# SS0131 - Antenna Theory 2005

```SUBCOURSE
EDITION
SS0131
A
US ARMY SIGNAL CENTER AND FORT GORDON
ANTENNA THEORY
(SC: 25C)
EDITION DATE: FEBRUARY 2005
ANTENNA THEORY
Subcourse Number SS0131
EDITION A
United States Army Signal Center and Fort Gordon
Fort Gordon, Georgia 30905-5000
5 Credit Hours
Edition Date: February 2005
SUBCOURSE OVERVIEW
This subcourse is designed to teach the theory, characteristic, and capabilities of the various types of
tactical combat net radio, high frequency, ultra high frequency, very high frequency, and field expedient
antennas.
The prerequisites for this subcourse is that you are a graduate of the Signal Office Basic Course or its
equivalent.
This subcourse reflects the doctrine which was current at the time it was prepared. In your own work
situation, always refer to the latest official publications.
Unless otherwise stated, the masculine gender of singular pronouns is used to refer to both men and
women.
TERMINAL LEARNING OBJECTIVE
ACTION:
Explain the basic antenna theory and operations of combat net radio, high
frequency, ultra high frequency, very high frequency, and field expedient
antennas.
CONDITION:
Given this subcourse.
STANDARD:
To demonstrate competency of this subcourse, you must achieve a minimum of
70 percent on the subcourse examination.
i
SS0131
Section
Page
Subcourse Overview .................................................................................................................................... i
Lesson 1:
Antenna Principles and Characteristics ............................................................................. 1-1
Practice Exercise .............................................................................................................. 1-14
Answer Key and Feedback ............................................................................................... 1-16
Lesson 2:
Tactical Antennas ............................................................................................................... 2-1
Practice Exercise ............................................................................................................... 2-26
Answer Key and Feedback .............................................................................................. 2-28
Appendix ................................................................................................................................................ A-1
SS0131
ii
ANTENNA PRINCIPLES AND
CHARACTERISTICS
LESSON 1
ANTENNA PRINCIPLES AND CHARACTERISTICS
01-5879.07-9001
OVERVIEW
LESSON DESCRIPTION:
In this lesson, you will learn about the theory of antennas, to include the principles of antenna radiation,
the characteristics of antennas, and the formulas used in antenna design.
TERMINAL LEARNING OBJECTIVE
ACTION:
Explain basic antenna theory.
CONDITION
Given this lesson.
STANDARD:
To demonstrate competence, you must achieve a minimum of 70 percent on the
subcourse examination.
REFERENCES:
The material in this lesson was derived from FM 11-64 and FM 24-18.
INTRODUCTION
An antenna is an integral component of a radio communications system. Signal officers must
understand how radio antennas function. Planners and operators should know how signals radiate, what
can be done to enhance signal propagation and reception, and how to reduce unwanted interference.
1-1
SS0131
1. General. An antenna is the component of a radio system that is used to send or receive a radio
signal. A radio frequency (RF) signal that has been generated in a radio transmitter travels through a
transmission line (coaxial cable) to an antenna. An antenna connected to a transmitter is the device that
releases RF energy (in the form of an electromagnetic field) to be sent to a distant receiver. The
receiving antenna picks up the RF energy. As the electromagnetic field strikes the receiving antenna, a
voltage is induced into the antenna, which serves as a conductor. The induced RF voltages are then used
to recover the transmitted RF information.
2. Current and voltage distribution.
a. A current flowing in a wire of a length related to the RF produces an electromagnetic field. This
field radiates from the wire and is set free in space. The principles of radiation of electromagnetic
energy are based on two laws.
(1) A moving electric field creates a magnetic (H) field.
(2) A moving magnetic field creates an electric (E) field.
b. In space, these two fields will be in-phase and perpendicular to each other at any given moment.
Although a conductor is usually considered to be present when a moving electric or magnetic field is
mentioned, the laws governing these fields do not say anything about a conductor. Thus, these laws
hold true whether a conductor is present or not.
c. The current and voltage distribution on a half-wave Hertz antenna is shown in Figure 1-1. In
view A, a piece of wire is cut in half and attached to the terminals of a high frequency (HF), alternating
current (AC) generator. The frequency of the generator is set so each half of the wire is one-quarter
wavelength of the output. The symbol for wavelength is the Greek letter lambda (D). The result is the
common dipole antenna.
d. At a given moment, the generator's right side is positive and its left side is negative. A law of
physics states that like charges repel each other. Consequently, electrons will flow away from the
negative terminal as far as possible while the positive terminal will attract electrons. View B of Figure
1-1 shows the direction and distribution of electron flow. The distribution curve shows that most current
flows in the center and none flows at the ends. The current distribution over the antenna is always the
same, regardless of how much or how little current is flowing. However, current at any given point on
the antenna will vary directly with the amount of voltage that the generator develops.
e. One-quarter cycle after the electrons begin to flow, the generator develops it; minimum voltage
and the current decreases to zero. At that moment, the condition shown in view C of Figure 1-1 will
exist. Although no current is flowing, a minimum number of electrons are at the left end of the line and
a minimum number are at the right end. The charge distribution along the wire varies as the voltage of
the generator varies (view C).
SS0131
1-2
(1) A current flows in the antenna with
an amplitude that varies with the generator
voltage.
(2) A sine wave distribution of charge
exists on the antenna. The charges reverse
polarity every half cycle.
(3) The sine wave variation in charge
magnitude lags the sine wave variation in
current by one-quarter cycle.
3. Radiation of electromagnetic energy. As
mentioned earlier, a radio signal is generated by
a transmitter, and the RF power is delivered to
an antenna. Two fields are set up as the RF
power reaches the antenna. One is an induction
field associated with the stored energy; the other
is a radiation field. The intensities of these
fields are large at the antenna, and are
proportional to the amount of RF power
delivered to the antenna. A radio teletypewriter
(RATT) using a high-powered amplitude
modulation (AM) radio and a long-wire antenna
has stronger fields than a small ANT/PRC-77
frequency modulation (FM) manpacked radio.
Only the radiation field remains beyond a short
distance from the antenna. This radiation field
is made up of an electric component and a
magnetic
component
(electromagnetic
radiation). Figure 1-2 shows the components of
electromagnetic waves. The electromagnetic
field is responsible for the transmission and
reception of electromagnetic energy through
space.
A radio wave is a moving
electromagnetic field with components of
electric intensity and magnetic intensity
arranged at right angles to each other.
Figure 1-1. Current and voltage distribution
on an antenna
Figure 1-2. Components of electromagnetic
waves
1-3
SS0131
4. Antenna characteristics. Output from the transmitter is converted into electromagnetic energy by the
antenna and radiated into space. At the receiving antenna, the electromagnetic energy is collected and
converted into electrical energy and fed to the receiver.
a. Antenna reciprocity is the ability to use
the same antenna for transmitting and receiving.
In view A of Figure 1-3, the antenna radiates a
minimum amount of energy at right angles to
the axis of the antennas. Note the minimum
amount of radiation emanating along the axis of
the antenna. If the same antenna were used as a
receiving antenna (view B), it would receive
best in the same directions in which it produced
maximum radiation-at right angles to the axis of
the antenna.
b. Highly directional antennas transmit and
receive more in certain directions than others.
Gain is the ratio between the amount of energy
transmitted or received in these directions
compared to the energy that would be
transmitted or received if the antenna were not
directional. Antenna gain also gives directional
antennas greater transmission range than
omnidirectional antennas for an equal signal.
c. A radiated field is composed of electric
and magnetic lines of force which are called
Figure 1-3. Reciprocity of antennas
fields.
A radiated wave’s polarization is
determined by the direction of the electric field
in relation to the Earth.
If the lines of electric force are at right angles to the Earth's surface, the wave is vertically polarized
(Figure 1-4). If the lines of electric force are parallel to the Earth's surface, the wave is horizontally
polarized, as shown in Figure 1-5, page 1-6. When a single-wire antenna is used to extract (receive)
energy from a passing radio wave, maximum pickup results when the antenna is oriented so it lies in the
same direction as the electric field component. Thus, a vertical antenna is used for efficient reception of
vertically polarized waves, and a horizontal antenna is used for horizontally polarized waves. In some
cases, the field rotates as the waves travel through space. When this occurs, both the horizontal and
vertical components of the field exist, and the wave has elliptical polarization.
d. For ground-wave transmissions, medium and low frequencies are used, and the antennas need to
be vertically polarized. This allows the radio wave to travel a considerable distance along the ground
surface with minimum absorption by the Earth.
SS0131
1-4
Horizontal polarization cannot be used at
these frequencies because the electric lines
run parallel to and touch the Earth. As a
horizontal wave travels across the surface, it is
attenuated and is not propagated very far. At
high frequencies, either horizontal or vertical
polarization may be used with sky wave
transmission. This is because the sky wave
arrives at the receiving antenna elliptically
polarized. This polarization is a result of the
wave traveling obliquely through the Earth's
magnetic field and striking the ionosphere.
Thus, the transmitting and receiving antennas
can be either horizontal or vertical. When
using frequencies in the ultra high frequency
(UHF) or very high frequency (VHF) range,
either horizontal or vertical polarization is
acceptable. But, you must ensure that the
transmitting and receiving antennas have the
same polarization.
e. An advantage of vertical polarization
is that vertical half-wave and quarter-wave
antennas can provide omnidirectional
communications.
This helps when
communicating from a moving vehicle,
although it radiates equally to both enemy and
friendly forces. Another advantage, when
using vertical polarization, is that less
Figure 1-4 Vertically signal
inference is picked up from strong VHF and
UHF broadcast transmissions (television and FM
radio). This is because those systems use horizontal polarization.
1-5
SS0131
Figure 1-5. Horizontally polarized signal
f. Horizontally polarized antennas do have certain advantages and are preferred at high
frequencies. A horizontal antenna is less likely to pick up man-made interference (such as those
produced by automobile ignition systems and electrical appliances), which is usually vertically
polarized. A second advantage is that there is less absorption of radiated energy by buildings or wiring
when a horizontal antenna is used. In addition, a simple horizontal half-wave antenna is bi-directional
which is useful in minimizing interference from certain directions. Finally, horizontally polarized waves
suffer lower losses than vertically polarized waves, especially above 100 MHz. Antennas located near
dense rests should be horizontally polarized.
g. Directionality is the characteristic of an antenna that allows it to transmit and receive in a
specific direction. Other stations operating on the same or nearby frequencies may interfere with the
desired signal and make reception difficult or impossible. Reception of a desired signal can be
improved by using directional antennas. Horizontal half-wave antennas accept radio signals from all
directions, with the strongest reception being received in a line perpendicular to the antenna (broadside),
and the weakest reception being received from the direction of the antenna's ends. Changing the
antenna's
SS0131
1-6
axis so either end points directly toward the interfering source may eliminate or reduce interference.
Directional transmitting antennas concentrate radiation in a given direction and minimize radiation in
other directions. A directional antenna may be used to lessen enemy interception and interference with
friendly stations.
h. Since antennas are erected over the Earth and not out in free space, except for those on satellites,
the ground's presence alters the free space radiation patterns of antennas. The ground also affects some
of the electrical characteristics of an antenna. It has the greatest effect on those antennas that must be
mounted relatively close to the ground, in terms of wavelength. For example, medium and high
frequency antennas, elevated above the ground by only a fraction of a wavelength, will have radiation
patterns that are quite different from the free-space patterns.
i. Grounded antenna theory. The ground, a good conductor for medium and low frequencies, acts
as a large mirror for the radiated energy. This results in the ground reflecting a large amount of energy
that is radiated downward from an antenna mounted over it. Using this characteristic of the ground, an
antenna only a quarter-wavelength long can be made into the equivalent of a half-wave antenna. A
quarter-wave antenna erected vertically, with it's lower end connected electrically to the ground, as
shown in Figure 1-6, behaves like a half-wave antenna. Under these conditions, the ground takes the
place of the missing quarter-wavelength, and the reflections supply that part of the radiated energy that
normally would be supplied by the lower half of an ungrounded half-wave antenna.
j. There are several types of grounds.
(1) When grounded antennas are used,
the ground must have as high a conductivity as
possible.
This reduces ground losses and
provides the best possible reflecting surface for
the down-going radiated energy from the
antenna. At low and medium frequencies, the
ground acts as a sufficiently good conductor.
Thus, the ground connection must be made in
such a way as to introduce the least possible
amount of resistance to ground. At higher
frequencies, artificial grounds constructed of
large metal surfaces are common.
Figure 1-6. Quarter-wave antenna
connected to ground
(2) The ground connections take many forms, depending on the type of installation and the loss
that can be tolerated. In many simple field installations, the ground connection is made by driving one
or more metal rods into the soil. When more satisfactory arrangements cannot be made, ground leads
can be connected to existing devices that are grounded. Metal structures or underground pipe systems
are commonly
1-7
SS0131
used as ground connections. In an emergency, a ground connection can be made by forcing one or more
bayonets into the soil.
(3) When an antenna must be erected over soil with low conductivity, treat the soil with
substances that are highly conductive, when in solution, to reduce the soil’s resistance. Some of these
substances, listed in order of preference, are sodium chloride (common salt), calcium chloride, copper
sulphate (blue vitriol), magnesium sulphate (Epsom salt), and potassium nitrate (saltpeter). The amount
required depends on the type of soil and its moisture content. Please note that when these substances are
used, they must not get into nearby drinking water supplies.
(4) For simple installations, a single ground rod can be fabricated in the field from pipe or
conduit. A low resistance connection must be made between the ground wire and the ground rod. The
rod should be cleaned thoroughly by scraping and sandpapering at the point where the connection is to
be made, and a clean ground clamp should be installed. A ground wire can then be soldered or joined to
the clamp. This joint should be covered with tape to prevent an increase in resistance due to oxidation.
k. When an actual ground connection cannot be used because of the high resistance of the soil or
because a large buried ground system is not practical, a counterpoise can be used to replace the usual
direct ground connection.
(1) A counterpoise consists of a device made of wire that is erected a short distance above the
ground and insulated from it. The counterpoise’s size should be at least equal to or larger than the size
of the antenna.
(2) When the antenna is mounted vertically, the counterpoise should be made into a simple
geometric pattern; perfect symmetry is not required. The counterpoise acts as an artificial ground that
helps to produce the required radiation pattern. Figure 1-7 shows an RC-292 ground-plane antenna.
The three antenna elements pointing downward provide the counterpoise for this antenna.
(3) In some VHF antenna installations on vehicles, the metal roof of the vehicle or shelter is used
as a counterpoise for the antenna. Small counterpoises of metal mesh are sometimes used with special
VHF antennas that must be located a considerable distance above the ground.
s
SS0131
1-8
l. Depending on the type of antenna used,
radio energy radiated by an antenna forms an
electromagnetic field that has a definite pattern.
A radiation pattern shows the directional
characteristics of an antenna. A vertical antenna
(Figure 1-7) or a whip antenna on a vehicle
radiates energy equally in all directions
(omnidirectionally). A horizontal antenna, like
those used with RATT systems, is bidirectional.
Unidirectional antennas radiate energy in only
one direction. These radiation patterns do not
provide perfectly symmetrical coverage. There
are distortions in the patterns (back lobes and
side lobes) which are attributed to the antenna’s
physical characteristics and nearby obstructions
or terrain features. Three common radiation
patterns are shown in Figure 1-8, page 1-10.
The upper pattern is that of a quarter-wave
vertical antenna.
Note its omnidirectional
pattern. The center pattern shows a half-wave
horizontal pattern, located one-half wavelength
above the ground. RATT rigs use these longwire or doublet antennas. The bottom pattern is
that of a vertical half-rhombic antenna that
radiates in one direction.
Figure 1-7. RC-292 ground-plane antenna
m. An antenna’s length is related to the wavelength of the frequency used. An antenna has both a
physical length and an electrical length, and the two are never the same. Use the following formulas to
calculate the physical length of a half-wave long-wire antenna.
1-9
SS0131
Figure 1-8. Radiation patterns from quarter-wave,
half-wave, and vertical half-rhombic antennas.
As an example, a radio operator must design a long-wire (doublet) antenna for use with an AM radio,
tuned to 12 MHz. Using the formula:
The operator must measure the antenna 39 feet in length to operate at a frequency of 12 MHz. The
AN/GRA-50 antenna group is the most common antenna assembly used to erect a long-wire antenna.
Figure 1-9 shows the AN/GRA-50’s component parts. A very useful component is the tape measure,
which is graduated in both feet and meters. An operator lays out the antenna wire and measures the
required length. The electrical length of an antenna must be compatible with the frequency used. When
you change the frequency on the radio, the antenna matching unit mounted on the vehicle will
automatically change the electrical length of the whip antenna.
SS0131
1-10
Figure 1-9. AN/GRA-50 antenna group
5. Summary. In this lesson, you learned about the theory of antennas, including the principles of
antenna radiation, the characteristics of antennas, and the formulas used in antenna design.
a. Current flows in the antenna with an amplitude that varies with the generator voltage.
b. Two fields are established at an antenna (the induction field and the radiation field). The
radiation field is made up of an electric component and a magnetic component (electromagnetic).
c. Output from a transmitter is released at the antenna in the form of electromagnetic energy. At
the receiving antenna, electromagnetic energy is collected and converted into electrical energy, where it
d. Antenna reciprocity is the feature that allows an antenna to both transmit and receive radio
signals.
e. Antenna gain is the ratio between the amount of energy propagated in certain directions,
compared to the energy that would be propagated if the antenna were not directional. Antenna gain also
gives directional antennas greater transmission range than omnidirectional antennas for an equal signal.
f. The orientation of a radio wave's electric field in relation to the Earth is known as its
polarization. A radiated wave can be vertically, horizontally, or elliptically polarized.
g. Directionality is the characteristic of an antenna that allows it to transmit and receive in a
specific direction.
1-11
SS0131
h. The earth (ground) can be used as a conductor for radio frequencies.
i. A counterpoise is a conductor or system of conductors used as a substitute for a ground in an
antenna system.
j. Radiation patterns can be omnidirectional (all directions), bidirectional (two directions), or
unidirectional (one direction).
k. To calculate the physical length of a half-wave long-wire antenna, use the following formulas:
SS0131
1-12
1-13
SS0131
LESSON 1
PRACTICE EXERCISE
The following items will test your grasp of the material covered in this lesson. There is only one correct
answer for each item. When you complete the exercise, check your answers with the answer key that
follows. If you answer any item incorrectly, study again that part of the lesson which contains the
portion involved.
1.
Which statement describes antenna theory?
A.
B.
C.
D.
2.
A current flows in an antenna with
A.
B.
C.
D.
3.
A frequency
A wavelength
An amplitude
A polarization
Reciprocity
Polarization
Ground effect
Gain
A quarter-wave antenna erected vertically, with its lower half connected to the ground, operates
like what?
A.
B.
C.
D.
5.
that varies with the applied voltage.
The amount of energy propagated by an antenna in a certain direction, compared to the energy
propagated by that antenna if it were not directional, is called what?
A.
B.
C.
D.
4.
A moving electric field creates an electric field
A moving magnetic field creates a magnetic field
An antenna is not a radio system component
Current at any given point on the antenna will vary depending on the voltage
A directional antenna
A vertical antenna
A horizontal antenna
A half-wave antenna
Treating soil with salt will enhance what?
A.
B.
C.
D.
SS0131
Its resistance
Its conductivity
Its moisture content
Its density
1-14
6.
A counterpoise does which of the following?
A
B.
C.
D.
7.
Which radiation pattern does a whip antenna normally have?
A.
B.
C.
D.
8.
Unidirectional
Bi-directional
Omnidirectional
Elliptical
A signal team must construct a half-wave long-wire antenna for use with its AM radio, operating at
a frequency of 10 MHz. How long must the antenna be?
A.
B.
C.
D.
9.
Provides an artificial ground that helps to produce the required radiation pattern
Increases the transmitting range of the antenna
Increases signal attenuation
Ensures antenna reciprocity
4.68 meters
4.68 feet
46.8 meters
46.8 feet
What is the orientation of a radio wave's electric field in relation to the Earth?
A.
B.
C.
D.
Gain
Reciprocity
Polarization
Directionality
1-15
SS0131
LESSON 1
PRACTICE EXERCISE
ANSWER KEY AND FEEDBACK
Item
Correct Answer and Feedback
1.
D.
Current at any given point on the antenna will vary depending on the voltage
(page 1-2, para 2d)
2.
C.
An amplitude (page 1-3, para 2e(1))
3.
D.
Gain (page 1-4, para 4b)
4.
D.
A half-wave antenna (page 1-7, para 4i)
5.
B.
Its conductivity (page 1-8, para 4j(3))
6.
A.
Provides an artificial ground that helps to produce the required radiation pattern
(page 1-8, para 4k(2))
7.
C.
Omnidirectional (page 1-9, para 4l)
8.
D.
46.8 feet (page 1-9, para 4m)
9.
C.
Polarization (page 1-4, para 4c)
SS0131
1-16
1-17
SS0131
TACTICAL ANTENNAS
LESSON 2
TACTICAL ANTENNAS
01-5879.07.9001
OVERVIEW
LESSON DESCRIPTION:
In this lesson, you will learn about the types of tactical antennas and their radiation patterns. In addition,
you will learn about fabricating field expedient antennas using various repair techniques.
TERMINAL LEARNING OBJECTIVE:
ACTION:
Explain basic antenna theory.
CONDITION:
Given this lesson.
STANDARD:
To demonstrate competence, you must achieve a minimum of 70 percent on the
subcourse examination.
REFERENCES:
The material in this lesson was derived from FM 11-32, FM 11-64, FM 24-18,
FM 24-19, and TC 24-24.
INTRODUCTION
Tactical antennas are designed for efficiency and ease-of-use, and are ruggedized to take the abuse they
receive in the field. Some antennas are easy to use, such as a whip antenna that is used in high mobility
operations. Others, like directional antennas, require a working knowledge of antenna engineering. All
antennas either release or capture electromagnetic radiation.
2-1
SS0131
1. General. Most practical transmitting antennas are divided into two basic classifications-half-wave
antennas and quarter-wave antennas. An antenna operates some distance above the ground and may be
polarized either vertically or horizontally. A quarter-wave antenna operates with one end grounded.
Quarter-wave antennas are used both below and above 2 MHz. Half-wave antennas are used at the
higher frequencies (above 2 MHz).
2. Half-wave antenna. The half-wave antenna operates on the principle that the wavelength to which
any wire will electrically tune depends upon its physical length. It is center-fed. Its total wire length
equals a half of the wavelength of the signal to be transmitted. The maximum radiation emanates
perpendicular from the axis to the half-wave antenna. The half-wave antenna is also known as a
doublet, a dipole, or a Hertz antenna. It can be erected in a vertical, horizontal, or slanting position
between trees or with upright supports from a kit. The half-wave antenna is used for voice or RATT
messages when the tactical situation permit stationary operation. It is used for operating in the 2-to 30MHz frequency range, and it extends the signal range to 300 miles and beyond by using sky wave
propagation. The half-wave antenna operates at high frequencies when used on an aircraft or vehicle.
In such cases the aircraft or vehicle chassis becomes the effective ground for the antenna. The
AN/GRA-50 antenna group that is used in erecting a half-wave system is shown in Figure 2-1. Two
configurations for the AN/GRA-50 half-wave antenna are shown in Figures 2-2 and 2-3, pages 2-3 and
2-4.
Figure 2-1. AN/GRA-50 antenna group
SS0131
2-2
Figure 2-2. Half-wave doublet antenna with two upright supports
3. Whip antenna. The efficient half-wave antenna is not practical for use in mobile operations,
particularly with vehicular-mounted radio set. The whip is the most common antenna used for both
manpack and mobile vehicle operations. It is electrically short and vertically positioned. To achieve an
efficiency comparable to that of a half-wave antenna, the height of the vertical radiator should be a
quarter wavelength. To attain this, a loaded whip is used. This loading increases the electrical length of
the vertical radiator to a quarter wavelength. The other quarter wavelength of the antenna is supplied by
the ground, a counterpoise, or any conducting surface that is large enough. Some common whip antenna
applications are shown in Figure 2-4, page 2-5.
a. Whip antennas used with HF tactical radio sets can be as long as 15 feet, such as the whip used
on a RATT rig. The whip antenna provides an omnidirectional pattern during mobile operations. When
the RATT rig arrives at its destination, its crew switches to the half-wave antenna.
b. The whip antenna used with lightweight portable FM radios is 3 ft long for the semi-rigid steel
tape antenna and 10 ft long for the multisection whip antenna. It is shorter than a quarter wavelength to
keep it at a practical length. (A quarter wavelength antenna for 5 MHz would be over 46 feet long.) An
antenna tuning unit, built into the radio set or supplied with it, compensates for the missing antenna
length. The tuning unit (called a matching unit when mounted on the antenna) varies the electrical
length of the antenna to accommodate a range of frequencies.
2-3
SS0131
c. The whip antennas used with tactical
radio sets radiate an omnidirectional pattern in
the horizontal plane. This radiation pattern is
ideal for tactical operations because the stations
in a radio net will lie in random directions and
will frequently change their positions.
d. When a whip antenna is mounted on a
vehicle, the metal of the vehicle affects
antenna's operation. As a result, the direction in
which the vehicle is facing may affect
transmission and reception, particularly of
distant or weak signals. A vehicle with a whip
antenna mounted on the left rear side transmits
its strongest signal in a line running from the
antenna through the right front side of the
vehicle. Likewise, an antenna mounted on the
right rear side of the vehicle transmits its
strongest signal in a direction toward the left
front side. The best reception is obtained from
signals traveling in the direction shown by the
dashed arrows in Figure 2-5, page 2-6.
Figure 2-3. Half-wave doublet antenna
supported by trees
e. The best direction for transmission can often be determined by driving the vehicle in a small
circle until the best position is located. Normally, the best reception and transmission are achieved in
the same direction.
4. Ground-plane antenna. This antenna is a vertical quarter-wave antenna that is used to increase the
transmission and reception range of tactical FM radio sets. It uses radial elements (acting as a
counterpoise) that serve as the ground. The coaxial cable is connected with the inner conductor feeding
the vertical element, and the braid of the coaxial cable is connected to the radials (the ground-plane) to
keep them at ground potential. The ground-plane antenna is a broad-tuned type that radiates efficiently
over a wide range of frequencies. The two tactical ground-plane antennas in wide use throughout the
US Army are the RC-292 and the OE-254.
SS0131
2-4
Figure 2-4. Whip antennas
a. The RC-292 is a stationary, general-purpose, ground-plane antenna. The vertical radiating
element and the ground-plane elements must be changed to the proper length for different operating
frequencies. Its frequency range is between 20 and 76 MHz, and its planning range is about twice that
of a radio set using a quarter-wave whip antenna. The RC-292 antenna can be erected at various heights
up to 41 feet, depending on the number of mast sections used. Figure 2-6, page 2-7, shows an erected
RC-292 antenna.
b. The OE-254 broadband, omnidirectional VHF antenna system is replacing the RC-292. The OE254 antenna operates in the 30-to 88-MHz frequency range without the need to manually drop and
change out antenna elements. Its planning range is about 36 miles for average terrain. Like the RC-292,
the OE-254 can be erected at different heights, depending on the number of mast section used. An
erected OE-254 is depicted in Figure 2-7, page 2-7.
2-5
SS0131
Figure 2-5. Best directivity of whip antenna mounted on vehicle
5. Directional VHF log-periodic antenna.
a. This broadband, omnidirectional antenna provides an extended range and directivity for tactical
radios. It is used to communicate in the 30-to 88-MHz frequency range and does not require any
mechanical or electrical adjustments.
b. The log-periodic antenna can operate with either horizontal or vertical polarization. It has the
capability of changing polarization in less than one minute.
c. The highly directional radiation pattern of the log-periodic antenna provides very effective
electronic counter-countermeasures (ECCM) in a hostile electronic warfare (EW) environment. Since
its radiated energy is focused in one direction, less transmitter power is needed, further enhancing
ECCM.
d. This antenna can be erected in a geographical area no greater than 60 feet in diameter by two
soldiers in 20 minutes. Its mechanical azimuth can be changed within one minute. This antenna can be
mounted on a quick-erect mast either on a vehicle or a shelter, and transported by manpack or tactical
vehicle when fitted into two packages (one for the antenna and one for the mast).
SS0131
2-6
Figure 2-7. OE-254 ground-plane
antenna
Figure 2-6. RC-292 ground-plane
antenna
e. The log-periodic antenna is organic to battalion and higher level units for special applications. It
is primarily used by forward units in command and intelligence nets to a higher headquarters. Because
it is a directional antenna, its use is usually restricted to point-to-point communications.
f. Figure 2-8, page 2-8, illustrates the log-periodic antenna in three configurations.
6. VHF half-rhombic antenna OE-303.
a. The half-rhombic antenna is used mostly for special purposes by forward units over extended
distances on command and control and intelligence nets. The OE-303 antenna is a vertically polarized
antenna which, when used with the current VHF-FM tactical radios, considerably extends the
transmission range. It provides some degree of ECCM protection not offered by the current VHF-FM
omnidirectional antenna. When properly employed, the half-rhombic antenna decreases VHF-FM radio
susceptibility to hostile EW operations and enhances the communications ranges of the deployed radio
set. This effect is realized by directing the maximum signal strength in the direction of the desired
friendly unit.
SS0131
2-7
Figure 2-8. Log-periodic antenna
b. This high-gain, lightweight, directional antenna is capable of operating in the 30-to 88-MHz
frequency range without having to be physically tuned by the operator. Its highly directional pattern
makes it especially suited in providing point-to-point communications. It is oriented in the direction of
the desired transmission by using a compass and the appropriate map sheet.
c. The OE-303 antenna is rugged enough to withstand moving (erection and teardown) every four
to six hours. It can operate in harsh climatic conditions. It can be erected by two soldiers in 20 minutes
or less in a geographical area 175 ft in diameter or less, depending on the frequency used. This antenna
can be mounted on any structure about 50 feet in height, and is capable of azimuth directional change
within one minute. Mast assembly AB-1244 is the primary antenna support structure used with the halfrhombic VHF antenna. Using its mast assembly, this antenna is 30 feet high.
d. The antenna and all the ancillary equipment (guys, stakes, tools, mast sections) are contained in
two carrying bags for manpack or vehicular transportation. Figure 2-9 depicts the half-rhombic antenna.
SS0131
2-8
Figure 2-9. Half-rhombic VHF antenna
7. Near vertical incidence sky wave (NVIS). NVIS antenna AS-2259/GR is a lightweight sloping
dipole, omnidirectional antenna used with AM radios (AN/GRC-106) and improved high frequency
radios (IHFR)(AN/PRC-104A and AN/GRC-213/193A) that operate in the HF range of 2 to 30 MHz.
Like the doublet antenna, the NVIS is used when the tactical situation allows stationary operations. The
NVIS extends radio range up to 300 miles by using sky wave propagation. Polarized horizontally and
vertically at the same time, it can be erected by two soldiers in about five minuets. Figure 2-10, page 210, shows an operator using an NVIS antenna wit an AN/PRC-104A portable radio.
8. Combat net radio (CNR). CNR is designed around three separate radio systems--IHFR, SingleChannel Ground and Airborne Radio System (SINCGARS), and single-channel tactical satellite
a. The IHFR is replacing the older HF manpack (AN/PRC-70/74) and vehicular (AN/GRC-106)
radios. User-owned and operated, it employs both ground and sky wave propagation for short and
medium-range communications to pass voice and data signals. The IHFR uses the manpacked whip
antenna, the vehicle-mounted whip antenna, the AN/GRA-50 doublet antenna, and the AS-2259 NVIS
antenna.
2-9
SS0131
Figure 2-10. NVIS antenna
(1) The
AT-271A/PRC,
one type of collapsible whip
antenna for manpack operation, is
depicted in Figure 2-11. This
antenna is easily assembled and
broken down. The cord running
through the sections provides the
tension needed to keep them
together.
Figure 2-11. Collapsible whip antenna AT271 A/PRCC with antenna base
(2) The AS-3683/PRC, another
whip antenna used with the AN/PRC104A and the SINCGARS radios, is shown in Figure 2-12. This is a very flexible antenna especially
suited for use in thick brush or jungle. Its flexible goose-neck antenna base allows the operator to orient
it to obtain optimum reception. However, using the goose neck antenna base is optional.
SS0131
2-10
Figure 2-12. Flexible whip
antenna AS-3683/PRC
Figure 2-13. Vehicle-mounted
whip antenna
(3) A whip antenna used with the AN/GRC-213 in a vehicle-mounted configuration is shown in
Fig 2-13. When installed with the vehicle installation kit, this antenna is the most convenient to use
because it allows communications while the vehicle is moving and it has a omnidirectional (360°)
radiation pattern. It also requires no support except for the vehicle mount. A disadvantage is that its
propagation range is shorter than either the doublet or NVIS antennas.
b. SINCGARS operates in the VHF range.
(1) SINCGARS uses broadband antennas that do not have to be changed when frequencies are
changed, such as the OE-254 ground-plane and the AS-3900 and AS-3684 vehicular whip antennas.
The output frequency can change in a wide range between hops due to the frequency hopping nature of
SINCGARS. The narrow band RC-292 ground-plane antenna cannot be used.
2-11
SS0131
(2) Like the IHFR, SINCGARS uses the manpack whip antenna (AS-3683/PRC) for
communicating in heavy vegetation or when the transmitting range is deliberately limited. It also
operates using the AS-3684/VRC whip antenna, a 10-foot long antenna that consists of two antenna
elements and a matching unit base (Figure 2-14). The base spring allows the antenna to bend when it
strikes an obstruction
c. TACSAT operates in the UHF range.
The AN/PSC-3 and AN/VSC-7 communications
systems are lightweight, highly compact, and
deployable in quick-reaction situations where
extended communication range is essential to
mission effectiveness. They can operate on-themove/line-of-sight (LOS) at 2 watts or in the athalt/satellite mode at 35 watts. They can
transmit or receive in voice or data formats in
both modes. Figure 2-15 shows the AN/PSC-3
This medium gain, collapsible
parabolic antenna can be set up in minutes and
is highly reliable. The AN/VSC-7 TACSAT
radio set (Figure 2-16) used as a net control
station and is mounted in a tactical truck or an
S-280 communications shelter. It can serve up
to 15 AN/PSC-3 terminals in a communications
net with the selection of conference or
individual
call-codes.
Its
low-gain
omnidirectional whip antenna provides LOS.
The AN/VSC-7’s high-gain antenna enhances
transmission and reception.
9. UHF antennas. These highly directional
antennas are used with mobile subscriber
equipment (MSE) and the older multichannel
systems. They concentrate radiation in a given
direction and minimize radiation in other
directions. Their high directivity also aids in
obtaining a slight degree of transmission
security, making enemy direction finding more
difficult, and reducing noise and interference.
Figure 2-14. AS-3684/VRC
vehicular antenna
a. The corner-reflector (flyswatter) antenna consists of an adjustable reflector and an antenna
element. It is used in multichannel systems with radios that operate in the 200-to 1000-MHz range.
Highly directional, its reflector angle can be adjusted to operate on any frequency within its range. This
antenna is usually used with radio sets that have RF duplexing capabilities. The RF duplexer permits the
radio set to transmit and receive, using one coaxial cable between the antenna and the radio set. The
corner-reflector is shown is both vertical and horizontal polarization positions in Figure 2-17, page 2-14.
SS0131
2-12
b. The horn-type antenna is a directional
antenna with a modified dipole element
mounted in a ridge-loaded horn. The horn-type
antenna used in multichannel systems are
pyramidal (rectangular and flared in both
planes). The horn is designed to get the flare,
length, and aperture that will give the best
performance throughout the horn's entire
frequency range. This combination of flare,
length, and aperture emits a narrow beam of
high-intensity RF energy in the forward
direction. Horn antennas can be vertically or
horizontally polarized, and can be mounted in
pairs on the same mast or singularly on separate
masts. When used with a radio set having an
RF duplex, a single horn can be used to transmit
are used with some radio sets that operate on
frequencies from 601.5 to 1849.5 MHz. The
horn antenna is broadband and no adjustments
are made when changing frequencies. Elevation
or depression angles may be made at the
antenna's rear, as needed. A rear view of a pair
of horn-type antennas mounted in a vertical
polarization is shown in Figure 2-18, page 2-14.
Figure 2-15. AN/PSC-3 TACSAT radio set
Figure 2-16. AN/VSC-7 TACSAT
2-13
SS0131
Figure 2-17. Typical corner reflector antenna
Figure 2-18. Typical horn-type antenna
SS0131
2-14
c. The parabolic reflector antenna consists of a saucer-like reflecting surface (parabola) and a
dipole (feed device) placed at its focal point. There are numerous types of reflector antennas used,
depending on the frequency. The MSE LOS radios use parabolic reflector antennas mounted on 15meter masts. Figure 2-19 shows two examples of parabolic antennas.
Figure 2-19. Parabolic reflector antennas
10. Field repair and expedients. Antennas are sometimes broken or damaged, resulting in failed or poor
communications. In the days before cable television, viewers at home received a TV signal through an
antenna, either strapped to the chimney or sitting on top of the set. If the antenna was missing or
broken, an expedient loop antenna could be fashioned from a simple coat hanger. Reception was not the
best, but it was tolerable. Remember, as a signal officer, your job is to get the message through.
Knowing how to do a field expedient repair job may come in handy some day. The following antenna
repair techniques have been proven to work.
a. Metallic whip antennas.
(1) Should a whip antenna break into two sections, you can lash the two sections together to
provide a good mechanical connection. To ensure essential electrical
2-15
SS0131
conductivity, scrape the paint off of each
section's end and tie them together with stripped
field wire (WD-1). Solder the connection if you
have the time and equipment. Place a stick,
pole, or branch on each side of the break and
wrap the splint tightly with field wire, rope, or
tape, as shown in Figure 2-20.
(2) If you lose your antenna and are left
with just a stub, you can use another repair
method to get back on the air. If the missing
section is about 6 feet long, just find a pole the
same length and lash it to the stub. Scrape off
the paint from the top 2 inches of the whip's
stub and wrap about 12 inches of bare wire
around the stub's scraped portion. Wrap it tight
and tape it securely. Attach a length of WD-1
along the pole's length with tape. The total
length of the upright WD-1 and antenna stub
should be the same length as the length of the
original antenna. This antenna will not take
much abuse, but it will send and receive signals.
Figure 2-21 illustrates this technique.
Figure 2-20. Spliced metallic whip antenna
b. Vertical antennas transmit and receive
omnidirectionally. Most tactical antennas used
for vehicular and manpack radios are vertical.
A vertical antenna can be improvised by using a
metal pipe or rod of the correct length, held
erect by guy lines. The antenna’s lower end is
insulated from ground by placing it on
insulating material. Figure 2-22 shows vertical
antennas made of wire and supported by a tree
and a wooden pole. If the vertical mast is not
long enough to support the wire upright, the
connection can be modified at the antenna’s top,
as shown in Figure 2-23.
Figure 2-21. Spliced metallic whip antenna
using WD-1 as part of the antenna
SS0131
2-16
Figure 2-22. Field substitutes for support of
vertical wire antennas
Figure 2-23. Additional means of supporting vertical
wire antennas
2-17
SS0131
c. The electrical length of an end-fed, half-wave antenna is measured from the antenna terminal on the
radio set to the antenna's far end. For optimum performance, the antenna should be constructed longer
than necessary, and shortened as required until the best results are achieved. The ground terminal of the
radio set should be connected to a good Earth ground for this antenna to operate efficiently. This
antenna is depicted in Figure 2-24.
Figure 2-24. End-fed half-wave antenna
d. The center-fed doublet antenna is a half-wave antenna consisting of two quarter-wavelength
sections on each side of the center (Figure 2-25). Doublet antennas are directional broadside to their
length; this makes the vertical doublet antenna essentially omnidirectional. The horizontal doublet
antenna is bidirectional. A center-fed half-wave FM antenna can be supported by a wooden frame,
shown in Figure 2-26. View A shows a horizontal antenna, and view B shows a vertical antenna. These
antennas can be rotated to any position to obtain the best performance. If the antenna is erected
vertically, the transmission line should be brought out horizontally from the antenna for a distance equal
to at least one-half of the antenna’s length before it is dropped down to the radio set.
e. Two field-expedient directional antennas are the vertical half-rhombic antenna (Figure 2-27,
page 2-20) and the long-wire antenna (Figure 2-28, page 2-20). These antennas consist of a single wire,
preferably two or more wavelengths long, supported on poles at a height of 3 to 7 meters (10 to 20 feet)
above the ground. If needed, the antennas will operate satisfactorily as low as 1 meter (about 3 feet)
above the ground. The wire's far end is connected to ground through a noninductive 500-to 600-ohm
resistor. To ensure that the transmitter's output power will not burn out the resistor, a resistor rated at
least one-half of the transmitter's wattage output should be used. A reasonably good ground, such as a
number of ground rods or a counterpoise, should be used at both ends of the antenna. The radiation
pattern is directional. These antennas are used primarily for transmitting or receiving HF signals.
SS0131
2-18
Figure 2-25. Half-wave doublet antenna
Figure 2-26. Center-fed half-wave antenna
2-19
SS0131
Figure 2-27. Vertical half-rhombic antenna
Figure 2-28. Long-wire antenna
SS0131
2-20
f. The V antenna
(1) This antenna consists of two wires
forming a V, with the open area of the V
pointing toward the desired direction of
transmission or reception (Figure 2-29). An
easier way of constructing this antenna is to
slope the legs downward from the apex of the
V; this is called a sloping-V antenna (Figure 230).
(2) The angle between the legs varies
with the length of the legs in order to achieve
minimum performance. Table 2-1, page 2-22,
can be used to determine the angle and the
length of the legs.
Figure 2-29. V antenna
(3) When this antenna is used with more
than one frequency or wavelength, an apex
angle is used that is midway between the
extreme angles determined by the chart.
(4) To make the V antenna radiate in
only one direction, noninductive terminating
resistors are added from the end of each leg (not
at the apex) to ground. The resistors should be
approximately 500 ohms and have a power
rating at least half that of the output power of
the transmitter being used. The antenna will
radiate bidirectionally, both front and back
without the resistors.
Figure 2-30. Sloping-V antenna
2-21
SS0131
Table 2-1. Leg angle for V antennas
11. Safety. Soldiers are still occasionally killed or seriously injured a result of antenna accident, in spite
of repeated safety warnings tough briefings, publications, and messages. As a signal officer, you should
develop a keen sense of field safety, especially as it relates to signal operations. If you know an antenna
is too close to a power line, insist that it be dropped and moved. Safety tips and warnings that are found
in many signal-related publications are shown in Figures 2-31 and 2-32, pages 2-24 and 2-25,
respectively. Study these safety tips and warnings and think back to experiences you have had during
previous operations. Have you violated any of these warnings? If the answer is no, you are to be
commended for your good approach to safety. If the answer is yes, then resolve to heed the warnings
henceforth.
12. Summary. In this lesson, you learned about the types of tactical antennas, their radiation patterns,
and how to fabricate field-expedient antennas using various repair techniques.
a. The half-wave antenna is also called a doublet, a dipole, or a Hertz antenna. It is center-fed. Its
total wire length is one half of the wavelength of the signal to be transmitted.
b. The whip antenna provides an omnidirectional radiation pattern. It is a quarter-wave antenna
used for manpack and vehicular operations.
c. The ground-plane antenna is a vertical quarter-wave antenna that increases the range of tactical
FM radio sets. Its radial elements provide a counterpoise that simulates a ground. The older RC-292
has radial elements that must be changed accordingly with frequency changes. The OE-254 does not
require any changes in elements when frequencies change.
d. The log-periodic antenna is very directional and is usually used in point-to-point
communications.
SS0131
2-22
e. The half-rhombic antenna OE-303 provides an extended range and affords some ECCM
protection (not omnidirectional).
f. The NVIS is a sloping dipole that gives an omnidirectional pattern for AM radios. It can extend
the range up to 300 miles.
g. The two CNR antennas are the AT-271A/PRC, a collapsible whip for manpack operations, and
the AS-3683/PRC, a flexible antenna used in areas of heavy vegetation.
h. The three SINCGARS antennas are the OE-254, the AS-3684/VRC (vehicular mounted), and the
AS-3683/PRC.
i. The two TACSAT antennas are the collapsible parabolic reflector for the AN/PSC-3 and the
omnidirectional whip antenna for the AN/VSC-7.
j. There are several UHF antennas.
(1) The corner-reflector (flyswatter) antenna is highly directional and is used with multichannel
systems.
(2) The horn-type antenna is another antenna used in multichannel systems. The flared design
serves to direct the RF energy in a highly directional pattern.
(3) The parabolic reflector antenna has a reflecting surface and a dipole at its center. The
reflector is used to capture or release signals.
k. There are several field expedient antennas.
(1) Metallic whip. Broken whips can be lashed together using WD-1, rope, and tape. If part of
the antennas is missing, field wire can be used as the radiating element.
(2) Directional antennas. The vertical half-rhombic and the long-wire antennas are used for
transmitting and receiving HF signals.
(3) V antenna. It is made of two wires forming a V with the open end pointing toward the
direction of transmission. Using a resistor changes the V antenna from bidirectional to unidirectional.
2-23
SS0131
Figure 2-31. Safety tips
SS0131
2-24
Figure 2-32. Safety warning
2-25
SS0131
LESSON 2
PRACTICE EXERCISE
The following items will test your grasp of the material covered in this lesson. There is only one correct
answer for each item. When you complete the exercise, check your answer with the answer key that
follows. If you answer any item incorrectly, study again that part of the lesson which contains the
portion involved.
1.
Which statement describes the half-wave antenna?
A.
B.
C.
D.
2.
What should be the height of the vertical radiator of a whip antenna?
A.
B.
C.
D.
3.
Directional VHF
Bidirectional VHF
Omnidirectional FM
Omnidirectional AM
Which statement describes the unidirectional log-periodic antenna?
A.
B.
C.
D.
5.
A quarter wavelength
A half wavelength
A full wavelength
Two wavelengths
The RC-292 and OE-254 are what type of antennas?
A.
B.
C.
D.
4.
It is used at lower frequencies
It cannot be used on a vehicle
Unlike the quarter-wave antenna, it is not center fed
It can extend the signal range to 300 miles and beyond using sky wave propagation
It operates in the 30- to 90-MHz frequency range
Its radiation pattern provides very effective electronic countermeasures
It provides an extended range for tactical radios
Its radiated energy is not focused in one direction
The NVIS antenna uses what type of polarization?
A.
B.
C.
D.
SS0131
Vertical only
Elliptical and horizontal
Elliptical and vertical
Horizontal and vertical
2-26
6.
Which characteristic describes the antenna matching unit?
A.
B.
C.
D.
7.
Which statement describes antenna use by SINCGARS?
A.
B.
C.
D.
8.
2
3
20
35
Which statement describes the horn-type antenna?
A.
B.
C.
D.
10.
The RC-292 can extend the range of the SINCGARS systems up to 36 miles
SINCGARS uses broadband antennas
SINCGARS cannot use the AS-3683/PRC antenna
SINCGARS antennas have to be changed with changing frequencies
The AN/PSC-3 TACSAT system can transmit up to how many watts in the at-halt mode?
A.
B.
C.
D.
9.
Changes the modulation from AM to FM
Matches the frequency to the radiation pattern
Varies the electrical length of the antenna to accommodate a range of frequencies
Varies the electrical length of the antenna to accommodate a change in radiation pattern
It must be adjusted each time the frequencies are changed
It is a directional antenna
It can only be horizontally polarized
Elevation angles may be made at its front, as needed
Which statement describes antenna use?
A.
B.
C.
D.
A vertical half-rhombic antenna does not have a directional radiation pattern
A long-wire antenna has a directional radiation pattern
A vertical half-rhombic antenna can operate as low as 2 feet above the ground
A long-wire antenna is used primarily for transmitting EHF signals
2-27
SS0131
LESSON 2
PRACTICE EXERCISE
ANSWER KEY AND FEEDBACK
Item
Correct Answer and Feedback
1.
D. It can extend the signal range to 300 miles and beyond using sky wave
propagation (page 2-2, para 2)
2.
A. A quarter wavelength (page 2-3, para 3)
3.
C. Omnidirectional FM (page 2-4, para 4)
4.
C. It provides an extended range for tactical radios (page 2-6, para 5a)
5
D. Horizontal and vertical (page 2-7, para 6)
6.
C. Varies the electrical length of the antenna to accommodate a range of
frequencies (page 2-3, para 3b)
7.
B. SINCGARS uses broadband antennas (page 2-11, para 8b(1))
8
D. 35 (page 2-12, para 8c)
9.
B. It is a directional antenna (page 2-13, para 9b)
10.
B. A long-wire antenna has a directional radiation pattern (page 2-18, para 10e)
SS0131
2-28
```