Century 9055 [0500620] [04/1998]

Century 9055 [0500620] [04/1998]
CENTURY
L E G E N D A R Y
®
L E A D E R S H I P
OWNER'S MANUAL
9055
INSTALLATION, OPERATION, MAINTENANCE & PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without notice
All ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Phone (423) 238-4171 • FAX (423) 238-5371
FORM NO. 0500620
4 / 98
PRICE $25.00
LIMITED WARRANTY
MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the
original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in
material and workmanship for a period of twelve (12) months from date placed in service, but in no event
shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The
purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event
shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve
(12) months from date placed in service, whichever is earlier.
MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at
the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon
inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be
used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not
obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or
replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or
alterations have been made unless authorized by MILLER.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER
WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime,
claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages
concerning or relating to any product or parts, whether based on negligence, strict liability, breach of
contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss
resulted from any general or particular requirement which MILLER knew or had reason to know about at
the time of sale.
MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS
MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO
PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any
accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR
PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such
warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted
under applicable law, pass on to the purchaser such manufacturer's or seller's warranty.
MILLER, whose policy is one of continuous improvement, reserves the right to improve its products
through changes in design or materials as it may deem desirable without being obligated to incorporate
such changes in products previously sold. This warranty is not intended to cover or include the following
items, which are set forth by way of example and not limitation:
A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to
weather, road conditions, road treatments, etc.
B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure
to provide reasonable and necessary maintenance, or uses for which the equipment was not
designed or intended.
C. Alterations or modifications that affect performance, operation or reliability.
D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud
flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.
IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER
PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY
OTHER IMPROPER USE.
SERIAL NUMBER
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Telephone (423) 238-4171
Section VI - PARTS
This Section is provided by the manufacturer for the purpose of ordering
any component part of the CENTURY 9055 Wrecker that may be required
when part replacement is necessary. Be certain to use only original equipment
replacement parts for warranty purposes as well as for keeping your
CENTURY 9055 Wrecker in its original state and optimum operating
capacities.
When ordering replacement or spare parts be sure to provide the following
information to the manufacturer’s Parts Department.
1.
2.
3.
4.
5.
6.
7.
Manual Number & Date of Publication
Manual Page Number
Page Title
Reference Number of Part Desired
Part Number
Part Description
Quantity of Part Desired
Providing this information will help ensure that the correct parts will be
delivered to you in an expedient manner without delay. Should additional
information be required for repair or replacement of certain components,
contact your Wrecker Manufacturer Authorized Representative.
The Manufacturer reserves the right, without notice or obligation, to improve
or modify their products, which may change the specifications, models and
feature availability.
VI-1
Section VI - PARTS (cont'd)
SUBFRAME ASSEMBLY
VI-2
Section VI - PARTS (cont'd)
SUBFRAME ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
REF.
8
20
REF.
2
8
10
4
2
2
1
4
4
12
4
17
5
4
12
8
8
4
2
2
2
2
2
1
2
1
1
2
1
2
-2
2
2
2
0300680
0302540
0302541
0302792
0303089
0400066
0400128
0400139
0400206
0400211
0400220
0400276
0400281
0400288
0400294
0400392
0400408
0400430
0400431
0400452
0400506
0400508
0700884
0707117
0707194
0707199
0708094
0802211
0802221
0802398
0802399
0802463
0803571
0803613
0903729
0303445
0400211
0400408
0400492
DESCRIPTION
CYLINDER, REAR SPADE
CENTER BONDED MOUNT (BE0102)
WASHER, SPECIAL (BE0103)
CYLINDER, BOOM ELEVATION
RAMP PAD
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" FL HD SKT
SCREW, 3/8"-16 X 1-1/2" HEX SKT SET
SCREW, 1/2"-13 X 5" HEX HD CAP
SCREW, 1/2"-13 X 1-3/4" HEX HD CAP
SCREW, 1/2"-13 X 5-1/2" HEX HD CAP
SCREW, 5/8"-11 X 4-1/2" HEX HD CAP
SCREW, 3/4"-10 X 3-1/2" HEX HD CAP
SCREW, 3/4"-10 X 2-1/2" HEX HD CAP GR8
SCREW, 3/4"-10 X 6-1/2" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
NUT, 1/2"-13 NYLOK HEX
NUT, 3/4"-10 NYLOK HEX
NUT, 3/4"-10 NYLOK HEX GR8
LOCKWASHER, 1/4" HELICAL
WASHER, 5/8" FLAT
LOCKWASHER, 5/8" HELICAL
SHAFT, LOWER JACK
SHAFT, UPPER SPADE
COVER, SPADE TUBE
PIN, SPADE PAD
PIN, LIFT CYLINDER
FRONT BODY MTG TUBE
SPADE PAD
SPADE, LEFT INNER
SPADE, RIGHT INNER
PIVOT PIN WELDMENT, LIFT CYLINDER
SUBFRAME WELDMENT
BOOM PIVOT BRACKET
SAFETY CHAIN ASSEMBLY (NOT SHOWN)
SAFETY CHAIN, SYSTEM 10, 1/2" X 14'
SCREW, 1/2"-13 X 1-3/4" HEX HD CAP
NUT, 1/2"-13 NYLOK HEX
WASHER, 1/2" FLAT
VI-3
Section VI - PARTS (cont'd)
BODY ASSEMBLY
VI-4
Section VI - PARTS (cont'd)
BODY ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
111
19
20
21
22
23
24
25
26
27
28
29
30
31
32
28 FT
2
6
1
1
1
1
6
8
38
6
8
38
6
76
1
1
2
4
2
2
2
2
1
1
1
1
1
1
2
1
1
0300345
0301223
0301912
0302562
0302978
0302979
0303061
0400066
0400122
0400288
0400369
0400392
0400431
0400451
0400566
0705090
0705091
0705092
0706609
0707174
0707175
0709453
0711286
0711289
0711290
0711291
0711292
0802224
0802225
0802226
0802260
0901496
DESCRIPTION
RUBBER FENDER
MUDFLAP
DOOR CHECK, 11"
LIGHT BAR, DELUXE (OPTIONAL)
LEFT TOOL COMPARTMENT, 156" C.B.
RIGHT TOOL COMPARTMENT, 156" C.B.
BACK UP ALARM (NOT SHOWN)
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1 /4" HEX HD CAP
SCREW, 3/4"-10 X 2-1/2" HEX HD CAP GR8
CLIP, 1/4" TINNERMAN
NUT, 3/8"-16 NYLOK HEX
NUT, 3/4"-10 NYLOK HEX GR8
WASHER, 1/4" FLAT
RIVET, 1/4"
MUDFLAP MTG ANGLE, LEFT
MUDFLAP MTG ANGLE, RIGHT
BAR, MUDFLAP
RETAINING STRIP, FENDER
TAILGATE MOUNTING ANGLE
MOUNTING PLATE
MOUNTING PLATE
SPACER, REAR FRAME BRACKET
SWITCH PANEL, RIGHT
CONTROL PANEL, RIGHT
GAUGE PANEL
CONTROL PANEL
VERTICAL SUPPORT, L.H.
VERTICAL SUPPORT, R.H.
MOUNTING BRACKET
TOP CHANNEL
CENTURY NAMEPLATE KIT
VI-5
Section VI - PARTS (cont'd)
BOOM ASSEMBLY
VI-6
Section VI - PARTS (cont'd)
BOOM ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
18
39
5
2
2
4
2
REF.
4
4
8
6
2
4
8
4
4
8
4
4
4
6
2
2
2
2
1
2
2
1
1
1
2
1
1
2
4
1
2
2
1
0300113
0300311
0301923
0302378
0302538
0302830
0302831
0400121
0400132
0400133
0400140
0400248
0400392
0400408
0400482
0400492
0400506
0400508
0400543
0400557
0700511
0700563
0700776
0700778
0707176
0707190
0707235
0708124
0708127
0708128
0709706
0800222
0800223
0802027
0802218
0802397
0802438
0102499
0802860
DESCRIPTION
GREASE FITTING
SHEAVE, 10"
SLIDE PAD, BOOM BOTTOM
COMPRESSION SPRING
BUSHING, 3-1/2" O.D. X 3" I.D. X 2-1/2"
CYLINDER, EXTEND
SNAP RING, INTERNAL
SCREW, 3/8"-1 6 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/2" HEX HD CAP
SCREW, 3/8"-16 X 3" HEX HD CAP
SCREW, 3/8"-16 X 4" HEX HD CAP
SCREW, 5/8"-11 X 1" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
NUT, 1/2"-13 NYLOK HEX
LOCKWASHER, 3/8" HELICAL
WASHER, 1/2" FLAT
WASHER, 5/8" X 1-3/4" FLAT
LOCKWASHER, 1/8" HELICAL
COTTER PIN, 1/8" X 3/4" SS
ROLL PIN, 1/2" X 1-1/4"
BOTTOM, CABLE GUIDE
SHAFT, SHEAVE
SLIDE PAD
TOP SPACER, OUTER BOOM
PIVOT PIN, BOOM
PIVOT ROD
SPRING CHANNEL
PIN, TILT CYLINDER BASE
PIN, EXTEND CYLINDER (BASE)
PIN, EXTEND CYLINDER (ROD)
PLATE, FLAPPER DP 45,000 LB. WINCH
BOOM END SWIVEL, LEFT
BOOM END SWIVEL, RIGHT
CABLE GUIDE
SPRING PIN
INNER BOOM WELDMENT
TENSIONER MOUNTING PLATE
TENSIONER BRACKET
OUTER BOOM WELDMENT
VI-7
Section VI - PARTS (cont'd)
UNDERLIFT & TOWER ASSEMBLY
VI-8
Section VI - PARTS (cont'd)
UNDERLIFT & TOWER ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
2
3
1
1
2
REF.
3
2
1
2
REF.
4
REF.
1
1
1
8
1
6
4
3
4
2
4
2
6
6
0300110
0300113
0301197
0301398
0301691
0301811
0301817
0301818
0301822
0302273
0302537
0302538
0302791
0303088
0303097
0303098
0400044
0400121
0400151
0400152
0400176
0400196
0400205
0400206
0400271
0400408
0400481
DESCRIPTION
SNAP RING, 1"
GREASE FITTING
COMPRESSION SPRING, CROSSBAR
STEEL BALL, 1-3/16" DIA.
OBLONG LINK
CYLINDER, BOOM EXTENSION
SLIDE PAD
SLIDE PAD
O-RING, PIVOT PIN
SPRING
CYLINDER, FOLD
BUSHING, 3.5" O.D. X 3" I.D. X 2.5" SPRING
CYLINDER, TILT
BUSHING, PIVOT PIN
WASHER, THRUST
WASHER, THRUST
SCREW, #10 TYPE "U" DRIVE
SCREW, 3/8"-16 X 3/4" HEX HD CAP
SCREW, 3/8"-24 X 3/4" HEX HD CAP GR5
SCREW, 3/8"-24 X 5/8" FLAT SKT HD
SCREW, 1/2"-13 X 1" HEX HD CAP
SCREW, 1/2"-13 X 1-1/4", SKT HD CAP
SCREW, 1/2"-13 X 3" HEX HD CAP GR5
SCREW, 1/2"-13 X 5" HEX HID CAP
SCREW, 5/8"-11 X 4-1/2" SKT HD CAP
NUT, LOCK 1/2"-13
LOCKWASHER, 3/8" EXT TOOTH
VI-9
REF.
NO.
NO.
REQ'D
PART
NUMBER
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
1
3
2
2
1
1
1
2
1
1
1
1
1
1
2
REF.
1
REF.
REF.
1
1
1
2
1
1
1
REF.
0400482
0400491
0400508
0703231
0703233
0703235
0703236
0703277
0707179
0708124
0708125
0708470
0710051
0710052
0710450
0800590
0800998
0802155
0802156
0802393
0802394
0802459
0802460
0802461
0802914
0802915
0900900
DESCRIPTION
LOCKWASHER, 3/8"
LOCKWASHER, 1/2" HELICAL
LOCKWASHER, 5/8"
PLATE, STOP, OUTER BOOM
PLATE, STOP
SHAFT, INNER BOOM CYLINDER
SHAFT, OUTER BOOM CYLINDER
PAD, SLIDER
PIN
PIN, TILT CYLINDER BASE
PIN, TILT CYLINDER ROD
SPACER, DETENT SPRING
PIN, PIVOT, TOP HALF
PIN, PIVOT, BOTTOM
BAR, RETRACT
TEE HANDLE
BOOM, 2ND STAGE
FORK ADAPTER, L.H. (SHOWN)
FORK ADAPTER, R.H.
BOOM, OUTER
UNDERLIFT TOWER
PIN, FOLD CYLINDER
TOWER PIVOT PIN
PIN, UNDERLIFT PIVOT
CROSSBAR
BOOM, 3RD STAGE
PIN, RETAINER
Section VI - PARTS (cont'd)
UNDERLIFT HYDRAULICS
VI-10
Section VI - PARTS (cont'd)
UNDERLIFT HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
111
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
7
1
1
1
2
6
1
2
1
1
1
1
6
6
REF.
4 PR.
24
8
6
2
REF.
REF.
2
1
2
2
1
1
2
1
6
2
REF.
1
1
1
8
0300044
0300206
0300209
0301425
0301473
0301470
0301522
0301620
0301730
0301731
0301837
0302035
0302504
0302514
0302537
0302548
0302549
0302551
0302576
0302584
0302791
0302798
0302805
0302812
0302813
0302842
0302911
0302914
0302915
0303017
0303342
0303348
0303501
0303561
0303562
0303563
0400118
DESCRIPTION
CONNECTOR, 6MJ-8MB
BRANCH TEE, 6MJ-6MJ-4MP
ELBOW, 6MJ-6MP90
CONNECTOR, 6MJ-6MP
HOSE ASSEMBLY, 18"
ELBOW, 6MJ-8MP90
CONNECTOR 6MJ-6MB
ELBOW, 6MJ-6MB90
DOUBLE HOLDING VALVE
HOLDING VALVE
INLINE ORIFICE
HOSE ASSEMBLY, 18"
TUBE ASSEMBLY
ADAPTER, 8MJ-6MJ
CYLINDER, FOLD
CLAMPING UNIT
SPLIT BUSHING
STACKING NUT, SKT HD
BULKHEAD UNION W/NUT
HOSE ASSEMBLY, 50"
CYLINDER, TILT
CONTROL VALVE, VDP11DDC10
HOSE ASSEMBLY, 10"
HOSE ASSEMBLY, 78"
HOSE ASSEMBLY, 108"
TEE, 8MJ-8MJ-8MB
HOSE ASSEMBLY, 88"
HOSE ASSEMBLY, 35"
HOSE ASSEMBLY, 12"
CONNECTOR, 8MB-6FB
HOSE ASSEMBLY, 30"
HOSE ASSEMBLY, 48"
CYLINDER, EXTEND
HOSE ASSEMBLY, 24"
HOSE ASSEMBLY, 37"
HOSE ASSEMBLY, 27"
SCREW, 5/16"-18 X 3/4" HEX HD CAP
VI-11
Section VI - PARTS (cont'd)
BOOM HYDRAULICS
VI-12
Section VI - PARTS (cont'd)
BOOM HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
2
4
2
2
4
2
4
2
2
2
REF.
2
4
2
2
2
2
2
1
2
2
1
1
1
1
4
4
4
4
2
0300041
0300113
0300644
0300657
0300659
0301376
0301388
0301731
0301778
0302051
0302296
0302568
0302569
0302574
0302576
0302792
0302796
0302797
0302830
0302930
0303343
0303346
0303347
0303354
0303355
0400064
0400366
0400451
0400452
0703001
DESCRIPTION
CONNECTOR, 8MJ-8MB
GREASE FITTING
HOSE CLAMP, 8"
HOSE ASSEMBLY, 46"
HOSE ASSEMBLY, 45"
CONNECTOR, 6MJ-8MB
ELBOW, 8MJ-8MB90
HOLDING VALVE
CONNECTOR, 6MJ-10MB
ELBOW, 8MJ-6MP90
CONTROL VALVE, VDP12CDD118
HYDRAULIC TUBING
WIRE TIE, 29-3/4" (NOT SHOWN)
BULKHEAD RUN TEE, 8MJ-8BLKHD-8MJ
BULKHEAD UNION, 8MJ-8BLKHD
LIFT CYLINDER
TEE, 8MJ-8MJ-8FJX
ELBOW, 8MJ-4MP90
EXTEND CYLINDER
CONNECTOR, 8MJ-6MP
HOSE ASSEMBLY, 45"
HOSE ASSEMBLY, 48"
HOSE ASSEMBLY, 50"
HOSE ASSEMBLY, 33"
HOSE ASSEMBLY, 33"
SCREW, 1/4"-20 X 2-1/4" RD HD SLOTTED
NUT, 1/4"-20 HEX
WASHER, 1/4" FLAT
LOCKWASHER, 1/4" HELICAL
MOUNTING BRACKET, CHECK VALVE
VI-13
Section VI - PARTS (cont'd)
PUMP, VALVE & FILTER HYDRAULICS
VI-14
Section VI - PARTS (cont'd)
PUMP, VALVE & FILTER HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
1
1
2
6
1
2
15 FT
1
1
16 FT
1
3
1
1
3
1
2
1
1
2
3
1
1
2
3
4
4
1
2
0300052
0300136
0300287
0300364
0300434
0300446
0300558
0300615
0300666
0300671
0301373
0301545
0301637
0301659
0301696
0301836
0301894
0301904
0301905
0301961
0301965
0301995
0302052
0302083
0302205
0302227
0302228
0302242
0302296
DESCRIPTION
ELBOW, 8MJ-10MB90
RETURN LINE FILTER ASSEMBLY
BUSHING, 1-1/4" X 1"
CLAMP, HOSE, 1" 2-1/4"
HOSE BARB, 2", 32C4-32MP
PIPE PLUG, 3/4" NPT
SUCTION HOSE, 2"
ELBOW, 12MJ-12MP90
BARB, 24C4-24MP
SUCTION HOSE, 1-1/2"
PIPE BUSHING, 2" NPT TO 1-1/2" NPT
ELBOW, 12MJ-12MB90
ELBOW FLANGE, 32-32FL90 W/ FLANGE KIT
HOSE ASSEMBLY 150"
ELBOW, 6MJ-6FJX90
HYDRAULIC PUMP, OPPOSITE ENGINE
FILTER ASSEMBLY SPIN-ON
ELBOW, 8MJ-12FL90
O-RING FLANGE KIT, 12FH
BALL VALVE, BRONZE
HOSE ASSEMBLY, 131"
ADAPTER, 8FJ-6MJ
RUN TEE, 8MJ-8FJX-8MJ
ELBOW, 16MJ-12MB90
GAUGE, HYDRAULIC PRESSURE
CENTER BONDED MOUNT
SPECIAL WASHER
FLANGE FITTING, 24-24FL90
CONTROL VALVE, VDP12CDD118
VI-15
REF.
NO.
NO.
REQ'D
PART
NUMBER
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
2
1
2
3
1
2
2
2
2
6
2
1
2
2
2
3
4
4
2
12
2
24
4
2
1
1
2
2
0302367
0302466
0302570
0302577
0302798
0302826
0302829
0302901
0302932
0303290
0303338
0303340
0303341
0305006
0400081
20400122
0400150
0400177
0400367
0400392
0400451
0400482
0400491
0706114
0802429
0802430
0802747
0803193
DESCRIPTION
PIPE NIPPLE, 2" X 4"
AIR SHIFT PTO (NOT SHOWN)
SIGHT GAUGE
CONNECTOR, 6MJ-4FP
CONTROL VALVE, VDP11DDC10
TEE, 12MJ-12FJX-12MJ
ADAPTER, 12FJ-6MJ
HOSE ASSEMBLY 120"
ELBOW, 12MJ-20FL90 W/ FLANGE KIT
HOSE CLAMP, 2-1/2" INSULATED
ELBOW, 16MJ-16MP45
HOSE ASSEMBLY, 50"
HOSE ASSEMBLY, 36"
FILLER CAP
SCREW, 1/4"-20 X 3-1/2" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 2-1/2" HEX HD CAP
SCREW, 1/2"-13 X 1-1/4" HEX HD CAP
NUT, 1/4"-20 HEX NYLOK
NUT, 3/8"-16 HEX NYLOK
WASHER, 1/4" FLAT
LOCKWASHER, 3/8" HELICAL
LOCKWASHER, 1/2" HELICAL
GASKET, CLEANOUT & FILLER COVER
RESERVOIR WELDMENT, LEFT
RESERVOIR WELDMENT, RIGHT
FILLER PIPE WELDMENT
RESERVOIR SUPPORT WELDMENT
Section VI - PARTS (cont'd)
WINCH HYDRAULICS & AIR FREE SPOOL
VI-16
Section VI - PARTS (cont'd)
WINCH HYDRAULICS & AIR FREE SPOOL
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
2
4
4
10 FT.
2
10 FT.
1
2
4
2
5
5
10
4
2
2
1
1
1
1
2
4
5
16
16
4
2
2
2
2
2
0300324
0300897
0301093
0301577
0301610
0302431
0302607
0302677
0302678
0302827
0302835
0302836
0302837
0303079
0303344
0303345
0303349
0303350
0303351
0303352
0303504
0400034
0400118
0400288
0400431
0400455
0709702
0709703
0709704
0709705
GX263
DESCRIPTION
VALVE, SOLENOID AIR CONTROL
RUBBER GROMMET
BULKHEAD UNION, 3/4" JIC
AIR HOSE, 1/4" O.D.
CONNECTOR, 4TB-4MP
CONVOLUTED LOOM, 3/8"
TEE UNION, 4TB-4TB-4TB
BREATHER VENT, 1/8" MP
ELBOW, 1/4" TUBE X 1/8" MP 90
CONNECTOR, 10MJ-10MB
CLAMPING UNIT
STACKING NUT, SKT HD
SPLIT BUSHING, 11"
CONNECTOR, 10MJ-8MB
HOSE ASSEMBLY, 46"
HOSE ASSEMBLY, 48"
HOSE ASSEMBLY, 81"
HOSE ASSEMBLY, 89"
HOSE ASSEMBLY, 105"
HOSE ASSEMBLY, 117"
WINCH, DP MODEL S50-50K, SINGLE SPEED
SCREW, #10-32 X 1/2" RD HD PHIL
SCREW, 5/16"-18 X 3/4" HEX HD CAP
SCREW, 3/4"-10 X 2-1/2" HEX HD CAP
NUT, 3/4" HEX NYLOK
LOCKWASHER, #10 HELICAL
ANGLE - WINCH MOUNTING
ANGLE - WINCH MOUNTING
ANGLE - WINCH MOUNTING
ANGLE - WINCH MOUNTING
ELBOW, 10MJ-10MB90
VI-17
Section VI - PARTS (cont'd)
LEFT CONTROL ASSEMBLY
VI-18
Section VI - PARTS (cont'd)
LEFT CONTROL ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
1
2
1
2
1
1
4
9
1
1
12
4
2
9
4
4
2
4
9
36
10
9
4
24
10
9
9
2
1
1
1
1
6
1
9
0300341
0300834
0300835
0300836
0300837
0301884
0302457
0302726
0302856
0302917
0303008
0303427
0400066
0400103
0400107
0400122
0400367
0400379
0400382
0400383
0400392
0400393
0400451
0400466
0400512
0400532
0400541
0711235
0711245
0711246
0711284
0711285
0801054
0803182
0803294
DESCRIPTION
CONTROL KNOB, W/L (UP/DOWN)
CONTROL KNOB, (IN/OUT)
CONTROL KNOB, BOOM (UP/DOWN)
CONTROL KNOB, JACK (UP/DOWN)
CONTROL KNOB, BOOM (IN/OUT)
CONTROL CABLE, 96"
CONTROL CABLE, 104"
GREASE FITTING, 1/4"-28 X 45°
CONTROL KNOB, TILT (UP/DOWN)
CONTROL KNOB, W/L EXTEND (IN/OUT)
ADJUSTABLE CLEVIS
CONTROL CABLE, 114"
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 5/16"-18 X 1-1 /4" HEX HD CAP
SCREW, 5/16"-18 X 2-1/2" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
NUT, 1/4"-20 HEX NYLOK
NUT, 5/16"-18 "J" TINNERMAN
NUT, 5/16"-18 HEX NYLOK
NUT, 5/16"-24 HEX
NUT, 3/8"-16 HEX NYLOK
NUT, 3/8"-16 HEX JAM
WASHER, 1/4" FLAT
WASHER, 5/16" INTERNAL TOOTH
WASHER, 3/4" FLAT (SPECIAL)
CLEVIS PIN, 5/16" X 1"
COTTER PIN, 1/16" X 3/4"
CLAMP, SHAFT CONTROL BOX
PLATE, SHAFT SUPPORT
PIN, CONTROL BOX
SUPPORT, CONTROL (LEFT)
SUPPORT, CONTROL (RIGHT)
CONTROL CABLE CONNECTOR
CONTROL FRAME WELDMENT
CONTROL HANDLE WELDMENT
VI-19
REMOTE CONTROL ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
-36
37
38
39
40
41
42
43
44
45
46
47
-48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
-65
67
-10/16
1
15/25
2/4
2/3
2
2
1
35/65
1/2
16/28
1
1
1
1/2
1
1
8/20
4/7
1
1
1
2/4
4/7
2/4
2/4
6/11
4/7
2/4
4/7
1
1
4/7
1
-0300166
0301574
0301577
0301610
0301618
0302048
0302340
0302431
0302434
0302677
0302678
0302844
0303479
0303226
0303235
0303250
0303251
0303322
0303335
0303363
0303364
0303365
0400025
0400057
0400078
0400351
0400367
0400401
0400451
0400527
0711277
0711836
0803181
HAO132
DESCRIPTION
REMOTE CONTROL ASSEMBLY
WIRE CONNECTOR, SPADE
ELBOW, 4TB-4MP90
AIR HOSE, 1/4" O.D. (FT)
CONNECTOR, 4TB-4MP
BRASS PLUG, 4MP
CABLE SEALING GRIP
HEX PIPE BUSHING
CONVOLUTED LOOM, 3/8" X 8"
CABLE TIE, 4" 18 LB.
BREATHER VENT, 2MP
ELBOW, 4TB-2MP
AIR SOLENOID VALVE (8)
AIR SOLENOID VALVE (14)
CIRCUIT BREAKER, HI-AMP WATERPROOF
TERMINAL BLOCK
POWER PAL, 15 POSITION
POWER PAL, 8 POSITION
ELECTRICAL CABLE, 16/10 SO (FT)
AIR CYLINDER
AIR FILTER/REGULATOR
AIR LUBRICATOR
MOUNTING BRACKET
SCREW, #8-32 X 3/4" RD HD SLOTTED
SCREW, 1/4"-20 X 1-1/4" HEX HD CAP
SCREW, 1/4"-20 X 2" HEX HD CAP
HEX NUT & STAR WASHER, #8-32
NUT, 1/4"-20 HEX NYLOK
NUT, 7/16"-20 HEX JAM
WASHER, 1/4" FLAT
CLEVIS PIN, 5/16" X 5/8" COTTERLESS
SUPPORT, SOLENOID VALVE (8)
SUPPORT, SOLENOID VALVE (14)
CLEVIS WELDMENT
GAUGE, 0-160 PSI
Section VI - PARTS (cont'd)
RIGHT CONTROL ASSEMBLY
VI-20
Section VI - PARTS (cont'd)
RIGHT CONTROL ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
2
1
2
1
3
6
6
3
6
4
4
4
10
18
4
6
18
4
7
6
6
2
1
1
1
1
6
0300834
0300835
0300836
0300837
0302457
0302726
0303008
0303427
0400103
0400107
0400122
0400379
0400382
0400383
0400392
0400393
0400466
0400480
0400512
0400532
0400541
0711235
0711247
0711284
0711285
0803183
0803294
DESCRIPTION
CONTROL KNOB, (IN/OUT)
CONTROL KNOB, BOOM (UP/DOWN)
CONTROL KNOB, JACK (UP/DOWN)
CONTROL KNOB, BOOM (IN/OUT)
CONTROL CABLE, 104"
GREASE FITTING, 1/4"-28 X 45°
ADJUSTABLE CLEVIS
CONTROL CABLE, 114"
SCREW, 5/16"-18 X 1-1/4" HEX HD CAP
SCREW, 5/16"-18 X 2-1/2" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
NUT, 5/16"-18 "J" TINNERMAN
NUT 5/16"-1 8 HEX NYLOK
NUT, 5/16"-24 HEX
NUT, 3/8"-16 HEX NYLOK
NUT 3/8"-16 HEX JAM
WASHER, 5/16" INTERNAL TOOTH
WASHER, 3/8" FLAT
WASHER, 3/4" FLAT (SPECIAL)
CLEVIS PIN, 5/16" X 1"
COTTER PIN, 1/16" X 3/4"
CLAMP, SHAFT CONTROL BOX
PIN, CONTROL BOX
SUPPORT, CONTROL (LEFT)
SUPPORT, CONTROL (RIGHT)
CONTROL FRAME WELDMENT
CONTROL HANDLE WELDMENT
VI-21
Section VI - PARTS (cont'd)
REAR SPADE HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
6
2
20
REF.
2
2
4
0300044
0301522
0301601
0302296
0303017
0303691
0303748
DESCRIPTION
CONNECTOR, 6MJ-8MB
CONNECTOR, 6MJ-6MB
HOSE CLAMP, 5/8" INSULATED (NOT SHOWN)
CONTROL VALVE, VDP12CDD118
CONNECTOR, 8MB-6FB
HYDRAULIC CYLINDER
HOSE ASSEMBLY, 136"
VI-22
Section VI - PARTS (cont'd)
HYDRAULIC CYLINDERS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
2
1
0302792
0304489
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
1
0302830
0304490
DESCRIPTION
BOOM ELEVATION CYLINDER (COMPLETE)
SEAL KIT, BOOM ELEVATION CYLINDER
DESCRIPTION
BOOM EXTEND CYLINDER (COMPLETE)
SEAL KIT, BOOM EXTEND CYLINDER
VI-23
Section VI - PARTS (cont'd)
HYDRAULIC CYLINDERS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
2
1
0302791
0304489
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
1
0301811
0304243
DESCRIPTION
UNDERLIFT TILT CYLINDER (COMPLETE)
SEAL KIT, UNDERLIFT TILT CYLINDER
DESCRIPTION
UNDERLIFT EXTEND CYLINDER (COMPLETE)
SEAL KIT, UNDERLIFT EXTEND CYLINDER
VI-24
Section VI - PARTS (cont'd)
HYDRAULIC CYLINDERS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
1
0302537
0304459
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
2
1
0300680
0301353
DESCRIPTION
UNDERLIFT FOLD CYLINDER (COMPLETE)
SEAL KIT, UNDERLIFT FOLD CYLINDER
DESCRIPTION
REAR SPADE CYLINDER (COMPLETE)
SEAL KIT, REAR SPADE CYLINDER
VI-25
Section VI - PARTS (cont'd)
GLAD HAND KIT
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
1
2
2
2
2
1
2
2
2
2
2
0301909
0301944
0301945
0301946
0301947
0301948
0400070
0400367
0400451
0400463
0703795
DESCRIPTION
RECEPTACLE BOOT
GLAD HAND COUPLING, UNIVERSAL
GLAD HAND PLUG
CONNECTOR, BULKHEAD
45° ADAPTER, 1/4" NPM-3/8"
HD 7-WAY TRAILER CONNECTOR
SCREW, 1/4"-20 X 1" HEX HD CAP
NUT, 1/4"-20 HEX NYLOK
WASHER, 1/4" FLAT
WASHER, 5/16" FLAT
AIR HOSE, 3/8" SYNFLEX
VI-26
Section VI - PARTS (cont'd)
LIFT ADAPTERS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2
2
2
2
2
2
2
2
2
4
1
1
2
2
1
1
2
2
0200018
0200019
0200020
0200021
0200022
0200023
0200024
0400585
0711002
0800590
0801186
0801187
0801459
0802810
0803591
0803592
0900900
0902321
DESCRIPTION
FORK, SHORT (3" OPENING)
FORK, SHORT (4-1/2" OPENING)
FORK, MEDIUM (3" OPENING)
FORK, MEDIUM (4-1/2" OPENING)
FORK, LONG (3" OPENING)
FORK, LONG (4-1/2" OPENING)
FORK, OFFSET REAR AXLE (6" OPENING)
HAIR PIN COTTER, 1-1/4"
MODIFIED BOLT
TEE HANDLE
CHAIN HOOK ADAPTER, R.H.
CHAIN HOOK ADAPTER, L.H.
RISER BRACKET
SPRING LIFT BRACKET
OFFSET FORK ADAPTER, LT
OFFSET FORK ADAPTER, RT
RETAINER PIN ASSEMBLY
RETAINER PIN, SPRING LIFT BRACKET
VI-27
Section VI - PARTS (cont'd)
KING PIN ADAPTER
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
1
0803605
KING PIN ADAPTER WELDMENT
2
3
4
5
6
-1
2
1
1
1
0902782
0400555
HD1259
VA0660
VA0661
VA0662
FIFTH WHEEL ADAPTER (COMPLETE)
ROLL PIN, 3/8" X 1-1/2"
PIN, SNAPPER
5TH WHEEL PIVOT PLATE WELDMENT
PULL PIN WELDMENT
PIVOT PIN WELDMENT
7
8
9
10
-1
4
4
1
124002211
0302198
0400176
0400491
0803604
11
2
0902378
DESCRIPTION
PINTLE HOOK KIT (COMPLETE)
PINTLE HOOK (NOT SHOWN)
SCREW, 1/2"-13 X 1" HEX HD CAP
LOCKWASHER, 1/2" HELICAL
5TH WHEEL, KING PIN ADAPTER & PINTLE
HOOK BRACKET
RETAINING PIN ASSEMBLY
VI-28
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
2
3
0302542
0302543
0400025
DESCRIPTION
LIGHT, STOP & TURN
LIGHT, BACK-UP
SCREW, #8-32 x 3/4" RD HD SLOTTED
VI-29
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
2
3
0300442
0300507
0300511
REF.
NO.
PART
NUMBER
1
2
3
4
5
0301390
0304123
0304124
0304125
0304126
DESCRIPTION
3-LIGHT BAR ASSEMBLY, COMPLETE
BULB, MARKER LIGHT
LENS, 3-LIGHT BAR
DESCRIPTION
LIGHT, TURN (COMPLETE)
BEZEL MOUNTING SCREW
CHROME BEZEL
LENS & BULB ASSEMBLY
GROMMET & PLUG KIT
VI-30
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
0302201
REF.
NO.
PART
NUMBER
1
0302544
DESCRIPTION
LIGHT, FLOOD (COMPLETE)
DESCRIPTION
LIGHT, DOME (COMPLETE)
VI-31
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
2
3
0301741
0301742
0301740
REF.
NO.
PART
NUMBER
1
2
3
0300076
0300273
0300512
DESCRIPTION
LENS & BULB, RED MARKER
LENS & BULB, AMBER MARKER
GROMMET & PLUG KIT, MARKER LIGHT
DESCRIPTION
LICENSE PLATE BRACKET
LICENSE PLATE ILLUMINATOR (COMPLETE)
BULB, LICENSE PLATE ILLUMINATOR
VI-32
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
0302611
DESCRIPTION
AMBER MARKER LIGHT (COMPLETE)
VI-33
NOTES
NOTES
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive • Ooltewah, Tennessee 37363 • (423) 238-4171
www.millerind.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement