USER GUIDE & INSTALLATION INSTRUCTIONS Classic | Rangemaster | Toledo

USER GUIDE & INSTALLATION INSTRUCTIONS Classic | Rangemaster | Toledo
Built from experience
USER GUIDE &
INSTALLATION INSTRUCTIONS
Classic | Rangemaster | Toledo
110 Dual Fuel Lidded
Search Rangemaster UK
Show off your kitchen with ...
This is
#MyRangemaster
Simply snap and share a picture of your kitchen and tag
#MyRangemaster for the chance to win £200 of
Rangemaster cookware. If selected we will also send a
photographer round to professionally photograph you at
home with your range. You might even feature in some
of the UK’s top home interest titles!
To enter all you have to do is send in photos of your
Rangemaster kitchen and tell us in one sentence what
makes Rangemaster the heart of your kitchen? Entries
can be posted on our Facebook page, Instagram or Twitter
by tagging @RangemasterUK and using #MyRangemaster.
Or, if you prefer, simply send in your entry via e-mail to
[email protected]
Rangemaster will feature a number of entries on the
website online gallery and on the Rangemaster Facebook
page, and some kitchens may be selected to be
professionally photographed.
*
Terms & Conditions Apply
Our range cookers are well known for providing the best
possible cooking performance and years of faithful service.
However, a great cooker alone cannot guarantee perfect
results every time. The other vital ingredients are of course
enthusiasm and quality cookware.
We offer cookware to work perfectly with all fuel types
manufactured by Rangemaster, including induction hobs.
You can be assured of functionality with style, as well as the
quality and meticulous attention to detail you expect from
the pioneers of range cooking.
Visit www.rangemastercookshop.co.uk
Terms & Conditions
1. This is my Rangemaster is open to residents of UK mainland only, aged 18 years & over. 2. All entries should be submitted to the advertised e-mail address, or Rangemaster UK Facebook, Instagram or Twitter page
using the advertised hashtag & tag. 3. If we would like to professionally photograph your kitchen, you will be contacted via e-mail, Facebook / Twitter message or Instagram comment. 4. We cannot guarantee your
kitchen will be professionally photographed. 4. Any photographs received and professional photographs taken will belong to AGA Rangemaster plc with full usage rights. E&OE.
*
Contents
1. Before You Start...
1
6. Cleaning Your Cooker
16
Personal Safety 1
Essential Information
16
Electrical Connection Safety
2
Hotplate Burners
16
Gas Connection Safety
2
The Griddle
16
If You Smell Gas
2
Grill17
Peculiar Smells
2
Control Panel, Doors and Glass Lid
Ventilation3
Induction and Ceramic Care
3
Oven Care 4
Hob Care
17
Ovens17
7.Troubleshooting
19
5
8. Installation
21
Grill/Glide-out Grill™ Care
5
Dear Installer
21
Warming Zone Care
5
Safety Requirements and Regulations
21
Cooling Fan
5
Provision of Ventilation
21
Cooker Care
5
Location of Cooker
22
Cleaning5
2. Cooker Overview
Conversion22
6
Glass Lid
6
Hotplate Burners
7
Wok Burner (Classic & Toledo models)
7
The Wok Cradle (optional extra)
8
The Griddle
8
9
The Ovens
10
Operating the Ovens
10
Storage11
12
4.
14
Cooking Tips
Tips on Cooking with the Timer
14
General Oven Tips
14
5. Cooking Table
24
Fitting the Stability Bracket or Chain
24
Fitting the Handles and Handrail
(Classic only)
25
Gas Connection
26
Electrical Connection
27
Final Checks
27
Fitting the Plinth
27
Customer Care
27
9. Conversion to LP Gas
28
Injectors28
15
Tap Adjustment
28
Stick on Label
29
Pressure Testing
29
10. Circuit Diagram
11. Technical Data
Classic, Rangemaster & Toledo 110DF
25
Levelling25
11
3. The Clock
Moving the Cooker
Conversion to Another Gas
Accessories11
Main Oven Lights
23
Repositioning the Cooker Following
Connection25
Warmer9
The Grill
Positioning the Cooker
iii
30
31
Classic Lidded
31
Rangemaster Lidded
32
Toledo Lidded
33
U110099-07
iv
1. Before You Start...
Personal Safety
This User Guide covers a number of different models.
Although some of the illustrations will look different to
your particular model the functions will be the same. We
hope the meaning is clear.
This appliance is for cooking purposes only. It must not be
used for other purposes, for example heating a room. Using
it for any other purpose could invalidate any warranty or
liability claim. Besides invalidating claims this wastes fuel and
may overheat the control knobs.
Your cooker should give you many years of trouble-free
cooking if installed and operated correctly. It is important
that you read this section before you start.
This appliance is for use in Great Britain and the Republic
of Ireland. It is a Cat II2H3+ cooker and is set for G20 at
20 mbar. (A conversion kit for LPG is available for the
cooker.)
• This appliance can be used by children aged from
8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
• Children less than 8 years of age should be kept away
unless continuously supervised. Children shall not play
with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
• This appliance is designed for domestic cooking only.
Use for any other purpose could invalidate any warranty
or liability claim.
• The appliance and its accessible parts become hot
during use and will retain heat even after you have
stopped cooking. Care should be taken to avoid
touching heating elements.
• A long term cooking process has to be supervised from
time to time. A short term cooking process has to be
supervised continuously.
• At the risk of fire DO NOT store items on the cooking
surfaces.
• To avoid overheating, DO NOT install the cooker behind
a decorative door.
• Accessible parts will become hot during use and will
retain heat even after you have stopped cooking. Keep
babies and children away from the cooker and never
wear loose-fitting or hanging clothes when using the
appliance.
• DO NOT use a steam cleaner on your cooker.
• Always keep combustible materials, e.g. curtains, and
flammable liquids a safe distance away from the cooker.
• DO NOT spray aerosols in the vicinity of the cooker
while it is on.
1
Electrical Connection Safety
Gas Connection Safety
A Gas Safe registered engineer should service the cooker
and only approved spare parts should be used.
• This cooker is a Class 2 Subclass 1 appliance.
• This appliance can be converted for use on another gas.
• Before installation, make sure that the cooker is suitable
for your gas type and supply voltage. See the data
badge.
• DO NOT use reconditioned or unauthorised gas
controls.
• Disconnect from the electricity and gas supply before
servicing.
• When servicing or replacing gas-carrying components
disconnect from the gas supply before starting
operation. Check the appliance is gas sound after
completion.
• Make sure that the gas supply is turned on and that the
cooker is wired in and switched on.
• In your own interest and that of safety, it is law that all
gas appliances be installed by a qualified person(s).
• An appliance for use on LPG must not be installed in
a room or internal space below ground level, e.g. in a
basement.
• This cooker must be installed in accordance with:
• British Standards/Codes of Practice, BS 5440 Part 2
• Natural Gas: BS 6172 and BS 6891
• LP Gas: BS 5482-1 (when the installation is in a
permanent dwelling)
• Gas Safety (Installation and Use) regulations
• Relevant Building/IET regulations
The electrical installation must be installed in accordance
with all relevant British Standards/Codes of Practice,
BS 7671. Or with the relevant national and local
regulations and with the local gas and electricity supply
companies’ requirements.
Otherwise, all installations must be in accordance with
the relevant instructions in this booklet.
Read the instructions before installing or using this appliance.
• This appliance is heavy so take care when moving it.
• The cooker may be installed in a kitchen/kitchen diner
but NOT in a room containing a bath or shower.
• This cooker must be earthed.
• This cooker MUST NOT be connected to an ordinary
domestic power point.
• It is normal for the hob control display to flash for about
2 seconds during first power setting.
• Set the clock to make sure that the oven is functional –
see the relevant section in this manual.
• The appliance must be installed in accordance with the
regulations in force and only in a well ventilated space.
• Failure to install the appliance correctly could invalidate
any warranty or liability claims and lead to prosecution.
• DO NOT install the appliance on a platform.
• DO NOT move the cooker while it is plugged into the
electricity supply.
• Before electrical reconnection, check that the appliance
is electrically safe.
If You Smell Gas
•
•
•
•
•
•
•
•
DO NOT turn electric switches on or off
DO NOT smoke
DO NOT use naked flames
Turn off the gas at the meter or cylinder
Open doors and windows to get rid of the gas
Keep people away from the area affected
Call your gas supplier
If you are using Natural Gas in the UK, ring the
National Grid on: 0800 111 999
Peculiar Smells
When you first use your cooker it may give off an odour. This
should stop after use.
Before using for the first time, make sure that all packing
materials have been removed and then, to dispel
manufacturing odours, turn the ovens to 200 °C and run for at
least an hour.
Before using the grill for the first time you should also turn on
the grill and run for 30 minutes with the grill pan in position,
pushed fully back and the grill door open.
Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.
2
Ventilation
• DO NOT use water on grease fires and never pick up
a flaming pan. Turn the controls off and then smother
a flaming pan on a surface unit by covering the pan
completely with a well fitting lid or baking tray. If
available, use a multi-purpose dry chemical or foamtype fire extinguisher.
• DO NOT modify this appliance. This appliance is not
intended to be operated by means of external timer or
separated remote-control system.
• Flammable materials may explode and result in fire or
property damage.
The use of a cooking appliance results in the production
of heat and moisture in the room in which it is installed.
Therefore, make sure that the kitchen is well ventilated:
keep natural ventilation holes open or install a powered
cookerhood that vents outside. If you have several hotplates/
burners on, or use the cooker for a long time, open a window
or turn on an extractor fan
Maintenance
• It is recommended that this appliance is serviced
annually.
• DO NOT use cooking vessels on the hotplate that
overlap the edges.
• Unless specified otherwise in this guide, always allow
the cooker to cool and then switch it off at the mains
before cleaning or carrying out any maintenance work.
• DO NOT attempt to disassemble or clean around any
burner while another burner is on, otherwise an electric
shock could result.
• NEVER operate the cooker with wet hands.
• DO NOT use a towel or other bulky cloth in place of a
glove – it might catch fire if brought into contact with a
hot surface.
• DO NOT use hotplate protectors, foil or hotplate covers
of any description. These may affect the safe use of
your hotplate burners and are potentially hazardous to
health.
• NEVER heat unopened food containers. Pressure build
up may make the containers burst and cause injury.
• DO NOT use unstable saucepans. Always make sure that
you position the handles away from the edge of the
hotplate.
• NEVER leave the hotplate unattended at high heat
settings. Pans boiling over can cause smoking,
and greasy spills may catch on fire. Use a deep fat
thermometer whenever possible to prevent fat
overheating beyond the smoking point.
• Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
• NEVER leave a chip pan unattended. Always heat fat
slowly, and watch as it heats. Deep fry pans should be
only one third full of fat.
• NEVER try to move a pan of hot fat, especially a deep
fat fryer. Wait until the fat is cool. Filling the pan too full
of fat can cause spill over when food is added. If you use
a combination of oils or fats in frying, stir them together
before heating, or as the fats melt.
• Foods for frying should be as dry as possible. Frost on
frozen foods or moisture on fresh foods can cause hot
fat to bubble up and over the sides of the pan. Carefully
watch for spills or overheating of foods when frying at
high or medium high temperatures.
• DO NOT use the top of the flue (the slot along the back
of the cooker) for warming plates, dishes, drying tea
towels or softening butter.
Induction and Ceramic Care
• Important information for pacemaker and
implanted insulin pump users: The functions of this
hob comply with the applicable European standards
on electromagnetic interference. If you are fitted
with a pacemaker or implanted insulin pump and are
concerned please consult your doctor for medical
advice.
• When the hob is in use keep magnetic items away, such
as credit and debit cards, floppy disk, calculators, etc.
• Take care when touching the marked cooking areas of
the hob.
• Use adequately sized pans with flat bottoms that are
large enough to cover the surface of the hotplate
heating area. Using undersized pans will expose a
portion of the hotplate surface to direct contact and
may result in the ignition of clothing
• Only certain types of glass, glass-ceramic, earthenware
or other glazed containers are suitable for use on the
warming zone; others may break because of the sudden
change in temperature.
• Only certain types stainless steel, enamelled steel pans
or cast iron pans with enamelled bases are suitable for
induction hob cooking.
• Only certain types of glass, glass-ceramic, earthenware
or other glazed containers are suitable for hotplate
cooking; others may break because of the sudden
change in temperature. NEVER cook directly on the hob
surface (Fig. 1.1).
• Take care NOT to scratch the surface when placing
cookware on the glass panel.
• DO NOT leave the hob zones switched on unless being
used for cooking.
• DO NOT stand or rest heavy objects on the hob.
Although the ceramic surface is very strong, a sharp
blow or sharp falling object (e.g. a salt cellar) might
cause the surface to crack or break (Fig. 1.2).
• Should a crack appear in the surface, disconnect the
appliance immediately from the supply and arrange for
its repair.
• Always LIFT pans off the hob. Sliding pans may cause
marks and scratches (Fig. 1.3).
3
• Take care when placing hot lids onto the hob surface.
Lids that have been covering boiling or steaming foods
can ‘stick’ to the ceramic glass. Should this occur, DO
NOT attempt to lift the lid off the hotplate: this may
damage the hob surface. Instead, carefully slide the lid
to the edge of the hob surface and remove.
• DO NOT place anything between the base of the pan
and the hob surface (e.g. asbestos mats, aluminium foil,
wok stand).
• Take care NOT to place metallic objects such as knives,
forks, spoons and lids on the hob surface since they can
get hot.
• We recommend that you avoid wiping any surface unit
areas until they have cooled and the indicator light
has gone off. Sugar spills are the exception to this (see
‘Cleaning your Cooker’). After cleaning, use a dry cloth
or paper towel to remove any cleaning cream residue.
• The ceramic surface should be washed after use in order
to prevent it from becoming scratched or dirty. Clean
the hob with caution as some cleaners can produce
noxious fumes if applied to a hot surface..
• DO NOT leave the hob unattended. Care should be
taken to not allow your cookware to boil dry. It will
damage your cookware and Induction Glass Hob.
• After use, switch off the hob element by its control. DO
NOT rely on the pan detector.
ArtNo.312-0001 Not cooking surface
Fig. 1.1
Fig. 1.2
Fig. 1.3
Oven Care
• When the oven is not in use and before attempting
to clean the cooker always be certain that the control
knobs are in the OFF position.
• Use oven gloves to protect your hand from potential
burns.
• Cooking high moisture content foods can create a
‘steam burst’ when the oven door is opened (Fig. 1.4).
When opening the oven, stand well back and allow any
steam to disperse.
• The inside door face is constructed with toughened
safety glass. Take care NOT to scratch the surface when
cleaning the glass panel.
• Accidental damage may cause the door glass panel to
fracture.
• Keep oven vent ducts unobstructed.
• DO NOT use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
• Make sure the shelves are pushed firmly to the back
of the oven. DO NOT close the door against the oven
shelves.
• DO NOT use aluminium foil to cover shelves, linings or
the oven roof.
• When the oven is on, DO NOT leave the oven door open
for longer than necessary, otherwise the control knobs
may become very hot.
• DO NOT use the timed oven if the adjoining oven is
already warm.
ArtNo.312-0003 Moving pans
Fig. 1.4
ArtNo.324-0001 Steam burst
Fig. 1.5
ArtNo.090-0007 90 Ceramic:
oven steam out the back
4
Cleaning
• DO NOT place warm food in the oven to be timed.
• DO NOT use a timed oven that is already warm.
• Use dry oven gloves when applicable – using damp
gloves might result in steam burns when you touch a
hot surface.
• Isolate the electricity supply before carrying out any
thorough cleaning. Allow the cooker to cool.
• In the interests of hygiene and safety, the cooker should
be kept clean at all times as a build up in fats and other
food stuff could result in a fire.
• Clean only the parts listed in this guide.
• Clean with caution. If a wet sponge or cloth is used to
wipe spills on a hot surface, be careful to avoid steam
burns. Some cleaners can produce noxious fumes if
applied to a hot surface.
• NEVER use paint solvents, washing soda, caustic
cleaners, biological powders, bleach, chlorine based
bleach cleaners, coarse abrasives or salt.
• DO NOT mix different cleaning products – they may
react together with hazardous results.
• All parts of the cooker can be cleaned with hot soapy
water.
• Take care that no water seeps into the appliance.
• Before you remove any of the grill parts for cleaning,
make sure that they are cool or use oven gloves.
• DO NOT use any abrasive substances on the grill and
grill parts.
• DO NOT put the side runners in a dishwasher.
• DO NOT put the burner heads in a dishwasher.
• NEVER use caustic or abrasive cleaners as these will
damage the surface.
• DO NOT use steel wool, oven cleaning pads or any other
materials that will scratch the surface.
• NEVER store flammable materials in the drawer.
This includes paper, plastic and cloth items, such
as cookbooks, plastic ware and towels, as well as
flammable liquids.
• DO NOT store explosives, such as aerosol cans, on or
near the appliance.
• DO NOT use steel wool, oven cleaning pads, or any
other materials that will scratch the surface.
• DO NOT attempt to disassemble or clean around any
burner while another burner is on, otherwise an electric
shock could result.
Hob Care
• NEVER allow anyone to climb or stand on the hob.
• DO NOT use the hob surface as a cutting board.
• DO NOT leave utensils, foodstuffs or combustible items
on the hob when it is not in use (e.g. tea towels, frying
pans containing oil).
• DO NOT place plastic or aluminium foil, or plastic
containers on the hob.
• Always turn the control to the OFF position before
removing a pan.
• Avoid heating an empty pan. Doing so may damage
both the hob and pan.
Grill/Glide-out Grill™ Care
• When using the grill, make sure that the grill pan is
in position and pushed fully in, otherwise the control
knobs may become very hot.
• DO NOT leave the grill on for more than a few moments
without the grill pan underneath it, otherwise the knobs
may become hot.
• NEVER close the grill door when the grill is on.
• Accessible parts may be hot when the grill is in use.
Young children should be kept away.
Warming Zone Care
• NEVER attempt to cook on the warming zone.
• DO NOT use the warming zone as a cutting board.
• DO NOT leave the warming zone switched on unless
being used for warming.
• Avoid warming an empty pan. Doing so may damage
both the warming zone and pan.
Cooling Fan
This appliance may have a cooling fan. When the grill or oven
is in operation the fan will run to cool the fascia and control
knobs.
Cooker Care
As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth. This will also help to
prevent soiling and discolouration of the oven exterior by
cooking vapours (Fig. 1.5).
5
2. Cooker Overview
DocNo.020-0013 - Overview - 110DF - Classic, RM & Toledo lidded
Fig.2.1
A
B
O
O
C
O
D
F
E
G
ArtNo.212-0002 - 110 Classic ceramic front view
The 110 dual fuel cooker (Fig.2.1) has the following features:
Fig.2.2
A. Glass lid
B.
5 hotplate burners including a warmer and:
• A wok burner (Classic & Toledo models)
• A high burner (110 model)
C.
A control panel
D. A glide-out grill
E.
Main conventional oven
F.
Fan oven
G. Storage drawer
Glass Lid
This model has a glass lid over the hotplate. To open, simply
lift it at the front (Fig.2.2).
The glass lid has a safety device which cuts off the hotplate
burner gas supply if the lid is accidentally closed with a
burner on. DO NOT use this to turn the burners off. The gas
supply is restored when the lid is raised.
The toughened glass lid is not intended as a work
nn
surface and should not be used for this purpose. A
scratch could cause the glass to shatter.
6
Hotplate Burners
Fig.2.3
The drawing by each of the central knobs indicates which
burner that knob controls.
Each burner has an Flame Supervision Device (FSD) that
prevents the flow of gas if the flame goes out.
When the igniter button is pressed in, sparks will be
made at every burner – this is normal. Do not attempt to
disassemble or clean around any burner while another
burner is on, otherwise an electric shock could result.
To light a burner, press the igniter button, and push in and
turn the associated control knob counter-clockwise to the
high position as indicated by the large flame symbol (),
(Fig.2.3).
Fig.2.4
The igniter should spark and light the gas. Keep holding the
knob pressed in to let the gas through to the burner for about
ten seconds.
If, when you let go of the control knob, the burner goes out,
then the FSD has not been bypassed. Turn the control knob
to the OFF position and wait for one minute before you try
again, this time making sure to hold in the control knob for
slightly longer.
Fig.2.5
Adjust the flame height to suit by turning the control knob
clockwise (Fig.2.4).
Fig.2.6
If a burner flame goes out, turn off the control knob and
leave it for one minute before relighting it.
Make sure that the flames are under the pans. Using a lid will
help the contents boil more quickly (Fig.2.5).
ArtNo.311-0002 Pan with rim
Large pans should be spaced well apart.
ArtNo.311-0001 Right pans gas
Fig.2.7
Pans and kettles with concave bases or down-turned base
rims should not be used (Fig.2.6).
Fig.2.8
Art No. 311-0003 Simmer aids
Simmering aids, such as asbestos or mesh mats, are
NOT recommended (Fig.2.7). They will reduce burner
performance and could damage the pan supports.
You should also avoid using unstable and misshapen pans
that may tilt easily, and pans with a very small base diameter,
e.g. milk pans, single egg poachers (Fig.2.8).
ArtNo.311-0004 Tipping wok
The minimum recommended pan diameter is 120 mm. The
maximum allowable pan base diameter is 260 mm.
Fig.2.9
DO NOT use cooking vessels on the hotplate that overlap the
edges.
Wok Burner (Classic & Toledo models)
The wok burner is designed to provide even heat over a large
area. They are ideal for large pans and stir-frying (Fig.2.9).
For heating smaller pans, the aforementioned hotplate
burners may be more efficient.
ArtNo.311-0046 - Elan Wok burner
You can remove the burner parts for cleaning; see ‘Cleaning
your cooker’.
You should wipe the enamel top surface of the cooker around
the hotplate burners as soon as possible after spills occur. Try
to wipe them off while the enamel is still warm.
7
Note: The use of aluminium pans may cause metallic marking
of the pan supports. This does not affect the durability of the
enamel and may be cleaned off with an appropriate metal
cleaner.
Fig.2.10
The Wok Cradle (optional extra)
The wok cradle is designed to fit a Professional 35 cm wok. If
you use a different wok, make sure that it fits the cradle. Woks
vary very widely in size and shape. It is important that the
wok sits down on the pan support – however, if the wok is too
small, the cradle will not support it properly (Fig.2.10).
ArtNo.311-0006 Correct wok sizes
Fig.2.11
The cradle should be used on the wok burner only. When you
fit the cradle, check that it is supported properly on a pan
support and the wok is sitting level in the cradle (Fig.2.11).
The cradle will get very hot in use – allow plenty of time for it
to cool before you pick it up.
The Griddle
ArtNo.311-0007 Wok stand close-up
The griddle fits the left-hand pan support, front to back
(Fig.2.12). It is designed for cooking food on directly. DO NOT
use pans of any kind on it. The griddle surface is non-stick and
metal cooking utensils (e.g. spatulas) will damage the surface.
Use heat resistant plastic or wooden utensils.
Fig.2.12
DO NOT put it crossways – it will not fit properly and
nn
will be unstable (Fig.2.13).
DO NOT put it on any other burner – it is not
nn
designed to fit in any of the other pan supports.
0
0
0
0
O
0
O
O
0
0
0
9
9
S
S
8
1
5
3 4
2
Position the griddle over the hotplate burners resting on the
pan support. Check that it is securely located.
6
8
7
1
5
3 4
2
6
7
Fig.2.13
The griddle can be lightly brushed with cooking oil before
use (Fig.2.14). Light the hotplate burners. Adjust the flame
heights to suit.
Preheat the griddle for a maximum of 5 minutes before
adding food. Leaving it longer may cause damage. Turn the
control knobs towards the low position, marked with the
small flame symbol, to reduce the burner flames.
0
0
0
0
0
O
O
O
0
0
0
9
9
S
8
1
Always leave space around the griddle for the gases
nn
to escape.
ArtNo.311-0009 Oil on griddle
NEVER fit two griddles side by side (Fig.2.15).
nn
2
5
3 4
6
S
8
7
1
2
5
3 4
6
7
Fig.2.14
After cooking, allow the griddle to cool before cleaning.
Fig.2.15
ArtNo.311-0008 Griddle positioning
8
Warmer
Fig.2.16
On the right of the hob is the warmer (Fig.2.16). Use the
warmer for keeping food warm while the final touches are
put to a meal. Turn the control knob counter-clockwise to the
‘On’ position.
For best results, preheat a covered serving dish for 10 minutes
before adding food to it.
Use only heat resistant dishes.
The Grill
Open the door and pull the grill pan forward using the handle
(Fig.2.17).
Fig.2.17
The grill has two elements that allow either the whole area of
the pan to be heated or just the right-hand half.
Adjust the heat to suit by turning the control knob. To heat
the whole grill, turn the control knob clockwise (Fig.2.18).
ArtNo.330-0003 - Grill pan w handle pulled forwards
To heat the right-hand half, turn the control knob counterclockwise. The neon indicator light by the grill control will
come on.
For best results, slide the grill pan back into the grill chamber
and preheat the appropriate part(s) of the grill for two
minutes. The grill trivet can be removed and the food placed
on it while you are waiting for the grill to preheat.
Fig.2.18
Once the grill has preheated, slide the grill pan out again.
With the trivet back in place with the food on it, slide the grill
pan back into the grill chamber. Make sure that it is pushed
right in.
ArtNo.235-0007 - Classic
DL grill control
Accessible parts may be hot when the grill is in use.
nn
Young children should be kept away.
The grill trivet can be turned over to give two grilling
positions (Fig.2.19).
Do not leave the grill on for more than a few moments,
without the grill pan underneath it.
Fig.2.19
Never close the grill door when the grill is on.
nn
ArtNo.331-0002 Grill pan high/low position
9
The Ovens
Fig.2.20
The clock must be set to the time of day before the ovens
will work. See the following section on ‘The Clock’ for
instructions on setting the time of day.
References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed
from the front of the appliance.
ArtNo.235-0004 Classic DL oven 1
The left-hand oven is a conventional oven, while the righthand oven is a fan oven.
The Conventional Oven
The left-hand oven is a conventional oven and has two
heating elements – one visible in the top of the oven and the
other under the oven base.
Fig.2.21
Note: Be careful to avoid touching the top element and
element deflector when placing or removing items from the
oven.
The exposed top element may cook some foods too quickly,
so we recommend that the food be positioned in the lower
half of the oven to cook. The oven temperature may also need
to be lowered.
ArtNo.235-0005 - Classic
DL oven control 2
Similar items being cooked will need to be swapped around
for even cooking.
The Fan Oven
The right-hand oven is a fan oven that circulates hot air
continuously, which means faster, more even cooking.
The recommended cooking temperatures for a fan oven are
generally lower than a conventional oven.
Note: Please remember that all cookers vary so temperatures
in your new ovens may differ to those in your previous
cooker.
Operating the Ovens
Turn the oven knob to the desired temperature (Fig.2.20).
The oven indicator light will glow until the oven has reached
the temperature selected. It will then cycle on and off during
cooking (Fig.2.21).
10
Accessories
Fig.2.22
Oven Shelves
The oven shelves (Fig.2.22) can be easily removed and
refitted.
Shelf guard
Pull the shelf forward until the back of the shelf is stopped by
the shelf stop bumps in the oven sides (Fig.2.23).
Lift up the front of the shelf so the back of the shelf will pass
under the shelf stop and then pull the shelf forward
(Fig.2.24).
To refit the shelf, line up the shelf with a groove in the oven
side and push the shelf back until the ends hit the shelf stop.
Lift up the front so the shelf ends clear the shelf stops, and
then lower the front so that the shelf is level and push it fully
back (Fig.2.25).
Front
The Handyrack (Main Oven)
Fig.2.23
The Handyrack (Fig.2.26) fits to the left-hand oven door
only. Food cooking on it is easy to attend to, because it is
accessible when the door is open.
Fig.2.24
ArtNo.320-0011 Removing the shelf 1
The maximum weight that can be held by the Handyrack
is 5.5 kg (12 lb). It should only be used with the supplied
roasting tin, which is designed to fit the Handyrack. Any other
vessel could be unstable.
ArtNo.320-0012 Removing the shelf 2
Fig.2.25
It can be fitted at two different heights. One of the oven
shelves must be removed and the other positioned to suit.
Fig.2.26
When the Handyrack is used in its highest position, other
dishes can be cooked on the bottom shelf position or base of
the oven.
When the Handyrack is used in its lowest position, other
dishes can be cooked on the second shelf position or base of
the oven.
ArtNo.320-0014 Handyrack on LH door
ArtNo.320-0013 Removing the shelf 3
Fig.2.27
Fig.2.28
To fit the Handyrack, locate one side of it on the door bracket
(Fig.2.27).
Then spring the other side out to clip it onto the other
bracket (Fig.2.28).
Main Oven Lights
Press the appropriate button to turn the light on (Fig.2.29).
ArtNo.320-0015
Fitting the Handyack 1
If the oven light fails, turn off the power supply before
changing the bulb. See the ‘Troubleshooting’ section for
details on how to change the bulb.
ArtNo.320-0016
Fitting the handyrack 2
Storage
Fig.2.29
The bottom drawer is for storing oven trays and other
cooking utensils. It can get very warm, so do not store
anything in it that may melt or catch fire.
ArtNo.320-0027
- Twin oven lights
The drawer can be removed completely by pulling it right out
and up.
11
3. The Clock
You can use the timer (Fig. 3.1) to turn the oven(s) on and off.
The clock must be set to the time of day before the oven(s)
will work.
Fig. 3.1
Table 3.1 describes the symbols shown on the digital display.
ArtNo.302-0002 - 6BC annotated
Setting the Time of Day
A
When the cooker is first connected to the mains, or if there
has been a prolonged power interruption, the clock display
flashes [ 0.00 ] and [AUTO].
B
C
D
E
F
During the time setting process the centre dot will flash.
When the process is complete the dot will stop flashing and
the [] symbol will be displayed.
A – Minute minder, B – ‘Cook’ time, C – ‘Stop’ time, D – Manual,
E & F – Time setting buttons
Symbol
Function
Notes
[]
Minute Minder is active
The time of day can be set in two ways:
• Press and hold the [] button. Now press the [+] or [-]
buttons to increase or decrease the time (Fig. 3.2). Holding
the [+] or [-] buttons for more than 2 seconds will advance
/ decrease the set time quickly. Release the buttons to set
the time of day.
• Press and hold both the [] and [] buttons down
(Fig. 3.3). Now press the [+] button (or [–] button) until the
correct time shows.
Do not forget that it is a 24-hour clock.
If the ‘cook’ [] symbol is not
displayed the program has either:
[]
Oven(s) can be operated
[AUTO]
Oven(s) are being
controlled in
semi-automatic or
automatic mode
[P]
Self clean (pyrolytic)
mode has been enabled
[dot]
Flashes during setting
the time of day
• ended and the oven(s) are nonoperational
• the oven(s) are being controlled
by an automatic program that
has not started
If you need to reset the clock/cooker, turn off the power and
wait several minutes, then start again.
Automatic Dimming
Providing there are no automatic programs set, and the
minute minder is not active, your clock will automatically dim
during the hours between 22:00 and 06:00.
Minute Minder
Press and hold the [] button (Fig. 3.4), and then press the
[+] button (or [–] button) until the length of time you want to
cook for is shown (Fig. 3.5).
Your cooker may not have this
pyrolytic function
Table 3.1
Fig. 3.2
Fig. 3.3
You can check the time remaining by pressing []. When the
beeper sounds cancel it by pressing any button.
ArtNo.302-0002 - 6BC annotated
Fig. 3.4
ArtNo.302-0002 - 6BC annotated
ArtNo.302-0002 - 6BC annotated
To reset the minute minder time; simultaneously press the [+]
and [-] buttons.
Note: this will clear all automatic programs.
Fig. 3.5
ArtNo.302-0002 - 6BC annotated
•
The ‘cook period’, which is the length of time you
want the oven to cook for.
•
The ‘stop time’, which is the time of day you want the
oven to stop cooking.
Setting a Cook Duration
Press and hold the [] button and set the required ‘cook
period’ by pressing the [+] button (or [–] button) (Fig. 3.6). The
clock will now control the cook period of your oven(s). The
[] symbol and [AUTO] will be displayed.
Fig. 3.6
Once the ‘cook period’ is reached, the beeper sounds and the
[AUTO] symbol flashes. Turn the oven control knob to 0 and
then press any button to stop the beep. Press [] to return to
manual cooking.
ArtNo.302-0002 - 6BC annotated
12
Setting a Cook End Time
Press and hold the ‘stop time’ [] button (Fig. 3.7) and then
press the [+] button (or [–] button) until the required ‘stop
time’ shows (Fig. 3.8). The [] symbol and [AUTO] will show
in the display.
Fig. 3.7
Once the ‘stop time’ is reached, the beeper sounds and the
[AUTO] symbol flashes. Turn the oven control knob to 0 and
then press any button to stop the beep. Press [] to return to
manual cooking.
To Start and Stop the Ovens Automatically
Before you set the clock for automatic operation you must
have two numbers clearly in mind – the ‘cook period’ and the
‘stop time’.
Fig. 3.8
ArtNo.302-0002 - 6BC annotated
ArtNo.302-0002 - 6BC annotated
Fig. 3.9
Note: You cannot set a start time directly – this is set
automatically by setting the ‘cook period’ and the ‘stop time’.
Fig. 3.10
ArtNo.302-0002 - 6BC annotated
Press and hold the [] button (Fig. 3.9) and then press the
[+] button (or [–] button) until the required ‘cook period’ shows
(Fig. 3.10).
ArtNo.302-0002 - 6BC annotated
Fig. 3.11
Fig. 3.12
Now press and hold the [] button (Fig. 3.11) and then press
the [+] button (or [–] button) until the required ‘stop time’
shows (Fig. 3.12). Release the buttons.
ArtNo.302-0002 - 6BC annotated
ArtNo.302-0002 - 6BC annotated
[AUTO] will now show in the display (Fig. 3.13).
Set the oven(s) to the required temperature. When cooking
is finished [AUTO] will flash and the beeper will sound. Turn
the oven knob(s) to the OFF position first, and then press any
button once to stop the beep; press the [] button to return
to manual cooking.
Fig. 3.13
If you are out, do not worry about the beeper going off, it
stops after a while. When you return, turn the oven knob(s) to
0 first, and then press [] to return to manual cooking.
AUTO is Showing, You Want to Reset to Manual Cooking
To return to manual cooking mode from an Automatic
setting, simultaneously press the [+] and [-] key, this will clear
the automatic program and return to manual mode.
Fig. 3.14
ArtNo.302-0002 - 6BC annotated
Please note that this action will also clear the [Minute Minder]
setting.
Beeper Tone Adjustment.
The beeper tone can be adjusted to three different levels.
ArtNo.302-0002 - 6BC annotated
Symbol
Function
Notes
[]
Sets the Minute Minder
Used with the [+] and [-] buttons
[]
Sets the duration / cook
period
Used with the [+] and [-] buttons
[]
Sets the end / stop cook
time
Used with the [+] and [-] buttons
[ ]
Allows the time of day to
be set when ‘AUTO’ is not Used with the [+] and [-] buttons
or
active
[] & []
Whilst in the time of day mode, press and hold the [-] button
for a period until the display shows the Tone Bars (Fig. 3.14).
Release the [-] button and immediately press again, this will
adjust the tone down by a bar. Continue the process until a
comfortable, tone is reached.
[ ]
Resets the cooking
control to manual
Please note, during a power reset the clock will remember the
last tone set.
[ - ]
Decreases time interval
Holding this button down
allows a quick set
For an overview of the functions refer to Table 3.2.
[ + ]
Increases time interval
Holding this button down
allows a quick set
[ + ] & [ - ]
Clears all ‘AUTO’ and
minute minder programs
Table 3.2
13
4. Cooking Tips
Tips on Cooking with the Timer
General Oven Tips
If you want to cook more than one dish, choose dishes that
require approximately the same cooking time. However,
dishes can be ‘slowed down’ slightly by using small containers
and covering them with aluminium foil, or ‘speeded up’
slightly by cooking smaller quantities or placing them in
larger containers.
The wire shelves should always be pushed firmly to the back
of the oven.
Baking trays with food cooking on them should be placed
level with the front edge of the oven’s wire shelves. Other
containers should be placed centrally. Keep all trays and
containers away from the back of the oven, as overbrowning
of the food may occur.
Very perishable foods such as pork or fish should be avoided
if a long delay period is planned, especially in hot weather.
For even browning, the maximum recommended size of a
baking tray is 340 mm (13½”) by 340 mm (13½”).
DO NOT place warm food in the oven to be timed.
nn
DO NOT use a timed oven that is already warm.
nn
DO NOT use the timed oven if the adjoining oven is
nn
already warm.
When the oven is on, do not leave the door open for
longer than necessary, otherwise the knobs may get very
hot.
• Always leave a “finger’s width” between dishes on the same
shelf. This allows the heat to circulate freely around them.
• To reduce fat splashing when you add vegetables to hot fat
around a roast, dry them thoroughly or brush lightly with
cooking oil.
• Where dishes may boil and spill over during cooking, place
them on a baking tray.
• The ‘Cook & Clean’ oven liners (see ‘Cleaning Your Cooker’)
work better when fat splashes are avoided. Cover meat
when cooking.
• Sufficient heat rises out of the oven while cooking to warm
plates in the grill compartment.
• If you want to brown the base of a pastry dish, preheat the
baking tray for 15 minutes before placing the dish in the
centre of the tray.
Whole poultry must be thoroughly defrosted before being
placed in the oven. Check that meat and poultry are fully
cooked before serving.
14
5. Cooking Table
DocNo.031-0004 - Cooking table - electric & fan single cavity
The oven control settings and cooking times given in the table below are intended to be used
AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a
preferred result.
Food is cooked at lower temperature in a fan oven than in a conventional oven. When using
recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The
temperature in the fan oven does not vary with height in the oven so you can use any shelf.
Top (T)
Centre (C)
Base (B)
Oven Shelf Positions
Conventional Oven
Fan Oven
Temperature °C
Temperature
(Shelf Position)
°C
160 (C)
150
200 (C)
190
160 (C)
150
200 (C)
190
160 (C)
150
200 (C)
190
160 (C)
150
20-25 minutes per 500g +20-25 minutes.
200 (C)
190
15-20 minutes per 500g +15-20 minutes.
160 (C)
150
20 minutes per 500g +20 minutes.
200 (C)
190
15 minutes per 500g +15 minutes.
160 (C)
150
25-30 minutes per 500g.
200 (C)
190
20 minutes per 500g.
140-150 (C)
130-140
220 (C)
210
Large tins 30-35 minutes; individual 10-20 minutes.
140 (C/B)
130
45-50 minutes per 500g of mixture.
Fruit 180 mm tin
150 (C/B)
140
2-2½ hours.
Fruit 230 mm tin
150 (C/B)
140
Up to 3½ hours.
Madeira 180 mm
160 (C/B)
150
80-90 minutes.
Small cakes
170 (C/B)
160
15-25 minutes.
Scones
200 (C/B)
190
10-15 minutes.
180 mm tin
170 (C/B)
160
20-30 minutes.
210 mm tin
170 (C/B)
160
30-40 minutes.
Shortcrust tarts
200 (C/B)
190
20-30 minutes on a preheated tray.
Fruit pies
180 (C/B)
170
35-45 minutes.
Tartlets
180 (C/B)
170
10-20 minutes according to size.
Puff pastry
210 (C/B)
200
20-40 minutes according to size.
Meringues
100 (C/B)
90
2-3 hours.
Food
Meat
ArtNo.050-0007
Oven shelf positions
T - Top; C - Centre; B - Base
Approximate Cooking Time
ArtNo.050-0001 Gas cooking table
Beef (no bone)
Lamb
Pork
Poultry
Chicken
Turkey
Duck
Casserole
Yorkshire Pudding
30-35 minutes per 500g +30-35 minutes. Thoroughly thaw frozen joints before
cooking. Meat may be roasted at
20-25 minutes per 500g +20-25 minutes.
220°C (210°C for fan oven) and the
30-35 minutes per 500g +30-35 minutes. cooking time adjusted accordingly.
25-30 minutes per 500g +25-30 minutes. For stuffed and rolled meats, add
approximately 10 minutes per 500g,
35-40 minutes per 500g +35-40 minutes. or cook at 200°C (190°C) for 20
25-30 minutes per 500g +25-30 minutes. minutes then 160°C (150°C) for the
remainder.
2-4 hours according to recipe.
For stuffed poultry, you could cook
at 200°C (190°C) for 20 minutes
then 160°C (150°C) for remainder.
Do not forget to include the weight
of the stuffing.
For fresh or frozen prepacked
poultry, follow instructions on the
pack. Thoroughly thaw frozen
poultry before cooking.
Cake
Very rich fruit - Christmas,
wedding, etc.
Using the conventional oven: when
two tier cooking leave at least one
runner space between shelves.
Position the baking tray with the
front edge along the front of the
oven shelf.
Victoria sandwich
Desserts
Baked egg custard
160 (C/B)
150
45-60 minutes.
Baked sponge pudding
180 (C/B)
170
40-45 minutes.
140-150 (C/B)
130-140
210 (C)
200
20-30 minutes.
Milk pudding
Bread
Fish
2 to 3 hours.
Fanned Grilling
Fillet
190 (C/B)
190 (C/B)
15-20 minutes.
Whole
190 (C/B)
190 (C/B)
15-20 minutes per 500g.
Steak
190 (C/B)
190 (C/B)
Steaks according to thickness.
15
Up to three tiers can be cooked in a
fan oven at the same time but make
sure to leave at least one runner
space between each shelf being
cooked on.
Using the conventional oven: for
even browning the maximum size of
baking tray recommended is 340 mm
x 340 mm. This ensures free heat
circulation.
If cooking a two tier load, the trays
should be interchanged
approximately halfway though the
cooking time.
6. Cleaning Your Cooker
Essential Information
Fig.6.1
A
Isolate the electricity supply before carrying out any
thorough cleaning. Allow the cooker to cool.
C
NEVER use paint solvents, washing soda, caustic
nn
cleaners, biological powders, bleach, chlorine based
B
bleach cleaners, coarse abrasives or salt.
DO NOT mix different cleaning products – they may
nn
react together with hazardous results.
E
D
All parts of the cooker can be cleaned with hot soapy water
– but take care that no surplus water seeps into the
appliance.
ArtNo.311-0032 Burner layout FSD
A – Cap, B – Head, C – Notch, D – Base , E – Electrode
Remember to switch on the electricity supply and reset the
clock before re-using the cooker.
A
Hotplate Burners
Fig.6.2
The burner heads and caps can be removed for cleaning.
B
DO NOT put the burner heads in a dishwasher.
nn
Make sure they are absolutely dry before replacing them.
C
The Single Ring Burners
When refitting the burner head, make sure that the notch
lines up with the electrode or hole in the base. Check that the
burner head is level and that the cap is fitted centrally on the
burner head (Fig.6.1).
D
ArtNo.311-0033 Wok burner details FSD
The Wok Burner
When reassembling the wok burner (Fig.6.2), turn over the
large base ring and find the ‘D’ shaped area (Fig.6.3). Turn the
head until the ‘D’ matches the one on the burner base. Flip
the burner over once again and place it on the burner base.
E
A – Inner burner cap, B – Outer burner cap, C – Inner burner head,
D – Outer burner head, E – Wok burner base
To fit the small inner burner, find the larger electrode notch in
the burner rim. Line this up with the white ignition electrode
and place the inner burner on the large base ring (Fig.6.4).
Fig.6.3
Now fit the two burner caps, making sure that they are seated
properly.
Check the burner ports are not blocked. If a blockage occurs,
remove stubborn particles using a piece of fuse wire.
The Wok Cradle
Recommended cleaning materials are hot soapy water, a
moistened soap pad, cream cleaner or a nylon scourer.
B
The Griddle
Always clean the griddle after use. Allow it to cool completely
before removing. Immerse the griddle plate in hot soapy
water. Use a soft cloth or, for stubborn stains, a nylon washing
up brush.
Note: If the griddle is washed in a dishwasher then some
dishwasher residue may appear on the back. This is normal
and will not affect the performance of your griddle.
A
ArtNo.311-0016 Fitting the burner inner head
A – Electrode notch, B – Ignition electrode
16
Fig.6.4
Grill
Fig.6.5
The grill pan and trivet should be washed in hot soapy water.
Alternatively, the grill pan can be washed in a dishwasher.
After grilling meats or any foods that soil, leave to soak for a
few minutes immediately after use. Stubborn particles may
be removed from the trivet using a nylon brush.
Before you remove any of the grill parts for cleaning,

make sure that they are cool, or use oven gloves.
DO NOT use any abrasive substances.
nn
ArtNo.320-0002a Proplus oven door side screws
Control Panel, Doors and Glass Lid
Fig.6.6
Avoid using any abrasive cleaners including cream cleaners.
For best results, use a liquid detergent.
The same cleaner can be used on the doors, or alternatively,
using a soft cloth wrung out in clean hot soapy water – but
take care that no surplus water seeps into the appliance. After
cleaning, polish with a dry cloth.
DO NOT use harsh abrasive cleaners or sharp metal
nn
scrapers to clean the glass lid since they can scratch
the surface, which may result in shattering of the
glass.
Glass Fronted Door Panels
The oven door front panels can be taken off so that the glass
panels can be cleaned. Move the cooker forward to gain
access to the sides (see the ‘Moving the Cooker’ section under
‘Installation’).
Open the oven door slightly and remove the front panel
fixing screws from the door sides, two each side (Fig.6.5).
Carefully lift off the outer door panel. The inside face of the
glass panels can now be cleaned – take care not to disturb or
wet the door insulation.
Note: If the door is triple glazed then the inner two panels are
fixed together and should not be separated.
After cleaning, carefully refit the outer door panel and replace
the side fixing screws.
DO NOT use harsh abrasive cleaners or sharp metal

scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Ovens
‘Cook & Clean’ Panels
The ovens have panels which have been coated with a special
enamel that partly cleans itself. This does not stop all marks
on the lining, but helps to reduce the amount of manual
cleaning needed. The ‘Cook & Clean’ panels work better
above 200 °C. If you do most of your cooking below this
temperature, occasionally remove the panels and wipe with a
lint free cloth and hot soapy water. The panels should then be
dried and replaced and the oven heated at 200 °C for about
one hour. This will make sure the ‘Cook & Clean’ panels are
working effectively.
17
DO NOT use steel wool, oven cleaning pads, or any
nn
other materials that will scratch the surface.
Cleaning Table
Cleaners listed (Table 5-1) are available from supermarkets or
electrical retailers as stated.
Removing the Main Oven Linings
Some of the lining panels can be removed for cleaning.
For enamelled surfaces use a cleaner that is approved for use
on vitreous enamel.
If you wish to clean the enamel interior of the oven, you
will need to remove the shelves before removing the ‘Cook
& Clean’ panels. You do not have to remove the support
brackets to remove the panels. Lift each panel upward and
slide forward off the support brackets (Fig.6.6).
Regular cleaning is recommended. For easier cleaning, wipe
up any spillages immediately.
Once the panels have been removed, the oven enamel
interior can be cleaned. Refit in the reverse order.
Hotplate
Part
Finish
Recommended Cleaning Method
Hob top (including burner heads and Enamel, stainless steel,
caps)
aluminium
Hot soapy water, soft cloth. Any stubborn stains remove gently
with a nylon scourer.
Ceramic/induction hob
Toughened glass
Hot soapy water; cream cleaner/scourer if necessary.
Griddle plate (some models only)
Non-stick surface
Allow to cool. Wash in hot soapy water. Do not use abrasive
cleaners/scourers. Dishwasher.
Warming zone (some models only) Toughened glass
Hot soapy water, cream cleaner/scourer if necessary.
Outside of Cooker
Part
Finish
Recommended Cleaning Method
Enamel or paint
Hot soapy water, soft cloth.
Any stubborn stains, remove gently with a liquid detergent.
Stainless steel
E-cloth (electrical retailers) or microfibre all-purpose cloth
(supermarket).
Sides and plinth
Painted surface
Hot soapy water, soft cloth.
Splashback/rear grille
Enamel or stainless steel
Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.
Control panel
Paint, enamel or stainless steel
Warm soapy water. Do not use abrasive cleaners on lettering.
Control knobs/handles & trims
Plastic/chrome, copper or
lacquered brass
Warm soapy water, soft cloth.
Brass
Brass polish.
Toughened glass
Hot soapy water, cream cleaner/scourer if necessary.
Finish
Recommended Cleaning Method
Sides, floor & roof of oven NOT
‘COOK & CLEAN’ OVEN PANELS
(see below)
Enamel
Any proprietary oven cleaner that is suitable for enamel.
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW
MANUFACTURER’S INSTRUCTIONS.
Do not allow contact with the oven elements.
‘Cook & Clean’ oven panels (some
models only)
Special enamel that partly
cleans itself
This surface cleans itself at 200 °C and above, or the panels can be
removed and washed with hot soapy water and a nylon brush.
Oven shelves, Handyrack, grill
trivet, Handygrill rack (some
models only)
Chrome
An oven interior cleaner that is suitable for chrome. Soap filled
pad. Dishwasher.
Grill pan/meat tin (some models
only)
Enamel
Hot soapy water. Soap filled pad. Dishwasher.
Door, door surround and storage
drawer exterior
Oven door glass/glass lid
Oven and Grill
Part
Table 5-1
18
7.Troubleshooting
Food is cooking too slowly, too quickly, or burning
Cooking times may differ from your previous oven.
Hotplate/Cooktop ignition or hotplate burners faulty
Is the power on? Is the clock illuminated?
Check that you are using the recommended
temperatures and shelf positions – see the oven
cooking guide. The oven control settings and cooking
times are intended to be used only as a guide.
If not, there maybe something wrong with the power
supply.
Are the sparker (ignition electrode) or burner slots
blocked by debris?
Individual tastes may require the temperature to be
altered either way, to get the results you want.
Are the burner trim and caps correctly located? See the
section on ‘Cleaning’.
The oven is not cooking evenly
Do not use a baking tray with dimensions larger than
those specified in the section on ‘General Oven Tips’.
Hotplate/Cooktop burners will not light
Make sure that the burner parts have been replaced
correctly after wiping or removing for cleaning.
If you are cooking a large item, be prepared to turn it
round during cooking.
Check that there is not a problem with your gas
supply. You can do this by making sure that other gas
appliances you may have are working.
If two shelves are used, check that space has been left
for the heat to circulate. When a baking tray is put into
the oven, make sure that it is placed centrally on the
shelf.
Do the burners spark when you push the button?
If not, verify that the power is on by checking that the
clock is illuminated.
Check that the door seal is not damaged and that the
door catch is adjusted so that the door is held firmly
against the seal.
Steam is coming from the oven
When cooking foods with high water content (e.g. oven
fries) there may be some steam visible at the rear grille.
A dish of water when placed on the shelf should be the
same depth all over. (For example, if it is deeper at the
back, then the back of the cooker should be raised up or
the front lowered.) If the cooker is not level, arrange for
your supplier to level it for you.
Take care when opening the oven door, as there may
be a momentary puff of steam when the oven door
is opened. Stand well back and allow any steam to
disperse.
Oven not coming on
Is the power on? Is the clock illuminated? If not, there
may be something wrong with the power supply.
What cleaning materials are recommended for the
cooker?
See the ‘Cleaning’ section for recommended cleaning
materials.
Is the cooker supply on at the isolator switch?
Has the time of day been set?
Never use caustic or abrasive cleaners as these will
nn
damage the surface.
Is the key symbol [] showing in the display to signify
that the oven is locked? See the ‘Clock’ section of the
instructions for more information on the ‘key lock’
feature.
An oven fan is noisy
The note of the oven fan may change as the oven heats
up – this is perfectly normal.
The timed oven is not coming on when automatic cooking
Has the oven knob been left in the OFF position by
mistake?
If there is an installation problem and I don’t get my
original installer to come back to fix it who pays?
You do. Service organizations will charge for their call
outs if they are correcting work carried out by your
original installer. It is in your interest to track down your
original installer.
Is the word ‘AUTO’ showing in the display? See the
‘Clock’ section of the instructions for more information.
Oven temperature getting hotter as the cooker gets older
If turning the temperature down using the oven control
knob has not worked, or has only worked for a short
time, then you may need a new thermostat. This should
be fitted by a qualified service person.
Power failure
In the event of a failure in the electrical supply,
remember to reset the clock to make sure that the
timed oven continues to operate.
19
Fig. 7.1
ArtNo.324-0005 Oven light bulb
Oven light is not working
The bulb has probably burnt out. You can buy a
replacement bulb (which is not covered under the
warranty) from a good electrical shop. Ask for a 15 W –
230 V lamp, FOR OVENS. It must be a special bulb, heat
resistant to 300 °C (Fig. 7.1).
Turn off the power at the circuit breaker.
Before removing the existing bulb, turn off the power
supply and make sure that the oven is cool. Open the
oven door and remove the oven shelves.
Fig. 7.2
Unscrew the bulb cover by turning counter-clockwise. It
may be very stiff (Fig. 7.2).
Taking care to protect your fingers with a glove in case
the bulb should shatter, unscrew the old bulb.
Screw in the new bulb; screw back the bulb cover. Turn
on the circuit breaker and check that the bulb now
lights.
The oven door is misaligned
The bottom hinge of either oven door can be adjusted
to alter the angle of the door (Fig. 7.3). Loosen the
bottom hinge fixing screws and use the notch and a flat
bladed screwdriver to move the position of the hinge to
set the hinge position (Fig. 7.4).
Fig. 7.3
Retighten the hinge screws.
Grill
Effect of hinge adjustment – exaggerated for clarity
Fig. 7.4
Centre line of hinge pin
ArtNo.320-0007 Oven door hinge adjustment 2
Oven door omitted for clarity
The fascia gets hot when I use the oven or grill
The cooker is cooled by a fan. If the fascia becomes
excessively hot when the cooker is in use then the
cooling fan may have failed. Should this occur please
contact your installer, a qualified repair engineer or
Customer Service to arrange for its repair.
The knobs get hot when I use the oven or the grill. Can I
avoid this?
Yes, this is caused by heat rising from the oven or the
grill, and heating them up. Do not leave the oven door
open.
Make sure that the grill pan is pushed right back to the
‘back stop’ when grilling.
Always grill with the grill compartment door open.
Grill is not cooking properly
Are you using the pan and trivet supplied with the
cooker?
Is the pan being used on the runners, not the floor of the
grill compartment?
Is the grill tray pushed back fully to the stop?
20
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
8. Installation
Dear Installer
In the UK:
Before you start your installation, please complete the details
below, so that, if your customer has a problem relating to
your installation, they will be able to contact you easily.
The regulations and standards are as follows:
In your own interest and that of safety, it is law that all
gas appliances be installed by competent persons. Gas
Safe registered installers undertake to work to safe and
satisfactory standards.
Installer’s Name
The cooker must be installed in accordance with:
•
Installer’s Company
•
•
ArtNo.050-0011 - Installer information table
Installer’s Telephone Number
•
•
Appliance Serial Number
All relevant British Standards / Codes of Practice, in
particular BS 5440 Part 2.
For Natural Gas – BS 6172 and BS 6891.
For LP Gas – BS 5482-1, (when the installation is
in a permanent dwelling), BS 5482-2, (when the
installation is in a caravan or other non-permanent
dwelling), or BS 5482-3, (when the installation is in a
boat).
The Gas Safety (Installation and Use) regulations.
The relevant Building / IEE regulations.
In the Republic of Ireland:
Safety Requirements and Regulations
The installation must be carried out by a competent person
and installed in accordance with the current edition of IS 813
“Domestic Gas Installations”, the current Building Regulations
and reference should be made to the current ETCI rules for
electrical installation.
You must be aware of the following safety requirements &
regulations.
Provision of Ventilation
Before installation, make sure that the local
nn
distribution conditions (nature of the gas and gas
This appliance is not connected to a combustion products
evacuation device. Particular attention shall be given to the
relevant requirements regarding ventilation.
pressure) and the adjustment of the appliance are
compatible.
All rooms require a window that can be opened, or
equivalent, while some rooms require a permanent vent in
addition to the window.
If the appliance is to be installed in Switzerland,
nn
the following regulations and directives should be
observed:
• SVGW - Gas principles G1: Gas installation.
• EKAS - Form. 1942: Liquid gas directive, Part 2.
• Cantonal instances regulations (e.g. fire safety
regulators).
In the UK:
The appliance must be installed in accordance with
nn
the regulations in force and only in a well-ventilated
The room containing the cooker should have an air supply
in accordance with BS 5440 Part 2. All rooms require an
openable window or equivalent, while some rooms require
a permanent vent in addition to the openable window. The
cooker should not be installed in a bedsitting room with
volume less than 20 m³. If it is to be installed in a room of
volume less than 5 m³ an air vent of effective area 100 cm² is
required. If it is installed in a room of volume between 5 m³
and 10 m³ an air vent of effective area 50 cm² is required,
while if the volume exceeds 11 m³ no air vent is required.
Read the instructions before installing or using this
nn
appliance.
If there are other fuel burning appliances in the same room,
the current BS 5440 Part 2 should be consulted to determine
the requisite air vent requirements.
This cooker is a Class 2 Subclass 1 appliance.
nn
This appliance can be converted for use on another
nn
gas.
space.
In the Republic of Ireland:
Failure to install the appliance correctly could
nn
invalidate any warranty or liability claims and lead
Reference should be made to the current edition of IS 813,
which makes clear the conditions that must be met to
demonstrate that sufficient ventilation is available.
to prosecution.
21
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Checking the Parts:
Location of Cooker
The cooker may be installed in a kitchen/kitchen diner but
NOT in a room containing a bath or shower.
3 pan supports (Classic shown)
Plinth (1-piece model shown)
Griddle
Grill pan & trivet
This appliance is designed for domestic cooking only. Use
for any other purpose could invalidate any warranty or
liability claim.
Note: An appliance for use on LPG must not be installed
in a room or internal space below ground level, e.g. in a
basement.
Conversion
This appliance is supplied set for G20 20 mbar Cat II2H3+.
ArtNo.330-0002 - Grill pan w handle
A conversion kit for another gas is available for the cooker.
If the appliance is to be converted to another gas we
recommend that this is carried out before installation.
After converting the appliance, please attach the Gas
Conversion sticker over the appropriate area of the data
badge – this will identify the gas type for which the appliance
is now set.
3 flat shelves
ArtNo.324-0003 Handyrack
You will need the following equipment to complete the
cooker installation satisfactorily:
•
•
•
•
Handyrack
Stability bracket: If the cooker is to be supplied with
gas through a flexible hose, a stability bracket or chain
MUST be fitted.
These are not supplied with the cooker but are
available at most builders’ merchants.
Gas pressure tester/manometer.
Flexible gas hose: Must be in accordance with the
relevant standards.
Multimeter: For electrical checks.
Roasting tin
ArtNo.324-0004 Roasting tin
You will also need the following tools:
1.
2.
Electric drill
Masonry drill bit (only required if fitting the cooker on a
stone or concrete floor)
3. Wall plugs (only required if fitting the cooker on a stone
or concrete floor)
4. Steel tape measure
5. Cross head screwdriver
6. Flat head screwdriver
7. Spirit level
8. Pencil
9. Adjustable spanner
10. Screws for fitting stability bracket
11. 4 mm & 3 mm Allen keys
12. 13 mm spanner or socket wrench
22
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Positioning the Cooker
Fig.8.1
75 mm
min
650 mm
min
Fig.8.1 and Fig.8.2 show the minimum recommended
distance from the cooker to nearby surfaces.
75 mm
min
The cooker should not be placed on a base.
The hotplate surround should be level with, or above, any
adjacent work surface.
A gap of 75 mm should be left between each side of the
cooker ABOVE the hotplate level and any adjacent vertical
surface.
905 mm
min
930 mm
max
For non-combustible surfaces (such as unpainted metal or
ceramic tiles), this can be reduced to 25 mm.
ArtNo.110-0069 - 110DF - Lidded min spacings
Fig.8.2
A minimum space of 650 mm is required between the top of
the hotplate and a horizontal combustible surface.
*Any cookerhood should be installed in accordance with the
hood manufacturer’s instructions.
1096 mm min*
410 mm min
5 mm
**
**Any splashback must be fitted in accordance with the
manufacturers instructions. Allowance should be made for the
additional height of the flue trim, which is fitted to the cooker
hob.
5 mm
Surfaces of furniture and walls at the sides and rear of the
appliance should be heat, splash and steam resistant. Certain
types of vinyl or laminate kitchen furniture are particularly
prone to heat damage and discolouration.
ArtNo.110-0047 - 110 Clearances #2
Wall finish should not
overhang the side trim
Allow sufficient clearance
for the lid to open fully
We cannot accept responsibility for damage caused by
normal use of the cooker to any material that de-laminates
or discolours at temperatures less than 65 °C above room
temperature.
We recommend a gap of 1106 mm between units to allow
for moving the cooker. Do not box the cooker in – it must
be possible to move the cooker in and out for cleaning and
servicing.
Fig.8.3
Make sure that the wall above and behind the cooker is flat
and free of protrusions. To avoid problems opening the lid
fully, the side trim should fit flush to the wall and no part of
the wall should overhang the cooker (Fig.8.3).
Fig.8.4
If the cooker is near a corner of the kitchen a clearance of
130 mm is required to allow the oven doors to open
(Fig.8.4). The actual opening of the doors is slightly less but
this allows for some protection of your hand as you open the
door.
130 mm
Fig.8.5
23
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Moving the Cooker
Fig.8.6
On no account try and move the cooker while it is
plugged into the electricity supply.
nn
The cooker is very heavy, so take great care.
nn
We recommend that two people manoeuvre the cooker.
Make sure that the floor covering is firmly fixed, or removed,
to prevent it being disturbed when moving the cooker
around.
To help you, there are two levelling rollers at the back, and
two screw-down levelling feet at the front.
Fig.8.7
Remove the polystyrene base pack. From the front, tilt
the cooker backwards and remove the front half of the
polystyrene base (Fig.8.5). Repeat from the back and remove
the rear half of the polystyrene base.
Lowering the Two Rear Rollers
ArtNo.010-0004 Moving the cooker
To adjust the height of the rear of the cooker, first fit a 13 mm
spanner or socket wrench onto the hexagonal adjusting
nut (Fig.8.6). Rotate the nut – clockwise to raise – counterclockwise to lower.
Fig.8.8
Make 10 complete (360°) turns clockwise.
Stability chain
Make sure you lower BOTH REAR ROLLERS.
Completing the Move
Unfold the rear edge of the cardboard base tray. Open the
grill door and right-hand oven door so that you can get a
good grip on the bottom of the fascia panel as you move the
oven (Fig.8.7).
Carefully push the cooker backwards off the base tray.
Remove the base tray.
Position the cooker close to its final position, leaving just
enough space to get behind it.
Stability bracket
Fig.8.9
DO NOT use the door handles or control knobs to
nn
manoeuvre the cooker.
Cooker
Fitting the Stability Bracket or Chain
Unless otherwise stated, a cooker using a flexible gas
connector must be secured with a suitable stability device.
3 mm min
ArtNo.070-0014 - Stability bracket - WallFloor
fitting
Suitable stability devices are shown in Fig.8.8, Fig.8.9 and
Fig.8.10.
Typical floor mounting
Typical floor mounting
If you are using a stability chain (Fig.8.8) then the chain
should be kept as short as is practicable and fixed firmly to
the rear of the cooker.
Fig.8.10
Outer stability
bracket
If you are using a stability bracket (Fig.8.9 and Fig.8.10), then
adjust the bracket to give the smallest practicable clearance
between the bracket and the engagement slot in the rear of
the cooker.
Cooker
3 mm min
Fit the bracket so that it engages as far as possible over the
chassis of the cooker.
Wall
Floor
Typical wall mounting
Typical wall mounting
24
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Repositioning the Cooker Following
Connection
Fig.8.11
If you need to move the cooker once it has been connected
then you need to unplug it and, having gripped under the
fascia panel and lifted the front of the cooker slightly
(Fig.8.7), you need to check behind the cooker to make sure
that the gas hose is not caught.
ArtNo.215-0026 - Handle gaskets fixed
As you progress, make sure that both the electricity cable and
gas hose always have sufficient slack to allow the cooker to
move.
Fig.8.12
With a stability chain fitted, release it as you ease the cooker out.
Do not forget to refit it when you replace the cooker.
ArtNo.210-0006 - Classic fitting the handles 2
When you replace the cooker, again check behind to make
sure that the electricity cable and gas hose are not caught or
trapped.
Conversion to Another Gas
If the appliance is to be converted to another gas do the
conversion at this point. See the conversion section of these
instructions.
Fig.8.13
Levelling
You are recommended to use a spirit level on a shelf in one of
the ovens to check for level.
Art No 215-0028 - Handrail fascia fixings
Place the cooker in its intended position taking care not to
twist it within the gap between the kitchen units as damage
may occur to the cooker or the units.
The front feet and rear rollers can be adjusted to level the
cooker.
To adjust the height of the rear of the cooker use a 13 mm
spanner or socket wrench to turn the adjusting nuts at the
front bottom corners of the cooker.
To set the front, turn the feet bases to raise or lower.
Fitting the Handles and Handrail (Classic
only)
Remove the 4 mm Allen screws from the doors (Fig.8.11). Fit
the door handles and secure using the 4 mm screws.
The handles should be above the fixings.
nn
Fit the plastic blanking plugs to the fixing holes (Fig.8.12).
Remove the 4 mm Allen screws from the top corners of the
fascia (Fig.8.13). Fit the handrail in position and secure using
the 4 mm screws.
25
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Gas Connection
Fig.8.14
This must be in accordance with the relevant standards.
600
350
The flexible hose (not supplied with the cooker) must be
in accordance with the relevant standards. Hoses may be
purchased at most builders’ merchants.
100
250
The gas supply needs to terminate with a down-facing
bayonet.
The connector is located just below the hotplate level at the
rear of the cooker. If in doubt contact your supplier.
Gas inlet
block
The rear cover boxes limit the position of the supply point.
Because the height of the cooker can be adjusted and
each connection is different, it is difficult to give precise
dimensions.
Although a 900 mm hose can be used, a 1250 mm hose
will allow slightly more flexibility in the positioning of the
bayonet and make moving the cooker easier.
All dimensions in millimetres
The hose should be fitted so that both inlet and outlet
connections are vertical so that the hose hangs downwards in
a ‘U’ shape.
Ideally the hose supply connection should be within the
shaded area ‘A’ (Fig.8.14).
For Natural Gas, the flexible hose must be in accordance with
BS 669. For LP Gas, it should be capable of 50 mbar pressure,
70 °C temperature rise, and carry a red stripe, band or label. If
in doubt contact, your supplier.
Screw connect the threaded end of the hose into the gas
inlet.
After completing the gas connection, make sure that the
cooker is gas sound with a pressure test.
Pressure Testing
The gas pressure can be measured at one of the hotplate
burner injectors (not the wok burner).
Lift off a burner head. Fit the pressure gauge to the injector.
Turn on and light one of the other hotplate burners.
Turn on the control knob for the burner with the pressure
gauge fitted to let gas through.
See the data badge for test pressures.
Turn off the burners. Make sure that you reassemble the
burner top in the correct way on the burner body.
26
Position for gas
supply connector
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Electrical Connection
Current Operated Earth Leakage Breakers
The combined use of your cooker and other domestic
appliances may cause nuisance tripping, so we recommend
that the cooker is protected on an individual RCD (Residual
Current Device) or RCBO (Residual Current Breaker with
Overload).
The cooker must be installed by a qualified electrician, in
accordance with all relevant British Standards/Codes of
Practice (in particular BS 7671), or with the relevant national
and local regulations.
Note: The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double-pole
switch, having a contact separation of at least 3 mm in all
poles.
IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED
ELECTRICIAN.
Fig.8.15
The cooker MUST NOT be connected to an ordinary
nn
domestic power point.
L
N
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel. Connect
the mains cable to the correct terminals for your electrical
supply type (Fig.8.15 and Fig.8.16). Check that the links are
correctly fitted and that the terminal screws are tight. Secure
the mains cable using the cable clamp.
10 mm² max
Final Checks
ArtNo.130-0010 Electrical connections single-phase6 mm² max
230 V ac 50 Hz
Hotplate Check
Check each burner in turn (refer to the ‘Hotplate Burners’
section at the front of the instructions).
Fig.8.16
L1
Grill Check
N
L3
L2
Oven Check
Turn on the grill control and check that the grill heats up.
Set the clock as described earlier in the instructions, and then
turn on the ovens. Check that the oven fans start to turn and
that the ovens start to heat up.
6 mm² max
6 mm² max
Note: The oven light bulb is not included in the guarantee.
3N ac
230/400 V 50 Hz
Turn off the oven.
10 mm² max
Fitting the Plinth
Loosen the 3 screws along the front bottom edge of the
cooker. Hook the central keyhole over the central screw. Twist
and fit each end keyhole over their respective screws.Tighten
the fixing screws (Fig.8.17).
Fig.8.17
Customer Care
Installer: Please complete your details in this guide, inform
the user how to operate the cooker and hand over the
instructions.
Thank you.
ArtNo.350-0012 - Securing the plinth
27
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
9. Conversion to LP Gas
Check the ‘Technical Data’ section at the back of the book
that the hob is convertible to the gas you want to use.
A suitably competent person must perform the conversion.
After conversion the installation must comply with the
relevant regulations and also the local electricity supply
company requirements. Read the instructions before
converting this appliance.
Fig.9.1
B
Failure to convert the appliance correctly could
nn
invalidate any warranty or liability claims and lead
A
to prosecution.
When servicing or replacing gas-carrying
components disconnect from the gas supply before
starting operation. Check the appliance is gas sound
after completion.
C
ArtNo.311-0010 Injectors
nn
A – Jet, B – Internal injector, C – External injector
Fig.9.2
DO NOT use reconditioned or unauthorised gas
nn
controls.
Disconnect from the electricity and gas supply
nn
before servicing.
Before electrical reconnection, check that the
nn
appliance is electrically safe.
Art No 215-0028 - Handrail fascia fixings
Injectors
Remove the burner caps and heads. Remove the old jets
(Fig.9.1). Fit the new jets (see the ‘Technical Data’ section at
the back of this book for the correct jets). Reassemble in the
reverse order.
Fig.9.3
ArtNo.0102-0011 - Screwing
the control valve bypass screw
Tap Adjustment
Classic – Removing the Control Panel
Remove the handrail. Now remove the 2 cross-headed screws
hidden behind the handrail end brackets (Fig.9.2).
Pull off all the control knobs and remove the fixing screws
underneath the control panel.
Lift the control panel and pull forwards, taking care not to
damage or strain the wiring.
Rangemaster & Toledo – Removing the Control
Panel
Pull off all the control knobs and remove the fixing screws
underneath the control panel.
Slide the control panel to the right and then pull forwards,
taking care not to damage or strain the wiring.
Bypass Screw Adjustment
Turn the bypass screw on each control clockwise to the stop
(Fig.9.3).
Refit the control panel.
28
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Stick on Label
Stick the LP gas label over the natural gas part of the
appliance data label.
Pressure Testing
Connect the appliance to the gas supply.
Check the appliance is gas sound.
The gas pressure can be measured at one of the hotplate
injectors (not the wok burner).
Lift off a burner head. Fit the pressure gauge to the jet. Turn
on and light one of the other burners. Turn on and press in
the control knob for the burner with the pressure gauge
fitted.
The pressure should be 29 mbar for Butane and 37 mbar for
Propane. After checking the pressure, turn off the taps and
replace the burner head.
Reassemble burner top, making sure it is reassembled in the
correct way on the burner body.
Check operation of all the burners.
29
10. Circuit Diagram
b
y
J
br br
A1
bk
bk
r
br
b
br
y
br
r
r
v
A2
r
bk
A3
r
w
b
J
1
w
y
w
B1
w
w
b
B5
b
P1
y
y
D2
2
y
br
P2
3
1
P1
2
P3
v
r
v
r
H2
P093292
b
B2
D3
br
H1
w
5
B3
B4
P2
1
K
F1
4
or
gr
y
or
br
2
P095199
4
K
D1
2
b
w
w
1
w
v
J
y
y
C
I1
b
b
b
r
D4
br
G1
I2
b
P3
5
v
P025635
b
b
d
e
c
b
br br
b b
1
2
b
F2
a
v
J
r
f
br
b
r
G2
br
br
P1
2
b
b
P2
3
1
b
b
E
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
Code Description
A1
Code Description
Grill control
F1
Key
Warmer control
A2 Grill element left-hand side
F2 Warmer
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
A3 Grill element right-hand side
G1 Igntion switch
B1
B2
B3
B4
Key
Description
Key
A1
Grill control
G2
Ignition spark generator
A2
Grill element left-hand side
H1
A3
Grill element right-hand side
Left-hand oven thermostat
Left-hand oven control
Left-hand oven browning element
Left-hand oven top element
B1
Left-hand oven thermostat
B5 B2
Left-hand
oven
base
element
Left-hand
oven
control
C B3
Clock
Left-hand oven base element
D1 B4
Right-hand
fan
oven
Left-hand
oven
topthermostat
element
Description
G2
Ignition spark generator
H1
Left-hand oven light switch
H2
Left-hand oven light
I1
Right-hand oven light switch
Code Colour
b
Blue
br
Brown
bk
Black
Code Colour
or
Orange
b
Blue
Left-hand oven light switch
br
Brown
H2
Left-hand oven light
bk
Black
I1
Right-hand oven light switch
or
Orange
I2
I2 Right-hand
Right-hand
oven lightoven light
yr
Yellow
Red
J
J
Neon
K
K
Thermal
Thermal
cut-out cut-out
Neon
D2 B5
Right-hand
fan
oven
switch element
Left-hand
oven
browning
r
v
w
Red
Violet
White
g/y
v
Green/yellow
Violet
gr
w
Grey
White
y
Yellow
Clock fan oven fan
D3 CRight-hand
g/y
Green/Yellow
Right-hand
oven
thermostat
D4 D1
Right-hand
fanfan
oven
element
gr
Grey
D2
Right-hand fan oven switch
D3
Right-hand fan oven element
D4
Right-hand fan oven fan
F1
Warmer control
F2
Warmer
G1
Igntion switch
30
11. Technical Data
Classic Lidded
THE COOKER IS CATEGORY: CatII2H3+.
It is supplied set for group H natural gas. A conversion kit from NG to LP is available for the cooker.
INSTALLER: Please leave these instructions with the user.
DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.
COUNTRY OF DESTINATION: GB, IE, FR, NL, DE, SE, IT, AT, CH, LU, BE.
Connections
Gas (Rp ½ at rear right-hand side)
Electric
Natural Gas
20 mbar
Butane
29 mbar
Propane
37 mbar
230/400 V 50 Hz
See the appliance badge for test pressures.
Dimensions
Model
Classic Lidded 110 Dual Fuel
Overall height
maximum 930 mm
minimum 905 mm
Overall width
1105 mm
Overall depth
600 mm excluding handles, 650 mm including handles
Minimum height above the hotplate
650 mm
Hotplate Ratings
Hotplate
Bypass
Screw*
Natural Gas 20 mb
L.P. Gas
Injector
Injector
Wok burner
57
3.5 kW
internal 78
external 126
3.5 kW (246 g/h
internal 53
external 82
Rapide/ Large Burner
40
3 kW
134
3.0 kW (210 g/h)
87
Semi Rapide / Medium Burner
32
1.7 kW
109
1.7 kW (119 g/h)
68
Auxiliary / Small Burner
28
1 kW
75
1.0 kW (70 g/h)
51
* The valves in this cooker are fitted with adjustable bypass screws. The cooker is supplied with the bypass screws set for Natural Gas. For LPG conversion the
bypass screws must be screwed all the way down.
Hotplate energy saving tips
Oven energy saving tips
Use cookware with a flat base.
Cook meals together, if possible.
Use the correct size cookware.
Keep the pre-heating time short.
Use cookware with a lid.
Do not lengthen cooking time.
Minimise the amount of liquid or fat.
Do not open the oven door during the cooking period.
When liquid starts boiling, reduce the setting.
Do not forget to turn the appliance off at the end of cooking.
Consumption is based on G30.
31
Rangemaster Lidded
THE COOKER IS CATEGORY: CatII2H3+.
It is supplied set for group H natural gas. A conversion kit from NG to LP is available for the cooker.
INSTALLER: Please leave these instructions with the user.
DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.
COUNTRY OF DESTINATION: GB, IE, FR, NL, DE, SE, IT, AT, CH, LU, BE.
Connections
Gas (Rp ½ at rear right-hand side)
Electric
Natural Gas
20 mbar
Butane
29 mbar
Propane
37 mbar
230/400 V 50 Hz
See the appliance badge for test pressures.
Dimensions
Model
Rangemaster Lidded 110 Dual Fuel
Overall height
maximum 930 mm
minimum 905 mm
Overall width
1105 mm
Overall depth
600 mm excluding handles, 650 mm including handles
Minimum height above the hotplate
650 mm
Hotplate Ratings
Hotplate
Bypass
Screw*
Natural Gas 20 mb
L.P. Gas
Injector
Injector
3.5 kW (246 g/h
internal 53
external 82
Wok burner
57
3.5 kW
internal 78
external 126
Rapide/ Large Burner
40
3 kW
134
3.0 kW (210 g/h)
87
Semi Rapide / Medium Burner
32
1.7 kW
109
1.7 kW (119 g/h)
68
Auxiliary / Small Burner
28
1 kW
75
1.0 kW (70 g/h)
51
* The valves in this cooker are fitted with adjustable bypass screws. The cooker is supplied with the bypass screws set for Natural Gas. For LPG conversion the
bypass screws must be screwed all the way down.
Hotplate energy saving tips
Oven energy saving tips
Use cookware with a flat base.
Cook meals together, if possible.
Use the correct size cookware.
Keep the pre-heating time short.
Use cookware with a lid.
Do not lengthen cooking time.
Minimise the amount of liquid or fat.
Do not open the oven door during the cooking period.
When liquid starts boiling, reduce the setting.
Do not forget to turn the appliance off at the end of cooking.
Consumption is based on G30.
32
Toledo Lidded
THE COOKER IS CATEGORY: CatII2H3+.
It is supplied set for group H natural gas. A conversion kit from NG to LP is available for the cooker.
INSTALLER: Please leave these instructions with the user.
DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.
COUNTRY OF DESTINATION: GB, IE, FR, NL, DE, SE, IT, AT, CH, LU, BE.
Connections
Gas (Rp ½ at rear right-hand side)
Electric
Natural Gas
20 mbar
Butane
29 mbar
Propane
37 mbar
230/400 V 50 Hz
See the appliance badge for test pressures.
Dimensions
Model
Toledo Lidded 110 Dual Fuel
Overall height
maximum 930 mm
minimum 905 mm
Overall width
1105 mm
Overall depth
600 mm excluding handles, 650 mm including handles
Minimum height above the hotplate
650 mm
Hotplate Ratings
Hotplate
Bypass
Screw*
Natural Gas 20 mb
L.P. Gas
Injector
Injector
3.5 kW (246 g/h
internal 53
external 82
Wok burner
57
3.5 kW
internal 78
external 126
Rapide/ Large Burner
40
3 kW
134
3.0 kW (210 g/h)
87
Semi Rapide / Medium Burner
32
1.7 kW
109
1.7 kW (119 g/h)
68
Auxiliary / Small Burner
28
1 kW
75
1.0 kW (70 g/h)
51
* The valves in this cooker are fitted with adjustable bypass screws. The cooker is supplied with the bypass screws set for Natural Gas. For LPG conversion the
bypass screws must be screwed all the way down.
Hotplate energy saving tips
Oven energy saving tips
Use cookware with a flat base.
Cook meals together, if possible.
Use the correct size cookware.
Keep the pre-heating time short.
Use cookware with a lid.
Do not lengthen cooking time.
Minimise the amount of liquid or fat.
Do not open the oven door during the cooking period.
When liquid starts boiling, reduce the setting.
Do not forget to turn the appliance off at the end of cooking.
Consumption is based on G30.
33
Hotplate Efficiency Classic and Toledo Lidded
Brand
Rangemaster
Classic Lidded
Model Identification
Toledo Lidded
Size
110
Type
Dual Fuel
Type of Hob
GAS
Number of gas burners
5
Auxiliary / Small Burner (EE gas burner)
-
Semi Rapide / Medium Burner (EE gas burner)
58%
Semi Rapide / Medium Burner (EE gas burner)
58%
Rapide / Large Burner (EE gas burner)
56%
Rapide / Large Burner (EE gas burner)
-
Wok (EE gas burner)
53%
Wok (EE gas burner)
-
Hotplate EE gas hob (*)
56%
Information marked thus (*) is not required with mixed fuel hobs
34
Hotplate Efficiency
Brand
Rangemaster
Model Identification
Rangemaster
Lidded
Size
110
Type
Dual Fuel
Type of Hob
GAS
Number of gas burners
5
Auxiliary / Small Burner (EE gas burner)
-
Semi Rapide / Medium Burner (EE gas burner)
58%
Semi Rapide / Medium Burner (EE gas burner)
58%
Rapide / Large Burner (EE gas burner)
56%
Rapide / Large Burner (EE gas burner)
56%
Wok (EE gas burner)
-
Wok (EE gas burner)
-
Hotplate EE gas hob (*)
57%
Information marked thus (*) is not required with mixed fuel hobs
35
Oven Data Classic and Rangemaster Lidded
Brand
Rangemaster
Model identification
Classic Lidded
Mass
kg
Model identification
126
Rangemaster Lidded
Mass
kg
Type of oven
124
Electric
Number of cavities
2
Left-hand Efficiency
Fuel type
Electric
Cavity type
Convection
Power - conventional
2.2
Power - forced air convection
-
Volume
Litres
80
Energy consumption (electricity) - conventional
kWh / cycle
1.03
Energy consumption (electricity) - forced air convection
kWh / cycle
-
Energy efficiency index - conventional
116.3
Energy efficiency index - forced air convection
-
Energy class
B
Right-hand Efficiency
Fuel type
Electric
Cavity type *Drop Down Door
Fanned
Power - conventional
-
Power - forced air convection
2.5
Volume
Litres
67
Energy consumption (electricity) - conventional
kWh / cycle
-
Energy consumption (electricity) - forced air convection
kWh / cycle
0.8
Energy efficiency index - conventional
-
Energy efficiency index - forced air convection
96.2
Energy class
A
Additional Information
The oven complies with EN 60350-1
Maximum output @ 230V 50Hz
Conventional
2.2 kW
Multifunction
2.5 kW
-
Multifunction (with Rapid Response)
Forced Air Convection
2.5 kW
Grill
2.3 kW
Slow Oven
-
Bread Proving Drawer
-
Maximum total electrical load at 230 V (approximate total including hob, oven lights, oven fan, etc.):
36
7.2 kW
Oven Data
Brand
Rangemaster
Model identification
Toledo Lidded
Type of oven
Electric
Mass
kg
124
Number of cavities
2
Left-hand Efficiency
Fuel type
Gas
Cavity type
Convection
Power - conventional
2.5
Power - forced air convection
-
Volume
Litres
61
Energy consumption (electricity) - conventional
kWh / cycle
-
Energy consumption (electricity) - forced air convection
kWh / cycle
-
Energy efficiency index - conventional
-
Energy efficiency index - forced air convection
-
Energy class
-
Right-hand Efficiency
Fuel type
Gas
Convection
Cavity type *Drop Down Door
Power - conventional
2.5
Power - forced air convection
-
Volume
Litres
61
Energy consumption (electricity) - conventional
kWh / cycle
-
Energy consumption (electricity) - forced air convection
kWh / cycle
-
Energy efficiency index - conventional
-
Energy efficiency index - forced air convection
-
Energy class
-
Additional Information
The oven complies with EN 60350-1
Maximum output @ 230V 50Hz
Conventional
2.2 kW
Multifunction
2.5 kW
-
Multifunction (with Rapid Response)
Forced Air Convection
2.5 kW
Grill
2.3 kW
Slow Oven
-
Bread Proving Drawer
-
Maximum total electrical load at 230 V (approximate total including hob, oven lights, oven fan, etc.):
37
7.2 kW
For warranty compliance, the requirements are
that the appliance:
Name of Appliance & Colour*
•
Has been correctly installed in accordance with current
legislation, relevant British and European Standards and
Codes of Practice, by a suitably competent person registered
with Gas Safe or equivalent body and, where applicable, a
qualified electrician.
•
Has been used solely for domestic cooking purposes.
•
If in use in the UK*, has not been taken abroad as a personal
export. (In the Republic of Ireland conditions may vary, so
consult your retailer.)
•
Is not second-hand or a refurbished appliance. The
manufacturer’s warranty is not transferable.
•
Has not been subject to misuse, accidental damage or
modification, and has not deteriorated due to normal
domestic wear and tear, and the manufacturer’s
recommendations concerning cleaning materials have been
followed.
•
Has not been repaired by persons or organisations other than
those authorised to act on behalf of AGA Rangemaster.
Appliance Serial Number*
Natural Gas
LP Gas
Dual Fuel
Electric
Fuel Type*
Retailer’s Name & Address
Date of Purchase
Installer’s Name & Address
Installer’s Telephone Number
Date of Installation
*This information is on the appliance data badge - look in the appliance instructions
to find out where the data badge is located.
CONSUMER SERVICE
If you have any product enquiries, or in the event of a problem
with your appliance once it has been installed, please
telephone 0800 804 6261 or 0370 789 5107
from a mobile.
CONSUMER SERVICE LINES OPEN:
Monday to Thursday 8am–6pm
Friday 8am–5pm
Saturday 9am–1pm
WARRANTY
Your manufacturer warranty covers goods of our own brand for
defective workmanship and materials for a period of 1 year from the
date of purchase. This warranty covers mechanical breakdown and
proven cosmetic and manufacturing defects.
You will receive an additional FREE full 12 months guarantee by
registering your purchase using the FREEPOST form provided.
Alternatively, call free on 0800 587 5747, quoting reference
RMGX57A, or register online at www.rangemaster.co.uk.
Any damage, blemishes or chips identified upon receipt of the
product must be reported within 90 days – proof of purchase
may be required to establish validity. Scratches on the surface of
ceramic hobs must be reported within 14 days. Scratches caused
by usage are not covered. Accidental damage is not covered by the
manufacturer’s warranty.
Exceptions:
•
Items not included under the free 1 year guarantee include
pan supports, griddles, wok rings, baking trays, grill pans,
trivets, filters, light bulbs and other consumable accessories.
•
Any damage caused other than through normal use.
•
Breakdowns associated with cooking spillage.
•
Cosmetic deterioration deemed to be normal wear and tear.
This warranty is in addition to your Statutory Rights.
* Only certain models can be adapted for use with Mains Gas
supplied in the Channel Islands and Isle of Man.
OUT OF WARRANTY
We recommend that Rangemaster appliances are serviced regularly
throughout their life to maintain optimum performance and
efficiency. Service work should only be carried out by technically
competent and suitably qualified personnel.
For your own safety, always make sure that work is carried out by
a Gas Safe registered engineer for gas appliances or an approved
electrician for electrical models.
For a competetive quote and to arrange for a Rangemaster
approved engineer to attend, call Consumer Services on:
0800 804 6261 or 0370 789 5107 from a mobile.
SPARE PARTS
To maintain optimum and safe performance, we recommend
that only genuine Rangemaster spare parts are used. These are
available from most major spares stockists, including ourselves.
Contact Consumer Services on 0800 804 6261 or 0370 789 5107
from a mobile, who will be happy to help.
STANDARDS
Rangemaster cookers are designed and manufactured to
a recognised international quality standard, which meets
the requirements of BS EN ISO 9001, BS EN ISO 14001 and
OHSAS 18001 for continually improving environmental procedures.
Rangemaster cookers comply with the essential requirements of
the appropriate European Directives, and carry the CE mark.
Designed to impress
The Co-ordinating Collection.
•Refrigeration • Sinks & Taps • Hoods & Splashbacks • Built-in Cooking • Dishwashing
Built from experience
Clarence Street
Royal Leamington Spa
Warwickshire
CV31 2AD
England
Consumer Services: +44 (0)800 804 6261 or (0)370 789 5107 from a mobile.
Fax: +44 (0)1926 450526
E-mail: [email protected]
www.rangemaster.co.uk
For UK Trade Enquiries Tel: +44 (0)115 946 4000
Fax: +44 (0)115 973 6602
E-mail: [email protected]
For ROI Enquiries Tel: 1850 302 502
Rangemaster is a trading name of AGA Rangemaster Limited
Registered in England and Wales. Registration No. 354715
Registered Office: Juno Drive, Leamington Spa, Warwickshire, CV31 3RG
Rangemaster continuously seeks improvements in specification, design and production of products and thus, alterations
take place periodically. Whilst every effort is made to produce up-to-date literature, this brochure should not be regarded as
an infallible guide to current specification, nor does it constitute an offer for the sale of any particular appliance.
4000275
0870648
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement