M2420 LiFePO4 charger S Charger type Name:LiFePo4 25,6V 2A battery charger

M2420 LiFePO4 charger S Charger type Name:LiFePo4 25,6V 2A battery charger
SM2420 LiFePO4 charger
1、Charger type
Name:LiFePo4 25,6V 2A battery charger
Type :8 serials-2A
2、Charger parameter
length
170mm
width
70 mm
height
47 mm
weight
0.34 kg
color
Black
Cooling way
Natural convection
Input volts
160V-240VAC input
Input frequency
50Hz / 60Hz
Appearance
Working performance
Maximum output voltage
29.2±0.5V
Maximum output current
2A
Charge type
CC/CV
Working Temperature
0°C to 50° C
Storage temperature
Working environment
Humidity
95%
concussion
quiver
guaranty
-20°C to +65° C
About 10g
10-55HZ,1.5mm(double
amplitude)
One year
3、
、Charge process
The converting point is set to 3.65V, from CC to CV .
4.
.Instruction
1)Be sure that output wires of charger should be rightly connected with the
battery, otherwise the charger will not work.
Warning: Do not connect pole of the charger and battery in reversed
condition.
2). There should be a good earth line after connected to AC power.
Notice: When the battery is not connected, the charger do not work to
output for the reason of safety.
3)When connected to the power, turn on the switch and the RUN LED will light
on, then the charger begin to work and the fan start to rotate.
4). During charging, the RUN LED will light on, CHARGE LED will turn out to
be red.
CHARGE LED indicates the status of the charger.
Red, yellow and green color
show different charge status. The light will change color automatically for every
status.
5)When CHARGE green light was on, charger will be turn off automatically and
the fan will stop.
6)After charging finished, pull off the plug will disconnect the AC power.
5、
、simple failure treatments:
!
warning!Maintenance and repair is limited to professionals only.
NO.
FAILURE
Charger
fail
CAUSE
to
work, and indicator
LED
does
Treatment approach
not
shine.
Check whether the battery voltage is
The battery voltage is
too
low
or
poor
connect .
contact .
Input
power
connected
is
or
not
power
connection is bad.
The indicator LED
shines,but charger
Charger running too hot
the power plug is loose.
not,or the cooling fan is working
correctly.
The
Charger
is
connected reversely to
People
Battery failed to be
anode and cathode of
mistake,need sent it back to repair.
charged.
the battery.
Charger fault
4
Check AC power is normal or not,or
Check the charger vent is clear or
fail to work
3
voltage. check the charger and the
battery is connected or in pool
1
2
below the discharge protection
The Status indicator
Battery voltage level is
LED
only
over charging voltage of
lighting for a short
the charger or a the of
time then charger
battery capacity is too
auto-off.
low .
is
themselves
made
the
If charger internal wires fault, then
need send it back to repair.
First check the battery voltage level,
and then check the battery is aging.
Remark: If the handle is invalid, please contact our company in time to resolve.
、 guaranty
6、
Our chargers could be replaced within two months if there are any quality
problems. And we provide one year guaranty.
Warranty does not include the following circumstances.
1、users made improper operation.
2、man-made damage, shell deformed or damaged.
3、wire and cable of input and output are damaged.
4、the sealed labels posted by our company is torn and damaged.
※We will charge the maintenance and repair of the charger that are not in the scope
of warranty or out of warranty time.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement