INSTALLATION INSTRUCTIONS
INSTALLATION
INSTRUCTIONS
0-35% MOTORIZED FRESH AIR DAMPER
# 547840
FOR USE ON PACKAGE EQUIPMENT MODELS
R6G(D,F,I) / R8GD / P6SD / Q6SD 024-060
FORM# 598A-0512 (REPLACES 598A-0709)
The 0-35% outside air damper system is designed to fit over the opening in the horizontal return air panel by replacing the
unit horizontal return air duct cover. Slight field modification to the unit is required. The amount of outside air allowed into
the occupied space is easily controlled by adjusting the two slide dampers included with the kit. The 2 position motor
closes upon loss of 24VAC power when unit is not in heating or cooling mode thus eliminating unwanted drafts into the
airstream. The panel is fully insulated.
Step 1:
Check for correct number of parts. See list below:
1 ea. - Outside Air Intake panel assembly with hood,
damper motor, and slide dampers.
Step 2:
Warning:
Recognize this symbol as an indication of
Important Safety Information!
Read all instructions prior to installation.
Remove the return air duct cover from unit and retain the
screws for later use.
Disconnect electrical power to the unit
before servicing.
Step 3:
Failure to do so can cause electrical shock
resulting in personal injury or death.
Remove the return air panel from the unit. Locate unit
accessory plug at top of return air compartment and connect to
fresh air accessory low voltage plug per diagram on back of
this instruction sheet.
Note: On shorter models it may be possible to snap lock
the two connecting plugs without removal of the return air
panel by reaching up through the horizontal return air
opening.
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. Refer to this manual. For
assistance or additional information consult
a qualified installer or service agency.
DO NOT DESTROY. PLEASE READ CAREFULLY AND
Step 4:
Using a pair of 3”-4” flat sheet metal crimping pliers carefully
form the 90 Deg. mounting flanges outward along the
perforated lines around the full perimeter of the horizontal
return air opening.
A/C UNIT
Step 5:
Install outside air intake hood assembly as shown in Figure 1
over duct opening and attach with screws removed in Step 2.
Screws should attach to formed flanges to avoid possible
damage to internal components of the unit.
Step 6:
Adjust slide dampers to the desired position allowing the
correct amount of fresh air into the return airstream to meet
requirements of the building. CFM and percentage of fresh air
can be determined through the following guidelines with the
use of basic equipment. Temperature measurements for the
outdoor fresh air and indoor return air are required to calculate
the resultant supply air temperature while only the indoor
blower is operating. No mechanical cooling should be
operating while adjusting the damper blades position.
RETURN ACCESS PANEL
ADJUSTABLE SLIDE DAMPERS
OUTSIDE AIR ASSEMBLY
FILTER INSTALLED IN THE HOOD
2 POSITION MOTOR
FIGURE 1
INSTALLATION
INSTRUCTIONS
0-35% MOTORIZED FRESH AIR DAMPER
# 547840
FOR USE ON PACKAGE EQUIPMENT MODELS
R6G(D,F,I) / R8GD / P6SD / Q6SD 024-060
Fresh Air Damper Position Adjustment
Slide damper position for ventilation of building contaminants and people occupancy can be adjusted to the proper CFM
requirements using the following guidelines. Consult your State or local codes as required.
1. Disconnect main power to the unit.
2. Set the thermostat Fan switch to “ON” or place a jumper across “R” and “G” at the unit low voltage terminal strip.
3. Restore power to the unit. Blower should energize and run continuously while the motorized damper moves to the
open position.
Calculate the appropriate mixed air temperature per the following equation:
* (Return Air Temp. x % of Return Air) + (Outside Air Temp. x % of Outside Air) = Mixed Air Temperature
Example:
Assume local code requires 10% outdoor air during occupied conditions, (200 CFM of total unit CFM = 2,000) outdoor air is
50 Deg. F, and return air is 75 Deg. F.
Under these conditions, what is the mixed air temperature in the supply duct?
* (50 Deg. F x 0.1) + (75 Deg. F x 0.9) = 5.0 Deg. F + 67.5 Deg. F = 72.5 Deg. F
Adjust the slide damper position until the mixed supply air temperature reaches the calculated value.
Note: It will be necessary to remove the intake hood so the second slide damper can be removed, if the full
amount of outside air is required.
4. Once damper adjustments are completed, turn off power to the outdoor unit. Motorized damper will move to closed
position.
5. Remove jumper across “R” & “G” or return thermostat fan switch back to “AUTO” if desired.
6. Restore power back to unit.
SUPERSEDES 05-25-12
JUNE 5, 2012
FORM# NEI35OM06
HARNESS DETAIL
E# = WIRE END DESIGNATION
E2 STUD #6 18 Ga. Wire
E3 Female ¼ Quick Disc.
E4 Male ¼ Quick Disc. Insul
E6 Wire Nut Size 73B
COMPONENT CODE
CC
MAS
M847A
P1
S1
Compressor Contactor
Mixed Air Sensor
Damper Actuator 24V
Fresh Air Plug
Unit Fresh Air Plug
HARNESS ENDS AT P1
WIRE COLOR CODE
BLK
BLU
GRN
GRY
ORN
RED
VIO
WHT
YEL
Black
Blue
Green
Gray
Orange
Red
Violet
White
Yellow
Revision
Change
Date
A
Added jumper, MAS, and CC
06-26-09
B
Changed Note 2.
07-29-09
C
Changed Note 2.
05-25-12
CONNECTOR & CONTACT CONFIGURATION
P1 (30303903) PLUG - (30303912) PIN
Notes:
1. Unit wiring shown as reference only. Check unit wiring diagram for actual unit wiring.
2. S1 - Pin 2 Connection is :
A. Connection to "yellow" side of gas value on "R" Series Package Gas/Electric.
B. Connection is at "W" on "Q" and "P" Series units.
0-35% MOTORIZED FRESH AIR DAMPER
# 547840
R6G(D,F,I) / R8GD / P6SD / Q6SD 024-060
Date: May 25, 2012
Supercedes: 07-27-09
Drawn by: MGL
Unit #: 47-287-06
Diagram#: 4728706W
Approved by:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement