RT3 Trip-Edge w/SmartHitch2 Installation Manual

RT3 Trip-Edge w/SmartHitch2 Installation Manual
BOSS PRODUCTS
A Division of Northern Star Industries, Inc.
P.O. Box 787 Iron Mountain MI 49801-0787
www.bossplow.com
RT3 TRIPEDGE SNOWPLOW
INSTALLATION MANUAL
TABLE OF CONTENTS
WARNINGS ................................................................................................................................................................ 2
SNOWPLOW MOUNTING & REMOVAL PROCEDURE ........................................................................................... 3
SNOWPLOW ASSEMBLY PROCEDURE ................................................................................................................. 4
TM
SMARTHITCH2 INSTALLATION PROCEDURE…………………………………………………………………………8
ELECTRICAL SYSTEM WIRING PROCEDURE ....................................................................................................... 10
HEADLIGHT ADAPTER INSTALLATION PROCEDURE .......................................................................................... 15
ELECTRICAL SYSTEM WIRING DIAGRAM ............................................................................................................. 16
ELECTRICAL SYSTEM WIRING SCHEMATIC (PLOW SIDE) ................................................................................. 17
ELECTRICAL SYSTEM WIRING SCHEMATIC (TRUCK SIDE) ............................................................................... 18
RT3 STRAIGHT BLADE MANIFOLD WIRING DIAGRAMS ...................................................................................... 19
HYDRAULIC POWER UNIT FILL PROCEDURE ...................................................................................................... 20
HEADLIGHT AIMING PROCEDURE ......................................................................................................................... 21
HYDRAULIC VALVE ASSEMBLY PARTS LIST ........................................................................................................ 22
STRAIGHT BLADE CONTROLLERS ........................................................................................................................ 23
TROUBLESHOOTING GUIDE ................................................................................................................................... 27
RECOMMENDED PUSH BEAM HEIGHT ................................................................................................................. 32
RECOMMENDED BOLT TORQUE ........................................................................................................................... 32
BOSS PRODUCTS / Northern Star Industries, Inc. reserves the right under its continuous product improvement policy to change construction or
design details and furnish equipment when so altered without reference to illustrations or specifications used herein.
This product is covered under one or more of the following patents:
5,568,694 4,074,448 4,658,519 6,108,946 6,170,178 6,134,814
Other Patents Pending
DRIVEN TO BE THE BEST
TRP07882-11
WARNING
Many newer trucks are equipped with air bags. DO NOT under any circumstances disable or remove or
relocate any sensors or other components related to the operation of the air bags.
WARNING
Always follow the vehicle manufacturer’s recommendations relating to snowplow installation. For
recommended vehicle models refer to the BOSS Snowplow Application Chart and Selection Guide.
WARNING
Vehicles equipped with air bags are designed such that the air bags will be activated in a frontal collision
equivalent to hitting a solid barrier (such as a wall) at approximately 14 mph or more, or, roughly speaking,
a frontal perpendicular collision with a parked car or truck of similar size at approximately 28 mph or more.
Careless or high speed driving while plowing snow, which results in vehicle decelerations equivalent to or
greater than the air bag deployment threshold described above, would deploy the air bag.
WARNING
Read this manual carefully before operating this snowplow.
WARNING
When transporting, position plow so as not to block vision or plow headlights.
WARNING
DO NOT change blade position when traveling.
WARNING
DO NOT exceed 40 mph when transporting plow.
WARNING
DO NOT exceed 14 mph when plowing.
WARNING
Always lower blade when vehicle is not in use.
WARNING
Make sure plow is properly attached before moving vehicle.
WARNING
To comply with Federal Regulations and to assure a safe vehicle, the Front Gross Axle Weight Rating
(FGAWR), Rear Gross Axle Weight Rating (RGAWR), and the Gross Vehicle Weight Rating (GAWR) must
not be exceeded at any time.
WARNING
Due to the variety of equipment that can be installed on this vehicle, it is necessary to verify that the Front
Gross Axle Weight Rating (FGAWR), Rear Gross Axle Weight Rating (RGAWR), and the Gross Vehicle
Weight Rating (GAWR) are not exceeded at any time. This may require weighing the vehicle and adding
ballast as necessary. It may also limit payload capacity of the vehicle. It is the operator’s responsibility to
verify that these ratings are not exceeded.
2
Snowplow Mounting Procedure
Figure 1. Mounting Procedures
MSC04607
3
Snowplow Assembly Procedure
3. Install Pushframe Attachment Bar (3) into the
pockets on Blade Assembly (4) using ten ¾”-10x2”
Hex Head Cap Screws (92) and ten ¾” Locking
Nuts (108).
Snowplow Assembly
Procedure
Note: This manual is used for the assembly of all
BOSS Trip-Edge Plows. Part numbers and
illustrations may vary.
1. Place Plow Blade on the ground face down.
Figure 4. Install Pushframe and Kickstand.
Figure 2. Install Shoe Assembly
4. Install Pushframe (2) into Pushframe Attachment
Bar (3) using 1”-8x7” Hex Head Cap Screw (86)
and 1”-8 Locking Nut (110).
2. Install TRP07880 Plow Shoe Assembly (12).
Mount Plow Shoes (12B) on Blade Assembly
(4) using 1” Flat Washers (12C) above and
below the base angle. Secure with 7/16” Quick
Pins (12A)
5. Pull the Kickstand Spring Pin (102B) outward then
insert STB03220 Kickstand Leg (11) through the
kickstand mount bracket. Release the Kickstand
Spring Pin (102B) to lock Kickstand Leg (11) in
place.
Note: Adjustment of Plow Shoe (12B) may be
necessary after mounting the plow on to the vehicle.
Figure 5. Install Angle Cylinders
Figure 3. Install Pushframe Attachment Bar
G10086
G10084
G10087
6. Install both Angle Cylinders (40) using the 5/8”11x4” Hex Head Cap Screw (85) and 5/8”-11
Locking Nuts (111). Make sure the hydraulic inlet
port is facing upward.
G10085
4
Snowplow Assembly Procedure
Note: Do not over tighten angle cylinder mounting
bolts. Mounting bolts should allow angle cylinder to
move vertically in mounting bracket.
Figure 7. Hydraulic Connections
Figure 6. Lift Cylinder Installation
G10110
G10111
11. Install HYD09922 Hydraulic Hose (49) between
the middle fitting on the hydraulic shelf and the
port of the Lift Cylinder (41). Tighten both ends
securely.
7. Position the rod end of HYD07013 Lift Cylinder
(41) between the cylinder mounts of Push Frame
Assembly (2). Insert MSC05563 Clevis Pin (105)
through the cylinder mounts and secure with
HDW05544 Hairpin Cotter (104).
12. Install HYD01810 Hydraulic Hose (52) between
the left fitting on the hydraulic shelf and the
port of the Left Angle Cylinder (40). Apply
thread compound at the hose to cylinder
connection. Tighten both ends of the hose
securely.
8. Align the pivot holes of Coupler Assembly (1) with
the pivot holes of Push Frame Assembly (2).
9. Insert Pivot Pins (100A) through Coupler
Assembly (1) and Push Frame Assembly (2).
Place a 1" Flat Washer (100B) on Pivot Pin (100A)
then insert Cotter Pin (100C) through Pivot Pin
(100A). Spread the ends of Cotter Pin (100C).
13. Repeat step 12 for the Right Angle Cylinder
Hose.
10. Rotate Lift Cylinder (41) up to the cylinder mounts
located on Coupler Tower Assembly (1). Insert
Clevis Pin (105) through the cylinder mounts and
secure with Hair Pin Cotter (104).
5
Snowplow Assembly Procedure
Note: Please continue with the instructions below
if your plow is factory equipped with the
SmartHitch2™ option. If you are installing the
SmartHitch2™ option please see the
“SmartHitch2™ Installation Procedure” located in
this manual.
Figure 9. Light Bar Assembly. (Standard)
G10132
19. Attach Light Bar (13) to the top of Coupler
Assembly (1) using two Hex Head Cap Screws
(91) and Hex Head Self Locking Nuts (109).
Note: The Light Bar should be positioned as close to
the Coupler Tower as possible. Only two holes will be
aligned for normal installations. Only two bolts per side
are needed to secure the Light Bar.
Figure 8. Connecting Hose
G10120
16. Remove the plug from the top end of Lift Cylinder
(41).
17. Attach one end of Hydraulic Hose (50) to Lift
Cylinder (41). Thread compound should be used
at this connection. Tighten connection securely.
18. Route Hydraulic Hose (50) in “S” shape and
connect the loose end to the rear Hydraulic Fitting
(54). Tighten connection securely.
Figure 10. Light Bar Assembly Adjustment.
G10131
Note: Figure 10 illustrates that the Coupler Assembly
and Light Bar have two sets of 1 inch adjustment holes
for mounting on different vehicles. These adjustment
holes may be needed in order to move the Light Bar
away from the vehicle’s hood.
6
Snowplow Assembly Procedure
25. Insert the unconnected ends of the Plow Wiring
Harness into the back of the Coupler through the
rubber grommet.
26. Connect the Plow Side Wiring Harness to the
Hydraulic Valve manifold as shown in Figure 32.
HYD07065 Super Duty Manifold Wiring
Diagram on Page 19 of this manual.
Note: The Green wire has a piggyback spade
connector to allow the Blue wire to connect to the
same terminal. The wires should be connected to
each other.
Figure 11. Headlight Mounting Assembly
Note: The Red/Black wire has a piggyback spade
connector to allow the Red wire to connect to the
same terminal. The wires should be connected to
each other.
G10115
20. Insert Light Bar Seal (79) into the Light Bar (13)
and seat it using the end of the Turn Signal (76C).
Note: All wires need to be connected if
TM
SmartHitch2 is standard on the plow.
21. Attach Turn Signal (76C) into the end of Light Bar
(13) using one Machine Screw (76F) and Nut
(76G).
Note: If SmartHitch2 is not being installed, the
White/Black wire will not be used. The White/Black
wire should be capped and secured to the inside of
the coupler tower. The White/Black wire will be
energized with 12V+ when the pump is running.
TM
Note: Do not over tighten Machine Screw (76F).
22. Bolt Driver Side Headlight (76A) on to Light Bar
(13) using two bushings (76H), ½” Nuts (76D)
and ½” Star Washers (76E) as shown in Figure
11.
23. Repeat Steps 20 through 22 for Passenger
Side Headlight (76B) and Passenger Side Turn
Signal (76C).
Figure 13. Assembly of Blade Guides.
G10071
28. Attach Blade Guides (16) to Blade Assembly (4)
using Hex Head Cap Screws (94) and Self
Locking Nuts (115).
Figure 12. Securing Wiring Harness
G10126
24. Secure Wiring Harness (61) to Light Bar (13)
using wire ties as shown above.
7
SmartHitch2TM Installation Procedure
SmartHitch2TM Installation
Procedure
Note: This installation procedure is used for installing
TM
the SmartHitch2 option. This procedure may be
TM
ignored if the SmartHitch2 option has been
previously installed.
1. Remove Hydraulic Cover (14) to expose Hydraulic
Valve Manifold (30).
M
Figure 15. Installing SmartHitch2 Hose
G10120
7. Remove the plug from the top of Hydraulic Valve
Manifold (30).
8. Install 90-Degree O-Ring Swivel Fitting (54) into
the Hydraulic Valve Manifold (30). The fitting
should be positioned so the open end of the fitting
is facing forward.
9. Remove the breather vent from the top of the
Hydraulic Lift Cylinder.
TM
Figure 14. SmartHitch2
Valve Installation
G10130
10. Connect one end of ¼ x 15 ½” Hose (50) to the
Lift Cylinder (41).
2. Remove the plug from the face of Hydraulic Valve
Manifold (30).
TM
3. Install HYD07047 SmartHitch2
Valve (30C).
11. Connect the opposite end of Hose (50) to the 90Degree Swivel Fitting (54) located in the Manifold.
Attachment
TM
12. Insert the SmartHitch2 Toggle Switch through
the side hole of the Coupler.
4. Place HYD01638 Valve Coil (30G) on the stem of
the Valve.
13. Tighten the switch with the jam nut provided.
5. Place brown Ground Strap over the top of valve
stem.
14. Secure with the Switch Boot onto the end of the
switch.
Note: DO NOT OVER-TIGHTEN coil nut. The valve
will be damaged if the coil nut is over-tightened.
6. Install HYD07060 Coil Nut (30K) onto the valve.
Tighten 1/8 turn past finger tight.
8
SmartHitch2TM Installation Procedure
TM
Figure 16. SmartHitch2
Wiring Diagram
G10447
TM
15. Connect MSC04672 Orange SmartHitch2
Wiring Harness to the switch and manifold as
shown above.
16. Connect MSC09867 White and MSC09866 Black
TM
SmartHitch2 Wiring Harnesses to the switch
and manifold as shown above.
17. Connect the White and Black Wire from the main
wiring harness to the switch as shown above.
9
Electrical System Wiring Procedure
Note: If your connectors do not match the connectors
on the wiring harness or you have a four-headlight
system a Headlight Adapter Kit will be needed. If you
are installing a Headlight Adapter Kit, see “Headlight
Adapter Installation Procedure” located in this manual.
Electrical System Wiring
Procedure
WARNING!
Before starting any Electrical Wiring Procedure
make sure that the engine is not running and that
the engine has had sufficient time to cool down.
Failure to do so may result in serious bodily injury
or death.
WARNING!
Before starting any Electrical Wiring Procedure
make sure to disconnect the battery. Failure to
do so may result in serious bodily injury or death.
Figure 18. Passenger Side Headlight
G10141
4. Disconnect the passenger side OEM Wiring
Harness (F) from the back of the passenger side
vehicle headlight.
5. Connect the Blue Sealed Beam Connector (D)
from Wiring Harness (60) into the back of the
passenger side vehicle headlight.
Figure 17. Driver Side Headlight
6. Connect the Black Rubber Connector (E) from
Wiring Harness (60) into the OEM Wiring Harness
(F). OEM Wiring Harness (F) is the vehicle
connector that was unplugged from the back of
the headlight in Step 4.
G10140
Note: Dielectric grease should be applied to all
electrical connections.
1. Disconnect the driver side headlight connector
plug (C) from the back of the driver side vehicle
headlight.
2. Connect the Blue Sealed Beam Connector (A)
from Wiring Harness (60) into the back of the
driver side vehicle headlight.
3. Connect the Black Rubber Connector (B) from
Wiring Harness (60) into the OEM Wiring Harness
(C). OEM Wiring Harness (C) is the vehicle
connector that was unplugged from the back of
the headlight in Step 1.
10
Electrical System Wiring Procedure
NOTICE
Before splicing into any electrical circuit, identify
the circuit with a test lamp. Failure to test circuits
may result in vehicle damage.
Figure 19. Connecting Park and Turn
G10143
Note: Some trucks require a turn signal relay kit.
Figure 20. Internal Cab Wires
G10144
7. Connect the PINK wire from Wiring Harness (60)
to the passenger side turn signal wire. Use the
splice connector provided to you in the hardware
kit.
11. Pull the two BLACK wires (H), BLACK/RED wire
(I), and the 9 Pin Molex connector (G) from the
engine compartment into the cab through the 11/4” diameter hole in the firewall.
8. Connect the VIOLET wire from Wiring Harness
(60) to the driver side turn signal wire. Use the
splice connector provided to you in the hardware
kit.
12. Install MSC03761 Split Rubber Grommet (Not
Shown) into the hole that was cut in the firewall.
13. Connect the Two Tab Connectors (H) to
MSC04747 Headlight Toggle Switch (77A) as
illustrated in the figure above.
9. Connect the YELLOW wire from Wiring Harness
(60) to the driver side park light wire. Use the
splice connector provided to you in the hardware
kit.
NOTICE
Position the switch where it will not interfere
with driver’s ability to see and where it will not
affect the driver’s ability to operate the motor
vehicle.
Note: Be sure that the firewall is clear of obstructions
before drilling in Step 10.
10. Drill a 1-1/4" diameter hole through the firewall.
The hole should be located on the driver side, in
an easily accessible area.
14. Choose an area of the vehicle’s dashboard for the
light Toggle Switch to be mounted. Clean the area
thoroughly. Allow the area to dry completely.
15. Remove the adhesive backing and apply the
switch to the clean area of the dashboard. Apply
pressure for 30 seconds.
11
Electrical System Wiring Procedure
NOTICE
Be sure the wire loom does not interfere with the
operation of the vehicle’s pedals.
Note: Location of the wires on the small terminals
does not matter but the wires should not be on the
same terminal.
16. Secure the 9 Pin Molex Connector (G) and wire
loom underneath the dashboard.
22. Attach Power Unit Solenoid (64) securely inside
the engine compartment. The Power Unit
Solenoid should be mounted in the upright
position as illustrated in Figure 21.
17. Plug the controller into the 9 Pin Molex Connector
(G).
Note: The solenoid must be installed so that the
solenoid posts do not contact the body, hood, or any
other conductive material on the vehicle.
18. Mount the plow control in a location that is
comfortable for the operator to reach, and where
the operator will not contact the control in the
event of a crash. (See “Straight Blade Controller
Mounting Instructions” located in this manual.)
23. Attach the eyelet end (L) of RED Power/Ground
Cable (62) to the top of Pump Solenoid (64).
24. Connect the eyelet end (M) of Battery Cable (66)
to the top post of Pump Solenoid (64).
19. Connect the BLACK/RED wire (I) to a “keyed”
12V+ ignition source.
Note: Location of the wires on the small terminals
does not matter but the wires should not be on the
same terminal.
Note: This 12V+ source should only be active when
the key is in the ON position. Failure to wire to a
“keyed” source can allow a condition to occur causing
the battery to drain.
Figure 22. Battery Connections
Figure 21. Solenoid Connections.
G10146
25. Attach the eyelet end (N) of BLACK
Power/Ground Cable (62) to the negative battery
terminal.
G10145
20. Connect the WHITE/BLACK wire (J) of Wiring
Harness (60) to the small terminal on Pump
Solenoid (64).
26. Connect the BROWN wire (Q) to the negative
battery terminal.
27. Connect the unattached end (P) of Battery Cable
(66) to the positive battery terminal.
21. Connect the BROWN wire (K) of Wiring Harness
(60) to the small terminal on Pump Solenoid (64).
28. Connect the RED Fused wire (O) to the positive
battery terminal.
12
Electrical System Wiring Procedure
Figure 23. Vehicle Connections
G10148
29. Mount the Black 15 Pin Control Harness
Connector to the lower area of the bumper using
MSC03813 Control Harness Mounting Bracket
30. Mount the BLACK and RED 2 Pin Power Ground
Connector to the lower area of the bumper using
MSC03491 Power Ground Mounting Bracket.
Note: Installation location will vary depending on
truck.
Figure 24. Relay Mounting.
G10152
31. Attach the Relay Pack securely to the inside of the
engine compartment using four HDW01766 Sheet
Metal Screws. The relays should be positioned
upright as illustrated above.
13
Electrical System Wiring Procedure
35. Test for the proper operation of the Headlight Wiring
Harness. Follow the procedures below.
Note: To test plow lights, the IGNITION must be in the
ON position.
Figure 25. Vehicle Option Connector
G10202
32. Locate vehicle option connector. Align the
connector so that the arrow on the Vehicle Option
Connector is positioned to match the vehicle it is
installed on. This is illustrated in Figure 24.
 LOW BEAM (Truck Lights)
 Vehicle Headlight Switch – ON
 Low Beam Lights on Truck Indicator
 Plow Headlight Toggle Switch –TRUCK
RESULTS - ONLY vehicle low beam headlights should be illuminated.
 HIGH BEAM (Truck Lights)
 Vehicle Headlight Switch – ON
 High Beam Indicator Light – ON
 Plow Headlight Toggle Switch –TRUCK
Note: If your vehicle is not listed in the above figure
use the Standard Orientation. If the Vehicle Option
Connector is not properly connected the lights on the
plow will not function correctly.
RESULTS - ONLY vehicle high beam headlights should be illuminated.
33. Secure all plow harness wiring.
 LOW BEAM (Plow Lights)
 Ignition - ON
 Vehicle Headlight Switch – ON
 Low Beam Lights on Truck Indicator
 Plow Headlight Toggle Switch - PLOW
NOTICE
All plow wiring should be secured within the
engine compartment in a position that provides
sufficient room so that hot or moving parts will
not be contacted. Vehicle damage could occur if
wires are not properly secured.
RESULTS - ONLY plow low beam headlights should be illuminated.
 HIGH BEAM (Plow Lights)
 Ignition - ON
 Vehicle Headlight Switch – ON
 High Beam Indicator Light – ON
 Plow Headlight Toggle Switch – PLOW
34. Attach the snowplow to the vehicle. Use the
“Snowplow Mounting Procedure” that is located in
this manual to properly attach the snowplow to the
vehicle.
RESULTS - ONLY plow high beam headlights should be illuminated.
 TURN SIGNALS (Plow and Truck)
 Left Turn Signal Indicator – ON
RESULTS - BOTH Left Plow and Left Truck turn signal bulbs should
be flashing.

Right Turn Signal Indicator – ON
RESULTS - BOTH Right Plow and Right Truck turn signal bulbs
should be flashing.
 Park Lights (Plow and Truck)
 Park Lights on Vehicle – ON
RESULTS - ALL FOUR, Left Plow, Right Plow, Left Truck, and Right
Truck Park Lights should be on.
Note: If any of the lights are not working
properly, re-check the wiring against the
“Electrical Wiring Diagram” located in this
manual and make any necessary corrections.
14
Headlight Adapter Installation Procedure
Headlight Adapter Installation
Procedure
Figure 27. Dual Headlight Adapter Connections
G10151
Note: This is a general diagram for most 4-headlight
vehicles. All vehicles and headlight adapters may not
be identical. Installation will be very similar.
Figure 26. Single Headlight Adapter Connections
G10149
1. Disconnect OEM Headlight Connector Plugs (A
and D) from the back of the vehicle headlight.
Note: This is a general diagram for most 2-headlight
vehicles. All vehicles and headlight adapters may not
be identical. Installation will be very similar.
2. Connect two ends of Headlight Adapter (73A) into
the back of the vehicle headlights.
1. Disconnect the OEM Headlight Connector Plug
(A) from the back of the vehicle headlight.
3. Connect the Black Rubber Female Socket (B) of
Headlight Adapter (73A) into the plow wiring
harness.
2. Connect one end of Headlight Adapter (73A) into
the back of the vehicle headlight.
4. Connect the Blue Sealed Beam Connector (C) of
Headlight Adapter (73B) into the plow wiring
harness.
3. Connect the Black Rubber Female Socket (B) of
Headlight Adapter (73A) into the plow wiring
harness.
5. Connect the opposite end of Headlight Adapter
(73B) into the OEM Wiring Harness (A).
4. Connect the Blue Sealed Beam Connector (C) of
Headlight Adapter (73B) into the plow wiring
harness.
6. Grease, tuck, and secure OEM Connector Plug
(D). This connector is not used.
5. Connect the opposite end of Headlight Adapter
(73B) into the OEM Headlight Connector Plug (A).
7. Repeat Steps 1 through 6 for the opposite side
headlight.
6. Repeat Steps 1 through 5 for the opposite side
headlight.
8. Continue with the Step 7 of “Electrical System
Wiring Procedure” located in this manual.
Note: In some older vehicles it is not necessary to
pull power from both sides of the headlights. In this
case only three adapters will be needed. Follow the
Headlight Adapter Installation Instructions that are
packaged with the Headlight Adapter Kit.
7. Continue with the Step 7 of “Electrical System
Wiring Procedure” located in this manual.
15
Electrical System Wiring Diagram
Figure 28. Electrical System Wiring Diagram
16
G10134
Electrical System Wiring Schematic (Plow Side)
Figure 29. Electrical System Wiring Schematic (Plow Side)
G10271
17
Electrical System Wiring Schematic (Truck Side)
Figure 30. Electrical System Wiring Schematic (Truck Side)
G10272
18
RT3 Straight Blade Manifold Wiring Diagrams
Figure 31. HYD07090 Standard Duty Manifold Wiring Diagram
G10446
Figure 32. HYD07091 Super Duty Manifold Wiring Diagram
G10447
Wire Color
Wire Function
Green
Red
White
Orange
Red/Black
Blue
Black
White/Black
Brown
Blade Left
Blade Right
Lift
Lower
Blade Right
Blade Left
TM
SmartHitch2 (12V)
Pump Solenoid
Ground
19
Hydraulic Power Unit Fill Procedure
Hydraulic Power Unit Fill
Procedure
FULL
Figure 34. Oil Full Level
G10411
Plow Position to Check Oil: The plow should be
attached to the truck, sitting flat on the ground, with
the blade in the straight position.
6. With the blade in the straight position and the
plow lowered to the ground, check the fluid level.
Fluid should be visible in the external fill port. If
fluid is not visible, fill until visible. Your reservoir
should now be properly filled.
Figure 33. External Fill – Backside View
Note: Hydraulic fluid should be replaced annually
with BOSS Snowplow High Performance Hydraulic
Fluid.
G10124
Note: If your plow is equipped with SmartHitch2™
you must hydraulically power the light tower down. Do
not manually pull the light tower down. Failure to
hydraulically power the light tower down will create an
air pocket in the hydraulic system. Oil will spill out of
your internal filler cap.
Step 1 of the following fill procedure is intended for a
new plow with an empty hydraulic system.
Initial Plow Position: Start with the plow unattached
from the vehicle and the lift cylinder completely
collapsed. The light tower will be tilted forward.
1. Remove HYD04810 Fill Cap (20F) from
HYD04809 Street Elbow (20G) and fill with BOSS
High Performance Hydraulic Fluid. Continue to fill
Street Elbow (20G) until no more fluid will be
accepted. (Approx. 2 quarts.)
WARNING!
When adjusting Flow Control Valve (30D) make sure
all appendages are clear of the plow blade and
observers are standing a safe distance away from the
plow blade. The plow may drop if your controller is in
the FLOAT position. Make sure your controller is in
the OFF position before attempting to adjust the plow.
Failure to follow this warning could result in bodily
harm.
2. Attach the plow to the vehicle.
Note: If your plow is equipped with SmartHitch2™
you must hydraulically power the light tower up. Do
not manually push the tower up. Failure to
hydraulically power the light tower up will create an air
pocket in the hydraulic system. Oil will spill out of your
internal filler cap.
Note: Flow Control Valve (31C) is not available on
Green colored Hydraulic Manifolds used on Standard
Duty and Sport Duty snowplows.
7. Adjust Flow Control Valve (30D) to obtain the
speed desired for lowering the plow by loosening
the jam nut, then adjusting the set screw.
Counter-clockwise adjustment will increase the
speed the plow descends. Retighten the jam nut
when the desired speed is obtained.
3. Raise the plow.
4. With the plow in the raised position, cycle through
both angle functions several times.
5. Lower the plow to the ground.
Note: If your plow will not lower, Flow Control Valve
(30D) is completely closed. Refer to Step 7 to adjust
Flow Control Valve (30D).
20
RT3 Headlight Aiming Procedure
Headlight Aiming
Procedure
NOTICE
The installer of these snowplow lights must
certify that installation conforms to applicable
Federal Motor Vehicle Safety Standards.
4. Mark (or tape) the vehicle centerline of the
headlights and the vehicle itself on the screen.
Mark the horizontal centerline of the headlights on
the screen (distance from ground to headlight
centers).
Screen Located
25' From Headlights
Align With Vehicle
Centerline Vertical Centerline Ahead
of Right Headlight
1. Place the vehicle on a level surface 25 feet in
front of a matte-white screen, such as a garage
door. The screen should be perpendicular to both
the ground and the vehicle.
For Type 2 (Sealed Beam)
Headlights on Low Beam
2. The vehicle should be equipped for normal
operation. The snowplow blade should be in place
and in the raised position.
3. Below are some points listed by the Society of
Automotive engineers (SAE) pertinent to headlight
aiming. These points can be found in publication
#SAEJ5991D.
Preparation for Headlight Aim or Inspection
Before checking beam aim, the inspector shall:
Distance Between
Headlight Centers
 Remove ice or mud from under fenders.
 See that no tire is noticeably deflated.
 Check vehicle springs for sag or broken
leaves.
 See that there is no load in the vehicle other
than the driver.
 Check functioning of any “level-ride” controls.
 Clean lenses and aiming pads.
 Check for bulb burnout, broken mechanical
aiming pads, and proper beam switching.
 Stabilize suspension by rocking vehicle
sideways.
Figure 35. Headlight Aiming Procedure
G10153
5. The correct visual aim for Type 2 headlights is
with the top edge of the high intensity zone of the
lower beam below the horizontal centerline and
the left edge of the high intensity zone on the
vertical centerline. See diagram above.
21
Hydraulic Valve Assembly Parts List
Figure 36. Straight Blade Manifold with SmartHitch2™ Parts Diagram
Ref.
Description
30 Hydraulic Valve Assembly with SmartHitch2TM (Red)
Hydraulic Valve Assembly (SmartHitch2TM Ready) (Green)
30A Hydraulic Valve, Lift/Lower Cartridge
30B Hydraulic Valve, Angle Cartridge (3 Position - 4 Way Spool)
30C Hydraulic Valve, SmartHitch2TM Attach (HYD07091 only)
30D Hydraulic Valve, Flow Control Cartridge (HYD07091 only)
30E Relief Valve, Hydraulic Crossover (3,800 PSI)
30F Check Valve
30G Coil, Hydraulic Valve
30H Nut, Coil - used with valve HYD01637 & HYD07100
30K Nut, Coil - used with valve HYD07047
30L Orifice Plug, 0.12” ID (HYD07090 only)
22
G10072
Part Number
HYD07091
HYD07090
HYD01637
HYD07100
HYD07047
HYD07048
HYD07027
HYD01640
HYD01638
HYD07059
HYD07060
HYD07120
Qty
1
2
1
1
1
1
1
5
2
1
1
Straight Blade Controllers
Joystick Control Operating
Instructions
Figure 37. Straight Blade Control Operation
G10154
1. Toggle the ON/OFF switch to the ON position. A
red indicator light will illuminate on the switch.
The joystick is now active.
2. To RAISE the blade of the plow, pull the control
stick towards you.
3. To LOWER the blade of the plow, push the
control stick away from you.
4. To FLOAT the blade along the contour of the
plowing surface, push the controller away from
you until the stick reaches the detent position.
(You will feel the stick click into the detent
position.) The joystick will stay in the FLOAT
position until it is physically re-centered on the
control box.
5. To ANGLE the blade RIGHT, push the controller
stick to the right.
6. To ANGLE the blade LEFT, push the controller
stick to the left.
7. The control should be turned off when not in
use. It can then be unplugged and stored.
23
Straight Blade Controllers
JOYSTICK CONTROL
UNIVERSAL MOUNTING KIT MSC04026
Figure 38. Joystick Control Universal Mounting Kit Components
Reference
40A
40B
40C
40D
A
B
C
Description
Joystick, Intermediate Mounting Bracket
Joystick, Mounting Bracket
Joystick, Spring Clip
Pad, Foam
Screw, #8-32 X 1/4 Machine Black
Washer, #10 Flat Washer Black
Nut, #8-32 X 3/16 Alum Binding Post
24
G10109
Part Number
MSC04028
MSC04029
MSC04027
MSC04038
HDW05591
HDW05592
HDW05593
Straight Blade Controllers
Control
Operating Instructions
Figure 39. Straight Blade Control Instructions
G10366
ON/OFF: Push the ON/OFF switch to the left ON
position to turn the control on. Green LED indicators
will light up on the control. Push the ON/OFF switch to
the right OFF position to turn the control off.
ANGLE RIGHT: To angle the blade to the right, press
and hold the angle right button until the blade is fully
angled.
Note: The control should be turned off when not in
use. It can then be unplugged and stored.
RAISE: To raise the blade of the plow, quickly press
the center button upward twice. You can also press
and hold the center button upward until the blade is
fully raised.
SLEEP mode: If the controller is ON but not used for
20 minutes, the automatic SLEEP mode will be
activated. The controller LED lights will flash green
and red when the controller is in SLEEP mode.
LOWER: To lower the blade of the plow, quickly push
the center button downward twice. You can also press
and hold the center button downward until the blade is
fully lowered.
FLOAT: The plow will automatically activate the
FLOAT feature when the center button is quickly
pressed downward twice. (The center LED indicator
will turn RED). You can also press and hold the center
button downward for 2 seconds to activate the FLOAT
feature. (The center LED indicator will turn RED).
“What is FLOAT?”: The FLOAT feature allows the
plow blade to mirror the contour of the ground. Press
the raise button to turn the FLOAT function off.
ANGLE LEFT: To angle the blade to the left, press
and hold the angle left button until the blade is fully
angled.
25
Straight Blade Controllers
Note: Other mounting options are available. Contact your
BOSS Snowplow dealer for more information.
Control
Mounting Instructions
Figure 40. SmartTouch2
TM
Mounting Hardware
G10311
1. Remove the Swivel Mount and Tab from the
MSC05058 Swivel Mount Kit.
2. Use the enclosed alcohol wipe to clean a spot on the
vehicle interior where you want to place the
TM
SmartTouch2 Control. Wipe dry immediately with a
cloth or paper towel.
3. Do not apply when the surface temperatures are
lower than +60˚F (Working temperature range of the
adhesive is -40˚F to +200˚F).
4. Peel off the paper backing on one side of the
adhesive and apply to Swivel Mount. Apply maximum
pressure to all areas.
5. Apply the Swivel Mount onto the spot of the interior
that was just cleaned. MAKE SURE IT IS IN THE
CORRECT PLACE. Once it is placed it cannot be
removed without destroying the adhesive.
TM
6. Clean the back of the SmartTouch2
alcohol wipe.
Control with the
7. Peel off adhesive backing of tape, apply to Tab, and
press firmly.
8. Remove remaining backing and apply the Tab to the
TM
back of the SmartTouch2 Control. Apply pressure
for 30 seconds.
NOTICE
After attaching the Swivel Mount, let it sit unused for
72 hours before attaching the SmartTouch2TM
Control to allow the adhesive to bond to the surface
and ensure secure mounting.
TM
9. Place SmartTouch2
Control on the Swivel Mount.
26
Troubleshooting Guide
Troubleshooting Guide
Glossary of Problems:
1. Pump motor does not run.
2. Pump continues to run with switch in neutral.
3. Plow will not lower.
4. Plow will not raise or raises slowly, motor runs.
5. Blade angles while plowing snow.
6. Plow lowers too fast.
7. Blade will not angle, but motor runs.
8. Blade angles too easily while plowing.
9. Oil leaks from cylinders.
10. Battery goes dead with all switches in neutral.
11. Plow lights are dim, will not come on or flicker.
12. Turn signals flash at a rapid rate.
13. High beam indicator light not functioning properly.
14. Plow does not clean-up snow from low areas.
15. Oil runs out of fill cap of hydraulic pump.
16. Pump chatters when raising the plow or angling blade.
17. SmartHitch2TM will not attach plow.
18. Plow lights and truck lights are on at the same time.
19. Plow and truck High and Low beam lights are on at the same time.
20. Plow High beam and Low beam are on at the same time.
PROBLEM
1. Pump motor does not
run.
DIAGNOSTIC CHECK
Check power/ground
cables and control cables
are connected properly.
Check for voltage at pump
motor while ignition switch
is on and LIFT control
button is pushed.
Check for power to the
solenoid by testing for
voltage between both
large terminals and
ground.
Check for voltage between
the other large terminal of
the solenoid and ground
while jumping power to the
small terminals with the
white wire.
27
RESULT
Connect.
If voltage is present, pump
motor has failed or pump
has seized. Motor brushes
may be replaced, otherwise
replace pump/motor
assembly.
If voltage is not present
between one large terminal
and ground, the cable
between the battery and
solenoid is disconnected or
broken.
If NO voltage is present,
solenoid has failed and
must be replaced. If voltage
is present, wire from small
terminal of solenoid to
ground may be
disconnected or broken.
Troubleshooting Guide
PROBLEM
DIAGNOSTIC CHECK
Test power to the control
box by checking voltage
between black wire and
ground at the white 9-pin
connector.
2. Pump continues to run
with switch in neutral.
Disconnect controller,
ignition ON.
3. Plow will not lower.
Check power/ground
cables and control cables
are connected properly.
Check flow control valve.
Check wiring on valve
manifold for proper
connections.
Check for voltage between
solenoid valve terminal
and ground with ignition
switch on and control
switch in FLOAT position.
Test power to the control
box by checking voltage
between black wire and
ground at the white 9-pin
connector.
4. Plow will not raise or
raises slowly (pump motor
runs).
Check hydraulic fluid level.
28
RESULT
If NO voltage is present,
power from fuse box has
become disconnected. If
voltage is present check
wiring and control box
switch.
If pump continues to run,
solenoid has failed in the
closed position. Quickly
remove power to the pump
by disconnecting the
power/ground cables to the
plow. Replace solenoid.
If pump stops running,
check wiring of switch box
for short between black and
white/black wire in control
box, or failed switch.
Connect.
If flow control valve is
completely closed, place
RAISE/LOWER switch on
controller in NEUTRAL,
then open the flow control
valve.
Refer to the Manifold Wiring
Diagram in this manual.
If voltage is present
solenoid valve or valve coil
has failed. Replace valve.
If NO voltage is present,
power from fuse box has
become disconnected. If
voltage is present, check
wiring and switch of control
box.
Hydraulic fluid level should
be within ¾” from top of
reservoir when lowered.
See Hydraulic Fluid Fill
Procedure located in this
manual.
Troubleshooting Guide
PROBLEM
DIAGNOSTIC CHECK
Check that power/ground
cables and control cable
are connected properly.
Check wiring on valve
manifold for proper
connections.
Load test battery.
Check pressure at
pressure port of pump.
Check LIFT solenoid valve
5. Blade angles while
plowing snow.
Check angle solenoid
valve on manifold
Check pressure
6. Plow lowers too fast.
Check flow control valve.
7. Blade will not angle or
angles slowly, motor runs.
Check hydraulic fluid level.
Check power/ground
cables and control cable
are connected properly.
Check wiring on valve
manifold for proper
connections.
Load test battery.
Check angle solenoid
valve.
29
RESULT
Connect.
Refer to the Manifold Wiring
Diagram in this manual.
Replace battery if weak or
defective.
If pressure is less than
2500 psi (at end of lift)
motor brushes may be
defective, pump pressure
relief valve may be
contaminated, damaged, or
set less than 2500 psi,
pump may be worn.
Lift solenoid valve not
opening completely.
Replace.
Check wiring and controller.
If solenoid valve is
contaminated, clean or
replace.
If pressure relief valve is
contaminated, clean or
replace.
Close flow control valve to
desired drop speed.
Hydraulic fluid level should
be within ¾” from top of
reservoir when lowered.
See Hydraulic Fluid Fill
Procedure located in this
manual.
Connect.
Refer to the Manifold Wiring
Diagram in this manual.
Replace battery if weak or
defective.
Angle solenoid valve not
opening completely.
Replace.
Check wiring and controller.
Troubleshooting Guide
PROBLEM
8. Blade angles too easily
while plowing.
DIAGNOSTIC CHECK
Pressure relief valve
pressure set too low.
9. Oil leaks from cylinders.
Loose packing.
Check rod condition.
10. Battery goes dead with
all switches in neutral.
11. Plow lights are dim, will
not come on or flicker.
Possible short in switches.
Possible short in wiring
harness.
Possible short in valve
coils.
Check electrical
connections.
Check headlight adapter
wires.
12. Turn signals flash at a
rapid rate.
13. High beam indicator
does not function properly.
14. Plow does not clean-up
snow from low areas.
15. Oil running out of fill cap
of hydraulic pump.
16. Pump chatters when
raising plow or angling
blade.
17. SmartHitch2TM will not
attach plow.
Check relay. Relay should
click when activated.
Check flasher.
Check headlight adapters.
Check electrical
connections to plow
lights/truck lights toggle
switch.
UP/DOWN switch not in
FLOAT.
Watch customer mount
and dismount plow for
proper procedure.
Pump reservoir over filled.
Hitting snow banks too
hard.
Hydraulic fluid low.
Make sure key is on and
controller is in FLOAT.
30
RESULT
See an Authorized BOSS
Dealer for pressure relief
valve adjustment.
Tighten packing 1/8-turn
increments until leak stops.
If rods are pitted or rough,
polish with copus cloth or
extra fine steel wool.
Inspect wiring of controller.
Repair damaged wire.
Replace coils.
Clean and repair any
corroded or damaged
terminals.
Verify proper headlight
adapters are being used
and are correctly installed.
Replace relay.
Replace original vehicle
flasher with heavy-duty sixlamp flasher provided.
Verify proper headlight
adapters are being used
and are correctly installed.
Refer to the Electrical
Wiring Diagram in this
manual.
Place switch in FLOAT
position.
Power SmartHitch2TM
functions if installed. See
Mounting instructions.
Reservoir should be filled to
¾” from top.
Do not plow recklessly.
Add hydraulic fluid.
Reservoir should be filled to
¾” from top.
Turn key on and put
controller in FLOAT.
Troubleshooting Guide
PROBLEM
18. Plow lights and truck
lights are on at the same
time.
DIAGNOSTIC CHECK
Make sure controller is
staying in the FLOAT
position.
Check valve block and
SmartHitch2TM switch for
proper connections.
Check vehicle harness
wiring to truck headlights.
19. Plow and truck High
beam and Low beam are on
at the same time.
Check headlight adapters
for correct connections.
20. Plow High beam and
Low beam are on at the
same time.
Check vehicle option
connector.
31
RESULT
If controller comes out of
FLOAT when using the
SmartHitch2TM switch,
replace the controller.
Refer to manifold wiring
diagram located within this
manual.
Refer to electrical system
wiring instructions located
within this manual. Ensure
OEM is not plugged into
truck headlight.
Light adapters for GM
trucks can be plugged in
two ways. Make sure all
four adapters are in the
proper orientation for your
vehicle.
Refer to electrical system
wiring instructions located
within this manual. Vehicle
option connector may need
to be reversed.
Recommended Pushbeam Height
Figure 41. Recommended Pushbeam Height
G10436
Recommended Bolt Torque
Figure 42. Recommended Bolt Torque
G10410
NOTE: The torque values listed above are based on dry, coated bolts, variables such as oil, or other lubrications
may appreciably alter these values and must be taken into consideration.
NOTICE: IT IS IMPORTANT THAT ALL FASTENERS BE PROPERLY TORQUED TO ASSURE A SAFE
OPERATING PLOW.
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement