TH106 User Guide n Programmable Thermostat

TH106 User Guide n Programmable Thermostat
TH106
User Guide
Programmable Thermostat
NOTE: Always keep the thermostat's vents clean and unobstructed.
Temperature
preset buttons
n
Appears when the
setpoint is displayed
Time and day
Temperature
Set the day
Set the time
Operating
mode icons
Program the
schedule
Temperature
preset icons
Skip a period
Heating power
indicator
Select the
operating mode
o
Periods
Connect the thermostat wires to the line wires and to the load
wires using solderless connectors for copper wires.
Temperature
adjustment
buttons
n
Description
1.
2-wire installation
This programmable thermostat can be used to control an electric
heating system such as an electric baseboard heater, a radiant ceiling, a radiant floor, a convector, etc.
The thermostat cannot be used under the following conditions:
•
•
•
•
The resistive load is greater than 16.7 A
The resistive load is less than 2 A
The system is driven by a contactor or relay (inductive load)
The system is a central heating system
4-wire installation
SUPPLIED PARTS:
•
One (1) thermostat
•
Two (2) 6-32 screws
•
Two (2) solderless connectors
o
Installation
2.
TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN
POWER PANEL TO AVOID ELECTRICAL SHOCK.
THE INSTALLATION MUST BE PERFORMED BY AN ELECTRICIAN.
All cables and connections must conform to the local electrical
code.
Special CO/ALR solderless connectors must be used when connecting with aluminum conductors.
Install the thermostat onto an electrical box.
Install the thermostat about 5 feet high, on an inside wall facing
the heater.
Avoid locations where there are air drafts (such as the top of a
staircase or an air outlet), dead air spots (such as behind a
door), or direct sunlight.
Do not install the thermostat on a wall that conceals chimney or
stove pipes.
p
Push any excess wire back into the electrical box.
NOTE: If necessary, before re-installing the front component, configure the thermostat (see section 3).
q
Return power to heating system.
The thermostat wires are not polarized; either wire can be connected to the load or to the power supply.
TH106
400-106-001-D
12/8/05
1/3
p
3.
Configuration
The configuration switches are on the back of
the thermostat. The factory settings are indicated by the gray cells in the following table.
SW1
SW2
SW3
SW4
a
Early Start
Temperature / time format b
Cycle length
Not used
c
s
Off
On
°C / 24-hour
°F / 12-hour
15 seconds
-
15 minutes
-
a. Early Start can be used in Automatic mode only. When this function is enabled, the thermostat calculates the optimal time to start
heating in order to obtain the desired temperature by the set time.
The thermostat re-assesses the start time daily based on the previous day’s performance.
b. If you change the temperature display format, the preset
temperatures ( , and ) will return to their default settings.
c. 15-second cycles should be selected in most cases as it provides
better temperature control. 15-minute cycles must be selected if
you have a fan-equipped heater or if 15-second cycles causes
light flickering (especially in rural regions).
q
4.
Power-up
Upon power-up, the thermostat is in manual mode ( ) and displays
the actual (ambient) temperature.
n
o
Automatic - The temperature is set according to the programmed
schedule. To place the thermostat in this mode, press Mode until
is displayed. The icons of the current period and preset temperature
are also displayed.
Temporary Bypass: If you modify the setpoint (by pressing the
, ,
or button) when the thermostat is in automatic
mode, the new setpoint will be used until the end of the current
period. When the next period starts, the temperature set for that
period becomes the new setpoint.
Manual - The programmed schedule is not used. The temperature
must be set manually. To place the thermostat in this mode:
n
o
Press Mode until
is displayed.
Set the temperature using the
t
,
,
or
button.
7.
Schedule
The schedule consists of 4 periods per day which represents a typical weekday. You can program the thermostat to skip the periods that
do not apply to your situation. For example, you can skip periods 2
and 3 for the weekend.
Description
Press the Day button to set the day.
Associated temperature preset
Wake
5.
Temperature Setting
Setpoint
The thermostat normally displays the actual temperature. To view the
setpoint, press the
or button briefly. The setpoint will appear for
the next 5 seconds.
To change the setpoint, press the
or
button until the desired
temperature is displayed. To scroll faster, hold the button.
Using a preset temperature
The thermostat has 3 preset temperatures:
Comfort temperature
Economy temperature
Vacation temperature
Leave
Return
Sleep
The Comfort ( ) temperature is used in periods 1 and 3 and the
Economy ( ) temperature is used in periods 2 and 4. For example,
when the period changes from 1 to 2, the setpoint automatically
changes from Comfort setting ( ) to Economy setting ( ).
You can have a different program for each day of the week; i.e., each
period can start at different time for each day of the week. The
thermostat has been programmed with the following schedule.
MO
TU
WE
TH
FR
SA
SU
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
16.5°C (62°F)
8:00
AM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
--:--
--:--
10°C (50°F)
6:00
PM
6:00
PM
6:00
PM
6:00
PM
6:00
PM
--:--
--:--
To use the Comfort or Economy temperature, press the
or
button respectively. The corresponding icon will be displayed.
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
Period
Icon
Intended use
Comfort (when at home)
Economy (when asleep or away from home)
Vacation (during prolonged absence)
•
6.
Operating Modes
Period
Press the Hour and Min buttons to set the thermostat’s clock.
r
To store the Vacation temperature:
Set the desired temperature using the or button. Press and
hold both
and buttons simultaneously for approximately 3
seconds until the
icon is displayed. Press the Mode button.
•
Factory setting
21°C (70°F)
To use the Vacation temperature, press both
and
buttons
simultaneously. The
icon will be displayed.
Storing a preset temperature
To store the Comfort or Economy temperature:
Set the desired temperature using the or button. Press and
hold the appropriate button ( or ) for approximately 3 seconds until the corresponding icon is displayed. Press the Mode
button.
TH106
Setting
To modify the schedule:
n
Press Pgm to access the programming mode. Period 1 is
selected.
o
Press Day to select the day to program (hold for 3 seconds to
select the entire week).
p
Press Hour and Min to set the start time of the selected period,
or press Clear if you want to skip the period (--:-- is displayed).
Press Pgm to select another period, or press Day to select
another day. Then repeat step 3.
q
400-106-001-D
12/8/05
2/3
r
Press Mode to exit the programming mode.
NOTE: If no button is pressed for 60 seconds, the thermostat will
automatically exit the programming mode.
u
8.
Power Outage
During a power outage, the settings are stored in memory. However,
only the thermostat’s clock must be re-adjusted if the power failure
lasts more than 2 hours. When power comes back, the thermostat
will return to the operating mode that was active prior to the power
failure.
v
9.
Troubleshooting
PROBLEM
Thermostat is hot.
Heater is always On.
Thermostat indicates
that heating is On, but
the heater is not On.
SOLUTIONS
This condition is normal. Under normal
operation, the thermostat housing can
reach a temperature between 35°C (95°F)
and 40°C (104°F).
The thermostat has not been correctly
wired.
The thermostat has not been correctly
wired.
The thermostat is exposed to air draft.
Eliminate the draft.
The sticker on the thermostat’s screen has
not been removed.
The thermostat was without power for
Wrong time is displayed.
more than 2 hours.
Check that the thermostat is in Automatic
Temperature does not
change according to the mode. Check the schedule and clock setprogrammed schedule. tings.
The thermal protection device on the
Display disappears and
heater is open. This can happen after a
reappears after a few
power failure or if the heater is obstructed
minutes.
by furniture or curtains.
The heating system is less than the
Display looks faded
when heating is actirequired minimum load. This thermostat
vated
cannot be used below that rating.
Wrong temperature is
displayed.
w
Technical Specifications
Power: 120/240 VAC, 50/60 Hz
Minimum load: 2 A (resistive only)
500 W @ 240 VAC
250 W @ 120 VAC
Maximum load: 16.7 A (resistive only)
2000 W @ 120 VAC
4000 W @ 240 VAC
Display range: 0°C to 60°C (32°F to 140°F)
Display resolution: 0.5°C (1°F)
Setpoint range: 5°C to 30°C (40°F to 86°F)
Setpoint interval: 0.5°C (1°F)
Storage: -20°C to 50°C (-4°F to 120°F)
Approval: c UL us
TH106
10.
;
11.
Warranty
Aube warrants this product, excluding battery, to be free from defects
in the workmanship or materials, under normal use and service, for a
period of three (3) years from the date of purchase by the consumer.
If at any time during the warranty period the product is determined to
be defective or malfunctions, Aube shall repair or replace it (at Aube's
option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to
the place from which you purchased it, or
(ii) contact Aube. Aube will make the determination whether the
product should be returned, or whether a replacement product can
be sent to you.
This warranty does not cover removal or reinstallation costs. This
warranty shall not apply if it is shown by Aube that the defect or malfunction was caused by damage which occurred while the product
was in the possession of a consumer.
Aube's sole responsibility shall be to repair or replace the product
within the terms stated above. AUBE SHALL NOT BE LIABLE FOR
ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF
THIS PRODUCT. Some provinces and states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE
MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS
HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS
WARRANTY. Some provinces and states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not
apply to you.
This warranty gives you specific legal rights, and you may have other
rights which vary from province or state to another.
12.
Customer Assistance
If you have any questions about the product installation or operation,
or concerning the warranty, contact us at:
705 Montrichard
Saint-Jean-sur-Richelieu, Quebec
J2X 5K8
Canada
Tel.: (450) 358-4600
Toll-free: 1-800-831-AUBE
Fax: (450) 358-4650
Email: [email protected]
For more information on our products, go to
www.aubetech.com
®
As an ENERGY STAR partner, Aube Technologies has
determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
400-106-001-D
12/8/05
3/3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement