Plus Quick Installation Guide  3.  Board Layout
3.
Board Layout
STEP 5: Connect the cables.
STEP 6: Turn the embedded computer on. The BIOS will automatically
set the IRQ and I/O address.
CB-108
CB PC/104-Plus
Quick Installation Guide
Box Header Connector
PC/104 Slot
Second Edition, June 2008
1.
5.
PC/104-Plus Slot
Overview
The CB Series multiport serial module provides serial port expansion for
embedded PCs. It is designed for PC/104-Plus CPU boards that accept the
PC/104-Plus expansion interface. Optional DB9 and DB25 cables are
available to connect different devices. The device drivers make full use of
the 128-byte Tx/Rx FIFO and on-chip flow control, which allows up to
921.6 Kbps data transmission. Three different models are available as
follows:
CB-114
PC/104-Plus Slot
SW1
SW2 Serial Interface
SW3
Box Header Connector
PC/104 Slot
y CB-108: 8 ports, RS-232
y CB-114: 4 ports, RS-232/422/485
y CB-134I: 4 ports, RS-422/485 w/ 2 KV optical isolation protection
2.
Interface
RS-232
RS-422
4-wire RS-485
2-wire RS-485
Package Checklist
Before installing the CB Series PC/104-Plus multiport serial module,
verify that the package contains the following items:
y CB Series PC/104-Plus multiport serial module
S1
----ON
OFF
S2
--ON
OFF
OFF
S3
ON
OFF
OFF
OFF
CB-134I
y Documentation and Software CD-ROM
PC/104-Plus Slot
RS422/RS485
2-WIRE/4-WIRE
y Quick Installation Guide
y 5-year product warranty statement
Please notify your sales representative if any of the above items are
missing or damaged.
Box Header Connector
PC/104 Slot
Interface
RS-422
4-wire RS-485
2-wire RS-485
4.
2-WIRE/4-WIRE
--OFF
ON
RS422/RS485
OFF
ON
ON
Hardware Installation Procedure
Do not install the drivers until the module has been installed in the
embedded computer. Install the module in the embedded computer as
follows:
P/N: 180200104A000
— 1 —
STEP 1: Turn the embedded computer off.
STEP 2: On the module, select the serial interface using the DIP
switches.
STEP 3: Insert the module firmly into an available PC/104-Plus slot.
STEP 4: Screw the control board in place.
— 2 —
Software Installation Procedure
For detailed software installation instructions, please refer to the CB
Series User’s Manual.
Windows Vista (32-bit)
1.
Windows will automatically detect the module on boot-up.
2.
Insert the Document and Software CD in your CD-ROM drive.
3.
Select Locate and install driver software (recommended).
4.
A window will appear stating that “Windows needs your permission
to continue”. Click Continue.
5.
A window will appear requesting that you “Insert the disc that came
with your PCI Serial Port”. Select I don’t have the disc, show me
other options.
6.
Select Browse my computer for driver software (advanced).
7.
For 32-bit (x86) platforms, select the \CB
Series\Software\Windows Vista\x86 folder on the CD and click
Next to continue.
8.
If you see a warning that the software has not passed Windows
Logo testing, click Install this driver software anyway.
9.
After the module is installed, the installation wizard will guide you
through port installation, starting with port 0.
10. Use Windows Device Manager to verify that the installation was
successful. Click the + sign next to Hardware and check under
Multi-port serial adapters and Ports (COM & LPT). If there are
any special marks in front of the board or port icons, such as a
question mark or exclamation point, you may refer to the Event
Log to try and determine where the problem is.
Windows 2003 and XP (32-bit, 64-bit)
1.
Windows will automatically detect the module on boot-up.
2.
Insert the Document and Software CD in your CD-ROM drive.
3.
Select No, not this time.
4.
Select Install from a list or specific location (Advanced).
5.
Select Search for the best driver in these locations, Include this
location in the search, and click Browse.
Š For 32-bit (x86) platforms, select the \CB
Series\Software\Windows XP_2003\x86 folder on the CD
Š For 64-bit (x64) platforms, select the \CB Series
\Software\Windows XP_2003\x64 folder on the CD.
Click Next to continue.
6.
If you see a warning that the software has not passed Windows
Logo testing, click Continue Anyway.
7.
After the module is installed, the installation wizard will guide you
through port installation, starting with port 0.
— 3 —
8.
Use Windows Device Manager to verify that the installation was
successful. Click the + sign next to Hardware and check under
Multi-port serial adapters and Ports (COM & LPT). If there are
any special marks in front of the board or port icons, such as a
question mark or exclamation point, you may refer to the Event
Log to try and determine where the problem is.
Windows 2000
1.
Windows will automatically detect the module on boot-up.
2.
Insert the Document and Software CD in your CD-ROM drive.
3.
Select Search for a suitable driver for my device
(recommended).
4.
Select Specify a location.
5.
Under Optional search location, select specify a location. Select
the \CB Series\Software\Windows 2K folder on the CD and click
OK to continue.
6.
If you see a warning that the software has not passed Windows
Logo testing, click Yes to proceed with the installation.
7.
After the module is installed, the installation wizard will guide you
through port installation, starting with port 0. Be sure to install the
software from the \CB Series \Software\Windows 2K folder on the
CD.
8.
Use Windows Device Manager to verify that the installation was
successful. Click the “+” sign next to Hardware and check under
Multi-port serial adapters and Ports (COM & LPT). If there are
any special marks in front of the board or port icons, such as a
question mark or exclamation point, you may refer to the Event
Log to try and determine where the problem is.
RS-422, 4-wire RS-485 (CB-114, CB-134I)
Pin Signal Pin Signal Pin Signal
1 TxD0-(A) 11 TxD1-(A) 21 TxD2-(A)
2
12
22
3 TxD0+(B) 13 TxD1+(B) 23 TxD2+(B)
4
14
24
5 RxD0+(B) 15 RxD1+(B) 25 RxD2+(B)
6
16
26
7 RxD0-(A) 17 RxD1-(A) 27 RxD2-(A)
8
18
28
9
GND0
19
GND1
29
GND2
10
20
30
1
6
Pin Assignment and Cable Wiring
The box header connector on the module can be used with optional serial
cables to connect to your serial devices. The pin assignments are as
follows:
RS-232 (CB-108, CB-114)
Pin Signal Pin Signal
1
DCD0
11
DCD1
2
DSR0
12
DSR1
3
RxD0
13
RxD1
4
RTS0
14
RTS1
5
TxD0
15
TxD1
6
CTS0
16
CTS1
7
DTR0
17
DTR1
8
--18
--9
GND0
19
GND1
10
--20
---
Pin
21
22
23
24
25
26
27
28
29
30
— 4 —
Signal
DCD2
DSR2
RxD2
RTS2
TxD2
CTS2
DTR2
--GND2
---
Pin
31
32
33
34
35
36
37
38
39
40
Signal
DCD3
DSR3
RxD3
RTS3
TxD3
CTS3
DTR3
--GND3
---
Signal
TxD3-(A)
TxD3+(B)
RxD3+(B)
RxD3-(A)
GND3
2-wire RS-485 (CB-114, and CB-134I)
Pin Signal Pin Signal Pin Signal Pin Signal
1
11
21
31
2
12
22
32
3
13
23
33
4
14
24
34
5 Data0+(B) 15 Data1+(B) 25 Data2+(B) 35 Data3+(B)
6
16
26
36
7 Data0-(A) 17 Data1-(A) 27 Data2-(A) 37 Data3-(A)
8
18
28
38
9
GND0
19
GND1
29
GND2
39
GND3
10
20
30
40
1
5
Linux
Please refer to the user’s manual for instructions on installing the Linux
drivers.
6.
Pin
31
32
33
34
35
36
37
38
39
40
14
9
DB9 (M) connectors
(CBL-F40M9x4-50,
CBL-F20M9x4-50)
RS-422,
4-wire
2-wire
RS-485
Pin RS-232 RS-485
1 DCD TxD-(A)
--2 RxD TxD+(B)
--3
TxD RxD+(B) Data+(B)
4 DTR RxD-(A) Data-(A)
5 GND
GND
GND
6 DSR
7
RTS
8
CTS
13
25
DB25 (M) connectors
(CBL-F40M25x4-50,
CBL-F20M25x4-50)
RS-422,
4-wire
2-wire
RS-485
Pin RS-232 RS-485
2
TxD RxD+(B) Data+(B)
3
RxD TxD+(B)
--4
RTS
----5
CTS
----6 DSR
----7 GND
GND
GND
8 DCD TxD-(A)
--20 DTR RxD-(A) Data-(A)
— 5 —
Click here for online support:
www.moxa.com/support
The Americas:
Europe:
Asia-Pacific:
China:
+1-714-528-6777 (toll-free: 1-888-669-2872)
+49-89-3 70 03 99-0
+886-2-8919-1230
+86-21-5258-9955 (toll-free: 800-820-5036)
© 2008 Moxa Inc., all rights reserved.
Reproduction without permission is prohibited.
— 6 —
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement