Sangean | DCR-200 | Operating instructions | Sangean DCR-200 Operating instructions

Sangean DCR-200 Operating instructions
DCR-200
GB
Rersion 1
Table of Contents
Important safety instructions .............................................. 2-3
Introduction .............................................................................. 4
Controls and connections .................................................... 5-8
Display icons ............................................................................. 9
Using the Digital Receiver for the First time ....................... 10
Operating Your Digital Receiver – DAB ........................ 11-12
Display Modes – DAB ...................................................... 13-14
Finding New Stations – DAB ................................................. 15
Manual Tuning – DAB ............................................................ 16
Dynamic Range Control (DRC) settings – DAB ................ 17
Operating your digital receiver – Search tuning FM ......... 18
Manual tuning – FM ............................................................... 19
Display Modes – FM .............................................................. 20
FM Stereo / mono ................................................................... 21
Presetting Stations in DAB and FM modes ....................... 22
Recalling a Preset in DAB and FM modes ........................ 23
Clock and Alarms .............................................................. 24-31
Display and Audio ............................................................. 32-36
Information ......................................................................... 37-39
1
Important Safety Instructions
GB
1. Read and understand all safety and operating instructions before the
radio is operated.
2. Retain instruction: The safety and operating instructions should be
retained for further reference.
3. Heed warnings. All warnings on the appliance and operating
instructions should be followed.
4. Follow all operations and use instructions.
5. Water and moisture: The appliance should not be used near water.
Do not use near a bathtub, washbowl, laundry tub, kitchen sink,
wet basement, swimming pool, etc.
6. Unplug the radio from the AC power outlet before cleaning. Use only a
damp cloth for cleaning the exterior of the radio.
7. Do not place the radio on an unstable cart, stand, bracket or table.
The radio may fall, causing serious personal injury and damage to
the radio.
8. Ventilation: This radio should be situated so that its location or
position does not interfere with its proper ventilation. For example,
the radio should not be used on a bed, sofa, rug or other soft
surfaces that may block the ventilation openings. It should not be
place in a built-in situation like a cabinet that may reduce air flow
through the ventilation openings.
9. Power sources: The radio should be operated only from the type of
power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your radio dealer or
power company.
10. Mains adaptor: The mains adaptor should be positioned so it is not
walked on, pinched, or items placed on top of it. Pay particular
attention to wires at plugs, convenience receptacles, and the point
where they exit from the unit. Unplug the mains adaptor by gripping
the adaptor, not the wire. Operate the radio using only the current
type of power source indicated. If you are not sure of the type of
power supply to your home, consult your dealer or local
power company.
11. Do not overload wall outlets or extension cords. This can result in a
risk of fire or electric shock. Never insert objects of any kind into
the radio through opening. The objects may touch dangerous
voltage points or short out parts. This could cause a fire or
electric shock.
12. If the radio is left unattended or unused for long periods of time,
unplug it from the wall outlet. This will prevent damage caused by
lightning or power line surges.
13. If the radio is left unattended or unused for long periods of time,
remove the batteries. The batteries may leak and damage furniture
or your radio.
2
14. Do not attempt to service the radio yourself. Removing the cover
may expose you to dangerous voltage, and will void the warranty.
Refer all servicing to authorized service personnel.
15. Object and Liquid Entry-Never push objects of any kind into this
radio through opening as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind of product.
16. The appliance should be serviced by qualified personnel when:
A. The mains adaptor or the plug has been damaged.
B. Objects have fallen or liquid had been spilled into the radio.
C. The radio has been exposed to rain or water.
D. The radio does not appear to operate normally or exhibits a
marked change in performance.
E. The radio has been dropped, or the enclosure damaged.
3
Introduction
GB
The Sangean DCR-200 DAB/FM RDS Digital Receiver provides the
following range of features in an stream-lined portable size:
Radio for DAB and FM (with RDS) broadcasts.
20 radio station presets (10 for DAB and 10 for FM) and 8 my favorite
stations (4 for DAB and 4 for FM).
DC output socket for charging mobile phones, MP3 players or
CD players.
Built-in wire spring aerial and external FM/DAB wire spring aerial for
radio reception.
Clock display with time when in standby.
Two alarm timers with snooze feature to wake you to either buzzer,
radio alarm, voice messages.
Adjustable sleep timer which can be set to turn the digital receiver off
after between 15 and 120 minutes.
2 voice message recording function with each 10 seconds duration.
A 3.5mm stereo Auxiliary Input socket for playing audio from MP3
players, iPod devices or other audio equipment.
A standard 3.5mm headphone socket for private listening.
Attractive, large and ergonomically designed knobs.
Desirable and functional flat membrane push button.
4
Controls and connections
1.
2.
3.
4.
5.
6.
5
Sleep timer
Backlight
Alarm / Menu
Standby
Band
Auto Tune
7.
8.
9.
10.
11.
12.
Preset station 1 – 4
Timer
Message button
Message button
Advanced setting / Info button
Memory preset
Controls and connections
GB
13. Microphone
14. LCD display
15. Tuning / Select knob
16. Volume knob
6
Controls and connections
17. Battery compartment
18. Headphone socket
19. DC in jack
7
20. Aux in socket
21. DC out jack
22. Antenna socket
Controls and connections
GB
23. Buzzer volume adjuster
24. USB socket for software upgrade
8
Display icons
A. Battery capacity indicator
B. Alarm 1 icon
C. Alarm 2 icon
D. DAB icon
E. FM icon
F. Timer icon
G. Sleep timer / snooze indicator
H. Signal strength indicator
I. Time / Radio display screen
9
Using the digital receiver for the first time
GB
1. Place your digital receiver on a flat surface.
2. Insert the adaptor plug into the DC in socket located on the back
of your digital receiver ensuring that the plug is pushed fully into
the socket.
3. Plug the other end of the adaptor into the wall socket.
IMPORTANT:
The mains adaptor is used as the means of connecting the digital
receiver to the mains supply. The mains socket used for the digital
receiver must remain accessible during normal use. In order to
disconnect the digital receiver from the mains completely, the adaptor
should be removed from the mains socket outlet completely.
4. When your digital receiver is first switched on the clock display will
show SANGEAN briefly first and then NO CLOCK, and the unit will
enter standby mode. It will then scan for DAB radio stations and when
stations have been found the clock time should be set automatically.
Note that the display will not show any scanning message for this
first scan.
5. If no stations have been found then the clock will not set.
You may need to relocate your digital receiver to a position giving
better reception. You should then carry out an auto-tune to find
DAB stations.
10
Operating your digital receiver – DAB
1. Press the Standby button to switch on the digital receiver.
If the digital receiver has been used before the last used mode
will be selected.
1
2. Press and release the Band button as needed so that DAB mode is
selected on the display.
3. If this is the first time the digital receiver is used a full scan of the
DAB channels in your country will be carried out. The display will
show “Tuning” for a few seconds. (If the digital receiver has been
used before the last used station will be selected).
4. The first station in the list of stations found during the scanning
process will be played. The display will show the station name.
5. If no signals are found, the digital receiver will show “OFF AIR” and it
may be necessary to relocate your digital receiver to a position giving
better reception, and then repeat the scan following above procedure.
11
2
GB
Selecting a DAB radio station
1. Press the Standby button to switch on your digital receiver.
The display will show “TUNING” for a few seconds.
2. Press the Band button to select DAB radio mode. The display
normally shows the name of the current station selected.
3. Rotate the Tuning control to access the radio station list and to scroll
through the list of available stations. Stop rotating the Tuning control
when you find the station that you wish to hear.
2
4. Press and release the Tuning control to cause the digital receiver to
tune to the chosen station. The display may show “TUNING” while
your digital receiver finds the new station.
5. Adjust the Volume control to set the sound level as needed.
Secondary services
1. Certain radio stations have one or more secondary services
associated with them. If a station has a secondary service associated
with it then the secondary service will then appear immediately after
the primary service as you rotate the Tuning control.
3,4
5
2. Most secondary services do not broadcast continually and if the
selected service is not available, the radio will re-tune to the
associated primary service.
12
Display modes – DAB
Your digital receiver has a range of display options when in DAB mode:
1. Repeatedly press and release the Info button to cycle through the
different options.
a. Station Name
Displays the name of the station being
listened to.
b. Scrolling Text
Displays scrolling text messages such as
the artist or track name, phone in number,
website address, etc.
c. Program Type
Displays the type of station being listened
to such as Pop, Classic, News, etc.
d. Multiplex Name
Displays the name of the DAB multiplex to
which the current station belongs.
13
GB
e. Time
Displays the current time.
f. Date
Displays the current date.
g. Frequency & Channel Displays the frequency and channel number
for the current DAB radio station.
h. Bit Rate
Displays the digital bit rate for the station
being listened to.
i. Signal Error
Displays the bit error rate for the station being
listened to.
The display will revert to a conventional time display 10 seconds after
the last button pressed except when displaying scrolling text.
A signal strength indicator is always shown in the display on the upper
right corner.
If the currently tuned station has been stored as a preset, then the
preset number will also be shown.
14
Finding new stations – DAB
Should you wish to use your digital receiver for DAB reception in a
new location, or if no station were detected during the initial scan,
you can follow this procedure to allow your digital receiver to find out
which DAB radio stations are available.
1. With the unit in DAB mode press and release the Auto-tune button.
The digital receiver will carry out a full scan of the entire DAB
frequencies in your country.
2. As stations are found the station counter on the right-hand side of the
display will show the total numbers of DAB stations in your area,
and the stations will be added to the list.
15
Manual Tuning - DAB
GB
Manual tuning allows you to tune directly to the various DAB Band III
channels. DAB Band III channels are located in the range 5A to 13F.
1. Press and hold the Info button to enter Advanced Information so that
the display shows “MANUAL”.
2. Press and release the Tuning control to enter the Manual menu.
3. Rotate the Tuning control to select the required DAB channel.
4. Press and release the Tuning control to select the channel. If a signal
is present, this will be indicated on a signal strength display.
The minimum signal marker (0) shows the minimum signal strength
needed for good DAB reception. The signal indicator chevrons go up
or down showing the changing signal strength as you adjust the wire
aerial or your digital receiver.
2-4,6
5. Any new stations that are found are automatically added to the
stored list of stations.
6. Press and release the Tuning control to return to normal tuning mode.
16
Dynamic Range Control (DRC) settings – DAB
Dynamic Range Control (also knows as DRC) can make quieter sounds
easier to hear when your radio is used in a noisy environment.
This function is only for the DAB waveband.
1. Press the Standby button to switch on your digital receiver.
2. Press the Band button as needed to select the DAB radio mode.
2
3. Press and hold the Info button to enter the Advanced Information
menu so that “MANUAL” appears on the display.
4. Rotate the Tuning control until the display shows “DRC VAL”.
5. Press and release the Tuning control to enter the DRC
adjustment mode.
6. Rotate the Tuning knob to select the required DRC setting
(the default is 0).
DRC 0 DRC is switched off, Broadcast DRC will be ignored.
DRC 1/2 DRC level is set to 1/2 that sent by broadcaster.
DRC 1 DRC is set as sent by broadcaster.
7. Press and release the Tuning control to confirm the setting.
The display will then return to the previous radio display mode.
Note:
Not all DAB broadcasts are able to use the DRC function.
If the broadcast does not support DRC, then the DRC setting in the radio
will have no effect.
17
3
4-7
Operating your digital receiver – Search tuning FM
GB
1. Press the Standby button to switch on your digital receiver.
2. Press the Band button as needed until the FM band is selected.
1
3. Press and release the Auto-tune button to carry out an auto-tune.
Your digital receiver will scan up the FM band from the currently
displayed frequency and will stop scanning automatically when it
finds a station of sufficient strength. To scan down the FM band,
press and hold the Auto-tune button.
2
4. The display will show the frequency of the signal found. If the signal
is strong enough and there is RDS information available, soon after
the display will show the radio station name.
5. To find more FM stations press and release the Auto-tune button to
repeat the scan operation as DAB stations before.
3,5
6. When the end of the waveband is reached your digital receiver will
recommence tuning from the opposite end of the waveband.
7. Use the Volume control to adjust the sound level as required.
7
18
Manual tuning – FM
1. Press the Standby button to switch on your digital receiver.
2. Press and release the Band button to select FM radio mode.
1
3. Rotate the Tuning control to tune to a station. The frequency will
change in steps of 50kHz.
4. When the end of the end of the waveband is reached your digital
receiver will recommence tuning from the opposite end of
the waveband.
2
5. Use the Volume control to adjust the sound level as required.
3
5
19
Display modes – FM
GB
Your digital receiver has a range of display options for FM radio mode.
1. Repeatedly press and release the Info button to cycle through the
different options.
a. Frequency
Displays the frequency of the FM signal.
b. Station name
Displays the name of the station being listened to.
c. Program type
Displays the type of station being listened to such
as Pop, Classic, News, etc.
d. Scrolling text
Displays text messages such as new items etc.
e. Time
Displays the current time.
f. Date
Displays the current date.
Note:
If no RDS information is available, then the digital receiver will only be
able to display the frequency. There will be no text or program type
information available under these conditions.
The digital receiver only provides displays when there is
information available. So if there is no text, for example, that display is
not available.
20
FM stereo / mono
If the FM radio station being listened to has a weak signal some hiss
may be audible. It is possible to reduce this hiss by forcing the radio to
play the station in mono rather than stereo.
1. Press the Band button as needed to select the FM radio mode
display and tune to the required FM station as previously described.
2. Press and release the Tuning control and if the display will show the
current setting. If the setting is Auto press the Tuning control to
switch to Mono mode to reduce the hiss.
3. To return to Auto (stereo) mode press and release the Tuning
control again, so that the digital receiver will switch back to
Auto mode.
21
2,3
Presetting stations in DAB and FM modes
GB
There are 10 memory presets each for DAB and FM radio. Apart from
the 10 presets, there are 4 my favorite stations. They are used in the
same way for each waveband.
1. Press the Standby button to switch on your digital receiver.
2. Press the Band button to select the desired waveband. Tune to the
required radio station as previously described.
3. Press and hold down the required favorite station number (1 to 4) until
the display shows “ 1 saved”. The station will be stored using the
chosen number. Repeat this procedure for the remaining favorite
stations as you wish.
4. To store the station in the 10 memory presets, press and hold the
Memory button to enter the memory preset menu.
2
3
5. Rotate the Tuning control to select the required preset
station number. Press and release the Tuning control until the display
shows “06 SAVED”.
6. Preset memories which have already been stored may be overwritten
by following the above procedure if required.
4
5
22
Recalling a preset in DAB and FM modes
1. Press the Standby button to switch on your digital receiver.
2. Select the required waveband by pressing the Band button.
3. To tune to one of the 4 my favorite stations stored in my
favorite stations, press and release the my favorite station button.
4. Momentarily press the required main Preset button to cause
your digital receiver to tune to one of the stations stored in the
10 main presets.
5. Rotate the Tuning control to scroll through the preset station list,
and then press and release the Tuning control to select the desired
preset station. Your digital receiver will tune to the chosen preset
station stored in the preset memory.
2
3
4
5
23
Clock and Alarms
GB
Automatically updating the clock
Your digital receiver will normally update the clock automatically when
tuning to the radio broadcast. After a power failure the digital receiver
will then set its clock the next time that you turn on the digital receiver
in DAB or FM mode.
When the digital receiver is in Standby mode, the clock will be
automatically synchronized with DAB radio.
Setting the time format
The clock display used in stand-by mode and on the playing mode
screens can be set to 12 or 24 hour format. The selected format is then
also used when setting the alarms.
1. With your digital receiver switched on, press and hold down the
Menu button until the display shows “ALARM 1” flashing.
2,3
2. Rotate the Tuning control until “TIME FMT” shows on the display.
Press the Tuning control to enter the system settings menu.
3. Rotate the Tuning control to select either 12 or 24 hour format.
Press and release the Tuning control to confirm your choice of
clock format. The display will then revert to the previous menu.
If the 12 hour clock format is chosen, the digital receiver will then use
the 12 hour clock for the setting of alarms, and will display a 12 hour
clock for the setting of alarms, and will display a 12 hour clock with an
AM or PM indicator when in stand-by mode.
24
Setting the date format
1. With your digital receiver switched on, press and hold down the
Menu button to access the menu setting.
2. Rotate the Tuning control until “DATE FMT” shows on the display.
Press and release the Tuning control to enter the date format setting.
3. Rotate the Tuning control to select the required date format.
Press and release the Tuning control to confirm your choice of date
format. The display will then revert to the previous menu.
2,3
25
Setting the alarm clock
GB
Your DCR-200 digital receiver has two alarms which can each be set to
wake you to DAB, FM radio, voice message or buzzer alarm.
The alarms may be set while the unit is in standby mode or
while playing. The alarm clock setting will not function when the display
appears NO CLOCK.
1. Before setting an alarm ensure that the clock time is set. Press and
hold the Alarm button. “Alarm 1” will show on the display.
2. Rotate the Tuning control to select the required alarm, 1 or 2.
Press and release the Tuning control to enter the alarm setting.
3. Rotate the Tuning control to choose whether to set the alarm to On
or Off. If you decide to abort alarm setting, choose Back and press
the Tuning control.
2-7
4. Press and release the Tuning control. If the previous selection was to
switch on the alarm, then alarm time setting will show on the display
and the Alarm hour digits will flash. If Off was selected, the unit will
exit the alarm menu.
5. Rotate the Tuning control to choose the alarm hour and then press
and release the Tuning control to enter the hour setting. The alarm
minute digits will then flash on the display.
6. Rotate the Tuning control to choose the alarm minute and then press
and release the Tuning control to enter the minute setting.
26
7. Rotate the Tuning control to choose the required alarm mode,
and then press and release the Tuning control to confirm the setting.
The alarm can be set to buzzer, DAB radio, FM radio,
or voice message. When radio mode is selected, the radio alarm is
set to the station most recently listened to.
27
GB
8. Rotate the Tuning control to select the required alarm frequency
option when radio mode is selected. The display will show the
frequency options for the alarm. The alarm options are as follows:
OFF – the alarm will be disabled
ONCE – the alarm will sound once
DAILY – the alarm will sound everyday
WEEKDAYS – the alarm will sound on weekdays only
WEEKENDS – the alarm will sound only at weekends
Press the Tuning control to confirm the setting.
10
10
9. The alarm has now been set. “SAVED” will show on the display,
and then will revert to previous mode.
10. Rotate the Volume control to set the required volume. Adjust the
switch inside the battery compartment to set the required volume
level for buzzer alarm. When the digital receiver is set to wake
by DAB, FM radio, or voice message, the alarm volume will be the
volume previously listened to.
To view an alarm setting press and release the Alarm button and the
display will show “Alarm 1”. Press and release the Tuning control to
enter the Alarm 1 setting, and repeatedly press and release the Tuning
control to view through the alarm details.
Active alarms are shown using small alarm indicator at the top of the
playing displays and on the clock display when in stand-by.
28
When the alarm sounds
The alarm icon will flash at the display when an alarm is sounding.
To cancel an alarm, press the Standby button to return to
Stand-by mode.
When the buzzer alarm activates, the alarm will start softly and
gradually increase in level. It will sound for 1 minute and silence for
1 minute at the selected time in repetition for up to 30 minutes unless
cancelled. The digital receiver will sound at the selected time for up to
60 minutes for other alarm types.
Disabling alarms
1. To disable a single alarm enter the alarm setup menu and rotate the
Tuning control until the desire alarm is showed on the display.
Press the Tuning control.
2. Rotate the Tuning control until “OFF” is showed on the display,
and press and release the Tuning control.
3. The display will return to previous mode and the chosen alarm will
now be disabled.
Note: To cancel a sounding alarm, simply press the Standby button.
29
1,2
Snooze
GB
1. When the alarm sounds, press any button other than the Standby
button will silence the alarm for five minutes. The snooze symbol
will appear in the display.
2. To cancel the snooze timer while the alarm is suspended, press the
Standby button.
Sleep timer
Your digital receiver can be set to turn off after a preset time has
elapsed. The sleep timer setting can be adjusted between
15, 30, 60, 90 and 120 minutes.
1. To use the sleep timer, press and release the Sleep timer button to
enter the sleep timer setting. “Sleep 15” will appear on the display.
2. Rotate the Tuning control to select the desired sleep time.
Your digital receiver will switch off after the preset sleep time
has finished.
An active sleep timer is shown using a small sleep timer / snooze
indicator at the top of the playing displays.
2
3. Use the OFF option to cancel the sleep function. To cancel the sleep
function before the preset time has elapsed, either to set the sleep
time to off or press the Standby button to turn the unit off manually.
30
Egg timer function
1. Press and release the Egg timer button to enter timer setting and
rotate the Tuning control to adjust the minute setting during 1 and
120 minutes with 1 minute interval.
2. Press and release the Tuning control to finish the setting and the egg
timer will start to countdown, meanwhile the display will show the
remaining minutes. The countdown display will become normal
display after 10 seconds.
3. Press and release the Egg timer button to view the remaining time
for an active timer setting. To cancel the function when countdown
is progressing, press and hold the Egg timer button until the Egg
timer indicator disappears.
4. Rotate the Tuning control while the display shows the remaining time
of countdown to adjust the required timer setting again.
Note:
the digital receiver will sound for 3 minutes when an active timer finishes
its countdown.
31
2,3
Display and Audio
GB
Brightness control
The brightness of the display when the unit is in standby mode may
be adjusted. If you use the unit in the bedroom, you may prefer a lower
standby brightness level than the standard setting.
1. Press the Backlight button so that the display shows for example
“LIGHT 4”.
2. Press the Backlight button one more time to change the standby
brightness level. The backlight level will change at the same time
so that you can see the effect of the change.
The default setting after a system reset is 3. Possible brightness values
range from 1 – 7.
2
32
Moon LED
When using the digital receiver, you can turn on the moonlight LED at
the bottom of the receiver for your better listening experience.
1. Press and hold the Menu button to enter the menu setting.
2. Rotate the Tuning control until the display show “MOON LED”.
Press and release the Tuning control to enter the setting.
1
3. Rotate the Tuning control to select ON or OFF. Press and release the
Tuning control again to confirm the setting.
2,3
33
Message function
GB
The message function can record and playback with 2 sets of voice
message for 10 seconds each.
1. Press and hold the Message button to record the voice up to
10 seconds length. The LED is lighted during recording and the
display will show RECORD. Press and release the Message button
to pause the recording. After recording the LED will be flashing.
1-3
2. Press and release the Message button to playback the voice content,
and the display will show PLAYING. Press the message button to
pause the message while it is being playback, and the LED will dim.
3. To overwrite an existing message, press and hold the Message
button for 2 seconds to start recording a new message.
4. This Message button can operate in power on or off mode. In power
on mode the receiver even in DAB or FM as well as Aux-in will mute
during the voice message processing.
Note:
The Message button LED will be lighted during recording and
playing messages.
34
Key tone adjustment
The sound of pressing the buttons of the receiver can be
adjusted manually.
1. Press and hold the Menu button to enter the menu setting.
2. Rotate the Tuning control until the display shows “KEY TONE”.
Press and release the Tuning control and select ON or OFF to
activate or deactivate the key tone sound.
Note:
Setting of the buzzer volume adjuster on the rear of the unit may
effect the key tone volume
Headphone socket
A 3.5mm stereo Headphone Socket is provided on the rear of your
digital receiver for use with headphones. Inserting a plug automatically
mutes the internal loudspeaker.
IMPORTANT:
Excessive sound pressure from earphones and headphones can cause
hearing loss.
35
2
Auxiliary input socket
GB
A 3.5mm stereo Auxiliary Input socket is provided on the rear of your
digital receiver to permit an audio signal to be fed into the unit from an
external audio device such as iPod, MP3 or CD player.
1. Repeatedly press and release the Band button until “AUX IN”
is displayed.
2. Connect an external audio source (for example, iPod, MP3 or
CD player) to the Auxiliary Input socket.
1
3. Adjust the volume setting on your iPod, MP3 or CD player to ensure
an adequate signal level from the player, and then use the Volume
control on the digital receiver as needed for comfortable listening.
DC out jack
A 4.4mm 5V / 0.8A DC output jack is provided along with the digital
receiver for you to connect and charge any compatible external device.
This function can only work in DC mode, and is not workable when using
the batteries.
36
Information
System reset
If your radio fails to operate correctly, or some digits on the display are
missing or incomplete carry out the following procedure.
1. Press and hold the Info button when the radio is in DAB or FM mode
to enter Advanced Information.
2. Rotate the Tuning button until the display shows “FACTORY”.
Press and release the Tuning control so that the display
shows “RESET”.
3. Press and release the Tuning control again to confirm the
reset operation. A full reset will be performed. The station list and
presets will be set to empty. Alarms will be cancelled and Egg timer
and sleep timer settings will be set to their default values.
The display will show “NO CLOCK” and after a few seconds a station
scan search will be performed automatically.
37
1
2,3
Software version display
GB
1. Press and hold the Info button when the radio is in DAB or FM mode
to enter the Advanced Information.
2. Rotate the Tuning control until the display shows “SW VER”.
Press the Tuning control again to show your digital receiver’s
software information.
3. After a few seconds your digital receiver will return to the normal radio
display mode.
1
2
USB socket for software upgrade
Software updates for your radio may be available in the future.
As software updates become available software and information on
how to update your radio can be found at
http://sg.sangean.com.tw/first/first.asp
http://www.sangean.eu/first/first.asp
www.sangean.com.au.
For more information, please contact our Head Office by sending an
email to info@sangean.com.
38
Specifications
Circuit Features
Power Requirements
Mains
DC in 7.5V / 1.6A
DC out 5V / 0.8A
Loudspeaker
2.5”
Output Power
Headphone socket
Auxiliary socket
1 Watt
3.5mm dia
3.5mm dia
Aerial System
FM Wire aerial
DAB Wire aerial
Frequency Range
FM: 87.5 – 108 MHz
Channel Block
DAB (BAND III) 5A – 13F
Battery
4 X 1.5V Size “C” / UM-2 / R14
If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not
be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice. (Waste Electrical and Electronic Equipment Directive)
39
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising