Bosch | Dryer | Instruction manual | Bosch Dryer Instruction manual

BOSCH
Use & Care Manual
Models
WTA3500
Electric Vented Dryer
WTL 5400
Electric Condensation Dryer
/
Quick Reference Index
IMPORTANT SAFETY INSTRUCTIONS
GROUNDING INSTRUCTIONS
2-3
3
ABOUT YOUR DRYER
GETTING TO KNOW YOUR DRYER
ENERGY SAVING TIPS
OPERATING TIPS
4
4
4
4
BEFORE USING THE FIRST TIME
GETTING STARTED
5
5
CYCLE SELECTION CHART, TABLE 1
6
OPERATION
6-8
CARE and CLEANING
LINT FILTER
HEAT EXCHANGER (WTL)
MOISTURE SENSOR
FROST PROTECTION
10
10
SERVICE and REPAIR
10
SELF-HELP, TABLE 2
11
WARRANTY
12
9
9
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
(In case of change of ownership, manual should be conveyed with the dryer.)
1
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock. serious injury or death to persons
when using your dryer, follow basic precautions, including the following.
1. Bosch dryers are provided with two manuals; one Installation Instruction manual and
one Use and Care manual. Read all instructions before using the dryer.
2. Do not dry articles that have been previously cleaned in, washed in. soaked in. or
spotted with gasoline, dry cleaning solvents, other flammable, or explosive substances
as they give off vapors that could ignite or explode.
3. Do not allow children to play on or in the appliance. Close supervision of children is
necessary when the appliance is used near children.
4. Before the appliance is removed from service or discarded, remove the door to the
drying compartment.
5. Do not reach into the appliance if the drum is moving.
6. Do not install or store this appliance where it will be exposed to the weather.
7. Do not tamper with the controls.
8. Do not repair or replace any part of the appliance or attempt any service unless
specifically recommended in the user-maintenance instructions or in published user
repair instructions that you understand and have the skills to carry out.
9. Do not use fabric softeners or products to eliminate static unless recommended by the
manufacturer of the fabric softener or product.
10. Do not use heat to dry articles containing foam rubber (may be labeled latex foam) or
similarly textured rubber-like materials. Foam rubber materials can, under certain
circumstances, when heated become ignited by spontaneous combustion.
11. Clean lint screen before or after each load.
12. Keep area around the exhaust opening and adjacent surrounding areas free from the
accumulation of lint, dust and dirt.
13. The interior of the machine and exhaust duct should be cleaned periodically by
qualified service personnel.
14. Always be sure to unplug the dryer from the electrical supply before attempting any
service. Disconnect the power cord by grasping the plug, not the cord.
15. Store all laundry chemicals and aids in a cool dry place according to the
manufacturer,s instructions in an area where children cannot reach them.
16. To reduce the risk of fire, clothes, cleaning rags, mop heads and the like which have
traces of any flammable substance, such as vegetable oil, cooking oil, petroleum
based oils or distillates. waxes, fats, etc., must not be placed in the dryer. These items
may contain some flammable substance(s) even after washing, which may smoke or
catch fire by itself.
17. Do not sit on top of the dryer.
18. To reduce the risk of fire or electrical shock, DO NOT use an extension cord or an
adapter to connect the dryer to the electrical power supply.
2
IMPORTANT SAFETY INSTRUCTIONS (continued)
19. The dryer must only be used for its intended purpose.
20. Always check and empty pockets of any objects that may have been forgotten.
Cigarette lighters, in particular, present a hazard that can be avoided by this process.
21. Replace worn power cords and/or loose plugs.
22. Do not operate the dryer with any guards and/or panels removed.
23. Do not operate the dryer with missing or broken parts.
24. Do not bypass any safety devices.
25. Do not use plastic or non-metal flexible duct with this dryer. Plastic or non-metal
flexible duct presents a potential fire hazard.
26. Do not operate this dryer until you are sure the dryer has been installed according to
the INSTALLATION INSTRUCTIONS and installation and grounding are in compliance
with all local codes and/or other applicable codes and requirements.
27. Failure to install, maintain and/or operate the dryer according to the manufacturer,s
instructions may result in conditions which can lead to bodily injury and/or property
damage.
Notes: A. The IMPORTANT SAFEGUARDS and WARNINGS presented in this manual do
not cover all possible conditions that may occur. Common sense, caution and
care must be exercised when installing, maintaining or operating the dryer.
B. Always contact your dealer, distributor, service agent or the manufacturer about
any problems or conditions that you do not understand.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a path of least resistance for the electric
current. This appliance is equipped with a cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
WARNING - Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt
as to whether the washer is properly grounded.
DO NOT modify the plug provided with the appliance - if it will not fit the outlet have a
proper outlet installed by a qualified electrician.
3
17 16
.,.,..
o
o..,Orr
-....0...
0
0
1~
.,
BOSCH
13
12
o-""
"1M!
o
4
5
678
9
~_ _=I-=rl- -
3
WTL 5400
WTA 3500
Figure 1.
ABOUT YOUR DRYER
Congratulations on having selected a Bosch clothes
dryer, the choice of those that demand exceptional
performance from their clothes dryer. The Bosch WTA
3500 and WTL 5400 dryers offer the following
standard features:
•
High Efficiency Precision Drying System with
Duotronic
•
Stainless Steel Drum
•
Exceptionally Quiet Operation
•
Condensation Drying allows vent free operation
•
Reverse Tumble Action
•
Sensor controlled Auto Cycles with 6 drying
levels and Timed Cycles from 10 to 90 minutes.
GETTING TO KNOW YOUR DRYER
Above you will find an illustration, Figure 1, showing
the location of the following:
1.
Door with lint filter
2.
Button to open the maintenance flap (WTL
models only)
3.
Heat Exchanger/lnlet panel (WTL models only)
4.
"ON/OFF" button
5.
"DOOR" button
6.
"START" button
7.
"DELICATES" button
8.
"END of CYCLE SIGNAL button
9.
"CYCLE TIME MINUTES" button
10. Time Cycles Selector Knob
11. Auto-Cycles Selector knob
12. Indicator lights for program selected
13. Indicator lights for time program selected
14. Lint Filter Cleaning indicator
n
4
15.
16.
17.
18.
Indicator lights for buttons
"Cycle Countdown Display"
Moisture Level indicator lights
Rating Plate location.
ENERGY SAVING TIPS
To save energy, time and money, Bosch recommends
the following:
• Always spin dry the wash in the washer at the
highest recommended speed for the fabric type.
The highest spin speed will result in a dryer load
and shorten the drying time and amount of
energy required to dry the load.
• Spin dry delicate washing before tumble drying.
• Load the dryer properly. Do not exceed the
maximum load (see CYCLE SELECTION
CHART).
• Always clean the lint filter after each use of the
dryer.
OPERATING TIPS
• Follow the fabric care labels on the clothing.
• Avoid very small loads. When only one or two
items need drying, add a few similar items to
improve drying efficiency.
• Do not mix heavyweight and lightweight clothing.
• Do not dry wool or fabrics with a wool content
• Do not dry fabrics that do not allow the free
passage of air (for example, GORTEX)
• Do not dry delicate fabrics such as, silk, synthetic
net curtains, etc.
BEFORE USING FOR THE FIRST TIME
Before beginning to use your dryer for the first
time:
1. Check to make sure that the voltage on which
the dryer is to operate is the same as shown
on the rating plate.
GETTING STARTED
Below, in order to get started, you will find a summary
of how to operate the clothes dryer. Also, refer to the
CYCLE SELECTION CHART, Table 1.
• Turn On the Dryer
Press the "ON/OFF" button. The indicator light
will become illuminated and the indicator above
the "START" button will begin to flash.
•
•
Check the Lint Filter
The lint filter, located in the door, should be
cleaned after or before each load.
•
Load the Dryer
Load the items in the dryer.
•
Add Fabric Softener Sheet
If a fabric softener sheet is to be added it should
be done after loading the dryer.
•
Close the Dryer Door
•
Select Cycle Desired
See CYCLE SELECTION CHART, Table 1, and
following section titled OPERATION for program
recommendations.
•
2. Wipe the interior of the drum with a damp
cloth.
Press the "START" Button
The "START" indicator lamp will stop flashing and
the dryer will start. If one of the Auto-Cycles have
been selected the Duotronic system will monitor
the moisture level and display the progress of the
drying in the "Moisture Level Indicator Lights." If a
timed cycle has been selected the minutes
remaining will be displayed in the "Cycle
Countdown Display."
The cycle will continue to the end, when the
"End" indictor lamp will become illuminated. And,
if the "End of Cycle Signal" has been selected a
signal will sound. - See following section
OPERATION on how to set or turn of the "End of
Cycle" signal.
•
Depress the "DOOR" Button
The door will open.
•
Remove the Laundry from the Dryer
•
Clean the Lint Filter
•
Turn Off the Dryer
Depress the "ON/OFF" button.
Select Additional Functions (if desired)
See following section titled OPERATION.
5
-
CYCLE SELECTION CHART (Recommendations)
--
--
-~--~
ELECTRONIC AUTO DRY CYCLES
Cotton or linen items (whites and coloreds), full load *
Note: For heat-sensitive items press the "DELICATES" button.
for laundry which will be ironed with
Bed and table linen, towels
a mangle (rotary iron)
Bed and table linen, towels, T-shirts,
for laundry which will be ironed with
a steam iron
work clothes
T-shirts, trousers, work clothes,
for laundry which will be ironed
underwear
lightly, or not at all
Bath towels, tea towels, hand towels,
for laundry which will not be ironed
bed linen, underwear, cotton socks
Bath towels, tea towels, hand towels,
for thick, multi-layered materials
bed linen, underwear, cotton socks
which will not be ironed
Flannel dressing gowns and bed linen
particularly thick or multi-layered
(no underwear or socks)
materials
Permanent Press items (non-iron items) made of synthetic and mixed fibers
and non-iron cottons, ~ load *
Note: For heat-sensitive fabrics press the "DELICATES" button.
Trousers, skirts, dresses, shirts
for laundry which will be ironed with
a steam iron
for laundry which will be ironed
Synthetic trousers, skirts, dresses, shirts,
either lightly, or not at all
blouses, leggings and sportswear
Shirts, blouses, sportswear
for laundry that will not be ironed
Bed and table linen, jogging suits
for thick, multi-layered materials
which will not be ironed
(sweats)
Parkas (anoraks), bed covers
particularly thick or multi-layered
materials
Timed Cycles
Pre-dried fabrics with low moisture content and separate, small items
All fabrics or items needing freshening, tumbles without heat
• - Refers to full and half loads from Bosch tumble action clothes washer.
Table 1.
OPERATION
Below you will find a more detailed explanation of the
operation of your dryer:
1. Turn the machine on
Depress the "ON/OFF" button. The indicator light
above the button will become illuminated
indicating that the machine is on and the light
above the "START' button will flash.
2. Check the Lint Filter.
The lint filter, located in the door, should be
cleaned after or before each load. Check the lint
filter and if it was not cleaned after last use clean it
now. Cleaning the filter will shorten drying times
and save energy.
Figure 2.
6
Drying t..eve/ Setting
Regular/Cott.
Damp Dry
Econo Dry
Light Dry
Regular Dry
Very Dry
Extra Dry
Permanent Press
Econo Dry
Light Dry
Regular Dry
Very Dry
Extra Dry
Heated Dry:
10-90 min.
Air Fluff: 10-90 min.
3. Load the dryer
For best results it is recommended that the drying
load be sorted by fabric type and desired dryness
level. Also, close all zippers, hooks and eyelets
and tie loose belts and apron strings, etc. before
placing in the dryer.
a. Depress the "DOOR" button. The door will open
and the drum light will turn on.
b. Check the drum interior for foreign objects or
pets and remove any used fabric softener
sheets.
c. Place laundry items to be dried loosely into the
drum of the dryer.
4. Add Fabric Softener Sheet, if desired
If a fabric softener sheet is to be added it should
be done after loading the dryer and before the
dryer and load become warm. This will prevent
greasy-looking softener stains.
Timed Cycles
0(9
o
o
Air Fluff
b. To use Time Cyles (dryer runs for selected
length of time) activate by turning the time
program selector (see Figure 4):
i. Heated Dry
The Time Cycle's knob should be turned to
point to the right to select the Heated Dry
setting. Then depress the "Cycle Time
Minutes" button to set the time interval for
drying. The time can be set at 10 - 90
minutes in 10 minute steps.
or,
Note: If the door is not fully closed the dryer will
not operate.
ii. Permanent Press
The Auto-Program knob should be turned to
point to the left to select Permanent Press
settings. As the knob is turned the lights
directly above the knob will illuminate to
indicate the level of dryness selected. See
Table 1 for recommended settings for type
of load being dried.
o
o
Figure 3.
Check the area around the drum opening to make
sure that nothing is caught on the edge or hanging
outside the drum and close the door making sure
the door clicks into place and is fully closed.
or,
o
Heated Dry
5. Close the Door
6. Select the Drying Cycle Desired
The Bosch dryers can be operated in either the
Electronic Auto Dry Cycle mode, which uses the
Duotronic moisture sensing system, or in Time
Cycle mode, which uses a timer to control the
length of the program. See below and CYCLE
SELECTION CHART, Table 1, for program
recommendations:
a. To use Electronic Auto Dry Cycles
(dryer runs until the drying level selected has
been reached) activate by turning the Cycle
Selector knob (see Figure 3) to:
i. Regular /Cott.
The Auto-Program dial should be turned to
point to the right to select Regular/Cott.
settings. As the knob is turned the lights
directly above the knob will illuminate to
indicate the level of dryness selected, from
Extra Dry through Damp Dry. See Table 1
for recommended settings for type of load
being dried.
Permanent 0 .Regular/Cott.
Press
0 Extra Dry
Very Dry
• Regular Dry
o Light Dry
Econo Dry
Damp Dry
ii. Air Fluff (cold)
The Time Cycle's knob should be turned to
point the left to select the Air Fluff setting.
Then depress the "Cycle Time Minutes"
button to set the time interval for drying. The
time can be set at 10 - 90 minutes in 10
minute steps.
Note: The Auto-Program knob must be
pointing straight-up to use Time Cycles.
Cycle Countdown
t.'iDO.i.
:.~.:r1, '!:::•. J <.9
Cycle TIme
Minutes
I
•
=
=
UntFilter
o
TImed Cycles
.<.9
•
Heated Dry
Air Fluff
o
Permanent 0 0 Regular/Cotl.
Press
0 Extra Dry
o Very Dry
o Regular Dry
o Light Dry
o Econo Dry
o Damp Dry
,
aD
Figure 4.
7
The program will continue to the end, when the
"End" indicator lamp will become illuminated. And
if the "End of Cycle Signal" has been selected a
signal will sound.
7. Select ADDITIONAL FUNCTIONS, if desired
The additional functions available are accessible
by depressing the buttons:
"DELICATES"
The "DELI CATES" button, see Figure 5, will
reduce the drying temperature and lengthen the
drying time when depressed. It is recommended
that the "DELICATES" button be depressed when
drying heat sensitive fabrics, such as, acrylics. Be
sure to follow the instructions listed on the care
label instructions.
Note: If the load is not removed, the drum will, for
the following 35 minutes, rotate at brief
intervals to prevent wrinkling (Anti-Crease).
After 35 minutes this feature will cease its
function. It is recommended that the dryer
be unloaded no later than 35 minutes after
completion of program to avoid wrinkling.
"END OF CYCLE SIGNAL"
When the "END of CYCLE SIGNAL" button, see
Figure 5, is activated there will be a signal
sounded at regular intervals at completion of the
selected program.
0ryInQ
o
8. Press the "START" Button
Depress the "START" button. The indicator light
above the "START" button will become illuminated
and the machine will start. If one of the Auto
Cycles has been selected the Duotronic system
will continuously monitor the moisture level of the
load and display the progress in the "Moisture
Level Indicator Lights." If a timed cycle has been
selected, either Heated Dry or Air Fluff, the
minutes remaining in the program will be shown in
the "Cycle Countdown Display."
8
R<9ula, DI)'
000
Start
IO
The volume level of the sound may be changed by
holding the button in until desired volume level is
reached. This volume level will be stored for future
use until altered.
The end of cycle signal can be switched off by
depressing the button again. The indicator light
above the button will turn off to indicate that the
signal is no longer selected.
Damp DI)'
0
Extra Dry
Anti-Crease/End
Icales
Deli- IEnd Df Cycle
Signal
o
0
~~
c:=:=::=> c::::;::::::::: c::::z::::::>
~
~~~
c=::::z=)
Cycle Counldown
<9
Cycle TIme
Minutes
Io
=
=
Figure 5.
9.
Depress the "DOOR" button
The door will open.
10. Remove the Laundry from the Dryer
11. Clean the Lint Filter
The lint filter, located in the door, should be
cleaned after each load. Cleaning the filter will
shorten drying times and save energy.
12. Turn Off the Dryer.
Depress the "ON/OFF" button.
CARE and CLEANING
The housing and control panel should only be
cleaned with a soft cloth rinsed in soapy water, or
with a solvent free, non-scouring cleaning agent.
Other areas requiring periodic leaning or
maintenance are listed below:
Lint Filter
The lint filter should be cleaned after each use, If the
"Lint Filter" light becomes illuminated and the buzzer
sounds during operation of the dryer:
1. Immediately stop the dryer by depressing the
"ON/OFF" button.
2. Depress the "DOOR" button and open the door.
3. Remove the filter.
4. Clean the filter.
5. Replace the filter.
6. Let the dryer cool down.
7. Close the door.
8. Press the "START" button to restart the dryer.
Heat Exchanger (WTL models only)
The heat exchanger should be cleaned 3-4 times a
year; more often if used frequently. To clean the heat
exchanger:
1. With the dryer turned off and disconnected from
the electrical supply. Disconnect the power cord by
grasping the plug, not the cord.
2. Depress the "DOOR" button and open the door.
3. Press the button for opening the heat
exchanger/inlet panel, as shown in Figure 6.
Figure 7.
Figure 8.
8.
Allow heat exchanger to dry thoroughly before
reinserting into the dryer.
9. Once the heat exchanger is completely dry,
reinsert it into the dryer. The handle must be
underneath the heat exchanger. Turn the
retainers back to their original position.
10. Close the heat exchanger/inlet panel by pressing
firmly on both the upper left and right hand sides,
as shown in Figure 9, until it snaps into place.
Note: The dryer door will only be able to be closed if
the heat exchanger/inlet panel is properly
closed and locked in place.
Figure 6
4. Open the panel fully.
5. Turn the retainers on each side of the heat
exchanger towards each other, in the direction of
the arrows as shown in Figure 7.
6. Remove the heat exchanger by slowly pulling it
forward and out of the dryer.
7. Clean the heat exchanger thoroughly with water.
Allow the water to run freely through the heat
exchanger. See Figure 8.
Figure 9.
9
Moisture Sensor
Occasionally the moisture sensors will need cleaning,
due to a build-up of a fine layer of lime scale on the
inside of the drum. This build-up of lime scale can be
easily removed by wiping the sensors, the metal
inserts in the paddles, and the inside of the drum with
a soft cloth soaked in vinegar (use white vinegar).
See Figure 10.
Frost Protection (WTL models only)
The WTL models, since they remove moisture by
condensing the water out of the air and then pumping
the water to drain, should never be installed in an
area subject to freezing. Also, if the dryer is to be
transported where it would be subjected to freezing
the dryer must be completely emptied of water before
transporting.
Figure 10.
SERVICE and REPAIR
The Bosch dryers require no special care other than
the care and cleaning noted above. If you are having
a problem with your dryer, before calling for service
please refer to Table 2, SELF-HELP section,
following. If service becomes necessary, contact your
dealer or installer or an authorized service center. Do
not attempt to repair the appliance yourself. Any work
performed by unauthorized personnel may void the
warranty.
If you are having a problem with your Bosch washer
and are not pleased with the service you have
received:
•
First, please contact your installer or the Bosch
Authorized Service Contractor in your area and
explain to them why you are not satisfied. This
will usually correct the problem.
• If after working with your installer or service
person the problem still has not been resolved to
your satisfaction, please let us know by either
writing to us at,
BSH Home Appliances
2800 South 25th Avenue
Broadview, IL 60153
or, calling us at,
1-800/944-2904.
10
Please be sure to include, if writing, or have
available, if calling, the following information:
•
Model Number
• Serial Number
• Date of Original Purchase
• Date Problem Originated
• Explanation of Problem
Also, if writing, please be sure to include a daytime
telephone number.
You will find the model number and serial number
information on the rating plate located on the inside
of the door above the lint filter. See Figure 1.
SELF-HELP
Dryers may exhibit problems that are unrelated to a malfunction of the dryer itself. The following table may serve
to answer your question about a problem you are having without having to call a serviceman.
PROBLEM
"On/Off' Indicator light do not
come on
Dryer does not start
Cycle is interrupted and "Lint
Filter" light is illuminated and
buzzer sounds
Cycle is interrupted, buzzer
sounds. one or several cycle
indicators are flashing
Drying level not reached or
drying time too long
The laundry is not dry even
though the highest drying level
has been selected
Drum light does not work
POSSIBLE CAUSE
• The "ON/OFF" has not been depressed
• A fuse may have blown or a circuit breaker tripped. Replace fuse or
reset circuit breaker at your fuse box/breaker box.
• The plug is not correctly or only loosely inserted into the receptacle.
• Cycle has not been selected.
• "START" button has not been depressed.
• Door is not closed properly.
• Room temperature is below 32°F (O°C)
• If necessary. switch the machine off and wait 5 seconds before
switching it on again. Select the cycle again and depress "START".
• Clean Lint Filter as described in section titled CARE & CLEANING.
• (WTA models) Check exhaust vent to see if it is blocked or too long.
• (WTL models) Clean heat exchanger as described in section titled
CARE & CLEANING.
• (WTL models) Check air inlet to make sure it is not blocked.
• Indicates faulty operation:
- Clean the Lint Filter, check the exhaust duct length (WTA models).
- Switch the dryer off, wait for it to cool down and then restart.
• Clean the Moisture sensors in the drum as described in section titled
CARE & CLEANING.
• If there is a power failure for an extended period the cycle must be
restarted.
• The drum is too full
• The laundry was too wet when placed in the dryer
• The room is not adequately ventilated. Make sure there is an
adequate supply of fresh air.
• The lint filter is blocked and should be cleaned.
• (WTA models) The exhaust vent is blocked or too long.
• (WTL models) The air inlet is blocked.
• "ON/OFF" button has not been pressed
• Bulb has failed. For safety reasons the bulb must onjy be replaced by
. ,
an authorized service agent.
Following items apply only to the WTL (Condensation Electric Dryer) models
Cycle is interrupted and "E1"
• Water condensate hose is blocked in some way. Turn off dryer and
appears in display
check hose.
Humidity level in room
• The room is not adequately ventilated. Make sure there is an
increases greatly
adequate supply of fresh air.
• Check air inlet to see if it is blocked
• The heat exchanger was removed but not replaced.
TABLE 2.
Il
STATEMENT OF WARRANTIES
BOSCH CLOTHES DRYERS
The warranties provided by BSH Home Appliances ("Bosch") in this Statement of Warranties apply only to Bosch clothes
dryers sold to the first using purchaser by Bosch or its authorized dealers, retailers or service centers in the United States or
Canada. The Warranties provided herein are not transferable.
LENGTH OF WARRANTY
SCOPE OF WARRANTY
1 Year Full Limited Warranty
From Date of Installation·
Bosch will repair or replace, free of charge, any component
part that proves defective under conditions of normal home
use labor and shipping costs included. Warranty repair
service must be performed by an authorized Bosch Service
Center (excludes cosmetic parts).
2 Year Limited Warranty
Bosch will provide replacement parts, free of charge, for any
component part that proves defective under conditions of
normal home use, shipping costs included.
From Date of Installation·
5 Year Limited Warranty on Electronics
From Date of Installation·
Bosch will repair or replace, free of charge, any
microprocessor or printed circuit board that proves
defective under conditions of normal home use for a period
of five years from the date of original installation, labor
charges excluded.
5 Year Limited Warranty on Motor
From Date of Installation·
Bosch will repair or replace, free of charge, any motor or
component part of the motor that proves defective under
conditions of normal home use for a period of five years
from the date of original installation, labor charges excluded.
5 Year Limited Warranty on Cabinet Rust
Bosch will replace any cabinet part, free of charge, if that
cabinet part should rust through under conditions of normal
home use, labor charges excluded.
From Date of Installation·
Lifetime Limited Warranty against Stainless Steel Rust
Through
From Date of Installation·
Bosch will replace your clothes dryer, free of charge, with
the same model or a current model that is eqUivalent or
better in functionality if the dryer drum should rust through
under conditions of normal home use, labor charges
excluded .
• Date of installation shall refer to the earlier of the date the clothes dryer is installed or ten business days after the delivery date.
Exclusions.
This warranty does not cover service calls or repairs to correct the installation of the clothes dryer, to provide instructions on the use of your
clothes dryer, to replace house fuses or correct plumbing or the electric wiring in your home or to repair any clothes dryer that's use was in a
manner other than what is normal and customary for home use. In addition, the warranties provided in this Statement exclude any defects or
damage arising from accident, alteration, misuse, abuse, improper installation, unauthorized service work, external forces beyond Bosch's
control, such as fire, flood, and other acts of God, or installation not in accordance with local electrical and plumbing codes. Labor charges
incurred in the repair or replacement of any clothes dryer after a period of one year from date of installation shall not be covered by this
warranty. Any and all replaced and/or repaired parts shall assume the identity of the original for purposes of the applicable warranty period.
TO THE EXTENT PERMITIED BY LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BSH DOES NOT
ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
TO OBTAIN WARRANTY SERVICE, CONTACT THE NEAREST BOSCH AUTHORIZED SERVICE CENTER OR CALL 1-800-944-2904, OR
WRITE AT: BSH HOME APPLIANCES, ATIN. SERVICE, 2800 SOUTH 25TH AVENUE, BROADVIEW, ILLINOIS 60153. BE SURE TO
PROVIDE YOUR CLOTHES DRYER'S MODEL, SERIAL NUMBER, PURCHASE DATE AND THE SELLER'S NAME AND ADDRESS.
5080008 AA2
12
Download PDF

advertising