– LF05CA2 LINEARlight Colormix Flex www.osram.com/LED-systems.com Technical Datasheet

– LF05CA2 LINEARlight Colormix Flex www.osram.com/LED-systems.com Technical Datasheet
www.osram.com/LED-systems.com
LINEARlight Colormix Flex – LF05CA2
Technical Datasheet
Benefits
Flexible, cuttable & self-adhesive RGB module
Optimum color mixing:
 each LED contains red, green and blue emitters
 All emitters centered on the board
Developed for colourful ambient, mood and decorative lighting.
Applications
Light boxes / back lighting
Edge-coupling of transparent or diffuse materials
Path illumination, contour accentuation
Ambient, mood and decorative lighting
8
100
4,000
20
2.2
all dimensions in mm
Quick reference
Product
Order Code
Color
LF05CA2-RGB3
4008321851536
RGB
Dominant
Wavelength
Red
625
Green
Blue
525
465
W/m
lm/m
lm/W
Shipping Units
18
470
26
1/8
7.2
5.4
4.8
161
256
53
22
47
11
Technical features
Dimming / Color control
Pulse width modulation (PWM)
RGB
Each LED with 3 separate emitters for RED, GREEN, BLUE
All emitters centered on the board
Lifetime
50,000 h (L70B50 @ Tc = 40°C)
Adhesive tape on backside
3M VHB 9460
Cut & Connect
Cuttable every 10 cm / Easy connect with SLIMCONNECTsystem
Complementary systems
SLIMCONNECTsystem, SLIM TRACK, OPTOTRONIC
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Subject to change without notice. Errors and omissions excepted. Version: 2013-07-09
LINEARlight Colormix Flex® – LF05CA2
1/4
www.osram.com/LED-systems.com
Technical operating data (for overall module)
Product
Order Code
LF05CA2-RGB3
4008321851536
Color
RGB
Red
Green
Blue
Voltage
[V]
24
24
24
24
Power
[W]
72
28.8
22
19.2
Current
[A]
3
1.2
0.9
0.8
Luminous
Flux [lm]
1883
645
1025
213
Radiance
Angle [°]
120
Overall
Length
4m
Minimum & maximum ratings
LF05CA2
Operating temperature at
Tc-Point [°C]
-30 … +75°C
Storage temperature
[°C]
-40 … +85°C
Voltage range
[V dc]
23 … 25 V
Reverse Voltage
[V dc]
25 V
► Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the LED Module.
► Exceeding maximum ratings for operating voltage will cause hazardous overload and will likely destroy the LED Module.
► The temperature of the LED module must be measured at the Tc-point according to EN60598-1 in a thermally constant status with a
temperature sensor or a temperature sensitive label. For exact location of the Tc-point see drawing below.
Technical drawing
Safety information
► The module has to be protected from mechanical loads
► Assembly must not damage or destroy conducting paths on the circuit board.
► Installation of LED modules (with power supplies) needs to be made with regard to all applicable and safety standards. Only qualified
personnel should be allowed to perform installations.
► Observe correct polarity!
Depending on the product incorrect polarity will lead to emission of no light. The module can be damaged after a few seconds. To prevent
this, correct polarity immediately! (see "reverse voltage", page 2)
► Parallel connection is highly recommended as safe electrical operation mode.
Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload the LED module.
► ESD protection methods have to be observed when cutting and connecting the module. Check on ESD handling in the application note
ESD protection for LED modules.
► The LED Module must not be operated under water
► Please ensure that the power supply is of adequate power to operate the total load.
► When mounting on metallic or otherwise conductive surfaces, there needs to be an electrical isolation at soldering points between module
and the mounting surface.
► The maximum run length from any power feed should be limited to 4000 mm.
► Damage by corrosion will not be honored as a materials defect claim. It is the user´s responsibility to provide suitable protection against
corrosive agents such as moisture and condensation and other harmful elements.
► For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable protection
class. The module can be protected against condensation water by treatment with an appropriate circuit board grade conformal coating.
The conformal coating should have the following features:
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Subject to change without notice. Errors and omissions excepted. Version: 2013-07-09
LINEARlight Colormix Flex® – LF05CA2
2/4
www.osram.com/LED-systems.com
-
Optical transparency
-
UV-resistance
-
Thermal expansion coefficient 15 – 30 * 10-6 K-1
-
low permeability of steam for all climatic conditions
-
resistance against corrosive environment
► Dimming/ color controlling is only possible with PWM.
► The LINEARlight Colormix Flex is driven ideally by OSRAM OPTORONIC power supplies and control gear. Control gear is available with
1..10V, DALI or DMX interface.
► Please refer to the maximum currents of the control gear when calculating the whole installation (OT DIM: 5A, OTi DALI DIM: 5A, OT
DMX, 3-Channel DIM or Sequencer: 2A per channel). Please read our OPTOTRONIC technical installation guide for more detailed
information about calculation and wiring diagrams.
In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically stabilized power
supply protecting against short circuits, overload and overheating.
To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC
certified. In Europe the declarations of conformity must include the following standards:
CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384.
Also check for the mark of an independent authorized certification institute.
Please see the relevant brochure for more detailed information (see "Related and Further Information")
OSRAM OPTOTRONIC® control gear complies to all relevant standards and guarantees safe operation.
Assembly Information
► The module can be connected easily and without any tools with the optional SLIMCONNECTsystem.
Please note the maximum ampacity.
► Connection with soldering wires on unmounted module:
Do not pretin the solderpads (marked "24V +/RGB")but pretin the wires and solder for max 4 s at 300 °C. Allow solderpoints to completely
cool down before the next soldering. Prevent shear- or peel forces.
► Soldering of wires with the module mounted on a heatsink:
Pretin solderpads and wires and solder for max 3 s at 350 °C. Allow solderpoints to completely cool down before the next soldering.
Prevent shear- or peel forces.
► The mounting of the module is facilitated by means of the double-sided adhesive on the back-surface of the module. Care must be taken
to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particle. The mounting substrate must have
sufficient structural integrity. Take care to completely remove the protective film. Once the module is appropriately positioned, press on the
module with about 20N/cm² (refer to application techniques of 3M adhesive transfer tapes).
► The minimum bending radius is 20 mm.
► When installing in environments with large variations in temperature (e.g. outdoor applications) and operating length of more than 2 m, the
use of metallic mounting surfaces is necessary. Otherwise it is advisable to use an additional thicker adhesive tape to absorb the stress of
any mismatch in expansion coefficients.
► We do not recommend the use of LINEARlight Colormix Flex® in applications where only white light is needed. For those, rather use
LINEARlight POWER Flex®, LINEARlight Flex® ADVANCED & LINEARlight Flex® Eco.
Complementary systems and accessories
Accessories
Type
SLIMMCONNECTsystem
4pin Feeder
Jumper (board-to-board)
Extension wire 30mm
Extension wire 150mm
SLIM TRACK System
SLIM TRACK
Mounting Bracket for SLIM TRACK
Clear SLIM TRACK Cover
Diffuse SLIM TRACK Cover
Endcap for Diffuse Cover
Semi-Diffuse SLIM TRACK Cover
Product
EAN
Shipping units
LF-4PIN Flex SC
LF-CONN Flex SC
LF-WIRE-30 FLEX SC
LF-WIRE-150 FLEX SC
4052899904835
4008321832467
4008321875587
4008321875563
10 / 250
25 / 250
100 / 10,000
50 / 5,000
LF-LTS-2100 SLIM TRACK
LF-LTS-MB
LF-LTS COVER C
LF-LTS-COVER-DIFFUSE
LF-LTS-ENDCAP
LF-LTS COVER S
4008321978981
4008321979025
4008321790187
4008321979001
4008321979049
4008321790200
40
35 / 280
40
40
20 / 160
40
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Subject to change without notice. Errors and omissions excepted. Version: 2013-07-09
LINEARlight Colormix Flex® – LF05CA2
3/4
www.osram.com/LED-systems.com
OPTOTRONIC
► Please consider that lengths may differ if further controls are installed.
Recommended OPTOTRONIC® drivers
Non-dimmable
EAN
Recommended max. length per driver
OPTOTRONIC OT 6/200-240/24 CE
OPTOTRONIC OT 8/200-240/24
OPTOTRONIC OT 20/220-240/24
OPTOTRONIC OT 20/120-240/24 S
OPTOTRONIC OT 75/220-240/24
OPTOTRONIC OT 75/220-240/24 E
OPTOTRONIC OT 80/220-240/24 P
OPTOTRONIC OT 120/220-240/24 P
OPTOTRONIC OT 240/220-240/24 P
Dimmable
OPTOTRONIC OT EASY 60 II
OPTOTRONIC OT EASY 80 [RECOMMENDATION]
4008321113269
4008321040169
4050300618111
4050300662626
4050300817477
4008321362476
4008321981684
4008321981707
4008321981721
0,1 m ⁽*⁾ - 0,3 m
0 m - 0,4 m
0,1 m ⁽*⁾ - 1,1 m
0,1 m ⁽*⁾ - 1,1 m
0 m - 4,1 m ⁽**⁾
0 m - 4,1 m ⁽**⁾
1,4 m ⁽*⁾ - 4,4 m ⁽**⁾
3,4 m ⁽*⁾ - 6,6 m ⁽**⁾
6,7 m ⁽*⁾ ⁽**⁾ - 13,3 m ⁽**⁾
4008321187796
4008321808363
0 m - 3,3 m
0 m - 4,4 m ⁽**⁾
OPTOTRONIC OT 65/220-240/24 3DIM E
OPTOTRONIC OTi DALI 75/220-240/24 1-4 CH
OPTOTRONIC OT 80/220-240/24 DIM P
OPTOTRONIC OT 120/220-240/24 DIM P
OPTOTRONIC OT 240/220-240/24 DIM P
4008321964403
4008321371560
4008321981677
4008321981691
4008321981714
0 m - 3,6 m
0 m - 4,1 m ⁽**⁾
1,4 m ⁽*⁾ - 4,4 m ⁽**⁾
3,4 m ⁽*⁾ - 6,6 m ⁽**⁾
6,7 m ⁽*⁾ ⁽**⁾ - 13,3 m ⁽**⁾
⁽*⁾ Operation with shorter length possible. Recommended minimum length to achieve optimum operating conditions.
⁽**⁾ Total lengths per driver. Length of single strip must not exceed 4 m.
Maximim length per OT:
lA + lB + lC + …  lmax/OT
lA
Maximum length per strip:
lB
lA
lB
lC
l…
OT – 24V
lC
≤
≤
≤
≤
4m
4m
4m
4m
Contacts & information
German engineering meets Italian elegance – creating a European product
All LINEARlight Colormix Flex® are Made in Italy by OSRAM, with over 100 years of experience in light solutions.
OSRAM GmbH
Hellabrunner Str. 1
81536 Munich, Germany
www.osram.com
+49.89.6213-0 (Headquarter)
+49.89.6213-6000 (Customer-Service-Center)
Sales and technical support is given by the local OSRAM
subsidiaries.
On the OSRAM website all subsidiaries are listed with
complete address and phone numbers.
OSRAM LED Systems
OSRAM catalogue
General information
www.osram.com/led-systems
http://catalog.osram.com
www.osram.com
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Subject to change without notice. Errors and omissions excepted. Version: 2013-07-09
LINEARlight Colormix Flex® – LF05CA2
4/4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement