SSM110
Pub. DSSSM110
G AI -T RO NI CS® CO RPO R AT I O N
A HU BBE LL C OM P ANY
SSM110 Card Rack Assembly
General Information
This data sheet applies to the SSM110 Card Rack Assembly, which is a central control device designed to
control a single-zone SmartSeries system and up to eight access panels. This system configuration
provides health checking (supervision) for the system’s page line and party line 1 cable, handset/speaker
amplifiers, and speakers and access panels.
SmartSeries handset stations and access panels allow page and party line communications throughout the
system. Additionally, two-way (telephone type) conversation can occur between stations on a party line.
Single party line systems and five party line systems are available. Refer to Figure 1 for typical system
diagram.
Figure 1. Typical SSM110 System Diagram
Capacities/Limitations
SmartSeries Stations—A maximum of 200 SmartSeries stations may be connected to the SSM110’s PPI
card.
Access Panels—A maximum of eight access panels may be connected to the API card of the SSM110
Card Rack.
Speakers—Only one speaker can be connected to a SmartSeries station if the station is supervising the
speaker. If speaker supervision is not being used, up to four speakers can be connected to a single station
in low noise areas.
Access Panel Cable—The recommended maximum cable distance from the card rack to an access panel
is 6,560 feet (2000 meters).
GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA
610-777-1374 „ 800-492-1212 „ Fax: 610-796-5954
VISIT WWW .GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
SSM110 Card Rack Assembly
Pub. DSSSM110
Page: 2 of 2
GAI-Tronics System Cable—The recommended maximum cable distance from the card rack to a
SmartSeries station is 5,250 feet (1600 meters).
GAI-Tronics Speaker Cable—The recommended maximum cable distance from a SmartSeries station
to an 8-ohm speaker is 75 feet (22.86 meters). The maximum cable distance from a SmartSeries station to
a 16-ohm speaker is 150 feet (45.72 meters).
Master Control Unit (MCU)—Contains the central processing that coordinates all operations as defined
by its software configuration file. The MCU maintains communication with all other cards in the card
rack and with SmartSeries devices located throughout the system.
Page/Party® Interface (PPI)—Interfaces SmartSeries and Page/Party® stations to the system. Each PPI
card supports up to 200 SmartSeries stations and an unlimited number Page/Party® stations.
Access Panel Interface (API)—Interfaces the access panels to the system. The API card supports up to
eight access panels.
Optional Ancillary Equipment
The optional equipment discussed below can expand the standard features of the SSM110 Card Rack:
The Model 10959-103 Audio Messenger Interface (AMI) tone/speech generator broadcasts live pages,
pre-recorded alarm tones, and pre-recorded speech messages. The included Audio Messenger Interface
Configuration Tool (ACT) software is used to configure the AMI. The AMI includes eight configurable
inputs and outputs. Typically, the inputs are configured to activate alarm/process tones and/or prerecorded speech messages, mute audio playback, and reset alarms. The outputs are generally used to
activate remote alarm systems, interface to automated processes, interface to paging equipment, etc.
The AMI provides the ability to perform live speech pages from a telephone when the AMI must be
connected to an analog station port of a PBX type telephone system, or directly to a Central Office
telephone line on the public switched telephone network (PSTN). The AMI includes a built-in feedback
eliminator.
The Model 10959-103 includes a Page/Party® system interface card. This interface card provides the
capability to broadcast any audio generated by the AMI on a GAI-Tronics Page/Party® system. When
coupled with a telephone interface card, the Page/Party® card provides telephone callers access to fullduplex line communications. AMI models that include the 33-ohm Page/Party® interface card allow a
telephone caller to direct the telephone call to a specific party line.
The Model 10434-202NA Building Entrance Protection Barrier provides secondary protection
from signal line transients and over-voltage conditions.
Specifications
Power supply............................................................................ Fused at 2 A, 250 V (not user-serviceable)
Input voltage ............................................................................................................... 120 V ac/240 V ac
Total power consumed......................................................................................... 50 VA, 25 W maximum
Input frequency range ................................................................................................................ 50/60 Hz
Input surge current (cold start)....................................................................Less than 25 A peak maximum
AC input power connector (side) .............................................................................. IEC 320-style, 3-pin
Temperature operating ....................................................................... +32° F to +122° F (0° C to +50° C)
Temperature storage ....................................................................................................... -40° C to +85° C
Relative humidity ................................................................................................ Non-condensing, 5–85%
Unit dimensions .................................... 10.47 H × 8.55 W × 12.34 D inches (265.9 × 217.2 × 313.5 mm)
Unit weight ................................................................................................................... 10 lbs. maximum
\\s_eng\gtcproddocs\standard ioms - current release\data sheets\dsssm110.doc
07/07
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement