BCR5FM-14LJ Data Sheet

BCR5FM-14LJ Data Sheet
Preliminary Datasheet
BCR5FM-14LJ
R07DS0961EJ0100
Rev.1.00
Nov 19, 2012
700V - 5A - Triac
Medium Power Use
Features




 Insulated Type
 Planar Passivation Type
 Viso: 2000 V
IT (RMS) :5 A
VDRM : 800 V (Tj = 125°C)
Tj: 150°C
IFGTI, IRGTI, IRGT III : 30 mA
Outline
RENESAS Package code: PRSS0003AG-A
(Package name: TO-220FP)
2
1. T1 Terminal
2. T2 Terminal
3. Gate Terminal
3
1
1
2 3
Applications
Switching mode power supply, Washing machine, small motor controller, copying machine, electric heater control, and
other general controlling devices
Maximum Ratings
Parameter
Repetitive peak off-state voltageNote1
VDRM
Non-repetitive peak off-state voltageNote1
VDSM
Parameter
Voltage class
Symbol
14
800
700
840
Unit
V
V
V
Conditions
Tj = 125C
Tj = 150C
Symbol
Ratings
Unit
RMS on-state current
IT (RMS)
5
A
Commercial frequency, sine full wave
360 conduction, Tc = 113C
Surge on-state current
ITSM
50
A
60 Hz sinewave 1 full cycle, peak
value, non-repetitive
I2 t
10.4
A2s
PGM
PG (AV)
VGM
IGM
Tj
Tstg
—
Viso
5
0.5
10
2
–40 to +150
–40 to +150
1.9
2000
W
W
V
A
C
C
g
V
I2t for fusion
Peak gate power dissipation
Average gate power dissipation
Peak gate voltage
Peak gate current
Junction Temperature
Storage temperature
Mass
Isolation voltage Note5
R07DS0961EJ0100 Rev.1.00
Nov 19, 2012
Conditions
Value corresponding to 1 cycle of half
wave 60 Hz, surge on-state current
Typical value
Ta = 25C, AC 1 minute,
T1  T2  G terminal to case
Page 1 of 7
BCR5FM-14LJ
Preliminary
Electrical Characteristics
Parameter
Repetitive peak off-state current
On-state voltage
Symbol
IDRM
VTM
Min.
—
—
Typ.
—
—
Max.
2.0
1.8
Unit
mA
V
Test conditions
Tj = 150C, VDRM applied
Tc = 25C, ITM = 7A,
instantaneous measurement
Gate trigger voltageNote2



VFGT
VRGT
VRGT
—
—
—
—
—
—
1.5
1.5
1.5
V
V
V
Tj = 25C, VD = 6 V, RL = 6 ,
RG = 330 
Gate trigger curentNote2



IFGT
IRGT
IRGT
—
—
—
—
—
—
30
30
30
mA
mA
mA
Tj = 25C, VD = 6 V, RL = 6 ,
RG = 330 
VGD
Rth (j-c)
(dv/dt)c
0.2/0.1
—
5
1
—
—
—
—
—
4.9
—
—
V
C/W
V/s
V/s
Gate non-trigger voltage
Thermal resistance
Critical-rate of rise of off-state
commutation voltageNote4
Notes: 1.
2.
3.
4.
5.
Tj = 125C/150C, VD = 1/2 VDRM
Junction to caseNote3
Tj = 125C
Tj = 150C
Gate open.
Measurement using the gate trigger characteristics measurement circuit.
The contact thermal resistance Rth (c-f) in case of greasing is 0.5C/W.
Test conditions of the critical-rate of rise of off-state commutation voltage is shown in the table below.
Make sure that your finished product containing this device meets your safe isolation requirements.
For safety, it's advisable that heatsink is electrically floating.
Test conditions
1. Junction temperature
Tj = 125C/150C
2. Rate of rise of off-state commutating voltage
(dv/dt)c = 2.5 A/ms
3. Peak off-state voltage
VD = 400 V
R07DS0961EJ0100 Rev.1.00
Nov 19, 2012
Commutating voltage and current waveforms
(inductive load)
Supply Voltage
Time
Main Current
(di/dt)c
Time
Main Voltage
(dv/dt)c
Time
VD
Page 2 of 7
BCR5FM-14LJ
Preliminary
Performance Curves
Maximum On-State Characteristics
Rated Surge On-State Current
101
Surge On-State Current (A)
100
Tj = 150°C
100
Tj = 25°C
10−1
0
1
2
3
20
101
102
Gate Characteristics (I, II and III)
Gate Trigger Current vs.
Junction Temperature
PGM = 5W
101
PG(AV) =
0.5W
IGM = 2A
VGT = 1.5V
100
IRGT I
VGD = 0.1V
IFGT I, IRGT III
102
103
104
103
Typical Example
102
IFGT I
IRGT I
IRGT III
101
–40
0
40
80
120
160
Gate Current (mA)
Junction Temperature (°C)
Gate Trigger Voltage vs.
Junction Temperature
Maximum Transient Thermal Impedance
Characteristics (Junction to case)
103
Typical Example
102
101
–40
Gate Trigger Current (Tj = t°C)
× 100 (%)
Gate Trigger Current (Tj = 25°C)
Gate Voltage (V)
40
Conduction Time (Cycles at 60Hz)
101
Gate Trigger Voltage (Tj = t°C)
× 100 (%)
Gate Trigger Voltage (Tj = 25°C)
60
On-State Voltage (V)
VGM = 10V
10−1
80
0
100
4
0
40
80
120
Junction Temperature (°C)
R07DS0961EJ0100 Rev.1.00
Nov 19, 2012
160
Transient Thermal Impedance (°C/W)
On-State Current (A)
102
102
6
103
104
100
101
5
4
3
2
1
0 −1
10
102
Conduction Time (Cycles at 60Hz)
Page 3 of 7
BCR5FM-14LJ
Preliminary
8
10
2
101
100
10−1
101
102
103
104
7
6
5
4
3
2
360° Conduction
Resistive,
inductive loads
1
0
105
0
1
2
3
4
5
6
7
8
Conduction Time (Cycles at 60Hz)
RMS On-State Current (A)
Allowable Case Temperature vs.
RMS On-State Current
Allowable Ambient Temperature vs.
RMS On-State Current
160
Curves apply regardless
of conduction angle
140
Ambient Temperature (°C)
Case Temperature (°C)
On-State Power Dissipation (W)
No Fins
160
120
100
80
60
40
360° Conduction
20 Resistive,
inductive loads
0
0
1
2
3
4
5
6
7
140
60 × 60 × t2.3
120
100 × 100 × t2.3
80
60
40 Curves apply regardless
All fins are
black painted
aluminum
and greased
of conduction angle
Resistive, inductive loads
Natural convection
20
0
8
120 × 120 × t2.3
100
0
1
2
3
4
5
6
7
8
RMS On-State Current (A)
RMS On-State Current (A)
Allowable Ambient Temperature vs.
RMS On-State Current
Repetitive Peak Off-State Current vs.
Junction Temperature
160
Ambient Temperature (°C)
Maximum On-State Power Dissipation
103
Natural convection
No Fins
Curves apply regardless
of conduction angle
Resistive, inductive loads
140
120
100
80
60
40
20
0
0
0.5
1.0
1.5
2.0
2.5
RMS On-State Current (A)
R07DS0961EJ0100 Rev.1.00
Nov 19, 2012
3.0
Repetitive Peak Off-State Current (Tj = t°C)
× 100 (%)
Repetitive Peak Off-State Current (Tj = 25°C)
Transient Thermal Impedance (°C/W)
Maximum Transient Thermal Impedance
Characteristics (Junction to ambient)
106
Typical Example
105
104
103
102
–40
0
40
80
120
160
Junction Temperature (°C)
Page 4 of 7
BCR5FM-14LJ
Preliminary
Holding Current vs.
Junction Temperature
Latching Current vs.
Junction Temperature
103
Distribution
Typical Example
101
Latching Current (mA)
Holding Current (mA)
102
Distribution
102
101
T2+, G+
Typical Example
T2–, G–
VD=12V
0
40
80
120
0
40
80
120
160
Junction Temperature (°C)
Breakover Voltage vs.
Junction Temperature
Breakover Voltage vs.
Rate of Rise of Off-State Voltage (Tj=125°C)
140
120
100
80
60
40
20
Typical Example
0
40
80
120
160
Breakover Voltage (dv/dt = xV/μs)
× 100 (%)
Breakover Voltage (dv/dt = 1V/μs)
Junction Temperature (°C)
160
0
–40
100
–40
160
160
140
120
III Quadrant
100
80
I Quadrant
60
40
Typical Example
Tj = 125°C
20
0 1
10
102
103
104
Junction Temperature (°C)
Rate of Rise of Off-State Voltage (V/μs)
Breakover Voltage vs.
Rate of Rise of Off-State Voltage (Tj=150°C)
Commutation Characteristics (Tj=125°C)
102
160
Critical Rate of Rise of Off-State
Commutating Voltage (V/μs)
Breakover Voltage (dv/dt = xV/μs)
× 100 (%)
Breakover Voltage (dv/dt = 1V/μs)
Breakover Voltage (Tj = t°C)
× 100 (%)
Breakover Voltage (Tj = 25°C)
100
–40
T2+, G–
Typical Example
140
120
III Quadrant
100
80
60
I Quadrant
40
20 Typical Example
Tj = 150°C
0 1
10
102
103
104
Rate of Rise of Off-State Voltage (V/μs)
R07DS0961EJ0100 Rev.1.00
Nov 19, 2012
101
Time
Main Voltage
(dv/dt)c
VD
Main Current
(di/dt)c
IT
τ
Time
Minimum
Value
Typical Example
Tj = 125°C
IT = 4A
τ = 500μs
VD = 200V
f = 3Hz
III Quadrant
I Quadrant
100
100
101
102
103
Rate of Decay of On-State
Commutating Current (A/ms)
Page 5 of 7
BCR5FM-14LJ
Preliminary
Gate Trigger Current vs.
Gate Current Pulse Width
Critical Rate of Rise of Off-State
Commutating Voltage (V/μs)
102
Time
Main Voltage
(dv/dt)c
VD
Main Current
(di/dt)c
IT
τ
Time
Typical Example
Tj = 150°C
IT = 4A
τ = 500μs
VD = 200V
f = 3Hz
101
III Quadrant
I Quadrant
Minimum
Value
100
100
101
102
Gate Trigger Current (tw)
× 100 (%)
Gate Trigger Current (DC)
Commutation Characteristics (Tj=150°C)
103
Typical Example
IRGT III
IRGT I
102
IFGT I
101
100
101
102
Rate of Decay of On-State
Commutating Current (A/ms)
Gate Current Pulse Width (μs)
Gate Trigger Characteristics Test Circuits
Recommended Circuit Values Around The Triac
6Ω
6Ω
Load
C1
A
6V
V
Test Procedure I
R1
A
6V
330Ω
V
330Ω
Test Procedure II
C0
R0
C1 = 0.1 to 0.47μF C0 = 0.1μF
R1 = 47 to 100Ω
R0 = 100Ω
6Ω
A
6V
V
330Ω
Test Procedure III
R07DS0961EJ0100 Rev.1.00
Nov 19, 2012
Page 6 of 7
BCR5FM-14LJ
Preliminary
Package Dimensions
Package Name
TO-220FP
JEITA Package Code

RENESAS Code
PRSS0003AG-A
Previous Code

MASS[Typ.]
1.9g
Unit: mm
10.16 ± 0.20
2.54 ± 0.20
6.68 ± 0.20
3.3 ± 0.2
1.28 ± 0.30
3.18 ± 0.20
12.98 ± 0.30
15.87 ± 0.20
3.18 ± 0.10
Max 1.47
2.76 ± 0.20
0.80 ± 0.20
0.50
4.7 ± 0.2
5.08 ± 0.20
Ordering Information
Orderable Part Number
BCR5FM-14LJ#BB0
BCR5FM-14LJ-A8#BB0
Note:
Packing
Tube
Tube
Quantity
50 pcs.
50 pcs.
Remark
Straight type
A8 Lead form
Please confirm the specification about the shipping in detail.
R07DS0961EJ0100 Rev.1.00
Nov 19, 2012
Page 7 of 7
Notice
1.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the
use of these circuits, software, or information.
2.
Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics
3.
Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or
assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.
technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or
others.
4.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Renesas Electronics assumes no responsibility for any losses incurred by you or
5.
Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The recommended applications for each Renesas Electronics product depends on
third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product.
the product's quality grade, as indicated below.
"Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic
equipment; and industrial robots etc.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc.
Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical
implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it
in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses
incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics.
6.
You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage
range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the
use of Renesas Electronics products beyond such specified ranges.
7.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and
malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the
possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to
redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult,
please evaluate the safety of the final products or systems manufactured by you.
8.
Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics
products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes
no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
9.
Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or
regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the
development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations.
10. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the
contents and conditions set forth in this document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics
products.
11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries.
(Note 1)
"Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
(Note 2)
"Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
http://www.renesas.com
SALES OFFICES
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A.
Tel: +1-408-588-6000, Fax: +1-408-588-6130
Renesas Electronics Canada Limited
1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada
Tel: +1-905-898-5441, Fax: +1-905-898-3220
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-651-700, Fax: +44-1628-651-804
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-65030, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China
Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898
Renesas Electronics Hong Kong Limited
Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2886-9318, Fax: +852 2886-9022/9044
Renesas Electronics Taiwan Co., Ltd.
13F, No. 363, Fu Shing North Road, Taipei, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre Singapore 339949
Tel: +65-6213-0200, Fax: +65-6213-0300
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics Korea Co., Ltd.
11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5141
© 2012 Renesas Electronics Corporation. All rights reserved.
Colophon 2.2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement