RT Slip-On (2010)

RT Slip-On (2010)
Installation Instructions
1. Make sure the bike is completely cool before starting the
installation. Make sure the bikes parking brake is set.
7. Install supplied TBR muffler hanger bracket using the
OEM bolt and nut.
2. Remove OEM heat shield.
2010 Can-Am
V.A.L.E.
TM
V a r i a b l e
A x i s
L o c k i n g
E x h a u s t
SPYDER RT
V.A.L.E.™ Slip-on Exhaust System with M-5 Canister
Part # 005-2830419V / 005-2830420V
3. Remove OEM muffler joint.
4. Remove OEM muffler mounting bolt, this bolt will
be re-used.
8. Loosely attach TBR slip-tube to muffler using the supplied
2-piece X-ring with the supplied (4) 6x20mm socket head
cap screws and lock washers.
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions first before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Be sure
to save all stock components for possible use later.
**This product has not been tested with all available accessories and some
items may cause excessive heat. Excessive heat may cause damage to your
vehicle. Two Brothers Racing will not be responsible for damaged parts.
5. Remove OEM muffler assembly.
6. Remove OEM muffler joint gasket.
Installation Instructions
9. Loosely Install supplied barrel-clamp on slip-tube end.
10. Install rubber lined muffler clamp over TBR muffler
assembly.
14. Install TBR heat shield to slip-tube using the OEM heat
shield mounting bolts.
V.A.L.E.
TM
2010 Can-Am
V a r i a b l e
A x i s
L o c k i n g
E x h a u s t
SPYDER RT
V.A.L.E.™ Slip-on Exhaust System with M-5 Canister
Part # 005-2830419V / 005-2830420V
11. Install TBR muffler assembly to motorcycle and attach
muffler clamp using the supplied 8x30mm socket head
cap screws and 8mm lock nut.
15. Double check all your work.
16. Before you run the bike, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run
the bike and enjoy. It is normal for some white smoke to
appear the first time you start the bike. This is packing/
manufacturing oil from inside the pipe burnin g off.
Check for gaps or leaks. If you find a leak, a little high
temperature silicon sealant should fix it. After 50 to 100
miles, recheck all fasteners for tightness.
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
12. Make adjustments to get muffler alignment straight and
tighten muffler clamp, X-ring bolts and joint clamp.
Parts List
Qty.
Description
Part Number
1
1
1
1
2
4
4
1
1
1
1
1
1
1
1
M-5 Muffler Canister Slip-On Tube Muffler Clamp
HARDWARE KIT
X-Ring (half)
6x20mm Socket Head Cap Screw
6mm Lock Washer
Barrel Clamp 66mm
Spyder Heat Shield
Spyder Mounting Bracket
8x30mm Socket Head Cap Screw
8mm Lock Nut
5mm Long Handle Ball End Hex Key
T20 Torx Short Hex Key
TBR Sticker Kit
Varies
005-28304S
005-53C
005-283-3
005-7-2-3
005-SH620
005-WL6
005-27-66MSH
005-283-HS
005-283-B
005-SH830
005-FNL8
005-9-18610
005-9-15820
015-10212
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
13. Remove 2 clip-nuts from OEM heat shield bracket and
install on TBR slip-tube.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only,
and therefore are sold “as is” without warranty. Two Brothers Racing specifically disclaims
any warranties of merchantability or fitness for a particular purpose and disclaims all
responsibility for consequential and incidental damages or any other losses arising from
the use of these products or parts.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement