600R
506440003000R
509000000700R
509016304102R
509116822300R
509146305300R
509212610300R
509412610500R
511100001500R
631102071910R
631102071920R
631102071930R
703000000510R
714020002400R
714030002410R
714050002400R
71407276B101R
71408276B100R
790411300630R
790411400600R
790411500000R
ViewSonic Corporation
Description
HRN ASS'Y 1P 137mm BLACK,UL100 7 #20,RoHS
HRN ASS'Y 4x2P 189mm UL2651#28SZ504479B,
HRN LVDS FFC 30P 234mm,RoHSACCX30234KU28
CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40
PWRCORD 5A/250V BLK 6FT UK3Gx.75mm(SP60/
PWR CORD 10A/125V BLK 6FT UL/CSA,SVT 18x
PWRCORD 10A/250V BLACK 6FT SAA,H05W-F/3G
PWRCORD 7A/125V BLK 6FT CNS,VCTF 3Gx0.75
PWRCORD 16A/250V BLK 6FT KTL,H05VV-F 3Gx
BEZEL,FRONT(GRAY),VA702B,LE1709
COVER,BACK, LE1709
COVER,HINGE, LE1709
BUTTON,FUNCTION KEY, LE1709
LENS, LE1709
BASE, LE1709
BRACKET,LEFT, LE1709
BRACKET,RIGHT, LE1709
HINGE,LEFT, LE1709
HINGE,RIGHT, LE1709
SUPPORT,VESA, LE1709
CHASSIS, LE1709
PLATE,BASE,LE1709
RUBBER,SPACER,L25xW10xT4.0mm,LE1709
RUBBER,FOOT,OD14.1xT2.5mm,3M, LE1708
INSULATOR,MYLAR,L79.7xW62.7mm,CHASSIS, L
CARTON,VA702B, LE1709
CARDBOARD,COVER,L1120xW980xH120xT5mm,LE1
CORNER PAPER,820x50x50mm
CORNER PAPER,2050x50x50xT3mm,LE1705
CUSHION,EPS-L, LE1709
CUSHION,EPS-R, LE1709
LOGO PLATE,VIEWSONIC, LE1709
LOGO PLATE,VIEWSONIC, LE1709(THREE BIRDS)
LOGO PLATE,VIEWSONIC, LE1709(ELLIPSE)
BAG,PE+EPE,L590xW480xT0.6mm (PRINTED)LE1
PALLET,1120x980x120mm,LE1709
LBL,AGENCY(VA702B), LE1709(KOREA MARK)
TAPE,WRAPPING TYPE,48mmx50M LE1X04/05
TAPE,WRAPPING TYPE(VIEWSONIC),50mmx75M,L
TAPE,ACE,45mmx30M(PC=10x45mm),LE1709
LABEL,OPENING STAND, LE1709
LABEL,HI-POT PASS, LE1709
LABEL,CARTON(8ms),PRC, LE1709
LABEL,ENERGY STAR, LE1709
FILM,PE 500mmx900M
LABEL,BLANK,76.2x76.2mm,LE1709(UPC)
LABEL,BLANK,50x25mm,LE1709(S/N)
LABEL,BLANK,210x65mm,LE1709(PALLET)
LABEL,BLANK,35x8mm, LE1709 ROHS
BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RO
SCREW,I,CROSS,M3*4,Zw,ROHS
SCREW,P,CROSS,M5*22,Ni,ROHS
SCREW,PW,CROSS,W/WAS,M3*5,NI
SCREW,F,CROSS,T.T-4*10,Ni ROHS
SCREW,B,CROSS,T.T-4*10,BLK ,ROHS
CLIP,WIRE.CH-01P(PG), LE1709
LCD PANEL 17" MT170EN01-V7-G1,AM17000057
LCD PANEL 17" MT170EN01-V7-G2,AM17000057
LCD PANEL 17" MT170EN01-V7-G3,AM17000057
KIT,ACCESSORY,VA702B-INL,LE1709
ASSY,BASE, LE1709
ASSY,BEZEL(G),LE1709
ASSY,BACK COVER, LE1709
ASSY,FIANL(G,V7/G1&2&3),LE1709-6A0
ASSY,PANEL(V7/G1&2&3),LE1709-6A0
PCBA,IF BOARD(V7), LE1709- 6A0 ROHS
PCBA,PWR&INV./B, LE1709-6A0 ROHS
PCBA,KEYPAD BOARD, LE1709 ROHS
45
Location
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For Singapore
For VSA
For Australia
For TWN
For Korea
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
For VSI&VSA
Confidential - Do Not Copy
Universal number#
Q'ty (PC)
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
4
1
1
0.02778
0.0556
0.05556
1
1
1
1
1
1
0.01389
1
0.004ROL
0.00513ROL
0.001ROL
1
1
1
1
0.0004ROL
1
1
0.02778
2
2
4
4
9
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
VA702-1_VA702b-1
8. Exploded Diagram and Exploded Parts List
C
D
D
A
A
C
A
A
D
D
D
C
B
B
D
D
B
C
B
D
D
F
C
F
ViewSonic Corporation
E
E
E
ViewSonic Corporation
46
Confidential - Do Not Copy
VA702-1_VA702b-1
E
Model
Title
Date
Exploded diagram
Rev:
EXPLODED PARTS LIST (VA702-1)
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
ViewSonic Model Number: VS10781
Rev: 1a
ViewSonic P/N
C-00003154
E-00003048
B-00003041
CB-00003155
B-00003043
HW-00003156
B-00003172
CB-00003157
HW-00003158
HW-00003159
C-00003160
HW-00003161
B-00003042
CB-00003162
C-00003163
C-00003164
M-00003165
HW-00003166
HW-00003167
HW-00003168
HW-00003169
HW-00003170
M-00003171
Ref. P/N
714030002400
631102070270
790411300600
430303000140
790411400600
502020300700
502090301300
430300800320
502020300710
502060401900
714050002400
502060401910
790411500000
430300100190
714020002400
501020203000
505040202000
509412610500
509212610300
509016304102
509146305300
509116822300
509000000700
Description
ASSY,BEZEL(S),LE1709
LCD PANEL 17" MT170EN01-V1(INNOLUX)
PCBA,IF BOARD, LE1709-6A0
HRN LVDS FFC 30P 234mm,ACCX30234KU28MY
PCBA,PWR&INV./B, LE1709-6A0
BRACKET,LEFT, LE1709
CHASSIS, LE1709
HRN ASS'Y 4x2P 189mm UL2651#28SZ504479B
BRACKET,RIGHT, LE1709
HINGE,LEFT, LE1709
ASSY,BACK COVER, LE1709
HINGE,RIGHT, LE1709
PCBA,KEYPAD BOARD, LE1709
HRN ASS'Y 1P 157mm BLACK,UL1007#20
ASSY,BASE, LE1709
COVER,HINGE, LE1709
INSULATOR,MYLAR,L79.7xW62.7mm,CHASSIS, L (Chassis)
SCREW,B,CROSS,T.T-4*10,BLK (Back cover & Bezel)
SCREW,F,CROSS,T.T-4*10,Ni (Hinge & Back cover)
SCREW,I,CROSS,M3*4,Zw (chassis&bracket*4,GND*1)
SCREW,PW,CROSS W/WAS,M3*5,Ni (PCB&chassis*5, Bracket & Chassis*4)
SCREW,P,CROSS,M5*22,Ni (Hinge & Base ASM)
BOLT,#4-40x11.8,NiFOR D-SUB/DVI CONN. (D-SUB)
Q'ty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
4
4
5
9
4
2
EXPLODED PARTS LIST (VA702b-1)
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
ViewSonic Model Number: VS10781
Rev: 1a
ViewSonic P/N
C-00003173
E-00003048
B-00003041
CB-00003155
B-00003043
HW-00003156
B-00003172
CB-00003157
HW-00003158
HW-00003159
C-00003160
HW-00003161
B-00003042
CB-00003162
C-00003163
C-00003164
M-00003165
HW-00003166
HW-00003167
HW-00003168
HW-00003169
HW-00003170
HW-00003171
ViewSonic Corporation
Ref. P/N
714030002410
631102070270
790411300600
430303000140
790411400600
502020300700
502090301300
430300800320
502020300710
502060401900
714050002400
502060401910
790411500000
430300100190
714020002400
501020203000
505040202000
509412610500
509212610300
509016304102
509146305300
509116822300
509000000700
Description
ASSY,BEZEL(G),LE1709
LCD PANEL 17" MT170EN01-V1(INNOLUX)
PCBA,IF BOARD, LE1709-6A0
HRN LVDS FFC 30P 234mm,ACCX30234KU28MY
PCBA,PWR&INV./B, LE1709-6A0
BRACKET,LEFT, LE1709
CHASSIS, LE1709
HRN ASS'Y 4x2P 189mm
BRACKET,RIGHT, LE1709
HINGE,LEFT, LE1709
ASSY,BACK COVER, LE1709
HINGE,RIGHT, LE1709
PCBA,KEYPAD BOARD, LE1709
HRN ASS'Y 1P 157mm BLACK,UL1007#20
ASSY,BASE, LE1709
COVER,HINGE, LE1709
INSULATOR,MYLAR,L79.7xW62.7mm,CHASSIS, L (Chassis)
SCREW,B,CROSS,T.T-4*10,BLK (Back cover & Bezel)
SCREW,F,CROSS,T.T-4*10,Ni (Hinge & Back cover)
SCREW,I,CROSS,M3*4,Zw (chassis&bracket*4,GND*1)
SCREW,PW,CROSS W/WAS,M3*5,Ni (PCB&chassis*5, Bracket & Chassis*4)
SCREW,P,CROSS,M5*22,Ni (Hinge & Base ASM)
BOLT,#4-40x11.8,NiFOR D-SUB/DVI CONN. (D-SUB)
47
Confidential - Do Not Copy
Q'ty
VA702-1_VA702b-1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
4
4
5
9
4
2
9. Block Diagram
1
4
Lamp2
OZ9910
2
Open
Protection
3
4
Lamp4
2
1
Rectifier &
Filter Circuit
Power
Transformer
TOP246Y
OPP/OCP
LTV817
Feedback
OVP
5V
MCU
W78E65p
LDO
5V-3.3V
5V-1.8V
Panel Enable
On/Off
AP2301
PMBT3906
XTAL2
14.318MHz
Brightness
Panel Interface
Scaler
TSU16AK
VGA Connector
XTAL1
22.118MHz
Keypad
Connector
VGA Input
24C02
Keyboard
24C16
Block Diagram
5V
12V
Rectifier &
Filter Circuit
AC Line Filter
AC Socket
AC Input 90V-264V
Power
TFT LCD Panel 17"
MT170EN01(Innolux)
Lamp1
Transformer1
AOP605L
AOP605L
Transformer2
3
Lamp3
Brightness
VA702-1_VA702b-1
Confidential - Do Not Copy
48
ViewSonic Corporation
On/Off
10. Schematic Diagrams
C820
2200P Y1
C805
C807
100u 450V 33n 400V/ NC
ZD802
P6KE200A
R801
3M3
8
R824
510K
R822
3M3
D805 SRF5-04
F
3
1
R816
6R8
5
R817
12K
C813
47p 1KV
C818
47u/25V
C817
0.1u 50V
3
Q802
2SC1815
B801
BEAD CORE 3.5x9
C826
1000u 10V C814
47u 25V
R808
10K
IC801
LTV817
4
X
3
S
4
C806
2200P Y2
250V
R812
6R8
C
2
R829
200R
1
R827
10K
C822
0.1u 50V
ZD803
5.6V
ZD804
16V
6
C815
47u/25V
IC802
TOP246Y
R828
100R 1W
ZD801
9.1V
VCC5V
C812
1000u 10V
7
C810
220u 25V
L803
5uH 5A
2
4
2
1M
C804 0.47u X2
275V
C801
2200P Y2
250V
1
1
3
D806
A02
R825
470K
6
R820
C808
1000u 25V
C811
1n 500V
3
5
D
1M
+14V
RT801
5R
C824
4700P Y1
PGND
R809
100R
R810
5K1 1%
1
R815
1K
2
Q801
PMBT3904
R814
1K
R813
1K
R811
51K 1%
C816
0.1u 100V
MEB
C
1
1
D804
MUR1100
R823
3M3
R821
2
R806
10R
L
4
3
L802
5uH 5A
9
4
1
10
2
2
3
1
D803 SRF8-10
R807
510K
R805
3M3
L801
12mH
2
11
2
3
1
T801
TRF-EI28
R803
510K
C803
4n7/1KV
-
2
400V
C802
1n 500V
D809
1N4148W
2
+ 1
D801
BL4-06
R804
68R 1/2W
R802
10R
C819
47u/25V
A
R
IC803
TL431
R819
10K
R818
3K3 1%
F801
2A 250V
1
2
N
L
CN801
08DA-6S
1
2
3
4
5
6
3
P801
AC IN
TO SCALER BD CN101
VCC5V
BRIGHTNESS
ON/OFF
C821
0.1u/50V
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
Confidential - Do Not Copy
49
VA702-1_VA702b-1
POWER SUPPLY
Rev:
+14V
H
C511
2.2uF/25V
C522
220uF/25V
R501
3M/3kv
+
T501
EEL-19 22:2600
2
D513 SKS20-04AT
2
1
IC501
R528
182K 1%
R522
91K 1%
4
5
C529
220P/50V
6
7
BRIGHTNESS
R524
51K 1%
8
C504
1n/50V
15
PDRV1
PGND
3
R523
100K 1%
PDRV2
NDRV2
2
16
NDRV1
HSB
GNDA
VIN
CT
V5000
LCT
ISEN
DIM
CMP_SST
ENA
VSEN
C528
1.0u/25V
14
CN502
8
7
6
5
D1
D1
D2
D2
6
H
7
C527
5P/3KV
3
C530
6.8n/50V
+5V
12
11
C503
100n/50V
10
9
OVP1
2
D507
1 BAV99
R505
1M
D1
D1
D2
D2
1
8
7
6
5
2
D514
SKS20-04AT
+
C509
220uF/25V
S1
G1
S2
G2
D501
BAV99
IS3
R513
510 1%
8
H
R503
3M/3KV
5
3
7
3
R506
3.9K 1%
D503
1 BAV99
C508
22n/25V
R504
3.9K
C526
10P/3KV
IS3
CN503
OP2
R510
1k
CN501
H
510Ω
510Ω
560Ω
510Ω
510Ω
560Ω
R524
51KΩ
47KΩ
47KΩ
Q505
2
Q504
2N7002
3
C531
2
2
0.1u/50V
0.1u/50V
R521
1M
R519
1M
D512
1N4148W
Q502
2N7002
3
C532
2
5V
3
C536
NC
2
D505
1 BAV99
OP1
IS1
R509 510 1%
100K
R508
D510
1N4148W
D509
1N4148W
OP1
Confidential - Do Not Copy
VA702-1_VA702b-1
1
R515
1M
OP2
OP4
50
2
D502
BAV99
R514 510 1%
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
L
OVP2
0.1u/50V
R517
1M
D511
1N4148W
2N7002
3
C533
0.1u/50V
OP3
NOTE:
紅色粗線:表示高電壓迴路;
紅色虛線:表示易發熱元件;
橘色粗線:表示大電流迴路;
Q503
2N7002
3
C534
1
R511
C523
6.8n/50V
1
R509
C525
5P/3KV
2N7002
3
3
1
INL
1
QDI
D504
1 BAV99
2
R507
3.9K 1%
2
1
AUO
L
2
Q501
Item
1
R511
510 1%
3
6
2
C535
NC
T502
EEL-19 22:2600
2
L
3
OVP1
IS1
OVP2
C507
2200p/50V
U502
AOP605
1
2
3
4
C502
2.2u/25v
5V
C506
4700P/50V
R512
1k
OP3
R527
3.3M 1%
C505
0.01u/25V
OP4
13
47K 1%
R526
R529
1M
3
D506
1 BAV99
2
R502
3.9K
AOP605
OZ9910G
ON/OFF
S1
G1
S2
G2
D508
1 BAV99
5
U501
1
2
3
4
8
C524
10P/3KV
L
CN504
2
3
5V
1
3
INVERTER
Rev:
U102
FS8860-33PJ
VCC5V
VAA1
ADJ
VOUT
C102
0.1/50V
+
C103
100uF/16V
1
+
VIN
VCC3.3
2
VAA2
C104
0.1/50V
VAA3
VAA4
VAA1
VAA2
VAA3
VAA4
R174
9.1R/2W
U101
FS8860-18PJ
VIN
VOUT
2
VCC5V
1
2
3
4
5
6
BRIGHTNESS
ON/OFF
C111
0.1/50V
+ C101
100uF/16V
VCC1.8
+
C106
100uF/16V
1
+
CN101
4500-06
VCC1.8
ADJ
3
C105
100uF/16V/NC
VCC3.3
From Power &
Inverter
C169
100uF/16V
3
C107
0.1/50V
R104
4K7
BRIGHTNESS
DIMMER1
C113
1u/16V
VCC5V
Q101
S
R101
10K
C108
0.1/50V
R103
4K7
R169
22K
VLCD
ON/OFF
R105
4K7
R106
10K
VCC5V
G
R170
0
Q102
PMBT3906
PANEL_ENABLE
VLCD
AP2301N
D
+
C109
100uF/16V
Q107
PMBT3904
C110
0.1/50V
C114
0.1/50V
CCFL_ENABLE
R157
Q103
PMBT3904 4K7
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
51
Confidential - Do Not Copy
VA702-1_VA702b-1
DC INPUT
Rev:
16
PC5V_VGA
11
1
6
2
7
3
8
4
9
5
10
12
13
14
R166
0
VGA_G
R167
0
VGA_B
R168
0
R112
75 1%
R113
75 1%
R115
R121
R116
R122
R117
R123
R118/NC
22
47
22
47
22
47
470
C115
C121
C116
C122
C117
C123
NC/C118
47n/25V
47n/25V
47n/25V
47n/25V
47n/25V
47n/25V
1000P/50V
R114
10K
R107
100
RIN
GNDR
GIN
GNDG
BIN
GNDB
SOG
VCC5V
TVS101
BAV99
17
15
VGA_R
R111
75 1%
CN102
DZ11AA1-HW6
TVS102
BAV99
C165
NC
C166
NC
C167
NC
TVS103
BAV99
HPD_VGA
DDC_SCL_VGA
DDC_SDA_VGA
R110
100
R108
1K
HSI
R165
0
R109
1K
DDC_SDA_VGA
R127
R126
R125
R124
DDC_SCL_VGA
PC5V_VGA
VCC5V
TVS105
5V6
DET_VGA
DDC_SCL_VGA
DDC_SDA_VGA
VSI
TVS104
5V6
VCC5V
TVS106
5V6
TVS107
5V6
R119
2K2
C119
33p/50V
R120
2K2
VSYNC
HSYNC
C120
220p/50V
100
100
10K
10K
D103
SN4148
D104
SN4148
C124
0.1/50V
1
2
3
4
U103
AT24C02N-10SI
A0
A1
A2
GND
VCC
WP
SCL
SDA
8
7
6
5
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
52
Confidential - Do Not Copy
VA702-1_VA702b-1
VGA_INPUT
Rev:
VAD
VPLL VDVI VDPLL
VPO
VCC3.3
VDD
VPO
C125
1u/16V
66
67
73
74
DIMMER1
18
87
97
117
VDDC
VDDC
VDDC
VDDC
11
21
84
94
104
114
126
53
AVDD_PLL
35
45
51
AVDD_DVI
AVDD_DVI
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
NC/LVB3P
NC/LVB3M
NC/LVBCKP
NC/LVBCKM
NC/LVB2P
NC/LVB2M
NC/LVB1P
NC/LVB1M
NC/LVB0P
NC/LVB0M
U104
TSU16AK
AD0/GPO6
AD1
AD2
AD3/GPO5
REFP
REFM
CSZ
SCL
SDA
HWRESETZ
INT
PWM0
PWM1
BYPASS
19
GNDC
86
GNDC
96
116 GNDC
GNDC
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
BUS TYPE/NC
10
20
85
95
105
115
127
XOUT
AVSS_DVI
AVSS_DVI
AVSS_DVI
34
XIN
39
42
48
C168
22p/50V
33
AVSS
AVSS
AVSS
AVSS_MPLL
AVSS_PLL
X102
14.318MHz
AVSS_LPLL
68
56
64
36
54
C126
22p/50V
102
103
106
107
108
109
110
111
112
113
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PA8
PA9
118
119
120
121
122
123
124
125
128
1
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
PA[0..9]
C129
C130
C131
C132
C133
C170
C171
0.1/50V 0.1/50V 0.1/50V 0.1/50V 0.1/50V 0.1/50V 0.1/50V
VCC1.8
PA[0..9]
VDD
VCC1.8
FB103
BEAD60OHM
C134
10u/16V
VAA1
PB[0..9]
VAA1
PB[0..9]
FB104
BEAD60OHM
VAA2
30
77
78
31
AD0
AD1
AD2
AD3
69
71
70
32
72
R164
R163
R162
3
CSZ/ALE
SCL/RDZ
SDA/WRZ
HWRESET
INT
1K
1K
1K
VPLL
FB105
BEAD60OHM
C140
10u/16V
VAA3
C141
0.1/50V
VDVI
VAA3
FB106
BEAD60OHM
2
R129
C139
C173
0.1/50V 0.1/50V
VAA2
C127 0.1/50V
6
C135
C136
C137
C172
0.1/50V 0.1/50V 0.1/50V 0.1/50V
VAD
C138
10u/16V
C162 100p/50V
390 1%
R+
RG+
GB+
BCK+
CKREXT
LVA3P
LVA3M
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
C128
10u/16V
C163 100p/50V
R128
RIN0
RIN0M
GIN0
GIN0M
SOGIN0
BIN0
BIN0M
HSYNC0
VSYNC0
DDC1_CLK/GPO8
DDC1_DAT/GPO7
FB102
BEAD60OHM
C164 100p/50V
VDVI
40
41
43
44
46
47
49
50
52
AVDD_MPLL
63
62
60
59
61
58
57
37
38
29
28
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSYNC
VSYNC
AVDD
AVDD
55
65
VCC3.3
4K7
C142
10u/16V
VCC3.3
VAA4
C143
C174
0.1/50V 0.1/50V
VDPLL
VAA4
FB107
BEAD60OHM
C144
10u/16V
C145
0.1/50V
Note: U104 pin4,5,7~9,12~17,22~27,75,76,79~83,88~93,98~101 are all NC (open)
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
53
Confidential - Do Not Copy
VA702-1_VA702b-1
SCALER
Rev:
CN103
AL2309-A0G1Z
PB[0..9]
PA[0..9]
PB9
PB8
PB7
PB6
PB5
PB4
RXO0RXO0+
RXO1RXO1+
RXO2RXO2+
PB3
PB2
PB1
PB0
PA9
PA8
RXOCRXOC+
RXO3RXO3+
RXE0RXE0+
PA7
PA6
RXE1RXE1+
PA5
PA4
PA3
PA2
PA1
PA0
RXE2RXE2+
RXECRXEC+
RXE3RXE3+
VLCD
VLCD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CN104
DUPON2.0mm/NC
RXO0RXO1RXO2RXOCRXO3RXE0RXE1RXE2RXECRXE3VLCD
24
22
20
18
16
14
12
10
8
6
4
2
23
21
19
17
15
13
11
9
7
5
3
1
RXO0+
RXO1+
RXO2+
RXOC+
RXO3+
RXE0+
RXE1+
RXE2+
RXEC+
RXE3+
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
54
Confidential - Do Not Copy
VA702-1_VA702b-1
PANEL INTERFACE
Rev:
RP101
10K
VCPU
1
2
3
4
8
9
23
33
34
RP104
10K
8
7
6
5
2
3
4
5
6
7
PANEL_ENABLE
CCFL_ENABLE
DET_VGA
VCPU
Q104
PMBT3906
LED_GREEN
R158
51
R143
4K7
R144
4K7
1
P3.4/T0
P3.5/T1
P3.6/WR
VCPU
R145
220
4
3
2
1
4
3
2
1
5
6
7
8
10K
P3.7
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P3.3/INT1
P4.2
C154
12p/50V
5
6
7
8
5
6
7
8
4
3
2
1
R134
44
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P1.6/PWM3
P1.7/PWM4
P4.0
ALE
P4.1
20
R142
220
C153
NC/10u/16V
P4.3/INT2
P3.1/TXD
P3.0/RXD
VSS
43
42
41
40
39
38
37
36
12
HWRESET
CSZ/ALE
SCL/RDZ
SDA/WRZ
AD0
AD1
AD2
AD3
ISP for Standard
8051
24
25
26
27
28
29
19
15
13
11
22
R146
R147
R148
R149
R150
1K
1K
1K
1K
1K
LED_GREEN
LED_ORANGE
KEY_POWER
KEY_SELECT/AUTO
KEY_UP
KEY_DOWN
KEY_MENU/EXIT
6
8
4
1
3
5
2
7
CN106
2x4PIN
VCPU
R156
10K
TO KEY PAD
16
17
18
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
1000P/50V
1000P/50V
1000P/50V
1000P/50V
1000P/50V
U106
24C16
C151
0.1/50V
100
100
RP103
10K
C156
C157
C158
C159
C160
R140
R141
PSEN
X1
8
7
6
5
VCC
WP
SCL
SDA
R139
10K
RP102
10K
R155
10K
R153
R152
100
100
DDC_SDA_VGA
DDC_SCL_VGA
21
A0
A1
A2
GND
R138
10K
RST
P3.2/INT0
X2
1
2
3
4
32
R137
10K
VDD
10K
31 R133
EA
INT
VCPU
D102
SN4148
10
14
P2.7
U105
Winbond W78E65P
C150
10u/16V
10K
VCPU
30 R132
C149
0.1/50V
C148
10u/16V
P2.6
FB108
BEAD60OHM
0
VCPU
35 R131
VCC5V
X101
22.1184MHz
C155
12p/50V
Q105
PMBT3906
LED_ORANGE
ViewSonic Corporation
R159
220
Model
Title
Date
ViewSonic Corporation
55
Confidential - Do Not Copy
VA702-1_VA702b-1
MCU
Rev:
LED101
GREEN
LED_GREEN
LED_ORANGE
KEY_MENU/EXIT
KEY_SELECT/AUTO
KEY_POWER
KEY_DOWN
KEY_UP
ORANGE
SW101
SW102
SW103
SW104
6
8
2
1
4
5
3
7
SW105
CN106
2x4PIN
SW TACT
SW TACT
SW TACT
MENU/1
AUTO/2
POWER
SW TACT
DOWN
SW TACT
UP
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
56
Confidential - Do Not Copy
VA702-1_VA702b-1
KEYPAD
Rev:
11. PCB Layout Diagrams
Main board Top layout
ViewSonic Corporation
57
Confidential - Do Not Copy
VA702-1_VA702b-1
Main board bottom Layout
ViewSonic Corporation
58
Confidential - Do Not Copy
VA702-1_VA702b-1
POWER board
ViewSonic Corporation
Confidential - Do Not Copy
59
VA702-1_VA702b-1
ViewSonic Corporation
60
Confidential - Do Not Copy
VA702-1_VA702b-1
* Reader’s Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
Unit
Excellent
Good
Fair
Bad
1. Precautions and Safety Notices
2. Specification
3. Front Panel Function Control Description
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram and Exploded Parts List
9. Block Diagrams
10. Schematic Diagrams
11.PCB Layout Diagrams
B. Are you satisfied with this Service Manual?
Item
Excellent
Good
Fair
Bad
1. Service Manual Content
2. Service Manual Layout
3. The form and listing
C. Do you have any other opinions or suggestions regarding this service manual?
Reader’s basic dada:
Name:
Title:
Company:
Add:
Tel:
Fax:
E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile
1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes
([email protected])
ViewSonic Corporation
61
Confidential - Do Not Copy
VA702-1_VA702b-1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement