VQC Series - 5 Port Solenoid Valve

VQC Series - 5 Port Solenoid Valve
CAT.ES11-80 A
5-Port Solenoid Valve
Series VQC
NEW CONCEPT
Connector Type Manifold
Series VQC1000/2000/4000
Outstanding response times
Conforming to IP67 for
and long life
protection from dust
(Metal seal: Single type with light and surge suppressor)
(Based on IEC529)
VQC1100: 10ms ±2ms; 200 million cycles
VQC2100: 20ms ±2ms; 200 million cycles
VQC4100: 17ms ±3ms; 100 million cycles
and moisture
(For kits S and T)
Connector
Compact and high flow
Flow characteristics Note)
Rubber seal
Metal seal
C[dm3/(s•bar)] b Cv C[dm3/(s•bar)] b
Applicable
cylinder
Cv size (mm)
Type
(Series)
Manifold
pitch (mm)
VQC1000
10.5
0.72
0.25 0.18
1.0
0.30 0.25
to ø50
VQC2000
16
2.6
0.15 0.60
3.2
0.30 0.80
to ø80
VQC4000
25
6.9
0.17 1.7
7.3
0.38 2.0
to ø140
Note) Values for 2-position single from the cylinder port to the exhaust. (From 2 to 3 and from 4 to 5)
Connector entry direction
can be changed with a
single push
The connector entry direction can be changed from the
top to the side by simply pressing the manual release
button.
It is not necessary to use the manual release button when
switching from the side to the top.
Accommodates gateway
type serial wiring
Top entry
try
en
e
d
Si
For I/O SI unit
(DeviceNet compatible)
• Gateway unit types are DeviceNet, PROFIBUS-DP and
Remote I/O.
• Because just one gateway unit controls up to 4 branch
lines, it offers much more freedom in choosing valve
mounting locations than do conventional serial units.
• Manifolds and input blocks can be mounted in close
proximity of actuators, thus effectively shortening air
piping and electrical wiring lengths.
• Since wiring is “prepackaged” into one multi-connector
type cable, wiring work is not only made easier, but
much more accurate.
• A single cable from the gateway provides both signal
and power to each branch, thus eliminating the need for
separate power connections for each manifold valve and
input block.
• The use of a multi-connector for input blocks makes
manifold station expansion or reduction a breeze.
Features 1
M12/M8
connector selection available
Serial transmission
EX250
Input blocks
NEW CONCEPT
A wide variety of prepackaged wiring configurations
S
Kit
(Serial transmission)
F
Kit
(D-sub connector)
P
T
Kit
(Flat ribbon cable)
Kit
(Terminal block box)
es
Seri
00
EX5
25-pin
26-pin, 20-pin
Protective enclosure
conforms to IP 67
Protective enclosure
conforms to IP 67
• Our four standard wiring packages bring a world of ease to wiring and maintenance work, while the protective enclosures of two of
them conform to IP67 standards.
• The S Kit is compatible with a combined I/O unit.
Connector wiring diagram (mixed wiring)
(If used with gataway unit, SI must be output only.)
Connector type manifold
• The use of multi-pin connectors to replace wiring inside manifold
blocks provides flexibility when adding stations or changing
manifold configuration.
• Connector clusters give a new dimension to the notion of
interchangeability. For example, changing from F Kit (D-sub
connector) to S Kit (serial transmission) is achieved by simply
changing the kit piece.
3
A
1 2
A B
4 5
A B
6
A
Output
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
COM
19
20
19
20
19
20
19
20
19
20
19
20
19
20
19
20
Station 1
Double wiring
Station 2
Single wiring
Station 3
Double wiring
Station 4
Single wiring
(Refer to the connector wiring diagram)
Printed circuit board patterns between connectors are shifted at every station.
This allows for viable connections to take place without necessarily specifying
whether the manifold station is double, single, or mixed wiring.
Dual 3-port valves, 4 positions
VQC1000/2000 (Rubber seal type only)
• Two 3-port valves built into one body.
• The 3-port valves on the A and B sides can operate
independently.
• When used as 3-port valves, only half the number of
stations is required.
• Can also be used as a 4-position, 5-port type valve.
Single mounting screw,
clamp construction
Replaceable
One-touch fittings
Exhaust center : VQC1A01
VQC2A01
Pressure center: VQC1B01
VQC2B01
R1 A P B R2
Model
A side
B side
JIS symbol
4
(A)
Wiring
VQC1A01
VQC2A01
N.C.
valve
N.C.
valve
VQC1B01
VQC2B01
N.O.
valve
N.O.
valve
5
(R1)
2
(B)
1
(P)
4
(A)
5
(R1)
2
(B)
1
(P)
4
(A)
Serial transmission
EX500
D-sub connector
Flat ribbon cable
Terminal block box
VQC1C01
VQC2C01
N.C.
valve
N.O.
valve
5
(R1)
3
(R2)
3
(R2)
2
(B)
1
(P)
3
(R2)
Features 2
Base-Mounted type: Variations
S Kit
Sonic
Conductance
C[dm3/(s•bar)]
Serial transmission
Gateway application
Applicable bore size
3-position (Closed center)
Single/Double
Values of
CYL to EXH
(From 4 to 5
and
from 2 to 3)
Compatible network
Compatible network
• Remote I/O
• DeviceNet
• PROFIBUS-DP
• DeviceNet
• PROFIBUS-DP
I/O
Decentralized Serial Wiring
Gateway application requires a
gateway unit and
communication cable
separately.
Contact SMC for
more details.
es
Seri
00
Ex5
Serial unit: EX250
Serial unit: EX500
Conforms to IP67
Series
VQC4000
Features 3
1.0
0.65
VQC200
2.6
2.0
Rubber seal
Rubber seal
0.72
Metal seal
0.72
VQC201
3.2
2.2
Metal seal
Series
VQC2000
VQC100
VQC101
VQC400
6.9
6.3
Rubber seal
Series
VQC1000
Metal seal
Conforms to IP67
VQC401
7.3
6.4
to ø50
to ø80
to ø140
—
—
F Kit
T Kit
P Kit
Port size
D-sub connector Flat ribbon cable Terminal block box
D-sub connector
Compatible network
• DeviceNet
• PROFIBUS-DP
I/O
Serial unit: EX240
Conforms to IP67
—
—
Flat ribbon cable
)(
Compatible with
D-sub connector that
complies with MIL standard.
(
Compatible with
flat ribbon cable connector
that complies
with MIL standard.
26-pin
20-pin
25-pin
Terminal block box
)
(Terminal blocks)
Terminals are concentrated
in compact clusters within
the terminal block box.
SUP
port
EHX
Cylinder
port
1, 3
(P, R)
2, 4
(A, B)
Conforms to IP67
C8 (for ø8)
N9 (ø5/16")
—
—
N1 (ø1/8")
N3 (ø5/32")
N7 (ø1/4")
C4 (for ø4)
C6 (for ø6)
C10 (for ø10) C8 (for ø8)
N11 (ø3/8")
N3 (ø5/32")
N7 (ø1/4")
N9 (ø5/16")
<SUP port>
C8 (for ø8)
C10 (for ø10)
C12 (for ø12)
Rc 1/2
C3 (for ø3.2)
C4 (for ø4)
C6 (for ø6)
M5 (M5 thread)
N7 (ø1/4")
(NPT, NPTF, G) N9 (ø5/16")
N11 (ø3/8")
<EXH port> Rc 1/4
Rc 3/8
Rc 3/4
Rc 1/4
(bottom ported)
(NPT, NPTF, G)
(NPT, NPTF, G)
Features 4
Series VQC1000/2000
Base-Mounted Type
Plug-in Unit
How to Order Manifolds
VV5QC 1 1
08 C6 FD1
B ⋅⋅⋅⋅⋅⋅ F / P / T
VV5QC 1 1
08 C6 SDQ
B ⋅⋅⋅⋅⋅⋅ S
VQC1000
VQC2000
Input block COM
(Indicate for I/O unit only)
Manifold type
1
Kit
Options
Series
1
2
Kit
Input block type
(Indicate for I/O unit only)
Plug-in unit
Stations
Number of input blocks
(Indicate for I/O unit only)
Cylinder port size
SI unit COM
Refer to manifold specification sheet on pages 23 to 26
for detailed information on models.
Kit designation/Electrical entry/Cable length
S
Kit
(Decentralized wiring type serial transmission kit)
Serial unit: EX500
S
Kit
(I/O serial transmission kit)
Conforms to IP67
Serial unit: EX250
Conforms to IP67
Note) A separate gateway unit and communication cable are required.
SD0
SDA1
SDA2
F
Serial kit without SI unit
Serial kit for Remote I/O
Serial kit for DeviceNet/PROFIBUS-DP
Kit
(D-sub connector kit)
25-pin
FD0
FD1
FD2
FD3
1 to 8 stations
(16 stations)
P
D-sub connector kit (25P) without cable
D-sub connector kit (25P) with 1.5m cable 1 to 12 stations
D-sub connector kit (25P) with 3.0m cable (24 stations)
D-sub connector kit (25P) with 5.0m cable
PD0
PD1
PD2
PD3
T
Conforms to IP40
Flat ribbon cable kit (26P) without cable
TD0
Flat ribbon cable kit (26P) with 1.5m cable 1 to 12 stations
Flat ribbon cable kit (26P) with 3.0m cable (24 stations)
Flat ribbon cable kit (26P) with 5.0m cable
PDC Flat ribbon cable kit (20P) without cable
1
Serial kit without SI unit
Serial kit for DeviceNet
Serial kit for PROFIBUS-DP
Kit
(Flat ribbon cable kit)
26-pin
20-pin
Conforms to IP40
SD0
SDQ
SDN
1 to 9 stations
(18 stations)
1 to 12 stations
(24 stations)
Kit
(Terminal block box kit)
Conforms to IP67
Terminal block box kit
1 to 10 stations
(20 stations)
VQC1000/2000
Base-Mounted Type
Plug-in Unit
How to Order Valves
5
VQC 1 1 0 0
Series
1
2
Manual override
VQC1000
VQC2000
Nil
E
Type of actuation
2-position single
1
A B
EA PEB
Note)
2-position double (metal)
A B
2
EA P EB
EA PEB
B
Note)
3
C
A B
B: Locking type
3
N.C.
1
5
N.O.
5
N.C.
24VDC
12VDC
Note) For rubber seal type only.
A B
Nil
Seal type
0
1
3-position exhaust center
K
N
R
Y
Metal seal
Rubber seal
EA P EB
Note 1)
(Manual)
Standard type (1W)
High voltage type (1.0MPa)
Negative COM
External pilot
Low-wattage type (0.5W)
Note 1) For metal seal type only.
3-position pressure center
5
C: Locking type
Function
3
N.O.
1
EA P EB
4
5
6
3
N.O.
1
(Slotted)
Coil voltage
4-position dual 3-port valve
4
2
(C)
Note)
3-position closed center
Note) Not applicable to S Kit.
4-position dual 3-port valve
4
2
(B)
2-position double (rubber)
A B
5
N.C.
push type
(Slotted)
With
Without Note)
4-position dual 3-port valve
4
2
(A)
A
Nil: Non-locking
Light/Surge voltage suppressor
Note 2) When specifying more than
one option, enter symbols in
alphabetical order.
A B
EA P EB
Manifold Options
Blanking plate assembly
VVQ1000-10A-1
VVQ2000-10A-1
SUP block plate
VVQ1000-16A
VVQ2000-16A
Dual flow fitting assembly
VVQ1000-52A-C8
VVQ2000-52A-C10
Perfect block
VVQ1000-FPG-
VVQ2000-FPG-
Blanking plate with connector
VVQ1000-1C-
(VQC1000 only)
CY
to L
po
rt
Individual SUP spacer
VVQ1000-P-1-C6
VVQ2000-P-1-C8
EXH block plate assembly
C3
C4
VVQC1000-19A- D
S - C6
M5
Elbow fitting assembly
VVQ1000-F-L
VVQ2000-F-L
Conforms to IP40
Port plug
VVQ0000-58A (For VQC1000)
VVQ1000-58A (For VQC2000)
C6 (SUP port)
ø6 One-touch fitting
Electrical wiring
specifications [-K]
D-sub connector
14
15
Individual EXH spacer
VVQ1000-R-1-C6
VVQ2000-R-1-C8
DIN rail mounting bracket [-D] Silencer (EXH port)
(-S)
AN200-KM8 (For VQC1000)
VVQ1000-57A (-T)
(-S)
AN200-KM10 (For VQC2000)
VVQ2000-57A (-T)
EXH block plate
VVQ2000-19A
C6 (EXH port)
ø6 One-touch fitting
16
17
18
19
20
21
22
23
24
25
1
2
3
4
5
6
7
8
9
10
11
12
13
Station 1
Station 2
Station 3
Station 4
Terminal no.
SOL. A
SOL. A
SOL. A
SOL. A
SOL. A
Station 5
SOL. B
SOL. A
Station 6
Station 7
Station 8
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
COM
1
14
2
15
3
16
4
17
5
18
6
19
13
Connector terminal no.
Conforms to IP40
Back pressure check valve Name plate [-N]
VVQ1000-N-Stations (1 to max. no. of stations) Direct EXH outlet with
Assembly [-B]
VVQ1000-18A, VVQ2000-18A VVQ2000-N-Stations (1 to max. no. of stations) built-in silencer [-S]
9
8
7
6
5
Standard manifolds are for double
wiring, but mixed wiring (single
and double wiring) can be specified as options.
Blanking plug
KQ2P-
Exhaust port
4
3
2
1
Conforms to IP40
2
Series VQC4000
Base-Mounted Type
Plug-in Unit
How to Order Manifolds
VV5QC 4 1
08 02
VV5QC 4 1
16 03 SDQW
⋅⋅⋅⋅⋅⋅ T
TD0
⋅⋅⋅⋅⋅⋅ S Kit
Options
Series
4
Kit
VQC4000
Input block COM
(Indicate for I/O unit only)
Manifold type
1
Number of input blocks
(Indicate for I/O unit only)
Plug-in unit
Stations
SI unit COM
Cylinder port size
Refer to manifold specification sheet on pages 27
and 28 for detailed information on models.
Kit designation/Electrical entry
S
Kit
(I/O serial transmission kit)
Serial unit: EX240
SD0
SDQW
SDNW
T
Conforms to IP67
Serial kit without SI unit
Serial kit for DeviceNet
Serial kit for PROFIBUS-DP
1 to 16 stations
Kit
(Terminal block box kit)
Conforms to IP67
TD0
3
Terminal block box kit 1 to 10 stations (16 stations)
VQC4000
Base-Mounted Type
Plug-in Unit
How to Order Valves
5
VQC 4 1 0 0
Series
4
Manual override
VQC4000
Nil: Non-locking
push type
(Slotted)
Light/Surge voltage suppressor
Type of actuation
Nil
E
2-position single
With
Without light, with surge voltage supressor
A B
1
EA PEB
2-position double (metal)
A B
2
Coil voltage
EA P EB
2-position double (rubber)
5
A B
B: Locking type
(Slotted)
24VDC
EA PEB
3-position closed center
A B
3
Function
Nil
R
Y
EA P EB
3-position exhaust center
A B
4
EA P EB
Note) When specifying more than
one option, enter symbols in
alphabetical order.
3-position pressure center
A B
5
Standard type (1W)
External pilot
Low wattage type (0.5W)
EA P EB
3-position perfect
6
A B
EA P EB
Seal type
0
1
Metal seal
Rubber seal
Manifold Options
Blanking plate assembly
VVQ4000-10A-1
Individual SUP spacer
VVQ4000-P-1- 02
03
Individual EXH spacer
VVQ4000-R-1- 02
03
SUP/EXH block plate
VVQ4000-16A
<EXH block plate>
<SUP block plate>
Throttle valve spacer
VVQ4000-20A-1
Residual pressure release valve
perfect spacer
VVQ4000-25A-1 Note 1)
SUP stop valve spacer
VVQ4000-37A-1
Interface regulator
A
ARBQ4000-00- BP-1
SH
PU
CK
LO
Note1) Perfect spacers with residual pressure release valve cannot be combined with external pilot specifications.
4
Series VQC
Base-Mounted Type
Plug-in Unit
VQC1000
2-position single
4-position
(A)( B)
4 2
5 1 3
(R1) (P)(R2)
2-position
2-position double (metal)
(A) (B)
4 2
VQC2000
5 1 3
(R1) (P) (R2)
3-position closed center
4-position
(A) (B)
4 2
2-position
5 1 3
(R1) (P)
(R2)
5 1 3
(R1) (P)(R2)
3-position pressure center
(A) (B)
4 2
5 1 3
(R1) (P) (R2)
3-position perfect
(A)
4
(B)
2
4-position dual 3-port valve (A)
4
2
3
N.C.
1
4-position dual 3-port valve (B)
4
5
N.O.
2
3
N.O.
1
4-position dual 3-port valve (C)
4
5
N.C.
5
2
1
3
N.O.
b
0.72
0.25 0.18 12 or less 15 or less
Rubber seal VQC1101
0.85
0.20 0.21
1.0
0.30 0.25 15 or less 20 or less
Metal seal
VQC1200
0.70
0.15 0.16
0.72
0.25 0.18 10 or less 13 or less
Rubber seal VQC1201
0.85
0.20 0.21
1.0
0.30 0.25 15 or less 20 or less
Metal seal
VQC1300
0.68
0.15 0.16
0.72
0.25 0.18 20 or less 26 or less
Rubber seal VQC1301
0.70
0.20 0.16
0.65
0.42 0.18 25 or less 33 or less
VQC1400
Exhaust Metal seal
center Rubber seal VQC1401
0.68
0.15 0.16
0.72
0.25 0.18 20 or less 26 or less
0.70
0.20 0.16
1.0
0.30 0.25 25 or less 33 or less
VQC1500
Pressure Metal seal
center Rubber seal VQC1501
0.70
0.15 0.16
0.72
0.25 0.18 20 or less 26 or less
0.85
0.20 0.21
0.65
0.42 0.18 25 or less 33 or less
0.70
0.20 0.16
0.70
0.20 0.16 25 or less 33 or less
VQC2100
2.0
0.15 0.46
2.6
0.15 0.60 22 or less 29 or less
Rubber seal VQC2101
2.2
0.28 0.55
3.2
0.30 0.80 24 or less 31 or less
Metal seal
Single
Double
Metal seal
A
Dual
Rubber seal VQC1B 01
3-port valve
C
Single
Metal seal
VQC2200
2.0
0.15 0.46
2.6
0.15 0.60 15 or less 20 or less
Rubber seal VQC2201
2.2
0.28 0.55
3.2
0.30 0.80 20 or less 26 or less
Metal seal
VQC2300
2.0
0.15 0.46
2.0
0.18 0.46 29 or less 38 or less
Rubber seal VQC2301
2.0
0.28 0.49
2.2
0.31 0.60 34 or less 44 or less
VQC2400
Exhaust Metal seal
center Rubber seal VQC2401
2.0
0.15 0.46
2.6
0.15 0.60 29 or less 38 or less
2.0
0.28 0.49
3.2
0.30 0.80 34 or less 44 or less
VQC2500
Pressure Metal seal
center Rubber seal VQC2501
2.4
0.17 0.57
2.0
0.18 0.46 29 or less 38 or less
3.2
0.28 0.80
2.2
0.31 0.60 34 or less 44 or less
Dual
Rubber seal VQC2 01
3-port valve
1.8
0.28 0.46
1.8
0.28 0.46 34 or less 44 or less
Metal seal
Double
A
B
C
Single
Double
Closed
center
VQC4100
6.2
0.19 1.5
6.9
0.17 1.7 20 or less 22 or less
Rubber seal VQC4101
7.2
0.43 2.1
7.3
0.38 2.0 25 or less 27 or less
Metal seal
VQC4200
6.2
0.19 1.5
6.9
0.17 1.7 12 or less 12 or less
Rubber seal VQC4201
7.2
0.43 2.1
7.3
0.38 2.0 15 or less 15 or less
Metal seal
VQC4300
5.9
0.23 1.5
6.3
0.18 1.6 45 or less 47 or less
Rubber seal VQC4301
7.0
0.34 1.9
6.4
0.42 1.9 50 or less 52 or less
VQC4400
Exhaust Metal seal
center Rubber seal VQC4401
6.2
0.18 1.5
6.9
0.17 1.7 45 or less 47 or less
7.0
0.38 1.9
7.3
0.38 2.0 50 or less 52 or less
VQC4500
Pressure Metal seal
center Rubber seal VQC4501
6.2
0.18 1.9
6.4
0.18 1.6 45 or less 47 or less
7.0
0.38 1.9
7.1
0.38 2.0 50 or less 52 or less
Metal seal
VQC4600
2.7
––
––
3.7
––
––
55 or less 57 or less
Rubber seal VQC4601
2.8
––
––
3.9
––
––
62 or less 64 or less
Perfect
5 1 3
(R1) (P) (R2)
5
N.C.
VQC4000
(A) (B)
4 2
3-position
3-position exhaust center
C[dm3/(s•bar)]
0.15 0.16
Closed
center
3-position
(A) (B)
4 2
4, 2→5, 3 (A, B→R1, R2) Standard:
Low
wattage
1W
Cv
Cv C[dm3/(s•bar)] b
1→4, 2 (P→A, B)
0.70
5 1 3
(R1) (P) (R2)
2-position double (rubber)
Model
Response time ms
VQC1100
Closed
center
3-position
Symbols
Note 2)
Flow characteristics
No. of
solenoids
2-position
Series
Models
Weight
g
64
78
90
110
230
260
280
500
Note 1) Values represented in this column are in the following conditions:
VQC1000: Cylinder port size C6 without a back pressure check valve
VQC2000: Cylinder port size C8 without a back pressure check valve
VQC4000: Cylinder port size Rc 3/8
Note 2) Values represented in this column are based on JISB8375-1981 (operating with clean air and a supply pressure
of 0.5MPa. Equipped with light and surge voltage suppressor. Values vary depending on the pressure as well as
the air quality.) Values for double types are when the switch is ON.
VQC
Base-Mounted Type
Plug-in Unit
Standard Specifications
Valve Configuration
Metal seal
VQC1000/2000
VQC4000
Valve specifications
Fluid
Max. operating pressure
0.7MPa (High pressure type: 1.0MPa) Note 4)
Single
0.1MPa
0.15MPa
0.1MPa
Double
Min. operating
pressure
3-position
0.1MPa
4-position
—
0.2MPa
0.15MPa
Max. operating pressure Note 3)
1.0MPa (0.7MPa)
Single
Min. operating
Double
pressure
0.2MPa
0.15MPa
0.15MPa
3-position
0.2MPa
0.15MPa
1.5MPa
Proof pressure
–10° to 50°C Note 1)
Ambient and fluid temperature
Lubrication
Not required
Push type/Locking type (tool required) optional
Manual override
150/30 m/s² Note 2)
Impact resistance/Vibration resistance
Enclosure
Electrical
specifications
Rubber seal
Air/Inert gas
Dust proof (conforms to IP67)
Rated coil voltage
24VDC
±10% of rated voltage
Allowable voltage fluctuation
Equivalent to B type
Coil insulation type
1W DC (42mA), 0.5W DC (21mA)
Power consumption (Current) 24VDC
Note 1) Use dry air to prevent condensation at low temperatures.
Note 2) Impact resistance: No malfunction resulted from the impact test using a drop impact tester. The test was
performed one time each in the axial and right angle directions of the main valve and armature, for both
energized and de-energized states.
Vibration resistance: No malfunction occurred in a one-sweep test between 8.3 and 2000Hz. Test was
performed in the axial and right angle directions of the main valve and armature for both energized and
de-energized states.
Note 3) Values in ( ) are for the low wattage (0.5W) specification.
Note 4) Metal seal type only.
Manifold Specifications
Piping specifications
Series
VQC1000
Base model
VV5QC11-
Connection type
Port
direction
1, 3 (P, R)
2, 4 (A, B)
F Kit: D-sub connector
C8 (for ø8)
C3 (for ø3.2)
P Kit: Flat ribbon cable
Options
C4 (for ø4)
Direct outlet
with built-in
silencer
M5 (M5 threads)
T Kit: Terminal block box
Side
S Kit: Serial transmission
VQC2000
VV5QC21-
Note 2)
F Kit: D-sub connector
C10 (for ø10)
P Kit: Flat ribbon cable
Options
T Kit: Terminal block box
Side
S Kit: Serial transmission
Applicable
stations
Port size Note 1)
C6 (for ø6)
C4 (for ø4)
C6 (for ø6)
Direct outlet
with built-in
silencer
C8 (for ø8)
(
)
(1 to 10T Kitstations)
F and P Kits
1 to 12 stations
S Kit
1 to 8 stations:
EX500
1 to 12 stations:
EX250
(
)
Applicable
solenoid
valves
5-station
weight
(g)
VQC100-5
628
(Single)
VQC101-5
VQC200-5
VQC201-5
759
(Double, 3P)
1051
(Single)
1144
(Double, 3P)
C8 (for ø8)
C10 (for ø10)
VQC4000
VV5QC41-
T Kit: Terminal block box
Side
S Kit: Serial transmission
P: Rc 1/2
C12 (for ø12)
R: Rc 3/4
Rc 1/4
Rc 3/8
Bottom
(1 to 10T Kitstations) VQC400-5
(1 to 16S Kitstations)
4150
• S Kit
(without unit)
VQC401-5 • Solenoid
weight is not
included.
Rc 1/4
Note 1) One-touch fittings in inch sizes are also available.
Note 2) An optional specification for special wiring is available to increase the maximum number of stations.
6
VQC1000/2000
S
Kit (Serial Transmission Kit) Decentralized Serial wiring
Conforms to IP67
00
EX5
Gateway type serial transmission system
• Since wiring is "prepackaged" into one multi-connector type cable, wiring work is not only made
easier, but much more accurate.
S Kit can be used by connecting to gateway unit.
Gateway (GW) Unit
Specifications
Model
Applicable PLC
Communication protocol
EX500-GAB1-X1
EX500-GDN1
EX500-GPR1
Rockwell⋅Automation PLC
DeviceNet Release 2.0
PROFIBUS-DP
57.6Kbit/sec, 115.2Kbit/sec 125Kbit/sec, 250Kbit/sec
500Kbit/sec
230.4Kbit/sec
Communication speed
Rated voltage
9.6, 19.2, 93.75, 187.5, 500Kbit/sec
1.5, 3, 6, 12Mbit/sec
24VDC
Input and control unit power supply: 24VDC ±10%
Power supply voltage range Solenoid valve power supply: 24VDC +10%/–5% (with power drop warning at approx. 20V)
Current consumption
Number of inputs/outputs
Number of input/output
branches
Branch cable
Branch cable length
Communication connector
Power connector
Ambient operating
temperature and humidity
Enclosure
Applicable standard
How to Order
EX500
G DN 1
Applicable GW unit
Communication protocol
DeviceNet
PROFIBUS-DP
Remote I/O (RIO)
DN
PR
AB
Nil
DeviceNet
PROFIBUS-DP
-X1
Remote I/O (RIO)
200mA or less
Maximum 64 inputs/64 outputs
4 branches (16 inputs/16 outputs per branch)
8-core heavy-duty cable
5m or less (total extension 10m or less)
M12 connector (8-pin, socket)
M12 connector (5-pin, plug)
+5° to +45°C at 35% to 85% RH (no condensation)
IP65
UL, CSA, CE
∗ Communication cables and communication connectors are sold separately.
Input Block
How to Order Input Manifold
EEX500
IB1
How to Order Input Block
E 8
EX500
1 station
1
⋅⋅⋅
Note) When ordering an input block manifold, enter the
Input manifold part no. + Input block part no.
together. The input block, end block and DIN rail
are included in the input manifold.
1
2
3
4
5
6
Stations
M8 connector
M12 connector
M8 and M12 mixed
⋅⋅⋅
E
T
M
8
8 stations
DeviceNet
Nil
PROFIBUS-DP
Remote I/O (RIO)
-X1
∗ With waterproof cap
Input block specifications
Current source type input block (PNP input block)
or
Current sink type input block (NPN input block)
Communication connector
Number of connection blocks
Block supply voltage
Block supply current
Current consumption
Applicable GW unit
DeviceNet
PROFIBUS-DP
Remote I/O (RIO)
Nil
Input block specifications
Short circuit protection
M8 connector, PNP specifications
M8 connector, NPN specifications
M12 connector, PNP specifications
M12 connector, NPN specifications
8-point integrated type, M8 connector, PNP specifications
8-point integrated type, M8 connector, NPN specifications
Applicable GW unit
-X1
Connection block
IE 1
Block type
Input unit specifications
Connector type
Current source type (PNP output)
or
Current sink type (NPN output)
Applicable sensor
M12 connector (8-pin, plug)
Sensor connector
Number of inputs
Rated voltage
Indication
Insulation
Sensor supply current
Maximum 8 blocks
24VDC
0.65A maximum
100mA or less (at rated voltage)
Operates at 1A Typ. (power supply cut)
GW unit reset by turning power OFF and back ON.
M8 connector (3-pin) or M12 connector (4-pin)
2 inputs/8 inputs (M8 only)
24VDC
Green LED
None
Maximum 30mA/Sensor
Cables
How to Order Cable with M12 Connector
EX500
AC 030
SSPS
Cable length
003
005
010
030
050
8
1
Terminal no.
2
6
5
Connections
EX500
Connector specifications
AP 050
Cable length
Socket side: Straight
Plug side: Straight
Socket side: Angle
SAPA
Plug side: Angle
010
050
SSPS
2 Brown
3 Green
4 Yellow
5 Gray
6 Pink
7 Blue
8 Shield
4
5
6
7
8
Socket connector
pin arrangement
7
1 White
1
4
0.3m
0.5m
1m
3m
5m
Cable
core wire colors
3 3 2
7
How to Order Power Cable with Connector
8
2
Terminal no.
1
7
3
5
1
2
2
4
6
4
5
Plug connector
pin arrangement
4
Connector specifications
S
A
Straight
Angle
Cable
core wire colors
Brown: 0V (solenoid valve power supply)
White: 24VDC +10%/-5% (solenoid valve power supply)
Blue: 0V (input and control power supply)
Black: 24VDC ±10% (input and control power supply)
Gray: PE
1
3
5
3
Socket connector
pin arrangement
1m
5m
S
Connections
VQC1000/2000
(12)
Plug-in Unit
(L4)
(L3)
L2
VV5QC11
S Kit (Serial Transmission Kit: EX500)
65
Base-Mounted Type
42.5
21
7
L1
P = 10.5
1.5
Indicator light
13
28
1.5
Manual override
(5.5)
(35)
66
75
Approx. 2
37.5
Approx. 9
93.5
SI UNIT
Series
EX 500
Mounting hole for 4-M4
Stations
D-side
M12
Female thread
1
2
3
4
5
6
7
8
U-side
n
2-C8
3(R) port
DIN rail clamp screw
62.5
60
0
25
40.5
M12
Male thread
7.5
9.5
18.5
(12)
(7.5)
1
20.5
2n-C3, C4, C6, M5
C3: ø3.2 One-touch fitting
P = 10.5
C4: ø4 One-touch fitting
C6: ø6 One-touch fitting
M5: M5 thread
2-C8
1(P) port
34
Formulas: L1 = 10.5n + 45, L2 = 10.5n + 93.5 n: Stations (maximum 16 stations)
L1
L2
L3
L4
2
66
114.5
137.5
148
3
76.5
125
150
160.5
4
87
135.5
162.5
173
5
97.5
146
175
185.5
6
108
156.5
187.5
198
7
118.5
167
187.5
198
8
129
177.5
200
210.5
9
139.5
188
212.5
223
VV5QC21
S Kit
11
160.5
209
237.5
248
12
171
219.5
250
260.5
13
181.5
230
250
260.5
38.5
76.5
13
P = 16
Indicator light
34.5
1
38.5
1
15
202.5
251
275
285.5
16
213
261.5
287.5
298
(5.5)
Manual override
(35)
80
105.5
(46.5)
Approx. 3.5
127
SI UNIT
Series
EX500
Mounting hole for 4-M5
D-side
Stations
1
2
3
4
5
6
7
8
n
U-side
C10
3(R) port
2-C12
3(R) port
DIN rail clamp screw
0
C10
1(P) port
2n-C4, C6, C8
C4: ø4 One-touch fitting
C6: ø6 One-touch fitting
C8: ø8 One-touch fitting
P = 16
25
45
13.5
(7.5)
(12)
25
30
49.5
1
10
76.5
60
14
192
240.5
262.5
273
(L4)
(L3)
L2
L1
(Serial Transmission Kit: EX500)
(12)
10
150
198.5
225
235.5
Approx. 10.5
L
1
55.5
104
125
135.5
Approx. 5.5
n
2-C12
1(P) port
Formulas: L1 = 16n + 57, L2 = 16n + 102 n: Stations (maximum 16 stations)
n
L
L1
L2
L3
L4
1
73
118
137.5
148
2
89
134
150
160.5
3
105
150
175
185.5
4
121
166
187.5
198
5
137
182
200
210.5
6
153
198
212.5
223
7
169
214
237.5
248
8
185
230
250
260.5
9
201
246
262.5
273
10
217
262
287.5
298
11
233
278
300
310.5
12
249
294
312.5
323
13
265
310
337.5
348
14
281
326
350
360.5
15
297
342
362.5
373
16
313
358
375
385.5
8
VQC1000/2000
S
Kit (Serial Transmission Kit) for I/O Conforms to IP67
Compatible network
DeviceNet/PROFIBUS-DP
• The serial transmission system greatly reduces connection work, minimizes wiring, and saves space.
DeviceNet/PROFIBUS compatible SI unit
Input block
As a DeviceNet/PROFIBUS slave unit, this kit is capable of solenoid valve
ON and OFF control up to 32 points.
Furthermore, by connecting an input block, a maximum 32 sensor signal
inputs are possible.
This expansion block connects to the SI unit and allows for sensor input to
the auto switches.
Each input block can receive input from up to two or four sensors, and the
common can be matched to the sensor by an NPN/PNP selector switch.
Input connectors are available in both M8 and M12 types.
Connector Details
Communication connector DeviceNet: M12, 5 pins (for plug and DeviceNet only)
Example of corresponding cable assemblies with connector:
OMRON Corporation DCA1-5CN05F1, Karl Lumberg GmbH & Co. KG RKT5-56
Input connector: M12, 5 pins (receptacle)
Cable side connector example: OMRON Corporation XS2G
2-input block (EX250-IE1)
4-input block (EX250-IE2)
No.
1
2
4
3
SW+
2∗
N.C. (SIGNAL) Open
4
5
(+) Sensor power supply
1
3
5
No.
Function
Description
5
SW–
(–) Sensor power supply
SIGNAL
Sensor input signal
Drain
Drain/Shield
3
2
2
V+
(+) Circuit power supply
4
1
3
V–
(–) Circuit power supply
4
CAN_H
Signal H
5
CAN_L
Signal L
Sensor ground
E
∗ In the case of 4-input block unit (EX250-IE2), this is
the sensor input signal.
Communication connector (PROFIBUS-DP): M12, 5 pins (plug)
5
R
0
0
0
0
BUS
1
3
1
1
X
2
3
P
3
4
No.
1
31
No.
5
(+) Sensor power supply
24V
3
0V
(–) Sensor power supply
4
IN
Sensor input signal
1
Description
Function
1
VP
Terminal +5V
2
R x D/T x D(N)
Signal –N
3
DGND
GND terminal
4
R x D/T x D(P)
Signal –P
5
SHIELD
Shield ground
Power connector: M12, 5 pins
(Boss configuration differs from plug and communication connector.)
Example of corresponding cable assemblies with connector:
Hans Turck FmbH & Co. KG SAKW4.5T-2.
Function
Description
2
4
PWR
1
Input connector: M8, 3 pins (receptacle)
Cable side connector example: Franz Binder GesmbH
718,768 series
4-input block (EX250-IE3)
3
No.
12
1
2
Function
Description
1
Description
Function
1
SV24V
For solenoid valve +24V
3
2
2
SV0V
For solenoid valve 0V
4
1
3
SW24V
For sensor unit +24V
4
SW0V
For sensor unit 0V
5
E
Ground
Indicator Unit (LED) Description and Function
Input block
SI unit (DeviceNet)
Function
Description
PWR(V) PWR
MOD/NET
1
PWR(V)
ON when solenoid valve power supply is turned ON.
PWR
ON when DeviceNet circuit power supply input is turned ON.
PWR
PWR
0
0
0
SETTINGS
1
OFF: Power supply off, off line, or when checking duplication of MAC_ID.
EX250
2
GREEN BLINKING: Waiting for connection (on line).
MOD/NET
1
3
GREEN ON: Connection established (on line).
EX250
EX250
RED BLINKING: Connection time out (minor communication abnormality).
RED ON: MAC_ID duplication error, or BUSOFF error
(major communication abnormality).
SI unit (PROFIBUS-DP)
Description
Function
Description
9
2-input type
(EX250-IE1)
PWR(V)
ON when solenoid valve power supply is turned ON.
OFF when the power supply voltage is less than 19V.
RUN
ON when operating (SI unit power supply is ON).
DIA
ON when the self diagnosis device detects abnormality.
BF
ON for BUS abnormality.
PWR
4-input type
(EX250-IE2/3)
Function
ON when sensor power is turned ON.
0 to 1(3) ON when each sensor input goes ON.
∗ Contact your SMC
representative for specifications
and handling precautions.
VQC1000/2000
VV5QC11
S Kit
(Serial Transmission Kit: EX250)
5.5
21
111
63
L1
P = 10.5 28
1.5
Indicator light
Manual override
Input block
Mounting hole for 6-M4
SI unit
D-side Stations
1
2
3
4
5
6
7
8
n
U-side
0
Approx. 2
37.5
Approx. 4
93.5
(5.5)
(35)
66
75
1.5
2-C8
3(R) port
DIN rail clamp screw
62.5
60
BUS
18.5
25
40.5
1
2
4-M8
2-M12
PWR
7.5
9.5
(7.5)
3
(12)
Plug-in Unit
(L4)
(L3)
L2
65
13
(12)
Base-Mounted Type
M3
2n-C3, C4, C6, M5
C3: ø3.2 One-touch fitting
P = 10.5
C4: ø4 One-touch fitting
C6: ø6 One-touch fitting
M5: M5 thread
20.5
34
2-C8
1(P) port
Formulas: L1 = 10.5n + 45, L2 = 10.5n + 167.5 (for 1 input block. For each additional input block, add 21mm.) n: Stations (maximum 24 stations)
2
3
4
5
6
66
76.5 87
97.5 108
188.5 199 209.5 220 230.5
212.5 225 237.5 250 250
223 235.5 248 260.5 260.5
7
8
118.5 129
241 251.5
262.5 275
273 285.5
9
139.5
262
287.5
298
10 11
150 160.5
272.5 283
300 312.5
310.2 323
12
171
293.5
325
335.5
13 14
181.5 192
304 314.5
325 337.5
335.5 348
VV5QC21
S Kit
(Serial Transmission Kit: EX250)
17 18
223.5 234
346 356.5
375 387.5
385.5 398
19
244.5
367
387.5
398
20 21 22
255 265.5 276
377.5 388 398.5
400 412.5 425
410.5 423 435.5
23
286.5
409
437.5
448
24
297
419.5
450
448
(L4)
(L3)
L2
5.5
21
76.5
(12)
15 16
202.5 213
325 335.5
350 362.5
360.5 373
107
63
L1
34.5
1
13
P = 16 38.5
1
Indicator light
(5.5)
127
(46.5)
Approx. 3.5
(35)
80
105.5
Manual override
Mounting hole
for 4-M5
D-side
76.5
60
C10
3(R) port
Stations
1
2
3
4
5
6
7
8
n
Approx. 10.5
L1
L2
L3
L4
1
55.5
178
200
210.5
U-side
Approx. 5.5
n
L
2-C12
3(R) port
DIN rail clamp screw
30
49.5
BUS
(12)
(7.5)
C10
1(P) port
2n-C4, C6, C8
C4: ø4 One-touch fitting
C6: ø6 One-touch fitting
C8: ø8 One-touch fitting
P = 16
25
45
13.5
25
10
PWR
2-C12
1(P) port
Formulas: L1 = 16n + 57, L2 = 16n + 176 (for 1 input block. For each additional input block, add 21mm.) n: Stations (maximum 24 stations)
n
L
L1
L2
L3
L4
1
73
192
212.5
223
2
3
89 105
208 224
237.5 250
248 260.5
4
5
121 137
240 256
262.5 275
273 285.5
6
153
272
287.5
298
7
8
169 185
288 304
312.5 325
323 335.5
9
201
320
337.5
348
10 11
217 233
336 352
362.5 375
373 385.5
12
249
368
387.5
398
13 14
265 281
384 400
400 425
410.5 435.5
15 16
297 313
416 432
437.5 450
448 460.5
17
329
448
462.5
473
18 19
345 361
464 480
487.5 500
498 510.5
20 21 22
377 393 409
496 512 528
512.5 537.5 550
523 548 560.5
23
425
544
562.5
573
24
441
560
587.5
598
10
VQC4000
S
Kit (Serial Transmission Kit) for I/O Conforms to IP67
Compatible network DeviceNet/PROFIBUS-DP
• The serial transmission system greatly reduces connection work, minimizes wiring, and saves space.
DeviceNet/PROFIBUS compatible SI unit
Input block
As a DeviceNet/PROFIBUS slave unit, this kit is capable of solenoid valve
ON and OFF control up to 32 points.
Furthermore, by connecting a maximum of 4 input blocks, up to 32 sensor
signal inputs are possible.
This expansion block connects to the SI unit and allows for sensor input to
the auto switches.
Each input block can receive input from up to 8 sensors, and the common
can be matched to the sensor by an NPN/PNP selector switch.
Connector Details
Input block
SI unit (DeviceNet)
• Communication connector (PROFIBUS-DP):
SI unit (PROFIBUS-DP)
CONINVERS® RC-2RS1N12, 12 pins
Cable side connector example: Siemens AG 6ES5 760-2CB11
Communication
connector
SI UNIT
PWR(V)
PWR
MOD/NET
No.
1
0
Function
Description
SETTINGS
Input connector
Power connector
9
1
12
2
6
4
1
M5V
GND Terminal
2
A
Signal –N
4
B
Signal –P
6
+5V
Terminal +5V
9
SHIELD
Shield ground
12
RTS
Optical fiber (reserve)
• Pin no. 3, 5, 7, 8, 10 and 11 marked with "" are open.
∗ The connector configuration and the pin arrangement are
compatible with Siemens AG ET200C.
• Input connector: M12, 5 pins (OMRON Corporation XS2F compatible) x 8 pcs.
Cable side connector example: OMRON Corporation XS2G
No.
2
1
3
4
5
1
SW +
Function
(+) Sensor power supply
2
N.C.
Open∗
3
SW –
(–) Sensor power supply
4
SIGNAL
Sensor input signal
5
PE
Protective sensor ground
Description
• Power connector: Franz Binder GesmbH Series723, 5 pins (72309-0115-80-05)
Cable side connector example: Franz Binder GesmbH 72309-0114-70-15, etc.
∗ DIN type 5 pins
4
5
∗ The second pin of the connector with input no. 0, 2, 4, 6 (the connector
at the right side of the input block) is connected internally to the fourth
pin (sensor input no.) of the connector with input no. 1, 3, 5, 7. This
makes it possible to directly input two inputs that are combined together
by the common connector.
Connector: Input no. 0, 2, 4, 6
SW +
1
SIGNAL -n + 1
2
SW–
3
SIGNAL -n
4
PE
5
No.
Description
Function
1
SV24V
For solenoid valve +24V
2
SV0V
For solenoid valve 0V
3
PE
Protective ground
4
SW24V
For solenoid valve +24V
5
SW0V
For solenoid valve 0V
3
2
1
• Communication connector (DeviceNet): M12, 5 pins (for DeviceNet only)
Input no. 1, 3, 5, 7
1
2
3
4
5
Example of corresponding cable assemblies with connector:
OMRON Corporation DCA1-5CN05F1, Karl Lumberg GmbH & Co. KG RKT5-56.
3
No.
Description
1
Drain
Drain/Shield
2
V+
(+) Circuit power supply
3
V–
(–) Circuit power supply
4
CAN_H
Signal H
5
CAN_L
Signal L
2
5
Caution
When IP65 or equivalent enclosures are required, install a waterproof
cover on the input connector that is not being used. Order waterproof
covers separately.
Example: OMRON Corporation XS2Z-12
4
Indicator Unit (LED) Descriptions and Functions
1
Function
Compatible with DeviceNet specification Micro
Style connector.
SI unit (PROFIBUS-DP)
SI unit (DeviceNet)
Input block
0
2
PWR 4
6
TM
PWR(V)
PWR(V)
PWR MOD/NET
RUN
1
3
5
7
ADDRESS
1
H
0
L
SETTINGS
DIA
FB
FB
PS
PS
Description
Function
PWR(V)
ON when solenoid valve power supply is turned ON.
PWR
ON when DeviceNet circuit power supply input is turned ON.
Description
Function
PWR(V)
OFF when the power supply voltage is less than 19V.
RUN
ON when operating (SI unit power supply is ON).
GREEN BLINKING: Waiting for connection (on line).
DIA
ON when self diagnosis device detects abnormality.
BF
ON for BUS abnormality.
RED BLINKING: Connection time out (minor communication abnormality).
RED ON: MAC_ID duplication error, or BUSOFF error
(major communication abnormality).
Description
Function
PWR
ON when sensor power is turned ON.
OFF when short circuit protection is working.
ON when solenoid valve power supply is turned ON.
OFF: Power supply off, off line, or when checking duplication of MAC_ID.
MOD/NET GREEN ON: Connection established (on line).
11
BF
0 to 7 ON when each sensor input goes ON.
VQC4000
Base-Mounted Type
Plug-in Unit
VV5QC41
S Kit (Serial Transmission Kit: EX240)
L2 (1 input block: 8 inputs)
14.5
(128.5)
L1
54
P = 25
65.5
A B
A B
A B
A
A
32
10
9
143
163
7
98.8
A B
6
9
Manual override
Min.0 to Max. 4
unit
(0 to 216mm)
143
6.5
Indicator light
A B
8
101
SI unit
Input block
Mounting hole for 2-M5, with input block only
D-side
Stations
1
2
3
4
5
8
n
U-side
2-Rc 1/4, 3/8, C8, C10, C12
(2(B), 4(A) port)
2-Rc 1/8
(External pilot port)
11.5
1.5
2-Rc 1/8
(Pilot EXH port)
21.5
27
31
38.5
43.5
77.5
95.5
12
20.5
75.5
23
61.5 8
2-Rc 3/4
3(R) port
2-Rc 1/2
1(P) port
(6.5)
Formulas: L1 = 25n + 106, L2 = 25n + 241 (for 1 input block. For each additional input block, add 54mm.) n: Stations (maximum 16 stations)
n
L
L1
L2
1
131
266
2
156
291
3
181
316
4
206
341
5
231
366
6
256
391
7
281
416
8
306
441
9
331
466
10
356
491
11
381
516
12
406
541
13
431
566
14
456
591
15
481
616
16
506
641
12
F
e
sid
U-
VQC1000/2000
Kit (D-sub Connector Kit) Conforms to IP40
• Using our D-sub connector for electrical connections greatly reduces labor,
while it also minimizes wiring and saves space.
• We use a D-sub connector (25P) that conforms to MIL standards and is
therefore widely compatible with many standard commercial models.
• Top or side entry for the connector can be changed freely, allowing for
changes even after mounting, to meet any changing needs for space.
Electrical wiring specifications
015
As the standard electrical wiring specification
used is for 12 stations or less, double wiring
(connected to SOL. A and SOL. B) is used for
the internal wiring of each station regardless
of valve and option types.
Mixed single and double wiring are available
as options.
Refer to special wiring specifications (options)
below.
1
2
3
4
5
6
7
8
9
10
11
12
13
e
sid
D-
Cable assembly
D-sub connector
14
15
16
17
18
19
20
21
22
23
24
25
12
AXT100-DS25- 030
050
D-sub connector cable assemblies can be ordered with manifolds.
Refer to manifold ordering.
Lead wire colors for
D-sub connector
cable assembly
terminal numbers
Cable
0.3mm² x 25 cores
O.D. ø1.4
Approx. ø10
Lead wire colors for
D-sub connector assemblies
015
Connector terminal no.
(AXT100-DS25- 030 )
SOL. A
Station 3
SOL. B
SOL. A
Station 4
SOL. B
SOL. A
Station 5
SOL. B
SOL. A
Station 6
SOL. B
SOL. A
Station 7
SOL. B
SOL. A
Station 8
2
(–)
(+)
Brown
None
15
(–)
(+)
Pink
Black
3
(–)
(+)
Red
None
16
(–)
(+)
Blue
White
4
(–)
(+)
Orange
None
17
(–)
(+)
Purple
None
5
(–)
(+)
Yellow
None
18
(–)
(+)
Gray
None
6
(–)
(+)
Pink
None
19
(–)
(+)
Orange
Black
7
20
(–)
(+)
Blue
None
(–)
(+)
Red
White
(+)
Purple
White
(–)
(+)
Brown
White
9
22
(–)
(–)
(+)
(+)
Gray
Pink
Black
Red
10
(–)
(+)
White
Black
23
(–)
(+)
Gray
Red
SOL. A
11
(–)
(+)
White
Red
SOL. B
24
(–)
(+)
Black
White
12
(–)
(+)
Yellow
Red
∗ When using a standard commercial
connector, use a type 25P female connector
conforming to MIL-C-24308.
25
(–)
(+)
White
None
∗ Cannot be used for transfer wiring.
13
(+)
Positive
COM
spec.
SOL. A
SOL. B
SOL. A
Station 12
Black
(–)
SOL. B
Station 11
None
Yellow
8
SOL. A
Station 10
Black
(+)
21
SOL. B
Station 9
(+)
(–)
SOL. B
COM
(–) Note) Orange
Negative
COM
spec.
Red
Note) When using the negative COM specification, use valves for negative COM.
Special wiring specifications (options)
(For 25P)
14
15
16
17
18
19
20
21
22
23
24
25
1
2
3
4
5
6
7
8
9
10
11
12
13
Mixed single and double wiring are available as
options. The maximum number of manifold stations
is determined by the number of solenoids. Count one
point for a single solenoid type and two points for a
double solenoid type. The total number of solenoids
(points) must not exceed 24.
COM
13
8
SOL. B
(–)
(2.4)
SOL. A
Station 2
1
14
16
SOL. B
Terminal
no.
1
2
3
Seal (length indication)
4
015
5
6
Molded cover
7
2-M2.6 x 0.45
8
SMC
9
Connector DB-25SF-N
10
manufactured by
Japan Aviation
11
Electronics Industry, Ltd.
55
12
Socket side
13
14⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅25
14
Terminal no.
15
16
1⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅13
17
47.04
18
19
20
21
D-sub connector cable assemblies (optional)
22
23
Cable
Note
Part no.
length (L)
24
25
AXT100-DS25-015
1.5m
Cable
AXT100-DS25-030
3m
0.3mm² x 25 cores
AXT100-DS25-050
5m
44
SOL. A
Dot
Lead wire
marking
color
L
050
Polarity
Terminal
no.
Station 1
ns
atio
⋅⋅st
⋅
⋅
⋅
⋅
⋅
⋅⋅
3⋅⋅⋅
Electrical characteristics
Item
Characteristic
Conductor resistance 65 or less
Ω/km, 20°C
Withstand pressure
V, 1 minute, AC
1000
Insulation resistance
MΩ/km, 20°C
5 or more
Note) The minimum bending
radius for D-sub connector
cables is 20mm.
Lead
wire
color
Black
Brown
Red
Orange
Yellow
Pink
Blue
Purple
Gray
White
White
Yellow
Orange
Yellow
Pink
Blue
Purple
Gray
Orange
Red
Brown
Pink
Gray
Black
White
Dot
marking
None
None
None
None
None
None
None
White
Black
Black
Red
Red
Red
Black
Black
White
None
None
Black
White
White
Red
Red
White
None
Some connector manufacturers:
• Fujitsu, Ltd.
• Japan Aviation Electronics Industry, Ltd.
• J.S.T. Mfg. Co., Ltd.
• HIROSE ELECTRIC CO., LTD.
VQC1000/2000
Base-Mounted Type
Plug-in Unit
(L4)
(L3)
L2
VV5QC11
51
L1
P = 10.5
65
13
Indicator light
28
1.5
1.5
Manual override
37.5
Approx. 2
Applicable connector: D-sub connector (25P)
(Conforms to MIL-C-24308)
66
75
(35)
93.5
(5.5)
(12)
Mounting hole for 4-M4
Manual release for
switching connector direction
D-side Stations
1
2
3
4
5
6
7
8
n
U-side
2-C8
3(R) port
25
40.5
9.5
(7.5)
(12)
62.5
60
35
18.5
7.5
DIN rail clamp screw
20.5
2n-C3, C4, C6, M5
C3: ø3.2 One-touch fitting
C4: ø4 One-touch fitting
C6: ø6 One-touch fitting
M5: M5 thread
P = 10.5
34
2-C8
1(P) port
Formulas: L1 = 10.5n + 45, L2 = 10.5n + 102 n: Stations (maximum 24 stations)
2
3
4
5
6
66
76.5 87
97.5 108
123 133.5 144 154.5 165
150 162.5 175 175 187.5
160.5 173 185.5 185.5 198
7
8
118.5 129
175.5 186
200 212.5
210.5 223
9
139.5
196.5
225
235.5
10 11
150 160.5
207 217.5
237.5 237.5
248 248
12
171
228
250
260.5
13 14
181.5 192
238.5 249
262.5 275
273 285.5
VV5QC21
15 16
202.5 213
259.5 270
287.5 300
298 310.5
17
223.5
280.5
300
310.5
18 19
234 244.5
291 301.5
312.5 325
323 335.5
20 21 22
255 265.5 276
312 322.5 333
337.5 350 362.5
348 360.5 373
23
286.5
343.5
375
385.5
24
297
354
375
385.5
(L4)
(L3)
L2
(5.5)
1
Approx. 3.5
50.5
(46.5)
127
(12)
L1
Indicator light
Manual override P = 16 38.5
1
34.5
C10
3(R) port
Stations
1
2
3
4
5
6
7
8
n
U-side
2-C12
3(R) port
DIN rail clamp screw
C10
1(P) port
2n-C4, C6, C8
C4: ø4 One-touch fitting
C6: ø6 One-touch fitting
C8: ø8 One-touch fitting
P = 16
25
45
13.5
(12)
(7.5)
35
25
10
30
49.5
76.5
60
Applicable connector: D-sub connector (25P)
(Conforms to MIL-C-24308)
Mounting hole for 4-M5
Release for switching connector direction
D-side
Approx. 10.5
47
76.5
13
Approx. 5.5
L1
L2
L3
L4
1
55.5
112.5
137.5
148
(35)
80
105.5
n
L
2-C12
1(P) port
Formulas: L1 = 16n + 57, L2 = 16n + 110.5 n: Stations (maximum 24 stations)
n
L
L1
L2
L3
L4
1
73
126.5
150
160.5
2
3
89 105
142.5 158.5
162.5 187.5
173 198
4
5
121 137
174.5 190.5
200 212.5
210.5 223
6
153
206.5
237.5
248
7
169
222.5
250
260.5
8
185
238.5
262.5
273
11
12
9
10
201 217 233 249
254.5 270.5 286.5 302.5
275 300 312.5 325
285.5 310.5 323 335.5
13
14
15
265 281 297
318.5 334.5 350.5
350 362.5 375
360.5 373 385.5
16
17
313 329
366.5 382.5
387.5 412.5
398 423
18 19
345 361
398.5 414.5
425 437.5
435.5 448
20 21
377 393
430.5 446.5
450 475
460.5 485.5
22
23
409 425
462.5 478.5
487.5 500
498 510.5
24
441
494.5
525
535.5
14
P
e
sid
U-
VQC1000/2000
Kit (Flat Ribbon Cable Kit) Conforms to IP40
• Using our flat ribbon cable for electrical connections greatly reduces
labor, while it also minimizes wiring and saves space.
• We use flat ribbon cables whose connectors (26P and 20P) conform
to MIL standards, and are therefore widely compatible with many
standard commercial models.
• Top or side entry for the connector can be changed freely, allowing
for changes even after mounting, to meet any changing needs for
space.
1
AXT100-FC 20
26 - 2
Flat ribbon cable connector
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Triangle mark indicator position
<20P>
Station 1
SOL. A
SOL. B
1
(–)
(+)
2
(–)
(+)
Station 2
SOL. A
SOL. B
3
(–)
(+)
4
(–)
(+)
Station 3
SOL. A
SOL. B
5
Station 4
SOL. A
SOL. B
Station 6
Station 7
Station 8
Station 9
Station 10
Station 11
Station 12
(15.6)
Terminal Polarity
no.
Terminal Polarity
no.
Station 5
Station 1
SOL. A
SOL. B
1
(–)
(+)
2
(–)
(+)
Station 2
SOL. A
SOL. B
3
(–)
(+)
4
(–)
(+)
(–)
(+)
(–)
(+)
(–)
(+) Station 3
5
6
SOL. A
SOL. B
6
(–)
(+)
7
(–)
(+)
(–)
(+)
(–)
(+) Station 4
7
8
SOL. A 9
SOL. B 10
SOL. A 11
SOL. B 12
SOL. A
13
SOL. B
14
SOL. A 15
SOL. B 16
SOL. A
SOL. B
(+)
(+)
(–)
(+)
(–)
(+) Station 5
(–)
(+)
(–)
(+)
(–)
(+)
(–)
(+) Station 6
(–)
(+)
(–)
(+)
(–)
(+)
(–)
(+) Station 7
(–)
(+)
(–)
(+)
(–)
(+)
(–)
(+) Station 8
8
SOL. A 9
SOL. B 10
SOL. A 11
SOL. B 12
SOL. A
13
SOL. B
14
SOL. A 15
SOL. B 16
(–)
(–)
(–)
(+)
SOL. A 17
SOL. B 18
SOL. A 19
SOL. B 20
(–)
(+)
(–)
(+)
(–)
(+) Station 9
SOL. A 17
SOL. B 18
(–)
(+)
(–)
(+)
COM
(–)
(+)
19
(+)
(–)
COM
SOL. A 21
SOL. B 22
SOL. A 23
SOL. B 24
(–)
(+)
20
(–)
(+)
(–)
(+)
(–)
(+)
COM
25
(+)
(–)
COM
26
(+)
(–)
Positive Negative
COM
COM
spec.
spec.
(+) (–)
Positive Negative
COM
COM
spec.
spec.
Note) When using the negative COM specification, use valves for negative COM.
L
Flat ribbon cable connector assemblies (optional)
Part no.
Cable
length (L)
26P
AXT100-FC26-1
AXT100-FC26-2
AXT100-FC26-3
1.5m
3m
5m
20P
AXT100-FC20-1
AXT100-FC20-2
AXT100-FC20-3
∗ When using a standard commercial connector, use a type 26P
connector conforming to MIL-C-83503 or a type 20P with strain relief.
∗ Cannot be used for transfer wiring.
Some connector manufacturers:
• HIROSE ELECTRIC CO., LTD.
• Sumitomo/3-M Limited
• Fujitsu, Ltd.
• Japan Aviation Electronics Industry, Ltd.
• J.S.T. Mfg. Co., Ltd.
• Oki Electric Cable Co., Ltd.
Special wiring specifications (options)
COM
COM
26
25
24
23
22
21
20
19
20
19
18
17
18
17
16
15
16
15
14
13
14
13
12
11
12
11
10
9
10
9
8
7
8
7
6
5
6
5
4
3
4
3
2
1
2
1
(For 26P)
15
28AWG
Red
Connector terminal number
<26P>
Terminal no.
6
1
19
18
25
21
20
2
23
22
Type 26P flat ribbon cable connector assemblies can be ordered
with manifolds. Refer to manifold ordering.
26
24
3
Double wiring (connected to SOL. A
and SOL. B) is used for the internal
wiring of each station regardless of
valve and option types.
Mixed single and double wiring are
available as options.
Refer to special wiring specifications (options) below.
30 (20P)
37.5 (26P)
25
ide
D-s
Cable assembly
Electrical wiring specifications
26
12
ns
atio
⋅⋅st
⋅
⋅
⋅
⋅
⋅
⋅⋅
3⋅⋅⋅
COM
COM
(For 20P)
Mixed single and double wiring are available as options.
The maximum number of
manifold stations is determined by the number of solenoids. Count one point for a
single solenoid type and two
points for a double solenoid
type. The total number of
solenoids (points) must not
exceed 24.
VQC1000/2000
VV5QC11
Base-Mounted Type
Plug-in Unit
(L4)
(L3)
L2
65
51
1.5
L1
P = 10.5
Indicator light
28
1.5
Manual override
37.5
Approx. 2
Stations
1
2
3
4
5
6
7
n
8
U-side
2-C8
3(R) port
DIN rail clamp screw
(7.5)
7.5
25
40.5
D-side
62.5
60
35
(12) 18.5
Mounting hole for 4-M4
Manual release for switching connector direction
2n-C3, C4, C6, M5
C3: ø3.2 One-touch fitting
P = 10.5
C4: ø4 One-touch fitting
C6: ø6 One-touch fitting
M5: M5 thread
9.5
Applicable connector:
Flat ribbon cable connector (26P)
(Conforms to MIL-C-83503 )
(35)
66
75
(5.5)
13
93.5
(12)
20.5
34
2-C8
1(P) port
Formulas: L1 = 10.5n + 45, L2 = 10.5n + 102 n: Stations (maximum 24 stations)
2
3
4
5
6
66
76.5 87
97.5 108
123 133.5 144 154.5 165
150 162.5 175 175 187.5
160.5 173 185.5 185.5 198
7
8
118.5 129
175.5 186
200 212.5
210.5 223
9
139.5
196.5
225
235.5
10 11
150 160.5
207 217.5
237.5 237.5
248 248
12
171
228
250
260.5
13 14
181.5 192
238.5 249
262.5 275
273 285.5
15 16
202.5 213
259.5 270
287.5 300
298 310.5
17
223.5
280.5
300
310.5
18 19
234 244.5
291 301.5
312.5 325
323 335.5
20 21 22
255 265.5 276
312 322.5 333
337.5 350 362.5
348 360.5 373
23
286.5
343.5
375
385.5
24
297
354
375
385.5
47
76.5
L1
P = 16
Indicator light
34.5
1
38.5
1
Manual override
(5.5)
13
Applicable connector:
Flat ribbon cable connector (26P)
(Conforms to MIL-C-83503 )
(35)
Approx. 3.5
50.5
(46.5)
127
(12)
Manual release for switching connector direction
D-side
Stations
1
2
3
4
5
6
7
8
Mounting hole for 4-M5
n
Approx. 10.5
(L4)
(L3)
L2
VV5QC21
Approx. 5.5
L1
L2
L3
L4
1
55.5
112.5
137.5
148
80
105.5
n
L
U-side
C10
3(R) port
2-C12
3(R) port
30
49.5
C10
1(P) port
2n-C4, C6, C8
C4: ø4 One-touch fitting
C6: ø6 One-touch fitting
C8: ø8 One-touch fitting
P = 16
25
45
13.5
10
(12)
(7.5)
35
25
76.5
60
DIN rail clamp screw
2-C12
1(P) port
Formulas: L1 = 16n + 57, L2 = 16n + 110.5 n: Stations (maximum 24 stations)
n
L
L1
L2
L3
L4
1
73
126.5
150
160.5
2
3
89 105
142.5 158.5
162.5 187.5
173 198
4
5
121 137
174.5 190.5
200 212.5
210.5 223
6
153
206.5
237.5
248
7
8
169 185
222.5 238.5
250 262.5
260.5 273
9
201
254.5
275
285.5
10 11
217 233
270.5 286.5
300 312.5
310.5 323
12
249
302.5
325
335.5
13 14
265 281
318.5 334.5
350 362.5
360.5 373
15 16
297 313
350.5 366.5
375 387.5
385.5 398
17
329
382.5
412.5
423
18 19
345 361
398.5 414.5
425 437.5
435.5 448
20 21 22
377 393 409
430.5 446.5 462.5
450 475 487.5
460.5 485.5 498
23
425
478.5
500
510.5
24
441
494.5
525
535.5
16
T
VQC1000/2000/4000
Kit (Terminal Block Box Kit) Conforms to IP67
• This kit has a small terminal block inside a junction box. The provision of
a G3/4 electrical entry allows connection of conduit fittings.
Terminal Block Connection
Step 2. The diagram below shows the terminal block wiring.
All stations are provided with double wiring
regardless of the valves which are mounted.
Connect each wire to the power supply side, according
to the markings provided inside the terminal block.
Step 1. How to remove terminal block cover
Loosen the 4 mounting screws (M4) and remove the
terminal block cover.
Terminal block cover
Mounting screw (M4)
M3 screw
Gasket
m
6m
Electrical entry
2-G3/4
Step 3. How to replace the terminal block cover
Securely tighten the screws to the torque shown in the
table below, after confirming that the gasket is installed
correctly.
• Applicable crimp terminal (fork tongue type): 1.25-3S, 1.25Y-3
1.25Y-3N, 1.25Y-3.5
Proper tightening torque (N⋅m)
0.7 to 1.2
Electrical wiring specifications (conforms to IP67)
Special wiring specifications (options)
Standard wiring
Terminal
no.
SOL. A
1B
1A
SOL. B
SOL. A
3B
Station 2
SOL. B
Station 4
SOL. B
SOL. A
9B 10B
9A 10A COM
8B
8A
Station 3
7B
6A 7A
5B 6B
5A
SOL. A
4B
3A 4A
2B
2A
1B 2B 3B 4B 5B 6B 7B 8B 9B 10B
1A 2A 3A 4A 5A 6A 7A 8A 9A 10A COM
Station 1
SOL. B
SOL. A
Station 5
SOL. B
SOL. A
Station 6
SOL. B
SOL. A
SOL. B
SOL. A
Station 8
SOL. B
Station 9
SOL. B
SOL. A
Station 10
SOL. B
(–)
(+)
1B
(–)
(+)
2A
(–)
(+)
2B
(–)
(+)
3A
(–)
(+)
1. How to order
3B
(–)
(+)
4A
(–)
(+)
4B
(–)
(+)
5A
(–)
(+)
Indicate option symbol "-K" in the manifold part
number and be sure to specify station positions for
single or double wiring on the manifold specification
sheet.
5B
(–)
(+)
2. Wiring specifications
6A
(–)
(+)
6B
(–)
(+)
7A
(–)
(+)
7B
(–)
(+)
Connector terminal numbers are connected from
solenoid station 1 on the A side in the order
indicated by the arrows without skipping any
terminal numbers.
8A
(–)
(+)
8B
(–)
(+)
9A
(–)
(+)
9B
(–)
(+)
10A
(–)
(+)
10B
(–)
(+)
COM
(+)
(–)
Positive Negative
COM
COM
17
1B 2B 3B 4B 5B 6B 7B 8B 9B 10B
SOL. A
1A
1A 2A 3A 4A 5A 6A 7A 8A 9A 10A COM
Note) There is no polarity. This device can also be used as a
negative common.
Station 7
Mixed single and double wiring are available as
options. The maximum number of manifold stations
is determined by the number of solenoids. Count
one point for a single solenoid type and two points
for a double solenoid type. The total number of
solenoids (points) must not exceed 20.
1B 2B 3B 4B 5B 6B 7B 8B 9B 10B
1A 2A 3A 4A 5A 6A 7A 8A 9A 10A COM
The internal wiring is double (connected to SOL. A and SOL. B) for
all stations regardless of the type
of valve or options.
Mixed single and double wiring
are available as options.
Polarity
VQC1000/2000
Base-Mounted Type
(L4)
(L3)
L2
VV5QC11
Indicator light
13
L1
P = 10.5
7
Manual override
28
1.5
Approx. 2
(35)
66
75
126
80
(5.5)
1.5
93.5
103
(12)
Plug-in Unit
2-G3/4
D-side
Conduit port
Stations
1
2
3
4
5
6
7
n
8
Mounting hole for 4-M4
U-side
2-C8
3(R) port
9.5
2n-C3, C4, C6, M5
C3: ø3.2 One-touch fitting
C4: ø4 One-touch fitting
C6: ø6 One-touch fitting
M5: M5 thread
(7.5)
(12)
25
40.5
7.7
77.7
18.7
DIN rail clamp screw
20.5
34
P = 10.5
2-C8
1(P) port
Formulas: L1 = 10.5n + 45, L2 = 10.5n + 154.5 n: Stations (maximum 20 stations)
n
L
L1
L2
L3
L4
4
5
1
2
3
55.5 66
76.5 87
97.5
165 175.5 186 196.5 207
187.5 200 212.5 212.5 225
198 210.5 223 223 235.5
6
108
217.5
237.5
248
7
118.5
228
250
260.5
8
129
238.5
262.5
273
9
139.5
249
275
285.5
10
150
259.5
275
285.5
11
160.5
270
287.5
298
12
171
280.5
300
310.5
13
181.5
291
312.5
323
99
76.5
7
13
16
213
322.5
337.5
348
17
223.5
333
350
360.5
18
234
343.5
362.5
373
19
244.5
354
375
385.5
20
255
364.5
387.5
398
L1
P = 16
1
Manual override
38.5
1
2-G3/4
Conduit port
(35)
80
105.5
Approx. 5.5
Approx. 3.5
(46.5)
127
80
(5.5)
Approx. 10.5
(12)
15
202.5
312
337.5
348
Indicator light
(L4)
(L3)
L2
VV5QC21
14
192
301.5
325
335.5
C10
3(R) port
D-side
Stations
1
2
3
4
5
6
7
8
n
U-side
Mounting hole for 4-M5
2-C12
3(R) port
C10
1(P) port
2n-C4, C6, C8
C4: ø4 One-touch fitting
C6: ø6 One-touch fitting
C8: ø8 One-touch fitting
P = 16
25
45
13.5
12
(7.5)
25
10
30
49.5
77.5
DIN rail clamp screw
2-C12
1(P) port
Formulas: L1 = 16n + 57, L2 = 16n + 163 n: Stations (maximum 20 stations)
n
L
L1
L2
L3
L4
1
2
73
89
179 195
200 212.5
210.5 223
3
105
211
237.5
248
4
121
227
237.5
248
5
137
243
262.5
273
6
153
259
262.5
273
7
169
275
287.5
298
8
185
291
312.5
323
9
201
307
325
335.5
10
217
323
371
360.5
11
233
339
362.5
373
12
249
355
375
385.5
13
265
371
408.5
398
14
281
387
412.5
423
15
297
403
425
435.5
16
313
419
437.5
448
17
329
435
462.5
473
18
345
451
496
485.5
19
361
467
487.5
498
20
377
483
500
510.5
18
T
VQC1000/2000/4000
Kit (Terminal Block Box Kit) Conforms to IP67
VV5QC41
L2
6.5
L1
P = 25
Indicator light
Manual override
4
5
6
7
9
3
65.5
A
A
9
34.5
80
143
A B
A B
A B
A B
A B
7
163
79.5
Mounting hole
for 2-M5
101
D-side
Stations
1
2
8
n
U-side
2-Rc 3/4
3(R) port
2-Rc 1/4, 3/8, C8, C10, C12
(2(B), 4(A) port)
11.5
2-Rc 1/8
(External pilot port)
12
20.5
43.5
77.5
95.5
2-Rc 1/2
1(P) port
2-Rc 1/8
(Pilot EXH port)
21.5
(6.5)
27
31
38.7
Formulas: L1 = 25n + 106, L2 = 25n + 192 n: Stations (maximum 20 stations)
n
L
L1
L2
19
1
131
217
2
156
242
3
181
267
4
206
292
5
231
317
6
256
342
7
281
367
8
306
392
9
331
417
10
356
442
11
381
467
12
406
492
13
431
517
14
456
542
15
481
567
16
506
592
17
531
617
18
556
642
19
581
667
20
606
692
20
Manifold Exploded View
Housing assembly and SI unit
VQC1000
VQC2000
D-side end plate assembly
Manifold block assembly
U-side end plate assembly
q
EX250
w
e
S Kit (Serial)
EX500
VQC1000
VQC2000
r
Çì
ÇÖ
0
Çâ
50
EX ÇÖÇí
Çì
!2
VQC4000
y
t
EX240
!3
!1
u
F Kit
(D-sub connector)
VQC1000
VQC2000
i
P Kit
(Flat ribbon cable)
VQC1000
VQC2000
T Kit
21
(Terminal block)
o
VQC1000
VQC2000
VQC4000
!0
Note) Drawing shows VQC1000 type.
VQC
Base-Mounted Type
Manifold Exploded View
Manifold Assembly Part No.
Housing assembly and SI unit/Input block
1
2
3
4
Part no.
Description
No.
EX250-SDN1
EX250-SPR1
EX250-IE1
EX250-IE2
EX250-IE3
EX250-EA
EX500-Q001
EX500-Q001-X1
EX500-Q101
EX500-Q101-X1
EX240-SDN2
EX240-SPR1
EX240-IE1
EX240-EA2
EX240-EA4
VVQC1000-F25-1
VVQC1000-P26-1
VVQC1000-P20-1
VVQC1000-T0-1
SI unit
Input block
End plate assembly
SI unit
5
SI unit
6
Input block
7
End cover assembly
8
D-sub connector housing assembly
9
Flat ribbon cable housing assembly
10
Terminal block box housing assembly
D-side end plate assembly
VQC1000
VQC2000
VQC4000
—
Remote I/O (–COM)
—
DeviceNet (+COM)
—
—
PROFIBUS-DP (–COM)
—
—
M12, 8 inputs
—
—
—
—
F Kit, 25-pin
—
P Kit, 26-pin
—
DeviceNet (–COM)
PROFIBUS-DP (–COM)
M12, 2 inputs
M12, 4 inputs
M8, 4 inputs
1: Standard 2: DIN rail mounting
DeviceNet ( +COM)
Remote I/O (+COM)
DeviceNet (–COM)
For manifold with input block
For manifold without input block
P Kit, 20-pin
T Kit
C8
C10
N9
N11
Wiring
specification
Options
Port size
VQC1000
VQC2000
VQC1000 VQC2000
Nil
R
S
Centralized exhaust
External pilot
Direct exhaust outlet
with built-in silencer
1
2
4
Thread type
F
T
S Kit
T Kit
VQC1000/2000
VVQC 1 000-2A-- 1 -- C8 --
Supply/Exhaust port
entry direction
1
Front
2 Note) Front and back
Note) VQC2000 only
Options
Nil
Port size
Symbol VQC1000
C8
C10
C12
N9
N11
N13
None
With back pressure
B Note) check valve
Note) Except for VQC4000.
VQC1000
VQC2000
VQC4000
Port size
Rc
G
NPT/NPTF
!2 U-side end plate assembly part no.
1 VQC1000
2 VQC2000
—
Note) Tie-rods (2 pcs.)
for additional stations included.
U-side end plate assembly
Series
—
Nil
Series
VVQC4000-3A-- 1
Kit type
—
Options
D Double wiring
S Single wiring
VQC4000
1
2
—
VVQC 1 000-1A-- D -- C6 --
VVQC 1 000-3A-1-- C8 --
1
2
—
!3 Manifold block assembly part no.
VQC1000/2000
Symbol
—
Manifold block assembly
!1 D-side end plate assembly part no.
Series
Applicable model
Note
VQC2000
Note)
Note)
R
S
Centralized exhaust
External pilot
Direct exhaust outlet
with built-in silencer
Symbol
Port size
C3
C4
C6
C8
C10
C12
N1
N3
N7
N9
N11
M5
02
03
B
ø3.2 One-touch fitting
ø4 One-touch fitting
ø6
ø8
ø10
ø12
ø1/8"
ø5/32"
ø1/4"
ø5/16"
ø3/8"
M5 thread
Rc 1/4"
Rc 3/8"
Rc 1/4" bottom ported
VQC1000 VQC2000
VQC4000
Note) For supply/exhaust port with
front and back entry type only.
VQC4000
VVQC4000-2A-- 1
Thread type
Nil
F
T
Rc
G
NPT/NPTF
22
Manifold Specification Sheet
Series VQC1000: Base-Mounted Type/Plug-in Unit
q How to order manifolds
VV5QC 1 1
08
C6 FD1
1
VV5QC 1 1
2
08
B
3
F/P/T
⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅
S Kit
Kit
8
C6 SDQ
B
4
Series VQC1000
⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅
5
6
7
⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅Fill out for I/O serial kit only.
Base-Mounted plug-in
01
i Options
3 Electrical entry/Cable length
1 Stations
1 station
The maximum number of stations
differs depending on the electrical
entry. Refer to e.
F Kit
⋅⋅⋅
⋅⋅⋅
D-side
entry
L3
Top ported elbow
Wtih ø3.2 One-touch fitting
L4
Top ported elbow
With ø4 One-touch fitting
L6
Top ported elbow
With ø6 One-touch fitting
T Kit
With ø3.2 One-touch fitting
With ø4 One-touch fitting
With ø6 One-touch fitting
M5 thread
Mixed sizes and with port plug
S Kit
C3
C4
C6
M5
CM
P Kit
2 Cylinder port size
D-sub connector kit (25P) without cable
D-sub connector kit (25P) with 1.5m cable
D-sub connector kit (25P) with 3.0m cable
D-sub connector kit (25P) with 5.0m cable
Flat ribbon cable kit (26P) without cable
Flat ribbon cable kit (26P) with 1.5m cable
Flat ribbon cable kit (26P) with 3.0m cable
Flat ribbon cable kit (26P) with 5.0m cable
Flat ribbon cable kit (20P) without cable Note 1)
Terminal block box kit
Input/Output serial kit (EX250)
Serial kit without SI unit
Serial kit DeviceNet compatible
Serial kit PROFIBUS-DP compatible
Decentralized wiring serial kit (EX500)
Serial kit for Remote I/O
Serial kit DeviceNet/PROFIBUS-DP compatible
SD0
SDQ
SDN
SDA1
SDA2
L5 M5 thread
Bottom ported elbow
B3
With ø3.2 One-touch fitting
FD0
FD1
FD2
FD3
PD0
PD1
PD2
PD3
PDC
TD0
K
N
R
S
1 to 12 (24)
1 to 9 (18)
1 to 12 (24)
1 to 8 (16)
Bottom ported elbow
With ø4 One-touch fitting
B6
Bottom ported elbow
With ø6 One-touch fitting
r SI unit COM
t Input block (Fill out for I/O unit only)
EX250
EX500
DeviceNet PROFIBUS-DP DeviceNet PROFIBUS-DP Remote I/O
—
+COM
—
–COM
SI unit COM
Nil
N
Nil
0
1
u Input block COM (Fill out for I/O unit only)
Nil
N
NPN (–)
8
Without SI unit/input block (SD0)
Without input block
With 1 input block
⋅⋅⋅⋅⋅⋅⋅
⋅⋅⋅⋅⋅⋅⋅
Note) Leave the box blank for the SI unit COM without input block (SD0).
PNP (+)
or without SI unit/input block (SD0)
None
All stations with back pressure check valve Note 1)
With DIN rail (rail length: standard)
With DIN rail (rail length: special) Note 2)
Special wiring specifications Note 3)
(except for double wiring)
With name plate
External pilot Note 4)
Direct exhaust with built-in silencer Note 5)
∗ When specifying two or more options, list symbols
in alphabetical order.
Example: -BRS
Note 1) When using the back pressure check valve
for the necessary stations only, enter the
back pressure check valve part no. and
indicate the number of manifold stations in
the specification sheet.
Note 2) For special DIN rail length, indicate "D."
(Enter the number of stations inside ).
Example: -D08
In this case, stations will be mounted on a
DIN rail for 8 stations regardless of the
actual number of manifold stations.
Indicate "-D0" for the option without DIN rail.
Note 3) Be sure to indicate the wiring specifications
in the specification sheet.
Note 4) For external pilot option, "-R", indicate the
external pilot specification "R" for the
applicable valves as well.
Note 5) The built-in silencer type does not satisfy the
IP67 standard.
1 to 10 (20)
B4
Note 1) Indicate the size in the
specification sheet in
the case of CM and LM.
Note 2) Symbols for inch sizes are
as follows:
<For One-touch fittings>
N1: ø1/8"
N3: ø5/32"
N7: ø1/4"
NM: Mixed
The top ported elbow is LN and
the bottom ported elbow is BN.
B
D
D
1 to 12 (24)
Note 1) P Kit: Order the cable assembly separately for the type 20P.
Note 2) Numbers inside ( ) indicate the maximum number of solenoids for mixed single and
double wiring. The maximum number of stations is determined by the total number of
solenoids. In the case of mixed wiring, use the option symbol "-K".
B5 M5 thread
LM Elbow port, mixed sizes
Nil
Stations Note 2)
Kit, Cable length
With 8 input blocks
y Input block type
(Fill out for I/O unit only)
Nil
1
2
3
w How to order applicable valves
Without input block
M12, 2 inputs
M12, 4 inputs
M8, 4 inputs (3 pins)
VQC 1 1 0 0 Y 5 E B
Series VQC1000
A
A Type of actuation
B
C
0
1
3
3-position closed center
C Function
4
5
A Note)
B Note)
C Note)
3-position exhaust center
Nil
K Note 1)
N
R
Y
Dual 3-port valve (N.C. + N.C.)
Dual 3-port valve (N.O. + N.O.)
Dual 3-port valve (N.C. + N.O.)
Note) Available for the rubber seal type only.
23
F
Metal seal
Rubber seal
2-position single
3-position pressure center
E
B Seal type
1
2
2-position double
D
Standard type (1W)
High voltage type (1.0MPa)
Negative COM
External pilot
Low wattage type (0.5W)
Note 1) Available for the metal seal type only.
∗ Wnen specifying two or more options, list
symbols in alphabetical order.
D Coil voltage
5
24VDC
E Light/Surge voltage
suppressor
D-side Stations⋅⋅⋅⋅1⋅⋅⋅⋅2⋅⋅⋅⋅⋅3⋅⋅⋅⋅4⋅⋅⋅⋅5⋅⋅⋅⋅6⋅⋅⋅⋅7⋅⋅⋅⋅8⋅⋅⋅⋅⋅⋅n U-side
∗ Stations are numbered in ascending order
from the D-side.
F Manual override
Nil
With
Nil
E
Without Note)
B
C
Note) Not applicable to S Kit.
Non-locking push type (tool required)
Slotted locking type (tool required)
Locking type (manual)
For ordering: Please copy this page and use it as often as necessary.
Manifold Specification Sheet
Series VQC1000/Plug-in Unit
Date:
Manifold Model
/
/
Customer name
Fill out for S Kit only
Contact person
VV5QC 1 1
Specification sheet no.
Purchase order no.
Kit type
Equipment name
Base-Mounted plug-in
Series VQC1000
Quantity
← D-side
Specifications
Stations
Description/Model
1
set(s) Required date
∗ Indicate required stations with a "".
2
3
4
5
6
7
8
9
U-side
→
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
A B
Single
EA PEB
A B
Double
EA P EB
A B
Closed center
Valves
EA P EB
A B
Exhaust center
EA P EB
A B
Pressure center
4
Dual 3-port valve
(A)
Dual 3-port valve
(B)
Dual 3-port valve
(C)
Blanking plate
EA P EB
2
5
N.C.
4
1
5
N.O.
4
1
5
N.C.
1
3
N.C.
2
3
N.O.
2
3
N.O.
VVQ1000-10A-1
Individual SUP spacer
Options
VVQ1000-P-1-C6
SUP shutoff position: Specify 2 positions.
Individual EXH spacer
VVQ1000-R-1-C6
EXH shutoff position: Specify 2 positions.
SUP block plate
VVQ1000-16A
EXH shutoff position Note 1)
using EXH block base
(When
VVQC1000-19A--C )
Cylinder port sizes Note 3)
Fill out in case of mixed sizes (CM/LM/NM).
Port plug Note 2)
A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B
With ø3.2 (ø1/8")
One-touch fitting
C3
Side port
(N1)
With ø4 (ø5/32")
One-touch fitting
Side port
C4
(N3)
With ø6 (ø1/4")
One-touch fitting
Side port
C6
(N7)
M5 thread
Side port M5
Dual flow fitting
VVQ1000-52A-C8
Special wiring Note 4)
specifications
Single wiring
Double wiring
Notes
Description/Model
Stations
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Note 1) Indicate the shutoff position. The D-side of the EXH block in the EXH passage is blocked.
Note 2) When using port plugs, circle ports to specify.
C3
C3
C6
C6
Note 3) When mounting an elbow fitting assembly (VVQ1000-F-L- C4), indicate "L C4" in the table above.
Note 4) In case of single wiring or mixed wiring, connections to the connector terminals start from the A-side solenoid of station 1 and continue in order without
skipping any terminals.
For SMC use only
Applicable valves and options
Part no.
Qty.
Part no.
Qty.
Order no.
Clerk (code no.)
Dept. code
24
Manifold Specification Sheet
Series VQC2000: Base-Mounted Type/Plug-in Unit
q How to order manifolds
VV5QC 2 1
08
C8 FD1
1
VV5QC 2 1
2
08
B
3
F / P / T Kit
⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅
S Kit
8
C8 SDQ
B
4
Series VQC2000
⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅
5
6
7 ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅Fill out for I/O serial kit only.
Base-Mounted plug-in
e Electrical entry/Cable length
q Stations
01
1 station
F Kit
⋅⋅⋅
⋅⋅⋅
The maximum number of stations
differs depending on the electrical
entry. Refer to e.
L4
Top ported elbow
With ø4 One-touch fitting
L6
Top ported elbow
With ø6 One-touch fitting
L8
Top ported elbow
With ø8 One-touch fitting
B4
Bottom ported elbow
With ø4 One-touch fitting
Bottom ported elbow
B6
With ø6 One-touch fitting
Bottom ported elbow
B8
With ø8 One-touch fitting
T Kit
With ø4 One-touch fitting
With ø6 One-touch fitting
With ø8 One-touch fitting
Mixed or with port plug
S Kit
C4
C6
C8
CM
P Kit
w Cylinder port size
i Options
D-side
entry
Kit, Cable length
FD0
FD1
FD2
FD3
PD0
PD1
PD2
PD3
PDC
TD0
D-sub connector kit (25P) without cable
D-sub connector kit (25P) with 1.5m cable
D-sub connector kit (25P) with 3.0m cable
D-sub connector kit (25P) with 5.0m cable
Flat ribbon cable kit (26P) without cable
Flat ribbon cable kit (26P) with 1.5m cable
Flat ribbon cable kit (26P) with 3.0m cable
Flat ribbon cable kit (26P) with 5.0m cable
Flat ribbon cable kit (20P) without cable Note 1)
Terminal block box kit
SD0
SDQ
SDN
SDA1
SDA2
Stations
Input/Output serial kit (EX250)
Serial kit without SI unit
Serial kit DeviceNet compatible
Serial kit PROFIBUS-DP compatible
Decentralized wiring serial kit (EX500)
Serial kit for Remote I/O
Serial kit DeviceNet/PROFIBUS-DP compatible
K
N
R
S
1 to 12 (24)
1 to 9 (18)
1 to 10 (20)
1 to 12 (24)
1 to 8 (16)
Note 1) P Kit: Order the cable assembly separately for type 20P.
Note 2) Numbers inside ( ) indicate the maximum number of solenoids for mixed single and
double wiring. The maximum number of stations is determined by the total number of
solenoids. In the case of mixed wiring, use the option symbol "-K".
r SI unit COM
N
t Input block (Fill out for I/O unit only)
EX250
EX500
DeviceNet PROFIBUS-DP DeviceNet PROFIBUS-DP Remote I/O
—
+COM
—
–COM
Nil
0
1
The top ported elbow is LN and
the bottom ported elbow is BN.
PNP (+)
or without SI unit/input block (SD0)
N
NPN (–)
⋅⋅⋅⋅⋅⋅⋅
u Input block COM (Fill out for I/O unit only)
Without SI unit/input block (SD0)
Without input block
With 1 input block
⋅⋅⋅⋅⋅⋅⋅
Note) Leave the box blank for the SI unit COM without input block (SD0).
Nil
Special wiring specifications Note 3)
(except for double wiring)
With name plate
External pilot Note 4)
Direct exhaust with built-in silencer Note 5)
∗ When specifying two or more options, list symbols
in alphabetical order.
Example: -BRS
Note 1) When using the back pressure check valve
for the necessary stations only, enter the
back pressure check valve part no. and
indicate the number of manifold stations in
the specification sheet.
Note 2) For special DIN rail length, indicate "D."
(Enter the number of stations inside .)
Example: -D08
In this case, stations will be mounted on a
DIN rail for 8 stations regardless of the actual
number of manifold stations.
Indicate "-D0" for the option without DIN rail.
Note 3) Be sure to indicate the wiring specifications
in the specification sheet.
Note 4) For external pilot option, "-R", indicate the
external pilot specification "R" for the
applicable valves as well.
Note 5) The built-in silencer type does not satisfy the
IP67 standard.
SI unit COM
Nil
None
B All stations with back pressure check valve Note 1)
D With DIN rail (rail length: standard)
D With DIN rail (rail length: special) Note 2)
1 to 12 (24)
LM Elbow port, mixed sizes
Note 1) Indicate the size in the
specification sheet in the
case of CM and LM.
Note 2) Symbols for inch sizes are
as follows:
<For One-touch fittings>
N3: ø5/32"
N7: ø1/4"
N9: ø5/16"
NM: Mixed
Nil
Note 2)
8
With 8 input blocks
y Input block type
(Fill out for I/O unit only)
Nil
1
2
3
w How to order applicable valves
Without input block
M12, 2 inputs
M12, 4 inputs
M8, 4 inputs (3 pins)
VQC 2 1 0 0 Y 5 E B
Series VQC2000
A
A Type of actuation
1
2
3
4
5
A Note)
B Note)
C Note)
2-position single
2-position double
3-position closed center
3-position exhaust center
3-position pressure center
Dual 3-port valve (N.C. + N.C.)
Dual 3-port valve (N.O. + N.O.)
Dual 3-port valve (N.C. + N.O.)
Note) Available for the rubber seal type only.
25
B
C
D E
F
B Seal type
0
1
Metal seal
Rubber seal
D Coil voltage
5
24VDC
E Light/Surge voltage
C Function
Nil
K Note 1)
N
R
Y
Standard type (1W)
High voltage type (1.0MPa)
Negative COM
External pilot
Low wattage type (0.5W)
Note 1) Available for the metal seal type only.
∗ When specifying two or more options,
list symbols in alphabetical order.
suppressor
Nil
E
With
Without Note)
Note) Not applicable to S Kit.
D-side Stations⋅⋅⋅⋅1⋅⋅⋅⋅2⋅⋅⋅⋅3⋅⋅⋅⋅⋅4⋅⋅⋅⋅5⋅⋅⋅⋅⋅6⋅⋅⋅⋅7⋅⋅⋅⋅8⋅⋅⋅⋅n U-side
∗ Stations are numbered in ascending order
from the D-side.
F Manual override
Nil
B
C
Non-locking push type (tool required)
Slotted locking type (tool required)
Locking type (manual)
For ordering: Please copy this page and use it as often as necessary.
Manifold Specification Sheet
Series VQC2000/Plug-in Unit
Date:
Manifold Model
/
/
Customer name
Fill out for S Kit only
Contact person
VV5QC 2 1
Specification sheet no.
Purchase order no.
Kit type
Base-Mounted plug-in
Series VQC2000
Equipment name
← D-side
Specifications
Stations 1
Description/Model
set(s) Required date
Quantity
∗ Indicate required stations with a "".
2
3
4
5
6
7
8
9
U-side
→
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
A B
Single
EA PEB
A B
Double
EA P EB
A B
Closed center
Valves
EA P EB
A B
Exhaust center
EA P EB
A B
Pressure center
4
Dual 3-port valve
(A)
5
N.C.
4
1
5
N.O.
4
1
5
N.C.
1
Dual 3-port valve
(B)
Dual 3-port valve
(C)
EA P EB
2
3
N.C.
2
3
N.O.
2
3
N.O.
Blanking plate
VVQ2000-10A-1
Individual SUP spacer
Options
VVQ2000-P-1-C8
SUP shutoff position: Specify 2 positions.
Individual EXH spacer
VVQ2000-R-1-C8
EXH shutoff position: Specify 2 positions.
SUP block plate
VVQ2000-16A
EXH block plate
VVQ2000-19A
Cylinder port sizes
Fill out in case of mixed sizes (CM/LM/NM).
Port plug Note 1)
A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B
With ø4 (ø5/32")
Side port
One-touch fitting
C4
(N3)
With ø6 (ø1/4")
Side port
One-touch fitting
C6
(N7)
With ø8 (ø5/16")
Side port
One-touch fitting
C8
(N9)
Special wiring Note 2)
specifications
Single wiring
Double wiring
Notes
Description/Model
Stations
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Note 1) When using port plugs, circle ports to specify.
Note 2) In case of single wiring or mixed wiring, connections to the connector terminals start from the A-side solenoid of station 1 and continue in order
without skipping any terminals.
For SMC use only
Applicable valves and options
Part no.
Qty.
Part no.
Qty.
Order no.
Clerk (code no.)
Dept. code
26
Manifold Specification Sheet
Series VQC4000: Base-Mounted Type/Plug-in Unit
q How to order manifolds
VV5QC 4 1
VV5QC 4 1
08
02
TD0
1
2
3
16
⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅
T Kit
⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅
S Kit
7
02 SDQW
4
Series VQC4000
5
6
Base-Mounted plug-in
q Stations
e Electrical entry
1 station
Kit
Stations Note 1)
Nil
w Cylinder port size
With ø8 One-touch fitting
With ø10 One-touch fitting
With ø12 One-touch fitting
Rc 1/4
Rc 3/8
Bottom ported Rc 1/4
Mixed
Note 1) Indicate the size in the
specification order sheet
in the case of CM.
Note 2) Symbols for inch sizes are
as follows:
<For One-touch fittings>
N7: ø1/4"
N9: ø5/16"
N11: ø3/8"
NM: Mixed
<For threads> P, R, A, B port
VV5QC41-0803
TD0
T Kit
⋅⋅⋅
⋅⋅⋅
K
The maximum number of stations
differs depending on the electrical
entry. Refer to e.
C8
C10
C12
02
03
B
CM
u Options
D-side
entry
TD0
S Kit
01
SD0W
SDQW
SDNW
Terminal block box kit
1 to 10 (20)
Serial kit without SI unit
Serial kit DeviceNet compatible
Serial kit PROFIBUS-DP compatible
1 to 16 (24)
Note 1) Numbers inside ( ) indicate the maximum number of solenoids for mixed single and
double wiring. The maximum number of stations is determined by the total number of
solenoids. In the case of mixed wiring, use the option symbol "-K."
N
None
Special wiring specifications Note 1)
(except for double wiring)
With name plate Note 2)
(available for T Kit only)
∗ When specifying two or more options, list
symbols in alphabetical order. Example: -KN
Note 1) Be sure to indicate the wiring specifications in the specification order sheet.
Note 2) The mounting position of the name plate is
on the top face of the cover for the terminal block box.
r SI unit COM
DeviceNet (SDQW)
—
SI unit COM.
Nil
+COM
–COM
N
U-side
PROFIBUS-DP (SDNW)
—
n
⋅
⋅
8
⋅
⋅
7
⋅
⋅
6
⋅
⋅
5
⋅
⋅
4
⋅
⋅
3
⋅
⋅
2
⋅
⋅
1
⋅
⋅
Note) Leave the box blank for the SI unit COM without input block (SD0).
t Input block
Nil
0
1
2
3
4
Without SI unit/input block (SD0)
Without input block
With 1 input block
With 2 input blocks
With 3 input blocks
With 4 input blocks
y Input block COM
Cylinder port
Thread type
Nil
PNP (+)
or without SI unit/input block (SD0)
N
NPN (–)
Nil Rc
F G
T NPT/NPTF
Stations
Note) P and R ports use
the same type of
threads.
D-side
w How to order applicable valves
VQC 4 1 0 0 Y 5 E B
Series VQC4000
A
B
C
D
E
F
∗ Stations are numbered in ascending order from the D-side.
A Type of actuation
1
2
3
4
5
6
2-position single
2-position double
3-position closed center
3-position exhaust center
3-position pressure center
3-position perfect
B Seal type
0
1
Metal seal
Rubber seal
C Function
Nil
R
Y
Standard type (1W)
External pilot
Low wattage type (0.5W)
∗ When specifying two or more
options, list symbols in alphabetical
order.
27
D Coil voltage
5
24VDC
E Light/Surge voltage
suppressor
Nil
E
With
Without
F Manual override
Nil
B
Non-locking push type (tool required)
Slotted locking type (tool required)
For ordering: Please copy this page and use it as often as necessary.
Manifold Specification Sheet
Series VQC4000/Plug-in Unit
Date:
Manifold Model
/
/
Customer name
Fill out for S Kit only
Contact person
VV5QC 4 1
Specification sheet no.
Purchase order no.
Kit type
Equipment name
Base-Mounted plug-in
set(s) Required date
Quantity
Series VQC4000
Specifications
← D-side
Stations
Description/Model
∗ Indicate required stations with a "".
U-side
→
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
A B
Single
EA PEB
A B
Valves
Double
EA P EB
A B
Closed center
EA P EB
A B
Exhaust center
EA P EB
A B
Pressure center
EA P EB
A B
Perfect
EA P EB
Options
Blanking plate
VVQ4000-10A-1
Individual SUP spacer
VVQ4000-P-1-02/03
Individual EXH spacer
VVQ4000-P-1-02/03
Throttle valve spacer
VVQ4000-20A-1
Perfect spacer with residual pressure release valve
VVQ4000-25A-1
Interface regulator (A regulator)
ARBQ4000-00-A-1
Interface regulator (B regulator)
ARBQ4000-00-B-1
Interface regulator (P regulator)
ARBQ4000-00-P-1
Cylinder port sizes
Fill out in case of mixed sizes (CM/LM/NM).
SUP/EXH block plate
VVQ4000-16A
02
Rc 1/4
03
Rc 3/8
C8
(N7)
C10
(N9)
C10
(N11)
With ø8 (ø1/4")
One-touch fitting
With ø10 (ø5/16")
One-touch fitting
With ø12 (ø3/8")
One-touch fitting
Bottom ported Rc 1/4
Special wiring Note 1)
specifications
Single wiring
Double wiring
Description/Model
Note
P
R1
R2
Stations
Note 1) In case of single wiring or mixed wiring, connections to the connector terminals start from the A-side solenoid of station 1 and continue in order without
skipping any terminals.
For SMC use only
Applicable valves and options
Part no.
Qty.
Part no.
Qty.
Order no.
Clerk (code no.)
Dept. code
28
Series VQC
Safety Instructions
These safety instructions are intended to prevent a hazardous situation and/or
equipment damage. These instructions indicate the level of potential hazard by a
label of "Caution", "Warning" or "Danger". To ensure safety, be sure to observe
ISO 4414 Note 1), JIS B 8370 Note 2) and other safety practices.
Caution: Operator error could result in injury or equipment damage.
Warning: Operator error could result in serious injury or loss of life.
Danger:
In extreme conditions, there is a possible result of serious injury or loss of life.
Note 1) ISO 4414: Pneumatic fluid power –– Recommendations for the application of equipment to transmission and
control systems.
Note 2) JIS B 8370: General rules for pneumatic equipment
Warning
1. The compatibility of pneumatic equipment is the responsibility of the person
who designs the pneumatic system or decides its specifications.
Since the products specified here are used in various operating conditions, their compatibility with the
specific pneumatic system must be based on specifications or after analysis and/or tests to meet your
specific requirements.
2. Only trained personnel should operate pneumatically operated machinery and
equipment.
Compressed air can be dangerous if an operator is unfamiliar with it. Assembly, handling or repair of
pneumatic systems should be performed by trained and experienced operators.
3. Do not service machinery/equipment or attempt to remove components until
safety is confirmed.
1. Inspection and maintenance of machinery/equipment should only be performed after confirmation of
safe locked-out control positions.
2. When equipment is to be removed, confirm the safety process as mentioned above. Cut the supply
pressure for this equipment and exhaust all residual compressed air in the system.
3. Before machinery/equipment is restarted, take measures to prevent shooting-out of cylinder piston rod,
etc. (Bleed air into the system gradually to create back pressure.)
4. Contact SMC if the product is to be used in any of the following conditions:
1. Conditions and environments beyond the given specifications, or if product is used outdoors.
2. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical
equipment, food and beverages, recreation equipment, emergency stop circuits, press applications, or
safety equipment.
3. An application that has the possibility of having negative effects on people, property, or animals, and
therefore requires special safety analysis.
29
Series VQC
5-Port Solenoid Valve Precautions 1
Be sure to read before handling.
Design
1. Actuator drive
When an actuator, such as a cylinder, is to be driven using a
valve, take appropriate measures to prevent any potential
danger caused by actuator operation.
2. Intermediate stopping
When a 3-position closed center valve is used to stop a
cylinder's piston at an intermediate position, accurate
stopping of the piston in a predetermined position is not
possible due to the compressibility of air.
Furthermore, since valves and cylinders are not guaranteed
for zero air leakage, it may not be possible to hold a stopped
position for an extended length of time. Contact SMC if it is
necessary to hold a stopped position for an extended time.
3. Effect of back pressure when using a
manifold
Use caution when valves are used on a manifold, as actuator
malfunction due to back pressure may occur. Special caution
is necessary when using a 3-position exhaust center valve, or
when driving a single acting cylinder. In cases where there is
a danger of this kind of malfunction, take countermeasures by
using a back-pressure check valve, an individual EXH spacer
assembly, or an EXH blocking plate.
4. Dealing with pilot exhaust
Operate the pilot exhaust port (PE) with silencers mounted on
both the D and U sides, or with release to atmosphere. If
merged with the main exhaust, the main valve may
malfunction due to back pressure.
Warning
1. Confirm all specifications.
The products featured in this catalog are designed only for use
in compressed air systems (including vacuum). Do not operate
at pressures or temperatures beyond the range of specifications,
as this can cause damage or malfunction. (Refer to specifications.)
Contact SMC when using a fluid other than compressed air
(including vacuum).
2. Extended periods of continuous energization
Contact SMC if valves will be continuously energized for
extended periods of time.
Caution
1. Momentary energization
If a double solenoid valve will be operated with momentary
energization, it should be energized for at least 0.1 second.
However, depending on the secondary load conditions, it
should be energized until the cylinder reaches the stroke end
position. If the valve is to be used in an air blowing application,
it should be energized continuously during the application.
2. Leakage voltage
When using a C-R element (surge voltage suppressor) for
protection of the switching element, please keep in mind that
leakage voltage will increase due to leakage current flowing
through the C-R element.
Switching element
5. Holding of pressure (including vacuum)
Since valves are subject to air leakage, they cannot be used
for applications such as holding pressure (including vacuum)
in a pressure vessel.
OFF
Power
supply
7. Maintenance space
The installation should allow sufficient space for maintenance
activities.
8. Release of residual pressure
Provide a residual pressure release function for maintenance
purposes. Special consideration should be given to the
release of residual pressure between the valve and cylinder
in the case of a 3-position closed center type valve.
9. Vacuum applications
When a valve is used for vacuum switching, take appropriate
measures against the suction of external dust or other
contaminants through vacuum pads and exhaust ports. An
external pilot type valve should be used in such cases.
Contact SMC regarding the use of an internal pilot type or air
operated valve.
10. Take suitable protective measures in
locations or applications where valves are
constantly exposed to water.
R
Leakage current
6. Not for use as an emergency shutoff valve
None of the valves featured in this catalog is designed for
safety applications such as an emergency shutoff valve. If
application to this type of system is required, other reliable
safety assurance measures should also be adopted.
C
Leakage
voltage
Warning
Selection
Valve
Limit the amount of residual leakage voltage to the following
values:
With DC coil
2% or less of rated voltage
3. Low temperature operation
Avoid ambient temperatures outside the range of –10°C to
50°C. At low temperatures, take any necessary steps to avoid
solidification or freezing of drainage and moisture.
4. For air blowing applications
When using solenoid valves for air blowing, use external pilot
type valves.
Also, air supply to the external pilot port should be compressed
air that is within the pressure range prescribed in the
specifications.
5. Mounting orientation
In the case of a single solenoid, the mounting orientation is
unrestricted. In the case of double solenoid or 3-position
valves, mount so that the spool valve is horizontal.
Also, when mounting for an application that will inevitably
involve vibration or impact, mount so that the spool valve is at
a right angle to the direction of vibration.
Do not use in applications where vibration or impact exceed
the product's specifications.
30
Series VQC
5-Port Solenoid Valve Precautions 2
Be sure to read before handling.
Mounting
Wiring
Warning
Caution
1. If air leakage increases or equipment does
not operate properly, stop operation.
After mounting, repairs, or equipment modification, connect the
compressed air and power supplies, and perform appropriate
function and leakage inspections to confirm that the unit is
mounted properly.
2. Instruction manual
Mount and operate the product only after reading the manual
carefully and understanding its contents. Always keep the
manual handy for easy reference.
3. Painting and coating
Warnings or specifications printed or pasted on the product
should not be erased, removed or covered up.
1. Polarity
Always confirm whether or not there is polarity when
connecting a power supply to a DC specification solenoid valve
equipped with a (light) voltage surge suppressor.
If there is a polarity, observe the following precautions:
• If there is no built-in diode for polarity protection:
Switching polarity by mistake poses the danger of burnout to
the valve's built-in diode and the switching element on the
control mechanism side, as well as to the power supply
mechanism.
• If there is a diode for polarity protection:
Switching polarity by mistake will cause the valve's switching
function to stop.
∗ Series VQ4000 has no polarity. (It is a polarity-free type valve.)
2. Applied voltage
Piping
Be careful to apply the proper voltage when connecting electric
power to the solenoid valve. Application of improper voltage
may cause malfunction or coil damage.
Caution
1. Preparation before piping
Before piping is connected, it should be thoroughly flushed out
with air or washed out with water to remove chips, cutting oil
and other debris.
3. Confirm the connections.
After completing the wiring, confirm that all the connections are
correct.
2. Wrapping of sealant tape
When connecting pipes and fittings, etc., be sure that neither
chips from the pipe threads nor sealing material get inside the
valve.
When using sealant tape, leave 1.5 to 2 thread ridges exposed
at the end of the pipe/fitting.
Winding
direction
Ex
po
se
Sealant tape
ap
pr
ox
.2
thr
ea
ds
3. When using closed center type valves
When using closed center type valves, check carefully to make
sure there are no air leaks from the piping between the valves
and cylinders.
4. Ensure tightening to the prescribed tightening torques.
When screwing fittings into valves, tighten according to the
torques given below.
Tightening torques for piping
Connection thread
Proper tightening torque (N⋅m)
Rc 1/8
Rc 1/4
Rc 3/8
Rc 1/2
Rc 3/4
7 to 9
12 to 14
22 to 24
28 to 30
28 to 30
5. Connection of piping to products
When connecting piping to a particular product, refer to the
product's instruction manual to avoid mistakes regarding the
supply port and other connections as applicable.
31
Lubrication
Caution
1. Lubrication
1) The valve has been lubricated for life at the factory, and does
not require any further lubrication.
2) Should you wish to apply additional lubrication, however,
please be sure to use ISO VG32 Class 1 turbine oil (without
additives).
Please be aware, however, that once additional lubrication is
applied, it must be continued to avoid malfunctions, as the
new lubricant will completely cancel out the original
lubrication.
Series VQC
5-Port Solenoid Valve Precautions 3
Be sure to read before handling.
Maintenance
Air Supply
Warning
1. Use clean air.
Do not use compressed air which contains chemicals, synthetic
oils containing organic solvents, salts or corrosive gases, etc.,
as this can cause damage or malfunction.
Caution
1. Install air filters.
Install air filters close to valves at their upstream side. A
filtration degree of 5µm or less should be selected.
2. Install an air dryer or after-cooler.
Compressed air that includes excessive drainage may cause
malfunction of valves and other pneumatic equipment. To
prevent this, install an air dryer or after-cooler.
3. If excessive carbon powder is generated,
eliminate it by installing mist separators at
the upstream side of valves.
If excessive carbon powder is generated by the compressor, it
may adhere to the inside of valves and cause malfunction.
Refer to SMC's "Air Cleaning Equipment" catalog for further
details on compressed air quality.
Operating Environment
Warning
1. Do not use valves where there is direct
contact with, or in atmospheres of, corrosive
gases, chemicals, salt water, water or steam.
2. Do not use in an explosive atmosphere.
3. Do not use in locations subject to vibration or
impact. Confirm the specifications for each
series.
4. A protective cover should be used to shield
valves from direct sunlight.
5. Shield valves from radiated heat generated
by nearby heat sources.
6. Employ suitable protective measures in
locations where there is contact with water
droplets, oil, or welding spatter.
7. When solenoid valves are mounted in a
control panel or are energized for extended
periods of time, employ measures to radiate
excess heat so that temperatures remain
within the valve specification range.
Warning
1. Perform maintenance procedures as shown
in the instruction manual.
If handled improperly, malfunction or damage of machinery or
equipment may occur.
2. Equipment removal and supply/exhaust of
compressed air
When equipment is to be removed, first confirm that measures
are in place to prevent dropping of driven objects and run-away
of equipment, etc. Then cut the supply air pressure and electric
power, and exhaust all compressed air from the system using
its residual pressure release function.
When the equipment is to be started again after remounting or
replacement, first confirm that measures are in place to prevent
lurching of actuators and then confirm that equipment operates
normally.
3. Infrequent operation
Valves should be switched at least once every 30 days to
prevent malfunction. (Use caution regarding the air supply.)
4. Manual override operation
When the manual override is operated, connected equipment
will be actuated. Confirm safety before operating.
Caution
1. Filter drainage
Drain out condensate from air filters regularly. (Refer to specifications.)
2. Lubrication
In the case of rubber seals, once lubrication has been started,
it must be continued.
Use VG32 Class 1 turbine oil (without additives). Other
lubricating oils will cause malfunctions.
Contact SMC regarding VG32 Class 2 turbine oil (with
additives).
How to Find the Flow Rate (at air temperature of 20°C)
Subsonic flow when P1 + 0.1013 < 1.89 (P2 + 0.1013)
Q = 226S
P(P2 + 0.1013)
Sonic flow when P1 + 0.1013 ≥ 1.89 (P2 + 0.1013)
Q = 113S (P1 + 0.1013)
Q: Air flow rate [l/min (ANR)]
S: Effective area [mm²]
P: Pressure drop rate (P1–P2) [MPa]
P1: Upstream pressure [MPa]
P2: Downstream pressure [MPa]
∗ Correction for different air temperatures
Multiply the flow rate calculated with the above formulas by a
coefficient from the table below.
Air temperature (°C)
–20
Correction coefficient 1.08
–10
1.06
0
10
30
40
50
1.04 1.02 0.98 0.97 0.95
60
0.94
32
Series VQC
Specific Product Precautions 1
Be sure to read before handling.
Refer to pages 29 through 32 for safety instructions and common precautions.
Caution
Warning
Manual Override
Solenoid Valve Removal and Mounting
VQC1000/2000
Since connected equipment will operate when the
manual override is activated, confirm that conditions
are safe prior to activation.
The non-locking push type (tool required) is
standard, and the slotted locking type (tool required)
is optional.
VQC1000/2000
Non-locking push type (tool required)
Bore ø4.2
Bore ø3.2
VQC1000
VQC2000
Push down the manual
override button with a small
screwdriver, etc., until it
stops.
The manual override will
return when released.
Slotted locking type (tool required) <Optional>
Bore ø3.2
VQC1000
Bore ø4.2
Push down the manual
override button with a small
flat head screwdriver until it
stops, and turn it clockwise
90° to lock it. Turn it counterclockwise to release it.
VQC2000
Locking type (manual) <Optional>
11mm
VQC1000
1. Loosen the clamp screws until they turn freely. (The screws do
not come out.)
2. Remove the solenoid valve from clamp B by lifting the coil side
of the valve while pushing on the screw top.
If pushing down on the screw is difficult, you can alternately
press down on the valve gently in the area near the manual
override.
Mounting steps
1. Push the clamp screws. Clamp A opens. Now insert the end
plate hook of the valve into clamp B from an angle.
2. Push the valve down into place. (When you release the screws,
the valve will be locked into clamp A.)
3. Tighten the clamp screws with a tightening torque of 0.25 to
0.35N⋅m for VQC1000 and 0.5 to 0.7N⋅m for VQC2000.
Caution
Push down the manual
override button with a small
flat head screwdriver or with
your finger until it stops, and
turn it clockwise 90° to lock
it. Turn it counterclockwise
to release it.
10mm
Removal steps
VQC2000
Do not let foreign matter stick on the seal side of the gasket and
solenoid, as this will cause air leakage.
Caution
Valve Mounting
VQC4000
After confirming that the gasket is installed
correctly, securely tighten the mounting screws
according to the tightening torque shown
below.
VQC4000
Non-locking push type (tool required)
Bore ø5
Push down the manual
override button with a small
screwdriver until it stops.
The manual override will
return when released.
Locking type (manual) <Optional>
Bore ø5
Push down the manual
override button with a small
flat head screwdriver until it
stops, and turn it clockwise
90° to lock it. Turn it counterclockwise to release it.
PUSH
TURN
LOCK
33
Proper tightening torque (N⋅m)
0.8 to 1.2
Mounting screw (M3)
Series VQC
Specific Product Precautions 2
Be sure to read before handling.
Refer to pages 29 through 32 for safety instructions and common precautions.
Caution
Caution
Replacing One-touch fittings
Light/Surge voltage suppressor VQC1000/2000
Cylinder port fittings are available in cassette
type and can be replaced easily.
Fittings are secured with a retaining clip that is
inserted from the top side of the valve. After
removing the valve, remove the clip with a flat
head screw driver to replace the fittings.
To mount a fitting, insert the fitting assembly
until it stops and reinsert the retaining clip to its
designated position.
Indicator lights are all positioned on one side
for both single solenoid and double solenoid
type valves.
For double solenoid type, 2 colors that are
same as the manual override are used to
indicate the energization of A-side or B-side.
Manual override: Green
VQC1000/2000
Indicator light: Orange
Single solenoid type
Double solenoid type
Manual override: Orange
Indicator light
A: Orange
B: Green
(For VQC1000)
DC circuit
Single solenoid type
Applicable tube O.D.
ø3.2
ø4
ø6
ø8
M5
ø1/8"
ø5/32"
ø1/4"
ø5/16"
Double solenoid type
Fitting assembly part no.
VQC1000
VQC2000
VVQ1000-50A-C3
VVQ1000-50A-C4
VVQ1000-50A-C6
—
VVQ1000-50A-M5
VVQ1000-50A-N1
VVQ1000-50A-N3
VVQ1000-50A-N7
—
—
VVQ1000-51A-C4
VVQ1000-51A-C6
VVQ1000-51A-C8
—
—
VVQ1000-51A-N3
VVQ1000-51A-N7
VVQ1000-51A-N9
With miswiring prevention mechanism
With surge absorbing mechanism (surge absorbing diode) mechanism
Note) A-side energized: Light (orange) ON
B-side energized: Light (green) ON
Caution
VQC4000
Internal Wiring Specifications
VQC4000
Clip
SOL
ZNR
Fitting assembly
Light circuit assembly
(orange)
– (+)
+ (–)
DC: Single
A-side – (+) B-side – (+)
SOL
Applicable tube O.D.
ø8
ø10
ø12
ø1/4"
ø5/16"
ø3/8"
VQC4000
VVQ4000-50B-C8
VVQ4000-50B-C10
VVQ4000-50B-C12
VVQ4000-50B-N7
VVQ4000-50B-N9
VVQ4000-50B-N11
SOL
ZNR
Fitting assembly part no.
A-side light circuit assembly
(orange)
ZNR
COM+ (–)
DC: Double
B-side light circuit assembly
(green)
34
Series VQC
Specific Product Precautions 3
Be sure to read before handling.
Refer to pages 29 through 32 for safety instructions and common precautions.
Serial wiring EX500/EX250/EX240 Precautions
Warning
1. These products are intended for use in
general factory automation equipment.
Avoid using these products in machinery/equipment which
affects human safety, and in cases where malfunction or failure
can result in extensive damage.
2. Do not use in explosive environments, in the
presence of inflammable gases, or in corrosive environments. This can cause injury or
fire.
3. Work such as transporting, installing, piping,
wiring, operation, control and maintenance
should be performed by knowledgable and
qualified personnel only. As handling involves the risk of a danger of electrocution,
injury or fire.
4. Install an external emergency stop circuit
that can promptly stop operation and shut off
the power supply.
5. Do not modify these products. Modifications
done to these products carry the risk of
injury and damage.
Caution
1. Read the instruction manual carefully, strictly
observe the precautions and operate within
the range of the specifications.
2. Do not drop these products or submit them to
strong impacts. This can cause damage, failure or malfunction.
3. In locations with poor electrical conditions,
take steps to ensure a steady flow of the rated power supply. Use of a voltage outside of
the specifications can cause malfunction,
damage to the unit, electrocution or fire.
4. Do not touch connector terminals or internal
circuit elements when current is being supplied. There is a danger of malfunction, damage
to the unit or electrocution if connector terminals or internal circuit elements are touched
when current is being supplied.
Be sure that the power supply is OFF when adding or removing
manifold valves or input blocks or when connecting or disconnecting connectors.
5. Operate at an ambient temperature that is
within the specifications. Even when the ambient temperature range is within the specifications, do not use in locations where there
are rapid temperature changes.
35
Caution
6. Keep wire scraps and other extraneous materials from getting inside these products.
This can cause fire, failure or malfunction.
7. Give consideration to the operating environment depending on the type of enclosure
being used.
To achieve IP65 and IP67 protection, provide appropriate wiring between all units using electrical wiring cables, communication connectors and cables with M12 connectors. Also, provide waterproof caps when there are unused ports, and perform proper mounting of input units, input blocks, SI units and
manifold valves. Provide a cover or other protection for applications in which there is constant exposure to water.
8. Use the proper tightening torques.
There is a possibility of damaging threads if tightening exceeds the tightening torque range.
9. Provide adequate protection when operating
in locations such as the following:
• Where noise is generated by static electricity
• Where there is a strong electric field
• Where there is a danger of exposure to radiation
• When in close proximity to power supply lines
10. When these products are installed in equipment, provide adequate protection against
noise by using noise filters.
11. Since these products are components
whose end usage is obtained after installation in other equipment, the customer
should confirm conformity to EMC directives for the finished product.
12. Do not remove the name plate.
13. Perform periodic inspections and confirm
normal operation, otherwise it may be impossible to guarantee safety due to unexpected malfunction or erroneous operation.
Series VQC
Specific Product Precautions 4
Be sure to read before handling.
Refer to pages 29 through 32 for safety instructions and common precautions.
Power Supply Safety Instructions
Cable Safety Instructions
Caution
Caution
1. Operation is possible with a single power
supply or a separate power supply. However,
be sure to provide two wiring systems (one
for solenoid valves, and one for input and
control units).
2. Use the following UL approved products for
DC power supply combinations.
(1) Controlled voltage current circuit conforming to UL508
Circuit uses the secondary coil of an isolated transformer as
the power supply, satisfying the following conditions.
• Max. voltage (with no load): 30Vrms (42.4V peak) or less
• Max. current: q 8A or less (including shorts), and
w When controlled by a circuit protector
(fuse) with the following ratings:
No-load voltage (V peak)
0 to 20 [V]
Over 20 [V] and up to 30 [V]
1. Avoid miswiring, as this can cause malfunction, damage and fire in the unit.
2. To prevent noise and surge in signal lines,
keep all wiring separate from power lines and
high voltage lines. Otherwise, this can cause
a malfunction.
3. Check wiring insulation, as defective insulation can cause damage to the unit when
excessive voltage or current is applied.
4. Do not bend or pull cables repeatedly, and do
not place heavy objects on them or allow
them to be pinched. This can cause broken
lines.
Max. current rating
5.0
100
Peak voltage value
(2) A circuit (class 2 circuit) with maximum 30Vrms (42.4V peak)
or less, and a power supply consisting of a class 2 power
supply unit conforming to UL1310, or a class 2 transformer
conforming to UL1585
36
37
SMC'S GLOBAL MANUFACTURING, DISTRIBUTION AND SERVICE NETWORK
EUROPE
EUROPE
NORTH AMERICA
AUSTRIA
SMC Pneumatik GmbH
CZECH
SMC Industrial Automation CZ s.r.o.
DENMARK
SMC Pneumatik A/S
FINLAND
SMC Pneumatiikka OY
FRANCE
SMC Pneumatique SA
GERMANY
SMC Pneumatik GmbH
HUNGARY
SMC Hungary Ipari Automatizálási Kft.
IRELAND
SMC Pneumatics (Ireland) Ltd.
ITALY
SMC Italia S.p.A.
NETHERLANDS
SMC Pnuematics BV.
NORWAY
SMC Pneumatics Norway A/S
POLAND
SMC Industrial Automation Polska Sp.z.o.o.
ROMANIA
SMC Romania s.r.l.
RUSSIA
SMC Pneumatik LLC.
SLOVAKIA
SMC Priemyselná automatizáciá, s.r.o.
SLOVENIA
SMC Industrijska Avtomatika d.o.o.
SPAIN/PORTUGAL
SMC España, S.A.
SWEDEN
SMC Pneumatics Sweden AB
SWITZERLAND
SMC Pneumatik AG.
UK
SMC Pneumatics (U.K.) Ltd.
CANADA
SMC Pneumatics (Canada) Ltd.
MEXICO
SMC Corporation (Mexico) S.A. de C.V.
USA
SMC Corporation of America
SOUTH AMERICA
ASIA
CHINA
SMC (China) Co., Ltd.
HONG KONG
SMC Pneumatics (Hong Kong) Ltd.
INDIA
SMC Pneumatics (India) Pvt. Ltd.
MALAYSIA
SMC Malaysia (S.E.A.) Sdn. Bhd.
PHILIPPINES
SMC Pneumatics (Philippines), Inc.
SINGAPORE
SMC Pneumatics (S.E.A.) Pte. Ltd.
SOUTH KOREA
SMC Pneumatics Korea Co., Ltd.
TAIWAN
SMC Pneumatics (Taiwan) Co., Ltd.
THAILAND
SMC Thailand Ltd.
ARGENTINA
SMC Argentina S.A.
BOLIVIA
SMC Pneumatics Bolivia S.R.L.
BRAZIL
SMC Pneumaticos Do Brazil Ltda.
CHILE
SMC Pneumatics (Chile) S.A.
VENEZUELA
SMC Neumatica Venezuela S.A.
OCEANIA
AUSTRALIA
SMC Pneumatics (Australia) Pty. Ltd.
NEW ZEALAND
SMC Pneumatics (N.Z.) Ltd.
1-16-4 Shimbashi, Minato-ku, Tokyo 105-0004, JAPAN
Tel: 03-3502-2740 Fax: 03-3508-2480
URL http://www.smcworld.com
© 2001 SMC CORPORATION All Rights Reserved
1st printing June, 2001
D-SMC.L.A. P-80 (D)
This catalog is printed on recycled paper with concern for the global environment.
All specifications in this catalog are subject to change without notice.
Printed in Japan.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement