luxCONTROL lighting control system basicDIM basicDIM DGC Compact control module Product description •Compact dimensions for luminaire installation •For up to 20 DSI or DALI devices (max. 10 per output channel) •DALI IN input •2 DALI/DSI output channels with adjustable offset from channel 2 to channel 1 •1 relais output •Sensor input for up to 4 basicDIM DGC sensors 5DPI 14 •2 switch inputs for on/off switching and dimming •Individual adjustment of the parameters with basicDIM DGC Programmer or software masterCONFIGURATOR •5-year guarantee È Wiring diagrams and installation examples, page 9 Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 1 luxCONTROL lighting control system basicDIM basicDIM DGC Compact control module Technical data Mains frequency 50 / 60 Hz Power 2.5 W Stand-by power 0.5 W Current draw, input (DALI bus) 2 mA Operating temperature 0 ... +60 °C Storage temperature -25 ... +70 °C Type of protection IP20 Max. casing temperature tc 70 °C 159 147–150 30 220 – 240 V 21 30 Rated supply voltage Ordering data Type Article number Mounting basicDIM DGC 28000920 Luminaire installation 10 pc(s). Packaging carton Specific technical data Type Inputs Outputs CH2 as Link Line Dimming Max. cable Max. basicDIM Max. sensor Digital control Control output Dimming Maximum switch length at DGC sensors line length at line DALI/DSI per physical range cable length 1.5 mm² 0.2 – 1.5 mm² output (devices) at 1.5 mm² basicDIM DGC double 100 m 4 10 m 2 10 1 – 100 % 100 m Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com Voltage DC 13 V Output, relay (L‘) Maximum Number of Max. switching Maximum Max. cable length combinable output (e.g. apparent switching at 1.5 mm² modules LCAI) power output 100 m 10 2 200 VA 500 W 2 ACCESSORIES luxCONTROL lighting control system basicDIM basicDIM DGC Sensor 5DPI 14f Product description •Light measurement and motion detection •Up to 4 basicDIM DGC sensors on one basicDIM DGC •Can be remote controlled •Light measurement and motion detection can be deactivated •Individual adjustment of the parameters with basicDIM DGC Programmer or software masterCONFIGURATOR •Power supply via basicDIM DGC no Detection angle 360° Light measurement at the sensor head 1 10 – 650 lx Infra-red control range 5m Max. mounting height 5m Operating temperature 0 ... +50 °C Storage temperature -25 ... +55 °C Type of protection IP20 1 The measured value at the sensor head corresponds to approx. 15 to 2,000 lux on the 44,4 2 4m Swivel design 12,8 Ø of detection range, mounted at a height of 2.5 m 16,4 Technical data Ø13,9 1,9 3 surface measured. Ordering data Type Article number Packaging, carton basicDIM Sensor 5DPI 14f Luminaire installation 28000933 40 pc(s). Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 3 ACCESSORIES luxCONTROL lighting control system basicDIM basicDIM DGC Sensor 5DPI 14rc Product description •Light measurement and motion detection •Up to 4 basicDIM DGC sensors on one basicDIM DGC •Can be remote controlled •Light measurement and motion detection can be deactivated •Individual adjustment of the parameters with basicDIM DGC Programmer or software masterCONFIGURATOR •Power supply via basicDIM DGC 4m Swivel design no Detection angle 360° Light measurement at the sensor head 1 10 – 650 lx Infra-red control range 5m Max. mounting height 5m Operating temperature 0 ... +50 °C Storage temperature -25 ... +55 °C Type of protection IP20 5,5 Ø of detection range, mounted at a height of 2.5 m 65,4 Technical data 1 The measured value at the sensor head corresponds to approx. 15 to 2,000 lux on the surface measured. Ø46,75 Ø58 128 Ordering data Type Article number Packaging, carton basicDIM Sensor 5DPI 14rc Ceiling installation 28000934 63 pc(s). Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 4 ACCESSORIES luxCONTROL lighting control system basicDIM basicDIM DGC Programmer Product description •Optional infra-red programming unit for basicDIM DGC •Setting of predefined discrete parameter values •Programmable functions such as light level, time delay, P.I.R., bright-out, power up ACCESSORIES Ordering data Type Article number Dimensions L x W x H Packaging carton basicDIM DGC Programmer 28000646 130 x 56 x 15 mm Type Article number Dimensions L x W x H Packaging carton REMOTECONTROL IR6 28000647 86.5 x 40.5 x 7.2 mm 500 pc(s). 1 pc(s). REMOTECONTROL IR6 Product description •Optional infra-red remote control •Switching on and off (On/Off button) •Dimming (Up/Down button) •Activation of automatic lighting control •Setting the threshold control point (Set button) Ordering data Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 5 ACCESSORIES luxCONTROL lighting control system basicDIM Strain-relief set Product description 21 •5-year guarantee 50 234 Ordering data Type Article number Packaging carton Strain-relief set 28000881 10 pc(s). Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 6 luxCONTROL lighting control system basicDIM Standards EN 55015 EN 61000-3-2 EN 61347-1 EN 61347-2-11 EN 61547 EN 62386-101 EN 60598-1 EN 62493 basicDIM DGC The basic DIM DGC provides the basis for an easy-to-use and cost-effective lighting system with motion detection. When the sensor detects movement it triggers a individual adjustable motion detection profile in the control unit. As the amount of natural ambient light changes the illuminance from the artificial lighting system is adjusted. The connected luminaires can be switched on and off via momentary-action switch or remote control possible. Glow-wire test according to EN 61347-1 passed. The DALI IN interface allows integration of the basicDIM DGC module also into a comfortDIM system. The basicDIM DGC module has 5 preprogrammed profiles which can be selected using the basicDIM DGC Programmer. The profiles can be adjusted to your application via the masterCONFIGURATOR (≥ V2.12) software. DALI standard The basicDIM DGC is designed to control control gear with DALI standard IEC 60929 (DALI V0) and IEC 62386 (DALI V1). If the basicDIM DGC module is used in the basic application, the CH2 can be used as control channel for controlling subordinate basicDIM DGC modules (basic connection), so that the controlling and the subordinate basicDIM DGC modules can be programmed and allocated to groups using the masterCONFIGURATOR software. Every single basicDIM DGC module can be allocated to a group and respond to the presence of up to 5 groups (for more detailed information please refer to the masterCONFIGURATOR documentation). Installation •basicDIM DGC can be operated without sensor. The motion detection must be disabled via masterCONFIGURATOR or with unique connecting a sensor and basicDIM DGC Programmer. •DSI/DALI is not SELV. The installation instructions for mains voltage therefore apply. •The maximum cable length between the external switch and basicDIM DGC is 100 m. •The maximum cable length between the sensor and basicDIM DGC is 10 m. •A synchronous operation of DALI and DSI ballasts at the same control gear is not possible. •The output channels (for a cable cross-section of 1.5 mm2) must not be exceeded 100 m. •If CH2 is used as link line, the maximum cable length must not exceed 100 m (at 1.5 mm²). •If a basicDIM DGC is connected to CH2, DALI IN is disabled and CH2 is used as Link-Line (neighbourhood function). No control commands are transmitted via CH2, to reactivate DALI IN see basicDIM DGC manual. • Any number of push to make switches may be connected in parallel to the inputs. •Do not connect standard switches to the input. •Please ensure that the detection range of the sensor lies in the lighting area of the controlled luminaires. • Heaters, fans, printers and copiers located in the detection zone may cause incorrect presence detection. • To avoid false readings, the sensor should be installed so there is no direct light from the lamp in the detection zone. • Sensor wires must be routed separately from the lamp wires and mains cables otherwise the lighting control system may malfunction. If separate routing is not possible (for reasons of space) shielded lamp wires and mains cables must be used. Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 7 luxCONTROL lighting control system basicDIM basicDIM DGC sensor Light level recognition area Presence / motion detection Sensor alignment x2 Example for light and motion detection area at height of 1.7 m: y x2 y x1 y y 1m x1 y αx2 = 22° αx1 = 38° 0.7 m h α = 78° h αy = 30° x1 x2 1.3 m h 22° 38° y x2 y x1 y Light level recognation area d 1m Presence / motion detection x2 y 2.8 m y x1 x2 y y x1 h* x1 x2 y d 1.7 m 1.3 m 0.7 m 1.0 m 2.8 m 2.0 m 1.6 m 0.8 m 1.2 m 3.2 m 2.3 m 1.8 m 0.9 m 1.3 m 3.7 m 2.5 m 2.0 m 1.0 m 1.4 m 4.0 m 2.7 m 2.1 m 1.1 m 1.6 m 4.4 m 3.0 m 2.3 m 1.2 m 1.7 m 4.9 m 3.5 m 2.7 m 1.4 m 2.0 m 5.7 m 4.0 m 3.1 m 1.6 m 2.3 m 6.5 m * The recommended maximum room height for office applications is 3 m and for corridor applications for example 4 m. Up to 2 m mounting height presence is detected and over 2 m motion is detected. Calculation of the diameter (light area): x1 = tan(ax1) × h x2 = tan(ax2) × h y = tan(ay) × h Calculation of the diameter (motion area): d = 2 × tan(0,5 × a) × h Mounting variants luminair installation sensor Size of the sheet: 0.8 – 1.8 mm Size of the sheet: 0.6 – 0.8 mm 1,5 – 2,5 ø14,1+0,2 0 2,2 +0,2 0 19,1 20 +0,1 -0,1 4 +0,2 0 ø1,8 +0,1 0 0 3,2 -0,15 Size of the sheet: 0.8 – 3.0 mm 3,3 – 5,5 14,1+0,2 0 41,1+0,2 0 R1,9 0-0,2 Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 8 luxCONTROL lighting control system basicDIM Wiring diagram basicDIM DGC DALI L N DA DA 2 3 4 6 DA 7 DA 2 3 4 6 DA 7 DA Uconverter LCAI 2 3 4 Uconverter LCAI 6 DA 7 DA max. 500 W (L') L N L’ * T1 T2 max. 10 basicDIM DGC Sensor max. 4 Uconverter LCAI max. 10 eD1 Sensor eD2 basicDIM DGC DA DALI IN DA CH1 2 3 4 D1 D2 D1 CH2 D2 6 DA 7 DA Uconverter LCAI max. 64 DGC * must be the same phase as for L Relais in standby L N L’ DA DA max. 10 basicDIM DGC Sensor 2 3 4 The inrush currents of the control gears must be taken into account when dimensioning the contactor. 6 DA 7 DA max. 4 L N L’ * T1 T2 Uconverter LCAI max. 10 eD1 Sensor eD2 basicDIM DGC DA DALI IN DA CH1 D1 D2 D1 CH2 D2 2 3 4 6 DA 7 DA Uconverter LCAI max. 64 DGC * must be the same phase as for L Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 9 luxCONTROL lighting control system basicDIM Wiring type and cross-sections for basicDIM DGC Solid wire with a cable cross-section of 0.5 mm² to 1.5 mm². DALI IN The DALI IN interface allows integration of the basicDIM DGC module also into a comfortDIM or other BMS systems. However, not all DALI commands are supported. The DALI commands supported are listed in the operating instructions. wire preparation: 0.5 – 1.5 mm² By using the DGC in basic configuration (additional DGC‘s connected to CH2) DALI IN interface will be deactivated. 8.5 – 9.5 mm Wiring type and cross section basicDIM Sensor 5DPI 14rc The wiring can be solid wire or stranded wire with a cross-section of 0.2 mm² to 1.5 mm². DALI/DSI output channels CH1 - CH2 The output channels can be set to DSI or DALI (default) using the basicDIM DGC Programmer or the masterCONFIGURATOR software. wire preparation: 0.2 – 1.5 mm² 7.5 – 8.5 mm Wiring type and cross section basicDIM Sensor 5DPI 14f The wiring can be solid wire or stranded wire with a cross-section of 0.2 mm² to 0.5 mm². After mains failure the basicDIM DGC will set new the following parameters to CH1/CH2: POWER ON LEVEL SYSTEM FAILURE LEVEL FADE TIME MIN LEVEL MAX LEVEL For more detailed information please refer to the manual. wire preparation: 0.2 – 0.5 mm² 7.5 – 8.5 mm Switch basicDIM DGC has two inputs (T1 and T2) for two external switches. Any number of switches can be connected in parallel to the inputs (parallel connection of T1 and T2 possible). Short press (< 500 ms): ON/OFF Long press (> 500 ms): Dim up/down A change in the light value deactivates lighting regulation only temporarily. As soon as the luminaire has been automatically switched on again (motion detection) or manually switched off and on again, regulation is activated again. 2 x short press: The overwritten setpoint light value is stored (luminaire acknowledges by flashing twice) Function is lockable via the DSI programmer Different output channels are controlled, depending on the profile selected. Relais The relay can be used in four different operating modes: •Reduction of standby losses (standby wiring example) •Independent output channel for switching non-dimmable luminaires (DALI wiring example) Depending on the profile used, the relay will respond differently. For the 5 main profiles, the two relay profiles used are Standby and OnlyOFF. The masterCONFIGURATOR software allows to enable or disable the relay profiles as well. Standby Standby OnlyOFF Energy saving mode If the basicDIM DGC module is switched off, the relay will switch off (after 10 minutes). If the basicDIM DGC is switched on, the relay will switch on. Switching: relay in standby mode The relay must be switched on using the momentary-action switch, but is switched off by the presence detector. Only OFF Active The relay is switched on or off via the presence detector. Inactive The relay must be switched on and off using the momentary-action switch. Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 10 luxCONTROL lighting control system basicDIM Depending on the profile used, different operating modes are preprogrammed for the presence detector. These can be changed using the basicDIM DGC Programmer or the masterCONFIGURATOR software. ON OFF only OFF ∞ ON / OFF The light is switched on and off automatically based on the presence/absence of people. Only OFF The presence detector just switches the connected luminaires off. The luminaires are switched on manually via the connected external momentary-action switch or the remote control. Never OFF If no presence is detected, the sensor dims down to the “second light level” parameter and maintains this setting. OFF Presence detector disabled. The light must be switched on and off manually. OFF Manual-off delay If the light is switched off manually via momentary-action switch or remote control, the presence detector is disabled. After a period of delay without any presence detected, the presence detector is enabled again. If the sensor detects presence during the “Manual Off” delay, the delay time will start all over again. Lighting control AUTO Lighting control is started via the Auto key of the basicDIM Programmer or REMOTECONTROL IR6. If the basicDIM DGC module has been switched on via the ON key, lighting control is disabled. If you want to use lighting control, you need to start the DGC module via the Auto key. Run-on time 1 min 10min 20min AUTO Run-on time of the presence detector, run-on time starts when no presence is detected. The run-on time may vary depending on the profile used. You can choose whether you want the basicDIM DGC module to switch off the light completely or to dim it down to the absence value after the run-on time. It can also be changed using the basicDIM DGC Programmer or the masterCONFIGURATOR software. Absence value 1% 10% 30% Lighting control can also be disabled using the masterCONFIGURATOR software. Set target value SET The light level can be set via following options: • REMOTECONTROL IR6 (press the key for > 3 s) • basicDIM DGC Programmer (press the key for > 3 s) • masterCONFIGURATOR software • external momentary-action switch: Switch-off delay 0min 1 min 10 min 1 min SET ∞ 30min The absence value (light level) and the switch-off delay (the period for which the level is maintained) differ depending on the profile used; these parameters may be changed using the basicDIM DGC Programmer or the masterCONFIGURATOR software. ON By briefly pressing the momentary-action switch twice the currently measured light level is saved as new target value. (Depending on the profile used, this function is enabled or disabled, but it can be changed using the basicDIM DGC Programmer or the masterCONFIGURATOR software) Bright-out Offset ON OFF - 30% Depending on the profile used, a negative offset may be enabled between CH2 and CH1. Using the basicDIM DGC Programmer and the masterCONFIGURATOR software, this parameter may be changed (also positive offset possible). CH2 40 % CH1 70 % If the nominal illuminance level (e.g. 500 lx) is exceeded for 10 minutes at over 150 % (e.g. 750 lx), the light is switched off, even if presence is detected. The light is switched on again as soon as the measured light level falls below the target value. Depending on the profile used, this function is either enabled or disabled and can be changed using the basicDIM DGC Programmer or the masterCONFIGURATOR software. The bright-OUT status can be indicated on the sensor by a slowly flashing green status LED. By default this function is disabled, but it can be enabled using the masterCONFIGURATOR software. 500 LUX Artificial light Natural light CH1 ON CH2 OFF Light control incl. brightout activated for CH1. CH2 is not illuminated controlled. Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 11 luxCONTROL lighting control system basicDIM Neighbourhood function Depending on the profile used, the basicDIM DGC can respond to presence detected in other groups. These functions can be changed using the basicDIM DGC Programmer or the masterCONFIGURATOR software. Switched off Behaviour after return of power The basicDIM DGC module features two different types of starting behaviour after mains failure. No response to presence detected in other groups. Default setting for all profiles! OFF Switched on If presence is reported by other groups, the light level will switch to presence value ON Switched on If presence is reported by other groups, the light level will switch to absence value OFF ON Power ON behaviour OFF (luminaires remain switched off) Power ON behaviour ON (the luminaires are switched on after return of power). Default setting for all profiles! Momentary-action switch inputs Momentary-action switch 1 T1 Momentary-action switch 2 T2 CH1 CH2 CH1 CH2 Display of outputs controlled by momentaryaction switch (CH1 and CH2, or just CH1 or CH2) Basic functions ON OFF Switching on If the DGC module has been switched on via ON, lighting control is disabled. Switching off Dimming up Dimming down Profiles Profile 1: Individual room Profile 2: Classroom Profile 3: Corridor Profile 4: WC Profile 5: Free-standing luminaire (default profile) Profile Test: You may use the Profile Test to check the profile you selected. All times relevant to the profile are reduced to 15 s. The Profile Test will automatically be terminated after 1 h, or by pressing the Auto key of the basicDIM DGC Programmer. The profiles can be adjusted to your needs via the masterCONFIGURATOR software or the DGC Programmer. For more detailed information please refer to the masterCONFIGURATOR documentation at www.tridonic.com. Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 12 luxCONTROL lighting control system basicDIM Brief description of profiles Individual room profile T1 CH1 T2 CH2 ON OFF ON OFF ON OFF ON OFF OFF ON OFF SET ON Standby ON - 30% Only OFF ON - 30% Standby ON Only OFF CH1 ON CH2 OFF 10min 10% 20min 10 min 1 min 10% 20min 1 min 10min 10% 1 min 10 min ∞ 1 min 1 min 10 min SET ON Classroom profile T1 CH1 CH2 T2 only OFF Corridor profile T1 CH1 CH2 ON T2 CH1 CH2 ON CH1 CH2 ON ON OFF WC profile T1 OFF ON OFF ON T2 Free-standing luminaire profile (default) T1 T2 CH1 CH2 ON OFF ON OFF ON OFF SET ON Standby CH1 ON CH2 OFF SET ON Data sheet 03/16-CO074-11 Subject to change without notice. www.tridonic.com 13
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021