x Permacron 1:1 Elastic Primer Surfacer 3300

x Permacron 1:1 Elastic Primer Surfacer 3300
Technical Data Sheet – 310.1
Permacron®
1:1 Elastic Primer Surfacer 3300
GENERAL
DESCRIPTION
A universal 2K Primer Surfacer for all plastic parts commonly found on passenger vehicle
exteriors.
This economical primer surfacer can be recoated directly with an elastic base coat. It is
characterized by good adhesion, high elasticity, and easy application. Permacron® 1:1
Elastic Primer Surfacer 3300 is available in gray and black.
The products referenced herein may not be available for sale in your market. Please
consult your distributor for product availability.
MIXING
COMPONENTS
Permacron® 1:1 Elastic Primer Surfacer 3300
PERMACRON ELASTIC HARDENER
Permacron® Elastic Hardener 3301
MIX RATIO
Component
3300
3301
Volume
1
1
APPLICATION VISCOSITY
Approximately 17 – 21 seconds at 68°F/20°C, DIN 4
POT LIFE
Approximately 8 hours at 68°F/20°C
SPECIAL TIPS
1. Do not allow Permahyd® Plastic Cleaning Paste 7081 to dry on the surface of the plastic
substrate.
2. Thoroughly clean and scuff all surfaces of the plastic part, paying special attention to all
edges.
3. For hard to reach areas of the plastic part, use the application brush that is included
with the Permahyd® Plastic Cleaning Paste 7081.
4. Permahyd® Plastic Cleaning Paste 7081 is designed for raw plastic and is not suitable
for cleaning painted surfaces.
5. Always use a clean scuff pad.
6. Soft plastic may require a finer scuff pad.
7. Difficult to clean plastics may need to be cleaned more times, or if applicable the plastic
may be baked for a minimum of 15 minutes at 140°F (60°C). Some OEM plastic
bumpers do not recommend a bake cycle. Once the plastic has cooled, repeat the
procedure below for preparing raw plastics beginning with step 2.
Plastic parts repaired with Permacron® 1:1 Elastic Primer Surfacer 3300 may not be washed
with a high pressure jet within six weeks of the repair. After this period, the nozzle must be
held at a distance of no less than 12 inches from the object.
Page 1 of 4
Technical Data Sheet – 310.1
APPLICATION
SUBSTRATES
All raw plastic parts commonly found on vehicle exteriors (Examples: PP, PP/EPDM, ABS,
SAN, PC, PA, PUR-RIM, R-TPU, TPO, PBTP, UP-GF).
Not recommended for pre painted substrates.
SURFACE PREPARATION
Primed Plastic
Perform a solvent test to check if primer is reversible.
1. If the primer is reversible, then strip and treat as raw plastic.
2. If the primer is not reversible
a. Wash with soap and water, clean with Permaloid® Silicone Remover 7010
Slow, Permahyd® Silicone Remover 7085, or Permahyd® Silicone Remover
7096. Sand primer (with P500-800 when dry sanding or with P600-800 when
wet sanding). Make sure to scuff all of the edges and hard to reach areas with
a gray or gold scotch pad.
b. Re-clean with Permaloid® Silicone Remover 7010 Slow, Permahyd® Silicone
Remover 7085, or Permahyd® Silicone Remover 7096.
c. Apply Permacron® 1:1 Elastic Primer Surfacer 3300 as per below and recoat
with Permacron® Base Coat Series 293/295 or Permahyd® Hi-TEC 480.
Raw Plastic
The substrate must be free from release agents.
1. Rinse the raw plastic part thoroughly with water and pre-clean it using Permahyd®
Plastic Cleaning Paste 7081 and a clean gold scuff pad.
2. Continue to clean the raw plastic part another 2 to 3 times using new Permahyd ®
Plastic Cleaning Paste 7081 and a clean gold scuff pad. The supplied brush
should be used with Permahyd® Plastic Cleaning Paste 7081 in hard to reach
areas of the plastic part.
3. Remove all Permahyd® Plastic Cleaning Paste 7081 residue from the plastic by
thoroughly rinsing with clean water.
4. Before further treatment, clean the plastic substrate thoroughly with Permaloid 
Silicone Remover 7010 Slow, Permahyd Silicone Remover 7085, or Permahyd
Silicone Remover 7096.
5. Apply Permacron® 1:1 Elastic Primer Surfacer 3300 as per below and recoat with
Permacron® Base Coat Series 293/295 or Permahyd® Hi-TEC 480.
SPRAYGUN SETUP
HVLP
Approved Transfer Efficiency
1.3-1.4mm
1.2-1.3mm
Please refer to gun manufacturer and local legislation for proper spray pressure
recommendations.
APPLICATION

Apply 1.5 coats (one tack coat followed by one full coat to obtain opacity).
RECOMMENDED FILM THICKNESS
Approximately 1.2 mil dry film thickness
Page 2 of 4
Technical Data Sheet – 310.1
DRY TIMES
AIR DRYING
Drying time at 68°F/20°C:
Base Coat Series 293/295
15-20 min. or max. 8 hrs. prior to Permacron®
20-30 min. prior to Permahyd® Hi-TEC 480
2 hours prior to sanding
LOW BAKE
Drying time at 140°F/60°C metal temp.:
30 minutes
WET SANDING
Initial sanding: P320
Final sanding: P600 – 800
RECOAT
With Permacron® Base Coat Series 293/295 or Permahyd® Hi-TEC 480
PHYSICAL PROPERTIES
Coating Category: Primer
Max. VOC (AP): 662 g/l; 5.5 lbs/gal
Max. VOC (LE): 662 g/l; 5.5 lbs/gal
Avg. Gallon Weight: 1048.1 g/l; 8.75 lbs/gal
Avg. Weight % Volatiles: 63.2%
Avg. Weight % Water: 0.0%
Avg. Weight % Exempt Solvent: 0.0%
Avg. Volume % Water: 0.0%
Avg. Volume % Exempt Solvent: 0.0%
Theoretical Coverage @ 1 mil: 378.5 sq/ ft.
Theoretical Coverage @ Recommended Film Build: 252 sq/ ft.
VOC REGULATED AREAS
These directions refer to the use of products which may be restricted or require special
mixing instructions in VOC regulated areas. Follow mixing usage and recommendations in
the VOC Compliant Products Chart for your area.
SAFETY AND HANDLING
For industrial use only by professional, trained painters. Not for sale to or use by the general
public. Before using, read and follow all label and MSDS precautions. If mixed with other
components, mixture will have hazards of all components.
Ready to use paint materials containing isocyanates can cause irritation of the respiratory
organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with
a history of respiratory complaints must not be asked to work with products containing
isocyanates.
Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying
respirator with particulate filters or appropriate ventilation, and gloves.
Any analytical results set forth herein do not constitute a warranty of specific product
features or of the product’s suitability for a specific purpose. All products are sold pursuant
to our general conditions of sale. We hereby disclaim all warranties and representations,
express or implied, with respect to this product, including any warranty of merchantability or
fitness for a particular purpose. This product is protected by patent law, trademark law,
Page 3 of 4
Technical Data Sheet – 310.1
copyright law, international treaties and/or other applicable law. All rights reserved.
Unauthorized sale, manufacturing or use may result in civil and criminal penalties
Revised: April 2016
Page 4 of 4
©2014, 2016 Axalta Coating Systems, LLC and all affiliates. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement